Toshiba IK-WF51R User Manual
Displayed below is the user manual for IK-WF51R by Toshiba which is a product in the Security Cameras category. This manual has pages.
Related Manuals
NETWORK CAMERA
Model: IK-WF51R
User's Manual
If the URL changes, refer to the Toshiba website (http://www.toshiba.com/).
For information on our latest products and peripheral devices, refer to the
following Website:
http://www.toshibasecurity.com
2
Table of Contents
Introduction������������������������������������������������������������������������������������������������������������������������������������������������������������������ 4
ImportantSafeguards�������������������������������������������������������������������������������������������������������������������������������������������������� 6
ImportantSafeguards(Cont�)�������������������������������������������������������������������������������������������������������������������������������������� 8
NotesonUseandInstallation�������������������������������������������������������������������������������������������������������������������������������������� 9
PrecautionsforUse��������������������������������������������������������������������������������������������������������������������������������������������������� 10
PackageContents����������������������������������������������������������������������������������������������������������������������������������������������������� 11
PhysicalDescription�������������������������������������������������������������������������������������������������������������������������������������������������� 12
PhysicalDescription�������������������������������������������������������������������������������������������������������������������������������������������������� 14
Installation����������������������������������������������������������������������������������������������������������������������������������������������������������������� 17
Hardware Installation ............................................................................................................................................ 17
Network Deployment ............................................................................................................................................ 17
Software Installation ............................................................................................................................................. 19
Ready to Use ........................................................................................................................................................ 20
AccessingtheNetworkCamera�������������������������������������������������������������������������������������������������������������������������������� 21
Using Web Browsers ............................................................................................................................................ 21
IMPORTANT ......................................................................................................................................................... 21
Using RTSP Players ............................................................................................................................................. 23
Using 3GPP-compatible Mobile Devices .............................................................................................................. 24
MainPage����������������������������������������������������������������������������������������������������������������������������������������������������������������� 25
System > General settings ................................................................................................................................... 38
System > Homepage layout ................................................................................................................................ 40
System > Logs ..................................................................................................................................................... 43
System > Parameters .......................................................................................................................................... 44
System > Maintenance ......................................................................................................................................... 45
Security > User Account ....................................................................................................................................... 49
Security > HTTPS (Hypertext Transfer Protocol over SSL) ................................................................................ 50
Security > Access List ........................................................................................................................................ 55
Network > General settings .................................................................................................................................. 60
Network > Streaming protocols .......................................................................................................................... 68
Network > SNMP (Simple Network Management Protocol) ................................................................................ 75
Audio and Video > Image .................................................................................................................................. 76
Audio and Video > Stream ................................................................................................................................... 87
Audio and Video > Audio ...................................................................................................................................... 92
PTZ > PTZ settings ............................................................................................................................................. 93
Event > Event settings ......................................................................................................................................... 95
Applications > Motion detection.......................................................................................................................... 109
Applications > DI and DO ................................................................................................................................... 112
Applications > Tampering detection ................................................................................................................... 112
Applications > Audio detection ......................................................................................................................... 113
Applications > Extension Platform ...................................................................................................................... 115
Recording > Recording settings ........................................................................................................................ 117
3
Local storage > SD card management ............................................................................................................... 122
Local storage > Content management ............................................................................................................... 123
Troubleshooting������������������������������������������������������������������������������������������������������������������������������������������������������� 125
Specications���������������������������������������������������������������������������������������������������������������������������������������������������������� 126
AppearanceDiagram����������������������������������������������������������������������������������������������������������������������������������������������� 128
TechnologyLicenseNotice�������������������������������������������������������������������������������������������������������������������������������������� 129
End-userLicenseAgreementonFreeSoftwareComponentsUsedintheTOSHIBANetworkCamera���������������� 130
Trademarks�������������������������������������������������������������������������������������������������������������������������������������������������������������� 135
4
Introduction
FCC (USA)-INFORMATION
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
USER-INSTALLER CAUTION: Your authority to operate this FCC veried equipment could
be voided if you make changes or modications not expressly approved by the party.
5
Thank you for purchasing the IK-WF51R Network Camera. Before using the camera, read this
User's Manual carefully to ensure correct usage. After reading this User's Manual, save it for
future reference.
The design, specications, software, and User's Manual contents are subject to change without
prior notice.
Terms
l The term "OS" is used in this manual to indicate operating systems compatible with this
product.
-- Microsoft® Windows® 7 Professional Edition
NOTE
● The performance of the network camera may vary depending on the network environment.
● When using multiple network cameras, the appropriate network switch and PC are required.
● This camera does not support MAC-PC.
6
Important Safeguards
1. Read Instructions
Read all the safety and operating instructions before operating the product.
2. Retain Instructions
Retain the safety instructions and user's manual for future reference.
3. Warnings
Comply with all warnings on the product and in the user's manual.
4. Follow Instructions
Follow all operating and use instructions.
5. Cleaning
Disconnect this camera from the power supply before cleaning.
6. Attachments
Do not use attachments not recommended by the camera manufacturer as they may pose
safety risks.
7. Accessories
Do not place this camera on an unstable cart, stand, tripod, bracket or table. The camera
may fall, causing serious injury to a person, or serious damage to the product. Use only with
stand, tripod,bracket,or table recommended by the manufacturer, or sold with the camera.
Any mounting of the product should follow the manufacturer's instructions, and should use a
mounting accessory recommended by the manufacturer.
8. Ventilation
This camera should never be placed near or over a radiator or heat register. If this product
is placed in a built-in installation, verify that there is proper ventilation so that the camera
temperature operates within the recommended temperature range.
9. Power Sources
This camera should be operated only from the type of power source indicated on the
information label. If you are not sure of the type of power supply at your location, consult your
product dealer.
10. Power-Cord Protection
Power cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them. Pay particular attention to cords at plugs, screws and the point
where they exit the product.
11. Installation
Install this camera on a secure part of the ceiling or wall. If installed on an unsecured location,
the camera could fall causing injury and damage.
7
12. Lightning
For additional protection on this camera during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the wall outlet and disconnect the power
supply and cable system. This will prevent damage to the camera due to lightning and power-
line surges. If lightning occurs, do not touch the unit or any connected cables in order to avoid
electric shock.
13. Overloading
Do not overload the power supply or extension cords as this can result in a risk of re or
electric shock.
14. Object and Liquid Entry
Never push objects of any kind into this camera through openings as they may touch
dangerous electrical points or short-out parts that could result in a re or electrical shock.
Never intentionally spill liquid of any kind on the camera.
15. Servicing
Do not attempt to service this camera yourself as opening or removing covers may expose
you to dangerous electrical or other hazards. Refer all servicing to qualied service personnel.
16. Damage Requiring Service
Disconnect this camera from the power supply and refer servicing to qualied service
personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the camera.
c. If the camera has been submerged in water.
d. If the camera does not operate normally by following the operating instructions in the user's
manual. Adjust only those controls that are covered by the user's manual as an improper
adjustment of other controls may result in damage and will often require extensive work by a
qualied technician to restore the camera to its normal operation.
e. If the camera has been dropped or the cabinet has been damaged.
f. When the camera exhibiting a distinct change in performance which indicates a need for
service.
g. Other trouble.
17. Replacement Parts
When replacing parts, be sure the service technician uses parts specied by the manufacturer
or have the same characteristics as the original part. Unauthorized substitutions may result in
re, electric shock or other hazards.
18. Safety Check
Upon completion of any service or repairs to this camera, ask the service technician to
perform safety checks to determine that the camera is in proper operating condition.
8
Important Safeguards (Cont.)
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning ash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufcient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
FIELD INSTALLATION MARKING:
WORDED: “THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO ALL LOCAL CODES.”
This product is intended to be supplied by a Listed Power Adapter with LPS, rated PoE 42.5-
57Vdc, 0.55-0.41A : 12V DC, 2.1A.
The product is not likely to require connection to an Ethernet network with outside plant
routing, including campus environment; and the installation instructions clearly state that the
ITE is to be connected only to PoE networks without routing to the outside plant.
Ce produit est conçu pour être alimenté par un adaptateur secteur Listed avec LPS, classé
PoE 42.5-57Vdc, 0.55-0.41A : 12V DC, 2.1A.
Le produit ne est pas susceptible de nécessiter une connexion à un réseau Ethernet avec
l'extérieur routage des plantes, y compris l'environnement de campus; et les instructions
d'installation clairement que l' état ITE doit être raccordé uniquement aux réseaux PoE sans
routage vers le installations extérieures.
9
Notes on Use and Installation
l Do not aim the camera at the sun
Never aim the camera at the sun even with the camera power off.
l Do not shoot intense light
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on
the screen. However, this is not a malfunction.
l Treat the camera with care
Dropping or subjecting the camera to intense vibration may cause it to malfunction.
l Never touch internal parts
Do not touch the internal parts of the camera other than the parts specied.
l Do not submerge in water
The camera has some protection to water (see IP rating), and can be used indoors or
outdoors. If the camera was submerged in water, turn off the power and contact your dealer.
l Keep the camera installation away from video noise
If cables are wired near electric lighting wires or a TV set, noise may appear in images. In this
event relocate cables or reinstall equipment.
l Check the ambient temperature and humidity
Avoid using the camera where the temperature is hotter or colder than the specied operating
range. Doing so could affect the internal parts or cause the image quality to deteriorate.
Special care is required to use the camera at high temperature and humidity.
l Should you notice any trouble
If any trouble occurs while you are using the camera, turn off the power and contact your
dealer. If you continue to use the camera when there is something wrong with it, the trouble
may get worse and an unpredictable problem may occur.
10
Disclaimer
We disclaim any responsibility and shall be held harmless for any damages or losses
incurred by the user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether
intentional or accidental; use under extreme operating conditions.
2. Malfunction or non-function resulting in indirect, additional or consequential damages,
including but not limited to loss of expected income and suspension of business activities.
3. Incorrect use not in compliance with instructions in this user's manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modications made by the user or caused to be made by the user and carried out
by an unauthorized third party.
Notwithstanding the foregoing, Toshiba's liabilities shall not, in any circumstances, exceed the
purchase price of the product.
Copyright and Right of Portrait
There may be a conict with the Copyright Law and other laws when a customer uses, displays,
distributes, or exhibits an image picked up by the camera without permission from the copyright
holder. Please also note that transfer of an image or le covered by copyright is restricted to use
within the scope permitted by the Copyright Law.
Protection of Personal Information
Images taken by the camera that reveal the likeness of an individual person may be considered
personal information. To disclose, exhibit or transmit those images over the internet or otherwise,
consent of the person may be required.
Usage Limitation
The product is not designed for any "critical applications." "Critical applications" means life
support systems, exhaust or smoke extraction applications, medical applications, commercial
aviation, mass transit applications, military applications, homeland security applications, nuclear
facilities or systems or any other applications where product failure could lead to injury to
persons or loss of life or catastrophic property damage.
Accordingly, Toshiba disclaims any and all liability arising out of the use of the product in any
critical applications.
Precautions for Use
11
Package Contents
l IK-WF51R l Power & I/O cable
l Warranty Card l Quick Start Guide and Important
Safeguards
l Gasket / Sillica Gel and tape /
Rubber Washer / Screws and Anchors
l CD-ROM l Alignment Sticker
l Mounting Plate /
Torx driver
NETWORK CAMERA
Model: IK-WF51R
Quick Start Guide and Important Safeguards
This guide describes the hardware installation.
Refer to the user's manual (PDF le) contained in the CD-ROM for settings, operations
and other information.
The application Adobe® Reader® is needed to view PDF les. If you do not have this
application, download it from the Adobe Systems Incorporated website.
n http://www.adobe.com/
For information on our latest products and peripheral devices, refer to the following
Website:
n http://www.toshibasecurity.com
If the URL changes, refer to the Toshiba website (http://www.toshiba.com).
For Mounting Plate For Camera Base
12
Physical Description
Dome Cover
Cover Screws
IR illuminator Cover
Built-in Microphone
Clear Cover
13
l Inner View
CAMERA MAIN UNIT
Dome Cover
Cover Screws
Clear Cover Header (J7) Contacts (A)
Lens
Header (J6)
Ethernet 10/100 RJ45 Socket
Align (B) to (A) when attaching
the dome cover
MicroSD/SDHC/SDXC Card Slot
Reset
Button
Status LEDs
Contacts for IR units (B)
NOTE
Gasket for RJ45 LAN Cable
Stopper for Power & I/O cable
NOTE
White gasket is for
transportation. Don't use it
in installation.
14
Physical Description
General I/O Terminal Block
This Network Camera provides a general I/O terminal block which is used to connect
external input / output devices.
● 3.3V DC is outputted from the terminal when connected to a power supply.
The diagrams below apply when "Digital Input" is used for an alarm input.
NOTE
15
Hardware Reset
The reset button is used to reset the system or restore the factory default settings. Occasionally
resetting the system can return the camera to normal operation. If the system problems remain
after resetting, restore the factory settings and install again.
Reset:Hold for about 3 seconds and release the recessed reset button with a paper clip or small
object. Wait for the Network Camera to reboot.
Restore:Press and hold the recessed reset button until the status LED rapidly blinks. It takes
about 10 seconds. Note that all settings will be restored to factory default. Upon successful
restore, the status LED will blink during normal operation.
Status LED
The LED indicates the status of the Network Camera.
Restoring the factory defaults will erase any previous settings.
Item LED Status Description
1 Steady Red Power on and system booting
Red LED off Powered off
2 Steady Red + blinking Green every 1 sec. (Green LED on for
1 sec and off for another)
Network heartbeat
Steady Red + Green LED off Network disconnected
3 Blinking Red every 0.15 sec. + Blinking Green every 1 sec.
(Red LED on for 0.15 sec. and Green LED on for 1 sec. and
off for another)
Upgrading rmware
4 Blinking Red every 0.15 sec. + blinking Green every 0.15 sec Restoring defaults
16
SD/SDHC/SDXC Card and Capacity
This network camera is compliant with Micro SD/SDHC/SDXC 64GB and other preceding
standard Micro SD cards for local storage.
● There is a limit to the number of rewrites that is possible with the SD memory card. Replacing
the SD memory card when performing periodic maintenance of the camera is recommended.
● Do not use 512MB and below SD memory cards.
● The Camera system reserves approximately 60MB in SD memory cards. Any images are not
recordable on this space.
● Carefully read the User’s guide, precautions on use, and any other information supplied with a
purchased memory card.
● An SD memory card can be used for repeated storage. The lifespan (number of rewrites
possible) of an SD memory card is greatly affected by the capacity of the SD memory card.
● Do not use a memory card containing the data recorded by another device with the camera as
this may result in the camera not functioning correctly.
● Do not modify, overwrite the data, or change the folder name of an SD memory card. It may
result in the camera not to function correctly.
NOTE
If you Power-OFF or remove the SD memory card from camera, you have to turn
OFF the event status in Event window on page 108 and the recording status in
Recording window on page 121 preliminarily.
17
Network Deployment
In this user’s manual, “User” refers to whoever has access to the Network Camera,
and “Administrator” refers to the person who can congure the Network Camera and
grant user access to the camera.
Network Deployment is shown in the Quick Start Guide(QSG). Please refer to page 18 of the
QSG.
Setting up the Network Camera over the Internet
There are several ways to set up the Network Camera over the Internet. The rst way is to set
up the Network Camera behind a router. The second way is to utilize a static IP. The third way is
to use PPPoE.
Internet connection via a router
Before setting up the Network Camera over the Internet, make sure you have a router and follow
the steps below.
