Table of Contents
- Table of Contents
- Introduction
- Getting Started
- Locate Camera
- Live
- Setup
- Advanced
- Logout
- Specifications
Toshiba IKS-WR7022 User Manual
Displayed below is the user manual for IKS-WR7022 by Toshiba which is a product in the Security Cameras category. This manual has pages.
Related Manuals
NETWORK CAMERA
Model: IKS-WR7022
User’s Manual
If the URL changes, refer to www.toshiba.com
For information on our latest products and peripheral devices, refer to the
following web site:
www.toshibasecurity.com
32953AC 3
4
Outdoor Repositionable IP Dome Camera (IKS-WR7022)
User Manual
Manual Edition 32953AC – June 2016
©2015, TOSHIBA
All Rights Reserved.
No part of this documentation may be reproduced in any means, electronic or mechanical, for any
purpose, except as expressed in the Software License Agreement. Toshiba shall not be liable for
technical or editorial errors or omissions contained herein. The information in this document is
subject to change without notice.
The information in this publication is provided “as is” without warranty of any kind. The entire risk
arising out of the use of this information remains with recipient. In no event shall TOSHIBA be liable
for any direct, consequential, incidental, special, punitive, or other damages whatsoever (including
without limitation, damages for loss of business profits, business interruption or loss of business
informati on), ev en if TOSHIBA has been advised of the possibility of such damages and whether in
an action or contract or tort, including negligence.
This documentation is copyrighted. All other rights are reserved to TOSHIBA. TOSHIBA, and
Surveillix, are registered trademarks of TOSHIBA in the United States and elsewhere; Windows,
and Windows XP Embedded are registered trademarks of Microsoft Corporation. All other brand
and product names are trademarks or registered trademarks of the respective owners.
TOSHIBA
Irvine, CA ● U.S.A.
32953AC 5
Important Safeguards
1. Read Instructions
Read all the safety and operating instructions before operating the product.
2. Retain Instructions
Retain the safety instructions and user's manual for future reference.
3. Warnings
Comply with all warnings on the product and in the user's manual.
4. Follow Instructions
Follow all operating and use instructions.
5. Cleaning
Disconnect this camera from the power supply before cleaning.
6. Attachments
Do not use attachments not recommended by the camera manufacturer as they may pose
safety risks.
7. Water and Moisture
Do not use this camera near water. Some examples are: near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.
8. Accessories
Do not place this camera on an unstable cart, stand, tripod, bracket or table. The camera
may fall, causing serious injury to a person, or serious damage to the product. Use
only withstand, tripod, bracket, or table recommended by the manufacturer, or sold
with the camera. Any mounting of the product should follow the manufacturer's
instructions, and should use amounting accessory recommended by the
manufacturer.
9. Ventilation
This camera should never be placed near or over a radiator or heat register. If this product
is placed in a built-in installation, verify that there is proper ventilation so that the
camera temperature operates within the recommended temperature range.
10. Power Sources
This camera should be operated only from the type of power source indicated on the
information label. If you are not sure of the type of power supply at your location,
consult your product dealer.
11. Power-Cord Protection
Power cords should be routed so that they are not likely to be walked on or pinched by
items placed upon or against them. Pay particular attention to cords at plugs, screws
and the point where they exit the product.
12. Installation
Install this camera on a secure part of the ceiling or wall. If installed on an unsecured
location the camera could fall causing injury and damage.
6
13. Lightning
For additional protection on this camera during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the power supply and cable system. This will prevent damage to the
camera due to lightning and power line surges. If lightning occurs, do not touch the
unit or any connected cables in order to avoid electric shock.
14. Overloading
Do not overload the power supply or extension cords as this can result in a risk of fire or
electric shock.
15. Object and Liquid Entry
Never push objects of any kind into this camera through openings as they may touch
dangerous electrical points or short-out parts that could result in a fire or electrical
shock. Never intentionally spill liquid of any kind on the camera.
16. Servicing
Do not attempt to service this camera yourself as opening or removing covers may expose
you to dangerous electrical or other hazards. Refer all servicing to qualified service
personnel.
17. Damage Requiring Service
Disconnect this camera from the power supply and refer servicing to qualified service
personnel under the following conditions.
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the camera.
c. If the camera has been submerged in water.
d. If the camera does not operate normally by following the operating instructions in
the user's manual. Adjust only those controls that are covered by the user's manual
as an improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the camera to its normal
operation.
e. If the camera has been dropped or the cabinet has been damaged.
f. When the camera exhibiting a distinct change in performance which indicates a
need for service.
g. Other trouble.
18. Replacement Parts
When replacing parts, be sure the service technician uses parts specified by the
manufacturer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
19. Safety Check
Upon completion of any service or repairs to this camera, ask the service technician to
perform safety checks to determine that the camera is in proper operating condition.
32953AC 7
Precautions
Operating
• Before using, make sure power supply and others are properly connected.
• While operating, if any abnormal condition or malfunction is observed, stop using the
camera immediately and then contact your local dealer.
Handling
• Do not disassem ble or tamper with parts inside the ca mera.
• Do not drop or subject the camera to shock and vibration as this can damage camera.
• Care must be taken when you clean the clear dome cover. Scratches and dust will
ruin the image quality of your camera. Do not use strong or abrasive detergents when
cleaning the camera body. Use a dry cloth to clean the camera when it is dirty. In
case the dirt is hard to remove, use a mild detergent and wipe the camera gently.
Installation and Stora ge
• Do not install the camera in areas of extreme temperatures in excess of the allowable
range. (14°F~ 122°F / -10°C ~ 50°C)
• Avoid installing in humid or dusty places. The relative humidity must be below 90%.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic fields and electric signals.
