Skylane Optics SPP13002100D538 User Manual
Displayed below is the user manual for SPP13002100D538 by Skylane Optics which is a product in the Network Transceiver Modules category. This manual has pages.
Related Manuals
DATASHEET SPP1301010XD P01
SPP1301010xD – SFP+ Dual Fibre
1310nm / 10km / 10× Gigabit Ethernet
DATASHEET - REV C
Figure 1. SFP+ Dual Fiber
(non-binding illustration)
SPP1301010xD is a high performance transceiver module for up to 10× Gigabit
Ethernet data links over a single mode bre pair. The maximum reach1 is 10 km,
with 6.2 dB end of life (EOL) power budget. The transmitter is a 1310 nm DFB
laser, the receiver is a PIN photodiode.
This transceiver module is compliant with the Small Form-factor Pluggable
(SFP+) Multisource Agreement (MSA) and hot pluggable. Always contact
Skylane Optics® commercial agents for compatibility with dierent equipment
platforms.
#01 Overview
Datasheet SPP1301010xD
P02
• SFP+ Multi-Source Agreement compliant (SFF-8431)
• Hot pluggable SFP+ footprint
• Serial ID functionality supported according to (SFF-8472)
• Class 1 laser safety standard IEC 60825 compliant
• Dual LC connector
• 1310 nm DFB transmitter
• 10 km point-to-point transmission on single mode bre
• Operating temperature range 0°C to 70°C or -40°C to 85°C
• Low power dissipation (< 1W)
• Digital diagnostics monitoring (DDM)
#02 Features
DATASHEET SPP1301010XD
• 10× Gigabit Ethernet
• 8× Fiber Channel
• 4× Fiber Channel
• 2× Fiber Channel
#03 Applications
#04 Optical Interface
P/N SPP1301010xD
Wavelength [nm] 1310
Optical Output Power2 [dBm] -8.2 to 0.5
Receiver Sensitivity3 [dBm] ≤ -14.4
Dispersion Penalty [dB] 3.2
Receiver Overload4 [dBm] 0
Power Budget2 [dB] ≥ 6.2
1. Distance is estimated assuming typical optical losses after decent quality fibre deployment; Only optical budget
value is guaranteed.
2. EOL, over operating temperature range
3. Measured at 10.3125Gbps, PRBS 231-1, BER≤10-12
4. The optical input to the receiver should not exceed this value. Transmitters must never be directly connected to
receivers (optical loop back) before ensuring that proper optical attenuation is used
#05 Technical Parameters
5.1. Recommended Operating Conditions
Parameter Min Typ Max Unit Notes
Storage temperature -40 85 °C
Operating Case Temperature 070 °C SPP13010100D
-40 85 °C SPP13010102D
Relative Humidity 595 %Non condensing
Power Supply Voltage 3.15 3.3 3.45 V
Power Supply Current 300 mA
5.2. Transmitter Optical Specications
Parameter Min Typ Max Unit Notes
Average Output Power -8.2 0.5 dBm 5
Centre Wavelength 1270 1310 1355 nm
Spectral Width (-20dB) 1nm
Extinction Ratio 3.5 dB
Dispersion Penalty 3.2 dB
5.3. Receiver Optical Specications
Parameter Min Typ Max Unit Notes
Receiver Sensitivity -14.4 dBm 6
Receiver Overload -6 dBm 6
Receiver Operating Range 1260 1565 nm
Datasheet SPP1301010xD
P03DATASHEET SPP1301010XD
5. Output power coupled into a 9/125 μm single-mode fibre
6. Measured with 10.3125Gbps PRBS 231-1, BER≤10-12
Datasheet SPP1301010xD
P04DATASHEET SPP1301010XD
#06 Transceiver Electrical Pad Layout
< TOWARDS BEZEL
TOWARDS ASIC >
20 19 18 17 16 15 14 13 12 11
VeeT TD- TD+ Veet VccT VccR VeeR RD+ RD- Veer
VeeT Tx_Fault Tx_D sable SDA SCL MOD_ABS RS0 Rx_LOS RS1 VeeR
