Table of Contents
- About This Guide
- Get to Know Your Modem Router
- Connect the Hardware
- Log In to Your Modem Router
- Set Up Internet Connections
- TP-Link Cloud Service
- OneMeshTM with Seamless Roaming
- IPTV
- Guest Network
- USB Settings
- Parental Controls
- QoS
- Network Security
- NAT Forwarding
- VPN Server
- Specify Your Network Settings
- Administrate Your Network
- 16. 1. Set System Time
- 16. 2. Control LEDs
- 16. 3. Update the Firmware
- 16. 4. Back up and Restore Configuration Settings
- 16. 5. Reboot the Modem Router
- 16. 6. Change the Administrator Account
- 16. 7. Local Management
- 16. 8. Remote Management
- 16. 9. System Log
- 16. 10. Monitor the Internet Traffic Statistics
- 16. 11. CWMP Settings
- 16. 12. SNMP Settings
- Appendix: Troubleshooting
TP-Link Archer VR2100v User Manual
Displayed below is the user manual for Archer VR2100v by TP-Link which is a product in the Wireless Routers category. This manual has pages.
Related Manuals
© 2021 TP-Link 1910013055 REV1.0.1
User Guide
AC2100 Wireless MU-MIMO VDSL/ADSL Modem Router
Archer VR2100
Contents
About This Guide .........................................................................................................1
Chapter 1. Get to Know Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . .3
1. 1. Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. 2. Physical Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. 2. 1. Top Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1. 2. 2. Back Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1. 2. 3. Side Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 2. Connect the Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2. 1. Position Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. 2. Connect Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 3. Log In to Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 4. Set Up Internet Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4. 1. Use Quick Setup Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4. 2. Manually Set Up an Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4. 3. Test Internet Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4. 4. Set Up an IPv6 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4. 5. More Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. 5. 1. Wireless Router Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. 5. 2. 3G/4G Router Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Chapter 5. TP-Link Cloud Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5. 1. Register a TP-Link ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. 2. Change Your TP-Link ID Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5. 3. Manage the User TP-Link IDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5. 3. 1. Add an TP-Link ID to Manage the Router . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5. 3. 2. Remove TP-Link ID(s) From Managing the Router . . . . . . . . . . . . . . . . . . 23
5. 4. Manage the Router via TP-Link Tether App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5. 4. 1. Install the Tether App on Your Smartphones or Tablets . . . . . . . . . . . . 24
Chapter 6. OneMeshTM with Seamless Roaming. . . . . . . . . . . . . . . . . . . . . 25
6. 1. Set Up a OneMeshTM Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
6. 2. Manage Devices in the OneMeshTM Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Chapter 7. IPTV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Chapter 8. Guest Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
8. 1. Create a Network for Guests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8. 2. Customize Guest Network Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 9. USB Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
9. 1. Access the USB Storage Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9. 1. 1. Access the USB Device Locally . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
9. 1. 2. Access the USB Device Remotely . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
9. 1. 3. Customize the Access Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
9. 2. Media Sharing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
9. 3. 3G/4G Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
9. 3. 1. As a Backup Solution for Internet Access . . . . . . . . . . . . . . . . . . . . . . . . . 43
9. 3. 2. As the Only Way to Access the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Chapter 10. Parental Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Chapter 11. QoS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
11. 1. Prioritize Internet Traffic with QoS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
11. 2. Update the Database . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Chapter 12. Network Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
12. 1. Firewall & DoS Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
12. 2. Service Filtering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
12. 3. Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
12. 4. IP & MAC Binding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
12. 5. IPv6 Firewall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Chapter 13. NAT Forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
13. 1. Translate Address and Port by ALG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
13. 2. Share Local Resources over the Internet by Virtual Server . . . . . . . . . . . . . . . . . . . 65
13. 3. Open Ports Dynamically by Port Triggering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
13. 4. Make Applications Free from Port Restriction by DMZ . . . . . . . . . . . . . . . . . . . . . . . 67
13. 5. Make Xbox Online Games Run Smoothly by UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Chapter 14. VPN Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
14. 1. Use OpenVPN to Access Your Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
14. 2. Use PPTP VPN to Access Your Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
14. 3. Use IPSec VPN to Access Your Home Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Chapter 15. Specify Your Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 80
15. 1. LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
15. 1. 1. Change the LAN IP Address. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
15. 1. 2. Use the Modem Router as a DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . 82
15. 1. 3. Reserve LAN IP Addresses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
15. 2. IPv6 LAN Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
15. 2. 1. Configure the RADVD Address Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
15. 2. 2. Configure the DHCPv6 Server Address Type . . . . . . . . . . . . . . . . . . . . . . 84
15. 3. Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
15. 3. 1. Specify Basic Wireless Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
15. 3. 2. Use WPS for Wireless Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
15. 3. 3. Schedule Your Wireless Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
15. 3. 4. View Wireless Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
15. 3. 5. Advanced Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
15. 4. Set Up a Dynamic DNS Service Account . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
15. 5. Create Static Routes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
15. 6. Set Up the IPv6 Tunnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
15. 6. 1. Use the Public IPv6 Tunnel Service-6to4 . . . . . . . . . . . . . . . . . . . . . . . . . . 96
15. 6. 2. Specify the 6rd Tunnel with Parameters Provided by Your ISP. . . . . . 97
Chapter 16. Administrate Your Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
16. 1. Set System Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
16. 2. Control LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
16. 3. Update the Firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
16. 3. 1. Online Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
16. 3. 2. Local Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
16. 4. Back up and Restore Configuration Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
16. 5. Reboot the Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
16. 6. Change the Administrator Account. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
16. 7. Local Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
16. 8. Remote Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
16. 9. System Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
16. 10. Monitor the Internet Traffic Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
16. 11. CWMP Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
16. 12. SNMP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .111
Appendix: Troubleshooting ............................................................................... 113
1
About This Guide
This guide is a complement to Quick Installation Guide. The Quick Installation Guide
provides instructions for quick internet setup, while this guide contains details of each
function and demonstrates how to configure them in typical scenarios.
Features available in the modem router may vary by model and software version. Modem
router availability may also vary by region or ISP. All images, steps, and descriptions in
this guide are only examples and may not reflect your actual modem router experience.
Conventions
In this guide, the following conventions are used:
Convention Description
Underline Hyperlinks are in teal and underlined. You can click to redirect to a website
or a specific section.
Teal Key information appears in teal, including management page text such as
menus, items, buttons and so on.
>
The menu structures to show the path to load the corresponding page. For
example, Advanced > Wireless > MAC Filtering means the MAC Filtering
function page is under the Wireless menu that is located in the Advanced
tab.
Note: Ignoring this type of note might result in a malfunction or damage to the
device.
Tips: Indicates important information that helps you make better use of your
device.
Symbols on
the web page
• click to edit the corresponding entry.
• click to delete the corresponding entry.
• click to enable or disable the corresponding entry.
• click to view more information about items on the page.
Speed/Coverage Disclaimer
Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11
specifications. Range, coverage, and maximum quantity of connected devices are
based on test results under normal usage conditions. Actual wireless data throughput,
wireless coverage, and quantity of connected devices are not guaranteed and will vary
as a result of 1) environmental factors, including building materials, physical objects,
and obstacles, 2) network conditions, including local interference, volume and density
of traffic, product location, network complexity, and network overhead, and 3) client
limitations, including rated performance, location, connection quality, and client
condition.
*Use of MU-MIMO requires clients to also support MU-MIMO.
2
More Info
• The latest firmware and management app are available from the Download Center at
https://www.tp-link.com/support/download/.
• The Quick Installation Guide (QIG) can be found where you find this guide or inside the
product packaging.
• Specifications can be found on the product page at https://www.tp-link.com.
• TP-Link Community is provided for you to share knowledge and discuss our products
at https://community.tp-link.com.
• Our Technical Support contact information can be found at the Contact Technical
Support page at https://www.tp-link.com/support.
4
Chapter 1
1. 1. Product Overview
TP-Link’s modem router is a combined wired/wireless network connection device with
wireless router and DSL modem capabilities.
With DSL and LAN/WAN ports, the modem router is compatible with DSL connections
and fiber/cable access.
Ethernet ports and adjustable antennas enable the modem router to provide wired and
wireless access for multiple computers and mobile devices.
With an array of additional features, the modem router is the perfect hub for your home
or business network.
1. 2. Physical Appearance
1. 2. 1. Top Panel
The modem router’s LEDs are located on the top panel. You can check the modem
router’s working status by following the LED Explanation table.
It also provides the LED On/Off button. You can press the button to turn on/off the LEDs
without affecting the modem router’s function.
LED On/Off Button
5
Chapter 1
LED Explanation
Name Status Indication
Power
On The system has started up successfully.
Flashing The system is starting up or firmware is being upgraded.
Do not disconnect or power off your modem router.
Off Power is off. Please ensure that the power adapter is
connected correctly.
DSL
On DSL synchronization is complete.
Flashing DSL synchronization is in progress.
Off DSL synchronization failed. Please refer to Note 1 for
troubleshooting.
Internet
On Internet service is available.
Orange Internet connection is correct but internet service is
unavailable. Please refer to Note 2 for troubleshooting.
Off
Internet connection is incorrect, DSL synchronization
failed, or the modem router is operating in Bridge mode.
Please refer to Note 3 for troubleshooting.
Wireless 2.4GHz
/
Wireless 5GHz
On The wireless 2.4GHz/5GHz band is working properly.
Off The wireless 2.4GHz/5GHz band is disabled.
LAN
On At least one LAN port is connected to a powered-on
device.
Off No LAN port is connected to a powered-on device.
USB
On The USB device is ready to use.
Flashing The USB device is being identified.
Off No USB device is plugged into the USB port.
WPS
On A wireless device has been successfully added to the
network by WPS.
Flashing
WPS handshaking is in process and will continue for
about 2 minutes. Please press the WPS button on other
wireless devices that you want to add to the network
while the LED is flashing.
Off A wireless device has failed to be added to the network
by WPS.
Note:
1. If the DSL LED is off, please check your internet connection. Refer to Connect Your Modem Router for more
information about how to connect to the internet correctly. If you have already made a successful connection, please
contact your ISP to make sure your internet service is available now.
2. If the Internet LED is orange, please check your internet configuration. You may need to check this information with
your ISP and make sure everything has been input correctly.
6
Chapter 1
3. If the Internet LED is off, please check your DSL LED first. If your DSL LED is also off, please refer to Note 1. If your
DSL LED is ON, reconnect your modem router correctly by referring to related guide.
1. 2. 2. Back Panel
The modem router’s back panel shows the ports, buttons and antennas. Refer to the
following for detailed instructions.
Item Description
Power Port For connecting the modem router to a power socket via the provided
power adapter.
LAN1, LAN2, LAN3,
LAN4/WAN Port
For connecting the modem router to your PC or other Ethernet network
devices. In wireless router mode, the LAN4/WAN port is used for
connecting to a Cable/FTTH/VDSL/ADSL device.
Reset Button Press and hold down for 8 seconds to reset the modem router into
factory default settings.
DSL Port
For connecting the modem router to the internet. Connect the port to
the splitter or directly connect the port to the phone jack via a phone
cable. For details, please refer to Connect Your Modem Router.
Antennas Used for wireless data transmission. Position them upright for the best
performance.
7
Chapter 1
1. 2. 3. Side Panel
The modem router’s side panel shows the buttons and ports. Refer to the following for
detailed instructions.
Item Description
USB Port For connecting to a USB storage device.
Wi-Fi Button Press to turn both 2.4GHz and 5GHz Wi-Fi on or off.
WPS Button Press to start a WPS synchronization.
Power On/Off
Button The switch for the power. Press it to power on or off the modem router.
9
Chapter 2
2. 1. Position Your Modem Router
With the modem router, you can access your network from anywhere within the
wireless network coverage. However, the wireless signal strength and coverage varies
depending on the environment your modem router is in. Obstacles may limit the range
of the wireless signal, for example, concrete structures, thick walls.
For best Wi-Fi performance, and to keep your network secure:
• Do not locate the modem router in a place where it will be exposed to moisture or
excessive heat.
• Keep the product away from strong electromagnetic radiation and devices that emit
electromagnetic waves.
• Place the modem router in a location where it can be connected to the various devices
as well as to a power source.
• Make sure the cables and power cord are safely placed out of the way so they do not
create a tripping hazard.
Generally, the modem router is placed on a horizontal surface, such as a shelf or
desktop. The device also can be mounted on the wall as shown below.
3
1. 5
4. 69
13. 09
5. 54
10
84
A
截面 A-A
A(2/1)
A
A
D
NOTE:
4.69mm<D<10mm
H
H<3mm
Note:
The diameter of the screw is 4.69mm<D<10mm, and the distance of two screws is 84mm. The screw that project from
the wall need around 8mm based, and the length of the screw need to be at least 20mm to withstand the weight of the
product.
2. 2. Connect Your Modem Router
Follow the steps below to connect your modem router.
1. Connect the DSL line and power adapter. The electrical outlet shall be installed
near the device and shall be easily accessible.
10
Chapter 2
Attach the
antennas.
1
Phone Cable
Phone Cable
DSL Splitter
Phone (Optional)
2
3
Modem Router
If you don’t need the phone service, just directly connect the modem
router to the phone jack with the provided phone cable, then follow
steps 4 and 5 to complete the hardware connection.
Power AdapterPhone Jack
Power LAN2LAN1 LAN3 LAN4/WAN DSL
PHONE
LINE
MODEM
4Push in the Power button
on the side panel to turn
on the modem router.
