Table of Contents
- Welcome to navigation with TomTom
- What's in the box
- Read me first
- Positioning the device
- Installing in your car
- Switching on and off
- Setting up
- GPS reception
- Micro-SD card slot
- About MyDrive
- Setting up MyDrive
- Safety settings
- Device not starting
- Charging your device
- Sharing information with TomTom
- Safety Notice
- Take care of your navigation device
- Getting help to use your navigation device
- Planning a route
- Voice control
- The Driving View
- Advanced Lane Guidance
- Changing your route
- View map
- Map corrections
- Sounds and voices
- Settings
- About Settings
- 2D/3D settings
- Advanced settings
- Battery saving
- Brightness
- Car symbol
- Clock
- Connections
- Enable / Disable Bluetooth
- Enable / Disable flight mode
- Favourites
- GPS status
- Home location
- Keyboard
- Language
- Make your own menu
- Manage POIs
- Map colours
- Map corrections
- Me and my device
- Operate left-handed / Operate right handed
- Phones
- Reset factory settings
- Route planning
- Safety settings
- Show POI on map
- Speaker
- Start up
- Status bar
- Switch map
- Turn off voice guidance / Turn on voice guidance
- Units
- Use night colours / Use day colours
- Vehicle and routes
- Voices
- Voice control
- Volume
- Points of Interest
- Help
- Hands-free calling
- Favourites
- Traffic
- Speed Cameras
- About Speed Cameras
- Speed camera warnings
- Changing the way you are warned
- Speed camera symbols
- Updating locations for cameras and alerts
- Report button
- Reporting a new speed camera while on the move
- Reporting a new speed camera while at home
- Reporting incorrect camera alerts
- Types of speed camera you can report
- Average speed check camera warnings
- Speed Cameras menu
- Danger Zones
- TomTom camper and caravan products
- MyDrive
- Addendum
- Copyright notices
TomTom Start 60 User Manual
Displayed below is the user manual for Start 60 by TomTom which is a product in the Navigators category. This manual has pages.
Related Manuals
TomTom
Reference Guide
2
Contents
Welcome to navigation with TomTom 7
What's in the box 8
What's in the box ................................................................................................................................ 8
Read me first 9
Positioning the device ........................................................................................................................ 9
Installing in your car ........................................................................................................................... 9
Switching on and off ........................................................................................................................ 10
Setting up.......................................................................................................................................... 10
GPS reception ................................................................................................................................... 10
Micro-SD card slot ............................................................................................................................ 10
About MyDrive ................................................................................................................................. 10
Setting up MyDrive .......................................................................................................................... 11
Safety settings .................................................................................................................................. 11
Device not starting ........................................................................................................................... 12
Charging your device ....................................................................................................................... 12
Sharing information with TomTom ................................................................................................. 12
Safety Notice .................................................................................................................................... 12
Take care of your navigation device ............................................................................................... 12
Getting help to use your navigation device .................................................................................... 13
Planning a route 14
Planning a route................................................................................................................................ 14
Route summary ................................................................................................................................ 16
Alternative routes ............................................................................................................................. 16
Selecting a route type ...................................................................................................................... 17
Frequent destinations ....................................................................................................................... 18
Show my frequent destinations ....................................................................................................... 19
Using arrival times ............................................................................................................................ 19
Navigation menu options ................................................................................................................. 20
Planning a route in advance ............................................................................................................ 21
Viewing route information ............................................................................................................... 22
Voice control 23
Voice control - Navigate to .............................................................................................................. 24
About voice control ..................................................................................................................... 24
Using voice control ..................................................................................................................... 24
Planning a journey using your voice .......................................................................................... 25
Voice control - Drive to .................................................................................................................... 27
About voice control ..................................................................................................................... 27
Using voice control ..................................................................................................................... 27
3
Planning a journey using your voice .......................................................................................... 28
Entering addresses using your voice ......................................................................................... 30
The Driving View 31
About the Driving View .................................................................................................................... 31
The Driving View .............................................................................................................................. 31
Driving View Symbols ...................................................................................................................... 32
About replanning settings ................................................................................................................ 32
Advanced Lane Guidance 34
About lane guidance ........................................................................................................................ 34
Using lane guidance ......................................................................................................................... 34
Changing your route 36
Making changes to your route ......................................................................................................... 36
Change route menu .......................................................................................................................... 36
About waypoints .............................................................................................................................. 37
Adding the first waypoint to your route .......................................................................................... 37
Adding further waypoints to your route ......................................................................................... 38
Changing the order of waypoints .................................................................................................... 38
Deleting a waypoint .......................................................................................................................... 39
Changing notification settings for a waypoint ................................................................................ 39
Reactivating a waypoint ................................................................................................................... 39
View map 41
About viewing the map .................................................................................................................... 41
View map .......................................................................................................................................... 41
Options .............................................................................................................................................. 42
Cursor menu ..................................................................................................................................... 43
Map corrections 45
About Map Share ............................................................................................................................. 45
Correcting a map error ..................................................................................................................... 45
Types of map correction .................................................................................................................. 45
Sounds and voices 49
About sounds and voices ................................................................................................................ 49
About computer voices .................................................................................................................... 49
Selecting a voice .............................................................................................................................. 49
Changing the volume level .............................................................................................................. 49
Automatic volume control ............................................................................................................... 50
Settings 51
About Settings .................................................................................................................................. 51
4
2D/3D settings .................................................................................................................................. 51
Advanced settings ............................................................................................................................ 51
Battery saving ................................................................................................................................... 52
Brightness ......................................................................................................................................... 52
Car symbol ........................................................................................................................................ 52
Clock.................................................................................................................................................. 52
Connections ...................................................................................................................................... 52
Enable / Disable Bluetooth ............................................................................................................... 53
Enable / Disable flight mode ............................................................................................................ 53
Favourites ......................................................................................................................................... 53
GPS status......................................................................................................................................... 54
Home location .................................................................................................................................. 54
Keyboard ........................................................................................................................................... 54
Language .......................................................................................................................................... 54
Make your own menu ...................................................................................................................... 55
Manage POIs ..................................................................................................................................... 55
Map colours ...................................................................................................................................... 55
Map corrections ................................................................................................................................ 55
Me and my device ............................................................................................................................ 56
Operate left-handed / Operate right handed ................................................................................... 56
Phones .............................................................................................................................................. 56
Reset factory settings ....................................................................................................................... 56
Route planning ................................................................................................................................. 56
Safety settings .................................................................................................................................. 57
Show POI on map ............................................................................................................................ 57
Speaker ............................................................................................................................................. 58
Start up ............................................................................................................................................. 58
Status bar .......................................................................................................................................... 58
Switch map ....................................................................................................................................... 58
Turn off voice guidance / Turn on voice guidance ......................................................................... 59
Units .................................................................................................................................................. 59
Use night colours / Use day colours ............................................................................................... 59
Vehicle and routes ............................................................................................................................ 59
Voices ................................................................................................................................................ 60
Voice control ..................................................................................................................................... 60
Volume .............................................................................................................................................. 61
Points of Interest 62
About Points of Interest ................................................................................................................... 62
Creating POIs .................................................................................................................................... 62
Using POIs to plan a route ............................................................................................................... 64
Showing POIs on the map ............................................................................................................... 64
Calling a POI...................................................................................................................................... 64
Setting warnings for POIs ................................................................................................................ 65
Manage POIs ..................................................................................................................................... 65
Help 67
About getting help ............................................................................................................................ 67
Using Help to phone a local service ................................................................................................ 67
5
Help menu options ........................................................................................................................... 67
Hands-free calling 69
About hands-free calls ..................................................................................................................... 69
Connecting to your phone ............................................................................................................... 69
Making a call ..................................................................................................................................... 69
Receiving a call ................................................................................................................................. 70
Auto-answer ..................................................................................................................................... 70
Connecting more phones to your device ........................................................................................ 70
Mobile phone menu ......................................................................................................................... 70
Favourites 72
About Favourites .............................................................................................................................. 72
Creating a Favourite ......................................................................................................................... 72
Using a Favourite .............................................................................................................................. 73
Changing the name of a Favourite .................................................................................................. 74
Deleting a Favourite ......................................................................................................................... 74
Traffic 75
About RDS-TMC ............................................................................................................................... 75
Using traffic information .................................................................................................................. 75
Taking the fastest route .................................................................................................................... 76
Minimising delays............................................................................................................................. 76
Making commuting to work easier .................................................................................................. 76
Getting more information about an incident................................................................................... 77
Checking traffic incidents in your area ............................................................................................ 78
Changing traffic settings .................................................................................................................. 79
Traffic incidents ................................................................................................................................ 79
Traffic menu ...................................................................................................................................... 80
Speed Cameras 82
About Speed Cameras ..................................................................................................................... 82
Speed camera warnings .................................................................................................................. 82
Changing the way you are warned .................................................................................................. 82
Speed camera symbols.................................................................................................................... 83
Updating locations for cameras and alerts ..................................................................................... 84
Report button .................................................................................................................................... 84
Reporting a new speed camera while on the move ....................................................................... 85
Reporting a new speed camera while at home .............................................................................. 85
Reporting incorrect camera alerts ................................................................................................... 85
Types of speed camera you can report .......................................................................................... 85
Average speed check camera warnings ......................................................................................... 86
Speed Cameras menu ...................................................................................................................... 86
Danger Zones 88
About danger zones ......................................................................................................................... 88
6
Danger zone warnings ..................................................................................................................... 88
Changing the way you are warned .................................................................................................. 88
Danger zone symbols....................................................................................................................... 89
Report button .................................................................................................................................... 89
Reporting a new danger zone while on the move .......................................................................... 89
Reporting a new danger zone while at home ................................................................................. 89
Safety Alerts menu ........................................................................................................................... 89
TomTom camper and caravan products 91
About TomTom camper and caravan products ............................................................................. 91
Vehicle types .................................................................................................................................... 91
Set up your vehicle .......................................................................................................................... 92
Selecting a camper and caravan map ............................................................................................. 93
Selecting your vehicle type.............................................................................................................. 93
Show the vehicle type quick menu button ..................................................................................... 94
MyDrive 95
About MyDrive ................................................................................................................................. 95
About MyDrive Connect................................................................................................................... 95
MyTomTom account ........................................................................................................................ 95
Setting up MyDrive .......................................................................................................................... 95
Addendum 97
Copyright notices 100
7
This Reference Guide explains all you need to know about your new TomTom navigation device.
If you want a quick read of the essentials, we recommend that you read the Read me first chapter.
This covers installation, switching on, setting up and updating using MyDrive.
After that, you will probably want to look at route planning and you can read all about that in the
Planning a route chapter.
For information about what you see on the device itself, go to:
The Driving View
View map
Traffic
Speed Cameras
Tip: There are also frequently asked questions (FAQs) at tomtom.com/support. Select your
product model from the list or enter a search term.
We hope you enjoy reading about and, most importantly, using your new navigation device!
Welcome to navigation with TomTom
8
What's in the box
TomTom navigation device with removable or integrated mount
USB cable
or
USB car charger
Dashboard mount disks. Disks are included in some products and are available as accessories
for others. For more information, go to tomtom.com/accessories.
Installation poster
What's in the box
9
Positioning the device
Consider carefully where to install your TomTom navigation device in your car. The navigation
device should not block or interfere with any of the following:
Your view of the road
Any of the controls in your car
Any of your mirrors
Any airbags
When your navigation device is installed, you should be able to reach the device easily without
leaning or stretching. You can attach the device to the windscreen or you can use a Dashboard
Mount Disk to attach the mount to your dashboard. Dashboard Mount Disks are included with
some products and are available as accessories. The following diagrams show where you can
safely attach the mount.
TomTom also offers alternative mounting solutions for your TomTom navigation device. For more
information about Dashboard Mount Disks and alternative mounting solutions, go to
tomtom.com/accessories.
Installing in your car
Use the mount provided with your device to install your TomTom device in your vehicle. You can
attach your device to your windscreen or use a Dashboard Mount Disk to attach your device to
your dashboard. See the printed installation instructions included with your product for more
information. Read the instructions about positioning your device before you install your device.
To install your device, do the following:
1. Choose the best location to mount your TomTom device. The location should be as smooth as
possible.
2. If you are using the Dashboard Mounting Disk, clean the dashboard and install the disk.
3. Make sure that both the suction cup on the mount and your windscreen or disk are clean and
dry.
4. Press the suction cup of the mount firmly against your windscreen or disk.
5. Turn the rubber grip near the base of the mount in a clockwise direction until you feel it lock.
6. If your mount is not integrated into your device, place your device in the mount, making sure
that it clicks into place.
Read me first
10
7. Plug the USB car charger into the power supply on your dashboard.
8. Connect the USB cable to the car charger and your device.
Your navigation device is now installed. The next step is to switch it on and answer a few ques-
tions.
Switching on and off
To switch on your navigation device, press and hold the On/Off button until you see the start-up
screen. The first time you switch on your device, you have to hold the button down for up to 15
seconds.
Setting up
Important: Take care to select the correct language as the language you choose will be used for
all text on the screen.
When you first switch on your device, you have to answer a few questions to set up the device.
Answer the questions by tapping the screen.
GPS reception
When you first start your TomTom navigation device, the device may need a few minutes to
determine your GPS position and show your current position on the map. In future, your position
will be found much faster, usually within a few seconds.
To ensure good GPS reception, you should use your device outdoors and keep your device
upright. Large objects such as tall buildings can sometimes interfere with reception. GPS reception
can also be affected if the device is placed flat on a surface or held flat in your hand.
Micro-SD card slot
Some types of TomTom navigation devices have a micro-SD card slot that is located on the side
or on the bottom of the device.
Before you use the memory card slot, make sure that you have the latest version of the application
installed on your navigation device by connecting to MyDrive. When your device is up-to-date,
you can use a memory card as extra storage space to add extra maps to your device. Maps can be
purchased from tomtom.com.
About MyDrive
MyDrive is a web-based tool that helps you manage the contents and services of your TomTom
navigation device. You use MyDrive to get map updates as well as lots of other things.
You log in to MyDrive on the TomTom website. It is a good idea to frequently connect your
navigation device to MyDrive to ensure you always have the latest updates.