• Avoid installing in places where the camera would be subject to strong vibrations.
• Never face the camera toward the sun. Do not aim at bright objects. Whether the
camera is in use or not, never aim it at the sun or other extremely bright objects.
Otherwise the camera may be sme ared and dam age d.
Should you notice any trouble
• If any trouble occurs while you are using the camera, turn off the power and contact
your dealer. If you continue to use the camera when there is something wrong with it,
the trouble may get worse and an unpredictable problem may occur.
Disclaimer
• We disclaim any responsibility and shall be held harmless for any damages or losses
incurred by the user in any of the following cases:
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user,
whether intentional or accidental; use under extreme operating conditions.
2. Malfunction or non-functi on resul ting in indirec t , addit ion al or consequen t ia l
damages, including but not limited to loss of expected income and suspension of
business activities.
3. Incorrect use not in compliance with instructions in this user's manual.
4. Malfunctions resulting from misconnection to other equipment.
5. Repairs or modifications made by the user or caused to be made by the user and
carried out by an unauthorized third party.
8
• Notw ithstand ing the f oreg oin g, Toshiba's liabi lities shall not, i n any circumst ances,
exceed the purchase price of the product.
Copyright and Right of Portrait
• There may be a conflict with the Copyright Law and other laws when a customer
uses, displays, distributes, or exhibits an image picked up by the camera without
permission from the copyright holder. Please also note that transfer of an image or file
covered by copyright is restricted to use within the scope permitted by the Copyright
Law.
Protection of Personal Information
• Images taken by the camera that reveal the likeness of an individual person may be
considered personal information. To disclose, exhibit or transmit those images over
the internet or otherw ise, cons ent of the person may be required.
Usage Limitation
• The product is not designed for any "critical applications." "Critical applications"
means life support systems, exhaust or smoke extraction applications, medical
application s, com mer cial aviation, mass transit applications, military applications,
homeland security applications, nuclear facilities or systems or any other applications
where product failure could lead to injury to persons or loss of life or catastrophic
property damage.
• Accordingly, Toshiba disclaims any and all liability arising out of the use of the
product in any critical applications
Regulation
FCC (USA) Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may
cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
32953AC 9
CAUTION: Your authority to operate this FCC verified equipment could be voided if you
make changes or modifications not expressly approved by the party.
Industry Canada Information
CAN ICES-3 A / NMB-3 A
This symbol on the product or on its packaging indicates that this product
shall not be treated as household waste in accordance with Directive
2002/96/EC. Instead it shall behanded over to the applicable collection
point for the recycl ing of electrical and ele ctron ic equ ipm ent. By proper
waste handling of this product you ensure that it has no negative
consequenc es for the env ir on ment and hu man heal th, w hich could
otherwise be caused if this product is thrown into the garbage bin. The
recycling of materials will help to conserve natural resources.
For more details infor mat ion about recycl ing of this prod uct, please cont act
your local city office, your household waste disposal service or the shop
where you purchased the product.
Compliance is evidenced by written declaration from our suppliers, assuring
that any potential trace contamination levels of restricted substances are
below the max imum level set by EU Directive 2002 /95/ EC, o r are exempte d
due to their application.
10
Warning
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE.
DO NOT OPEN THE CABINE T.
THIS INSTALLATION SHOULD BE MADE B Y A QUALIFIED SERVICE PERSON AND
SHOULD CONFORM TO ALL LOCAL CODES.
REFER SERVICING TO QUALIFIED PERSONNEL ONL Y.
Caution
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT RE MO VE COVER (OR BAC K).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SER VIC IN G TO Q UALIF IED SER VI CE PERSON NE L.
CAUTION
RISK OF ELECT RIC SHOCK
DO NOT OPEN
32953AC 11
TABLE OF CONT ENTS
Table of Contents ................................................................................... 11
Introduction ............................................................................................ 14
Overview ....................................................................................................................... 14
Product Features ...................................................................................................... 14
Getting Started ....................................................................................... 15
Box Contents ................................................................................................................ 15
Camera Overview ......................................................................................................... 16
Camera Dimensions ................................................................................................. 16
IKS-WR7022 ........................................................................................................ 16
Connections .............................................................................................................. 17
Indoor Cameras ................................................................................................... 17
POE Power Source .......................................................................................... 17
12vDC Power Source ...................................................................................... 18
Locate Camera ....................................................................................... 19
Device search Software ................................................................................................ 19
Installation ................................................................................................................. 19
Starting De vice Se ar ch ............................................................................................. 19
Device Addressing .................................................................................................... 20
Finding Network Devices ..................................................................................... 20
Viewing a Network Camera.................................................................................. 21
Setup & Configuration ................................................................................................... 22
Connectin g to the Camera ........................................................................................ 22
Resetting the Camera .......................................................................................... 22
Administr ator /Us er Pr i vileg es ............................................................................... 22
Connecting Over the Internet ............................................................................... 23
Viewer Software ............................................................................................................ 23
Viewer Tabs .............................................................................................................. 24
Live .......................................................................................................... 25
Setup ....................................................................................................... 26
System Setting .............................................................................................................. 26
Camera Name .......................................................................................................... 26
IP Address ................................................................................................................ 26
12
Get IP an Address Automatically (DHCP) ............................................................ 27
Use Static IP Address .......................................................................................... 27
IPv6 Address Configuration ............................................................................. 28
User Setup ................................................................................................................ 28
Admin Password .................................................................................................. 28
Add User .............................................................................................................. 28
Delete User .......................................................................................................... 28
Modify User .......................................................................................................... 29
File Locatio n ............................................................................................................. 29