Power On DSL On
Verify that the following LEDs
turn stable before continuing
with the conguration.
5
Notes:
2. We recommend that the outside
two antennas be outward at about
30 degrees.
1. The DSL LED takes about 1 to 2
minutes to stabilize.
30° 30°
Power LAN2LAN1 LAN3 LAN4/WAN DSL
Power LAN2LAN1 LAN3 LAN4/WAN DSL
2. Connect your computer to the modem router.
Method 1: Wired
Connect your computer’s Ethernet port to the LAN port on the modem router via the
Ethernet cable.
Method 2: Wirelessly
Use the default SSID (Wireless Network Name) and Wireless Password printed on
the included Wi-Fi Info Card or on the product label of the modem router to connect
wirelessly.
Method 3: Use the WPS button
Wireless devices that support WPS, including Android phones, tablets, most USB
network cards, can be connected to your router through this method. (WPS is not
supported by iOS devices.)
Note:
The WPS function cannot be configured if the wireless function of the router is disabled. Also, the WPS function will be
disabled if your wireless encryption is WEP. Please make sure the wireless function is enabled and is configured with the
appropriate encryption before configuring the WPS.
1 ) Tap the WPS icon on the device’s screen.
2 ) Immediately press the WPS button on your modem router.
3 ) The WPS LED flashes for about two minutes during the WPS process.
4 ) When the WPS LED stabilizes and remains on, the client device has successfully
connected to the modem router.
11
Chapter 2
Chapter 3
Log In to Your Modem
Router
13
Chapter 3 Log In to Your Modem Router
With the web management page, it is easy to configure and manage the modem router.
The web management page can be used on any Windows, Macintosh or UNIX OS with a
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
Follow the steps below to log in to your modem router.
1. If the TCP/IP Protocol on your computer is set to the static (fixed) IP address, you
need to change its settings to obtain an IP address automatically. Refer to Appendix:
Troubleshooting to configure your computer.
2. Launch a web browser and go to http://tplinkmodem.net or http://192.168.1.1.
Create a strong password and click Let’s Get Started to log in.
Note:
If you have registered a TP-Link ID and bind your cloud router to it, the login password you created here should be
ineffective. Please log in to the cloud router using your TP-Link ID.
Chapter 4
Set Up Internet
Connections
This chapter introduces how to connect your modem router to the internet. The
modem router is equipped with a web-based Quick Setup wizard. It has many ISP
information built in, automates many of the steps and verifies that those steps have
been successfully completed. Furthermore, you can also set up an IPv6 connection if
your ISP provides IPv6 service.
This chapter includes the following sections:
• Use Quick Setup Wizard
• Manually Set Up an Internet Connection
• Test Internet Connectivity
• Set Up an IPv6 Connection
• More Operation Modes
15
Chapter 4 Set Up Internet Connections
4. 1. Use Quick Setup Wizard
1. Visit http://tplinkmodem.net, and log in with the password you set for the modem
router.
2. Click Quick Setup on the top of the page. Then follow the step-by-step instructions
to connect your router to the internet.
3. To enjoy a more complete service from TP-Link (remote management, TP-Link
DDNS, etc.), log in with your TP-Link ID or click Register Now to get one. Then follow
the instructions to bind the modem router to your TP-Link ID.
Note:
1. To learn more about the TP-Link Cloud service, please refer to the TP-Link Cloud section.
2. If you do not want to register a TP-Link ID for now, you may click Log In Later to proceed.
3. If you have changed the preset wireless network name (SSID) and wireless password during the Quick Setup process,
all your wireless devices must use the new SSID and password to connect to the router.
4. 2. Manually Set Up an Internet Connection
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
2. Go to Basic > Internet page. Select your ISP, and related information will be
automatically filled in. For some ISPs, you may need to manually specify some
information provided. If you can’t find your ISP in the ISP List, select Other and then
enter the information provided by your ISP.
16
Chapter 4 Set Up Internet Connections
3. Click Save to make the settings effective, and you can refer to Test Internet
Connectivity to test the internet connection.
Tips: You can view and edit all internet connection settings on the Advanced > Network > Internet page.
4. 3. Test Internet Connectivity
After manually setting up the internet connection, you need to test the internet
connectivity. The modem router provides a diagnostic tool to help you locate the source
of any problems.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
2. Go to Advanced > System Tools > Diagnostics page.
17
Chapter 4 Set Up Internet Connections
3. Click Start to test the internet connectivity and you will see the test result in the
gray box.
4. 4. Set Up an IPv6 Connection
If your ISP has provided a DSL line that supports IPv6 connection as well as some
detailed IPv6 parameters, you can manually set up an IPv6 connection.
If your ISP provides an IPv4-only connection or IPv6 tunnel service, permit IPv6
connection by referring to Set Up the IPv6 Tunnel.
Follow the steps below to set up an IPv6 connection:
1. Make sure you have set up an IPv4 connection either manually or by using the Quick
Setup wizard before setting up an IPv6 connection.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
3. Go to Advanced > Network > Internet page.
4. Select your WAN Interface Name (Status should be Connect) and click the (Edit)
icon.
18
Chapter 4 Set Up Internet Connections
5. Scroll down the page, enable IPv6, and configure the IPv6 parameters.
• Addressing Type: Consult your ISP for the addressing type (DHCP or SLAAC).
SLAAC is the most commonly used addressing type.
• IPv6 Gateway: Keep the default setting as Current Connection.
Note: If your ISP has provided the IPv6 address, click Advanced to reveal more settings. Check to use IPv6
specified by ISP and enter the parameters provided by your ISP.
6. Click Save to make the settings effective. Now IPv6 service is available for your
network.
4. 5. More Operation Modes
The modem router supports two more operation modes: Wireless Router mode and
3G/4G Router mode. You can change the mode according to your needs.
4. 5. 1. Wireless Router Mode
If you already have a modem or your internet comes via an Ethernet jack on the wall, you
can set up the modem router as a regular wireless router to share the internet.
1. Find the WAN port (labeled as LAN4/WAN) on the modem router, and connect it
to your existing modem or the Ethernet jack on the wall. Then connect the power
adapter and turn on the modem router. If you connect an existing modem, reboot it
to get the modem router connected to the internet.
2. Connect your computer to the modem router. For details, refer to Connect Your
Modem Router.
3. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
4. Go to Advanced > Operation Mode, select the Wireless Router Mode, and click
Save. The modem router will reboot.
19
Chapter 4 Set Up Internet Connections
5. Go to Basic > Internet, select the Connection Type, and enter the information
provided by your ISP.
6. Click Save to make the settings effective.
Tips:
1. You can view and edit all internet connections on Advanced > Network > Internet page.
2. In the Wireless Router Mode, you can also permit IPv6 connection by setting up an IPv6 connection or the IPv6 tunnel
just as in the DSL Modem Router Mode. For details, refer to Set Up an IPv6 Connection and Set Up the IPv6 Tunnel.
4. 5. 2. 3G/4G Router Mode
The modem router can be used as a 3G/4G wireless router if you have a 3G/4G USB
modem. There are two ways to use your 3G/4G network:
• As a backup solution for internet access
Use this way if you have set up an internet connection successfully and want to use the
3G/4G network as a backup network. Your modem router will be directly connected to
the 3G/4G network when the original network service fails. For detailed instructions,
refer to As a Backup Solution for Internet Access.
• As the only way to access the internet
Use this way if wired internet access is not available and you can only use the 3G/4G
network to access the internet. For detailed instructions, refer to As the Only Way to
Access the Internet.
Tips:
In the 3G/4G Router Mode, you can also permit IPv6 connection by setting up the IPv6 tunnel just as in the DSL Modem
Router Mode. For details, refer to Set Up the IPv6 Tunnel.
Chapter 5
TP-Link Cloud Service
TP-Link Cloud service provides a better way to manage your cloud devices. Log in to
your router with a TP-Link ID, and you can easily monitor and manage your home network
when you are out and about via the Tether app on your smartphone or tablet. To ensure
that your router stays new and gets better over time, the TP-Link Cloud will notify you
when an important firmware upgrade is available. Surely you can also manage multiple
TP-Link Cloud devices with a single TP-Link ID.
This chapter introduces how to register a new TP-Link ID, bind or unbind TP-Link IDs
to manage your router, and the Tether app with which you can manage your home
network no matter where you may find yourself.
It contains the following sections:
• Register a TP-Link ID
• Change Your TP-Link ID Information
• Manage the User TP-Link IDs
• Manage the Router via TP-Link Tether App
21
Chapter 5 TP-Link Cloud Service
5. 1. Register a TP-Link ID
If you have skipped the registration during the Quick Setup process, you can:
1. Visit http://tplinkmodem.net, and log in with the password you set for the router.
2. Go to Basic > TP-Link Cloud.
3. Click Register Now and follow the instructions to register a TP-Link ID.
4. After activating your TP-Link ID, come back to the TP-Link Cloud page to log in. The
first-time login TP-Link ID will be bound automatically to your cloud router as an
Admin.
Note:
• The TP-Link ID also can be registered via the TP-Link Tether app. Please refer to Install the Tether App on Your
Smartphones or Tablets to install the app. Launch the app, tap in the top-left corner of the screen and tap Login,
and then click New User to register a new one.
• If you want to unbind the admin TP-Link ID from your router, please go to Basic > TP-Link Cloud, click Unbind in the
Device Information section.
5. 2. Change Your TP-Link ID Information
Follow the steps below to change your email address and password of your TP-Link ID
as needed.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID.
2. Go to Basic > TP-Link Cloud, and focus on the Account Information section.
• Change your email address
1. Click behind the Email.
2. Enter the password of your TP-Link ID, then the new email address. And click Save.
22
Chapter 5 TP-Link Cloud Service
• Change your password
1. Click behind the Password.
2. Enter the current password, then a new password twice. And click Save.
5. 3. Manage the User TP-Link IDs
The first-time login TP-Link ID will be bound automatically to your router as an Admin
account. An admin account can add or remove other TP-Link IDs to the same router
as Users. Admin account and User accounts both can monitor and manage the router
locally or remotely, except that user accounts cannot:
• Reset the router to factory default settings from the web management page or Tether app.
• Add/remove other TP-Link IDs to/from the router.
23
Chapter 5 TP-Link Cloud Service
5. 3. 1. Add an TP-Link ID to Manage the Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID.
2. Go to Basic > TP-Link Cloud, and focus on the Bound Accounts section.
3. Click , enter another TP-Link ID as needed and click Save.
Note:
If you need another TP-Link ID, please refer to Install the Tether App on Your Smartphones or Tablets to install the app.
Launch the app, tap in the top-left corner of the screen and tap Login, and then click New User to register a new one.
4. The new TP-Link ID will be displayed in the Bound Accounts table as a User.
5. 3. 2. Remove TP-Link ID(s) From Managing the Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID.
2. Go to Basic > TP-Link Cloud, and focus on the Bound Accounts section.
3. Check the box(es) of the TP-Link ID(s) you want to remove and click Unbind.
24
Chapter 5 TP-Link Cloud Service
5. 4. Manage the Router via TP-Link Tether App
5. 4. 1. Install the Tether App on Your Smartphones or Tablets
The Tether app runs on iOS and Android devices like smartphones and tablets.
1. Open the Apple App Store or Google Play and search the key word TP-Link Tether
or simply scan the QR code to download and install the app.
OR
2. Launch the Tether app and log in with your TP-Link ID. If you don’t have a TP-Link ID,
create one first.
3. Connect your device to the modem router’s wireless network.
4. Go back to the Tether app, select the model of your router and log in with the
password you set for the modem router.
5. Manage your modem router as needed.
26
Chapter 6 OneMeshTM with Seamless Roaming
TP-Link OneMeshTM router and TP-Link OneMeshTM extenders work together to
form one unified Wi-Fi network. Walk through your home and stay connected with the
fastest possible speeds thanks to OneMesh’s seamless coverage.
Unified Wi-Fi Network
Router and extenders share the same wireless settings, including network name,
password, access control settings and more.
Seamless Roaming
Devices automatically switch between your router and extenders as you move
through your home for the fastest possible speeds.
Easy Setup and Management
Set up a OneMeshTM network with a push of WPS buttons. Manage all network devices
on the Tether app or at your router’s web management page.
Unified OneMeshTM Network
INTERN E T
SAME
Network Name & Password
for Seamless Roaming
6. 1. Set Up a OneMeshTM Network
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Basic > OneMesh or Advanced > Wireless > OneMesh.
27
Chapter 6 OneMeshTM with Seamless Roaming
Note:
Early firmware versions may not support OneMeshTM. If you can’t find the OneMesh page, please upgrade your router
to the latest firmware version. For upgrade instructions, refer to Update the Firmware.
3. Connect one or more OneMeshTM extenders to this router by following the setup
instructions in the extenders’ manuals.
Note:
To check full list of TP-Link OneMeshTM devices, visit https://www.tp-link.com/onemesh/compatibility.
4. If you have set up an extender to join the OneMeshTM network, it will be listed in the
Devices in OneMesh Network list. Otherwise, you need to find it in the Available
OneMesh Devices list and click Add to add it to the OneMeshTM network.
Now your router and extenders successfully form one OneMeshTM network!