Tip: We recommend using a broadband internet connection whenever you connect your navi-
gation device to MyDrive.
11
Setting up MyDrive
To get ready to use MyDrive for the first time, do the following:
1. On your computer, open a web browser and go to tomtom.com/getstarted.
2. Click Get Started.
3. Click Download MyDrive Connect.
Follow the instructions on the screen.
4. When prompted, connect your device to your computer using the USB cable supplied with
your device, then switch your device on.
Note: Use ONLY the USB cable supplied with your device. Other USB cables may not work.
Note: You should plug the USB cable directly into a USB port on your computer and not into
a USB hub or USB port on a keyboard or monitor.
5. Enter the requested information for account creation, including your country.
When set-up is complete, a MyTomTom account is created and your navigation device is
linked to that account.
You can now access MyDrive Connect from the notification area on your desktop.
MyDrive starts automatically after the account is created.
Note: Next time you want to access MyDrive, go to tomtom.com/mydrive in a web browser.
Tip: When you connect your navigation device to your computer, MyDrive Connect tells you
if there are any updates for your device.
Safety settings
We recommend using the safety settings to make your driving as safe as possible.
These are some of the options included in the safety settings:
Show essential menu buttons while driving
Show safety reminders
Warn when driving faster than allowed
If your device supports voice control, you can also drive more safely by using voice control to
control your navigation device.
12
Device not starting
In rare cases, your TomTom navigation device may not start correctly or may stop responding to
your taps.
First, check that the battery is charged. To charge the battery, connect your device to the car
charger. It can take up to 2 hours to fully charge the battery.
If this does not solve the problem, you can reset the device. To do this, press and hold the On/Off
button until you hear the drum sound and your device restarts. This can take 30 seconds or more.
Charging your device
The battery in your TomTom navigation device charges when you connect it to the car charger or
to your computer.
Important: You should plug the USB connector directly into a USB port on your computer and not
into a USB hub or USB port on a keyboard or monitor.
Sharing information with TomTom
When you first start navigating or perform a reset, your device asks for permission to collect some
information about your use of the navigation device. The information is stored on the device until
we retrieve it. We use it anonymously to improve our products and services.
You can change whether you share this information with us at any time by doing the following:
1. In the Main Menu, tap Settings.
2. Tap Me and my device.
3. Tap My information.
4. Tap No to stop sharing or tap Yes to start sharing.
For more information, see our privacy policy at tomtom.com/privacy.
Safety Notice
Some navigation devices contain a GSM/GPRS module which can interfere with electrical devices
such as cardiac pacemakers, hearing aids and aviation equipment.
Interference with these devices may endanger the health or life of you or others.
If your device includes a GSM/GPRS module, do not use it near unprotected electrical units or in
areas where the use of mobile telephones is prohibited, such as hospitals and aircraft.
Take care of your navigation device
It is important to take care of your device:
Do not open the casing of your device under any circumstances. Doing so may be dangerous
and will invalidate the warranty.
Wipe or dry the screen of your device using a soft cloth. Do not use any liquid cleaners.
14
Planning a route
Important: In the interest of safety and to reduce distractions while you are driving, you should
always plan a route before you start driving.
Important: If you are using a TomTom camper and caravan product, before planning a route you
should set up your device for your vehicle.
To plan a route on your TomTom device, do the following:
1. Tap the screen to open the Main Menu.
2. Tap Navigate to or Drive to.
3. Tap Address.
You can change the country or state setting by tapping the flag before you select a city.
4. Enter the town or city name, or the postcode.
Tip: If your device supports voice control, instead of typing the address, tap the microphone
button to enter the address by speaking to your TomTom device.
Towns with similar names are shown in the list while you type.
When the correct city or town appears in the list, tap the name to select the destination.
Planning a route
15
5. Enter the street name.
Streets with similar names are shown in the list while you type.
When the correct street name appears in the list, tap the name to select the destination.
6. Enter the house number, then tap Done.
7. The location is shown on the map. Tap Select to continue or tap Back to enter another ad-
dress.
Important: If you are planning a caravan or camper route and no specific route can be found,
you are asked if you want to use a car route instead. If you use a car route pay special atten-
tion to any route restrictions while driving.
Tip: If you want your final destination to be a car park, tap Car park and select a location
from the list of car parks close to your general destination.
16
8. When the new route is shown, tap Done.
For more information about the route, tap Details.
To change your route, for example, to travel via a particular location or to select a new desti-
nation, tap Change route.
Your device starts to guide you to your destination, using spoken instructions and on-screen
directions.
Route summary
The route summary shows an overview of your route, the remaining distance to your destination
and the remaining estimated journey time.
To view the route summary, tap the right-hand panel on the status bar in the Driving view or tap
View route in the Main Menu and then tap Show route summary.
If you have TomTom Traffic or an RDS-TMC receiver, the route summary also shows traffic
information about delays on your route.
Note: To use a TomTom traffic information service, you may need a subscription or a receiver.
Traffic services are not supported in all countries or regions. For more information, visit
tomtom.com/services.
Alternative routes
Note: This feature is not available on all TomTom navigation devices.
17
Your TomTom device helps you reach your destination as quickly as possible by showing you a
faster alternative route when one is available.
To take the alternative route, tap the balloon at the top of the screen. If you don't want to follow
the alternative route, keep driving to continue to receive instructions for your original route.
Tip: The alternative route disappears when it is no longer faster than your original route or it is
too late for you to choose it.
To change how you are asked about alternative routes, tap Settings and then Route planning. Tap
Next until you reach Replanning settings.
Selecting a route type
Every time you plan a route, you can choose to be asked about the type of route you want to plan.
To do this, tap Settings followed by Route planning, then Route types. Tap Ask me every time I
plan.
If you are using a TomTom camper and caravan product, to choose the type of route you have to
set your vehicle type to Car. Tap Settings followed by Vehicle and routes, then Vehicle and route
types. Select Car as your vehicle type, then tap Ask me every time I plan.
18
Note: You can only choose to be asked about the type of route when you select a car as your
vehicle.
The types of route you can choose from are as follows:
Fastest route - the route which takes the least time.
Eco route - the most fuel-efficient route for your journey.
Shortest route - the shortest distance between the locations you set. This may not be the
quickest route, especially if the shortest route is through a town or city.
Walking route - a route designed for making the journey on foot.
Bicycle route - a route designed for making the journey on a bicycle.
Limited speed - a route based on a maximum speed. When you choose this type of route,
you enter a maximum speed. The route and estimated time of arrival are then planned
based on the speed that you entered.
Tap Next. If you selected Fastest route, you have to choose if you want to always avoid motor-
ways.
Frequent destinations
If you often make trips to the same destinations, you can set your TomTom device to ask if you
want to plan a route to one of these locations every time the device starts. This is faster than
planning a route in the normal way.
19
Show my frequent destinations
You can set your TomTom device to ask if you want to plan a route to one of your frequently
visited destinations every time the device starts.
To change this setting, do the following:
1. Tap Start up in the Settings menu and then select Ask for a destination.
2. Tap Yes, then tap Yes again to begin entering information about the destination.
3. Select a symbol for the destination and tap Done to set the symbol, then tap Yes.
Tip: To add new destinations, select one of the numbered symbols and enter a name for the
new destination button.
4. Tap Yes and if required enter a new name, then tap Done.
5. Enter the address details in the same way you enter an address when planning a route, then
tap Done.
6. If you want to set more destinations, repeat the steps above. Otherwise, tap Done.
7. You are asked if you want to change the start-up image.
8. If you want to change the image, tap Yes then follow the instructions shown on the screen.
Otherwise, tap No.
Every time your device starts, you are asked if you want to plan a route. If you tap Cancel, the
Driving View opens.
Using arrival times
You can set your TomTom device to ask you if you need to arrive at a particular time when you
plan a route.
Status bar
Tap Status bar in the Settings menu, to enable or disable arrival time
notifications.
To enable arrival time notifications, select Leeway.
After planning a route, tap YES to enter a preferred arrival time.
Your device calculates your arrival time and shows you whether you will arrive on time.
You can also use this information to work out when you need to leave. If your device shows that
you will arrive 30 minutes early, you can wait and leave in 30 minutes time, rather than arrive
early.
Your arrival time is constantly recalculated during your journey. The status bar shows whether you
will arrive on time or if you are going to be late, as shown below:
You will arrive 55 minutes before the arrival time you entered.
If the estimated arrival time is more than five minutes before the time you
entered, it is shown in green.
You will arrive 3 minutes before the arrival time you entered.
If the estimated arrival time is less than 5 minutes before the time you
entered, it is shown in yellow.
20
You will arrive 19 minutes late.
If the estimated arrival time is later than the time you entered, it is shown
in red.
Navigation menu options
When you tap Navigate to or Drive to, you can set your destination in many ways, not just by
entering the address. The other options are listed below:
Home
Tap this button to navigate to your Home location.
You will probably use this button more than any other.
Favourite
Tap this button to select a Favourite as your destination.
Address
Tap this button to enter an address as your destination.
Recent destination
Tap this button to select your destination from a list of places you have
recently used as destinations.
Point of Interest
Tap this button to navigate to a Point of Interest (POI).
Spoken address
On some devices you can enter an address using speech. See Voice
control.
Point on map
Tap this button to select a point on the map as your destination using the
map browser.
Latitude Longitude
Tap this button to enter a destination using latitude and longitude values.
21
Position of last
stop
Tap this button to select your last recorded position as your destination.
Local search
Tap this button to use Local Search with TomTom Places to help you find
shops and businesses in and around your current location.
You can choose to search for shops and businesses near you, near your
destination, near any other destination or in a city.
For example, if you are looking for a swimming pool near your current
location, enter 'swimming pool' and choose the best search result.
Planning a route in advance
You can use your TomTom device to plan a route in advance, selecting your starting point and
your destination.
Here are some more reasons to plan a route in advance:
Find out how long a journey is going to take before you start.
You can also compare journey times for the same route at different times of the day or on
different days of the week. Your device uses IQ Routes when planning a route. IQ Routes cal-
culates routes based on the real average speeds measured on roads.
Study the route of a journey you are planning.
Check a route for someone who is coming to visit you and then explain the route to them in
detail.
To plan a route in advance, follow these steps:
1. Tap the screen to bring up the Main menu.
2. Tap the arrow button to move to the next menu screen and tap Plan route.
This button is shown while there is no planned route on your TomTom device.
3. Select the starting point for your journey in the same way that you would select your destina-
tion.
4. Set the destination for your journey.
5. If Route planning settings are set to Ask me every time I plan, select the type of route you
want to plan:
Fastest route - the route which takes the least time.
Eco route - the most fuel-efficient route for your journey.
Shortest route - the shortest distance between the locations you set. This may not be the
quickest route, especially if the shortest route is through a town or city.
Avoid motorways - a route which avoids motorways.
Walking route - a route designed for making the journey on foot.
Bicycle route - a route designed for making the journey on a bicycle.
6. Choose the date and time that you will make the journey you are planning.
22
Your device uses IQ Routes to work out the best possible route at that time. This is useful to see
how long a journey takes at different times of the day or on different days of the week.
Your navigation device plans the route between the two locations you selected.
Viewing route information
You can access these options for the route you last planned by tapping View route in the Main
Menu or the Details button on the route summary screen.
You can then select from the following options:
Show instructions
Tap this button for a list of all the turn instructions on the route.
This is very useful if you need to explain a route to someone else.
Show map of route
Tap this button to see an overview of the route using the map browser.
Show route demo
Tap this button to watch a demo of the journey. You can interrupt the
demo at any time by tapping the screen.
Show route
summary
Tap this button to open the route summary screen.
Show destination
Tap this button to see a preview of your destination.
You can navigate to a car park near your destination, and view any
available information about your destination, for example, the phone
number.
Show traffic on
route
Tap this button to see all the traffic incidents on your route.
Note: This button is only shown if your device has either a traffic
subscription or an RDS-TMC Receiver. Traffic information is not avail-
able in all countries or regions. For more information about TomTom
traffic information services, go to tomtom.com/services.
23
Note: Voice control is not supported on all devices or in all languages.
Voice control works in different ways depending on your device type.
Navigate to
If you see the button Navigate to in the Main Menu on your device, read these topics about Voice
Control:
Voice control - Navigate to
Drive to
If you see the button Drive to in the Main Menu on your device, read these topics about Voice
Control:
Voice control - Drive to
Voice control
24
Voice control - Navigate to
About voice control
Note: Voice control is not supported on all devices or in all languages.
Instead of tapping the screen to control your TomTom device, you can use your voice to control
your device.
For example, to increase the volume on your device, you can say "Increase volume".
To view the list of available commands, tap Help in the Main menu, tap Product manuals and then
tap What can I say?
Important: Voice control requires a computer voice. When there is no computer voice installed
and selected on your TomTom device, this feature is not available.
To select a computer voice, tap Voices in the Settings menu, then tap Change voice and select a
computer voice.
Using voice control
To switch on voice control and show the button in the Driving view, tap Voice control in the
Settings menu and select Enable voice control.
To switch off voice control and remove the button from the Driving view, tap Voice control in the
Settings menu and select Disable voice control.
The following example shows how to use voice control to plan a journey to your Home address:
1. Tap the microphone button in the Driving view to turn on the microphone.
You see a screen with examples of commands you can say.
Tap What can I say? to see a full list of commands you can say. Alternatively, tap Settings in
the Main menu, tap Voice control and then tap What can I say?
2. When you hear the beep, say a command of your choice. For example, you can say "Navigate
home". Your device is only ready to listen after your hear the beep.
While you are speaking the microphone monitor shows how well the device can hear your
voice:
A green bar means the device can hear your voice.
A red bar means your voice is too loud for the device to recognise individual words.
A grey bar means your voice is too quiet for the device to recognise individual words.
For some phrases, your device asks for confirmation.
Tip: For the best recognition of what you say, speak normally without trying to articulate
words in an unnatural way. If there is excessive road noise, for example, you may need to
speak in the direction of the microphone.
3. If the command is correct, say "Yes."
If the command is incorrect, say "No" and repeat the command after you hear the prompt and
beep again.
25
Your device plans a route from your current location to your destination.