1. Connect your Network Camera behind a router, the Internet environment is illustrated below.
Regarding how to obtain your IP address, please refer to Software Installation on page 19 for
details.
Hardware Installation
Please verify that your product package contains all the accessories listed in the Package
Contents listed on page 11. Depending on the user’s application, an Ethernet cable may
be needed. The Ethernet cable should meet the specs of UTP Category 5 or higher.
Hardware Installation is shown in the Quick Start Guide(QSG). Please refer to page 13 of the
QSG.
IP address : 192.168.0.3
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
IP address : 192.168.0.2
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
LAN (Local Area Network)
Router IP address : 192.168.0.1
WAN (Wide Area Network )
Router IP address : from ISP
Cable or DSL Modem
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
Internet
This client PC sets up
a camera and a router.
Example Network Environment
Installation
18
2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is
192.168.0.3, please forward the following ports for the Network Camera on the router.
■ HTTP port: default is 80
■ RTSP port: default is 554
■ RTP port for audio: default is 5558
■ RTCP port for audio: default is 5559
■ RTP port for video: default is 5556
■ RTCP port for video: default is 5557
If you have changed the port numbers on the Network page, please open the ports accordingly
on your router. For information on how to forward ports on the router, please refer to your
router’s user’s manual.
3. Determine the public IP address of your router provided by your ISP (Internet Service
Provider). Use the public IP and the secondary HTTP port to access the Network Camera
from the Internet. Please refer to Network Type on page 60 for details.
Internet connection with static IP
Choose this connection type if you are required to use a static IP for the Network Camera.
Please refer to LAN on page 60 for details.
Internet connection via PPPoE (Point-to-Point over Ethernet)
Choose this connection type if you are connected to the Internet via a DSL Line. Please refer to
PPPoE on page 61 for details.
ADSL Modem
Internet
19
Software Installation
Installation Wizard (IW), a free-bundled software packaged in the product CD, helps to set up
your Network Camera in a LAN.
1. Install the IW under the Software Utility directory from the software CD.
Double click the IW shortcut on your desktop to launch the program.
2. The program will analyze your network environment. After your network environment is
analyzed, please click [Next] to continue the program.
3. The program will search for Network Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC and model name
which matches the MAC of the camera.
● This Software is proprietary client
software for TOSHIBA Network
Camera.
0002D1714270
IK-WR12A
Installation
Wizard
S/N: A1510XXXX
MAC: 0002D1XXXXXX
NOTE
20
Ready to Use
1. Access the Network Camera on the LAN.
2. Retrieve live video through a web browser.
21
Accessing the Network Camera
This chapter explains how to access the Network Camera through web browsers, RTSP players
and 3GPP-compatible mobile devices.
Using Web Browsers
Use Installation Wizard to access the Network Cameras on the LAN.
If your network environment is not a LAN, follow these steps to access the Network Camera:
1. Launch your web browser (Microsoft® Internet Explorer).
2. Enter the IP address of the Network Camera in the address eld. Press Enter.
3. The live video will be displayed in your web browser.
4. If it is the rst time installing the network camera, an information bar will pop up. Follow the
instructions to install the required plug-in on your computer.
IMPORTANT
► By default, the Network Camera is not password-protected. To prevent unauthorized access,
it is highly recommended to set a password for the Network Camera.
For more information about how to enable password protection, please refer to Security on
page 49.
22
► If you see a dialog box indicating that your security settings prohibit running ActiveX®
Controls, please enable the ActiveX® Controls for your browser.
1. Choose Tools > Internet Options > Security > Custom Level.
2. Look for Download signed ActiveX® controls; select Enable or Prompt. Click OK.
3. Refresh your web browser, then install the Active X® control. Follow the instructions to
complete installation.
● Currently the Network Camera utilizes 32-bit Active X® plug-in. You CAN NOT open a
Conguration/view session with the camera using a 64-bit IE browser.
NOTE
23
Using RTSP Players
To view the H.264/MPEG-4 streaming media using RTSP players, you can use players that
support RTSP streaming.
As most ISPs and players only allow RTSP streaming through port number 554, please set the
RTSP port to 554. For more information, please refer to RTSP Streaming on page 69.
For example:
4. The live video will be displayed in your player.
For more information on how to configure the RTSP access name, please refer to RTSP
Streaming on page 69 for details.
rtsp://xxx.xxx.xxx.xxx:554/live2.sdp
1. Launch the RTSP player.
2. Choose File > Open URL. A URL dialog box will pop up.
3. The address format is rtsp://<ip address>:<rtsp port>/<RTSP streaming access name for
stream1, stream2 or stream3>
24
Using 3GPP-compatible Mobile Devices
To view the streaming media through 3GPP-compatible mobile devices, make sure the Network
Camera can be accessed over the Internet. For more information on how to set up the Network
Camera over the Internet, please refer to Setup the Network Camera over the Internet on page
17.
To utilize this feature, please check the following settings on your Network Camera:
1. Because most players on 3GPP mobile phones do not support RTSP authentication, make
sure the authentication mode of RTSP streaming is set to disable.
For more information, please refer to RTSP Streaming on page 69.
2. As the bandwidth on 3G networks is limited, you will not be able to use a large video size.
Please set the video and audio streaming parameters as listed below.
Video Mode H.264
Frame size 176 x 144
Maximum frame rate 5 fps
Intra frame period 1S
Video quality (Constant bit rate) 40kbps
Audio type (GSM-AMR) 12.2kbps
3. As most ISPs and players only allow RTSP streaming through port number 554, please set
the RTSP port to 554. For more information, please refer to RTSP Streaming on page 69.
4. Launch the player on the 3GPP-compatible mobile devices.
5. Type the following URL commands into the player.
The address format is rtsp://<public ip address of your camera>:<rtsp port>/<RTSP streaming
access name for stream # with small frame size and frame rate>.
For example:
rtsp://xxx.xxx.xxx.xxx:554/live2.sdp
25
Main Page
This chapter explains the screen elements on the main page. It is composed of the following
sections: TOSHIBA Logo, Host Name, Camera Control Area, Conguration Area, and Live Video
Window.
TOSHIBA Logo
Click this logo to visit the TOSHIBA website.
Host Name
The host name can be customized to t your needs. For more information, please refer to System > General
Settings on page 38.
Camera Control Area
Display mode: This is a conguration menu exclusively designed for Panoramic cameras. Due to the
sheye lens’ wide coverage of hemispheric and panoramic views and to manipulate the details within,
the following display modes are provided:
Host name
Resize Buttons
TOSHIBA logo
Live View window
Camera Control
Area
Configuration
Area
1O - One Original hemispheric view.
1P - One Panoramic view
1R - One Regional view
1P2R - One Panoramic and two Regional views (Wall mount)
2P - Two Panoramic views
1P3R - One Panoramic and three Regional views (Wall mount)
1O3R - One Original and three Regional views
4R - Four Regional views
4R PRO - Four Regional views interactively displayed when the eld
of view changes in any of the views
1O8R - One Original and eight Regional views
* Most display modes are available in the Ceiling mount type.
26
IMPORTANT:
The Local dewarp function is designed for use with 3rd-party software that did not implement the
dewarp plug-ins. A video stream can be dewarped on the camera into a regional or panoramic
view before being sent to the client side. However, since the video has already been dewarped
into a more viewable rectilinear view, you can not exert PTZ control or change the view angle on
the client computer.
When using the Local dewarp, you should configure the view angle of a regional view in the
PTZ > PTZ settings window.
Below are the appearances of the control panel when the Local dewarp function is enabled or
disabled. The PTZ panel and the Display mode menu disappear when a video stream is using
the Local dewarp function. See page 88 for more information.
Local dewarp (on camera) Dewarp by client-side plug-ins
27
1O (Original) Display mode:
When mounted on a ceiling, the panoramic camera can
cover an approximately 50 m² surveillance area (hung
at a height of approximately 3 meters), while still keeping
details in videos with recognizable facial features of
people trafcking through the area.
The 1O view is especially adequate for taking an over-
view glimpse of surveillance area with a ceiling mount
camera.
1O View (Original View)
175° Hemispheric
Swipe to scroll horizontally
1P (Single Panoramic) Display mode:
With image correction rmware algorithms, the hemispheric image is transformed into a rectilinear stripe in the 1P display mode.
Viewers can use the PTZ panel or simply use mouse control to quickly move through the 360º panoramic view. (Mouse control
on the Panoramic view is available with the Ceiling mount type.)
Note that while the 1P view is apt for an overview, the Zoom in/out function does not apply in this mode.
IMPORTANT:
If the Local dewarp mode is selected for a video stream, the mouse control on the screen will
be disabled. For example, if stream #1 is congured into the 1R mode (see description on the
next page), its view angle will not be congurable using the mouse control.
2828
1R (Single Regional) Display mode:
The 1R mode provides access to one image section within the hemisphere. You can zoom in or out (using the mouse wheel or
PTZ panel) or travel to other areas in the hemisphere using mouse clicks and swipes. A single click on a particular object can
bring the object to the center of your view window. Click and hold down the left mouse button, and you can swipe the view both
horizontally and vertically. Double click on a view window can bring to the center of hemisphere.
1R View (Single Regional View)
Zoom in/out
&
all-directional
navigation control
Zoom In Zoom Out
2P (Dual Panoramic View) Display mode:
Similar to 1P, the 2P display mode provides simultaneous access to both the left and right sections of a hemisphere. Both
panoramic views are corrected into a more viewable dewarped image. Viewers can use a mouse click and swipe to quickly
scroll horizontally through the surveillance area.
* Note that the dividing line falls approximately on the center of the TOSHIBA logo.
2P View (Panoramic View)
Right hemi
Left hemi
Converted to rectilinear view (Dewarp)
29
1O3R (One Original & Three Regional) Display mode:
The 1O3R mode provides access to multiple live view sections within the hemisphere and the reference to their relative
positions on an Original circular view. The FOV indicators (#1 ~ #3) interact with your current operation as you may zoom in/out
or move the live view window to a different place.
You can zoom in or out or travel to other areas within the hemisphere using identical methods as previously described in the 1R
mode.
You can also change the locations of Regional views by dragging the FOV indicators on the "Original" circular view.
In a Regional view displaying 100% of video feed (via the Resize buttons - see page 32), your
mouse wheel can be used to scroll the view window vertically before you click on a live image.
After you click on the live image, the mouse wheel becomes the zoom in/out tool.
1O3R (Original & Regional) Mode Screen Control
Current screen selection
Zoom In Zoom Out
1
2
3
Interactive
regional FOV indicators
Click to bring into
center of view
Pan or tilt
O
R
R
R
3030
1O8R (One Original and Eight Regional) Display mode:
The view control and look and feel are identical to that as described in the 1O3R mode.
Note that if you change the position of a view in hemisphere, e.g., #3 window, you may lose the conguration change by
switching to another display mode. The live view window does not automatically save your view section layout.
4R (Four Regional) Display mode:
The view control and look and feel are identical to that as described in the 1O3R mode except the absence of
the Original circular view.
4R PRO (Four Regional Proactive) Display mode:
The 4R PRO mode is similar to the 4R mode except that the quad view windows consecutively rotate in correspondence to
the change of view area in one window. Note that zoom in/out and pan/tilt control in camera control area is not available in this
mode.
123
4
567
8
1
2
3
4
5
67
8
O
RRR
RRR
RR
31
Video Stream: This Network Camera supports multiple streams (stream #1 ~ #3) simultaneously. You
can select any one of them for live viewing. For more information about multiple streams, please refer to
page 88 for detailed information.
Manual Trigger: Click to manually enable or disable an event trigger. Please congure an event setting
before enabling this function. A total of 3 or 4 event settings can be congured. For more information
about event setting, please refer to page 95. If you want to hide this item on the homepage, please go
to the System > Homepage Layout > General settings > Customized button to deselect the “show
manual trigger button” checkbox.
Digital Output: Click to turn the digital output device on or off.
PTZ Control Panel:
Pano.: Click this button to start the automated circular rotation through a regional view (360° continuous
rotation). Note that this function does not apply in a Panoramic view because a Panoramic view already
shows the full coverage.
Stop: Click this button to stop the Auto Pano and Auto Rotate functions.
Pan /Tilt /Zoom /Panoramic/Rotate speed: Adjust the speed of these controls when exerted:
Note: All regional display positions and PTZ setup are not store on Home screen, and reset after change
of “Display mode” and “Mount type”.
Conguration Area
Client Settings: Click this button to access the client setting page. For more information, please refer to
Client Settings on page 35.
Conguration: Click this button to access more of the conguration options provided with the Network
Left
Down
Zoom Out
Start to Auto Pano
Stop Auto Pano
Return to Home Position
Right
Up
Zoom In
Pan speed Tilt speed Zoom speed Panoramic
speed
-5 -5 -5 - Slower
Faster
-4 -4 -4 -
-3 -3 -3 -
-2 -2 -2 -
-1 -1 -1 -
0 0 0 -
1 1 1 1
2 2 2 2
3 3 3 3
4 4 4 4
5 5 5 5
32
Live Video Window
■ The following window is displayed when the video mode is set to H.264 / MPEG-4:
Video Title: The video title can be congured. For more information, please refer to Video settings on
page 76.
H.264 / MPEG-4 Protocol and Media Options: The transmission protocol (TCP or UDP, etc.)and media
options for H.264 / MPEG-4 video streaming. For further conguration, please refer to Client Settings on
page 35.
Time: Display the current time. For further conguration, please refer to Audio and Video > Image >
General settings on page 76.
Title and Time: The video title and time can be stamped on the streaming video. For further conguration,
please refer to Audio and Video > Image > General settings on page 76.
Video and Audio Control Buttons: Depending on the Network Camera model and Network Camera
conguration, some buttons may not be available.
Camera. It is suggested that a password is applied to the Network Camera so that only the administrator
can configure the Network Camera. For more information, please refer to the description for the
Conguration menus on page 37.
Hide Button
You can click the hide button to hide the control panel or display the control panel.
Resize Buttons
:
Click the Auto button, the video cell will resize automatically to t the monitor.
Click 100% is to display the original homepage size.
Click 50% is to resize the homepage to 50% of its original size.
Click 25% is to resize the homepage to 25% of its original size.
H.264 Protocol and Media Options
Video Title Time
Title and Time Video 17:08:56 2011/10/10
2011/10/10 17:08:56
33
Snapshot: Click this button to capture and save still images. The captured images will be displayed
in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP
(*.bmp) format.
Pause: Pause the transmission of the streaming media. The button becomes the Resume button
after clicking the Pause button.
Stop: Stop the transmission of the streaming media. Click the Resume button to continue
transmission.
Start MP4 Recording: Click this button to record video clips in MP4 file format to your computer.
Press the Stop MP4 Recording button to end recording. When you exit the web browser, video
recording stops accordingly. To specify the storage destination and le name, please refer to MP4 Saving
Options on page 36 for details.
Volume: When the Mute function is not activated, move the slider bar to adjust the volume on the
local computer.
Mute: Turn off the volume on the local computer. The button becomes the Audio On button after
clicking the Mute button.
Talk: Click this button to talk to people around the Network Camera. Audio will project from
the external speaker connected to the Network Camera. Click this button again to end talking
transmission.
Mic Volume: When the Mute function is not activated, move the slider bar to adjust the
microphone volume on the local computer. Note that inernal microphone is mounted on the dome cover.
Mute: Turn off the Mic volume on the local computer. The button becomes the Mic On button
after clicking the Mute button.
Full Screen: Click this button to switch to full screen mode. Press the “Esc” key to switch back to normal
mode.
34
■ The following window is displayed when the video mode is set to MJPEG:
Video Title: The video title can be congured. For more information, please refer to Audio and Video >
Image on page 76.