6. 2. Manage Devices in the OneMeshTM Network
In a OneMeshTM network, you can manage all mesh devices and clients on your router’s
web page.
28
Chapter 6 OneMeshTM with Seamless Roaming
• To view all mesh devices and clients in the OneMeshTM network:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Basic > Network Map.
3. Click the Mesh Devices, Wired Clients, or Wireless Clients icon to view the related
device or client list.
• To manage each OneMeshTM device in the network:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Basic > OneMesh or Advanced > Wireless > OneMesh.
29
Chapter 6 OneMeshTM with Seamless Roaming
3. Click a OneMeshTM device to view the device information, or click <number> Clients
to view the clients connected to this device.
On the Device Info page, you can:
• Click Manage Device to redirect to the web mangement page of this OneMeshTM
device.
• Click Leave OneMesh to delete this device from the OneMeshTM network.
Chapter 7
IPTV
IPTV is the abbreviation of Internet Protocol Television. The service can only be delivered
through the Internet, and our modem router provides a specific LAN port for IPTV.
By automatically separating IPTV from Internet surfing, you can enjoy a high quality of
video streaming and fast browsing speeds at the same time.
31
Chapter 7
I want to:
Configure the modem router to enable Internet Protocol Television (IPTV) Services.
For example, I already bought IPTV service, but this service can only be delivered
through the Internet. Therefore, I need to configure my modem router first.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > IPTV to open the configuration page.
3. Check Enable to enable IPTV function.
4. Select your ISP from the Profile drop-down listand and then the VLAN ID will be
automatically filled in. If your ISP is not listed, select Others and then configure your
VLAN ID using the parameters provided by your IPTV service provider.
5. Select a connection type from the Profile drop-down listand according to your IPTV
connection. If you select Bridge, specify a LAN port for the IPTV connection and
connect the set-top box to this port.
6. Click Save to make the settings effective.
Done!
Modem router configuration is complete! You may still need to configure settings on
your set-top box before enjoying your IPTV service.
Chapter 8
Guest Network
This function allows you to provide Wi-Fi access for guests without disclosing your
main network. When you have guests in your house, apartment, or workplace, you can
create a guest network for them. In addition, you can assign network authorities and
bandwidth for guests to ensure network security, privacy, and fluency.
• Create a Network for Guests
• Customize Guest Network Options
33
Chapter 8 Guest Network
8. 1. Create a Network for Guests
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Guest Network. Locate the Wireless Settings section.
3. Create 2.4GHz and 5GHz guest network according to your needs.
1 ) Enable 2.4GHz Wireless or 5GHz Wireless or enable both according to your
needs.
2 ) Set an easy-to-identify SSID. Don‘t select Hide SSID unless you want your
guests and other people to manually input this SSID for Wi-Fi access.
3 ) Set Security to WPA/WPA2 Personal, keep the default Version and Encryption
values, and set an easy-to-remember password. 2.4GHz and 5GHz guest
networks share the same password.
4. Click Save. Now your guests can access your guest network using the SSID and
password you set!
Tips:
To view guest network information, go to Advanced > Status and find the Guest Network section.
8. 2. Customize Guest Network Options
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Guest Network.
34
Chapter 8 Guest Network
3. Assign network authorities and bandwidth according to your needs.
• Allow Guests to Access Each Other
Select this check box to allow the clients in your guest network to access each
other’s files.
• Allow Guests to Access My Local Network
Select this check box to allow the clients in your guest network to access your local
network, not just the internet.
• Allow Guests to Access My USB Storage Sharing
Select this check box to allow the clients in your guest network to access your
router’s USB storage sharing.
• Enable QoS for Guest Network
Select this check box to set the QoS Priority of the guest network. This option is
available only when QoS is enabled on the Advanced > QoS page.
4. Click Save. Now users in your guest network can enjoy only the network authorities
at the priority you assigned!
Tips:
To view guest network information, go to Advanced > Status and find the Guest Network section.
Chapter 9
USB Settings
This chapter describes how to use the USB ports to share files, and media from the USB
storage devices over your home network locally, or remotely through the internet.
The modem router supports USB external flash drives, and hard drives.
This chapter contains the following sections:
• Access the USB Storage Device
• Media Sharing
• 3G/4G Settings
36
Chapter 9 USB Settings
9. 1. Access the USB Storage Device
Insert your USB storage device into the modem router’s USB port and then access files
stored there locally or remotely.
Tips:
• If you use USB hubs, make sure no more than 4 devices are connected to the modem router.
• If the USB storage device requires using bundled external power, make sure the external power has been
connected.
• If you use a USB hard drive, make sure its file system is FAT32 or NTFS. Some modem routers also support
the HFS+ and exFAT file systems.
• Before you physically disconnect a USB device from the modem router, safely remove it to avoid data
damage: Go to Advanced > USB Sharing > USB Storage Device and click .
9. 1. 1. Access the USB Device Locally
Insert your USB storage device into the modem router’s USB port and then refer to the
following table to access files stored on your USB storage device:
Windows
computer
• Method 1:
Go to Computer > Network, then click the Network Server Name
(ARCHER_model number by default) in the Computer section.
Note:
1. Operations in different systems are similar. Here we take Windows 7 as an example.
2. Network Server Name can be customized on the web management page.
37
Chapter 9 USB Settings
Windows
computer
• Method 2:
Open the Windows Explorer (or go to Computer) and type the server
address \\tplinkmodem.net or ftp://tplinkmodem.net in the address
bar, then press Enter.
Mac
1 ) Select Go > Connect to Server
2 ) Type the server address smb://tplinkmodem.net
3 ) Click Connect
4 ) When prompted, select the Guest radio box. (If you have set up
a username and a password to deny anonymous access to the
USB disks, you should select the Registered User radio box. To
learn how to set up an account for the access, refer to To Set up
Authentication for Data Security.)
Tips:
You can also use the FTP, http and SFTP methods to access the USB storage device.
Tablet Use a third-party app for network files management.
9. 1. 2. Access the USB Device Remotely
You can access your USB disk outside the local area network. For example, you can:
38
Chapter 9 USB Settings
• Share photos and other large files with your friends without logging in to (and paying
for) a photo-sharing site or email system.
• Get a safe backup for the materials for a presentation.
• Save and remove the files on your camera’s memory card during your travels.
Note:
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), you cannot use this feature because
private addresses are not routed on the internet.
Follow the steps below to configure remote access settings.
1. Visit http://tplinkmodem.net, then log in with your TP-Link ID or the password you
set for the modem router.
2. Go to Advanced > USB Sharing > USB Storage Device page and locate the Sharing
Settings section.
3. Select the check box to enable FTP (via Internet), or https (via Internet), or SFTP (via
Internet), then click Save.
4. Refer to the following table to access your USB disk remotely.
39
Chapter 9 USB Settings
Windows
computer
1 ) Open the Windows Explorer (or go to Computer, only for
Windows users) or open a web browser.
2 ) Type the server address in the address bar:
Type in ftp://<WAN IP address of the modem router>:<port
number> (such as ftp://59.40.2.243:21). If you have specified
the domain name of the modem router, you can also type
in ftp://<domain name>:<port number> (such as ftp://
MyDomainName:21)
3 ) Press Enter on the keyboard.
4 ) Access with the username and password you set in To Set up
Authentication for Data Security.
Tips:
You can also access the USB disk via a third-party app for network files management, which
can resume broken file transfers.
Tablet Use a third-party app for network files management.
Tips:
Click Set Up a Dynamic DNS Service Account to learn how to set up a domain name for your modem router.
9. 1. 3. Customize the Access Settings
By default, all the network clients can access all folders on your USB disk. You can
customize your sharing settings by setting a sharing account, sharing specific contents
and setting a new sharing address on the modem router’s web management page.
1. Visit http://tplinkmodem.net, then log in with your TP-Link ID or the password you
set for the modem router.
2. Go to Advanced > USB Sharing > USB Storage Device page.
• To Customize the Address of the USB Disk
You can customize the server name and use the name to access your USB disk.
1. On the Sharing Settings part, make sure Network Neighborhood is ticked, and enter
a Network/Media Server Name as you like, such as MyShare, then click Save.
40
Chapter 9 USB Settings
2. Now you can access the USB disk by visiting \\MyShare (for Windows) or smb://
MyShare (for Mac).
• To Only Share Specific Content
1. Focus on the Folder Sharing section. Click the button to disable Share All, then click
Add to add a new sharing folder.
2. Select the Volume Name and Folder Path, then enter a Folder Name as you like.
3. Decide the way you share the folder:
41
Chapter 9 USB Settings
• Enable Authentication: Select to enable authentication for this folder sharing,
and you will be required to log in to the Sharing Account to access the USB disk.
Refer to To Set up Authentication for Data Security to learn more.
• Enable Write Access: If you tick this check box, network clients can modify this
folder.
• Enable Media Sharing: Tick to enable media sharing for this folder, and you can
view photos, play music and watch movies stored on the USB disk directly from
DLNA-supported devices. Refer to Media Sharing to learn more.
4. Click Save.
Tips:
The modem router can share eight volumes at most. You can click on the page to detach the corresponding volume
you do not need to share.
• To Set up Authentication for Data Security
You can set up authentication for your USB device so that network clients will be
required to enter the username and password when accessing the USB disk.
1. Under Sharing Account, choose Use Default Account or Use New Account. The
username and password are both admin for the default account. If your choose
Use New Account, you have to customize the username and a password.
Note:
For Windows users, do not set the sharing username the same as the Windows username. Otherwise, Windows
credential mechanism may cause the following problems:
• If the sharing password is also the same as the Windows password, authentication will not work since the Windows
system will automatically use its account information for USB access.
• If the sharing password is different from the Windows password, the Windows system will be unable to remember
your credentials and you will always be required to enter the sharing password for USB access.
42
Chapter 9 USB Settings
2. Specify the folder(s) to enable authentication.
• If you want to enable authentication for all folders, leave Share All enabled, and
toggle on Enable Authentication.
• If you want to enable authentication for specific folders, disable Share All and
click Add to specify the folders, and select Enable Authentication.
Note:
Due to Windows credential mechanism, you might be unable to access the USB disk after changing Authentication
settings. Please log out from the Windows and try to access again. Or you can change the address of the USB disk by
referring to To Customize the Address of the USB Disk.
9. 2. Media Sharing
Media Sharing allows you to view photos, play music and watch movies stored on the
USB disk directly from DLNA-supported devices, such as your computer, tablet or
games console.
1. When your USB disk is inserted into the modem router, your DLNA-supported
devices (such as your computer and tablet) connected to the modem router can
detect and play the media files on the USB disks.
43
Chapter 9 USB Settings
2. Refer to the following table for detailed instructions.
Windows
Computer
• Go to Computer > Network, then click the Media Server Name (Archer_
model number by default) in the Media Devices section.
Note:
Here we take Windows 7 as an example.
Smart
device • Use a third-party DLNA-supported player.
9. 3. 3G/4G Settings
The modem router can be used as a 3G/4G wireless router if you have a 3G/4G USB
modem. There are two ways to use your 3G/4G network:
• As a backup solution for internet access
• As the only way to access the internet
9. 3. 1. As a Backup Solution for Internet Access
Using 3G/4G network as a backup solution for internet access, your modem router will
be directly connected to the 3G/4G network when the original network service fails.
Follow the steps below to set your 3G/4G network as a backup for internet access:
44
Chapter 9 USB Settings
1. Plug your USB modem into the USB port of your modem router.
2. Visit http://tplinkmodem.net, then log in with your TP-Link ID or the password you
set for the modem router.
3. Go to Advanced > USB Settings > 3G/4G Settings, and select the box of Enable
3G/4G as a backup solution for Internet access.
4. Verify that your 3G/4G USB Modem is successfully identified.
Note:
The 3G/4G USB modem will not be identified if it is incompatible with the modem router. Find the 3G/4G Compatibility List
on the web page: http://www.tp-link.com/en/comp-list.html. If your USB modem is incompatible, contact our technical
support.
5. Verify that the modem router has correctly recognized your Mobile ISP. When your
Mobile ISP is correct, you have successfully set 3G/4G network as a backup solution
for internet access. Otherwise, select the box Set the Dial Number, APN, Username
and Password manually and enter the information provided by your 3G/4G network
service provider.
6. Click Advanced to have more configurations if needed.
7. Click Save to make the settings effective.
45
Chapter 9 USB Settings
9. 3. 2. As the Only Way to Access the Internet
If you want the 3G/4G network to be your only way to access the internet, follow the
steps below to configure:
1. Plug your USB modem into the USB port of your modem router.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
3. Go to Advanced > Operation Mode and choose 3G/4G Router Mode.
4. Click Save and when the modem router is successfully rebooted, the settings will
be effective.
5. Go to Advanced > USB Sharing > 3G/4G Settings.
6. Verify that your 3G/4G USB Modem is successfully detected.
Note:
If your 3G/4G USB modem is incompatible with the modem router, it will not be identified. Find the 3G/4G Compatibility
List on the web page: http://www.tp-link.com/en/comp-list.html. If your USB modem is incompatible, contact our
technical support.
7. Verify that the modem router has correctly recognized your Mobile ISP. When your
Mobile ISP is correct, you can enjoy the internet! Otherwise, select the box Set the
Dial Number, APN, Username and Password manually and enter the information
provided by your 3G/4G network service provider.
