TP-Link EAP245(5-PACK) User Manual

Displayed below is the user manual for EAP245(5-PACK) by TP-Link which is a product in the Wireless Access Points category. This manual has pages.

Quick Installation Guide

Wireless Access Point

Setup with videos

Visit https://www.tp-link.com/support/setup-video/ or scan the QR code to search for

the setup video of your product model.

Note: The image may dier from the actual product.

Note: Make sure that the ceiling tile is bigger than the EAP.

The EAP can be ceiling-mounted or wall-mounted. Choose a mounting method according to your needs. Follow the

steps below for the appropriate installation.

Option1: Ceiling Mounting

Option2: Wall Mounting

Option 1: Ceiling Mounting Option 2: Wall Mounting

Wing Nuts (Qty.3)Washers (Qty.3) M3×30 Pan-head Screws (Qty.3)

Place the mounting bracket in the center of the ceiling tile.

Mark three positions for the screw holes and a position for

the Ethernet cable hole.

Drill three 4 mm diameter holes for the screws and a 25 mm

diameter hole for the Ethernet cable at the marked

positions.

Remove the ceiling tile.

Secure the mounting bracket to the ceiling tile using three

M3x30 pan-head screws, washers and wing nuts, as shown

on the left.

Feed the Ethernet cable through the hole and set the ceiling

tile back into place.

Connect the Ethernet cable to the ETHERNET port. Attach

the EAP to the mounting bracket by aligning the arrow mark

on the EAP with the arrow mark on the mounting bracket,

then rotate the EAP until it locks into place, as shown on the

left.

Drill Hole for Ethernet cable X3

Note: For security reasons, it is not recommended to install the EAP with the louver downward.

M3×20 Self-tapping Screws (Qty.3)

M3×28 Plastic Wall Anchors (Qty.3)

Insert the plastic wall anchors into the 6 mm diameter

holes.

Secure the mounting bracket to the wall by driving the

self-tapping screws into the anchors. Make sure that the

shoulders of the mounting bracket are on the outside.

Connect the Ethernet cable to the Ethernet port on the

E A P.

Attach the EAP to the mounting bracket by aligning the

arrow mark on the EAP with the arrow mark on the

mounting bracket, then rotate the EAP until it locks into

place, as shown on the left.

If your Ethernet cable feeds through the wall, you can

position the mounting bracket to make the cable

through the fixing hole. Mark three positions for the

screw holes and then drill three 6 mm diameter holes at

the marked positions.

To remove the EAP from the mounting bracket, insert a paper clip in the Security Slot to release the Locking Tab

and rotate the EAP until it is detached from the mounting bracket, as shown below.

Tip:

Security Slot

Locking Tab

Hardware Installation

Hardware Overview

Solid Green

: The device is initializing or working properly.

Flashing Green Slowly

: The device is in an isolated state.

Flashing Yellow

: The device is working abnormally.

Flashing Yellow, Green

: The device is updating. Do not disconnect or power o the device.

Quickly Flashing Yellow, Green: The device is being reset to its factory default settings.

LED Indicator

Front Panel

Rear Panel

The port is used to connect to the PoE port of the PoE adapter (not provided) or a PSE (Power Sourcing

Equipment), such as a PoE switch, for both data transmission and Power over Ethernet (PoE) through Ethernet

cable. The PSE should complies with LPS or PS2 standard.

ETH1 (PoE)

The port is a Gigabit Ethernet port used for bridging.

ETH2

With the device powered on, press and hold the button for about 5 seconds until the LED is quickly flashing

yellow then green, then release the button. The device will restore to factory default settings.

RESET

The EAP can be powered via a power adapter or a PSE (such as a PoE switch) which complies with LPS or PS2

standard.

Option1: Via PoE Switch

Option2: Via PoE Adapter (Not Included*)

PoE Switch

Connect an Ethernet cable from the PoE switch to the Ethernet port (ETH1).