Picture Setup ................................................................................................................ 29
Camera Tab .............................................................................................................. 29
Exposure .............................................................................................................. 29
White Balance ...................................................................................................... 30
Picture Adjustment ............................................................................................... 31
Motion Detection ....................................................................................................... 31
Add Detection Window ......................................................................................... 32
Delete Motion Detection Window ......................................................................... 32
Motion Window ................................................................................................ 32
Stream ing Sett ings ....................................................................................................... 33
Video Resolution ...................................................................................................... 33
Video Orientation ................................................................................................. 34
GOP Size ............................................................................................................. 34
H.264 Profile ........................................................................................................ 34
Video Frame Rate .................................................................................................... 35
Video Compression .................................................................................................. 36
Advanced ................................................................................................ 37
System Setting .............................................................................................................. 37
Network Setup .......................................................................................................... 37
DDNS ................................................................................................................... 37
Network Advanced ................................................................................................... 37
QoS ...................................................................................................................... 37
SNMP Settings ..................................................................................................... 38
UPnP (Universal Plug N’ Play) ............................................................................. 38
Network Security ...................................................................................................... 39
HTTP .................................................................................................................... 39
IP Filtering ............................................................................................................ 39
IEEE 802.1XSEAP-TLS ....................................................................................... 39
Alarm Application ...................................................................................................... 40
32953AC 13
Tampering and Network Failure Detection ............................................................... 41
Mail, HTTP and FTP Setup ...................................................................................... 42
SD Card .................................................................................................................... 42
Network Share .......................................................................................................... 43
Recordi ng Sched ul e ................................................................................................. 44
Recording ............................................................................................................. 44
Schedule .............................................................................................................. 45
Interval Recor d ing ................................................................................................ 46
Maintenance ............................................................................................................. 47
Configuration ........................................................................................................ 47
Factory Default ..................................................................................................... 47
Software .................................................................................................................... 48
Picture Setting .............................................................................................................. 48
Video Mask ............................................................................................................... 48
Hot Spot .................................................................................................................... 48
Text Overlay ............................................................................................................. 48
Stream ing Sett ing ......................................................................................................... 49
Audio ......................................................................................................................... 49
Logout ..................................................................................................... 49
Specifications ......................................................................................... 50
Camera Specifications .................................................................................................. 50
32953AA
INTRODUCTION
OVERVIEW
The Toshiba Outdoor Fixed IP cameras are capable of providing real time streaming video
with smooth image quality. The IP Mini Dome cameras offer quad streami ng a nd can be
used in a variety of installations including shops, stores, banks, parking lots, factories and
for building surv eil lan ce.
With Power over Ethernet (PoE) the need for separate power lines is eliminated and
cabling and instal lat ion co sts c an be signif icantly reduced. The light weight, small s ize,
and large degree of rotation of the IP Mini Dome facilitates quick and simple installation on
either the ceiling or walls of structures or vehicles.
Product Fe a t ures
Motorized Repositionable For Easy Adjustment
ONVIF Compliant, Profile S
1080p (2MP) Resolution
30 IPS at all resolutions
1/2.8” COMS Sensor
Digital Day / Night
True Wide Dynamic Range
3D-DNR (3D Digital Noise Reduction)
Motion Detection
1 Sensor Input, 1 Sensor Output
Micro SD/SDHC Card Slot (Card Not Included)
Power Over Ethernet(PoE) & DC12V
32953AC 15
GETTING STARTED
BOX CONTENTS
Before proceedi ng, ple ase check that the box contains the items listed here. If any item is
missing or has defects, DO NOT install or operate the product and contact your dealer for
assistance.
Camera (FPW or AP W) Mount Plate & Torx Tool
Screws & Plastic Anchors x 3 Mount Bolt & Nut x 2
Bolt & Nut Template Sheet Mount Plate Template Sheet
Software CD / Documents
16
CAMERA OVERVIEW
Before installing or connecting the dome camera, please refer to this section and complete
preparations for dome setup and all switch settings.
Camera Dimensions
IKS-WR7022
Width: 4.9”
Height:
2.9”
32953AC 17
Connections
Indoor Cameras
The camera is compatible with 12vDC and Power over Ethernet (PoE). Connect power to
the camera using the provided power connector lead or connect the camera to a PoE
power source. If you are connecting 12vDC power, verify the polarity of the power
connection. If you are using PoE, make sure the Power Sourcing Equipment (PSE) is in
use in the network.
Check the status of the network connection by looking at the link indicator and activity
indicator LEDs. If the LEDs are not lit check your network connection. The green link LED
indicates a network connection and the orange activity LED flashes to indicate network
activity.
POE Power Source
PoE allows for the transmission of power and data via a single Ethernet cable. PoE
eliminates the need for multiple cables to support power and recording. Follow the
installation below to connect the camera to a PoE-enabled switch using an Ethernet cable.
18
12vDC Power Source
If PoE is not being used, a power adapter is needed to power the camera. An additional
12vDC connector cable is required.
32953AC 19
LOCATE CAMERA
DEVICE SEARCH SOFTWARE
Use the included Device Search software to easily find your network cameras for initial
setup. The Surveillix Device Search software can be downloaded from
toshibasecurity.com.
Installation
You can run Device Search on any personal computer (PC) or laptop using the software
CD included with your Surveillix IP camera or by downloading the program from
toshibasecurity.com.
Note Device Search will only work on PCs or laptops that use a Windows operating
system. It is compatible with Windows XP, Vista, 7, and 8.
Starting Device Search
After i nstalling the program on your PC or laptop, open the program to begin configuring
your cameras.