8. Select the Connection Mode. The default mode is Always on. You can choose
Connect on demand or Connect manually.
46
Chapter 9 USB Settings
• If you choose Connect manually, you need to click the Connect or Disconnect
button to manually turn on or off the internet.
• If you choose Connect on demand, the network will automatically turn off when
there is no internet request in Max Idle Time, and turn on again when you try to
connect to the internet.
9. Click Advanced to have more configurations if needed.
10. Click Save to make the settings effective.
Chapter 10
Parental Controls
This function allows you to block inappropriate, explicit and malicious websites and
limit internet access during specified time periods.
48
Chapter 10 Parental Controls
I want to:
Control what types of websites my children or other home network users can visit and
the time of day they are allowed to access the internet.
For example, I want to allow my children’s devices (for example, a computer or a tablet)
to access only www.tp-link.com and wikipedia.org from 18:00 (6PM) to 22:00 (10PM) on
weekdays and not other time.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Basic or Advanced > Parental Controls and enable Parental Controls.
3. Click Add.
49
Chapter 10 Parental Controls
4. Click Scan, and add the device to be controlled. Or, enter the Device Name and
MAC Address manually.
5. Click the icon to set the Effective Time. Drag the cursor over the appropriate
cell(s) and click OK.
Note: The time of Parental Controls is based on the system time of the modem router. Please go to Advanced > System
Tools > Time Settings to set the correct time..
6. Enter a Description for the entry.
7. Select the check box to enable this entry and click OK.
8. Enable Content Restriction and select the restriction mode.
50
Chapter 10 Parental Controls
1 ) In Blacklist mode, the controlled devices cannot access any websites containing
the specified keywords during the Effective Time period.
2 ) In Whitelist mode, the controlled devices can only access websites containing
the specified keywords during the Effective Time period.
9. Click Add a New Keyword. You can add many keywords for both Blacklist and
Whitelist. Below are some sample entries to allow access.
1 ) Enter a web address (for example, www.tp-link.com) or a web address keyword
(for example, wikipedia) to only allow or block access to the websites containing
that keyword.
2 ) Specify the domain suffix (for example, .edu or .org) to allow access only to the
websites with that suffix.
10. Enter the keywords or websites you want to add and click Save.
Done!
Now you can control your children’s internet access according to your needs.
52
Chapter 11 QoS
11. 1. Prioritize Internet Traffic with QoS
QoS (Quality of Service) is designed to ensure the efficient operation of the network
when network congestion is encountered.
I want to:
Specify priority levels for some devices or applications.
For example, I have several devices that are connected to my wireless network. I would
like to set an intermediate speed on the internet for my phone.
How can I do that?
1. Enable QoS and set bandwidth allocation.
1 ) Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password
you set for the router.
2 ) Go to Advanced > QoS > Settings.
3 ) Select Enable QoS.
4 ) Choose your Line Type.
5 ) Input the maximum upload and download bandwidth provided by your internet
service provider. 1Mbps equals to 1000Kbps.
6 ) If you want to prioritize the IPTV traffic, select Enable, the IPTV Priority will be
high.
7 ) Click Advanced and drag the scroll bar to set the bandwidth priority percentage.
8 ) Click Save.
2. Add a middle priority QoS rule for the phone.
1 ) Click Add in the Middle Priority area and then select By Device and click Scan.
53
Chapter 11 QoS
2 ) Choose the respective device from the list.
3 ) Click Save.
3. Refer to the steps above to apply other QoS rules if any.
Note:
If you want to delete a QoS rule, click to remove the responding rule from the list.
Done!
Now QoS is implemented to prioritize internet traffic.
11. 2. Update the Database
This function can help to add or update the applications the router supports. If the
applications you need are not listed in the Application list, you can try to download
the new version and upgrade the database. New database versions are posted at
www.tp-link.com and can be downloaded for free.
1. Download the latest QoS database from our website (www.tp-link.com).
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
54
Chapter 11 QoS
3. Go to Advanced > QoS > Database. Click Browse to select the database upgrade file,
and then click Upgrade. Wait until the upgrade is complete and do not operate the
router during the process.
Chapter 12
Network Security
This chapter guides you on how to protect your home network from unauthorized users
by implementing these five network security functions. You can protect the router from
cyber attacks using the Firewall, prevent certain users from accessing the specified
service, and even block internet access completely using Service Filtering, or use
Access Control to block or allow specific client devices to access your network. Or
you can prevent ARP spoofing and ARP attacks by using IP & MAC Binding and you can
protect your IPv6 network by preventing access from the internet using IPv6 Firewall.
• Firewall & DoS Protection
• Service Filtering
• Access Control
• IP & MAC Binding
• IPv6 Firewall
56
Chapter 12 Network Security
12. 1. Firewall & DoS Protection
The SPI (Stateful Packet Inspection) Firewall and DoS (Denial of Service) Protection
protect the router from cyber attacks.
The SPI Firewall can prevent cyber attacks and validate the traffic that is passing
through the router based on the protocol. This function is enabled by default, and it’s
recommended to keep the default settings.
DoS Protection can protect your home network against DoS attacks from flooding your
network with server requests. Follow the steps below to configure DoS Protection.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > Firewall & DoS Protection.
3. Enable DoS Protection.
4. Set the level (Low, Middle or High) of protection for ICMP-Flood Attack Filtering,
UDP-Flood Attack Filtering and TCP-Flood Attack Filtering.
• ICMP-Flood Attack Filtering - Enable to prevent the ICMP (Internet Control
Message Protocol) flood attack.
• UDP-Flood Attack Filtering - Enable to prevent the UDP (User Datagram
Protocol) flood attack.
• TCP-Flood Attack Filtering - Enable to prevent the TCP (Transmission Control
Protocol) flood attack.
5. Click Save.
Tips:
1. The level of protection is based on the number of traffic packets. Specify the level at DoS Protection Level Settings.
57
Chapter 12 Network Security
2. The protection will be triggered immediately when the number of packets exceeds the preset threshold value, and
the vicious host will be displayed in the Blocked DoS Host List.
12. 2. Service Filtering
With Service Filtering, you can prevent certain users from accessing the specified
service, and even block internet access completely.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > Service Filtering.
3. Toggle on Service Filtering.
4. Click Add.
58
Chapter 12 Network Security
5. Select a Service Type from the drop-down list and the following four fields will be
auto-populated. Select Custom when your desired service type is not listed, and
enter the information manually.
6. Specify the IP address(es) that this filtering rule will apply to.
7. Click Save.
Note: If you want to disable this entry, click the icon.
12. 3. Access Control
Access Control is used to block or allow specific client devices to access your network
(via wired or wireless) based on a list of blocked devices (Blacklist) or a list of allowed
devices (Whitelist).
I want to:
Block or allow specific client devices to access my network (via wired or wireless).
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > Access Control and enable Access Control.
59
Chapter 12 Network Security
3. Select the access mode to either block (recommended) or allow the device(s) in the
list.
To block specific device(s)
1 ) Select Blacklist and click Save.
2 ) Select the device(s) to be blocked in the Online Devices table.
3 ) Click Block above the Online Devices table. The selected devices will be added
to Devices in Blacklist automatically.
To allow specific device(s)
1 ) Select Whitelist and click Save.
2 ) Click Add.
60
Chapter 12 Network Security
1 ) Click San and the Device Name and MAC Address will be automatically filled in.
Or enter the Device Name and MAC Address manually.
2 ) Click Save.
Done!
Now you can block or allow specific client devices to access your network (via wired or
wireless) using the Blacklist or Whitelist.
12. 4. IP & MAC Binding
IP & MAC Binding, namely, ARP (Address Resolution Protocol) Binding, is used to bind
a network device’s IP address to its MAC address. This will prevent ARP spoofing and
other ARP attacks by denying network access to a device with a matching IP address in
the Binding list, but an unrecognized MAC address.
I want to:
Prevent ARP spoofing and ARP attacks.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > IP & MAC Binding and enable IP & MAC Binding.
3. Bind your device(s) according to your needs.
61
Chapter 12 Network Security
To bind the connected device(s)
1 ) Select the device(s) to be bound in the ARP List.
2 ) Click Bind to add to the Binding List.
To bind the unconnected device
1 ) Click Add.
2 ) Enter the MAC Address and IP Address that you want to bind.
3 ) Select the check box to enable the entry and click OK.
Done!
Enjoy the internet without worrying about ARP spoofing and ARP attacks.
12. 5. IPv6 Firewall
IPv6 Firewall protects your IPv6 network by preventing access from the internet.
However, when you are hosting a service, such as a file sharing server in your local
network, you can choose to allow access to the server from the internet by adding
entries on this page. This feature is available only when you’ve set up an IPv6 connection.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Security > IPv6 Firewall.
3. Click Add.
62
Chapter 12 Network Security
4. Select an interface name from the drop-down list. Interface names are names of
the internet connections you have set up.
5. Click Scan to select a service from the list to automatically populate the Port field
with an appropriate port number. It is recommended to keep the default Port if you
are unsure about which one to use. If the service is not listed, manually enter the
Service Type and the Port number (e.g., 21 or 21-25).
6. Click Scan to select the local host device running the service. If the device is not
listed, enter its global IPv6 address in the Internal IP field
7. Select a protocol for the service from the drop-down list.
8. Tick Enable This Entry and click Save.
Note: If you want to disable this entry, click the icon.
Chapter 13
NAT Forwarding
Modem router’s NAT (Network Address Translation) feature makes the devices in the
LAN use the same public IP address to communicate in the internet, which protects the
local network by hiding IP addresses of the devices. However, it also brings about the
problem that external host cannot initiatively communicate with the specified device in
the local network.
The modem router can use a forwarding feature to remove the isolation of NAT and
allow external internet hosts to intuitively communicate with the devices in the local
network, thus enabling some special features.
TP-Link modem router includes four forwarding rules. If two or more rules are set, the
priority of implementation from high to low is Virtual Servers, Port Triggering, UPNP and
DMZ.
This chapter contains the following sections:
• Translate Address and Port by ALG
• Share Local Resources over the Internet by Virtual Server
• Open Ports Dynamically by Port Triggering
• Make Applications Free from Port Restriction by DMZ
• Make Xbox Online Games Run Smoothly by UPnP
64
Chapter 13 NAT Forwarding
13. 1. Translate Address and Port by ALG
ALG (Application Layer Gateway) allows customized NAT (Network Address Translation)
traversal filters to be plugged into the gateway to support address and port translation
for certain application layer “control/data” protocols: FTP, TFTP, H323 etc. Enabling ALG
is recommended.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > NAT Forwarding > ALG.
• PPTP Pass-through: If enabled, it allows Point-to-Point sessions to be tunneled
through an IP network and passed through the router.
• L2TP Pass-through: If enabled, it allows Layer 2 Point-to-Point sessions to be tunneled
through an IP network and passed through the router.
• IPSec Pass-through: If enabled, it allows IPSec (Internet Protocol Security) to
be tunneled through an IP network and passed through the router. IPSec uses
cryptographic security services to ensure private and secure communications over
IP networks.
• FTP ALG: If enabled, it allows FTP (File Transfer Protocol) clients and servers to transfer
data via NAT.
• TFTP ALG: If enabled, it allows TFTP (Trivial File Transfer Protocol) clients and servers
to transfer data via NAT.
• H323 ALG: If enabled, it allows Microsoft NetMeeting clients to communicate via NAT.
• SIP ALG: If enabled, it allows clients communicate with SIP (Session Initiation Protocol)
servers via NAT.
65
Chapter 13 NAT Forwarding
• RTSP ALG: If enabled, it allows RTSP (Real-Time Stream Protocol) clients and servers
to transfer data via NAT.
13. 2. Share Local Resources over the Internet by
Virtual Server
When you build up a server in the local network and want to share it on the internet,
Virtual Server can realize the service and provide it to the internet users. At the same
time virtual server can keep the local network safe as other services are still invisible
from the internet.
Virtual server can be used for setting up public services in your local network, such as
HTTP, FTP, DNS, POP3/SMTP and Telnet. Different service uses different service port.
Port 80 is used in HTTP service, port 21 in FTP service, port 25 in SMTP service and port
110 in POP3 service. Please verify the service port number before the configuration.
I want to:
Share my personal website I’ve built in a local network with my friends through the
internet.
For example, the personal website has been built on my home PC (192.168.1.100). I
hope that my friends can visit my website. The PC is connected to the modem router
with the WAN IP address 218.18.232.154.
Modem Router
WAN: 218.18.232.154
LAN
Home
Personal Website
How can I do that?
1. Assign a static IP address to your PC, for example 192.168.1.100.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
3. Go to Advanced > NAT Forwarding > Virtual Servers, click Add.
66
Chapter 13 NAT Forwarding
4. Click Scan, and choose HTTP. The external port, internal port and protocol will be
automatically filled with contents. Enter the PC’s IP address 192.168.1.100 in the
Internal IP field.
5. Click Save to save the settings.
Tips:
1. It is recommended to keep the default settings of Internal Port and Protocol if you are not clear about which port and
protocol to use.
2. If the service you want to use is not in the Service Type, you can enter the corresponding parameters manually. You
should verify the port number that the service needs.
3. You can add multiple virtual server rules if you want to provide several services from a modem router. Please note that
the External Port cannot be overlapped.
Done!
Internet users can enter http://WAN IP (in this example: http://218.18.232.154) to visit
your personal website.