12345678910
Figure 2. Transceiver Electrical Pad Layout
Datasheet SPP1301010xD
DATASHEET SPP1301010XD
#07 Module Electrical Pin Denition
SFP+ MSA (SFF-8431)
Pin Symbol Description Pin Symbol Description
1 VeeT Module Transmitter Ground 11 VeeR Module Receiver Ground
2 Tx_Fault Module Transmitter Fault 12 RD- Receiver Inverted Data Output
3 Tx_ Disable Transmitter Disable 13 RD+ Receiver Non-Inverted Data Output
4SDA 2-Wire Serial Interface Data 14 VeeR Module Receiver Ground
5 SCL 2-Wire Serial Interface Clock 15 VccR Module Receiver 3.3V Supply
6Mod_ABS Module Absent 16 VccT Module Transmitter 3.3V Supply
7RS0 Rate Select 0 17 VeeT Module Transmitter Ground
8 Rx_LOS Receiver Loss of Signal 18 TD+ Transmitter Non-Inverted Data Input
9 RS1 Not Used 19 TD- Transmitter Inverted Data Input
10 VeeR Module Receiver Ground 20 VeeT Module Transmitter Ground
P05
Datasheet SPP1301010xD
P06DATASHEET SPP1301010XD
#08 EEPROM - SFP+ MSA (SFF-8472)
Figure 3. EEPROM of a SFP+
A0H A2H
2 wire address 1010000x
Serial ID Dened
by SFP MSA (96 Bytes)
Vendor Specics (32 Bytes)
Reserved (128
Bytes)
2 wire address 1010001x
Alarm and
Warning-
Thresholds
(56 Bytes)
Cal Constants (40 Bytes)
Real Time
Diagnostic
Interface
(24 Bytes)
Vendor Specics (8 Bytes)
User writable
EEPROM
(120
Bytes)
Vendor Specics (8 Bytes)
Datasheet SPP1301010xD
P07DATASHEET SPP1301010XD
#09 Ordering information
Part Number Description
SPP13010100D
SFP+ Dual Fibre, Tx 1310 nm (DFB) , Rx (PIN), maximum distance
10 km, power budget 6.2 dB, 10x Gigabit Ethernet, LC connector,
0°C to 70°C, DDM
SPP13010102D
SFP+ Dual Fibre, Tx 1310 nm (DFB) , Rx (PIN), maximum distance
10 km, power budget 6.2 dB, 10x Gigabit Ethernet, LC connector,
-40°C to 85°C, DDM
SPP1301010GD
SFP+ Dual Fibre, Tx 1310 nm (DFB) , Rx (PIN), maximum distance
10 km, power budget 6.2 dB,10x Gigabit Ethernet, LC connector,
0°C to 70°C, DDM, Specic Firmware
SPP1301010AD
SFP+ Dual Fibre, Tx 1310 nm (DFB) , Rx (PIN), maximum distance
10 km, power budget 6.2 dB, 10x Gigabit Ethernet, LC connector,
0°C to 70°C, DDM, Specic Firmware
Datasheet SPP1301010xD
P08DATASHEET SPP1301010XD
Revision Description
RevA Initial release
RevB Specication updated to include 8x
Fiber Channel compatibility
RevC Ordering information table updated
with the “G” and “A” versions
#10 Document Revision Information
For your product safety, please read the following information carefully before any manipulation of the box:
ESD
This transceiver is specied as ESD threshold 1kV for SFI pins and 2kV
for all others electrical input pins, tested per MIL-STD-883G, Method
3015.4 /JESD22-A114-A (HBM). However, normal ESD precautions are
still required during the handling of this module.
LASER SAFETY
This is a Class1 Laser Product according to IEC 60825-1:2007.
This product complies with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No. 50, dated (June 24, 2007).
Skylane Optics® supplies a broad range of optical transceivers. Our engineers work closely with our customers to nd the best solutions for every application.
We are committed to provide high quality products and services to our customers.
For questions on this product please contact: support@skylaneoptics.com