Tip: To stop your device from listening out for further commands, say "Cancel". To go back one
step, say "Back".
Planning a journey using your voice
Important: In the interest of safety and to reduce distractions while you are driving, you should
always plan a route before you start driving.
Note: It's not possible to plan a route using your voice for all maps in all countries, or in all
languages.
To plan a route to an address using speech, do the following:
1. Tap the voice control button in the Driving view.
2. When you hear the beep, say, "Navigate to address".
3. Say the name of the town.
Your device shows a list of towns which sound similar to what you said and tells you which
town is at the top of the list.
If the town you hear is the same as the town you requested then say, "Done" or "OK" or "Yes"
or "One" or tap the town at the top of the list.
If the town you hear is incorrect, but the correct town is in the list, say the number next to the
correct town or tap the name of the town.
For example, if the correct city is Rotterdam and this town is shown at the third item in the list,
you can say, "Three" or tap the name, Rotterdam.
If the name is not in the list, then say "Back" or "No" or tap Back to return to the previous
screen and say the town again when you hear the beep.
4. Say the streetname.
Your device shows a list of streetnames which sound similar to what you said and tells you
which streetname is at the top of the list.
26
If the streetname you hear is the same as the streetname you requested then say, "Done" or
"OK" or "Yes" or "One" or tap the streetname at the top of the list.
Tip: Different locations may have the same name, such as a road that spans multiple post-
codes. When this happens you need to look at the screen and tap the correct location.
If the street name you hear is incorrect, but the correct streetname is in the list, say the num-
ber next to the correct streetname or tap the streetname in the list.
If the streetname is not shown in the list, say "Back" or "No" or tap Back to return to the previ-
ous screen and then say the streetname again when you hear the beep.
5. Say the house number.
Important: Numbers need to be spoken in the same language as the button names and
menus on your device.
Numbers should be pronounced in the same way you normally say a number, in one contin-
uous sentence. So 357 is pronounced, "Three hundred and fifty seven."
If the number is shown correctly then say, "Done" or "OK" or tap the keyboard to enter the
number.
If the number is shown incorrectly then say, "Back" or "No" or tap the Backspace key and re-
peat the number.
Tip: If you say, "Back" when there are no numbers on the screen, your device will return you
to the previous screen.
When the number is shown correctly say, "Done" or "OK." Alternatively, enter the number by
tapping the screen.
6. When the route has been calculated and the route summary is shown, tap Done.
Your device starts to guide you to your destination, using spoken instructions and onscreen
directions.
Tip: In addition to planning a route using Voice control, you can tap Navigate to in the Main
menu and then tap Spoken Address. Alternatively you can tap the button at the base of the
keyboard during address entry. When the button is grey, you cannot use speech to enter an
address.
27
Voice control - Drive to
About voice control
Note: Voice control is not supported on all devices or in all languages.
Instead of tapping the screen to control your TomTom device, you can use your voice to control
your device.
For example, to increase the volume on your device, you can say "Increase volume" or "Volume
50%".
To view the list of available commands, tap Help in the Main menu, tap Product manuals and then
tap What to say.
Important: Voice control requires a computer voice. When there is no computer voice installed
and selected on your TomTom device, this feature is not available.
To select a computer voice, tap Voices in the Settings menu, then tap Change voice and select a
computer voice.
Using voice control
Voice control is switched on by default if it is supported by your chosen language.
To switch off voice control and remove the button from the Driving view, tap Voice control in the
Settings menu and select Disable voice control.
The following example shows how to use voice control to plan a journey to your Home address:
1. Tap the microphone button in the Driving view to turn on the microphone.
You see a screen with examples of commands you can say.
Tap What to say to see a full list of commands you can say. Alternatively, tap Settings in the
Main menu, tap Voice control and then tap What to say.
2. When you hear "Say a command" followed by a beep, say a command of your choice. For
example, you can say "Drive home". Your device is only ready to listen after your hear the
beep.
While you are speaking the microphone monitor shows how well the device can hear your
voice:
A green bar means the device can hear your voice.
A red bar means your voice is too loud for the device to recognise
individual words.
A grey bar means your voice is too quiet for the device to recognise
individual words.
For some phrases, your device repeats what you say and asks for confirmation.
28
Tip: For the best recognition of what you say, speak normally without trying to articulate
words in an unnatural way. If there is excessive road noise, for example, you may need to
speak in the direction of the microphone.
3. If the command is correct, say "Yes."
If the command is incorrect, say "No" and repeat the command after you hear the prompt and
beep again.
Your device plans a route from your current location to your destination.
Tip: To stop your device from listening out for further commands, say "Cancel". To go back one
step, say "Back".
Planning a journey using your voice
Important: In the interest of safety and to reduce distractions while you are driving, you should
always plan a route before you start driving.
Note: It's not possible to plan a route using your voice for all maps in all countries, or in all
languages.
To plan a route to an address using speech, do the following:
1. Tap the voice control button in the Driving view.
2. When you hear the beep, say, "Navigate to address" or "Drive to address".
Tip: Your device has either Navigate to or Drive to on the button in the Main Menu. When
planning a route to an address using speech, say "Navigate to address" if the button shows
Navigate to or "Drive to address" if the button shows Drive to.
3. Say the name of the town.
Your device shows a list of towns which sound similar to what you said and tells you which
town is at the top of the list.
If the town you hear is the same as the town you requested then say, "Done" or "OK" or "Yes"
or "One" or tap the town at the top of the list.
29
If the town you hear is incorrect, but the correct town is in the list, say the number next to the
correct town or tap the name of the town.
For example, if the correct city is Rotterdam and this town is shown at the third item in the list,
you can say, "Three" or tap the name, Rotterdam.
If the name is not in the list, then say "Back" or "No" or tap Back to return to the previous
screen and say the town again when you hear the beep.
4. Say the streetname.
Your device shows a list of streetnames which sound similar to what you said and tells you
which streetname is at the top of the list.
If the streetname you hear is the same as the streetname you requested then say, "Done" or
"OK" or "Yes" or "One" or tap the streetname at the top of the list.
Tip: Different locations may have the same name, such as a road that spans multiple post-
codes. When this happens you need to look at the screen and tap the correct location.
If the street name you hear is incorrect, but the correct streetname is in the list, say the num-
ber next to the correct streetname or tap the streetname in the list.
If the streetname is not shown in the list, say "Back" or "No" or tap Back to return to the previ-
ous screen and then say the streetname again when you hear the beep.
5. Say the house number.
Important: Numbers need to be spoken in the same language as the button names and
menus on your device.
Numbers should be pronounced in the same way you normally say a number, in one contin-
uous sentence. So 357 is pronounced, "Three hundred and fifty seven."
If the number is shown correctly then say, "Done" or "OK" or tap the keyboard to enter the
number.
If the number is shown incorrectly then say, "Back" or "No" or tap the Backspace key and re-
peat the number.
Tip: If you say, "Back" when there are no numbers on the screen, your device will return you
to the previous screen.
When the number is shown correctly say, "Done" or "OK." Alternatively, enter the number by
tapping the screen.
6. When the route has been calculated and the route summary is shown, tap Done.
30
Your device starts to guide you to your destination, using spoken instructions and onscreen
directions.
Entering addresses using your voice
Important: In the interest of safety and to reduce distractions while you are driving, you should
always plan a route before you start driving.
Even if you don't use voice control to start planning a journey, you can still use your voice to enter
the address.
To start planning a journey tap Navigate to or Drive to in the Main menu, then tap Address.
To enter the destination using your voice, tap one of the following buttons:
Spoken address
Tap this button to enter an address entirely using speech.
Spoken address helps you to enter information without tapping the
screen.
This option recognises the following spoken terms:
Commands: Yes, No, Back, Done, OK, Crossing.
Streetnames.
Cities and towns and their centres.
Favourites and POIs.
Plan alternative route, Recalculate original, Avoid roadblock, Mini-
mise delays, Clear route, Travel via... and Recent destination.
Tap this button at the base of the keyboard to use speech to enter an
address. When the button is grey, you cannot use speech to enter an
address.
This button is available for the following types of destination:
City centre - to select a city or town centre.
Street and house number - to select an address.
Crossing or intersection - to select the point where two streets meet.
Tips
Your device recognises places and streetnames when they are spoken in the local language
using local pronunciation.
Spoken address entry is not possible for postcodes which must be entered using the keyboard.
Spoken address entry is not available for all maps in all countries.
31
About the Driving View
When your TomTom navigation device starts for the first time, you are shown the Driving View
along with detailed information about your current position.
Tap the centre of the screen at any time to open the Main Menu.
You can choose the screen shown when you switch on your device by tapping Settings in the
Main Menu, then tapping Start up.
The Driving View
1. Zoom button - tap the magnifying glass to show buttons for zooming in and out.
2. Quick menu - to enable the quick menu, tap Make your own menu (page 55) in the Settings
menu. If there are only one or two buttons in your menu, both buttons are shown in the Driv-
ing view.
3. Your current position.
4. Road sign information or the next street name.
The Driving View
32
5. Traffic sidebar. Tap the sidebar to see details of traffic incidents on your route.
The traffic sidebar is only shown if your device has either a Traffic subscription or an
RDS-TMC Receiver connected. Traffic information is not available in all countries or regions.
6. Battery level indicator.
7. Microphone button for voice control.
Note: Voice control is not supported on all devices or in all languages.
8. The time, your current speed and the speed limit, if known. To see the difference between
your preferred arrival time and your estimated arrival time, check the Leeway checkbox in the
Status bar settings.
Tap this part of the status bar to switch between a 3D map and a 2D map.
9. The name of the street you are on.
10. Navigation instruction for the road ahead and the distance to next instruction. If the second
instruction is less that 150m after the first instruction, you see it shown immediately instead of
the distance.
Tap this part of the status bar to repeat the last voice instruction and to change the volume.
You can also tap here to mute the sound.
11. The remaining journey time, the remaining distance and your estimated arrival time.
Tap this part of the status bar to open the Route Summary screen.
To change the information shown in the status bar, tap Status bar in the Settings menu.
Driving View Symbols
Sound muted - this symbol is shown when the sound has been muted.
To turn the sound back on, tap the middle panel in the status bar.
Battery - this symbol is shown when the battery level is low. When you
see this symbol, you should charge your navigation device immediately.
Connected to computer - this symbol is shown when your navigation
device is connected to your computer.
Mobile phone not connected - this symbol is shown when the selected
mobile phone is not connected to your device. You must have already
established a connection to this phone.
About replanning settings
Your TomTom device helps you reach your destination as quickly as possible by showing you a
faster alternative route when one is available.
To change how you are asked about alternative routes, tap Settings and then Route planning. Tap
Next until you reach Replanning settings.
Note: This setting is only available if your device has either a traffic subscription or an
RDS-TMC Receiver. Traffic information is not available in all countries or regions. For more
information about TomTom traffic information services, go to tomtom.com/services.
Set whether you want your TomTom device to replan the current route if a faster route is found
while you are driving. This is useful if traffic builds up or clears, further ahead on your route.
Choose from the following settings:
33
Always switch to that route - select this option to receive no messages when a faster route
is found. The current route is automatically re-calculated to be the fastest one.
Ask me if I want that route - select this option to be asked if you want to take the new route.
When asked if you wish to take the alternative route, tap Yes to have the current route
re-calculated as the fastest one. Tap No if you don't want to take alternative route. If you
change your mind, tap the balloon at the top of the screen to take the alternative route.
Tap Info to see a summary of both the original and alternative routes. You can then tap Done
to take the fastest route or Current route to remain on your original route.
Don't ask, just show me - select this option to receive no messages and simply be shown the
new route on the screen. You can then tap the balloon if you decide you want to use the al-
ternative route.
34
About lane guidance
Note: Lane guidance is not available for all junctions or in all countries.
Your TomTom navigation device helps you prepare for motorway exits and junctions by showing
the correct driving lane for your planned route.
As you approach an exit or junction, the lane you need is shown on the screen.
Using lane guidance
There are two types of lane guidance:
Lane images
To turn lane images off, tap Settings in the Main menu, then tap Advanced settings. Clear the
checkbox for Show lane images.
Tip: Tap anywhere on the screen to return to the Driving View.
Instructions in the status bar
Advanced Lane Guidance
35
Tip: If no lane guidance is shown in the status bar and all lanes are highlighted, you can use
any lane.
36
Making changes to your route
After you plan a route, you may want to change the route or even the destination. There are
various ways to change your route without the need to completely replan the entire journey.
To change the current route, tap Change route in the Main menu:
Change route
Tap this button to change the current route.
This button is only shown while there is a planned route on your device.
Change route menu
To change the current route or your destination, tap one of the following buttons:
Calculate alterna-
tive
Tap this button to find an alternative to the current route.
This button is only shown while there is a planned route on your
TomTom device.
This is a simple way to search for a different route to your current
destination.
Your device calculates a new route from your current location, to reach
your destination using completely different roads.
The new route is shown next to the original route so that you can select
the route you want to use.
Avoid roadblock
Tap this button while driving on a planned route, to avoid a roadblock or
traffic congestion on the road ahead.
Your device will suggest a new route which avoids the roads on your
current route for the selected distance.
If the roadblock or traffic congestion suddenly clears, tap Recalculate
route to replan your original route.
Important: Be aware that when a new route is calculated, you might
immediately be asked to turn off the current road.
Minimise delays
Tap this button to avoid traffic delays on a planned route.
It is not always possible to avoid all traffic delays. Though your device
continuously checks for delays on your route, you can tap this button to
manually start a check. Your device then calculates the best route to
avoid all or most of the delays.
Note: This button is only shown if your device has either a traffic
subscription or an RDS-TMC Receiver. Traffic information is not avail-
able in all countries or regions. For more information about TomTom
Changing your route
37
traffic information services, go to tomtom.com/services.
Change destination
Tap this button to change the current destination.
When you change the destination, you are shown the same options and
asked to enter the new address in the same way as when you plan a new
route.
Avoid part of route
Tap this button to avoid part of the current route.
You are shown a list of the street names on your route. When you tap
one of the street names, your device calculates a detour to avoid the
selected street. The route summary shows both the new route and your
original route. Tap the panel on the right to select one of the routes and
then tap Done.