Time: Display the current time. For more information, please refer to Audio and Video > Image on page
76.
Title and Time: Video title and time can be stamped on the streaming video. For more information, please
refer to Audio and Video > Image on page 76
.
Video Control Buttons: Depending on the camera model and your current conguration, some buttons
may not be available.
Snapshot: Click this button to capture and save still images. The captured images will be displayed
in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP
(*.bmp) format.
Start MP4 Recording: Click this button to record video clips in MP4 file format to your computer.
Press the Stop MP4 Recording button to end recording. When you exit the web browser, video
recording stops accordingly. To specify the storage destination and le name, please refer to MP4 Saving
Options on page 36 for details.
Full Screen: Click this button to switch to full screen mode. Press the “Esc” key to switch back to normal
mode.
Video 17:08:56 2011/03/10
Title and Time
2011/03/10 17:08:56
Time
Video (HTTP-V)
Video Title
Video Control Buttons
35
Client Settings
This chapter explains how to select the stream transmission mode and saving options on the
local computer. When completed with the settings on this page, click Save on the page bottom
to enable the settings.
H.264 / MPEG-4 Media Options
Select to stream video or audio data or both. This is enabled only when the video mode is set to H.264 or
MPEG-4..
H.264 / MPEG-4 Protocol Options
Depending on your network environment, there are four options with the transmission protocols with
H.264 or MPEG-4 streaming:
UDP unicast: This protocol allows for more real-time audio and video streams. However, network
packets may be lost due to network burst trafc and images may be broken. Activate UDP connection
when occasions require time-sensitive responses and the video quality is less important. Note that each
unicast client connecting to the server takes up additional bandwidth and the Network Camera allows up
to ten simultaneous accesses.
UDP multicast: This protocol allows multicast-enabled routers to forward network packets to all clients
requesting streaming media. This helps to reduce the network transmission load of the Network Camera
while serving multiple clients at the same time. Note that to utilize this feature, the Network Camera must
be configured to enable multicast streaming at the same time. For more information, please refer to
RTSP Streaming on page 69.
TCP: This protocol guarantees the complete delivery of streaming data and thus provides better video
quality. The downside of this protocol is that its real-time effect is not as good as that of using the UDP
protocol.
HTTP: This protocol allows the same quality as TCP protocol without needing to open specic ports for
streaming under some network environments. Users behind a rewall can utilize this protocol to allow
camera’s streaming data to pass through.
Two way audio
The half and Full-duplex modes determine the operation mode between the camera and the operator. In
Full-duplex mode, the client PC must have an audio codec capable of full-duplex functionality.
H.264/MPEG-4 Media Options
H.264/MPEG-4 Protocol Options
Two way audio
36
MP4 Saving Options
Users can record live video as they are watching it by clicking Start MP4 Recording on the main
page. Here, you can specify the storage destination and le name.
Folder: Specify a storage destination for the recorded video les.
File name prex: Enter the text that will be appended to the front of the video le name.
Add date and time sufx to the le name: Select this option to append the date and time to the end of the
le name.
Local Streaming Buffer Time
Due to unsteady bandwidth ow, live streaming may lag. If you enable this option, the live streaming will
be cached on the camera’s buffer memory before being played on the live viewing window. This helps
produce smoother live streaming. If you enter a value of 3000 milliseconds, the streaming will delay for 3
seconds.
CLIP_20100115-180853
Date and time suffix
The format is: YYYYMMDD_HHMMSS
File name prefix
37
Conguration
Click Configuration on the main page to enter the camera setting pages. Note that only
Administrators can access the conguration page.
TOSHIBA offers an easy-to-use user interface that helps you set up your network camera with
minimal effort. To simplify the setting procedure, two types of user interfaces are available:
Advanced Mode for professional users and Basic Mode for entry-level users. Some advanced
functions (PTZ/ Event/ Recording/ Local storage) are not displayed in Basic Mode.
If you want to set up advanced functions, please click on [Advanced Mode] at the bottom of the
conguration list to switch to Advanced Mode.
In order to simplify the user interface, detailed information will be hidden unless you click on the
function item. When you click on the rst sub-item, the detailed information for the rst sub-item
will be displayed; when you click on the second sub-item, the detailed information for the second
sub-item will be displayed and that of the rst sub-item will be hidden.
The following is the interface of the Basic Mode and the Advanced Mode:
Basic Mode
Configuration List
Click to switch to Advanced Mode
Navigation Area
Firmware Version
Panoramic camera
38
Advanced Mode
Each function on the conguration list will be explained in the following sections. Those functions that are
displayed only in Advanced Mode are marked with Advanced Mode . If you want to set up advanced
functions, please click on [Advanced Mode] at the bottom of the conguration list.
The Navigation Area provides access to all different views from the Home page (for live viewing) and
Conguration page.
System > General settings
This section explains how to congure the basic settings for the Network Camera, such as the
host name and system time. It is composed of the following two columns: System and System
Time.
System
Host name: Enter a desired name for the Network Camera. The name will be displayed at the top center
of the main page.
Turn off the LED indicator : To disable the status LED light, uncheck this option.
Configuration List
Click to switch to Basic Mode
Firmware Version
Navigation Area
Panoramic camera
39
System time
Keep current date and time: Select this option to preserve the current date and time of the Network
Camera. The Network Camera’s internal real-time clock maintains the date and time even when the
power of the system is turned off.
Synchronize with computer time: Select this option to synchronize the date and time of the Network
Camera with the local computer. The read-only date and time of the PC is displayed as updated.
Manual: The administrator can enter the date and time manually. Note that the date and time format are
[yyyy/mm/dd] and [hh:mm:ss].
Automatic: The Network Time Protocol is a protocol which synchronizes computer clocks by periodically
querying an NTP Server.
NTP server: Assign the IP address or domain name of the time-server. Leaving the text box blank
connects the Network Camera to the default time servers.
Update interval: Select to update the time using the NTP server on an hourly, daily, weekly, or monthly
basis.
Time zone Advanced Mode : Select the appropriate time zone from the list. If you want to upload
Daylight Savings Time rules, please refer to System > Maintenance > Import/ Export les on page 46
for details.
When nished with the settings on this page, click Save at the bottom of the page to enable the settings.
40
System > Homepage layout Advanced Mode
This section explains how to set up your own customized homepage layout.
General settings
This column shows the settings of your hompage layout. You can manually select the background and
font colors in Theme Options (the second tab on this page). The settings will be displayed automatically
in this Preview eld. The following shows the homepage using the default settings:
Logo graph
Here you can change the logo at the top of your homepage.
Follow the steps below to upload a new logo:
1. Click Custom and the Browse eld will appear.
2. Select a logo from your les.
3. Click Upload to replace the existing logo with a new one.
4. Enter a website link if necessary.
5. Click Save to enable the settings.
Customized button
If you want to hide manual trigger buttons on the homepage, please uncheck this item. This item is
checked by default.
41
Theme Options
Here you can change the color of your homepage layout. There are three types of preset patterns for you
to choose from. The new layout will simultaneously appear in the Preview led. Click Save to enable the
settings.
Font Color of the
Video Title
Background Color of
the Video Area
Frame Color
Font Color
Background Color of the
Control Area
Font Color of the
Configuration Area
Background Color of the
Configuration Area
Preset patterns
42
■ Follow the steps below to set up a custom homepage:
1. Click Custom on the left column.
2. Click to select a color on on the right column.
3. The palette window will pop up as shown below.
4. Drag the slider bar and click on the left square to select a desired color.
5. The selected color will be displayed in the corresponding elds and in the Preview column.
6. Click Save to enable the settings.
1
23
4
Color Selector
Custom
Pattern
43
System > Logs Advanced Mode
This section explains how to configure the Network Camera to backup the system log to a
remote server.
Log server settings
Follow the steps below to set up the remote log:
1. Select Enable remote log.
2. In the IP address text box, enter the IP address of the remote server.
2. In the port text box, enter the port number of the remote server.
3. When completed, click Save to enable the setting.
You can congure the Network Camera to send the system log le to a remote server as a log message.
When using this feature, the appropriate syslog server is required for receiving the system log message
from the Network Camera.
System log
This column displays the system log in chronological order. The system log is stored in the Network
Camera’s buffer and dated events will be overwritten when the number of events reaches a limit.
The system log messages stored in the Network Camera will be all cleared after reboot or power down
the Network Camera.
44
Access log
Access log displays the access time and IP address of all viewers (including operators and
administrators) in chronological order. The access log is stored in the Network Camera’s buffer and older
events will be overwritten when the number of events reaches a limit.
The access log messages stored in the Network Camera will be all cleared after reboot or power down
the Network Camera.
System > Parameters Advanced Mode
The View Parameters page lists the entire system’s parameters in an alphabetical order. If you
need technical assistance, please provide the information listed on this page.
45
System > Maintenance
This chapter explains how to restore the Network Camera to factory default, upgrade rmware
version, etc.
General settings > Upgrade rmware
This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to
complete the process.
Note: Do not power off the Network Camera during the upgrade!
Follow the steps below to upgrade the rmware:
1. Download the latest rmware le from the TOSHIBA website. The le is in .pkg le format.
2. Click Browse… and specify the rmware le.
3. Click Upgrade. The Network Camera starts to upgrade and will reboot automatically when the upgrade
completes.
If the upgrade is successful, you will see “Reboot system now!! This connection will close”. After that, re-
access the Network Camera.
The following message is displayed when the upgrade has succeeded.
The following message is displayed when you have selected an incorrect rmware le.
General settings > Reboot
This feature allows you to reboot the Network Camera, which takes about one minute to complete. When
completed, the live video page will be displayed in your browser. The following message will be displayed
during the reboot process.
If the connection fails after rebooting, manually enter the IP address of the Network Camera in the
address eld to resume the connection.
Firmware file:
Starting firmware upgrade...
Do not power down the server during the upgrade.
The server will restart automatically after the upgrade is
completed.
This will take about 1 - 5 minutes.
Invalid firmware version
Unpack fail...system is rebooting...
Reboot system now!!
This connection will close.
46
General settings > Restore
This feature allows you to restore the Network Camera to factory default settings.
Network: Select this option to retain the Network Type settings (please refer to Network Type on page
60).
Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to
Import/Export les below on this page).
If none of the options is selected, all settings will be restored to factory default. The following message is
displayed during the restoring process.
Import/Export les Advanced Mode
This feature allows you to Export / Update daylight saving time rules, custom language file, and
conguration le.
Export daylight saving time conguration le: Click to set the start and end time of DST.
Follow the steps below to export:
1. In the Export les column, click Export to export the daylight saving time conguration le from the
Network Camera.
2. A le download dialog will pop up as shown below. Click Open to review the XML le or click Save to
store the le for editing.
47
3. Open the le with text editor and locate your time zone; set the start and end time of DST. When
completed, save the le.
In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at
2:00 a.m. on the rst Sunday in November.
Update daylight saving time rules: Click Browse… and specify the XML le to update.
If incorrect date and time are assigned, you will see the following warning message when uploading the
le to the Network Camera.
48
The following message is displayed when attempting to upload an incorrect le format.
Export conguration le: Click to export all parameters for the device and user-dened scripts.
Update conguration le: Click Browse… to update a conguration le. Please note that the model and
rmware version of the device should be the same as the conguration le. If you have set up a xed IP
or other special settings for your device, it is not suggested to update a conguration le.
Export server staus report: Click to export the current server status report, such as time, logs,
parameters, process status, memory status, le system status, network status, kernel message..., and so
on.
49
Security > User Account
This section explains how to enable password protection and create multiple accounts.
Root Password
The administrator account name is “root”, which is permanent and can not be deleted. If you want to add
more accounts in the Manage User column, please apply the password for the “root” account rst.
1. Type the password identically in both text boxes, then click Save to enable password protection.
2. A window will prompt for authentication; type the correct user’s name and password in their respective
elds to access the Network Camera.
Note:
* Leaving the root password eld empty means the camera will not be protected by password.
Privilege management Advanced Mode
Digital Output & PTZ control: You can modify the management privilege as operators or viewers. Select
or de-select the checkboxes, and then click Save to enable the settings. If you give Viewers the privilege,
Operators will also have the ability to control the Network Camera through the main page. (Please refer
to Conguration on page 31).
Allow anonymous viewing: If you check this item, 3GPP clients can access the live stream without
entering a User ID and Password.
Note:
* Select RTSP Streaming Authentication to disable.
* This function will not work with Internet Explorer.
Account management
Administrators can create up to 20 user accounts.
1. Input the new user’s name and password.
2. Select the privilege level for the new user account. Click Add to enable the setting.
Access rights are sorted by user privilege (Administrator, Operator, and Viewer). Only administrators can
access the Conguration page. Though operators cannot access the Conguration page, they can use
the URL Commands to get and set the value of parameters. For more information, please refer to URL
Command Guide. Viewers access only the main page for live viewing.
Here you also can change a user’s access rights or delete user accounts.
1. Select an existing account to modify.
2. Make necessary changes and click Update or Delete to enable the setting.
50
Security > HTTPS (Hypertext Transfer Protocol over SSL)
This section explains how to enable authentication and encrypted communication over SSL
(Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher
security level.
Create and Install Certicate Method
Before using HTTPS for communication with the Network Camera, a Certicate must be created rst.
There are two ways to create and install a certicate:
Create self-signed certificate
1.Select this option from a pull-down menu.
2. In the rst column, select Enable HTTPS secure connection, then select a connection option: “HTTP
& HTTPS” or “HTTPS only”.
3.Click Create certicate to generate a certicate.
4. The Certicate Information will automatically be displayed as shown below. You can click Certi cate
properties to view detailed information about the certicate.
Advanced Mode
51
5. Click Home to return to the main page. Change the address from “http://” to “https://“ in the address
bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to
enable HTTPS.
https://192.168.5.151/index.html
https://
52
Create certificate request and install :Select this option if you want to create a certicate from a
certicate authority.
1. Select this option from a method pull-down menu.
2. Click Create certicate to generate the certicate.
53
3. If you see the following Information bar, click OK and click on the Information bar at the top of the page
to allow pop-ups.
4. The pop-up window shows an example of a certicate request.
5. Look for a trusted certificate authority that issues digital certificates. Enroll the Network Camera.
Wait for the certificate authority to issue a SSL certificate; click Browse... to search for the issued
certicate, then click Upload in the column.
54
● 1. How do I cancel the HTTPS settings?
1-1. Click on the Remove certicate button.
1-2. The webpage will redirect to a non-HTTPS page automatically.
● 2. If you want to create and install other certicates, please remove the existing one.
Enable HTTPS
Check this item to enable HTTPS communication, then select a connection option: ”HTTP &
HTTPS” or “HTTPS only”. Note that you have to create and install a certicate rst before
clicking the Save button.
NOTE
55
Security > Access List
This section explains how to control access permission by verifying the client PC’s IP address.
General Settings
Maximum number of concurrent streaming: Simultaneous live viewing for 1~10 clients (including stream
1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will
be disconnected and automatically attempt to re-link.
Connection management: Click this button to display the connection status window showing a list of the
current connections. For example:
Note that only consoles that are currently displaying live streaming will be listed in the Connection
management list.
■ IP address: Current connections to the Network Camera.
■ Elapsed time: How much time the client has been at the webpage.
■ User ID: If the administrator has set a password for the webpage, the clients have to enter a user name
and password to access the live video. The user name will be displayed in the User ID column. If the
administrator allows clients to link to the webpage without a user name and password, the User ID
column will be empty.
There are some situations that allow clients access to the live video without a user name and
password:
1. The administrator does not set up a root password. For more information about how to set up a root
password and manage user accounts, please refer to Security > User account on page 49.