To access Device Search on a Toshiba recorder, you must operate the recorder in
Windows Mode.
1. In the Live Screen, click Exit.
2. Click Restart in Windows Mode.
3. Click OK.
4. Double-click Device Search.
20
Device Addressing
The functions on the Device Addressing tab allow you to find network cameras.
Finding Network De vices
5. Click Device Search.
6. To sort your search by Camera Model, Project, or Camera Name, sele ct your
desired criteria from the appro priate lists.
32953AC 21
Viewing a Network Camera
1. To view a network camera over the web using the camera’s viewer software,
double-click the name of the camera.
2. Click Browse.
3. Enter the Username and Password for the camera. The username and
password are case sensitive. It is strongly recommended that the password be
changed after the initial setup to prevent unauthorized access. The default
username and password for Toshiba IP cameras are as follows.
Username – Admin
Password – 1234
4. The viewer software is now opened in Internet Explorer.
Note The viewer software will install automatically the first time you connect to the
camera. If your internet browser does not install the viewer software, check the
security settings or ActiveX controls and plug-in settings. If your internet browser
asks for permission to install the ActiveX control, you must allow the ActiveX
control to continue the installation. If you are prompted to allow an add-on, cl ic k
Allow.
5. You can now configure your camera using the Viewer Software. For more
information on using Viewer software, please see the user manual for your
camera.
22
SETUP & CONFIGURATION
Connecti ng t o t he Ca m e ra
1. Locate the camera on the IP Finder list.
1. Double-click the camera to open the Viewer software in your web browser.
2. Click Browse in the pop-up window.
3. Log in to the camera with the appropriate User Name and Password.
Note The default User name is admin and the default Password is1234. The
username and password are case sensitive.
Resetting the Camera
If it is necessary to reset the camera to the factory default settings, hold down the Reset
button (see Camera Overview) for 30 seconds. This will return all settings, including
network setup, to the factory default.
Admin ist rat o r/U ser Privileg es
The Administrator account has the authority to configure the IP camera and authorize
users’ access to the camera. The User accounts have access to the camera with limited
authority.
32953AC 23
Connecting Over the Internet
There are some challenges with connecting to Toshiba IP cameras over WAN (internet)
connections because the camera streams video over RTSP. RTSP is an excellent
protocol for media and is now used on many IP cameras (including Toshiba) as the default
streaming option.
RTSP, however, is not suitable for transmission between two locations that are behind
different routers. In this case, the client (f or example, the Toshiba HVR or NVR server
software) connects to the camera, and then requests a stream. The camera uses that
connection to return a stream, but since the connection originated on the client side and
has now switched to the camera (remote) side, the router does not have any way to
determine where the traffic should be routed, so no video appears at the recorder. There
are three solutions to this.
1. Connect modems on both sides directly to the recorder and camera. If there is no
router, no network address translation is needed.
2. Use routers with VPN support and set up a small VPN. Once this is done, the
traffic will be treated as though it were all on the local network.
3. (Best solution) – Use router s w it h connection tracking. This is quite easy;
VOIP also uses RTSP and faces the same challenges. If a router is marketed as
having “VOIP Support”, it will have the necessary connection tracking capability
to allow any type of RTSP communication (not just VOIP).
With proper planning and the correct equipment, RTSP cameras CAN stream over the
WAN to a recording device for minimal additional cost and labor.
Please contact Toshiba support if you require any additional information on these topics.
VIEWER SOFTWARE
To access the setup menu, you need to install the viewer software on your PC or recorder.
The viewer software will install automatically the first time you connect to the camera. If
your internet browser doesn’t install the viewer software, check the security settings or
ActiveX controls and plu g-in settings. If your internet browser asks for permission to install
the ActiveX control, you must allow the ActiveX control to continue the installation.
The first time you connect to a camera, the browser will ask for permission to install the
ActiveX Control necessary to display the camera video. Right-click the information bar and
click Install ActiveX Control to allow the installation.
Note IP camera audio is only available on the Indoor IP mini dome camera. The Talk
button will not be available on the Outdoor version of the camera.
24
View er Tabs
Live – Monitor video and perform other video related functions.
Setup – Set the camera name, IP address, and define users. This tab also allows you to
configure the camera settings and view streams.
Advanced – Perform advanced setup configurations, like network setup, security, alarms
and maintenanc e.
Logout – Change user.
32953AC 25
LIVE
Full Screen – This will display the live feed in full screen.
Snapshot – Click the button, and a JPEG snapshot will automatically be saved in the
appointed place. The default location is: C:\.
Note If you are using Windows Vista or 7, you will need to change the Snapshot
location. Windows UAC does not allow internet programs to write directly to C:\
for security reasons.
Record – Click Record to star recording live video. Click Record again to stop recording
video. Recorded video will be saved automatically to the designated location on the local
workstation. The default location is C:/. This location can be changed in File Location, in
the System menu.
Note If you are using Windows Vista or 7, you will need to change the video clip
location. Windows UAC does not allow internet programs to write directly to C:\
for security reasons.
Microphone – PC Network Camera Manager Software audio to camera, enables audio
through an audio out on the camera.
Live Audio – Camera to PC Network Camera Manager Software, enables audio if a
microphone is equi ppe d to the camera.
Note The Microphone and Live Audio functions are only available on enable cameras.
If the camera is not enabled for these features, an error message will display.
26
SETUP
The Setup menu includes System Settings, Picture Setup, and Streaming Settings.
Note The Setup menu displays limited setup options. For a complete list of setup
options, see the Advanced section.