If you do not want to use either of the routes shown in the route sum-
mary, tap Change route to find another way to change your route.
Travel via...
Tap this button to change your route by selecting a location you want to
travel past, maybe so you can meet someone on the way.
When you select a location to travel past, you are shown the same
options and asked to enter the new address in the same way as when
you plan a new route.
Your device calculates the route to your destination via the selected
location.
The selected location is shown on the map using a marker.
You receive a warning when you reach your destination and when you
travel past a marked location.
About waypoints
Note: This feature is not available on all TomTom navigation devices.
You can choose to use waypoints for any of the following reasons:
You want to travel along a certain road or through a certain area on the way to your destina-
tion.
You want to make stops before reaching your final destination.
Your route can include the following types of way points:
Waypoints with notification - a waypoint that you are likely to want to stop and get out at, for
example, a POI, a petrol station or a friend's house. You are notified when nearing and arriving
at the waypoint with voice instructions or a message.
Waypoints without notification - a waypoint that you are using to help guide your route, for
example, you want to travel from Amsterdam to Rotterdam using a certain highway. You are
not notified when nearing the waypoint.
Adding the first waypoint to your route
To add the first waypoint to your route, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Change route.
38
3. Tap Travel via.
Tip: You can also tap View map and then tap Travel via in the cursor menu. If your device
supports Voice control, you also speak commands to add waypoints.
4. Choose the location for your waypoint from a choice of Home, Favourite, Address, Recent
destination, POI, point on map, longitude/latitude, position of last stop or you can perform a
search.
On the route summary screen, a message confirms that the route is being recalculated to in-
clude the waypoint. In the Change route menu, the Travel via button changes to show that you
now have one waypoint on your current route.
Note: All waypoints are added initially as waypoints with notification. The maximum number
of waypoints you can add is three.
Adding further waypoints to your route
To add more waypoints to your route after the first one has been added, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Change route.
3. Tap Travel via.
Tip: If your device supports Voice control, you also speak commands to add waypoints.
4. Tap Add.
5. Choose the location for your waypoint from a choice of Home, Favourite, Address, Recent
destination, POI, point on map, latitude/longitude, position of last stop or you can perform a
search.
A message tells you where in the list of waypoints the new one has been inserted.
6. Tap Done.
On the route summary screen, a message confirms that the route is being recalculated to in-
clude your waypoints.
7. Repeat to add more waypoints.
On the Change route menu, the Travel via button changes to show that you now have several
waypoints on your current route.
Note: All waypoints are added initially as waypoints with notification.
Changing the order of waypoints
Waypoints are automatically added in an optimised order but you can still change the order
manually if you need to. To change the order of waypoints, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Change route.
3. Tap Travel via.
You see a list of your waypoints.
4. Tap the waypoint you want to move up or down.
You see a screen with the name of your waypoint at the top.
5. Tap Move up or Move down.
39
Your waypoint changes its position in the list and you are immediately returned to your list of
waypoints.
Tip: You cannot move an unvisited waypoint into a list of already visited waypoints.
Deleting a waypoint
To delete a waypoint, do the following:
1. Tap the screen to bring up the Main Menu.
2. Tap Change route.
3. Tap Travel via.
You see a list of your waypoints.
4. Tap the waypoint you want to delete.
You see a screen with the name of your waypoint at the top.
5. Tap Delete.
Your waypoint is deleted and you are immediately returned to your list of waypoints.
Changing notification settings for a waypoint
If a waypoint has notification switched on, you see an icon next to it in your list of waypoints. To
switch notification on or off for a waypoint, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Change route.
3. Tap Travel via.
You see a list of your waypoints.
4. Tap the waypoint that you want to change the notification setting for.
You see a screen with the name of your waypoint at the top.
5. Tap Switch on/off notification.
The notification setting changes for your waypoint and you are immediately returned to your
list of waypoints.
Tip: If a waypoint has already been visited, you cannot switch notification on or off.
Reactivating a waypoint
Note: You can only reactivate a waypoint that has already been visited. Visited waypoints are
greyed out.
To reactivate a waypoint, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Change route.
3. Tap Travel via.
You see a list of your waypoints.
4. Tap the visited waypoint that you want to reactivate.
You see a screen with the name of your waypoint at the top.
5. Tap Reactivate.
40
The waypoint is deleted and reinserted into the list of waypoints that haven't yet been visited.
41
About viewing the map
You can view the map in the same way as you might look at a traditional paper map. The map
shows your current location and many other locations such as Favourites and POIs.
To view the map in this way, tap View map or View route in the Main menu.
You view different locations on the map by moving the map across the screen. To move the map,
touch the screen and drag your finger across the screen. If your device supports gestures, you can
also zoom in and out by touching the screen with your thumb and forefinger and sliding them
together and apart.
To select a location on the map, tap the location on the map. The cursor highlights the location
and displays useful information about the location in an information panel. Tap the information
panel to create a Favourite or plan a route to that location.
View map
1. The scale bar
View map
42
2. Traffic - current traffic incidents. Use the Options button to select whether traffic information is
shown on the map. When traffic information is shown on the map, POIs and Favourites are not
shown.
Note: To use a TomTom traffic information service, you may need a subscription or a re-
ceiver. Traffic services are not supported in all countries or regions. For more information,
visit tomtom.com/services.
3. Marker
A marker shows the distance to a location. Markers are coloured as follows:
Blue - points to your current location. This marker is grey if you lose your GPS signal.
Yellow - points to your home location.
Red - points to your destination.
Tap a marker to centre the map on the location pointed to by the marker.
You can also set your own marker. Tap the cursor button, then tap Set marker position to
place a green marker at the cursor position.
To turn markers off, tap Options, then Advanced and clear the Markers checkbox.
4. Options button
5. The cursor with street name balloon
Tap the button in the street name balloon to open the cursor menu. You can navigate to the
cursor position, make a Favourite of the cursor position, or find a Point of Interest near the
cursor position.
6. The Find button
Tap this button to find specific addresses, favourites or Points of Interest.
7. The zoom bar
Zoom in and out by moving the slider.
Options
Tap the Options button to set the information shown on the map and show the following infor-
mation:
Traffic - select this option to show traffic information on the map. When traffic information is
shown, POIs and Favourites are not shown.
Note: To use a TomTom traffic information service, you may need a subscription or a re-
ceiver. Traffic services are not supported in all countries or regions. For more information,
visit tomtom.com/services.
Names - select this option to show street and city names on the map.
Points of interest - select this option to show POIs on the map. Tap Choose POIs to choose
which POI categories are shown on the map.
Images - select this option to show satellite images of the area being viewed. Satellite images
are not available in every map or for every location on the map.
Favourites - select this option to show your Favourites on the map.
Tap Advanced to show or hide the following information:
Markers - select this option to enable markers. Markers point to your current location (blue),
your home location (orange) and your destination (red). The marker shows the distance to the
location.
43
Tap a marker to centre the map on the location which the marker is pointing to.
To create your own marker, tap the cursor button. Then tap Set marker position to place a
green marker at the cursor position.
To disable markers, tap Options, then tap Advanced and unselect Markers.
Coordinates - select this option to show GPS coordinates in the lower left corner of the map.
Cursor menu
The cursor can be used to do more than highlight a location on the map.
Position the cursor on a location on the map, then tap the arrow and then tap one of the following
buttons:
Navigate there
Tap this button to plan a route to the cursor position on the map.
View location
Tap this button to view information about the location on the map such
as the address.
Set marker posi-
tion
Tap this button to create your own green marker and place it at the
cursor position.
If a green marker exists, this button changes to Delete marker.
Find POI nearby
Tap this button to find a POI near the cursor position on the map.
For example, if the cursor currently highlights a restaurant location on
the map, you can search for a nearby parking garage.
Correct location
Tap this button to make a map correction for the cursor position on the
map.
You can make the correction only on your own map or you can share the
correction with the TomTom Map Share community.
Add as Favourite
Tap this button to create a Favourite at the cursor position on the map.
Add as POI
Tap this button to create a POI at the cursor position on the map.
44
Travel via...
Tap this button to travel via the cursor position on the map as part of
your current route. Your destination remains the same as before, but
your route now includes this location.
This button is only available while there is a planned route.
Centre on map
Tap this button to centre the map on the cursor position.
Call...
Note: Hands-free calling is not supported on all devices.
Tap this button to call the location at the cursor position.
This button is only available if your TomTom device has the phone
number for the location.
The phone numbers for many POIs are available on your TomTom
device.
You can also call phone numbers of your own POIs.
45
About Map Share
Map Share helps you correct map errors. You can correct several types of map error.
To make corrections to your own map, tap Map corrections in the Settings menu.
Note: Map Share is not available in all regions. For more information, go to
tomtom.com/mapshare.
Correcting a map error
Important: For safety reasons, do not enter the full details of a map correction while you are
driving. Mark the location of the map error instead and enter the full details later.
To correct a map error, do the following:
1. Tap Map corrections in the Settings menu.
2. Tap Correct a map error.
3. Select the type of map correction you want to apply.
4. Select how you want to select the location.
5. Select the location. Then tap Done.
6. Enter the details of the correction. Then tap Done.
7. Select whether the correction is temporary or permanent.
8. Tap Continue.
The correction is saved.
Types of map correction
To make a correction to your map, tap Map corrections in the Settings menu, then tap Correct a
map error. There are several types of map correction available.
(Un)block street
Tap this button to block or unblock a street. You can block or unblock the
street in one or both directions.
For example, to correct a street near to your current location, do the
following:
1. Tap (Un)block street.
2. Tap Near you to select a street near your current location. Alterna-
tively, you can select a street by name, a street near your Home loca-
Map corrections
46
tion or a street on the map.
3. Select the street or section of a street you want to correct by tapping
it on the map.
The street you select is highlighted and the cursor shows the name
of the street.
4. Tap Done.
Your device shows the street and whether the traffic is blocked or
allowed in each direction.
5. Tap one of the direction buttons to block or unblock the flow of traffic
in that direction.
6. Tap Done.
Reverse traffic
direction
Tap this button to correct the traffic direction of a one-way street, where
the direction of traffic is different from the direction shown on your map.
Note: Reverse traffic direction only works for one-way streets. If you
select a two-way street you will be given the chance to block/unblock
the street rather than changing the direction.
Edit street name
Tap this button to change the name of a street on your map.
For example, to rename a street near to your current location:
1. Tap Edit street name.
2. Tap Near you.
3. Select the street or section of a street you want to correct by tapping
it on the map.
The street you select is highlighted and the cursor shows the name
of the street.
4. Tap Done.
Tip: If the highlighted section is not correct, tap Edit to change indi-
vidual road sections.
5. Type the correct street name.
6. Tap Continue.
47
Change turn
restrictions
Tap this button to change and report incorrect road turn restrictions.
Change road speed
Tap this button to change and report the road speed limit.
Add or remove
roundabout
Tap this button to add or remove a roundabout.
Add missing POI
Tap this button to add a new Point of Interest (POI).
For example to add a new restaurant near to your current location:
1. Tap Add missing POI.
2. Tap Restaurant in the list of POI categories.
3. Tap Near you.
You can select the location by entering the address or by selecting
the location on the map. Select Near you or Near home to open the
map at your current location or at your Home location
4. Select the location of the missing restaurant.
5. Tap Done.
6. Type the name of the restaurant then tap Next.
7. If you know the telephone number of the restaurant you can type it,
then tap Next.
If you don't know the number, just tap Next without typing a number.
1. Tap Continue.
Edit POI
Tap this button to edit an existing POI.
You can use this button to make the following changes to a POI:
Delete the POI.
Rename the POI.
Change the telephone number of the POI.
Change the category that a POI belongs to.
Move the POI on the map.
Comment on POI
Tap this button to enter a comment about a POI. Use this button if you
cannot edit the error with the POI using the Edit POI button.
48
Correct house
number
Tap this button to correct the location of a house number. Enter the
address that you wish to correct and then indicate on the map the correct
location of that house number.
Existing street
Tap this button to edit an existing street. Once you have selected the
street, you can select an error to report. You can select more than one
type of error for a street.
Missing street
Tap this button to report a missing street. You have to select the start
and end points of the missing street.
City
Tap this button to report an error about a city, town or village. You can
report the following types of error:
City is missing
Wrong city name
Alternative city name
Other
Motorway en-
trance/exit
Tap this button to report an error about a motorway entrance or exit.
Postcode
Tap this button to report an error about a postcode.
Other
Tap this button to report other types of corrections.
These corrections are not immediately applied to your map but are saved
in a special report.
You can report missing streets, errors in motorway entrances and exits
and missing roundabouts. If the correction you want to report is not
covered by any of these report types, enter a general description then
tap Other.
49
About sounds and voices
Your TomTom device uses sound for some or all of the following:
Driving directions and other route instructions
Warnings that you set
Hands-free phone calls
Note: Hands-free calling is not supported on all navigation devices.
There are two types of voice available for your device:
Computer voices
Computer voices are generated by your device. They provide route instructions and read
aloud city and street names, traffic and other useful information.
Human voices
These are recorded by an actor and only provide route instructions.
Note: Not all devices have computer voices.
About computer voices
Your TomTom device uses text-to-speech technology and computer voices to read the street
names on your map as it guides you on your route.
The computer voice analyses the whole phrase or sentence before speaking, to ensure that the
sentence sounds as close as possible to natural speech.
Computer voices can recognise and pronounce foreign towns and street names. For example, the
English computer voice can read and pronounce French street names but pronunciation may not
be completely accurate.
Selecting a voice
To select a different voice on your TomTom device, either tap Change voice in the Settings menu
or tap Voices, then tap Change voice and select the required voice.
Changing the volume level
You can change the volume on your TomTom device in several ways.
In the Driving view.
Tap the central panel on the status bar and move the slider to adjust the volume. The last
route instruction is played so you can hear the new volume level.
In the Settings menu.
Tap Settings in the Main menu, then tap Volume and move the slider to adjust the volume.
Tap Test to listen to the new volume level.
Sounds and voices
50
Automatic volume control
To set your TomTom device to automatically adjust the volume, do the following:
1. Tap Settings in the Main menu.
2. Tap Volume.
3. Select Link volume to car speed to automatically adjust the volume inside the car in response
to changes in the speed of your driving.
