StarTech.com ST7C51224 User Manual
Displayed below is the user manual for ST7C51224 by StarTech.com which is a product in the Mobile Device Chargers category. This manual has pages.
Related Manuals
Quick-Start Guide
To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.
Product Diagram (ST7C51224)
Port/LED Function
1USB-A Ports (7)
• Used to charge multiple Devices.
Note: 2A Devices can be charged using a
USB-A (1A) Port, and 1A Devices can be
charged in the USB-A (2A) Port, however, the
charging time will be aected.
2Power LED • Solid red indicates that the Charging Hub is
receiving power.
3 Power Button • Used to turn the Charging Hub On or O.
4DC IN 12V • Used to power the Charging Hub.
7 Port USB Dedicated Charging Station |5 x 1A | 2 x 2A
3
Requirements
For the latest requirements, please visit www.startech.com/ST7C51224 .
Installation
Notes: The Charging Hub features a chipset that can detect the required charging
mode of a device, and switch to the proper mode for full-speed charging (e.g. If an
Apple device is connected, it will automatically charge to Apple charging mode
specications).
When charging multiple devices, the Charging Hub may become warm to the touch,
this is normal and will not harm the connected Device(s).
1. Connect the Power Adapter to an AC Electrical Outlet and to the DC IN 12V Port
on the Charging Hub.
2. Press the Power Button to turn the Charging Hub On. Wait until the Power LED is
solid before connecting any devices for charging.
3. Connect your device(s) to the corresponding USB-A Port (1A or 2A) on the
Charging Hub, according to the charging requirements of the connected Device(s):
• 1A:
• Voltage at the common collector (VCC) = 5V
• Ground (GND) = 5V
• D+ = 2.0V
• D- = 2.7V
• 2A:
• Voltage at the common collector (VCC) = 5V
• Ground (GND) = 5V
• D+ = 2.7V
• D- = 2.0V
Installing the Mounting Brackets (Optional)
1. Align the Mounting Holes on the Mounting Bracket with the four Mounting Holes
on the back of the Charging Hub.
2. Insert the Bracket Screws (x4) through the Mounting Bracket and into the
Mounting Holes on the back of the Charging Hub.
3. Tighten the Mounting Screws using a Phillips Head Screwdriver, be careful not to
over-tighten.
4
2
1
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void
the user’s authority to operate the equipment.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 0.5cm
between the radiator and your body.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-
party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only
and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which
this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered
trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the
property of their respective holders.
Warranty Information
This product is backed by a two-year warranty.
For further information on product warranty terms and conditions, please refer to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)
for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of
business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.
Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations
or exclusions contained in this statement may not apply to you.
Safety Measures
• If product has an exposed circuit board, do not touch the product under power.
Mesures de sécurité
• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.
安全対策
• 製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。
Misure di sicurezza
• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.
Säkerhetsåtgärder
• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.
FR: fr.startech.com
DE: de.startech.com
ES: es.startech.com
NL: nl.startech.com
IT: it.startech.com
JP: jp.startech.com
StarTech.com Ltd.
45 Artisans Cres
London, Ontario
N5V 5E9
Canada
StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Rd,
Brackmills
Northampton
NN4 7BW
United Kingdom
StarTech.com LLP
2500 Creekside
Parkwy
Lockbourne, Ohio
43137
U.S.A.
4. Before installing the Mounting Bracket to the mounting surface, contact a
professional. Product mounting should be completed by a certied professional as
per the local safety and building code guidelines.
(Optional) Installing the Rubber Feet
1. Remove the Rubber Feet from the Adhesive Strip.
2. Align each of the Rubber Feet on the back of the Charging Hub, close to each of the
four corners.
3. Remove the adhesive backing and apply the Rubber Feet in the desired positions.
Note: Be careful not to cover the Mounting Holes when applying the Rubber Feet.