SYSTEM SETTING
Camera Name
Host Name – The Host Name is used to identify
the camera on your system. If camera based
Motion Detection is enabled and is set to send
alarm message by Mail/FTP, the host name
entered here will display in the alarm message.
Time Zone – Select your time zone.
Time Format – Select your desired time format.
Sync With Computer Time – Select to
synchronize the camera date and time with the
connected recorder.
Sync with NTP Server – Manual allows you to
define the date and time manually. Network Time
Protocol (NTP) is an alternate way to synchronize
your camera’s clock with a NTP server. Specify the
server you wish to synchronize in the NTP Server
box. Then select an Update Interval. For more
information about NTP, visit www.ntp.org.
IP Address
You can choose to use a fixed IP address or a
dynamic IP address (assigned by a DHCP server
or router) for the camera.
32953AC 27
Get IP an Address Automatically (DHCP)
The camera comes preconfigured with a fixed IP address, selecting Get IP address
automatically requires a router or DHCP server to assign an IP address to the camera.
Note Every network device has a unique Media Access Control (MAC) address that
can be used for identification. The MAC address is located on the bottom of
each camera, and on the box label (Toshiba Network Camera Manager also
displays the MAC address for identification). Record your camera’s MAC
address for identification in the future.
Use Static IP Address
To set up a new static IP address:
1. Select the Use stat ic IP address option.
2. Type a new IP address in the IP address box.
3. Type a new address in the Default Gateway box.
4. Click Apply to confirm the new setting.
When using static IP addr es s to log in to the IP Camera, you can access it either through
Toshiba IP Finder software or type the IP address directly in the address bar of your
Internet Explorer.
• IP Address – The IP Address is necessary for network identification.
• Subnet mask – Used to determine if the destination is in the same subnet. The
default value is 255.255.255.0.
• Default gateway – Used to forward frames to destinations on different subnets
or for internet access.
• Primary DNS – The primary domain name server that translates hostnames into
IP addresses.
• Secondary DNS – A secondary domain name server that backups the primary
DNS.
• Web Server port – Defines the port that Internet Explorer uses to connect over
the web and view video. If this port is changed then the new port must be defined
when attempting to web connect (ex: if your camera’s IP address is
192.168.0.100 and you change the web port to 8001, then you must type
http://192.168.0.100:8001 in your browser).
• RTSP port – The default RTSP port is 554; setting range: 1024 ~65535.
• MJPEG over HTTP port – The default HTTP Port is 8008; setting range: 1024
~65535.
• HTTPS port – The default HTTPS Port is 443; setting range: 1024 ~65535.
Note No port number can be used in duplication on more than one item.
28
IPv6 Address Configurati on
To enable IPv6 select Enable IPv6 and click Save. See your network administrator if you
are unsure of your network configuration.
User S etup
Admin Password
Manage the password for the Administr ator accoun t .
To change the administrator password:
1. Type a new Administrator Password, and then type again to confirm the
password.
2. Click Save.
Add User
The user name and passwords are limited to 16 characte rs with no spaces permitted.
There is a maximum of tw enty user accoun ts.
1. Type the new Username and Password.
2. Select I/O Access, Camera Control, Talk, and/or Listen as permissions for the
User.
I/O Access – All functions in the Setup and Advanced menus are available to the
User.
Camera Co ntrol– Allows the User to change camera controls in the Setup
menu.
Talk – Allow the user to speak through the camera microphone.
Listen – Allow the user to listen to audio captured by the camera.
3. Click Add.
Delete User
1. Select the user name on the User Name list.
2. Click Delete to remove the user.
3. Click OK in the confirmation window.
There is a momentary wait time while the Network Camera Manager saves parameters.
When this period is complete, the User will be deleted.
32953AC 29
Modify User
1. Select the user name on the User Name list.
2. Click Edit.
3. In the resulting window, modify the Password and/or feature permissions.
4. Click Save.
Note For security reasons, every time the user properties are opened the access
check boxes are automatically cleared. Make sure you select any user access
options each time you edit the user properties.
File Loca t ion
This is the destination location that snapshot photos and recorded videos will be saved to.
To select a destination location:
1. Click Select.
2. Choose a location or folder.
3. Click Save in the file window, and then click Save again.
PICTURE SETUP
Camera Tab
Use the Camera Tab section to modify picture settings for the camera. The sample image
will change as you modify the picture settings.
Note These settings can drastically affect the camera image. Toshiba suggests that
these settings are only modified by a CCTV professional, or at the instruction or
a technical support representative.
Exposure
30
Min Shutter Speed – Choos e a pre-determined shutter speed.
Manual Mode – Changing the shutter mode to manual will allow you to select the
minimum shutter speed that the camera will use. This can drastically change the amount
of light entering the camera.
Click Set to save your changes.
White Balance
Use the white balance setting to change color representation in difficult lighting conditions.
Auto – White balance works within its color temperature range and calculates the best-fit
white balance.
ATW – Auto-tracing white balance, the camera removes the signals within a range of
2000K to 10000K, which helps to even out the bright white portions of an image.
One Push – Balances color temperature based on a white object within the viewing area.
Manual – Change the white balance value by specifying the R grain and B grain.
Click Set to save your chan ges.
32953AC 31
Picture Adjustment
Each of the Picture Adjustment settings is set to the recommended default.
Brightness – Adjust the image’s brightness on the camera. The Backlight value
is adjustable from 0 (dim) ~ +20 (brightest).
Sharpness – Increasing the sharpness level can make the image looked
sharper; it especially enhances an object’s edge. The value of sharpness is
adjustable from 0 ~ +10 (sharpest).
Contrast– Adjust the contrast value from -6 to 19.