Tips:
1. For a WAN IP that is assigned dynamically by ISP, it is recommended to apply and register a domain name for the
WAN by DDNS, go to Set Up a Dynamic DNS Service Account for more information. Then you can use http://domain
name to visit the website.
2. If you have changed the default External Port, you should use http://WAN IP: External Port or http://domain name:
External Port to visit the website.
13. 3. Open Ports Dynamically by Port Triggering
Port triggering can specify a triggering port and its corresponding external ports. When
a host in the local network initiates a connection to the triggering port, all the external
ports will be opened for subsequent connections. The modem router can record the IP
67
Chapter 13 NAT Forwarding
address of the host. When the data from the internet returns to the external ports, the
modem router can forward them to the corresponding host. Port triggering is mainly
applied to online games, VoIPs and video players. Common applications include MSN
Gaming Zone, Dialpad, Quick Time 4 players, and so on.
Follow the steps below to configure the port triggering rules:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > NAT Forwarding > Port Triggering and click Add.
3. Click Scan, and select the desired application. The triggering port and protocol, the
external port and protocol will be automatically filled with contents. Here we take
MSN Gaming Zone as an example.
4. Click Save to save the settings.
Tips:
1. You can add multiple port triggering rules according to your network need.
2. If the application you need is not listed in the Existing Applications list, please enter the parameters manually. You
should verify the external ports the application uses first and enter them into External Port field according to the
format the page displays.
13. 4. Make Applications Free from Port Restriction
by DMZ
When a PC is set to be a DMZ (Demilitarized Zone) host in the local network, it is totally
exposed to the internet, which can realize the unlimited bidirectional communication
68
Chapter 13 NAT Forwarding
between internal hosts and external hosts. The DMZ host becomes a virtual server with
all ports opened. When you are not clear about which ports to open in some special
applications, like IP camera and database software, you can set the PC to be a DMZ
host.
Note:
DMZ is most applicable when you don’t know which ports to open. When it is enabled, the DMZ host is totally exposed
to the internet, which may bring some potential safety hazard. If DMZ is not in use, please disable it in time.
I want to:
Make the home PC join the internet online game without port restriction.
For example, Due to some port restriction, when playing the online games, you can
login normally but cannot join a team with other players. To solve this problem, set your
PC as a DMZ with all ports opened.
How can I do that?
1. Assign a static IP address to your PC, for example 192.168.1.100.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
3. Go to Advanced > NAT Forwarding > DMZ and select the checkbox to enable DMZ.
4. Enter the IP address 192.168.1.100 in the DMZ Host IP Address filed.
5. Click Save to save the settings.
Done!
The configuration is completed. You’ve set your PC to a DMZ host and now you can
make a team to game with other players.
13. 5. Make Xbox Online Games Run Smoothly by
UPnP
UPnP (Universal Plug and Play) protocol allows the applications or host devices
to automatically find the front-end NAT device and send request to it to open the
corresponding ports. With UPnP enabled, the applications or host devices in the
both sides of NAT device can freely communicate with each other realizing the
69
Chapter 13 NAT Forwarding
seamless connection of the network. You may need to enable the UPnP if you want
to use applications such as multiplayer gaming, peer-to-peer connections, real-time
communication (for example, VoIP or telephone conference), or remote assistance.
Tips:
1. UPnP is enabled by default in this modem router.
2. Only the application supporting UPnP protocol can use this feature.
3. UPnP feature needs the support of operating system (e.g. Windows Vista/ Windows 7/ Windows 8, etc. Some of
operating system need to install the UPnP components).
For example, when you connect your Xbox to the modem router which has connected to
the internet to play online games, UPnP will send request to the modem router to open
the corresponding ports allowing the following data penetrating the NAT to transmit.
Therefore, you can play Xbox online games without a hitch.
Modem RouterXbox
LAN WAN
If necessary, you can follow the steps to change the status of UPnP.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router;
2. Go to Advanced > NAT Forwarding > UPnP and toggle on or off according to your
needs.
Chapter 14
VPN Server
The VPN (Virtual Private Networking) Server allows you to access your home network
in a secured way through the internet when you are out of the house. The router offers
three ways to setup VPN connection: OpenVPN, PPTP (Point to Point Tunneling Protocol)
VPN and IPSec (Internet Protocol Security) VPN.
OpenVPN is somewhat complex but with greater security and more stability. It is suitable
for restricted environment, such as campus network and company intranet.
PPTP VPN is easier to use and its speed is faster. It’s compatible with most operating
systems and also supports mobile devices. However, its security is poor and packets
may be cracked easily. PPTP VPN may be blocked by some ISPs.
IPSec (IP Security) is a set of services and protocols defined by IETF (Internet Engineering
Task Force) to provide high security for IP packets and prevent attacks.
This chapter contains the following sections, please choose the appropriate VPN server
connection type according to your needs.
• Use OpenVPN to Access Your Home Network
• Use PPTP VPN to Access Your Home Network
• Use IPSec VPN to Access Your Home Network
71
Chapter 14 VPN Server
14. 1. Use OpenVPN to Access Your Home Network
In an OpenVPN connection, the home network can act as a server, and the remote
device can access the server through the router which acts as an OpenVPN Server
gateway. To use the VPN feature, you should enable OpenVPN Server on your router,
install and run VPN client software on the remote device. Please follow the steps below
to set up an OpenVPN connection.
Step 1. Set up OpenVPN Server on Your Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Advanced > VPN > OpenVPN, and select Enable VPN Server.
Note:
• Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or
assign a static IP address for your router’s WAN port and synchronize your System Time via the internet.
• The first time you configure the OpenVPN Server, you may need to Generate a certificate before you
enable the VPN Server.
3. Select the Service Type (communication protocol) for OpenVPN Server: UDP, TCP.
4. Enter a VPN Service Port to which a VPN device connects. The port number should
be between 1024 and 65535.
5. In the VPN Subnet/Netmask fields, enter the range of IP addresses that can be leased
to the device by the OpenVPN server.
72
Chapter 14 VPN Server
6. Select your Client Access type. Select Home Network Only if you only want the
remote device to access your home network; select Internet and Home Network if
you also want the remote device to access the internet through the VPN Server.
7. Click Save.
8. Click Generate to get a new certificate.
Note:
If you have already generated one, please skip this step, or click Generate to update the certificate.
9. Click Export to save the OpenVPN configuration file which will be used by the remote
device to access your router.
Step 2. Configure OpenVPN Connection on Your Remote Device
1. Visit http://openvpn.net/index.php/download/community-downloads.html to
download the OpenVPN software, and install it on your device where you want to run
the OpenVPN client utility.
Note:
You need to install the OpenVPN client utility on each device that you want to be able to use the VPN function. Mobile
devices should download a third-party app from Google Play or Apple App Store.
2. After the installation, copy the file exported from your router to the OpenVPN client
utility’s “config” folder (for example, C:\Program Files\OpenVPN\config on Windows).
The path depends on where the OpenVPN client utility is installed.
3. Run the OpenVPN client utility and connect it to OpenVPN Server.
14. 2. Use PPTP VPN to Access Your Home Network
PPTP VPN Server is used to create a VPN connection for remote devices. To use the
VPN feature, you should enable PPTP VPN Server on your router, and configure the
PPTP connection on the remote device. Please follow the steps below to set up a PPTP
VPN connection.
Step 1. Set up PPTP VPN Server on Your Router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Advanced > VPN > PPTP VPN, and select Enable VPN Server.
73
Chapter 14 VPN Server
Note:
Before you enable VPN Server, we recommend you configure Dynamic DNS Service (recommended) or assign a static
IP address for router’s WAN port and synchronize your System Time with internet.
3. In the Client IP Address field, enter the range of IP addresses (up to 10) that can be
leased to the devices by the PPTP VPN server.
4. Enter the Username and Password to authenticate clients to the PPTP VPN server.
5. Click Save.
Step 2. Configure PPTP VPN Connection on Your Remote Device
The remote device can use the Windows built-in PPTP software or a third-party PPTP
software to connect to PPTP Server. Here we use the Windows built-in PPTP software
as an example.
1. Go to Start > Control Panel > Network and Internet > Network and Sharing Center.
2. Select Set up a new connection or network.
3. Select Connect to a workplace and click Next.
74
Chapter 14 VPN Server
4. Select Use my Internet connection (VPN).
5. Enter the internet IP address of the router (for example: 218.18.1.73) in the Internet
address field. Click Next.
75
Chapter 14 VPN Server
6. Enter the Username and Password you have set for the PPTP VPN server on your
router, and click Connect.
7. The PPTP VPN connection is created and ready to use.
76
Chapter 14 VPN Server
14. 3. Use IPSec VPN to Access Your Home Network
IPSec VPN is used to create a VPN connection between local and remote networks.
To use IPSec VPN, you should check that both local and remote routers support IPSec
VPN feature. Then, follow the steps below to set up an IPSec VPN connection.
1. The typical VPN topology is here. Site A refers to local network, and Site B refers to
the remote network that is to be connected. Record Site A and Site B’s LAN and WAN
IP addresses before you start configuration.
Modem router 1
LAN: 192.168.1.1
WAN: 219.134.112.246
PC 1
Subnetmask: 255.255.255.0
WAN: 219.134.112.247
Modem Router 2
PC 2
LAN: 192.168.2.1
Subnetmask: 255.255.255.0
Site A Site B
2. Configuration on Site A (local network).
1 ) Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password
you set for the router.
2 ) Go to Advanced > VPN > IPSec VPN, and click Add.
77
Chapter 14 VPN Server
3 ) In the IPSec Connection Name column, specify a name.
4 ) In the Remote IPSec Gateway (URL) column, Enter Site B’s WAN IP address.
5 ) Configure Site A’s LAN.
In the Tunnel access from local IP addresses column, we take Subnet Address
as an example. Input the LAN IP range of Site A in the IP Address for VPN column,
and input Subnet Mask of Site A.
6 ) Configure Site B’s LAN.
In the Tunnel access from remote IP addresses column, we take Subnet
Address as an example. Input the LAN IP range of Site B in the IP Address for
VPN column, and input Subnet Mask of Site B.
7 ) Select the Key Exchange Method for the policy. We select Auto(IKE) here.
78
Chapter 14 VPN Server
8 ) Enter the Pre-Shared Key for IKE authentication. Then keep Perfect Forward
Secrecy enabled.
Note: Make sure Site A and Site B use the same key.
9 ) Leave the Advanced Settings as default value. Then click Save.
Note: The Status column is Down after the configuration, and it will change to UP only when Site A and Site B are
communicating via the VPN connection.
3. Configuration on Site B (remote network). Refer to step 2 configuration on Site A
and make sure that Site A and Site B use the same pre-shared keys and Perfect
Forward Secrecy settings.
4. Check the VPN connection. You can ping site B’ LAN IP from your computer in site
A to verify that the IPSec VPN connection is set up correctly.
Tips: To check the VPN connection, you can do the following.
1. On the host in Site A, press [Windows Logo] + [R] to open Run dialog. Input “cmd” and hit OK.
2. In the CLI window, type in “ping 192.168.2.x” (“192.168.2.x” can be IP address of any host in Site B). Then press [Enter].
3. If Ping proceeds successfully (gets replies from host in Site B), the IPSec connection is working properly now.
5. Now IPSec VPN is implemented to establish a connection.
79
Chapter 14 VPN Server
Note:
1. The product supports a maximum of ten simultaneous connections.
2. If one of the site has been offline for a while, for example, if Site A has been disconnected, on Site B you need to click
Disable and then click Enable after Site A back on line in order to re-establish the IPSec tunnel.
Chapter 15
Specify Your Network
Settings
This chapter introduces how to change the default settings or adjust the basic
configuration of the modem router using the web management page.
It contains the following sections:
• LAN Settings
• IPv6 LAN Settings
• Wireless Settings
• Set Up a Dynamic DNS Service Account
• Create Static Routes
• Set Up the IPv6 Tunnel
81
Chapter 15 Specify Your Network Settings
15. 1. LAN Settings
15. 1. 1. Change the LAN IP Address
The modem router is preset with a default LAN IP 192.168.1.1, which you can use to log
in to its web management page. The LAN IP address together with the Subnet Mask
also defines the subnet that the connected devices are on. If the IP address conflicts
with another device in your local network or your network requires a specific IP subnet,
you can change it.
Follow the steps below to change your IP address.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings page and select IPv4.
Note:
If you have created an interface group, you can configure different IPv4 LAN settings for the default and created interface
groups.
3. Type in a new IP Address appropriate to your needs.
4. Select the Subnet Mask from the drop-down list. The subnet mask together with
the IP address identifies the local IP subnet.
5. Keep IGMP Snooping enabled by default. IGMP snooping is the process of listening
to IGMP (Internet Group Management Protocol) network traffic. The function
prevents hosts on a local network from receiving traffic for a multicast group they
have not explicitly joined.
6. You can configure the modem router’s Second IP and Subnet Mask for LAN interface
through which you can also access the web management page.
7. Leave the rest of the default settings as they are.
8. Click Save to make the settings effective.
82
Chapter 15 Specify Your Network Settings
15. 1. 2. Use the Modem Router as a DHCP Server
You can configure the modem router to act as a DHCP server to assign IP addresses to
its clients. To use the DHCP server function of the modem router, you must configure all
computers on the LAN to obtain an IP Address automatically.
