Techly IDATA EXTIP-329 User Manual
Displayed below is the user manual for IDATA EXTIP-329 by Techly which is a product in the AV Extenders category. This manual has pages.
Related Manuals
Features
1 . Applies advanced HDbitT over IP technology
2 . Transmits HDMI signal over any simple 2 conductor cables, it could be
network cable, power line, coaxial cable, telephone wire etc
3 . Supported resolution is up to full HD 1080p@60Hz
4 . Transmission distance is up to 300 meters
5 . IR passback for controlling the transmitter side source signal easily
from the receiver side
6 . Supports bi-directional RS232 pass back
7 . Supports one way HDMI loop output
8 . Plug and play, easy for installation
9 . Supports multicast that one transmitter unit is capable of driving up
to 4 receiver units
Package Content
1. HDMI source device(computer graphics card, DVD,PS3, HD
monitoring equipment etc)
2. HDMI display device like SDTV, HDTV, projector with HDMI por t
3. Any 2 conductor cables,like:network cable, power line, coaxial cable,
telephone wire etc.
Installation Requirements
1. HDMI EXTENDER TX (Transmitter)
Panel Description
Thank you for purchasing this product. For optimum performance
and safety, please read the instructions carefully and keep the manual
for future reference. Please read below safety instructions carefully
before installation and operation:
1.Please pay attention to all the warnings and hints on this device.
2.Do not expose this unit to rain, moisture and liquid.
3.Do not put any stuff into the device.
4.Do not repair or open this device without professional people's
guidance.
5.Make sure good ventilation openings to avoid product overheating
damage.
6.Shut off power and make sure environment is safe before installation.
7.Do not plug-in/out the connected cables when it is in using.
8.Make sure the specification matched if using 3rd party DC adapters.
Important Safety Instruction
Product Introduction
This Extender transmits and receives HDMI signal over any simple
2 conductor cables, such 2 conductor cables can be network cable,
power line, coaxial cable, telephone wire etc. This extender includes a
transmitter unit and a receiver unit, transmission distance is up to 300
meters. It supports multicast that one transmitter unit is capable of
driving up to 4 receiver units using either 4 individual wire pairs over
300m each, or daisy chaining the receivers. IR passback for controling
the transmitter side source signal easily from the receiver side. In
additional, it is with RS232 serial port that supports bi-directional RS232
pass back .This product is widely used in home theater system, media
projects, entertainment and exhibition center.
IR O UT IR IN
IR blaster extension
cable x1pcs
IR receiver extension
cable x1pcs
DC12V/2A ×2pcs RS232 serial port
cap ×2pcs
3
1
2
4
Terminal Port(Any 2 conductor)
Power input（DC12V）
Bi-directionl RS232 pass back
IR signal output to connect
with blaster extension cable
5
7
6
9
8
HDMI signal output
HDMI signal input
Data transmission light
Network link light
Reset button
2. HDMI EXTENDER RX(Receiver)
3
1
2
4
Terminal Post(Any 2 conductor)
Power input（DC12V）
IR signal input to connect with
IR receiver extension cable
5
7
6
8
HDMI signal output
Data transmission light
Network link light
Reset button
Connections
1. Unicast configuration:Up to 30 meters transmission distance over
Any 2 conductor cables
2. Multicast configuration:one transmitter to four receivers,realize
extender & splitter funtion
Connection instruction
1 ) Connect source device to Transmitter unit (TX), and display
device to Receiver unit (RX) via HDMI cables.
2 ) Connect Transmitter unit (TX) and Receiver unit (RX) via any
2 conductor cable.
3 ) Plug the power supply to Transmitter unit and Receiver unit (RX).
3
1
24
56
7
8
TV
HDMI OU T
Any 2 conductor
cables
13567
8
9
24
HDMI EXTENDER
Transmitter ×1pcs
HDMI EXTENDER
Receiver ×1pcs
User Manual ×1pcs
TV
Any 2 conductor
cables
TV
HDMI OU T
TV
TV
TV
HDMI OU T
HDMI OU T
HDMI OU T
HDMI OU T
HDMI IN
TV
HDMI IN
Transmitter
Receiver
Receiver
Receiver
Receiver
Receiver
Transmitter
Bi-directionl RS232 pass back
GND
TXD
RXD
line
line
line
IR User Guide
1 ) IR blaster extension cable should plug-in the IR-out port of
transmitter of HDMI extender, and the IR receiver extension cable
should plug-in the IR-out port of the receiver of HDMI extender.
2 ) The emitter of IR blaster should be as close as possible to the IR
receiver of the signal source device.Using the IR remote controller
of the signal source device towards the IR receiver (connected to
the RX of HDMI extender), to remote control source media playback.
1 ) Different encoding mechanism can not mix-connect, the baud rate
of RS232 serial of these transmitter unit and receiver unit, support
2400,4800, 9600, 19200, 28800, 38400, 57600, and 115200.
2 ) Line order
Check and make sure the RS23S serial line connect firmly and well,
and make sure serial data line is connected correctly as below:
If the RS232 serial does not work by following above connection,
please tr y to change the order of TXD line and RXD line.
Q: TV display “Waiting for connection” on the right corner?
A: Please check if the power supply of transmitter and switcher (if used)
is connected, and make sure connecting cable is firmly.
Q: TV display “Please check the transmitter input signal”？
A: 1 ) please check if there is a HDMI signal input of transmitter.
2 ) Try to connect the signal source directly to display device to see if
there is singal output from source device or change the signal
source, HDMI wire and try again.
Q：Display not fluent, not stable?
A：1 ) Please check the cable length between the transmitter to the
receiver the required range, make sure connecting cable is well
and Without interference.
2 ) Press "reset" button on the transmitter/receiver front panel, reset
and reconnect.
FAQ
3 ) Check baud rate
If you need to check the baud rate at last time, firstly, before power
on, set the baud rate to 115200 on your serial port test tool . Then,
power on, when the RS232 serial of product connects to serial port
test tool, the software will read out the baud rate at present.
e.g.: software show information “ Baud rate: 9600”, means 9600 is
the current baud rate.
4 ) Set baud rate
For example: the current baud rate is 9600, but the baud rate of
control equipment is 19200, so it needs to set the baud rate to
9600. At this time, in serial port tool, choose baud rate "9600", then
input command "set: 19200" in character format and send it out.
HDbitT HDMI Extender over Any Two
Conductor Cables
User Manual
Specification
HDMI Signal
Support resolutions
Audio format
Transmission distance
IR signal
ItemsSpecifications
HDMI1.3, Compatible with HDCP1.3
480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz,
720p@50/60Hz, 1080i@50/60Hz, 1080p@50/60Hz
PCM
Transmission distance is up to 300 meters.
Supports 20~60KHz IR devices
Working Temperature
Power Supply
Power Consumption
Dimensions
RS232
DC12V/2A
0℃～60℃
TX: 7.5W; RX: 7W
Supports Bi-directional RS232 pass back
Weight
Color Black
228(L)x125.4(W)x25(H)mm
210g*2pcs
Storage temperature
-20～70℃
Network bandwidth18M bps
Disclaimer
The product name and brand name may be registered trademark of
related manufacturers.TM and ® may be omitted on the user manual.
The pictures on the user manual are just for reference,and there may be
some slight difference with the real products.
We reserve the rights to make changes without further notice to a
product or system described herein to improve reliability, function or
design.