2. The administrator has set up a root password, but set RTSP Authentication to “disable“. For more
information about RTSP Authentication, please refer to RTSP Streaming on page 69.
3. The administrator has set up a root password, but allows anonymous viewing. For more information
about Allow Anonymous Viewing, please refer to page 49.
56
■ Refresh: Click this button to refresh all current connections.
■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List
to deny access. Please note that those checked connections will only be disconnected temporarily
and will automatically try to re-link again (IE Explore or Quick Time Player). If you want to enable the
denied list, please check Enable access list ltering and click Save in the rst column.
■ Disconnect: If you want to break off the current connections, please select them and click this
button. Please note that those checked connections will only be disconnected temporarily and will
automatically try to re-link again (IE Explore or Quick Time Player).
Filter
Enable access list ltering: Check this item and click Save if you want to enable the access list ltering
function.
Filter type: Select Allow or Deny as the lter type. If you choose Allow Type, only those clients whose
IP addresses are on the Access List below can access the Network Camera, and the others cannot. On
the contrary, if you choose Deny Type, those clients whose IP addresses are on the Access List below
will not be allowed to access the Network Camera, and the others access.
Then you can Add a rule to the following Access List. Please note that the IPv6 access list column
will not be displayed unless you enable IPv6 on the Network page. For more information about IPv6
Settings, please refer to Network > General settings on page 64 for detailed information.
57
Network: This rule allows the user to assign a network address and corresponding subnet mask to the
Allow/Deny List. The address and network mask are written in CIDR format.
For example:
Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List.
Note: This rule only applies to IPv4 addresses.
For example:
Administrator IP address
Always allow the IP address to access this device: You can check this item and add the Administrator’s
IP address in this eld to make sure the Administrator can always connect to the device.
IP address range 192.168.2.x will be blocked.
There are three types of rules:
Single: This rule allows the user to add an IP address to the Allowed/Denied list.
For example:
192.168.2.1
58
Security > IEEE 802.1x Advanced Mode
Enable this function if your network environment uses IEEE 802.1x, which is a port-based network
access control. The network devices, intermediary switch/access point/hub, and RADIUS server must
support and enable 802.1x settings.
The 802.1x standard is designed to enhance the security of local area networks, which provides
authentication to network devices (clients) attached to a network port (wired or wireless). If all certicates
between client and server are veried, a point-to-point connection will be enabled; if authentication fails,
access on that port will be prohibited. 802.1x utilizes an existing protocol, the Extensible Authentication
Protocol (EAP), to facilitate communication.
■ The components of a protected network with 802.1x authentication:
1. Supplicant: A client end user (camera), which requests authentication.
2. Authenticator (an access point or a switch): A “go between” which restricts unauthorized end users
from communicating with the authentication server.
3. Authentication server (usually a RADIUS server): Checks the client certicate and decides whether to
accept the end user’s access request.
■ Network Cameras support two types of EAP methods to perform authentication: EAP-PEAP and EAP-
TLS.
Please follow the steps below to enable 802.1x settings:
1. Before connecting the Network Camera to the protected network with 802.1x, please apply a digital
certicate from a Certicate Authority (ie. MIS of your company) which can be validated by a RADIUS
server.
2. Connect the Network Camera to a PC or notebook outside of the protected LAN. Open the
conguration page of the Network Camera as shown below. Select EAP-PEAP or EAP-TLS as the
EAP method. In the following blanks, enter your ID and password issued by the CA, then upload
related certicate(s).
Supplicant
(Network Camera)
Authenticator
(Network Switch)
Authentication Server
(RADIUS Server)
59
3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to
an 802.1x enabled switch. The devices will then start the authentication automatically.
● The maximum length of password is 200 symbols.
● The authentication process for 802.1x:
1. The Certicate Authority (CA) provides the required signed certicates to the Network Camera
(the supplicant) and the RADIUS Server (the authentication server).
2. A Network Camera requests access to the protected LAN using 802.1X via a switch (the
authenticator). The client offers its identity and client certificate, which is then forwarded
by the switch to the RADIUS Server, which uses an algorithm to authenticate the Network
Camera and returns an acceptance or rejection back to the switch.
3. The switch also forwards the RADIUS Server’s certicate to the Network Camera.
4. Assuming all certicates are validated, the switch then changes the Network Camera’s state
to authorized and is allowed access to the protected network via a pre-congured port.
Network Camera
RADIUS Server
Certificate Authority
(CA)
Protected LAN
Certificate
1
1
2
3
4
Network Switch
Certificate
NOTE
60
Network > General settings
This section explains how to congure a wired network connection for the Network Camera.
Network Type
LAN
Select this option when the Network Camera is deployed on a local area network (LAN) and is intended
to be accessed by local computers. The default setting for the Network Type is LAN. Rememer to click
Save when you complete the Network setting.
Get IP address automatically: Select this option to obtain an available dynamic IP address assigned by
the DHCP server each time the camera is connected to the LAN.
Use xed IP address: Select this option to manually assign a static IP address to the Network Camera.
1. You can use Installation Wizard on the software CD to easily set up the Network
Camera on LAN. Please refer to Software Installation on page 19 for details.
2. Enter the Static IP, Subnet mask, Default router, and Primary DNS provided by your ISP.
Subnet mask: This is used to determine if the destination is in the same subnet. The default value is
“255.255.255.0”.
Default router: This is the gateway used to forward frames to destinations in a different subnet. Invalid
router setting will fail to send the transmission to destinations in different subnets.
61
Primary DNS: The primary domain name server that translates hostnames into IP addresses.
Secondary DNS: Secondary domain name server that backups the Primary DNS.
Primary WINS server: The primary WINS server that maintains the database of computer name and IP
address.
Secondary WINS server: The secondary WINS server that maintains the database of computer name
and IP address.
Enable UPnP presentation: Select this option to enable UPnPTM presentation for your Network Camera
so that whenever a Network Camera is presented to the LAN, shortcuts of connected Network Cameras
will be listed in My Network Places. You can click the shortcut to link to the web browser. Currently,
UPnPTM is supported by Windows XP or later. Note that to utilize this feature, please make sure the
UPnPTM component is installed on your computer.
Enable UPnP port forwarding: To access the Network Camera from the Internet, select this option to
allow the Network Camera to open ports on the router automatically so that video streams can be sent
out from a LAN. To utilize of this feature, make sure that your router supports UPnPTM and it is activated.
PPPoE (Point-to-point over Ethernet)
Select this option to congure your Network Camera to make it accessible from anywhere as long as
there is an Internet connection. Note that to utilize this feature, it requires an account provided by your
ISP (service provider).
Follow the steps below to acquire your Network Camera’s public IP address.
1. Set up the Network Camera on the LAN.
2. Go to Conguration > Event > Event settings > Add server (please refer to Add server on page 100) to
add a new email or FTP server.
3. Go to Conguration > Event > Event settings > Add media (please refer to Add media on page 105).
Select System log so that you will receive the system log in TXT le format which contains the
Network Camera’s public IP address in your email or on the FTP server.
4. Go to Conguration > Network > General settings > Network type. Select PPPoE and enter the user
name and password provided by your ISP. Click Save to enable the setting.
5. The Network Camera will reboot.
6. Disconnect the power to the Network Camera; remove it from the LAN environment.
Network Camera (192.168.5.151)
Network Camera (192.168.5.128)
Network Camera (192.168.5.141)
62
● If the default ports are already used by other devices connected to the same router, the
Network Camera will select other ports for the Network Camera.
● If UPnPTM is not supported by your router, you will see the following message:
Error: Router does not support UPnP port forwarding.
● Below are steps to enable the UPnPTM user interface on your computer:
Note that you must log on to the computer as a system administrator to install the UPnPTM
components.
1. Go to Start, click Control Panel, then click Add or Remove Programs.
2. In the Add or Remove Programs dialog box, click Add/Remove Windows Components.
3.
In the Windows Components Wizard dialog box, select Networking Services and click
Details.
NOTE
63
4. In the Networking Services dialog box, select Universal Plug and Play and click OK.
5. Click Next in the following window.
6. Click Finish. UPnPTM is enabled.
● How does UPnPTM work?
UPnPTM networking technology provides automatic IP conguration and dynamic discovery of
devices added to a network. Services and capabilities offered by networked devices, such as
printing and le sharing, are available among each other without the need for cumbersome
network configuration. In the case of Network Cameras, you will see Network Camera
shortcuts under My Network Places.
● Enabling UPnP port forwarding allows the Network Camera to open a secondary HTTP port
on the router-not HTTP port-meaning that you have to add the secondary HTTP port number
to the Network Camera’s public address in order to access the Network Camera from the
Internet. For example, when the HTTP port is set to 80 and the secondary HTTP port is set to
8080, refer to the list below for the Network Camera’s IP address.
From the Internet In LAN
http://203.67.124.123:8080 http://192.168.4.160 or
http://192.168.4.160:8080
● If the PPPoE settings are incorrectly congured or the Internet access is not working, restore
the Network Camera to factory default; please refer to Restore on page 46 for details. After
the Network Camera is reset to factory default, it will be accessible on the LAN.
64
Enable IPv6
Select this option and click Save to enable IPv6 settings.
Please note that this only works if your network environment and hardware equipment support IPv6. The
browser should be Microsoft® Internet Explorer 6.5 or above.
When IPv6 is enabled, by default, the network camera will listen to router advertisements and be
assigned with a link-local IPv6 address accordingly.
IPv6 Information: Click this button to obtain the IPv6 information as shown below.
If your IPv6 settings are successful, the IPv6 address list will be listed in the pop-up window. The IPv6
address will be displayed as follows:
Link-global IPv6 address/network mask
Link-local IPv6 address/network mask
Refers to Ethernet
65
Please follow the steps below to link to an IPv6 address:
1. Open your web browser.
2. Enter the link-global or link-local IPv6 address in the address bar of your web browser.
3. The format should be:
4. Press Enter on the keyboard or click Refresh button to refresh the webpage.
For example:
● If you have a Secondary HTTP port (the default value is 8080), you can also link to the webpage in
the following address format: (Please refer to HTTP streaming on page 68 for detailed information.)
● If you choose PPPoE as the Network Type, the [PPP0 address] will be displayed in the IPv6
information column as shown below.
Manually setup the IP address: Select this option to manually set up IPv6 settings if your network
environment does not have DHCPv6 server and router advertisements-enabled routers.
If you check this item, the following blanks will be displayed for you to enter the corresponding
information:
http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/
IPv6 address
http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/:8080
IPv6 address Secondary HTTP port
NOTE
66
Port
HTTPS port: By default, the HTTPS port is set to 443. It can also be assigned to another port number
between 1025 and 65535.
Two way audio port: By default, the two way audio port is set to 5060. Also, it can also be assigned to
another port number between 1025 and 65535.
The Network Camera supports two way audio communication so that operators can transmit and receive
audio simultaneously. By using the Network Camera’s built-in or external microphone and an external
speaker, you can communicate with people around the Network Camera.
Note that as JPEG only transmits a series of JPEG images to the client, to enable the two-way audio
function, make sure the video mode is set to H.264 on the Audio and Video > Stream > Stream settings
page and the media option is set to "Video and Audio" on the Client Settings page. Please refer to Client
Settings on page 35 and Stream settings on page 88.
Audio transmitted from operators
Audio transmitted to operators
67
Click to enable audio transmission to the Network Camera; click to adjust the volume of
microphone; click to turn off the audio. To stop talking, click again.
FTP port: The FTP server allows the user to save recorded video clips. You can use TOSHIBA Installation
Wizard software to upgrade the rmware via FTP server. By default, the FTP port is set to 21. It also can
be assigned to another port number between 1025 and 65535.
Video (TCP-AV)
Audio is being transmitted to the Network Camera
Talk Button
Volume Mute
68
Network > Streaming protocols Advanced Mode
HTTP streaming
To utilize HTTP authentication, make sure that your have set a password for the Network Camera rst;
please refer to Security > User account on page 49 for details.
Authentication: Depending on your network security requirements, the Network Camera provides two
types of security settings for an HTTP transaction: basic and digest.
If basic authentication is selected, the password is sent in plain text format and there can be potential
risks of being intercepted. If digest authentication is selected, user credentials are encrypted using MD5
algorithm and thus provide better protection against unauthorized accesses.
HTTP port / Secondary HTTP port: By default, the HTTP port is set to 80 and the secondary HTTP port is
set to 8080. They can also be assigned to another port number between 1025 and 65535. If the ports are
incorrectly assigned, the following warning messages will be displayed:
To access the Network Camera on the LAN, both the HTTP port and secondary HTTP port can be used
to access the Network Camera. For example, when the HTTP port is set to 80 and the secondary HTTP
port is set to 8080, refer to the list below for the Network Camera’s IP address.
Access name for stream 1 ~ 3: This Network camera supports multiple streams simultaneously. The
access name is used to differentiate the streaming source. Users can click Audio and Video > Stream >
Stream settings to set up the video quality of linked streams. For more information about how to set up
the video quality, please refer to Stream settings on page 88.
On the LAN
http://192.168.4.160 or
http://192.168.4.160:8080
69
RTSP Streaming
To utilize RTSP streaming authentication, make sure that you have set a password for the Network
Camera rst; please refer to Security > User account on page 49 for details.
70
Authentication: Depending on your network security requirements, the Network Camera provides three
types of security settings for streaming via RTSP protocol: disable, basic, and digest.
If basic authentication is selected, the password is sent in plain text format, but there can be potential
risks of it being intercepted. If digest authentication is selected, user credentials are encrypted using
MD5 algorithm, thus providing better protection against unauthorized access.
Access name for stream 1 ~ 3: This Network camera supports multiple streams simultaneously. The
access name is used to differentiate the streaming source.
If you want to use an RTSP player to access the Network Camera, you have to set the video mode to
H.264 and use the following RTSP URL command to request transmission of the streaming data.
rtsp://<ip address>:<rtsp port>/<access name for stream1 ~ 3>
For example, when the access name for stream 1 is set to live.sdp:
1. Launch an RTSP player.
2. Choose File > Open URL. A URL dialog box will pop up.
3. Type the above URL command in the address eld.
4. The live video will be displayed in your player.
RTSP port /RTP port for video, metadata, audio/ RTCP port for video, metadata, audio
■ RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default, the port
number is set to 554.
■ The RTP (Real-time Transport Protocol) is used to deliver video metadata, and audio data to the
clients. By default, the RTP port for video is set to 5556 , RTP port for metadata is set to 6556 and the
RTP port for audio is set to 5558.
■ The RTCP (Real-time Transport Control Protocol) allows the Network Camera to transmit the data by
monitoring the Internet trafc volume. By default, the RTCP port for video is set to 5557, the RTCP port
for metadata is set to 6557 and the RTCP port for audio is set to 5559.
The ports can be changed to values between 1025 and 65535. The RTP port must be an even number
and the RTCP port is the RTP port number plus one, and thus is always an odd number. When the RTP
port changes, the RTCP port will change accordingly.
If the RTP ports are incorrectly assigned, the following warning message will be displayed:
rtsp://192.168.5.151:554/live.sdp
71
Multicast settings for stream 1 ~ 3: Click the items to display the detailed configuration information.
Select the Always multicast option to enable multicast for stream 1 ~ 3.
Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other
hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at
the same time by requesting a copy from the multicast group address. Therefore, enabling multicast can
effectively save Internet bandwith.
The ports can be changed to values between 1025 and 65535. The multicast RTP port must be an even
number and the multicast RTCP port number is the multicast RTP port number plus one, and thus is
always odd. When the multicast RTP port changes, the multicast RTCP port will change accordingly.