Saturation– Adjust the color saturation form -6 to 19 (most saturation).
Hue– Adjust the hue from -12 to 13.
Backlight– Backlight compensation can correct for overly-bright backli t
scenaries.
D-WDR Function– Turn the Digital Wide Dynamic Range Off, or adjust between
1 and 3.
Click Set after making changes to the Picture Adjustment settings to save the settings and
update the Live screen.
Moti on De t ect ion
Use the Motion Detection menu to configure the motion detection window(s). Here, Motion
Detection can be turned On or Off, and other general setti ngs can be specified.
To enable motion detection:
1. Use the Motion Detection dropdown to
select a motion detection preset (1-4). If
choosing an additional preset after 1, check
the On checkbox.
Note A motion detection preset can be turned
Off at a later time.
2. If desired, check the By Schedule check
box and use the dropdown menu to select a
schedule.
3. Designate the Motion Detection Setting
values.
4. Check the appropriate boxes to designate the Trigger Action.
5. Click Save.
32
Add Detection Window
1. Use the Motion Detection dropdown to select a motion detection preset.
2. Click Add.
Note The selected motion detection square will be red.
3. Arrange and size the moti on detection window as desired .
4. Click Save.
Delete Motion Dete ction Window
1. Click to select the desir ed motion detection window.
2. Click Delete.
Motion Window
The motion window displays a red line and a
dynamic blue line. The red line represents the
Detection Lev el. The blue line will also be present if
motion is present in the camera frame. The blue line
will react accordingly based on the motion in the
camera frame.
32953AC 33
STREAMING SETTINGS
Video Re s olution
The camera provides eight codec opti ons under
video resolution (two single streaming options, two
sets of dual streaming options, two sets of tri-
streaming options, and two sets of quad-streaming
options):
• H.264 Only
• MJPEG Only
• H.264 + H.264
• H.264 + MJPEG
• H.264 + H.264 + H.264
• H.264 + H.264 + MJPEG
• H.264 + H.264 + H.264 + H.264
• H.264 + H.264 + H.264 + MJPEG
Once a codec option is selected, multiple resolutions are available for each stream.
Note Due to resource management, some resolutions may be unavailable when
selecting a dual stream option.
34
Video Orientation
Normal Video – The video will be oriented as the camera position dictates.
180 Degree Rotate – Rotate the video 180 degrees.
90 Degree Clockwise – Rotate the video 90 degrees clockwise.
90 Degree Counter Clockwise– Rotate the video 90 degrees counter clockwise.
Mirror Video – Flip the video across the vertical axis.
Mirror + 1 80 Degree Rotate – Flip the video across the vertical axis and rotate 180
degrees.
GOP Size
The Group of Pictures settings allow you to modify the frame structure of the video
stream. This setting changes the frequency of the I-frames that occur within the stream of
P-frames (2~64). Increasing this number increases the number of P-frames between each
I-frame; decreasing the file size of the stream, but increasing the risk of video decoding
errors. Decreasing this number decreases the number of P-Frames between each I-frame;
increasing the file size of the stream, but decreasing the risk of video decoding errors.
Toshiba recommends setting the GOP to be approximately twice the frame rate (e.g.: if
the frame rate is 10 IPS, then set the GOP to 20).
H.264 Profile
The H.264 Profile may need to be changed if you are using a third party recorder that is
not capable of decoding H.264 Main Profile video compression. Select compatible
compressi on type for each stream if necessary .
32953AC 35
Video Frame Rate
Setting the camera to transmit fewer frames can save
bandwidth. Use the Frame Rate Control screen to
adjust the frame rate of each stream.
Each of the MJPEG and H.264 streams can have a
separate frame rate setting from 1 to 30 frames per
second.
Note Higher frame rate will increase video
smoothness, as well as file size and
bandwidth usage.
Note Lower frame rate will decrease video
smoothness, as well as file size and
bandwidth usage.
36
Video Com pression
You can select an MJPEG / H.264 compression mode on the video compression page
appropriate for your application. You can also select to display compression inflation on
the Live Screen.
MJPEG compression settings include:
• High compression, low bitrate, low quality
• M iddle compre ssion, defa ult
• Low compression, high bitrate, high quality
H.264 compression settings include:
• 1024kbps, highest compression, lowest quality
• 2048kbps
• 4096kbp s, midd le co mpre ssion, default
• 6144kbps
• 8192kbps, low compression, highest quality
CBR Mode Setting
• The Constant Bit Rate mode allows you to lock in the bit rate of the H.264
stream. If this setting is not enabled, bit rate may fluctuate based on available
bandwidth.
32953AC 37
ADVANCED
SYSTEM SETTING
Network Setup
The Network Setup settings will automatically be set at the recommended default after the
camera connect ion is ma de.
DDNS
DDNS (Dynamic Domain Name Service) is a service that allows a connection to an IP
address using a hostname (URL) address instead of a numeric IP address. Most Internet
Service Providers use Dynamic IP Addressing that frequently changes the publ ic IP
address of your inter net con ne ctio n; this means that when co nnec ting to the camer a over
the internet, you need to know if your IP address has changed. DDNS automatically
redirects traffic to your current IP address when using the hostname address.
• Enable DDNS – Select the check box to enable DDNS.
• Provider – Select a DDNS host from the Provider list .
• Host name – Type the registered domain name in the field.
• Username/E-mail – Type the username or e-mail required by the DDNS provider
for authentication.
• Password/Key – Type the password or key required by the DDNS provider for
authentication.
Network Advanced
QoS
Quality of Service allows you to prioritize network traffic services of the camera’s
functions. The QoS function utilizes the Differentiated Services prioritized using Codepoint
vales (DSCP).