Follow the steps below to configure DHCP server.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings page and select IPv4.
Note:
If you have created an interface group, you can configure different IPv4 LAN settings for the default and created interface
groups.
3. Select DHCP to enable the DHCP function and select DHCP Server.
4. Specify the IP Address Pool, the start address and end address must be on the
same subnet with LAN IP. The modem router will assign addresses within this
specified range to its clients. It is from 192.168.1.100 to 192.168.1.199 by default.
5. Enter a value for the Address Lease Time. The Address Lease Time is the amount of
time in which a DHCP client can lease its current dynamic IP address assigned by the
modem router. After the dynamic IP address expires, the user will be automatically
assigned a new dynamic IP address. The default is 1440 minutes.
6. Keep the rest of the settings as default and click Save.
Note:
1. The modem router can be configured to work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data
between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device’s
interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will be forwarded to
the DHCP server that runs on WAN side.
2. You can also appoint IP addresses within a specified range to devices of the same type by using Condition Pool
feature. For example, you can assign IP addresses within the range (192.168.1.50 to192.168.1.80) to Camera devices,
thus facilitating the network management. Enable DHCP feature and configure the parameters according to your
situation on the Advanced > Network > LAN Settings page.
83
Chapter 15 Specify Your Network Settings
15. 1. 3. Reserve LAN IP Addresses
You can view and add a reserved address for a client. When you specify an IP address
for a device on the LAN, that device will always receive the same IP address each time
when it accesses the DHCP server. If there are some devices in the LAN that require
permanent IP addresses, please configure Address Reservation on the router for the
purpose.
Follow the steps below to reserve an IP address for your device.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings page and select IPv4.
3. Scroll down to locate the Address Reservation table and click Add to add an address
reservation entry for your device.
4. Click Scan and select the device for which you want to reserve IP address. Then the
MAC Address and IP Address fields will be automatically filled in.
5. Specify the IP address which will be reserved by the router.
6. Check to Enable this entry and click Save to make the settings effective.
15. 2. IPv6 LAN Settings
Based on the IPv6 protocol, the modem router provides two ways to assign IPv6 LAN
addresses:
• Configure the RADVD (Router Advertisement Daemon) address type
• Configure the DHCPv6 Server address type
84
Chapter 15 Specify Your Network Settings
15. 2. 1. Configure the RADVD Address Type
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings.
3. Select IPv6 to configure IPv6 LAN parameters.
Note:
If you have created an interface group, you can configure IPv6 LAN settings for the default interface group only.
1 ) Select the RADVD address type to make the modem router assign IPv6 address
prefixes to hosts.
Note:
Do not select the Enable RDNSS and Enable ULA Prefix check boxes unless required by your ISP. Otherwise
you may not be able to access the IPv6 network. For more information about RDNSS and ULA Prefix, contact
our technical support.
2 ) Keep Site Prefix Type as the default value Delegated. If your ISP has provided a
specific IPv6 site prefix, select Static and enter the prefix.
3 ) Keep WAN Connection as the default value.
4. Click Save to make the settings effective.
15. 2. 2. Configure the DHCPv6 Server Address Type
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > LAN Settings.
3. Select IPv6 to configure IPv6 LAN parameters.
85
Chapter 15 Specify Your Network Settings
Note:
If you have created an interface group, you can configure IPv6 LAN settings for the default interface group only.
1 ) Select the DHCPv6 Server address type to make the modem router assign
IPv6 addresses to hosts.
2 ) Specify the Starting/Ending IPv6 Address for the IPv6 suffixes. The modem
router will generate IPv6 addresses within the specified range.
3 ) Keep Address Lease Time as the default value.
4 ) Keep Site Prefix Type as the default value Delegated. If your ISP has provided a
specific IPv6 site prefix, select Static and enter the prefix.
5 ) Keep WAN Connection as the default value.
4. Click Save to make the settings effective.
15. 3. Wireless Settings
15. 3. 1. Specify Basic Wireless Settings
The modem router’s wireless network name (SSID) and password, and security option
are preset in the factory. The preset SSID and password can be found on the product
label. You can customize the wireless settings according to your needs.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Basic > Wireless page.
86
Chapter 15 Specify Your Network Settings
• To enable or disable the wireless function:
Enable the 2.4 GHz or 5GHz Wireless Network. If you don’t want to use the wireless
function, just deselect the box. If you disable the wireless function, all the wireless
settings won’t be effective.
• To change the wireless network name (SSID) and wireless password:
Enter a new SSID using up to 32 characters. The value is case-sensitive.
Note:
If you use a wireless device to change the wireless settings, you will be disconnected after the new settings are effective.
Please write down the new SSID and password for future use.
• To hide SSID:
Select Hide SSID, and your SSID will not be broadcast. Your SSID won’t display on your
wireless device when you scan for local wireless network list and you need to manually
join the network.
• To use the Smart Connect function:
The smart connect function lets you to enjoy a more high-speed network by assigning
your devices to best wireless bands based on actual conditions to balance network
demands.
1. Go to Advanced > Wireless > Wireless Settings.
2. Enable Smart Connect.
3. Keep the default or set a new SSID and password, and click Save. This SSID and
password will be applied both for 2.4GHz and 5GHz wireless networks.
87
Chapter 15 Specify Your Network Settings
• To change the mode or channel:
Go to Advanced > Wireless > Wireless Settings page and select the wireless network
2.4GHz or 5GHz.
Mode: Select the desired mode.
• 802.11n only: Select only if all of your wireless clients are 802.11n devices.
• 802.11gn mixed: Select if you are using both 802.11g and 802.11n wireless clients.
• 802.11bgn mixed: Select if you are using a mix of 802.11b, 11g, and 11n wireless
clients.
Note: When 802.11n only mode is selected, only 802.11n wireless stations can connect to the modem router. It is
strongly recommended that you select 802.11bgn mixed, and all of 802.11b, 802.11g, and 802.11n wireless stations
can connect to the modem router.
• 802.11ac/n mixed (5GHz): Select if you are using both 802.11ac and 802.11n wireless
clients.
• 802.11a/n/ac mixed (5GHz): Select if you are using a mix of 802.11a, 802.11n and
802.11ac wireless clients. It is strongly recommended that you select 11a/n/ac mixed.
Channel: Select the channel you want to use from the drop-down list. This field
determines which operating frequency will be used. It is not necessary to change the
wireless channel unless you notice interference problems with another nearby access
point.
88
Chapter 15 Specify Your Network Settings
Channel Width: Select the channel width from the drop-down list. The default setting is
Auto, which can adjust the channel width for your clients automatically.
Transmit Power: Select Low, Middle, or High to specify the data transmit power. The
default and recommended setting is High.
• To change the security option:
1. Go to Advanced > Wireless > Wireless Settings page.
2. Select the wireless network 2.4GHz or 5GHz.
3. Select an option from the Security drop-down list. The router provides four options,
None, WPA/WPA2 Personal (Recommended), WPA/WPA2 Enterprise, WEP. WPA2
uses the newest standard and the security level is the highest. We recommend you
don’t change the default settings unless necessary.
15. 3. 2. Use WPS for Wireless Connection
You can use WPS (Wi-Fi Protected Setup) to add a new wireless device to your existing
network quickly and easily.
Method 1: Use the WPS button
Use this method if your client device has a WPS button.
1. Press the WPS button the modem router for 1 second.
2. Press the WPS button of the client device directly.
3. The WPS LED flashes for about 2 minutes during the WPS process.
4. When the WPS LED is on, the client device has successfully connected to the
modem router.
Method 2: Use the WPS button on the web management page
Use this method if your client device has a WPS button.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Wireless > WPS page.
3. Click Start WPS on the page.
89
Chapter 15 Specify Your Network Settings
4. Press the WPS button of the client device directly.
5. The WPS LED of the router flashes for about 2 minutes during the WPS process.
6. When the WPS LED is on, the client device has successfully connected to the
modem router.
Method 3: Enter the modem router’s PIN on your client device
Use this method if your client device asks for the modem router’s PIN.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Wireless > WPS page. Click Method Two--PIN.
3. Take a note of the Current PIN of the modem router. You can also click the Generate
button to get a new PIN.
4. On the client device, enter the modem router’s PIN. (The default PIN is also printed
on the label of the modem router.)
5. The WPS LED flashes for about two minutes during the WPS process.
6. When the WPS LED is on, the client device has successfully connected to the
modem router.
Note:
1. The WPS LED on the modem router will light on for five minutes if the device has been successfully added to the
network.
2. The WPS function cannot be configured if the wireless function of the modem router is disabled. Please make sure
the wireless function is enabled before configuring WPS.
Method 4: Enter the client device’s PIN on the modem router
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Wireless > WPS page. Click Method Two--PIN.
90
Chapter 15 Specify Your Network Settings
3. Select Client’s PIN.
4. Enter the client device’s PIN in the field. Then click the Connect button.
5. Device has been added successfully! will appear on the above screen, which means
the client device has successfully connected to the modem router.
15. 3. 3. Schedule Your Wireless Function
You can automatically turn off your wireless network (both 2.4GHz and 5GHz) when you
do not need the wireless connection.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Wireless > Wireless Schedule page.
3. Toggle on the button to enable the Wireless Schedule feature.
4. Click Add to set the Wireless Off Time, and click Save to save the settings.
5. Repeat steps 3 and 4 to set another entry.
Note:
1. Make sure that the time of the router is correct before using this function. For details, refer to Set System Time.
2. If you just set time for one wireless band, the other wireless band is still always on, so set time for both of the two
bands to schedule your whole wireless network.
3. The wireless LED (2.4GHz , 5GHz) will turn off if the corresponding wireless network is disabled.
4. The wireless network will be automatically turned on after the time period you set.
91
Chapter 15 Specify Your Network Settings
15. 3. 4. View Wireless Information
• To view the detailed wireless network settings:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Status page. You can see the Wireless box.
3. Select 2.4GHz or 5GHz to view the wireless details.
Tips: You can also see the wireless details by clicking the router icon on Basic> Network Map.
• To view the detailed information of the connected wireless clients:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Wireless > Statistics page.
3. You can view the detailed information of the wireless clients, including its connected
wireless band and security option as well as the packets transmitted.
Tips: You can also see the wireless details by clicking the wireless clients icon on Basic > Network Map.
15. 3. 5. Advanced Wireless Settings
Advanced wireless settings are for those who have a network concept. If you are not
familiar with the settings on this page, it’s strongly recommended that you keep the
provided default values; otherwise it may result in lower wireless network performance.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Wireless > Advanced Settings page.
92
Chapter 15 Specify Your Network Settings
• Beacon Interval: Enter a value between 25 and 1000 in milliseconds to determine the
duration between which beacon packets are broadcasted by the router to synchronize
the wireless network. The default is 100 milliseconds.
• RTS Threshold: Enter a value between 1 and 2346 to determine the packet size of
data transmission through the router. By default, the RTS (Request to Send) Threshold
size is 2346. If the packet size is greater than the preset threshold, the router sends
Request to Send frames to a particular receiving station and negotiates the sending
of a data frame, or else the packet will be sent immediately.
• DTIM Interval: Enter a value between 1 and 255 to determine the interval of the
Delivery Traffic Indication Message (DTIM). 1 indicates the DTIM Interval is the same
as Beacon Interval.
• Group Key Update Period: Enter the number of seconds to control the time interval
for the encryption key automatic renewal. The default is 0, indicating no key renewal.
• WMM: This feature guarantees the packets with high-priority messages being
transmitted preferentially. WMM is enabled compulsively under 802.11n or 802.11ac
mode.
• Short GI: This feature is enabled by default and recommended to increase the data
capacity by reducing the Guard Interval (GI) time.
• AP Isolation: Select this check box to enable the AP Isolation feature that allows you
to confine and restrict all wireless devices on your network from interacting with each
other, but still able to access the internet. AP isolation is disabled by default.
15. 4. Set Up a Dynamic DNS Service Account
Most ISPs (Internet service providers) assign a dynamic IP address to the router and
you can use this IP address to access your router remotely. However, the IP address
can change any time and you don’t know when it changes. In this case, you might need
93
Chapter 15 Specify Your Network Settings
the DDNS (Dynamic Domain Name Server) feature on the router to allow you and your
friends to access your router and local servers (FTP, HTTP, etc.) using domain name, in
no need of checking and remembering the IP address.
Note: DDNS does not work if the ISP assigns a private WAN IP address (such as 192.168.1.x) to the modem router.
To set up DDNS, please follow the instructions below:
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > Dynamic DNS.
3. Select the DDNS service provider (TP-Link, Dyndns or NO-IP).
4. To use TP-Link DDNS service, you should log in with your TP-Link ID.
5. If you choose other DDNS service, you should also log in with your DDNS account,
select a service provider and click Go to register ... Enter the username, password
and domain name of the account (such as lisa.ddns.net).
6. Click Log in and Save.
Tips: If you want to use a new DDNS account, please Logout first, then login with the new account.
15. 5. Create Static Routes
A static route is a pre-determined path that network information must travel to reach
a specific host or network. Data from one point to another will always follow the same
path regardless of other considerations. Normal internet usage does not require this
setting to be configured.
I want to:
Visit multiple networks and multiple servers at the same time.