If the multicast RTP video ports are incorrectly assigned, the following warning message will be
displayed:
Multicast TTL [1~255]: The multicast TTL (Time To Live) is the value that tells the router the range a
packet can be forwarded.
Initial TTL Scope
0 Restricted to the same host
1 Restricted to the same subnetwork
32 Restricted to the same site
64 Restricted to the same region
128 Restricted to the same continent
255 Unrestricted in scope
72
Network > DDNS
This section explains how to configure the dynamic domain name service for the Network
Camera. DDNS is a service that allows your Network Camera, especially when assigned with a
dynamic IP address, to have a xed host and domain name.
DDNS: Dynamic domain name service
Enable DDNS: Select this option to enable the DDNS setting.
Provider: The provider list contains seven hosts that provide DDNS service. Please connect to the
service provider’s web site to review the service charges and sign-up for the service if you want to use
DDNS.
ChangeIP.com
http://www.changeip.com/toshiba/
No-IP.com
http://www.no-ip.com/ext/toshiba.php
Host Name: If the User wants to use a DDNS service, enter the camera name that is registered at the
DDNS server.
User Name: The User Name eld is necessary for logging into the DDNS server or to notify the User of
the new IP address.
Note: When this eld is input as “User Name”, the following eld nust be input as “Password”.
Password: Input the password to access the DDNS service.
Save: Click on this button to save current settings for the DDNS service.
73
Network > QoS (Quality of Service) Advanced Mode
Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality
to different services on the network. Quality of service guarantees are important if the network capacity
is insufcient, especially for real-time streaming multimedia applications. Quality can be dened as, for
instance, a maintained level of bit rate, low latency, no packet dropping, etc.
The following are the main benets of a QoS-aware network:
■ The ability to prioritize trafc and guarantee a certain level of performance to the data ow.
■ The ability to control the amount of bandwidth each application may use, and thus provide higher
reliability and stability on the network.
Requirements for QoS
To utilize QoS in a network environment, the following requirements must be met:
■ All network switches and routers in the network must include support for QoS.
■ The network video devices used in the network must be QoS-enabled.
QoS models
CoS (the VLAN 802.1p model)
IEEE802.1p defines a QoS model at OSI Layer 2 (Data Link Layer), which is called CoS, Class of
Service. It adds a 3-bit value to the VLAN MAC header, which indicates the frame priority level from 0
(lowest) to 7 (highest). The priority is set up on the network switches, which then use different queuing
disciplines to forward the packets.
Below is the setting column for CoS. Enter the VLAN ID of your switch (0~4095) and choose the priority
for each application (0~7).
If you assign Video the highest priority level, your network switch will handle video packets rst.
● A VLAN Switch (802.1p) is required. Web browsing may fail if the CoS setting is incorrect.
● Class of Service technologies do not guarantee a level of service in terms of bandwidth and
delivery time; they offer a “best-effort.” Users can think of CoS as “coarsely-grained” traffic
control and QoS as “nely-grained” trafc control.
● Though CoS is simple to manage, it lacks scalability and does not offer end-to-end guarantees
since it is based on L2 protocol.
NOTE
74
QoS/DSCP (the DiffServ model)
DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is
based on packet marking and router queuing disciplines. The marking is done by adding a eld to the
IP header, called the DSCP (Differentiated Services Codepoint). This is a 6-bit field that provides 64
different class IDs. It gives an indication of how a given packet is to be forwarded, known as the Per Hop
Behavior (PHB). The PHB describes a particular service level in terms of bandwidth, queueing theory,
and dropping (discarding the packet) decisions. Routers at each network node classify packets according
to their DSCP value and give them a particular forwarding treatment; for example, how much bandwidth
to reserve for it.
Below are the setting options of DSCP (DiffServ Codepoint). Specify the DSCP value for each application
(0~63).
75
Network > SNMP (Simple Network Management Protocol)
Advanced Mode
This section explains how to use the SNMP on the network camera. The Simple Network
Management Protocol is an application layer protocol that facilitates the exchange of
management information between network devices. It helps network administrators to remotely
manage network devices and nd, solve network problems with ease.
■ The SNMP consists of the following three key components:
1. Manager: Network-management station (NMS), a server which executes applications that monitor and
control managed devices.
2. Agent: A network-management software module on a managed device which transfers the status of
managed devices to the NMS.
3. Managed device: A network node on a managed network. For example: routers, switches, bridges,
hubs, computer hosts, printers, IP telephones, network cameras, web server, and database.
Before conguring SNMP settings on the this page, please enable your NMS rst.
SNMP Conguration
Enable SNMPv1, SNMPv2c
Select this option and enter the names of Read/Write community and Read Only community according to
your NMS settings.
Enable SNMPv3
This option contains cryptographic security, a higher security level, which allows you to set the
Authentication password and the Encryption password.
■ Security name: According to your NMS settings, choose Read/Write or Read Only and enter the
community name.
■ Authentication type: Select MD5 or SHA as the authentication method.
■ Authentication password: Enter the password for authentication (at least 8 characters).
■ Encryption password: Enter a password for encryption (at least 8 characters).
76
Audio and Video > Image Advanced Mode
This section explains how to congure the image settings of the Network Camera. It is composed of the following
four columns: General settings, Preference, Exposure, Zoom and Focus, and Privacy mask.
General settings
Video title: Enter a name that will be displayed on the title bar of the live video as the picture shown below.
Show timestamp and video title in video and snapshots: Enter a name that will be displayed on the title bar of the
live video as the picture shown below. (Note: It may be unable to display with restriction of a dewarp function.)
Mount type: There are 3 Mount types - Ceiling, Wall, and Floor.
Ceiling: The Ceiling mount type automatically delivers upside-down images. The Ceiling mode
supports the following Display modes - 1O, 1P, 1R, 2P, 1O3R, 4R, 4R PRO, and 1O8R.
Wall: The Wall mount type applies to the monitoring of long, side-to-side surveillance areas, such
as when mounted on a wall facing a corridor. Different Mount types have different options with the
Display mode settings. For example, the 1P2R (1 Panoramic & 2 Regional) and 1P3R (1 Panoramic & 3 Regional)
display modes are only available when the “Wall“ Mount type is applied.
Floor: The Display modes with the Floor mount type are identical to those for the Ceiling mount
except that the images are not vertically ipped.
Position of timestamp and video title on image: Select to display time stamp and video title on the top or at the
bottom of the video stream.
Timestamp and video title font size: Select the font size for the time stamp and title.
Video 17:55:49 2015/12/6
Title and Time
Video (TCP-AV)
Video Title
Color: Select to display color or black/white video streams.
Power line frequency: Set the power line frequency consistent with local utility settings to eliminate image
flickering associated with fluorescent lights. Note that after the power line frequency is changed, you must
disconnect and reconnect the power cord of the Network Camera in order for the new setting to take effect.
77
Video orientation:
Flip - vertically reect the display of the live video;
Mirror - horizontally reect the display of the live video. Select both options if the Network Camera is
installed upside-down (e.g., on the ceiling) to correct the image orientation. Please note that if you have
preset locations, those locations will be cleared after ip/mirror setting.
78
Day/Night
Switch to B/W in night mode
Select this checkbox to enable the Network Camera to automatically switch to Black & White display
during the night mode.
Turn on external IR illuminator in night mode
Select this to turn on an external IR illuminator (connected via Digital Output lines) when the camera
detects low light condition and enters the night mode.
Turn on built-in IR illuminator in night mode
Select this to turn on the built-in IR illuminators when the camera detects low light condition and enters
the night mode.
IR cut lter
With a removable IR-cut lter, this Network Camera can automatically remove the lter to let Infrared light
pass into the sensor during low light conditions.
■ Auto mode
The Network Camera automatically removes the IR cut lter by judging the level of ambient light. Make
sure the setup of Sensitivity to t situation.
Note:
The Prole setting in Exposure will disable when Auto mode is selected.
■ Day mode
In day mode, the Network Camera switches on the IR cut lter at all times to block infrared light from
reaching the sensor so that the colors will not be distorted.
■ Night mode
In night mode, the Network Camera switches off the IR cut lter at all times for the sensor to accept
infrared light, thus helping to improve low light sensitivity.
■ Synchronize with digital input
The Network Camera automatically removes the IR cut lter when DI triggers For
example, when the camera is accompanied by an external IR light that comes with its own sensor and
provides a signal to the camera. Some camera housings come with such mechanism.
■ Schedule mode
The Network Camera switches between day mode and night mode based on a specied schedule.
Enter the start and end time for day mode. Note that the time format is [hh:mm] and is expressed in
24-hour clock time. By default, the start and end time of day mode are set to 07:00 and 18:00.
Sensitivity
Select Low, Normal, or High sensitivity for the light sensor. at Auto mode.
If switching between Day mode and Night mode is unstable, select Low or Normal.
● When completed with the settings on this page, click Save to enable the settings.
NOTE
79
Preference
On this page, you can tune the White balance, Image adjustment, WDR enhancement and 3D Noise
reduction parameters. You can congure two sets of preferred settings: one for normal situations, the
other for special situations, such as day/night/schedule mode.
White balance: Adjust the value for the best color temperature.
■ Auto: It will automatically adjust the color temperature of the light in response to different light sources.
You may follow the steps below to adjust the white balance to the best color temperature.
1. Set the White balance to Auto.
2. Place a sheet of white paper in front of the lens, then allow the Network Camera to adjust the color
temperature automatically.
3. Click the On button of Fix current value and conrm the setting while the white balance is being
measured.
■ Manual: This item allows users to manually tune the R gain & B gain ratios.
Image Adjustment
■ Brightness: Adjust the image brightness level, which ranges from 0% to 100%.
■
Contrast: Adjust the image contrast level, which ranges from 0% to 100%.
■ Saturation: Adjust the image saturation level, which ranges from 0% to 100%.
■ Sharpness: Adjust the image sharpness level, which ranges from 0% to 100%.
■ Gamma curve: Select the Optimize mode. Or select the Manual mode, and pull the slide bar pointer
to change the preferred level of Gamma correction towards higher contrast or towards the higher
luminance for detailed expression for both dark and lighted areas of an image.
Sensor Setting 1:
For normal situations
Sensor Setting 2:
For special situations
80
■ Enable low light compensation: Select this option in low light mode, and the values of sharpness and
brightness will change automatically as the noise reduction function.
NOTE: Sharpness may be temporarily emphasized as it becomes dark.
WDR enhancement
This function allows users to identify more image details with an extreme
contrast from an object of interest with one shadowed side against a bright background,
e.g., an entrance.
You may select the Enable WDR enhancement check-box, and then adjust the strength (low, medium,
high) to reach the best image quality.
3D noise reduction
■ Enable 3DNR: Check to enable 3DNR in order to reduce noises and ickers in image. Use the pull-
down menu to adjust the reduction strength.
● Applying 3D noise reduction will consume processor resource, maximum frame rate will reduce by half.
● When enabling/disabling 3D noise reduction, a momentary noise may occur in the image.
● 3D Noise Reduction is mostly applied in low-light conditions. On the other hand, when enabled in a
low-light condition with fast moving objects, trails of after-images may occur. You may then select a
lower strength level or disable the function.
● When completed with the settings on this page, click Save to enable the settings.
NOTE
81
If you want to congure another sensor setting for day/night/schedule mode, please click Prole to open
the Prole Settings page as shown below.
Please follow the steps below to setup a prole:
1. Check Enable and apply this prole.
2. Select the applied mode: Day mode, Night mode, or Schedule mode. Please manually enter a range of
time if you choose Schedule mode.
3. Configure the settings in the following columns. Please refer to the previous page for detailed
information.
4. Click Save to enable the settings and click Close to exit the page.
82
Exposure Advanced Mode
On this page, you can set the Exposure measurement window, Exposure level, and Exposure control,
You can configure two sets of Exposure settings: one for normal situations, the other for special
situations, such as day/night/schedule mode.
Measurement Window: This function allows users to set measurement window(s) for low light
compesation.
■ Full view: Calculate the full range of view and offer appropriate
light compesation.
■ Custom: This option allows you to manually add customized windows as inclusive or exclusive regions.
A total of 10 windows can be set. Please refer to the next page for detailed illustration.
Sensor Setting 1:
For normal situations
Sensor Setting 2:
For special situations
83
The inclusive window refers to “weighted window“; the exclusive window refers to “ignored window“. It
adopts the weighted averages method to calculate the value.
■ BLC (Back Light Compensation): This option will automatically add a “weighted region“ in the middle of
the window and give the necessary light compensation.
Exposure control:
■
Exposure level: You can manually set the Exposure level, which ranges from -2.0 to +2.0 (dark to
bright).
■ Flickerless: Under some circumstances when there is a difference between the video capture
frequency and local AC power frequency (50Hz or 60Hz) due to the electronic rolling shutters of CMOS
sensor, the mismatch causes color shifts or ickering images. If the above mismatch occurs, select the
Flickerless check-box, and the range of Exposure time will be limited to a range in order to match the AC
power frequency. See the screen capture below.
You can click and drag the semi-circular pointers on the Exposure time and Gain control slide bars
to specify a range of shutter time and Gain control values within which the camera can automatically
tune to an optimal imaging result. For example, you may prefer a shorter shutter time to better capture
moving objects, while a faster shutter reduces light and needs to be compensated by electrical
brightness gains.
NOTE
* In a setup of Exposure time and Gain control, do not set maximum and minimum value as equal.
Weighted region
Ignored region
X
X
Exclude
Include
84
If you want to congure another sensor setting for day/night/schedule mode, please click Prole to open
the Prole settings page as shown below.
Please follow the steps below to setup a prole:
1. Check Enable and apply this prole.
2. Select the applied mode: Day mode, Night mode, or Schedule mode. Please manually enter a range
of time through which you want the Schedule mode to apply.
3. Configure Exposure control and True WDR settings in the folowing columns. Please refer to the
previous page for detailed information.
4. Click Save to enable the setting and click Close to exit the page.
85
Privacy mask Advanced Mode
Click Privacy Mask to open the settings page. On this page, you can block out certain sensitive zones to
address privacy concerns.
■ To set the privacy mask windows, follow the steps below:
1. Click New to add a new window. A text box will appear allowing you to enter a name for the mask.
2. Use four mouse clicks to mark a square area, which is recommended to be at least twice the size of
the object (height and width) you want to cover.
3. Enter a Window Name and click Save to enable the setting.
4. Check Enable privacy mask to enable this function.
●
Up to 5 privacy mask windows can be congured on the same screen.
● If you want to delete a congured
mask
window, click on the ‘X’ button at the side of window
name and then click on the Save button.
NOTE
86
Pixel Calculator
Click the Start button at the lower screen to create a pixel calculator window. Place your cursor on the
window to move it to an area of your interest, and change the size of window to t the area of interest.
Once they are drawn, the numbers of pixels on the sides of windows will appear. This allows you to
calculate if your current configuration fulfills a requirement, for instance, for recognizing the faces of
persons passing through a location. A facial recognition usually requires around 130 pixels per meter or
higher.
1
2
The pixels thus calculated are listed at
the lower screen on a per-stream basis
depending on the frame size you congure
for each video stream.
87
The Field of View window allows you to select either the Hemispheric View or a 1080P Full HD mode.
The 1080P Full HD mode provides a dewarpped section (1920x1080 pixels) out of the 175 degrees
hemispheric view. The 1080P Full HD mode provides a higher frame rate of up to 30fps. It is as if using
the panoramic camera as a standard xed dome camera with a wide view angle.