4. Tap Done.
51
About Settings
You can change the way your TomTom device looks and behaves. Most of the settings on your
device can be accessed by tapping Settings in the Main menu.
Note: Not all settings described here are available on all devices.
2D/3D settings
2D/3D settings
Tap this button to set the default view of the map. To switch between 2D
and 3D views while driving, tap the left side of the status bar in the
Driving View.
It is sometimes easier to view the map from above, such as when navi-
gating a complex road network.
The 2D view shows a two dimensional view of the map as though
viewed from above.
The 3D view shows a three dimensional view of the map as though you
are driving through the landscape.
The following buttons are available:
In 2D view: rotate map in direction of travel - tap this button so the
map is rotated automatically with the direction you are travelling al-
ways at the top.
Switch to 3D view when following a route - tap this button to show
the map automatically in 3D view when you are following a route.
Advanced settings
Advanced settings
Tap this button to select the following advanced settings:
Show house number before street name - when this setting is
selected, addresses are shown with the house number followed by
the street name, such as 10 Downing Street.
Show street names - when this setting is selected, street names are
shown on the map in the Driving View. You do not need to select this
option when your TomTom is set to read aloud street names using a
computer voice.
Show next street name - when this setting is selected, the name of
the next street on your route is shown at the top of the Driving View.
Show current street name on map - when this setting is selected,
the name of the street you are on is shown at the bottom of the Driv-
ing View.
Show location preview - when this setting is selected, a graphical
preview of your destination is shown during route planning.
Enable automatic zooming in 2D view
Settings
52
Enable automatic zooming in 3D view
Show lane images - when this setting is selected, a graphical view of
the road ahead shows which lane you need when you approach a
junction or motorway exit. You can choose to see a split-screen lane
image, a full-screen lane image or you can switch off lane images al-
together. This feature is not available for all roads.
Show tips - this setting switches tips on and off.
Automatically adjust clock for time zone - when this setting is
selected, your clock is automatically adjusted for your time zone.
Battery saving
Battery saving
To change the power saving settings, tap this button on your device.
Brightness
Brightness
Tap this button to set the brightness of the screen. Move the sliders to
adjust the brightness level.
To view the map and menus in day or night colours, tap Use day colours
or Use night colours in the Settings menu.
Car symbol
Car symbol
Tap this button to select the car symbol that shows your current location
in the Driving view.
Clock
Clock
Tap this button to select the time format. As soon as you have a GPS fix,
the time will be set automatically. If you don't have a GPS fix, you can
choose to set the time manually.
Connections
Connections
Tap this button to open the Connections menu. The menu items let you
control your navigation device's connections.
53
Enable / Disable Bluetooth
Enable Bluetooth
Tap this button to enable Bluetooth®.
Note: This feature is not available on all TomTom navigation devices.
Disable Bluetooth
Tap this button to disable Bluetooth®.
Note: This feature is not available on all TomTom navigation devices.
Enable / Disable flight mode
Enable / Disable
flight mode
Tap this button to enable or disable flight mode. Flight mode stops all
communication from the device.
Favourites
Favourites
Tap this button to add, rename or delete Favourites.
Favourites provide an easy way to select a location without the need to
enter the address. They do not need to be favourite places, they can
simply be seen as a collection of useful addresses.
To create a new Favourite, tap Add. Then enter the location address in
the same way that you enter an address when you plan a route.
To view or change an existing Favourite, tap one of the items in the list.
To see more Favourites on the map, tap the left or right buttons.
54
GPS status
GPS status
Tap this button to see the current status of GPS reception on your
device.
Home location
Home location
Tap this button to set or change your Home location. You enter the
address in the same way as you do when you plan a route.
Your Home location provides an easy way to plan a route to an important
location.
For most people, your Home location will be your home address. How-
ever, you might prefer to set the location to another regular destination,
such as your workplace.
Keyboard
Keyboard
Tap this button to select the keyboards that will be available for your use
and the layout of the Latin keyboard.
You use the keyboard to enter names and addresses, such as when you
plan a route or search for the name of a town or a local restaurant.
Language
Language
Tap this button to change the language used for all the buttons and
messages you see on your device.
You can choose from a wide range of languages. When you change the
language, you are also given the opportunity to change the voice.
55
Make your own menu
Make your own
menu
Tap this button to add up to six buttons to your own personalised menu.
If there are only one or two buttons in your menu, both buttons are
shown in the Driving view.
If you have three or more buttons in your menu, then a single button is
shown in the Driving view which opens your menu when tapped.
Manage POIs
Manage POIs
Tap this button to manage your own Point of Interest (POI) categories
and locations.
You can set your TomTom device to let you know when you are near to
selected POI locations. For example, you could set the device to let you
know when you are approaching a petrol station.
You can create your own POI categories and add your own POI locations
to these categories.
You can, for example, create a new POI category called Friends. You
could then add all your friends' addresses as POIs in this new category.
Tap the following buttons to create and maintain your own POIs:
Add POI - tap this button to add a location to one of your own POI
categories.
Warn when near POI - tap this button to set your device to warn you
when you are near selected POIs.
Delete POI - tap this button to delete a POI.
Edit POI - tap this button to edit one of your own POIs.
Add POI category - tap this button to create a new POI category.
Delete POI category - tap this button to delete one of your own POI
categories.
Map colours
Map colours
Tap this button to select the colour schemes for day and night map
colours.
Tap Search to search for a colour scheme by typing the name.
Map corrections
Map corrections
Tap this button to correct errors on your map.
56
Me and my device
Me and my device
Tap this button to find technical information about your TomTom, and to
select whether you want to share information with TomTom.
A menu opens with the following options:
About my device
Tap this button to find technical information about your TomTom, such
as the device serial number, application version and the map version.
My information
Tap this button to change whether you want to share information with
TomTom.
Operate left-handed / Operate right handed
Operate
left-handed /
Operate
right-handed
Tap this button to make it easier for right- or left-handed operation.
This will affect items such as the zoom bar when you are viewing the
map.
Phones
Phones
Tap this button on the Connections menu to open the Phones menu.
Reset factory settings
Reset factory
settings
Tap this button to choose between a full or partial factory reset.
A full reset deletes all your personal settings and restores the standard
factory settings to your TomTom device.
A partial reset deletes your existing personal settings but keeps location
information including Favourites, recent destinations, home and work
locations, POI categories and POIs.
This is not a software update and will not affect the version of the soft-
ware application installed on your device.
Route planning
Route planning
Tap the Route planning button to set the way your TomTom calculates
the routes that you plan.
57
Tap the button for each option to change the settings.
Note: This setting is not available if you are using a TomTom camper
and caravan product.
For camper and caravan products, the vehicle and routes setting is
available instead.
Route types
Set the type of route you want your TomTom to calculate.
Tap IQ Routes to set if you want the device to use IQ Routes information to help find the best
route.
Toll roads, Ferries, Carpool lanes and Unpaved roads settings
Set how your TomTom should manage each of these road features when the device calculates a
route.
Carpool lanes are sometimes known as High Occupancy Vehicle Lanes and are not present in
every country. To travel on these lanes, you may need to have more than one person in the car,
for example, or the car may need to use environmentally-friendly fuel.
Route summary
Set whether you want the route summary screen to close automatically after you plan a route. If
you select No, then you will need to tap Done to close the route summary screen every time you
plan a route.
Safety settings
Safety settings
Tap this button to select the safety features you want to use on your
device.
Show POI on map
Show POI on map
Tap this button to select the types of Point of Interest (POI) you want to
see on the map.
1. Tap Show POI on map in the Settings menu.
2. Select the POI categories you want to be shown on the map.
Tap Search and use the keyboard to search for a category name.
3. Select whether you want POIs to be shown in 2D or 3D views of the
map.
4. Tap Done.
Point of Interest locations are shown on the map as symbols.
58
Speaker
Speaker
Tap this button to select the loudspeaker or loudspeaker connection that
is used by your device.
Start up
Start up
Tap this button to set what happens when your device starts.
Status bar
Status bar
Tap this button to select the information you want to see on the status
bar:
Horizontal - show the status bar at the bottom of the Driving view.
Vertical - show the status bar on the right-hand side of the Driving
view.
Maximum speed
Important: The speed limit is shown next to your current speed. If you
drive faster than the speed limit, you see a warning indicator in the status
bar, for example the status bar pane turns red.
Information about speed limits is not available for all roads.
Current time
Remaining distance - the distance to your destination.
Leeway - your device shows how late or early you will arrive, com-
pared with your preferred arrival time that was set when you planned
the route.
Switch map
Maps
Tap this button to select the map you want to use for route planning and
navigation.
Although you can store more than one map on the device, you can only
use one map at a time for planning and navigation.
To switch from the current map to plan a route in another country or
region, simply tap this button.
Note: The first time you switch to a map, you may need to connect to
your MyTomTom account and activate the map.
59
Turn off voice guidance / Turn on voice guidance
Turn off Voice
guidance
Tap this button to switch off voice guidance. You will no longer hear
spoken route instructions but you will still hear information such as traffic
information and warnings.
Voice guidance is also switched off if you tap Turn off sound in the
Settings menu.
Note: If you change the voice on your device, then voice guidance is
automatically switched on for the new voice.
Turn on Voice
guidance
Tap this button to switch on voice guidance and hear spoken route
instructions.
Units
Units
Tap this button to set the units used on your device for features such as
route planning.
Use night colours / Use day colours
Use night colours
Tap this button to reduce the brightness of the screen and display the
map in darker colours.
When driving at night or when driving through a dark tunnel, it is easier
to view the screen and less distracting for the driver if the brightness of
the screen is dimmed.
Tip: Your device can switch between day and night colours depending
on the time of day. To automatically switch between night and day
colours, tap Brightness in the Settings menu and select Switch to night
colours when dark.
Use day colours
Tap this button to increase the brightness of the screen and display the
map in brighter colours.
Vehicle and routes
Vehicle and routes
Tap this button to set your vehicle type and change how routes are
planned.
Tap the button for each option to change the settings.
Note: This setting is only available if you are using a TomTom camper
and caravan product.
For other products, the route planning setting is available instead.
60
To set up your vehicle, or change between vehicles, tap Vehicle and route types.
You can then select your vehicle type and set up your device for your vehicle.
Route types
Set the type of route you want your TomTom to calculate.
Tap IQ Routes to set if you want the device to use IQ Routes information to help find the best
route.
Toll roads, Ferries, Carpool lanes and Unpaved roads settings
Set how your TomTom should manage each of these road features when the device calculates a
route.
Carpool lanes are sometimes known as High Occupancy Vehicle Lanes and are not present in
every country. To travel on these lanes, you may need to have more than one person in the car,
for example, or the car may need to use environmentally-friendly fuel.
Route summary
Set whether you want the route summary screen to close automatically after you plan a route. If
you select No, then you will need to tap Done to close the route summary screen every time you
plan a route.
Voices
Change voice
Tap this button to change the voice that gives spoken directions and
other route instructions.
A wide range of voices are available. There are computer voices which
can read street names and other information directly from the map and
there are human voices which have been recorded by actors.
Voice settings
Tap this button to set the type of spoken directions and other route
instructions your device will read aloud.
Voice control
Voice control
Tap this button to open the Voice control menu which contains the
following buttons:
Disable voice
control
Tap this button to disable voice control.
61
Enable voice
control
Tap this button to enable voice control.
What to say
Tap this button to see a list of commands you can say when using voice
control.
Volume
Volume
Tap this button to set the volume level for your device. Move the slider to
change the volume.
62
About Points of Interest
Points of Interest or POIs are useful places on the map.
Here are some examples:
Restaurants
Hotels
Museums
Parking garages
Petrol stations
Creating POIs
Tip: For help on managing third party POIs, search for "Third party POIs" at:
tomtom.com/support.
1. Tap the screen to open the Main menu.
2. Tap Settings.
3. Tap Manage POIs.
4. If there are no POI categories or the one you want to use does not exist, tap Add POI category
and create a new category.
Every POI must be assigned to a POI category. This means you need to have created at least
one POI category before you can create your first POI.
You can only add POIs to POI categories you have created.
For more information on creating POI categories, read Managing POIs.
5. Tap Add POI.
6. Select the POI category you want to use for the new POI.
7. Tap a button to enter the POI address in the same way that you plan a route.
8. The POI is created and saved in the selected category.
Home
Tap this button to set your Home location as a POI.
This is useful if you decide to change your Home location, but first want
to create a POI using the current Home address.
Points of Interest
63
Favourite
Tap this button to create a POI from a Favourite.
You might want to create a POI from a Favourite because you can only
create a limited number of Favourites. If you want to create more Favour-
ites you need to delete some Favourites. To avoid losing a Favourite,
save the location as a POI before you delete the Favourite.
Address
Tap this button to enter an address as a new POI.
When you enter an address, you can choose from four options.
City centre
Street and house number
Postcode
Crossing or intersection
Recent destination
Tap this button to select a POI location from a list of places you have
recently used as destinations.
Point of Interest
Tap this button to add a Point of Interest (POI) as a POI.
For example, if you are creating a category of POIs for your favourite
restaurants, use this option instead of entering the addresses of the
restaurants.
My location
Tap this button to add your current location as a POI.
For example, if you stop somewhere interesting, you can tap this button
to create a new POI at the current location.
Point on map
Tap this button to create a POI using the map browser.
Use the cursor to select the location of the POI, then tap Done.
Latitude Longitude
Tap this button to create a POI by entering latitude and longitude values.
Position of last
stop
Tap this button to create a POI from your last recorded position.
Spoken address
Tap this button to create a POI by saying the address.
64
Using POIs to plan a route
When you plan a route, you can use a POI for the destination.
The following example shows how to plan a route to a car park in a city:
1. Tap Navigate to or Drive to in the Main menu.
2. Tap Point of Interest.
3. Tap POI in city.
Tip: The last POI you viewed on your TomTom device is also shown in the menu.
4. Enter the name of the town or city and select it when it is shown in the list.
5. Tap the arrow button to expand the list of POI categories.
Tip: If you already know the name of the POI you want to use, you can tap Search by name
to enter the name and select this location.