For example, in a small office, my PC can surf the internet, but I also want to visit my
company’s server. Now I have a switch and another router. I connect the devices as
94
Chapter 15 Specify Your Network Settings
shown in the following figure so that the physical connection between my PC and my
company’s server is achieved. To surf the internet and visit my company’s network at
the same time, I need to configure the static routing.
Company’s server
My PC
Router 2
Modem router
Switch
LAN: 192.168.1.1
192.168.1.100
LAN: 192.168.1.2
WAN: 172.30.30.100
172.30.30.1
How can I do that?
1. Make sure the routers use different LAN IP addresses on the same subnet. Disable
Router 2’s DHCP function.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
3. Go to Advanced > Network > Static Routing. Select your current WAN Interface and
click Save.
4. Click Add to add a new static routing entry. Finish the settings according to the
following explanations:
95
Chapter 15 Specify Your Network Settings
• Network Destination: The destination IP address that you want to assign to a
static route. This IP address cannot be on the same subnet with the WAN IP or
LAN IP of the router. In the example, the IP address of the company network is
the destination IP address, so here enters 172.30.30.1.
• Subnet Mask: Determines the destination network with the destination IP
address. If the destination is a single IP address, enter 255.255.255.255;
otherwise, enter the subnet mask of the corresponding network IP. In the
example, the destination network is a single IP, so here enters 255.255.255.255.
• Gateway: The IP address of the gateway device to which the data packets
will be sent. This IP address must be on the same subnet with the router’s IP
which sends out the data. In the example, the data packets will be sent to the
LAN port of Router 2 and then to the Server, so the default gateway should be
192.168.1.2.
• Interface: Determined by the port (WAN/LAN) that sends out the data packets.
In the example, the data is sent to the gateway through the LAN port, so LAN
should be selected.
5. Select the check box to enable this entry.
6. Click Save to save the settings.
Done!
Open a web browser on your PC. Enter the company server’s IP address to visit the
company network.
15. 6. Set Up the IPv6 Tunnel
The IPv6 Tunnel feature helps you obtain IPv6 resources based on an IPv4 WAN
connection or vice versa.
96
Chapter 15 Specify Your Network Settings
IPv6 Tunnel is a transition mechanism that allows isolated IPv6 hosts and networks to
reach each other over IPv4-only infrastructure before IPv6 completely supplants IPv4.
It is a temporary solution for networks that do not support native dual-stack, where
both IPv6 and IPv4 run independently.
The modem router provides three tunneling mechanisms: 6to4, 6rd and DS-Lite. The
way to set up 6rd and DS-Lite tunnel are similar.
15. 6. 1. Use the Public IPv6 Tunnel Service-6to4
The 6to4 tunnel is a kind of public service. If there are any 6to4 servers on your network,
you can use this mechanism to access IPv6 service. If your ISP provides you with an
IPv4-only connection but you want to visit IPv6 websites, you can try to set up a 6to4
tunnel.
I want to:
Set up the IPv6 tunnel though my ISP doesn’t provide me with the tunnel service.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > IPv6 Tunnel.
3. Tick the check box, select 6to4 as the tunneling mechanism and select a WAN
connection from the drop-down list, then click Save.
Note:
If there is no available WAN connection to choose, make sure you have connected to the internet and the connection
type is not Bridge.
Done!
Now you can visit the IPv6 websites with the 6to4 tunnel.
Note:
Still not being able to access IPv6 resources means that not any 6to4 public server was found in your network. You can
contact your ISP to sign up for IPv6 connection service.
97
Chapter 15 Specify Your Network Settings
15. 6. 2. Specify the 6rd Tunnel with Parameters Provided by Your ISP
I want to:
Specify the 6rd tunnel with the parameters provided by my 6rd tunnel service provider.
How can I do that?
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > Network > IPv6 Tunnel.
3. Tick the check box, select 6rd as the tunneling mechanism and select a WAN
connection from the drop-down list.
4. According to the parameters provided by your ISP, choose Auto or Manual. More
parameters are needed if you choose Manual.
5. Click Save.
Note:
If there is no available WAN connection to choose, make sure you have connected to the internet and the connection
type is not Bridge.
Done!
Now you can visit the IPv6 websites with the 6rd tunnel.
Tips:
The way to set up DS-Lite tunnel is similar to that of 6rd tunnel. If you are provided with an IPv6-only WAN connection
and have signed up for DS-Lite tunnel service, specify the DS-Lite tunnel by referring to the steps above.
Chapter 16
Administrate Your Network
This chapter introduces how to change the system settings and administrate your
modem router’s network.
This chapter contains the following sections:
• Set System Time
• Control LEDs
• Update the Firmware
• Back up and Restore Configuration Settings
• Reboot the Modem Router
• Change the Administrator Account
• Local Management
• Remote Management
• System Log
• Monitor the Internet Traffic Statistics
• CWMP Settings
• SNMP Settings
99
Chapter 16 Administrate Your Network
16. 1. Set System Time
System time is the time displayed while the modem router is running. The system time
you configure here will be used for other time-based functions like Parental Controls
and Wireless Schedule. You can manually set how to get the system time.
Follow the steps below to set your system time.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
2. Go to Advanced > System Tools > Time Settings page.
3. Configure the system time using the following methods:
Manually: Select your time zone and enter your local time.
Get from PC: Click this button if you want to use the current managing PC’s time.
Get from the Internet: Click this button if you want to get time from the internet.
Make sure your modem router can access the internet before you select this way
to get system time.
4. Click Save.
5. After setting the system time, you can set Daylight Saving Time according to your
needs. Tick the check box to enable Daylight Saving Time, set the start and end
time and then click Save to make the settings effective.
100
Chapter 16 Administrate Your Network
16. 2. Control LEDs
The router‘s LEDs indicate router’s activities and status. You can turn on or turn off the
LEDs either from the web management page or by pressing the LED button.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. Go to Advanced > System Tools > LED Control.
• To turn on/off LEDs
Toggle on or off the LED Status to turn on or off the LEDs.
• To set up Night Mode
1. Enable Night Mode.
2. Specify a time period in the Night Mode Period as needed.
3. Click Save, and then the LEDs will be off during this period.
101
Chapter 16 Administrate Your Network
16. 3. Update the Firmware
TP-Link is dedicated to improving product features, giving you a better network
experience.
We will inform you through the web management page if there’s any update firmware
available for your router. The latest firmware can also be downloaded from the Support
page of our website www.tp-link.com for free.
Note:
1. Make sure that you have a stable connection between the router and your computer. It is NOT recommended to
upgrade the firmware wirelessly.
2. Make sure you remove any USB storage device connected to the router before the firmware upgrade to prevent data
loss.
3. Back up your router configuration before upgrading the firmware.
4. Do NOT turn off the router during the firmware upgrade.
16. 3. 1. Online Upgrade
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
2. If there’s any firmware update available for your router, the update icon will display
on the top-right corner of the page. Click the icon to go to the Firmware Upgrade
page.
Alternatively, you can go to Advanced > System Tools > Firmware Upgrade,
and click Check for Upgrades to see if there’s any new firmware.
Tips:
If there’s any new important firmware update for your router, you will see the notification (similar as shown below)
on your computer when open a new web page. Click Upgrade now, and log into the web management page. You
will see the Firmware Upgrade page.
3. Wait a few moments for the upgrading and rebooting.
102
Chapter 16 Administrate Your Network
16. 3. 2. Local Upgrade
1. Download the latest firmware file for the router from our website www.tp-link.com.
2. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you set
for the router.
3. Go to Advanced > System Tools > Firmware Upgrade.
4. Focus on the Device Information section. Make sure the downloaded firmware file
matches with the Hardware Version.
5. Focus on the Local Upgrade section. Click Browse to locate the downloaded new
firmware file, and click Upgrade.
6. Wait a few moments for the upgrading and rebooting.
16. 4. Back up and Restore Configuration Settings
The configuration settings are stored as a configuration file in the router. You can back
up the configuration file to your computer for future use and restore the modem router
to a previous settings from the backup file when needed. Moreover, if needed you can
erase the current settings and reset the modem router to the default factory settings.
• To back up configuration settings
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Click Advanced > System Tools > Backup & Restore page.
3. Click Backup to save a copy of the current settings to your local computer. A conf.
bin file will be stored to your computer.
• To restore configuration settings
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Click Advanced > System Tools > Backup & Restore page.
103
Chapter 16 Administrate Your Network
3. Click Browse to locate the previous backup configuration file, and click Restore.
4. Wait for the restoring and then the modem router will automatically reboot.
• To reset the modem router to factory default settings
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Click Advanced > System Tools > Backup & Restore page.
3. Click Restore to restore all configuration settings to default values, except your
login and TP-Link ID information. Click Factory Restore to reset the modem router.
4. Wait for the reset process to complete, and then the modem router will automatically
reboot.
Note:
1. During the resetting process, do not turn off the modem router.
2. We strongly recommend you back up the current configuration settings before resetting the modem router.
16. 5. Reboot the Modem Router
The Reboot feature cleans the cache to enhance the running performance of the router.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > System Tools > Reboot.
• To Reboot Manually
Locate the Manual Reboot section and click Reboot.
• To Reboot Automatically
1. Locate the Reboot Schedule section and check the box to enable Reboot Schedule.
104
Chapter 16 Administrate Your Network
2. Specify the Reboot Time when the router reboots and Repeat to decide how often
it reboots.
Note:
Before enabling Reboot Schedule, please make sure your router is connected to the internet, then go to Advanced >
System Tools > Time Settings and choose Get from the Internet to get the correct network time.
3. Click Save.
16. 6. Change the Administrator Account
Admin account is used to log in to the modem router’s web management page. You are
required to set the admin account at first login. You can also change it on the web page.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > System Tools > Administration page. Locate the Account
Management section.
3. Enter the old password. Enter the new password and enter again to confirm.
4. Click Save to make the settings effective.
105
Chapter 16 Administrate Your Network
16. 7. Local Management
You can control the local devices’ authority to manage the modem router via Local
Management feature. By default all local connected devices are allowed to manage
the modem router. You can also specify one device to manage the modem router and
enable local management over a more secure way, HTTPS.
Follow the steps below to allow only the specific device to manage the router via the
local management over HTTPS.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > System Tools > Administration page. Locate the Local
Management section.
3. Keep the Port as the default setting. Enable Management over HTTPS and keep the
Port for HTTPS as the default setting. Enter the IP address or MAC address of the
local device to manage the modem router.
4. Click Save.
Now, you can manage the modem router over both HTTP (http://tplinkmodem.net) and
HTTPS (https://tplinkmodem.net).
Note:
If you want that all local devices can manage the modem router, just leave the IP/MAC Address field blank.
16. 8. Remote Management
By default, the remote devices are not allowed to manage the modem router from the
internet. You can enable remote management over HTTP and/or HTTPS if needed.
HTTPS is a more secure way to access the router.
Note:
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), you cannot use the remote management
feature because private addresses are not routed on the internet.
Follow the steps below to allow remote devices to manage the modem router over
HTTPS.
106
Chapter 16 Administrate Your Network
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > System Tools > Administration page. Locate the Remote
Management section.
3. Tick the check box to enable Remote Management. Enable Remote Management
via HTTPS to allow for HTTPS connection. Keep the Port as the default setting.
4. Set the client device allowed for remote management. Select All to allow all remote
devices to manage the modem router. If you just want to allow a specific device to
manage the modem router, select Only the Following IP Address and enter the IP
address of the remote device.
5. Click Save.
All devices or the specific device on the internet can log in to your router using the
address displayed on the Manage This Router via the Address field to manage the
modem router.
Tips:
1. If you were warned about the certificate when visiting the web management page remotely, click Trust (or a similar
option) to continue. To avoid this warning, you can download and install the certificate on the modem router’s web
management page at Advanced > System Tools > Administration.
2. The router’s WAN IP is usually a dynamic IP. Please refer to Set Up a Dynamic DNS Service Account if you want to log
in to the router through a domain name.
107
Chapter 16 Administrate Your Network
16. 9. System Log
System Log can help you know what happened to your modem router, facilitating
you to locate the malfunctions. For example when your modem router does not work
properly, you will need to save the system log and send it to the technical support for
troubleshooting.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Click Advanced > System Tools > System Log page.
• To view the system logs:
You can view specific system logs by selecting the log Type and Level.
Click Refresh to refresh the log list.
• To save the system logs:
You can choose to save the system logs to your local computer or a remote server.
Click Save Log to save the logs in a txt file to your computer.
Click Log Settings to set the storage path of logs.
108
Chapter 16 Administrate Your Network
• Save Locally: Select this option to cache the system log to the router’s local memory,
select the minimum level of system log to be saved from the drop-down list. The logs
will be shown in the table in descending order on the System Log page.
• Save Remotely: Select this option to send the system log to a remote server, select
the minimum level of system log to be saved from the drop-down list and enter the
information of the remote server. If the remote server has a log viewer client or a sniffer
tool implemented, you can view and analyze the system log remotely in real-time.
16. 10. Monitor the Internet Traffic Statistics
The Traffic Statistics page displays the network traffic of the interfaces, including the
received and sent packets.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > System Tools > Traffic Monitor.
3. Toggle on Traffic Monitor, select the desired interface from the dropdown list, and
then you can see the packets received and sent via this interface in the past ten
minutes. This function is disabled by default.