In the 1080P Full HD mode, selection of display mode will not be available. Also, changing the FOV
option will erase the motion detection, privacy mask, and preset postions you previously congured.
175°
117°
1080P Full HD
window
Hemispheric
view
Below is a conceptual drawing showing the coverage of the 1080P Full HD mode.
If the FOV 1080P mode is selected, the Local dewarp function will not be available.
NOTE
Audio and Video > Stream
FOV (Field of View)
88
Stream settings Advanced Mode
Local dewarp mode:
You can set up different local dewarp mode from drop down list in stream 1 and stream 2. If you disable
this function, select 1O from the list.
This Network Camera supports multiple streams with frame size ranging from 192 x 192 to 1920 x 1920
pixels.
Please follow the steps below to set up those settings for an individual stream:
1. Select a stream to congure its viewing region.
2. Choose a proper Frame Size from the drop-down list according to the size of monitored device.
3. Select the Maximum frame rate.
To change the frame size, frame rate, and other related settings, click on stream settings for a video
stream to its individual conguration panel.
89
Click the stream item to display the detailed information.
This Network Camera offers real-time H.264, MPEG-4 and MJPEG compression standards (Triple
Codec) for real-time viewing.
If H.264 or MPEG-4 mode is selected, the video is streamed via RTSP protocol. There are several
parameters for you to adjust the video performance:
■ Frame size
You can set up different video resolutions for different viewing devices. For example, set a smaller
frame size and lower bit rate for remote viewing on mobile phones and a larger video size and a higher
bit rate for live viewing on web browsers. Note that a larger frame size takes up more bandwidth.
■ Maximum frame rate
This limits the maximum refresh frame rate per second. Set the frame rate higher for smoothlier video
quality.
Regardless of the power line frequency setting (60Hz or 50Hz), the frame rates are selectable at 1fps,
2fps, 3fps, 5fps, 8fps, 10fps, 12fps, and 15fps. You can also select Customize and manually enter a
value.
90
■ Intra frame period
Determine how often to plant an I frame. The shorter the duration, the more likely you will get better
video quality, but at the cost of higher network bandwidth consumption. Select the intra frame period
from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds.
■ Video quality
• Constant bit rate: A complex scene generally produces a larger file size, meaning that higher
bandwidth will be needed for data transmission. The bandwidth utilization is congurable to match
a selected level, resulting in mutable video quality performance. The bit rates are selectable at
the following rates: 20Kbps, 30Kbps, 40Kbps, 50Kbps, 64Kbps, 128Kbps, 256Kbps, 512Kbps,
768Kbps, 1Mbps, 2Mbps, 3Mbps, 4Mbps, 6Mbps, 8Mbps, 10Mbps, 12Mbps, 14Mbps and 16Mbps.
You can also select Customize and manually enter a value up to 40Mbps.
- Target bit rate: select a bit rate from the pull-down menu. The bit rate ranges from 20kbps to a
maximum of 16Mbps. The bit rate then becomes the Average or Upper bound bit rate number.
The Network Camera will strive to deliver video streams around or within the bit rate limitation you
impose.
- Policy: If Frame Rate Priority is selected, the Network Camera will try to maintain the frame rate
per second performance, while the image quality will sometimes be compromised. If Image quality
priority is selected, the Network Camera might drop some video frames in order to maintain image
quality.
• Fixed quality: On the other hand, if Fixed quality is selected, all frames are transmitted with the
same quality; bandwidth utilization is therefore unpredictable.
- Quality: The video quality can be adjusted to the following settings:
Acceptable, Satisfactory, Good, Very Good, and Excellent. You can also select Customize and
manually enter a value.
- Maximum bit rate: With the guaranteed image quality, you might still want to place a bit
rate limitation to control the size of video streams for bandwidth and storage concerns. The
congurable bit rate starts from 1Mbps to 40Mbps.
The Maximum bit rate setting in the Fixed quality configuration can ensure a reasonable and
limited use of network bandwidth. For example, in low light conditions where a Fixed quality
setting is applied, video packet sizes can tremendously increase when noises are produced with
electrical gain.
You may also manually enter a bit rate number by selecting the Customized option.
91
If JPEG mode is selected, the Network Camera continuously sends JPEG images to the client, producing
a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same
image quality, which in turn comes at the expense of variable bandwidth usage. Because the media
contents are a combination of JPEG images, no audio data is transmitted to the client. There are three
parameters provided in MJPEG mode to control the video performance:
■ Frame size
You can set up different video resolution for different viewing devices. For example, set a smaller
frame size and lower bit rate for remote viewing on mobile phones and a larger video size and a higher
bit rate for live viewing on web browsers. Note that a larger frame size takes up more bandwidth.
■ Maximum frame rate
This limits the maximum refresh frame rate per second. Set the frame rate higher for smoother video
quality.
The frame rates are selectable at 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 12fps and 15fps. You can also
select Customize and manually enter a value. The frame rate will decrease if you select a higher
resolution.
■ Video quality
Refer to the previous page setting an average or upper bound threshold for controlling the bandwidth
consumed for transmitting motion jpegs. The conguration method is identical to that for MPEG4 and
H.264.
►
Video quality and xed quality refers to the compression rate. If you select to enter a Customized value in
the Fixed quality menu, a lower value will produce higher quality.
►
Converting high-quality video may significantly increase the CPU loading, and you may encounter
streaming disconnection or video loss while capturing a complicated scene. In the event of occurance,
we suggest you customize a lower video resolution or reduce the frame rate to obtain smooth video.
NOTE
92
Audio and Video > Audio
Audio Settings
Mute: Select this option to disable audio transmission from the Network Camera to all clients. Note that
if muted, no audio data will be transmitted even if audio transmission is enabled on the Client Settings
page. In that case, the following message is displayed:
Note: When enabling/disabling this function, video streaming will be disconnected, and reconnected after
45 seconds.
Microphone source: Select the microphone internal or external.
Internal microphone input gain: Select the gain of the internal audio input according to ambient
conditions. Adjust the gain from 100% (most sensitive) to 0% (least sensitive).
External microphone input gain: Select the gain of the external audio input according to ambient
conditions. Adjust the gain from 100% (most sensitive) to 0% (least sensitive).
Audio type: Select audio codec AAC or GSM-AMR and the bit rate.
■ AAC provides good sound quality at the cost of higher bandwidth consumption. The bit rates are
selectable from: 16Kbps, 32Kbps, 48Kbps, 64Kbps, 96Kbps, and 128Kbps.
■ G.711 also provides good sound quality and requires about 64Kbps. Select pcmu (μ-Law) or pcma
(A-Law) mode.
■ G.726 is a speech codec standard covering voice transmission at rates of 16, 24, 32, and 40kbit/s.
When completed with the settings on this page, click Save to enable the settings.
93
PTZ > PTZ settings
This window is functional only when you congure a video stream to be using the Local
dewarp function.
Changing the Field of View
In this window, functional items related to the preset positions have been cancelled. This window is now
used for changing the eld of view when the Local dewarp is applied to a video stream.
1. First select a video stream for which the eld of view will take effect. Note that you must manually
select a Local dewarp mode (e.g., 1R or 1P) in Audio and Video > Stream > Stream rst.
94
2. Adjust the shooting area to the desired position using the PTZ keypad on the live screen.
Note that the pan, tilt, zoom speeds only applies in this window. They do not apply to the live view in
Main Page
95
Event > Event settings Advanced Mode
This section explains how to congure the Network Camera to respond to particular situations
(event). A typical application is that when a motion is detected, the Network Camera sends
buffered images to an FTP server or e-mail address as notifications. Click on Help, there is
an illustration shown in the pop-up window explaining that an event can be triggered by many
sources, such as motion detection or external digital input devices. When an event is triggered,
you can specify what type of action that will be performed. You can configure the Network
Camera to send snapshots or videos to your email address or FTP site.
Event
To set an event with recorded video or snapshots, it is necessary to configure the server and media
settings so that the Network Camera will know what action to take (such as which server to send the
media les to) when a trigger is activated. An event is an action initiated by a user-dened trigger source.
In the Event column, click Add to open the event settings window.
96
■ Event name: Enter a name for the event setting.
■ Enable this event: Select this option to enable the event setting.
■ Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher
priority setting will be executed rst.
■ Detect next event after seconds: Enter the duration in seconds to pause motion detection after a
motion is detected. This can prevent event-related actions to be too frequently performed.
Follow the steps 1~3 to arrange the three elements -- Schedule, Trigger, and Action to set an event. A
total of 3 event settings can be congured.
1. Schedule
Specify the period for the event. Please select the days of the week and the time in a day (in 24-hr time
format) to specify when will the event-triggering conditions take effect.
2. Trigger
This is the cause or stimulus which denes what will trigger the event. The trigger source can be cong-
ured to use the Network Camera’s built-in motion detection mechanism or external digital inputs.
There are several choices of trigger sources as shown on next page.
Select each item to display its
related options.
■ Video motion detection
This option makes use of the built-in motion detection mechanism as a trigger source. To enable this
function, you need to congure a Motion Detection Window rst. For more information, please refer to
Motion Detection on page 109 for details.
■ Periodically
This option allows the Network Camera to trigger periodically for every other dened minute. Up to 999
minutes are allowed.
■ Digital input
This option allows the Network Camera to use an external digital input device or sensor as a trigger
source. Depending on your application, there are many choices with digital input devices on the market
which help detect changes in temperature, vibration, sound, light, etc.
■ System boot
This option triggers the Network Camera when the power to the Network Camera is disconnected.
■ Recording notify
This option allows the Network Camera to trigger when the recording disk is full or when recording
starts to overwrite older data.
97
■ Audio detection
A preset threshold can be congured with an external microphone as the trigger to system event. The
triggering condition can be an input exceeding or falling below a threshold. Audio detection can take
place as a complement to motion detection or as a method to detect activities not covered by the
camera's view.
Once you have a preset audio alarm level, you can dene the triggering condition either as an audio input rises above or
falls below the alarm level.
■ Camera tampering detection
This option allows the Network Camera to trigger when the camera detects that is is being tampered
with. To enable this function, you need to congure the Tampering Detection option rst. Please refer
to page 112 for detailed information.
■ Manual Trigger
This option allows users to enable event triggers manually by clicking the on/off button on the
homepage. Please congure 1 to 3 associated events before using this function.
98
■ Extension platform (EP)
It is presumed that you already uploaded and enabled the EP modules before you can
associatee EP triggers with an Event setting.
Click on the Set EP Trigger button to open the EP setup menu. The triggering conditions
available with 3rd-party software modules known as EP will be listed. Use the arrow buttons to
select these triggers. Users may implant these modules for different purposes such as triggering
motion detection, or applications related to video analysis, etc. Please refer to page 115 for the
conguration options with EP modules.
Once the triggers are congured, they will be listed under the EP option.
99
3. Action
Dene the actions to be performed by the Network Camera when a trigger is activated.
■ Trigger digital output for seconds
Select this option to turn on the external digital output device when a trigger is activated. Specify the
length of the trigger interval in the text box.
■ Backup media if the network is disconnected
Select this option to backup media le on SD card if the network is disconnected. This function will only
be displayed after you set up a networked storage device (NAS).
100
Add server
To congure an event with video recording or snapshots, it is necessary to congure/provide servers and
storage media settings so that the Network Camera will know where to send the media les to when a
trigger is activated.
Click Add server to unfold the server setting window. You can specify where the notication messages
are sent when a trigger is activated. A total of 5 server settings can be congured.
There are four choices of server types available: Email, FTP, HTTP, and Network storage.
Select the item
to display the detailed conguration options. You can congure either one or all of them.
Server type - Email
Select to send the media les via email when a trigger is activated.
■ Server name: Enter a name for the server setting.
■ Sender email address: Enter a valid email address as the sender address.
■ Recipient email address: Enter a valid email address as the recipient address.
■ Server address: Enter the domain name or IP address of the email server.
■ User name: Enter the user name of the email account if necessary.
■ Password: Enter the password of the email account if necessary.
■ Server port: The default mail server port is set to 25. You can also manually set another port.
If your SMTP server requires a secure connection (SSL), check This server requires a secure
connection (SSL).
101
To verify if the email settings are correctly congured, click Test. The result will be shown in a pop-up
window. If successful, you will also receive an email indicating the result.
Click Save server to enable the settings, then click Close to exit the Add server page.
After you set up the rst event server, a new item for event server will automatically appear on the Server
list. If you wish to add more server options, click Add server.
Server type - FTP
Select to send the media les to an FTP server when a trigger is activated.
■ Server name: Enter a name for the server setting.
■ Server address: Enter the domain name or IP address of the FTP server.
■ Server port: By default, the FTP server port is set to 21. It can also be assigned to another port number
between 1025 and 65535.
■ User name: Enter the login name of the FTP account.
■ Password: Enter the password of the FTP account.
■ FTP folder name
Enter the folder where the media le will be placed. If the folder name does not exist, the Network
Camera will create one on the FTP server.
102
■ Passive mode
Most firewalls do not accept new connections initiated from external requests. If the FTP server
supports passive mode, select this option to enable passive mode FTP and allow data transmission to
pass through the rewall.
To verify if the FTP settings are correctly congured, click Test. The result will be shown in a pop-up
window as shown below. If successful, you will also receive a test.txt le on the FTP server.
Click Save server to enable the settings, then click Close to exit the Add server page.
Server type - HTTP
Select to send the media les to an HTTP server when a trigger is activated.
■ Server name: Enter a name for the server setting.
■ URL: Enter the URL of the HTTP server.
■ User name: Enter the user name if necessary.
■ Password: Enter the password if necessary.
To verify if the HTTP settings are correctly congured, click Test. The result will be shown in a pop-up
window as below. If successful, you will receive a test.txt le on the HTTP server.
Click Save server to enable the settings and click Close to exit the Add server page.
103
Network storage:
Select to send the media les to a network storage location when a trigger is activated. Please refer to
NAS server on page 119 for details.
Click Save server to enable the settings, then click Close to exit the Add server page.
■ SD Test: Click to test your SD card. The system will display a message indicating success or failure. If
you want to use your SD card for local storage, please format it before use. Please refer to page 122
for detailed information.
■ View: Click this button to open a le list window. This function is only for SD card and Network Storage.
If you click the View button of SD card, a Local storage page will pop up for you to manage recorded
les on SD card. For more information about Local storage, please refer to page 122. If you click the
View button of Network storage, a le directory window will prompt for you to view recorded data on
Network storage.For detailed illustration, please refer to the next page.
■ Create folders by date, time, and hour automatically: If you check this item, the system will generate
folders automatically by the date when video footages are stored onto the networked storage.
The following is an example of a le destination with video clips:
104
Click to delete
selected items
Click to delete all
recorded data
Click to go back to the previous
level of the directory
The format is: HH (24r)
Click to open the le list for that hour
The format is: File name prex + Minute (mm)
You can set up the le name prex on Add media page. Please
refer to next page for detailed information.
2014/08/20
2014/08/20
2014/08/20
2014/08/20
105
Add media
Click Add media to open the media setting window. You can specify the type of media that will be
sent when a trigger is activated. A total of 5 media settings can be congured. There are three choices
of media types available: Snapshot, Video Clip, and System log.
Select the item to display the detailed
conguration options. You can congure either one or all of them.
Media type - Snapshot
Select to send snapshots when a trigger is activated.
■ Media name: Enter a name for the media setting.
■ Source: Select to take snapshots from streams 1 ~ 4.
■ Send pre-event images
The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number
to decide how many images to capture before a trigger is activated. Up to 7 images can be generated.
■ Send post-event images
Enter a number to decide how many images to capture after a trigger is activated. Up to 7 images can
be generated.