6. Scroll down the list and tap Car park.
7. The car park closest to the city centre is shown at the top of the list.
8. The following list explains the distances shown next to each POI. How the distance is meas-
ured varies depending on how you initially searched for the POI:
POI near you - distance from your current location
POI in city - distance from the city centre
POI near Home - distance from your Home location
POI along route - distance from your current location
POI near destination - distance from your destination
9. Tap the name of the car park you want to use and tap Done when the route has been calcu-
lated.
Your device starts to guide you to the car park.
Showing POIs on the map
You can select the types of POI locations you want to see on your maps.
1. Tap Show POI on map in the Settings menu.
2. Select the categories you want to be shown on the map.
3. Tap Done.
4. Select whether you want to see POI locations in 2D and 3D views of the map.
5. Tap Done.
The types of POI you have selected are shown as symbols on the map.
Calling a POI
Note: Hands-free calling is not supported on all navigation devices.
Many of the POIs on your TomTom device include phone numbers. This means that if your device
supports hands-free calling, you can use your device to call the POI as well as planning a route to
the location of the POI.
65
For example, you can search for a cinema, call to book a ticket and plan a route to the cinema, and
all using your TomTom device.
1. Tap the phone button in the Driving View.
If the button is not visible in the Driving View, tap Make your own menu in the Settings menu
and select Call... to display the button in the Driving View.
2. Tap Point of Interest.
3. Select how you want to search for the POI.
For example, if you want to search for a POI on your route, tap POI along route.
4. Tap the type of POI you want to call.
For example, if you want to call a cinema to reserve a ticket, tap Cinema and then select the
name of the cinema you want to call. Then tap Call or Dial to make the phone call.
Your TomTom device uses your mobile phone to call the POI.
Setting warnings for POIs
You can set a warning sound to be played when you approach a selected type of POI, such as a
petrol station.
The following example will show how to set a warning sound to be played when you are 250
metres from a petrol station.
1. Tap Manage POIs and then Warn when near POI in the Settings menu.
2. Scroll down the list and tap Petrol station.
Tip: To remove a warning, tap on the category name and then tap Yes. POI categories which
have been set with a warning have a sound symbol next to the category name.
3. Set the distance as 250 metres and tap OK.
4. Select Sound effect and then tap Next.
5. Select the warning sound for the POI and then tap Next.
6. If you only want to hear the warning when the POI is directly on a planned route, select Warn
only if POI is on route. Then tap Done.
The warning is set for the selected POI category. You will hear a warning sound when you are
250 metres from a petrol station on your route.
Manage POIs
Tap Manage POIs to manage your POI categories and locations.
You can set your TomTom device to let you know when you are near to selected POI locations. In
this way you could, for example, set the device to let you know you when you are approaching a
petrol station.
You can create your own POI categories and add your own POI locations to these categories.
This means you can, for example, create a new POI category called Friends. You could then add
all your friends' addresses as POIs in this new category.
66
Tap the following buttons to create and maintain your own POIs:
Add POI - tap this button to add a location to one of your own POI categories.
Warn when near POI - tap this button to set your device to warn you when you are near
selected POIs.
Delete POI - tap this button to delete one of your own POI categories.
Edit POI - tap this button to edit one of your own POIs.
Add POI category - tap this button to create a new POI category.
Delete POI category - tap this button to delete one of your own POI categories.
67
About getting help
Tap Help in the Main menu to navigate to emergency services centres and other specialist ser-
vices. If your device supports hands-free calling and your phone is connected to your device, you
can contact emergency services directly by phone.
For example, if you are involved in a car accident, you could use the Help menu to find and call
the nearest hospital and tell them your exact location.
Tip: If you do not see the Help button in the Main menu, tap Settings and then Safety settings.
Clear the checkbox for Show only essential menu options while driving.
Using Help to phone a local service
Note: Hands-free calling is not supported on all navigation devices.
To use Help to locate a service centre, contact the centre by phone and navigate from your current
location to the centre, do the following:
1. Tap the screen to show the Main Menu.
2. Tap Help.
3. Tap Phone for help.
4. Select the type of service you require, for example, Nearest hospital.
5. Select a centre from the list, the nearest is shown at the top of the list.
Your device shows your position on the map along with a description of the location. This
helps you explain where you are while making a call.
If your navigation device supports hands-free calling and a phone is connected to your device,
your device automatically dials the phone number. If no phone is connected, the phone num-
ber is displayed for you to call.
6. To navigate your way to the centre by car, tap Navigate there. If you are on foot, tap Walk
there.
Your navigation device starts guiding you to your destination.
Help menu options
Note: In some countries, information may not be available for all services.
Phone for help
Tap this button to find the contact details and location of a service
centre.
Note: Hands-free calling is not supported on all devices.
Help
68
Drive to help
Tap this button to navigate your way by car to a service centre.
Walk to help
Tap this button to navigate your way on foot to a service centre.
Where am I?
Tap this button to see your current location on the map.
If hands-free calling is supported on your device, and your phone is
connected to your device, you can tap Where am I?. Select the type of
service you want to contact and tell them your exact location as shown
on your device.
Safety and other
guides
Tap this button to read a selection of guides, including a First Aid guide.
Product manuals
Tap this button to read a selection of guides relating to your navigation
device.
69
About hands-free calls
Note: Hands-free calling is not supported on all devices.
If you have a mobile phone with Bluetooth®, you can use your TomTom device to make phone
calls and send and receive messages.
Important: Not all phones are supported or compatible with all features. For more information, go
to tomtom.com/phones/compatibility.
Connecting to your phone
First you must establish a connection between your mobile phone and your TomTom device.
Tap Connections in the Settings menu, then tap Phones. Tap Manage phones and select your
phone when it is shown in the list.
You only need to do this once and your TomTom device will remember your phone.
Tips
Make sure that you switch on Bluetooth® on your phone.
Make sure that your phone is set to 'discoverable' or 'visible to all'.
You may have to enter the password '0000' on your phone in order to connect to your
TomTom device.
To avoid having to enter '0000' every time you use the phone, save your TomTom device as a
trusted device on your phone.
For additional information about Bluetooth settings, refer to your mobile phone user guide.
Making a call
When you have established a connection between your TomTom device and your mobile phone,
you can use your navigation device to make hands-free calls on your mobile phone.
To make a phone call, tap the phone button in the Driving View. Then tap one of the following
buttons:
Tap Home to call your Home location.
If you have not entered a number for your Home location this button is unavailable.
Tap Phone number to enter a phone number to call.
Tap Point of Interest to choose a Point of Interest (POI) to call.
If your device knows the phone number of a POI, this is shown next to the POI.
Tap Phonebook entry to select a contact from your phonebook.
Note: Your phonebook is automatically copied to your TomTom device when you first establish
a connection with your mobile phone.
Hands-free calling
70
Not all phones can transfer the phonebook to your device. For more information, go to
tomtom.com/phones/compatibility.
Tap Recently dialed to select from a list of people or numbers you have called recently using
your device.
Tap Recent caller to select from a list of people or numbers who called you recently.
Only calls you have received on your device are saved in this list.
Receiving a call
When someone calls you, the caller's name and phone number are shown. Tap the screen to
accept or reject the call.
Auto-answer
You can set your TomTom device to automatically answer incoming phone calls.
To set automatic answering, tap Connections in the Settings menu, then tap Phones. Tap Au-
to-answer settings.
Select how long your device will wait before automatically answering your calls, then tap Done.
Connecting more phones to your device
You can establish connections for up to 5 mobile phones.
To add more phones, do the following.
1. Tap Connections in the Settings menu.
2. Tap Phones.
3. Tap Manage phones.
4. Tap Add and follow the instructions.
To switch between phones, tap Manage phones. Then tap the button for the phone you want to
connect to.
Mobile phone menu
Note: Hands-free calling is not supported on all navigation devices.
Manage phones
Tap this button to manage the mobile phones that will be connected to
your TomTom device.
You can add a profile for up to five different mobile phones.
Disable hands-free
Tap this button to disable or enable hands-free calling.
71
Call
Tap this button to make a phone call.
Change home
number
Tap this button to change your home phone number.
Delete
Tap this button to select information you want to delete. You can delete
the list of recent callers and the list of recently dialled numbers.
Auto-answer
settings
Tap this button to change the auto-answer settings.
Important: Not all phones are supported or compatible with all features.
72
About Favourites
Favourites provide an easy way to select a location without the need to enter the address. They do
not need to be favourite places, they can simply be seen as a collection of useful addresses.
Tip: If you have set-up any frequent destinations, they are shown in your list of Favourites.
Creating a Favourite
To create a Favourite, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Settings to open the Settings menu.
3. Tap Favourites.
4. Tap Add.
Select the type of the Favourite by tapping one of the buttons described below:
Home
You can set your Home location as a Favourite.
Favourite
You cannot create a Favourite from another Favourite. This option
will always be unavailable in this menu.
To rename a Favourite, tap Favourites in the Settings menu.
Address
You can enter an address as a Favourite.
Recent destination
Create a new Favourite by selecting a location from a list of your
recent destinations.
Point of Interest
If you visit a POI you particularly like, for example a restaurant, you
can add it as a Favourite.
Favourites
73
My location
Tap this button to add your current location as a Favourite.
For example, if you stop somewhere interesting, while you are there
you can tap this button to create the Favourite.
Point on map
Tap this button to create a Favourite using the Map Browser.
Select the location of the Favourite using the cursor, then tap Done.
Latitude Longitude
Tap this button to create a Favourite by entering latitude and longi-
tude values.
Spoken address
Tap this button to create a Favourite by saying the address.
Position of last
stop
Tap this button to select your last recorded position as your destina-
tion.
Your device suggests a name for your new Favourite. To enter a new name, there is no need
to delete the suggested name, you just start typing.
Tip: It is a good idea to give your Favourite a name that is easy to remember.
Tap OK.
Your new favourite appears in the list.
After you have added two or more Favourites, and Tips are switched on, you are asked whether
you make regular trips to the same locations. If you tap YES, you can enter these destinations as
your favourite destinations. Every time you switch on your device, you can immediately select one
of these locations as your destination. To change these destinations or select a new destination,
tap Start-up in the Settings menu, then select Ask for a destination.
Using a Favourite
You can use a Favourite as a way of navigating to a place without having to enter the address. To
navigate to a Favourite, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Navigate to or Drive to.
3. Tap Favourite.
4. Select a Favourite from the list.
Your TomTom device calculates the route for you.
5. When the route is calculated, tap Done.
74
Your device immediately starts guiding you to your destination with spoken instructions and visual
instructions on the screen.
Changing the name of a Favourite
To change the name of a Favourite, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Settings to open the Settings menu.
3. Tap Favourites.
4. Tap the Favourite you want to rename.
Tip: Use the left and right arrows to choose another Favourite from your list.
5. Tap Rename.
6. Type in the new name and then tap Done.
7. Tap Done.
Deleting a Favourite
To delete a Favourite, do the following:
1. Tap the screen to bring up the Main menu.
2. Tap Settings to open the Settings menu.
3. Tap Favourites.
4. Tap the Favourite you want to delete.
Tip: Use the left and right arrows to choose another Favourite from your list.
5. Tap Delete.
6. Tap Yes to confirm the deletion.
7. Tap Done.
75
About RDS-TMC
The Traffic Message Channel (TMC), also known as RDS-TMC, transmits traffic information as a
radio signal and is available free of charge in many countries.
TMC is not a TomTom Service, but is available when using the TomTom RDS-TMC Traffic Receiv-
er.
Note: TomTom is not responsible for the availability or quality of traffic information provided by
the Traffic Message Channel.
The Traffic Message Channel (TMC) is not available in all countries. To check the availability of
TMC services in your country, go to tomtom.com/5826.
Using traffic information
If you are using an RDS-TMC receiver to view TMC traffic information on your TomTom device,
connect the TomTom RDS-TMC Traffic Receiver to the USB connector on your device.
The traffic sidebar is shown on the right side of the Driving View. The sidebar informs you about
traffic delays while you drive, using glowing dots to show you where each traffic incident is
located on your route.
The top of the traffic sidebar represents your destination and shows the
total time delay due to traffic jams and other incidents on your route.
The central section of the traffic sidebar shows individual traffic incidents
in the order they occur on your route.
The bottom of the traffic sidebar represents your current location and
shows the distance to the next incident on your route.
To make the traffic sidebar more readable some incidents may not be shown. These incidents will
always be of minor importance and only cause short delays.
The colour of the pointers, as shown below, gives you an instant indication of the type of incident:
Unknown or undetermined situation.
Slow traffic.
Queueing traffic.
Traffic
76
Stationary traffic or road closure.
Taking the fastest route
Your TomTom device regularly looks for a faster route to your destination. If the traffic situation
changes and a faster route is found, your device offers to replan your journey so you can use the
faster route.
You can also set your device to automatically replan your journey whenever a faster route is
found. To apply this setting, tap Traffic settings in the Traffic menu.
To manually find and replan the fastest route to your destination, do the following:
1. Tap the traffic sidebar.
Tip: If you find that tapping the sidebar opens the Main menu instead of the traffic menu, try
tapping the sidebar with your finger resting on the edge of the screen.
A summary of traffic on your route is shown.
2. Tap Options.
3. Tap Minimise delays.
Your device searches for the fastest route to your destination.
The new route may include traffic delays. You can replan the route to avoid all traffic delays,
but a route which avoids all delays will usually take longer than the fastest route.
4. Tap Done.
Minimising delays
You can use TomTom Traffic to minimise the impact of traffic delays on your route. To minimise
delays automatically, do the following:
1. Tap Services in the Main Menu.
2. Tap Traffic.
3. Tap Traffic settings.
4. Choose between always taking the faster route automatically, being asked or never changing
your route.
5. Tap Next and then Done.
6. Tap Minimise delays.
Your device plans the quickest route to your destination. The new route may include traffic
delays and may remain the same as the original route.
You can re-plan the route to avoid all delays, but this route is unlikely to be the quickest possi-
ble route.
7. Tap Done.
Making commuting to work easier
The Home to work or Work to home buttons in the Show home-work traffic menu lets you check
your route to and from work with one tap of a button.
When you use either of these buttons, your device plans a route between your home and work
locations and checks the route for possible delays.