109
Chapter 16 Administrate Your Network
4. You can also go to Traffic Monitor List to view the traffic usage of all interfaces.
16. 11. CWMP Settings
The modem router supports CWMP (CPE WAN Management Protocol), also called
TR-069. This collects information, performs diagnostics and configures the devices
automatically via ACS (Auto-Configuration Server).
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the router.
2. Go to Advanced > System Tools > CWMP Settings page.
110
Chapter 16 Administrate Your Network
• CWMP: Toggle On to enable the CWMP (CPE WAN Management Protocol) feature.
• Inform: Enable this feature to send an Inform message to the ACS (Auto Configuration
Server) periodically.
• Inform Interval: Enter the time interval in seconds when the Inform message will be
sent to the ACS.
• ACS URL: Enter the web address of the ACS which is provided by your ISP.
• ACS Username/Password: Enter the username/password to log in to the ACS server.
• Interface used by TR-069 client: Select which interface to be used by the TR-069
client.
• Display SOAP messages on serial console: Toggle to enable or disable this feature.
• Connection Request Authentication: Select this check box to enable authentication
for the connection request.
• Username/Password: Enter the username/password for the ACS server to log in to
the router.
• Path: Enter the path for the ACS server to log in to the router.
• Port: Enter the port that connects to the ACS server.
• URL: Enter the URL that connects to the ACS server.
111
Chapter 16 Administrate Your Network
• Get RPC methods: Click to get the methods to support CWMP.
Click Save to make the settings effective.
16. 12. SNMP Settings
SNMP (Simple Network Management Protocol) is widely applied in the computer
networks of today, and is used for ensuring the transmission of the management
information between two nodes. In this way, network administrators can easily search
and modify the information on any node on the network. Meanwhile, they can locate
faults promptly and implement the fault diagnosis, capacity planning and report
generating.
An SNMP Agent is an application running on the modem router that performs the
operational role of receiving and processing SNMP messages, sending responses to
the SNMP manager, and sending traps when an event occurs. So a router contains
SNMP “agent” software can be monitored and/or controlled by SNMP Manager using
SNMP messages.
1. Visit http://tplinkmodem.net, and log in with your TP-Link ID or the password you
set for the modem router.
2. Go to Advanced > System Tools > SNMP Settings page.
• SNMP Agent: Toggle On to enable the built-in SNMP agent that allows the router
to operate as the operational role in receiving and processing of SNMP messages,
sending responses to the SNMP manager, and triggering SNMP traps when an event
occurs.
112
Chapter 16 Administrate Your Network
• SNMP Agent for WAN: Toggle On to allow management from the WAN side using
SNMP.
• Read-only Community: Displays the default public community string that protects the
router from unauthorized access.
• Write Community: Displays the default write community string that protects the router
from unauthorized changes.
• System Name: Displays the administratively-assigned name for this managed device.
• System Description: Displays the textual description of the managed device. This
value should include the full name and version identification of the system’s hardware
type, software operating-system, and networking software.
• System Location: Displays the physical location of this device (for example, the
telephone closet, 3rd floor).
• System Contact: Displays the textual identification of the contact person for this
managed device, together with information on how to contact this person.
• Trap Manager IP: Displays the IP address of the host to receive the traps.
You are suggested to keep the default settings. Click Save to make the settings effective.
113
Appendix: Troubleshooting
T1. How do I restore my modem router’s configuration to its factory
default settings?
With the modem router powered on, press and hold down the Reset button on the
modem router for 8 seconds until all LEDs turn on momentarily, then release the button.
Note: Once the modem router is reset, the current configuration settings will be lost and you will need to re-configure
the modem router.
T2. What should I do if I forgot my password?
Web management page password:
• If you are using a TP-Link ID to log in, click Forgot password on the login page and
then follow the instructions to reset the password.
• Alternatively, refer to T1 to reset the router, and then visit http://tplinkmodem.net to
create a new login password.
Wireless network password:
1. The default Wireless Password/PIN is printed on the product label of the modem
router.
2. If the default wireless password has been changed, log in to the modem router’s web
management page and go to Basic > Wireless to retrieve or reset your password.
T3. What should I do if I cannot log in to the modem router’s web
management page?
• Make sure the modem router connects to the computer correctly and the
corresponding LED indicator(s) light up.
• Make sure the IP address of your computer is configured to obtain an IP address
automatically and obtain the DNS server address automatically.
• Make sure the default access you input is right.
• Check your computer’s settings:
1 ) Go to Start > Control Panel > Network and Internet, and click View network
status and tasks;
2 ) Click Internet Options on the bottom left;
3 ) Click Connections, select Never dial a connection;
114
4 ) Click LAN settings, deselect the following three options and click OK;
5 ) Go to Advanced > Restore advanced settings, click OK to save the settings.
115
• Change a web browser or computer and log in again.
• Reset the modem router to factory default settings. Refer to Back up and Restore
Configuration Settings for detailed information. Open a web browser and log in
again. If login fails, please contact our Technical Support.
T4. What should I do if I cannot access the internet?
1. Ensure all connections are secure, including telephone lines, Ethernet cables and
power adapters.
2. Check to see if you can log in to the web management page of the modem router.
If you cannot, please adjust your computer’s settings according to T3 and then see
if you can access the internet. If the problem persists, please go to the next step.
3. Consult your ISP and make sure the VPI/VCI, Connection Type, account username
and password are correct. If there are any mistakes, please correct the settings and
try again.
4. Refer to T5 to clone the MAC address.
5. If you still cannot access the internet, please restore your modem router to its
factory default settings and reconfigure your modem router by following the
instructions in Use Quick Setup Wizard.
116
6. Please contact our Technical Support if the problem persists.
T5. How do I clone a MAC address?
You can manually change the MAC address of the modem router. It is helpful when your
internet access account provided by your ISP is bound to one specific MAC address,
in other words, your ISP just permits only one computer with the authenticated MAC
address to access the internet. In this case, you can use MAC Clone to allow more
computers to access the internet via the same account.
1. Visit http://tplinkmodem.net, and log in with the account you set for the modem
router.
2. Go to Advanced > Network > Internet page. Click the Add icon, and scroll down to
get the MAC Clone section.
• If you are using the computer with the authenticated MAC address to access
the modem router, please select Use Current Computer MAC Address.
• If you know the authenticated MAC address, please select Use Custom MAC
Address and then enter the address.
3. Click OK to make the settings effective.
T6. How can I change my computer‘s settings to obtain an IP address
automatically?
To change the computer’s network settings, follow the steps below.
• For MAC OS X:
1 ) Click the Apple icon, and select System Preferences from the drop-down list.
2 ) Click the Network icon.
3 ) Select Ethernet (for wired connection) or Wi-Fi (for wireless connection) in the
left panel, then click Advanced.
4 ) Click TCP/IP.
5 ) From the Configure IPv4 drop-down list, select Using DHCP.
117
6 ) Click OK.
• For Windows 7/8/8.1/10:
1 ) Right-click the Network icon on the system tray and select Open Network and
Sharing Center > Change adapter settings.
2 ) Right-click your network connection (wired or wireless) and select Properties.
3 ) Double-click Internet Protocol Version 4 (TCP/IPv4).
4 ) Select both Obtain an IP address automatically and Obtain DNS server address
automatically, then click OK.
5 ) Click OK again to save your configuration.
• For Windows XP:
1 ) Right-click the Network icon on the system tray and select Open Network
Connections.
2 ) Right-click your network connection (wired or wireless) and select Properties.
3 ) Double-click Internet Protocol (TCP/IP).
4 ) Select both Obtain an IP address automatically and Obtain DNS server address
automatically, then click OK.
5 ) Click OK again to save your configuration.
T7. What should I do if I cannot find my wireless network or I cannot
connect the wireless network?
• If you fail to find any wireless network, follow the steps below:
1. Make sure the wireless function is enabled if you’re using a laptop with built-in
wireless adapter. You can refer to the relevant document or contact the laptop
manufacturer.
2. Make sure the wireless adapter driver is installed successfully and the wireless
adapter is enabled. You can refer to the relevant document or contact the wireless
adapter manufacturer.
• If you can find other wireless network except your own, follow the steps below:
1. Check the Wi-Fi LED indicator on your wireless router/modem;
2. Make sure your computer/device is still in range of your router/modem. Move closer
if you are currently too far away.
3. Go to Basic > Wireless page, and check the wireless settings, double-check your
Wireless Name (SSID) is not hidden.
4. Connect to wireless network.
118
• If you can find your wireless network but fail to connect, follow the steps below:
1. Authentication problem: Network Security Key Mismatch.
1 ) Sometimes you will be asked to type in a PIN number when you connect to
the wireless network for the first time. This PIN number is different from the
Wireless Password/Network Security Key, usually you can only find it on the
label of your modem router.
2 ) If you cannot find the PIN or PIN failed, you may choose “Connecting using
a security key instead”, and then type in the Network Security Key/Wireless
Password;
3 ) If you continue to be told there is a network security key mismatch, it is
suggested to check the wireless password on your modem router.
Note: Wireless password/Network Security Key is case sensitive.
119
4 ) Connect to wireless network.
2. Windows was unable to connect to XXXX /Cannot join this network/Taking longer
than usual to connect to this network.
1 ) Check the wireless signal strength of your network, if it is weak (1~3 bars),
please move the router closer and try again;
2 ) Change the wireless Channel of the router to 1,6,or 11 to reduce interference
from other networks;
3 ) Re-install or update the driver for your wireless adapter of the computer;
4 ) Connect to wireless network.
120
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
OPERATING FREQUENCY(the maximum transmitted power)
2400 MHz -2483.5 MHz(20dBm)
5150 MHz -5250 MHz(23dBm)
5250 MHz -5350 MHz (23dBm)
5470 MHz -5725 MHz (30dBm)
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/53/EU, 2009/125/EC, 2011/65/EU and
(EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/
support/ce/
UK Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of the Radio Equipment Regulations 2017.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/
support/ukca/
RF Exposure Information
This device meets the EU requirements (2014/53/EU Article 3.1a) on the limitation of
exposure of the general public to electromagnetic fields by way of health protection.
The device complies with RF specifications when the device used at 20 cm from your
body.
National Restrictions
Attention: This device may only be used indoors in all EU member states, EFTA countries
and Northern Ireland.
Attention: This device may only be used indoors in Great Britain.
121
AT BE BG CH CY CZ DE DK
EE EL ES FI FR HR HU IE
IS IT LI LT LU LV MT NL
NO PL PT RO SE SI SK UK(IN)
UK
Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Caution:
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
DFS (Dynamic Frequency Selection) products that operate in the bands 5250- 5350
MHz, 5470-5600MHz, and 5650-5725MHz.
Avertissement:
1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement
pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable
aux systèmes de satellites mobiles utilisant les mêmes canaux;
Les produits utilisant la technique d’atténuation DFS (sélection dynamique des
fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.
122
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec
un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність
вимогам нормативних документів та вимогам, що передбачені чинними
законодавчими актами України.
Safety Information
• Keep the device away from water, fire, humidity or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
• Do not use damaged charger or USB cable to charge the device.
• Do not use any other chargers than those recommended
• Do not use the device where wireless devices are not allowed.
• Adapter shall be installed near the equipment and shall be easily accessible.
• Use only power supplies which are provided by manufacturer and in the original
packing of this product. If you have any questions, please don’t hesitate to contact us.
Operating Temperature: 0℃~40℃
Storage Temperature:-40℃~60℃
Please read and follow the above safety information when operating the device. We
cannot guarantee that no accidents or damage will occur due to improper use of the
device. Please use this product with care and operate at your own risk.
NCC Notice & BSMI Notice:
注意！
依據 低功率電波輻射性電機管理辦法
123
LP0002低功率射頻器材技術規範_章節3.8.2
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻
率、加大功率或變更原設計之特性及功能。
低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立
即停用，並改善至無干擾時方得繼續使用。
前述合法通信，指依電信管理法規定作業之無線電通信。
低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
應避免影響附近雷達系統之操作。
高增益指向性天線只得應用於固定式點對點系統。
安全諮詢及注意事項
• 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
• 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
• 注意防潮，請勿將水或其他液體潑灑到本產品上。
• 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋
開口。
• 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位
置中。
• 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項
工作。
限用物質含有情況標示聲明書
設備名稱：AC2100 Wireless MU-MIMO VDSL/ADSL
Modem Router
Equipment name
型號（型式）：Archer VR2100
Type designation (Type)
單元
Ｕnit
限用物質及其化學符號
Restricted substances and its chemical symbols
鉛
Lead
(Pb)
汞
Mercury
(Hg)
鎘
Cadmium
(Cd)
六價鉻
Hexavalent
chromium
(Cr+6)
多溴聯苯
Polybrominated
biphenyls
(PBB)
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
PCB ○ ○ ○ ○ ○ ○
外殼 ○ ○ ○ ○ ○ ○
電源供應器 −○ ○ ○ ○ ○
天線 ○ ○ ○ ○ ○ ○
124
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of
the restricted substance exceeds the reference percentage value of presence condition.
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the
percentage of reference value of presence.
備考3.〝−〞係指該項限用物質為排除項目。
Note 3：The “−” indicates that the restricted substance corresponds to the exemption.
Explanation of the symbols on the product label
Symbol Explanation
DC voltage
Class II equipment
AC voltage
Energy efficiency Marking
Polarity of output terminals
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization
or to the retailer when he buys a new electrical or electronic equipment.
Indoor use only