Note Routers and switches on the network must be QoS or DSCP capable, and have
these settings enable for this function to operate on your network.
38
SNMP Settings
With Simple Network Management Protocol (SNMP) enabled, the camera can be
monitored and managed remotely with a network management system. Contact your
network administrator if you are not familiar with SNMP setup.
UPnP (Universal Plug N’ Play)
• Enable UPnP – When enabled, the camera will appear in My Network Places on
Windows computers running UPnP on the same network.
• Enable UPnP Port Forwarding – Whe n enabl ed, the ca mera will attempt to
open the web server port on the router automatically.
• Friendly Name – Set a name to easily identify the camera.
32953AC 39
Network Security
HTTP
The camera can send alarm messages to a specific Hypertext Transfer Protocol (HTTP)
site when motion is detected or when the sensor input is activated. You can assign alarm
messages to up to two HTTP sites.
IP Filtering
IP Filtering allows you limit access to your IP cameras by IP address. You can “Allow” or
“Deny” a specific IP address by adding it to the appropriate list. IP addresses on the
“Allowed IP List” will be able to access the IP camera. IP addresses on the “Deny IP List”
will NOT be able to access the IP camera.
IEEE 802.1XSEA P-TLS
This is a well supported security protocol commonly used by wireless vendors. This
security method requires a valid CA certification and key. When properly configured, all
communication between the client (usually a recorder) and the camera is encrypted.
40
Alarm Application
The alarms menu is where alarm connections
are configured.
Alarm Switch – Designate when the alarm will
be active; Off, On, or By Schedule.
Alarm Type – Designate if the alarm is normally
open or normally closed.
• NOH – NO stands for Normally
Open.
• NC/L – NC stands for Normally
Closed.
Example: A door sticker consists of two contacts that are connected when under
normal conditions. This type of input would be a NC/L or normally closed alarm.
The alarm will trigger when the two contacts are no longer connected, such as an
abnormal condition when the door is opened.
Alarm Output – Choose high or low.
Trigger Action – Specify which actions the camera should take when motion is detected.
• Send Alarm Message by FTP / E-mail – Select to send an alarm message to a
configured FTP and/or e-mail address when motion is dete ct ed. When sending to
email, the alarm notification is text only. When sending to FRP, the alarm
notification will upload a text file to the FRP location.
• Upload Images by FTP – Select to assign an FTP site and configure various
parameters as shown in the figure below. W hen motion is detected, event
images will be uploaded to the appointed FRP site.
• Upload Image by E-mail – Select to assign an e-mail address and configure
various parameters as shown in the figure below. When motion is detected,
event images will be sent to the appropriate e-mail address.
Note Make sure SMTP or FTP configuration has been completed. See the Mail and
FTP sections for more infor ma tion.
• File Name – Enter a file name in the box, ex. Image.jpg. The uploaded image’s
file name format can be set in this section. Select the one that meets your
requirements.
Consult the documentation to the sensor input device to determine which of these to use.
32953AC 41
Tamper ing and Network Fai lure Detection
Tampering Alarm – Turn the Tampering Alarm On, Off, or On By Schedule.
Tampering Duration – Designate the amount of time (in seconds) that tampering must
occur in order for a Tampering Alarm to activate.
Triggered Action – Designate the actions that will occur upon a Tampering Alarm
activating.
Network Failure Detection – Turn the Network Failure Detection On, Off, or On By
Schedule.
Detection Type – Designate the IP Address that will be tested and how often (in minutes).
Triggered Action – Designate the actions that will occur upon Network Failure Detection
activation.
42
Mail, HTTP a nd FTP Set up
The camera c an sen d an e-mail via Simple Mail Transfer Protocol (SMTP) when a variety
of events occur. SMTP is a protocol for sending e-mail mess ages betw een serv ers. SMTP
is a relatively simple, text-based protocol, where one or more recipients of a message are
specified and the message text is transferred. The configuration page is shown as follows:
Two sets of SMTP accounts can be configured. Each set includes SMTP Server, Account
Name, Password and E-mail Address settings. For SMTP server, contact your network
service provider for more specific informa tion .
SD Card
All Toshiba IP cameras include an integrated microSD™ card slot that can be used to
record video or images. The card slot is compatible with a microSD™ card up to 16GB.
Load Device Information – Displays the storage total size and free space information of
the included microSD™ card.
Current Rec ording Partition – Amount of space designated for recording on the
microSD card.
Format – Allows you to format the microSD card.
Eject – Safely eject the microSD card.
Recording List – Displays a list of files saved to the card. You can delete files from the
card, or save them to your local PC.
Note If you are using Windows Vista, 7, or 8, you will need to change the Snapshot
location. Windows UAC does not allow internet programs to write directly to C:\
for security reasons.
32953AC 43
Netw ork S har e
Network Share is a network protocol that runs a variety of different system platforms,
allowing for file sharing between computers operating on Windows and computers
operating on Unix. This serves as an additional storage type.
Configuration requires the host IP address, share name, and credentials. Once
configured, cameras can record events to the network share.
Note Network Share can be hosted on a Windows, Mac, or Linux system.
44
Recording Schedule
The recording schedule allows you to set up scheduled recording to the microSD™ card
or to Network Sharing.
Recording
This section allows you to define recording schedules for the camera.
For continuous recording:
1. Select type of Recording Storage.
• microSD card™: save recorded
data to the microSD™ card
located in the camera.
• Network Share: save recorded
data to the designated Network
Share location.
2. Select Always as the type of Recording
Schedule.