For example, if both the Send pre-event images and Send post-event images are set to 7, a total of 15
images are generated after a trigger is activated.
■ File name prex
Enter the text that will be appended to the front of the le name.
1 pic. 2 pic. 3 pic. 4 pic. 5 pic. 6 pic. 7 pic. 8 pic. 9 pic.
10 pic. 11 pic. 10 pic. 12 pic. 13 pic. 14 pic. 15 pic.
Trigger Activation
106
■ Add date and time sufx to the le name
Select this option to add a date/time sufx to the le name.
For example:
Click Save media to enable the settings, then click Close to exit the Add media page.
After you set up the rst media server, a new column for media server will automatically display on the
Media list. If you wish to add more media options, click Add media.
Media type -
Video clip
Select to send video clips when a trigger is activated.
■ Media name: Enter a name for the media setting.
■ Source: Select the source of video clip.
■ Pre-event recording
The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number
to decide the duration of recording before a trigger is activated. Up to 9 seconds of video can be
recorded.
Snapshot_20141015_100341
Date and time suffix
The format is: YYYYMMDD_HHMMSS
File name prefix
107
■ Maximum duration
Specify the maximum recording duration in seconds. Up to 10 seconds of video can be recorded.
For example, if pre-event recording is set to 5 seconds and the maximum duration is set to 10
seconds, the Network Camera continues to record for another 4 seconds after a trigger is activated.
■ Maximum le size
Specify the maximum le size allowed. Set up sufcient size in
consideration of the resolution, frame rate, and Pre/Post time.
If le size is not enough, nothing may be recorded on SD card
when event occurs.
■ File name prex
Enter the text that will be appended to the front of the le name.
For example:
Click Save media to enable the settings, then click Close to exit the Add media page.
Media type - System log
Select to send a system log when a trigger is activated.
Click Save media to enable the settings, then click Close to exit the Add media page.
1 sec. 2 sec. 3 sec. 4 sec. 5 sec. 6 sec. 7 sec. 8 sec. 9 sec. 10 sec.
Trigger Activation
Video_20141015_100341
Date and time suffix
The format is: YYYYMMDD_HHMMSS
File name prefix
108
In the Event settings column, the Servers and Medias you congured will be listed; please make sure the
Event -> Status is indicated as ON, in order to enable the event triggering action.
When completed, click Save event to enable the settings and click Close to exit Event Settings page.
The new Event / Server settings / Media will appear in the event drop-down list on the Event setting
page.
Please see the example of the Event setting page below:
When the Event Status is ON, once an event is triggered by motion detection, the Network Camera will
automatically send snapshots via e-mail.
If you want to stop the event trigger, you can click ON to turn it to OFF status or click Delete to remove
the event setting.
To remove a server setting from the list, select a server name from the drop-down list and click Delete.
Note that you can only delete a server setting when it is not applied to an event setting.
To remove a media setting from the list, select a media name from the drop-down list and click Delete.
Note that you can only delete a media setting when it is not applied to an event setting.
If you Power-OFF or remove the SD memory card from camera, you have to turn
OFF the event status preliminarily.
109
Applications > Motion detection
This section explains how to congure the Network Camera to enable motion detection. A total
of three motion detection windows can be congured.
Follow the steps below to enable motion detection:
1. Click New to add a new motion detection window.
2. In the Window Name text box, enter a name for the motion detection window.
■ Use four mouse clicks to dene the area where Motion Detection will take effect.
■ To change the four points of the rectangular, place your mouse cursor on any of it until it turns into a
four-direction mark.
3. Dene the sensitivity to moving objects and the space ratio of all alerted pixels by moving the
Sensitivity and Percentage slide bar.
4. Click Save to enable the settings.
5. Select Enable motion detection to enable this function.
For example:
The Percentage Indicator will rise or fall depending on the variation between sequential images. When
motions are detected by the Network Camera and are considered to have exceeded the defined
threshold, the red bar rises. Meanwhile, the motion detection window will be outlined in red. Photos or
videos can be captured instantly and congured to be sent to a remote server (Email, FTP) using this
feature as a trigger source. For information on event settings, please refer to Event settings on page 95.
Motion Detection Setting 2:
For special situations
Motion Detection Setting 1:
For normal situations
110
A green bar indicates that even though motions have been detected, the event has not been triggered
because the image variations still fall under the dened threshold.
If you want to congure specic motion detection settings individually for day/night/schedule operations,
please click Prole to open the Motion Detection Prole Settings page as shown below. A total of three
motion detection windows can be congured on this page as well.
Please follow the steps beolw to set up a prole:
1. Create a new motion detection window.
2. Check Enable this prole.
3. Select the applicable mode: Day mode, Night mode, or Schedule mode. Please manually enter a time
range if you prefer the Schedule mode.
4. Click Save to enable the settings and click Close to exit the page.
This motion detection window will also be displayed on the Event settings page. You can go to Event >
Event settings > Trigger to choose it as a trigger source. Please refer to page 96 for detailed information.
Percentage = 30%
111
● How does motion detection work?
There are two motion detection parameters: Sensitivity and Percentage. In the illustration
above, frame A and frame B are two sequential images. Pixel differences between the
two frames are detected and highlighted in gray (frame C) and will be compared with the
sensitivity setting. Sensitivity is a value that expresses the sensitivity to moving objects.
Higher sensitivity settings are expected to detect slight movements while smaller sensitivity
settings will neglect them. When the sensitivity is set to 70%, the Network Camera denes
the pixels in the purple areas as “alerted pixels” (frame D).
Percentage is a value that expresses the proportion of “alerted pixels” to all pixels in the
motion detection window. In this case, 50% of pixels are identied as “alerted pixels”. When
the percentage is set to 30%, the motions are judged to exceed the defined threshold;
therefore, the motion window will be outlined in red.
For applications that require a high level of security management, it is suggested to use
higher sensitivity settings and smaller percentage values.
A
B D
C
NOTE
112
Applications > DI and DO
Connect DI or DO devices to the camera's terminal block, the camera will automatically detect
the current connection state as pulled-high or pulled-low. You may then define the triggering
condition.
Digital input: Select High or Low to dene the "Normal status" for the digital input. The Network
Camera will report the current status.
Digital output: Select Grounded or Open to dene the "Normal status" for the digital output. The
Network Camera will show whether the trigger is activated or not.
Applications > Tampering detection
This section explains how to set up camera tamper detection. With tamper detection, the
camera is capable of detecting incidents such as redirection, blocking or defocusing, or even
spray paint.
Please follow the steps below to set up the camera tamper detection function:
1. Check Enable camera tampering detection.
2. Enter the tamper trigger duration. (10 sec. ~ 10 min.) The tamper alarm will be triggered only
when the tampering factor (the difference between current frame and pre-saved background)
exceeds the trigger threshold.
3. Set up the event source as Camera Tampering Detection on Event > Event settings >
Trigger. Please refer to page 96 for detailed information.
113
Applications > Audio detection
Audio detection, along with video motion detection, is applicable in the following scenarios:
1. Detection of activities not covered by camera view, e.g., a loud input by gun shots or breaking a
door/window.
2. A usually noisy environment, such as a factory, suddenly becomes quiet due to a breakdown of
machines.
3. A PTZ camera can be directed to turn to a preset point by the occurrence of audio events.
4. Dark environments where video motion detection may not function well.
The red circles indicate where the audio alarms can be triggered when breaching or falling below the preset threshold.
How to congure Audio detection:
1. Once the Audio detection window is opened, the current sound input will be interactively
indicated by a uctuating yellow wave diagram.
2. Use a mouse click to drag the Alarm level tab to a preferred location on the slide bar.
3. Select the “Enable audio detection“ checkbox and click Save to enable the feature.
1�Notethatthevolumenumbers(0~100)onthesideofwavediagramdoesnotrepresentdecibel
(dB)�Soundintensitylevelhasalreadybeenmappedtopresetvalues�Youcan,however,use
thereal-worldinputsatyourinstallationsitethatareshownonthewavediagramtocongure
analarmlevel�
2�Tocongurethisfeature,youmustnotmutetheaudioinConguration > Audio and Video >
Audio�
NOTE
114114
• If the Alarm level and the received volume are set within a range of 20% on the wave
diagram, frequent alarms will be triggered. It is recommended to set the Alarm level
farther apart from the detected sound level.
• To configure and enable this feature, you must not configure video stream #1 into
Motion JPEG. If an external microphone input is connected and recording of audio
stream is preferred, audio stream is transmitted between camera and viewer/recording
station along with stream #1.
• Refer to page 92 for Audio settings, and page 88 for video streaming settings.
You can use the Prole window to congure a different Audio detection setting. For example, a
place can be noisy in the day time and become very quiet in the night.
1. Click on the Enable this prole checkbox. Once the Audio detection window is opened, the
current sound input will be interactively indicated by a uctuating yellow wave diagram.
2. Use a mouse click to drag the Alarm level tab to a preferred location on the slide bar.
3. Select the Day, Night, or Schedule mode check circles. You may also manually congure a
period of time during which this prole will take effect.
4. Click Save and then click Close to complete your conguration.
NOTE
115
Applications > Extension Platform
Users can store and execute 3rd-party software modules onto the camera's ash memory
or SD card.
• Once the software package is successfully uploaded, the module configuration
information is displayed. When uploading a module, the camera will examine whether
the module ts the predened Extension platform requirements.
• To enable extended analytics features, go to
http://www.toshibasecurity.com/support/license for more information
116
To start a module, select the checkcircle in front, and click the Start button.
If you should need to remove a module, select the checkcircle in front and then click the
Stop button. By then the module status will become OFF, and the X button will appear at
the end of the row. Click on the X button to remove an existing module.
When prompted by a conrm message, Click Yes to proceed.
Note that the actual memory consumed while operating the module will be indicated on the
Memory status eld. This helps determine whether a running module has consumed too
much of system resources.
117
Recording > Recording settings Advanced Mode
This section explains how to congure the recording settings for the Network Camera.
Recording Settings
Recording Settings
Click Add to open the recording setting window. On this page, you can dene the adaptive recording,
recording source, recording schedule, and recording capacity. A total of 2 recording settings can be
congured.
■ Recording name: Enter a name for the recording setting.
■ Enable this recording: Select this option to enable video recording.
■ With adaptive recording:
Select this option will activate the frame rate control according to alarm trigger. The frame control
means that when there is a triggered alarm/event, the frame rate will raise up to the value you’ve set
on the Stream setting page. Please refer to page 88 for more information.
Insert your SD card and click here to test
● Please remember to format your SD card when used for the rst time. Please refer to page
122 for detailed information.
NOTE
118
If you enable adaptive recording and enable time-shift cache stream on Camera A, only when an event
is triggered on Camera A will the server record the streaming data in full frame rate; otherwise, it will only
request the I frame data during normal monitoring, thus effectively save lots of bandwidths and storage.
■ Pre-event recording and post-event recording
The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number
to decide the duration of recording before and after a trigger is activated.
■ Priority: Select the relative importance of this recording (High, Normal, or Low). Recording with a higher
priority setting will be executed rst.
■ Source: Select a stream for the recording source.
● To enable recording notication please congure Event settings rst. Please refer to page 95.
Please follow steps 1~2 below to set up the recording:
1. Trigger
Select a trigger source.
■ Schedule: The server will start to record files on the local storage (SD Card) or network attached
storage (NAS).
■ Network fail: Since network fail, the server will start to record les onto the local storage (SD card).
Time
Bandwidth
Bandwidth
Activity Adaptive Streaming
for Dynamic Frame Rate Control
I frame ---> Full frame rate ---> I frame
Continuous recording
● To enable adaptive recording, please make sure
you’ve set up the trigger sources such as Motion
Detection, DI Device, Manual Trigger, or Audio
detection
● When there is no alarm trigger:
- JPEG mode: record 1 frame per second.
- H.264 mode: record the I frame only.
- Mpeg4 model:record the I frame only.
● When the Intra frame period has been set to larger
than >1s on Video settings page, the Intra frame
period will be forced into 1s when the adaptive
recording is activated.
NOTE
NOTE
119
2. Destination
You can select the SD card or network storage (NAS) for the recorded video les. If you have congured
a NAS server, see details in the following.
NAS server
Click Add NAS server to open the server setting window and follow the steps below to set up:
1. Fill in the information for the access to the shared networked storage.
For example:
2. Click Test to check the setting. The result will be shown in the pop-up window.
Network storage path
(\\server name or IP address\folder name)
User name and
password for your
server
1
2 4
3
120
If successful, you will receive a test.txt le on the network storage server.
3. Enter a server name.
4. Click Save to complete the settings and click Close to exit the page.
■ Capacity: You can choose either the entire free space available or limit the reserved space. The
recording size limit must be larger than the reserved amount for cyclic recording.
■ File name prex: Enter the text that will be appended to the front of the le name.
■ Enable cyclic recording: If you check this item, when the maximum capacity is reached, the oldest le
will be overwritten by the latest one. The reserved amount is reserved for the transaction stage when
the storage space is about to be full and new data arrives. The minimum for the Reserved space must
be larger than 15 MBytes.
■ Recording file management: You can manually assign the Maximum duration and the Maximum
file size for each recording footage. You may need to stitch individual files together under some
circumstances. You may also designate a le name prex by lling in the responsive text eld.
121
To remove a recording setting from the list, select a recording name from the drop-down list and
click Delete.
■ Click Video (Name): Opens the Recording Settings page to modify.
■ Click ON (Status): The Status will become OFF and stop recording.
■ Click NAS (Destination): Opens the file list of recordings. For more information about folder
naming rules, please refer to page 119 for details.
■ Click SD (Destination): Opens the Content management page of Local storage. For more
information, please refer to page 123 for details.
If you want to enable recording notification, please click
Event
to configure event triggering
settings. Please refer to Event > Event settings on page 95 for more details.
When completed, select Enable this recording. Click Save to enable the setting and click Close
to exit this page. When the system begins recording, it will send the recorded les to the network
storage. The new recording name will appear in the drop-down list on the recording page as shown
below.
If you Power-OFF or remove the SD memory card from camera, you have to turn
OFF the event status preliminarily.
122
Local storage > SD card management
This section explains how to manage the local storage on the Network Camera. Here you can
view SD card status, and implement SD card control.
SD card status
This column shows the status and reserved space of your SD card.
SD card format
Remember to format the SD card when using for the rst time.
■ FAT32 : Standard le system Windows PC supported. Maximum 32GB SD card can be formatted.
■ Ext3 : Standard le system on Linux, Windows PC doesn’t support directly.
SD card control
■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When recording uses up
all capacity, the oldest le will be overwritten by the latest le.
■ Enable automatic disk cleanup: Check this item and enter the number of days you wish to retain a le.
For example, if you enter “7 days”, the recorded les will be stored on the SD card for 7 days.
When all settings are completed, click Save to enable your settings.
Advanced Mode
123
Local storage > Content management
This section explains how to manage the content of recorded videos on the Network Camera. Here you
can search and view the records and view the searched results.
Searching and Viewing the Records
This column allows the user to set up search criteria for recorded data. If you do not select any criteria
and click Search button, all recorded data will be listed in the Search Results cloumn.
■ Trigger type: Select one or more items as your search criteria.
■ Media type : Select one you want to search.
■ Time: Select and enter the time range you want to search.
(Note: If time zone of camera and PC is different, set up camera’s time in here.)
Click Search and the recorded data corresponding to the search criteria will be listed in Search Results
window.
Search Results
The following is an example of search results. There are some columns: Name, Trigger type, Starting
time and Ending time for Video clip. And Trigger type and Trigger time are for Snapshot and Text. Click
to sort the search results in either direction.