77
The first time you use Home to work, you must set your traffic home and work locations by doing
the following:
1. Tap the traffic sidebar to open the Traffic menu.
Note: If you already have a route planned, a summary of traffic incidents on your route is
shown. Tap Options to open the Traffic menu.
2. Tap Show home-work traffic.
3. Set your home location and your work location.
If you have already set the locations and want to change them, tap Change home-work.
You can now use the Home to work and Work to home buttons.
Note: The home location you set here is not the same as the home location you can set in the
Settings Menu. In addition, the locations you use here do not have to be your actual home and
work locations. If there is another route that you often travel, you can set Work/Home to use
these locations instead.
For example, to check for delays on your route home before you leave the office, do the following:
1. Tap the traffic sidebar to open the Traffic menu.
Note: If you already have a route planned, a summary of traffic incidents on your route is
shown. Tap Options to open the Traffic menu.
2. Tap Show home-work traffic.
3. Tap Work to home.
The Driving View is shown and a message is displayed telling you about traffic incidents on this
route. The Traffic sidebar also shows any delays.
Getting more information about an incident
To check for delays on your route, tap Show traffic on route in the Traffic menu. Your navigation
device shows a summary of the traffic delays on your route.
The total includes any delays due to traffic incidents and those due to busy roads, with infor-
mation provided by IQ Routes.
78
Tap Minimise delays to check if you can reduce the delay.
Tap the left and right arrow buttons to move through each incident in turn, viewing the details of
each one. This includes the type of incident, for example road works, and the length of delay
caused by this incident.
You can also access the details about individual incidents by tapping View map in the Main Menu
and then tapping on the traffic incident symbol.
When shown on the map, a traffic incident starts with an icon. In the case of a traffic queue, the
direction of the incident is from the icon towards the other end.
Checking traffic incidents in your area
Get an overview of the traffic situation in your area, using the map. To find local incidents and
their details, do the following:
1. Tap the traffic sidebar then tap Options to open the Traffic menu.
2. Tap View map.
The map overview screen is shown.
3. If the map does not show your location, tap the marker to centre the map on your current
location.
79
The map shows traffic incidents in the area.
4. Tap on any traffic incident to get more information.
A screen is shown that gives you detailed information about the incident you chose. To dis-
play information about surrounding incidents use the left and right arrows at the bottom of this
screen.
Changing traffic settings
Use the Traffic settings button to choose how traffic information works on your navigation device.
1. Tap the traffic sidebar then tap Options to open the Traffic menu.
2. Tap Traffic settings.
3. If you are using an RDS-TMC Traffic Receiver, you will be able to select the setting Tune
manually by entering a frequency. If you select this option, the button Tune manually is
shown in the Traffic menu. Tap Tune manually to enter the frequency of a particular radio sta-
tion you want to use for RDS-TMC traffic information
4. If a faster route is found while you are driving, Traffic can replan your journey to use the faster
route. Select one of the following options and then tap Done.
Always switch to that route
Ask me if I want that route
Never change my route
Traffic incidents
Traffic incidents and warnings are shown on the map, in the Driving View and on the Traffic
sidebar.
To find out more about an incident, tap View Map in the Main Menu. Tap on a traffic incident
symbol on the map to see information about that incident. To display information about sur-
rounding incidents, use the left and right arrows at the bottom of the screen.
There are two types of incident and warning signs:
Symbols shown in a red square are traffic incidents. Your navigation device can replan to
avoid them.
80
Symbols shown in a red triangle are weather related. Your device does not replan to avoid
these warnings.
Traffic incident symbols:
Accident
Road works
One or more lanes closed
Road closed
Traffic incident
Traffic jam
Weather related symbols:
Fog
Rain
Wind
Ice
Snow
Note: The incident avoided symbol is shown for any traffic incident
that you avoid using a traffic service.
Traffic menu
To open the Traffic menu, tap the Traffic sidebar in the Driving View then tap Options, or tap
Traffic in the Services menu.
The following buttons are available:
81
Minimise traffic
delays
Tap this button to re-plan your route based on the latest traffic infor-
mation.
Show home-work
traffic
Tap this button to calculate the quickest route from your home location
to your place of work and back.
Show traffic on
route
Tap this button for an overview of traffic incidents along your route.
Tap the left and right buttons for more detailed information about each
incident.
Tap Minimise delays to replan your route and avoid the traffic incidents
that are shown on the map.
View map
Tap this button to browse the map and see the traffic incidents shown on
the map.
Change Traffic
settings
Tap this button to change your settings for how the Traffic service works
on your device.
Read aloud traffic
info
Tap this button to hear spoken information about traffic incidents on your
route.
Note: Your TomTom device must have a computer voice installed to
read information aloud.
82
About Speed Cameras
The Speed Cameras service warns you about a range of speed cameras and safety alerts including
the following:
Fixed speed camera locations.
Accident blackspot locations.
Mobile speed camera locations.
Average speed check camera locations.
Traffic light camera locations.
Ungated railway crossings.
Speed camera warnings
By default, a warning sound is played for the most common types of speed camera. To change
the warning sound, tap Alert settings in the Speed Cameras menu.
You are warned about speed cameras in three ways:
Your device plays a warning sound.
The type of speed camera and your distance from the camera is shown in the Driving View.
The speed limit is also shown in the Driving View.
The location of the speed camera is shown on the map.
Note: For average speed check cameras, your device warns you at the start and end of the
average speed check area.
Changing the way you are warned
To change the way your TomTom device warns you about speed cameras, tap the Alert settings
button.
You can then set what type of sound is played.
For example, to change the sound that is played when you approach a fixed speed camera, do the
following:
1. Tap Services in the Main Menu.
2. Tap Speed Cameras.
3. Tap Alert settings.
A list of speed camera types is displayed. A speaker is shown next to the speed camera types
that have an alert set.
Speed Cameras
83
4. Tap Fixed cameras.
5. Select whether you always want to be warned or warned only when you are speeding. Select
Never to turn off the warning.
6. Tap the sound you want to be used for the warning.
7. Tap Next.
The warning sound you selected is now set for fixed speed cameras. A speaker symbol is shown
next to Fixed cameras in the list of types of speed camera.
Speed camera symbols
Speed cameras are shown as symbols in the Driving View.
As you approach a camera, you see a symbol showing the type of camera and the distance to the
camera. A warning sound is played. You can change the warning sound for cameras or turn
warning sounds on and off for each camera.
Tap the camera symbol to report that the camera is no longer there or to confirm that it is still
there.
When you first start using your device, warning sounds are played for these types of cameras:
Fixed speed camera - this type of camera checks the speed of passing
vehicles and is fixed in one place.
Traffic light camera - this type of camera checks for vehicles breaking
traffic rules at traffic lights. Some traffic light cameras may also check
your speed.
Average speed check - these types of cameras measure your average
speed between two points. You are warned at the start and end of the
average speed check area.
While you are driving in an average speed check area, your average
speed is shown, instead of your current speed.
When you are in the speed check area, the visual warning continues to
be shown in the Driving View.
Accident blackspot
84
Ungated railway crossing
Toll road camera
When you first start using your device, no warning sounds are played for these types of cameras:
Restricted road camera
Other camera
Bidirectional camera
Updating locations for cameras and alerts
The locations of speed cameras can change frequently. New cameras can also appear without
warning and the locations for other alerts, such as accident blackspots, may also change position.
Hence, it is important to ensure that your device has the latest camera and alert locations.
To get the latest locations for fixed cameras and mobile camera hotspots (likely mobile camera
locations), connect your device to your computer and use MyDrive. Connecting once a week to
MyDrive is enough to make sure that you have the latest camera and alert locations on your
device.
Report button
To show the report button in the Driving View, do the following:
1. Tap Services in the Main Menu.
2. Tap Speed Cameras.
3. Tap Show report button.
85
4. Tap Back.
The report button is shown on left-hand side of the Driving View or if you are already using the
quick menu, it's added to the buttons available in the quick menu.
Tip: To hide the report button, tap Hide report button in the Speed Cameras menu.
Reporting a new speed camera while on the move
To report a speed camera on the move, do the following:
1. Tap the report button shown in the Driving View or in the quick menu to record the location of
the camera.
2. Confirm that you want to add a camera.
You see a message thanking you for adding the camera.
Reporting a new speed camera while at home
You do not need to be at the location of a speed camera to report the new location. To report a
new speed camera location while you are at home, do the following:
1. Tap Services in the Main Menu on your navigation device.
2. Tap Speed Cameras.
3. Tap Report speed camera.
4. Select the type of camera.
5. Use the cursor to mark the location of the camera on the map, then tap Next.
6. Tap Yes to confirm the location of the camera, or tap No to mark the location again on the
map.
You see a message thanking you for reporting the camera.
Reporting incorrect camera alerts
You may receive an alert for a camera that is no longer there. To report an incorrect camera alert,
do the following:
Note: You can only report an incorrect camera alert while you are at the location.
1. While you are being warned about the camera, tap the warning.
2. Confirm whether the camera is still there or not.
Types of speed camera you can report
When you report a speed camera while at home, you can select the type of camera you are
reporting.
These are the different types of speed camera you can report from home:
86
Fixed speed camera - this type of camera checks the speed of passing vehicles and is fixed in
one place.
Mobile speed camera - this type of camera checks the speed of passing vehicles and is moved
to different places.
Red light camera - this type of camera checks for vehicles breaking traffic rules at traffic lights.
Toll road camera - this type of camera monitors traffic at toll road barriers.
Other camera - all other types of camera that do not fall into any of the above categories.
Average speed check camera warnings
You can set whether you want to be warned about the cameras at the start and end of an average
speed check area. To change the settings, tap Alert settings in the Speed Cameras menu.
While you are driving in an average speed check area, your average speed is shown, instead of
your current speed.
As you approach the start of an average speed check zone, you see a visual warning in the Driving
View with a distance to the camera underneath it. You hear an audible warning.
You also see a small icon on the road showing the position of the average speed check camera at
the start of the zone.
During the zone, the visual warning continues to be shown in the Driving View.
Speed Cameras menu
To open the Speed Cameras menu, tap Services in the Main Menu and then tap Speed Cameras.
Report speed
camera
Tap this button to report a new speed camera location.
Alert settings
Tap this button to set the alerts you will receive and the sounds used for
each alert.
Disable alerts
Tap this button to disable all alerts at once.
88
About danger zones
Since 3rd January 2012, it has been illegal to receive warnings about the position of fixed or
mobile speed cameras when you are driving in France. To be compliant with this change in French
law, all types of speed camera locations are no longer reported but instead, areas of danger are
indicated as zones.
In France, TomTom terminated the Speed Cameras service and introduced a new service called
TomTom Danger Zones.
Danger zones may or may not contain one or more speed cameras or a range of other driving
hazards:
Specific locations are not available and a danger zone icon is shown instead as you approach
the zone.
The minimum length of the zone depends on the road type and is 300m for roads in built-up
areas, 2000m (2km) for secondary roads or 4000m (4km) for motorways.
The location of one or more speed cameras, if any, can be at any point within the zone.
If two danger zones are close to each other, the warnings can be merged into a single longer
zone.
Important: Outside France, you receive warnings about speed cameras. Inside France, you
receive warnings about danger zones. When you cross the border, the type of warning you
receive changes.
Danger zone warnings
Warnings are given 10 seconds before you reach a danger zone. You are warned in the following
ways:
Your device plays a warning sound.
You see a marker on the road in the Driving View showing the start of the zone.
You see a warning panel.
Danger zones have minimum lengths: Highways 4km, Secondary roads 2km and built-up
areas 300m.
Changing the way you are warned
These settings allow you to control danger zone warnings and also to change alert sounds.
1. Tap Settings in the Main menu.
2. Tap Services.
3. Tap Safety Alerts.
4. Tap Disable/Enable Alerts to turn Safety Alerts off or on.
5. Tap Disable/Enable report button to hide or show the report button in the Driving View.
Danger Zones
89
6. Tap Alert settings and select if you want to have a warning when approaching a danger zone,
then choose a warning sound.
Danger zone symbols
Danger zones are shown using a symbol in the Driving View.
As you approach a danger zone, you see a symbol. A warning sound is played. You can change
the warning sound for danger zones or turn warning sounds off completely.
When you first start using your device, a warning sound is played for this type of zone:
Danger zone - this type of warning is only given in France where you are
only warned about danger zones. Danger zones include all other types of
warnings.
Report button
Tap this button in the Driving View to report a danger zone. A confirma-
tion screen appears. Tap Yes to confirm the danger zone. A Thank you
icon is shown on the screen. The location is reported to TomTom and
shared with other users.
Note: It is not possible to remove a danger zone.
Reporting a new danger zone while on the move
To report a danger zone while on the move, do the following:
1. Tap the report button shown in the Driving View or in the quick menu to record the location of
the danger zone.
2. Confirm that you want to add a danger zone.
You see a message confirming that a report has been created.
Reporting a new danger zone while at home
You do not need to be at the location of a danger zone to report the new location. To report a new
danger zone location while you are at home, do the following:
1. Tap Services in the Main Menu on your navigation device.
2. Tap Safety Alerts.
3. Tap Report danger zone.
4. Use the cursor to mark the location of the danger zone on the map, then tap Done.
5. Tap Yes to confirm the location of the danger zone.
You see a message confirming that a report has been created.
Safety Alerts menu
To open the Safety Alerts menu, tap Settings in the Main Menu, followed by Services. Then tap
Safety Alerts.
90
Report danger
zone
Tap this button to report a new danger zone location.
Alert settings
Tap this button to set when you receive alerts and the sound.
Disable alerts
Tap this button to disable alerts.
Enable report
button
Tap this button to enable the report button. The report button is shown in
the Driving View or in the quick menu.
When the report button is shown in the Driving View, this button chang-
es to Disable report button.
91
About TomTom camper and caravan products
TomTom camper and caravan products let you choose the type of vehicle you are driving so that
the route planned by your device is suitable for your vehicle. You can choose a car, a car with
caravan, a motorhome, or a van as the vehicle type. Routes planned by your device avoid re-
strictions for the vehicle type. For example, a route calculated for a motorhome may be different
from the route calculated for a car. You can set the size, weight and type of your vehicle as well as
your preferred type of route.