3. Click Save.
To set up scheduled recording:
1. Select type of Recording Storage.
2. Select Only during time frame as the type of Recording Schedule.
3. Use the appropriate check box to designate a day of the week.
4. Type a Start Time and Duration.
5. Click Save.
6. Repeat steps 3-5 for each desired day of the week until the desired schedule is
completed.
Note Start Time and Duration are measured in 24-hour format (HH:MM).
To delete a recording sc hedu l e:
1. Select Disable for the type of Recording Schedule.
—OR—
Click on the desired week day sch edul e and then cli ck Delete.
32953AC 45
Schedule
This section allows you to establish schedules to use in other section.
To create a schedule:
1. Select a Schedule set (1-10).
2. Check the desired week day check boxes.
3. Select Day or Night.
4. Designate a Start Time and Duration.
5. Click Save.
46
Interval Recording
32953AC 47
Maintenance
On the Maintenance page you can export the cameras current configuration, or import the
configuration for a camera. Use the factory default page to reset the IP Camera to factory
default settings if necessary.
Note Do not import configuration files from different models of cameras.
Configuration
Export Configuration:
1. Check the appropriate boxes for information that you want exported.
2. Click Export Configurations.
3. The .bin file will be saved.
Note The default location for exported configurations is C:\
Upload (Import) Configuration:
1. Click Browse in the Configuration Import box.
2. Select a .bin file that you want to import.
3. Click Import.
4. Click Yes when prompted that the import will cause a system reboot.
Factory Default
There are two factory default settings available: Full Restore that restores default settings
including network settings, and a Partial Restore that restores default settings excluding
network settings. A system reboot is also available; this preserves all settings.
Note If a Full Factory Default is used, you will need to use the Network Camera
Manger to find the desired camera(s) again.
48
Software
Note Make sure the software upgrade file is available before starting the software
upgrade.
1. Click Browse and find the upgrade file.
Note Do not change the file name, or the system will fail to find the file.
2. Select the file name from the list under Step 2.
3. Click Upgrade. The system will check to find the upgrade file, and then start to
upload the upgrade file. The upgrade status bar will display on the page. When it
reaches 100%, the viewer will return to Home page.
4. Close the internet browser.
5. Go to the Windows Control Panel and double-click Add or Remove Programs.
Locate the Camera Viewer software on the Currently installed programs list
and click Remove to uninstall the previous software version.
6. Open the internet browser again and log in to the camera. The system will
automatically download the new version of the Camera Viewer software.
PICTURE SETTING
Video Mask
You can use the video mask page to define a privacy mask to keep users from viewing
parts of the image. You can enable up to five privacy masks and choose a color to
obscure the live view form users.
Hot Spot
The Spot feature allows you to transmit different parts of the camera image on separate
streams. Each stream is displaying a portion of the image at the full size of a regular
image. This is useful for focusing on details in different areas of a single camera view.
Text Overlay
Text Overlay allows you to select text to be displayed over the video. Three options are
available: Date, Time, and a Custom String (up to 20 alphanumeric characters).
32953AC 49
STREAMING SETTING
Audio
Audio Input Grain – sets the amplification that the camera applies to the incoming audio
before transm itti ng.
Audio Output Delay – Sets a delay in the audio transmission. This is used when there is
significant lag in video transmission to help sync the audio and video.
Volume – Sets the audio output volume level (for listening to live audio).
Network Transfer – Sets the camera to continue transmitting audio even if the video
stops.
LOGOUT
The Logout tab allows you to switch between users.
1. Click Logout.
2. If prompted to close the browser window, click Yes.
3. Using the Network Camera Manager Software, select the camera you wish to
view in the Viewer Software.
4. Click Browse.
5. Login as the appropriate user.
50
SPECIFICATIONS
CAMERA SPECIFICATIONS
Model IKS-WR7022
Maximum Resolution 1080p (2MP)
Image Sensory Sony 1/2.8” CMOS
Video Compression H.264 / MPEG4 / MJPEG
Frame Rate 30IPS @ 1080p (2MP)
ONVIF Profile S
Streaming Up to 2 configurable streams
Browser S upoprt Internet Explorer (Active X)
Day / Night Digital Day / Night
Wide Dynamic Range T rue WDR
Lens 4 mm
Horizontal Field of View 86°
Iris F1.6 Fixed
Minimum Illumination
@ 30IRE Color: 2.4 Lux @ F1.6
B/W: 0.5 Lux @ F1.6
White Balance Auto, Manual, Preset
Auto White Balance
Range 2000 ~ 11000K
Backlight
Compensation Yes
Auto Gain Control Yes
IP Rating N/A (Indoor)
Operating Temperature 14°F (-10°C) ~ 122°F (50°C)
Active / Passive
Cooling Active (fan)
32953AC 51
Model IKS-WR7022
Power Consumption 8.2W Max
Rated Amperage 0.68A (12vDC)
Input Voltage PoE / 12vDC
PoE Class 0
Camera Weight 0.97 lbs (439 g)
Dimensions (W x H): 4.9" x 2.9" (125 mm x 74 mm)
Housing / Dome Cover White / Clear
Tilt / Rotation Tilt = 90º R ota te = 350º
Control Type PTZ control via network only
Presets 9
32953AA
www.toshibasecurity.com
1-877-855-1349
© 2015 Toshiba
All rights reserved. No part of this publication may be reproduced by any means without written
permission from Toshiba. The information in this publication is believed to be accurate in all
respects. However, Toshiba cannot assume responsibility for any consequences resulting from the
use thereof. The information contained herein is subject to change without notice. Revisions or new
editions to this publication may be issued to incorporate such changes.