Tick-box
Numbers of entries
displayed
on one page
Click to browse
pages
Advanced Mode
■ Play: Click on a search result which will highlight the selected item in blue. Click the
Playback window will open automatically to play back the selected le.
For example:
■ Download: Tick left tick-box to select the items. Then click the Download button and a le download
window will pop up for you to save the le.
■ JPEGs to AVI: This function only applies to “JPEG“ format files such as snapshots. You can select
several snapshots from the list, then click this button. Those snapshots will be converted into an AVI
le.
■ Lock/Unlock: Tick left tick-box to select the items, then click this button. The selected items will become
Locked, which will not be deleted during cyclic recoroding. You can click again to unlock the selections.
■ Remove: Tick left tick-box to select the items. Then click this button to delete the les.
Time line of video clip, and
reload function. If clicked, all
items on search results will
be played back in series.
Full screen, Pause, Playback,
and Select function from the
search results
124
Troubleshooting
Reset and restore
If an operational problem occurred in the camera, please refer to the Reset and Restore
function on page 15.
Audio
When using multiple network cameras, restart Internet Explorer each time you switch
the camera. Using the same Internet Explorer session for the multiple cameras may transmit
multiple camera's audio.
External Microphone
The usable microphone is as follows.
● Plug-in-power Condenser Microphones
● φ3.5mm mini-jack
Recommended system requirements
Windows® 7 Professional
Internet Explorer® Ver 8.0
CPU: Intel® CoreTM i3 or better
Memory: 1GB RAM and more
Recommended IR illuminator coverage
There is a limit in the brightness of IR illuminator, we recommend to install a camera within the
limits of the following.
Plane : 32.81ft (10m) in diameter
Distance : 9.84ft (3m)
Restoring the factory defaults will erase any previous settings.
125
Specications
Power supply 12V DC ± 10 %, PoE(IEEE802.3af), PoE+(IEEE802.3at)
Consumption current 12V DC / 2.1 A,
Image pickup device 1/2.5 inch (4:3), 5Mp CMOS Digital Image Sensor
Maximum resolution Horizontal 1920, Vertical 1920 pixels
Scanning system Progressive
Lens Aperture F=1:2.8
Focal length f= 1.5mm
Angle of view(Typical value) Horizontal 175° Vertical 175°
Day / Night Removable IR-Cut lter in Night mode
IR illuminator 6 IR-LEDs with reector
Minimum object illuminance 0.6 lux at Day mode, 0.01 lux at Night mode (F2.8, LED-
OFF, Gain control 100%, Exposure time 1/30)
0 lux with IR illuminators
Noise Reduction 3D NR
Dynamic range WDR enhancement
White balance AWB (2,500K to 10,000K)
Image size of full view 1920x1920, 1536x1536, 1280x1280, 1056x1056, 768x768,
512x512, 384x384, 256x256, 192x192
Image compression system H.264, MPEG-4, and JPEG
Micro SD Card SD, SDHC, SDXC (Maximum 64GB)
Maximum frame rate at
H.264 and M-JPEG (*1) 15 fps at 1920 x 1920, 30 fps at 1920 x 1080,
Maximum frame rate at
MPEG-4 (*1) 15 fps at 1920 x 1920, 25 fps at 1920 x 1080,
Digital zoom Maximum 12 times
Audio in / Audio out (*2) Built in MIC, MIC IN (plug-in power 3.3V, 200kΩ) / LINE
OUT (1 Vrms)
I/O terminal Input 1, output 1
Network interface 10Base-T / 100Base-TX, RJ45 connector
Protocols IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, RTSP/RTP/
RTCP, IGMP, SMTP, FTP, DHCP, NTP, DNS, DDNS,
PPPoE, CoS, QoS, SNMP, and 802.1X
OS Windows® 7 professional
Browser Internet Explorer® Ver. 8.0
ONVIF Prole-S (test tool v14.12)
Operating temperature(*3) PoE:14°F to 122°F (-10°C to 50°C), PoE+ : -22°F to 122°F
(-30°C to 50°C), 12V DC : -22°F to 122°F (-30°C to 50°C)
Operating humidity ~ 90 %
Weight 794g (1.75 lbs)
Dimensions Ф6.3 x 2.0(H) inches ( Ф160 x 51.2(H)mm) (excluding
protrusion)
IP Code IP66
Vandal resistant IK10 (IEC62262)
Railway standard EN50155
Safety regulation UL 60950-1, CSA C22.2 No. 60950-1
EMC standard FCC Class B, IC Class B
Accessories Screws(x6), Anchors(x3), Power & I/O cable(x1),
Mounting Plate(x1), Gasket(x1), Torx driver(x1), Silica
Gel and tape(x1), Rubber Washer(x1), Alignment
sticker(x2), CD-ROM(x1), Quick Start guide and Important
Safeguards(x1),Warranty Card(x1)
126
●Designsandspecicationsmaychangewithoutpriornoticeforbetterimprovement�
●Screens,photos,illustrationsandotherdiagramscontainedinthisuser'smanualmayslightly
changefromactualones�
*1: Varies in accordance with the object, image quality, network environment and performance
of the personal computer used.
*2: The sound may not be clear depending on the conditions of the lines.
*3: An internal heater is automatically turned on at low temperature, when a power supply is
PoE+ and 12V DC.
127
φ6.3"(160)
1.53"(38.8)
2.02"(51.2)
φ5.67"(144)
26°
8°
8°
8°
26°
8°
φ6.31"(160.35)
φ0.14"(3.45)
0.43"(11)
2.36"(59.97)
φ
5.56"(141.22)
M3X0.5 TH
30°
13°
13°
47°
47°
13°
φ
4.77"(121.23)
φ
6.38"(161.99)
φ
0.17"(4.3)
Appearance Diagram
Dimensions: inch (mm)
128
(Mounting Plate)
Technology License Notice
MPEG-4 AAC Technology
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS
PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT
REGARD TO PC SOFTWARE, YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL
PURPOSES.FOR MORE INFORMATION, PLEASE REFER TO
HTTP://WWW.VIALICENSING.COM.
MPEG-4 Visual Technology
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE
FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING
VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/
OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL
INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND
COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. PLEASE
REFER TO HTTP://WWW.MPEGLA.COM.
AMR-NB Standard
THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE
AGREEMENT. WITH RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING
LICENSORS' PATENTS MAY APPLY:
TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938;
6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION:
AT PAT. 0516621; BE PAT. 0516621; CA PAT. 2010830; CH PAT. 0516621; DE PAT. 0516621;
DK PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621; GB PAT. 0516621; GR PAT. 0516621;
IT PAT. 0516621; LI PAT. 0516621; LU PAT. 0516621; NL PAT. 0516621; SE PAT 0516621; US
PAT 5444816; AT PAT. 819303/AT E 198805T1; AU PAT. 697256; BE PAT. 819303; BR PAT.
9604838-7; CA PAT. 2216315; CH PAT. 819303; CN PAT. ZL96193827.7; DE PAT. 819303/
DE69611607T2; DK PAT. 819303; ES PAT. 819303; EP PAT. 819303; FR PAT. 819303; GB
PAT. 819303; IT PAT. 819303; JP PAT. APP. 8-529817; NL PAT. 819303; SE PAT. 819303; US
PAT. 5664053. THE LIST MAY BE UPDATED FROM TIME TO TIME BY LICENSORS AND A
CURRENT VERSION OF WHICH IS AVAILABLE ON LICENSOR'S WEBSITE AT
HTTP://WWW.VOICEAGE.COM.
About the software
This product contains a piece of software licensed to TOSHIBA CORPORATION (hereafter
TOSHIBA) by a third party. The copyright and other intellectual property rights of the software
are held by this third party or the licensor. The software is protected by the Copyright Law,
Universal Copyright Convention, and other intellectual property laws and agreements. The
permission of Toshiba and the third party must therefore be obtained before the software can be
reproduced. Contact Toshiba if you need it for more information at
http://www.toshibasecurity.com/support.
129
End-user License Agreement on Free Software Components Used in the
TOSHIBA Network Camera
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but
changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change
it. By contrast, the GNU General Public License is intended to guarantee your freedom to share
and change free software--to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation's software and to any other program
whose authors commit to using it. (Some other Free Software Foundation software is covered
by the GNU Lesser General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public
Licenses are designed to make sure that you have the freedom to distribute copies of free
software (and charge for this service if you wish), that you receive source code or can get it if
you want it, that you can change the software or use pieces of it in new free programs; and that
you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these
rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities
for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must
give the recipients all the rights that you have. You must make sure that they, too, receive or can
get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license
which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone
understands that there is no warranty for this free software. If the software is modified by
someone else and passed on, we want its recipients to know that what they have is not the
original, so that any problems introduced by others will not reflect on the original authors'
reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the
danger that redistributors of a free program will individually obtain patent licenses, in effect
making the program proprietary. To prevent this, we have made it clear that any patent must be
licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modication follow.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the
copyright holder saying it may be distributed under the terms of this General Public License.
The "Program", below, refers to any such program or work, and a "work based on the Program"
means either the Program or any derivative work under copyright law: that is to say, a work
containing the Program or a portion of it, either verbatim or with modications and/or translated
into another language. (Hereinafter, translation is included without limitation in the term
"modication".) Each licensee is addressed as "you".
Activities other than copying, distribution and modication are not covered by this License; they
are outside its scope. The act of running the Program is not restricted, and the output from the
Program is covered only if its contents constitute a work based on the Program (independent of
130
having been made by running the Program). Whether that is true depends on what the Program
does.
1. You may copy and distribute verbatim copies of the Program's source code as you receive
it, in any medium, provided that you conspicuously and appropriately publish on each copy an
appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to
this License and to the absence of any warranty; and give any other recipients of the Program a
copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option
offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a
work based on the Program, and copy and distribute such modications or work under the terms
of Section 1 above, provided that you also meet all of these conditions:
a) You must cause the modied les to carry prominent notices stating that you changed the
les and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or
is derived from the Program or any part thereof, to be licensed as a whole at no charge to
all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must
cause it, when started running for such interactive use in the most ordinary way, to print
or display an announcement including an appropriate copyright notice and a notice that
there is no warranty (or else, saying that you provide a warranty) and that users may
redistribute the program under these conditions, and telling the user how to view a copy
of this License. (Exception: if the Program itself is interactive but does not normally print
such an announcement, your work based on the Program is not required to print an
announcement.)
These requirements apply to the modied work as a whole. If identiable sections of that work
are not derived from the Program, and can be reasonably considered independent and separate
works in themselves, then this License, and its terms, do not apply to those sections when you
distribute them as separate works. But when you distribute the same sections as part of a whole
which is a work based on the Program, the distribution of the whole must be on the terms of this
License, whose permissions for other licensees extend to the entire whole, and thus to each and
every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written
entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or
collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or
with a work based on the Program) on a volume of a storage or distribution medium does not
bring the other work under the scope of this License.
3. You may copy an d distribute the Program (or a work based on it, under Section 2) in
object code or executable form under the terms of Sections 1 and 2 above provided that you
also do one of the following:
a) Accompany it with the complete corresponding machine-readable source code, which must
be distributed under the terms of Sections 1 and 2 above on a medium customarily used
for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any third party, for
a charge no more than your cost of physically performing source distribution, a complete
machine-readable copy of the corresponding source code, to be distributed under the
terms of Sections 1 and 2 above on a medium customarily used for software interchange;
or,
131
132
c) Accompany it with the information you received as to the offer to distribute corresponding
source code. (This alternative is allowed only for noncommercial distribution and only if you
received the program in object code or executable form with such an offer, in accord with
Subsection b above.)
The source code for a work means the preferred form of the work for making modications to
it. For an executable work, complete source code means all the source code for all modules
it contains, plus any associated interface definition files, plus the scripts used to control
compilation and installation of the executable. However, as a special exception, the source code
distributed need not include anything that is normally distributed (in either source or binary form)
with the major components (compiler, kernel, and so on) of the operating system on which the
executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated
place, then offering equivalent access to copy the source code from the same place counts as
distribution of the source code, even though third parties are not compelled to copy the source
along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly
provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the
Program is void,and will automatically terminate your rights under this License. However, parties
who have received copies, or rights, from you under this License will not have their licenses
terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing
else grants you permission to modify or distribute the Program or its derivative works. These
actions are prohibited by law if you do not accept this License. Therefore, by modifying or
distributing the Program (or any work based on the Program), you indicate your acceptance of
this License to do so, and all its terms and conditions for copying, distributing or modifying the
Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient
automatically receives a license from the original licensor to copy, distribute or modify the
Program subject to these terms and conditions. You may not impose any further restrictions
on the recipients' exercise of the rights granted herein. You are not responsible for enforcing
compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any
other reason (not limited to patent issues), conditions are imposed on you (whether by court
order, agreement or otherwise) that contradict the conditions of this License, they do not excuse
you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously
your obligations under this License and any other pertinent obligations, then as a consequence
you may not distribute the Program at all. For example, if a patent license would not permit
royalty-free redistribution of the Program by all those who receive copies directly or indirectly
through you, then the only way you could satisfy both it and this License would be to refrain
entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance,
the balance of the section is intended to apply and the section as a whole is intended to apply in
other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right
claims or to contest validity of any such claims; this section has the sole purpose of protecting
the integrity of the free software distribution system, which is implemented by public license
practices. Many people have made generous contributions to the wide range of software
distributed through that system in reliance on consistent application of that system; it is up to the
author/donor to decide if he or she is willing to distribute software through any other system and
133
a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the
rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by
patents or by copyrighted interfaces, the original copyright holder who places the Program under
this License may add an explicit geographical distribution limitation excluding those countries,
so that distribution is permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General
Public License from time to time. Such new versions will be similar in spirit to the present
version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version
number of this License which applies to it and "any later version", you have the option of
following the terms and conditions either of that version or of any later version published by the
Free Software Foundation. If the Program does not specify a version number of this License,
you may choose any version ever published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution
conditions are different, write to the author to ask for permission. For software which is
copyrighted by the Free Software Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will be guided by the two goals of preserving
the free status of all derivatives of our free software and of promoting the sharing and reuse of
software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR
OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH
YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN
WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public,
the best way to achieve this is to make it free software which everyone can redistribute and
change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of
each source le to most effectively convey the exclusion of warranty; and each le should have
at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the
GNU General Public License as published by the Free Software Foundation; either version 2
of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY;
without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE. See the GNU General Public License for more details.
You should have received a copy of the GNU General Public License along with this program;
if not, write to the Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive
mode:
Gnomovision version 69, Copyright (C) year name of author
Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type `show w'.
This is free software, and you are welcome to redistribute it under certain conditions; type
`show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the
General Public License. Of course, the commands you use may be called something other than
`show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your
program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign
a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program `Gnomovision' (which
makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary
programs. If your program is a subroutine library, you may consider it more useful to permit
linking proprietary applications with the library. If this is what you want to do, use the GNU
Lesser General Public License instead of this License.
134
Trademarks
● Microsoft, Windows and Interner Explorer are trademarks or registered trademarks of
Microsoft Corporation in the United States and other countries.
● Intel and Intel Core are trademarks or registered trademarks of Intel Corporation or its
subsidiares in the United States and other countries.
● Adobe and Reader are either registered trademarks or trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
● "ONVIF" and are trademarks of ONVIF Inc.
● Other product names appearing in this manual may be trademarks or registered trademarks of
their respective holders.
135
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
Surveillance & IP Video Products
9740 Irvine Boulevard,
Irvine, CA 92618-1697
Phone Number: (877) 855-1349