Before you can choose your vehicle type you must select the camper and caravan map on your
device.
Important: You must pay attention to all traffic signs, especially those relating to your vehicle’s
dimensions and weight. We cannot guarantee you will never encounter them on your route and
ignoring such restrictions can be dangerous.
You can select your vehicle in the quick menu in the Driving View. If there are only one or two
buttons in your quick menu, a small icon in the Driving View shows the type of vehicle selected. If
a route is already planned and you select a different vehicle, the route is recalculated for the new
vehicle.
If a route for a caravan, a camper or a van is not found, you are asked if you want to use a car
route instead. If you use a car route, pay attention to restrictions you may find on the route.
You can enter the details about the vehicle you are driving and your route type in the Settings
menu.
Vehicle types
You can select a vehicle from the following vehicle types:
Car
Select Car when you are driving a car without towing a caravan or trailer.
Car with caravan
Select Car with caravan when you are towing a caravan, a trailer tent, a
horse trailer or just a trailer.
Tip: Select Car when you have unhitched your caravan or trailer from
your car.
Camper
Select Camper when you are driving a camper or motorhome.
TomTom camper and caravan products
92
Van
Select Van when you are driving a private van, a rental van, or other
large, non-commercial vehicle.
Set up your vehicle
Before you can plan a route using roads suitable for your vehicle type you must first enter the
details for your vehicle or vehicle combination.
1. Tap Settings in the Main Menu.
2. Tap Vehicle and routes, and then tap Vehicles and route types.
3. Tap your vehicle type. You can enter details for a Car with caravan, a Camper, and a Van.
Note: The Car button opens the standard route planning options.
4. On the Current vehicle profile screen, tap Change.
5. Enter the vehicle's weights, dimensions and speed limit. Press Next each time to move to the
next screen.
Note: The speed limit can be different in each state or country, and different for each type of
vehicle. You must enter the speed limit for the country you are travelling in.
Important: The dimensions and weight for your caravan also include your car's dimensions
and weight.
6. In Avoid motorways, choose whether you want to avoid motorways. Tap Next.
7. In Restriction and dead-end warnings, choose if you want to receive warnings about re-
strictions and dead-ends. Tap Next.
Important: Set this option to Yes if you are driving a large camper or when towing a caravan.
This option prevents you from driving into a difficult situation, such as a place where it is dif-
ficult to turn, or which has a height restriction. You only receive restriction and dead-end
warnings when you are driving with no route planned.
8. Set the Replanning settings.
Note: This setting is only available if your device has either a traffic subscription or an
RDS-TMC Receiver. Traffic information is not available in all countries or regions. For more
information about TomTom traffic information services, go to tomtom.com/services.
Set whether you want your navigation device to replan the current route if a faster route is
found while you are driving. This is useful if traffic builds up or clears further ahead on your
route. Choose from the following settings:
Always switch to that route - select this option to receive no messages when a faster
route is found. The current route is automatically re-calculated to be the fastest one.
Ask me if I want that route - select this option to be asked if you want to take the new
route. When asked if you wish to take the alternative route, tap Yes to have the current
route re-calculated as the fastest one. Tap No if you don't want to take the alternative
route. If you change your mind, tap the balloon at the top of the screen to take the alterna-
tive route.
Never change my route - select this option to always continue on your planned route.
Tap Next.
93
9. In Map information settings, set whether you want to be warned if your route passes through
an area where your map contains only limited information. Tap Done.
Selecting a camper and caravan map
You must first select a camper and caravan map before you can use your TomTom camper and
caravan product.
1. Tap Settings in the Main menu.
2. Tap Switch map.
3. Tap the camper map to select it.
4. Click Done in the Settings menu to return to the Driving View.
Selecting your vehicle type
You can quickly change your vehicle type in the quick menu in the Driving view as follows:
Note: You must first add the vehicle type option to the quick menu.
1. Tap the vehicle button in the Driving view. The vehicle button shows the vehicle type currently
chosen:
Tip: If there are three or more items in your quick menu, tap the quick menu button:
Then tap the Change vehicle button.
2. Tap the type of vehicle you drive.
If there are only one or two items in your quick menu, a small icon in the Driving View shows
the type of vehicle that is selected.
If a route is already planned and you select a different vehicle, the route is recalculated for the
new vehicle.
94
Show the vehicle type quick menu button
You can add the vehicles selection button to the quick menu so you can quickly select your
vehicle type.
1. Tap Settings in the Main menu.
2. Tap Make your own menu.
3. Tap Cancel to clear the information screen, or Next then Done to read the information
screens.
4. Select Change between different vehicles.
5. Click Done, then click Done again to return to the Driving View.
95
About MyDrive
MyDrive is a web-based tool that helps you manage the contents and services of your TomTom
navigation device. You use MyDrive to get map updates as well as lots of other things.
You log in to MyDrive on the TomTom website. It is a good idea to frequently connect your
navigation device to MyDrive to ensure you always have the latest updates.
Tip: We recommend using a broadband internet connection whenever you connect your navi-
gation device to MyDrive.
About MyDrive Connect
In order to use MyDrive, you need to install MyDrive Connect on your computer.
MyDrive Connect is an application that allows your navigation device to communicate with the
MyDrive website. MyDrive Connect needs to be running all the time that your device is connected
to your computer.
MyTomTom account
To download content and to use TomTom services, you need a MyTomTom account.
You can create an account using your computer in one of the following ways:
By selecting the Create account button at tomtom.com.
By selecting the green MyTomTom button at tomtom.com.
By going to tomtom.com/getstarted.
Important: Take care when choosing a country during account creation. The correct country is
needed if you make a purchase from the TomTom shop and it cannot be changed after the ac-
count has been created.
Note: If you have more than one TomTom navigation device, you need a separate account for
each device.
Setting up MyDrive
To get ready to use MyDrive for the first time, do the following:
1. On your computer, open a web browser and go to tomtom.com/getstarted.
2. Click Get Started.
3. Click Download MyDrive Connect.
Follow the instructions on the screen.
4. When prompted, connect your device to your computer using the USB cable supplied with
your device, then switch your device on.
MyDrive
96
Note: Use ONLY the USB cable supplied with your device. Other USB cables may not work.
Note: You should plug the USB cable directly into a USB port on your computer and not into
a USB hub or USB port on a keyboard or monitor.
5. Enter the requested information for account creation, including your country.
When set-up is complete, a MyTomTom account is created and your navigation device is
linked to that account.
You can now access MyDrive Connect from the notification area on your desktop.
MyDrive starts automatically after the account is created.
Note: Next time you want to access MyDrive, go to tomtom.com/mydrive in a web browser.
Tip: When you connect your navigation device to your computer, MyDrive Connect tells you
if there are any updates for your device.
97
Important Safety Notices and Warnings
Global Positioning System (GPS) and Global Navigation Satellite System (GLONASS)
The Global Positioning System (GPS) and Global Navigation Satellite System (GLONASS) systems
are satellite-based systems that provide location and timing information around the globe. GPS is
operated and controlled under the sole responsibility of the Government of the United States of
America, who are responsible for its availability and accuracy. GLONASS is operated and con-
trolled under the sole responsibility of the Government of Russia, who are responsible for its
availability and accuracy. Any changes in GPS or GLONASS availability and accuracy, or in envi-
ronmental conditions, may impact the operation of this device. TomTom does not accept any
liability for the availability and accuracy of GPS or GLONASS.
Use with care
Use of TomTom products while driving still means that you need to drive with due care and
attention.
Aircraft and hospitals
Use of devices with an antenna is prohibited on most aircraft, in many hospitals and in many other
locations. This device must not be used in these environments.
Safety messages
Please read and take note of the following important safety advice:
Check your tyre pressures regularly.
Service your vehicle regularly.
Medication can affect your riding or driving ability.
Always use seat belts if available.
Don’t drink and drive.
Most accidents happen less than 5 km from home.
Obey the rules of the road.
Always use your turn indicators.
Every 2 hours, take a break for at least 10 minutes.
Keep your seat belts on.
Keep a safe distance from the vehicle in front.
Before setting off on a motorbike, fasten your helmet correctly.
When riding a motorbike, always wear protective clothing and equipment.
When riding a motorbike, be extra vigilant and always ride defensively.
Battery
This product uses a Lithium-Ion battery.
Addendum
98
Do not use it in a humid, wet and/or corrosive environment. Do not put, store or leave your
product in or near a heat source, in a high temperature location, in strong direct sunlight, in a
microwave oven or in a pressurised container, and do not expose it to temperatures over 60°C
(140°F). Failure to follow these guidelines may cause the battery to leak acid, become hot, explode
or ignite and cause injury and/or damage. Do not pierce, open or disassemble the battery. If the
battery leaks and you come into contact with the leaked fluids, rinse thoroughly with water and
seek medical attention immediately. For safety reasons, and to prolong the lifetime of the battery,
remove your product from your vehicle when you are not driving and keep in a cool, dry place.
Charging will not occur at low (below 0°C/32°F) or high (over 45°C/113°F) temperatures.
Temperatures: Standard operation: 0°C (32°F) to 45°C (113°F); short period storage: -20°C (-4°F) to
60°C (140°F); long period storage: -20°C (-4°F) to 25°C (77°F).
Caution: risk of explosion if battery is replaced by an incorrect type.
Do not remove or attempt to remove the non-user-replaceable battery. If you have a problem with
the battery, please contact TomTom customer support.
THE BATTERY CONTAINED IN THE PRODUCT MUST BE RECYCLED OR DISPOSED OF PROPERLY
ACCORDING TO THE LOCAL LAWS AND REGULATIONS AND ALWAYS KEPT SEPARATE FROM
HOUSEHOLD WASTE. BY DOING THIS YOU WILL HELP CONSERVE THE ENVIRONMENT. USE
YOUR TOMTOM DEVICE ONLY WITH THE SUPPLIED DC POWER LEAD (CAR CHARGER/BATTERY
CABLE), AC ADAPTER (HOME CHARGER), IN AN APPROVED CRADLE OR USING THE SUPPLIED
USB CABLE TO CONNECT TO A COMPUTER FOR BATTERY CHARGING.
If your device requires a charger, please use this device with the charger provided. For replace-
ment chargers, go to tomtom.com for information about approved chargers for your device.
The stated battery life is a maximum possible battery life. The maximum battery life will only be
achieved under specific atmospheric conditions. The estimated maximum battery life is based on
an average usage profile.
For tips on extending the battery life, see this FAQ: tomtom.com/batterytips.
CE marking
This equipment complies with the requirements for CE marking when used in a residential, com-
mercial, vehicular or light industrial environment, achieving all the appropriate provisions of the
relevant legislation in the EU.
R&TTE directive
Hereby, TomTom declares that TomTom products and accessories are in compliance with the
essential requirements and other relevant provisions of the EU Directive 1999/5/EC. The declara-
tion of conformity can be found here: tomtom.com/legal.
99
WEEE directive
The wheelie bin symbol on the product or its packaging indicates that this product shall not be
treated as household waste. In line with EU Directive 2002/96/EC for waste electrical and electronic
equipment (WEEE), this electrical product must not be disposed of as unsorted municipal waste.
Please dispose of this product by returning it to the point of sale or to your local municipal collec-
tion point for recycling. By doing this you will help conserve the environment.
Pacemakers
Pacemaker manufacturers recommend that a minimum of 15cm (6 inches) be maintained between
a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker.
These recommendations are consistent with independent research and recommendations by
Wireless Technology Research.
Guidelines for people with pacemakers
You should ALWAYS keep the device more than 15cm (6 inches) from your pacemaker.
You should not carry the device in a breast pocket.
Other medical devices
Please consult your physician or the manufacturer of the medical device, to determine if the
operation of your wireless product may interfere with the medical device.
This document
Great care was taken in preparing this document. Constant product development may mean that
some information is not entirely up to date. The information in this document is subject to change
without notice.
TomTom shall not be liable for technical or editorial errors or omissions contained herein, nor for
incidental or consequential damages resulting from the performance or use of this document. This
document contains information protected by copyright. No part of this document may be photo-
copied or reproduced in any form without prior written consent from TomTom N.V.
Model names
4EN62, 4CS01, 4CS03, 4CQ02, 4CQ07, 4CQ01, 4KH00, 4KI00, 4KJ00, 4CR52, 4CR51, 4CR42,
4CR41, 4EN42, 4EN52, 4EV42, 4EV52, 4ER50, 4CT50
100
© 2013 TomTom. All rights reserved. TomTom and the "two hands" logo are registered trade-
marks of TomTom N.V. or one of its subsidiaries. Please see tomtom.com/legal for limited war-
ranty and end user licence agreements applying to this product.
© 2013 TomTom. All rights reserved. This material is proprietary and the subject of copyright
protection and/or database rights protection and/or other intellectual property rights owned by
TomTom or its suppliers. The use of this material is subject to the terms of a licence agreement.
Any unauthorised copying or disclosure of this material will lead to criminal and civil liabilities.
Ordnance Survey © Crown Copyright Licence number 100026920.
Data Source © 2013 TomTom
All rights reserved.
SoundClear™ acoustic echo cancellation software © Acoustic Technologies Inc.
Nuance® is a registered trademark of Nuance Communications, Inc. and is used here under
licence.
Some images are taken from NASA’s Earth Observatory.
The purpose of NASA's Earth Observatory is to provide a freely-accessible publication on the
Internet where the public can obtain new satellite imagery and scientific information about our
home planet.
The focus is on Earth’s climate and environmental change: earthobservatory.nasa.gov
The software included in this product contains copyrighted software that is licensed under the
GPL. A copy of that licence can be viewed in the Licence section. You can obtain the complete
corresponding source code from us for a period of three years after our last shipment of this
product. For more information, visit tomtom.com/gpl or contact your local TomTom customer
support team via tomtom.com/support. Upon request, we will send you a CD with the corre-
sponding source code.
Linotype, Frutiger and Univers are trademarks of Linotype GmbH registered in the U.S. Patent and
Trademark Office and may be registered in certain other jurisdictions.
MHei is a trademark of The Monotype Corporation and may be registered in certain jurisdictions.
Copyright notices