1. Connect the Ethernet cable from the Ethernet port (ETH1) of the EAP device to the provided PoE adapter’s PoE

port.

2. Connect an Ethernet cable from your LAN to the PoE adapter’s LAN port.

3. Connect the power cord to the adapter’s power socket. Connect the other end of the power cord to a standard

electrical wall outlet.

Internet

Clients

Router

EAP

The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU

General Public License (“GPL”). As applicable, the terms of the GPL and any information on obtaining access to the respective

GPL Code used in TP-Link products are available to you in GPL-Code-Centre under (https://www.tp-link.com/en/support/gpl/).

The respective programs are distributed WITHOUT ANY WARRANTY and are subject to the copyrights of one or more

authors. For details, see the GPL Code and other terms of the GPL.

For technical support, the user guide and other information,

please visit https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides,

welcome to email techwriter@tp-link.com.cn.

To ask questions, find answers, and communicate with TP-Link users or engineers,

please visit https://community.tp-link.com to join TP-Link Community.

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you

need service, please contact us.

Do not use the device where wireless devices are not allowed.

Do not use damaged charger or USB cable to charge the device.

Do not use any other chargers than those recommended.

Adapter shall be installed near the equipment and shall be easily accessible.

Power Supply

Software Conguration

PoE Adapter

PoE LAN

(Up to 100m)

1 2

Choose from the following methods to set up your EAPs:

Method 1: Standalone Mode

Note:

Via Omada App

1. Connect wirelessly by using the default SSID (format: TP-Link_2.4GHz/5GHz_XXXXXX) printed on the label

at the bottom of the product.

2. Launch a web browser and enter http://tplinkeap.net in the address bar. Use admin for both Username and

Password to log in.

3. Set up a new Username and Password for secure management purpose. Modify the wireless parameters

and reconnect your wireless devices to the new wireless network.

To configure other EAPs, connect your device to the EAP by the coresponding default SSID and repeat the

steps listed above. You can configure some basic functions in Standalone Mode. If you want to configure

advanced functions, use Controller Mode.

1. Download the TP-Link Omada App on your mobile device. It can be downloaded from App Store or Google Play:

2. Connect your mobile device to the EAP by using the default SSID (format: TP-Link_2.4GHz/5GHz_XXXXXX)

printed on the label at the bottom of the product.

3. Open the Omada App, and wait for the EAP to appear on the Standalone APs page. Tap on the EAP you want to

congure.

The Omada App is designed to help you quickly configure the common settings. If you want to configure

advanced settings, use the web page of your EAP or use Controller Mode.

Via Web Browser

Scan for Omada App Download Omada App

To configure and manage EAPs separately (Convenient for a small network with only a few devices)

Method 1: Standalone Mode

Before you start, be sure to power up and connect your devices according to the topology figure.

A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses to the EAPs

and clients in your local network.

To configure and manage EAPs in batches on a central platform, namely Omada Controller.

Method 2: Controller Mode

Via Omada App

Method 2: Controller Mode

1. Download the TP-Link Omada App on your mobile device. It can be downloaded from App Store or Google Play:

Scan for Omada App Download Omada App

Local Management

2. Launch your Omada App and configure the controller at a local site or remote site.

a. Connect your mobile device to the EAP by using the default SSID (format:

TP-Link_2.4GHz/5GHz_XXXXXX) printed on the label at the bottom of the product.

b. Launch Omada App and go to Local Access, tap the + button on the upper-right corner to add the

controller. Then you can further congure the controller.

Switch

Router

Clients

Omada Hardware Controller EAP EAP EAP

(OC200/OC300)

Switch

Router

Clients

EAP EAP

EAP

Controller

Omada Software Controller

running on the Host PC

Note:

Before you start, be sure to power up and connect your devices according to the topology figure.

A DHCP server (typically a router with DHCP function enabled) is required to assign IP addresses to the EAPs

and clients in your local network.

Omada Controller must have network access to your Omada devices (the router, switch, and EAPs) in order to

find, adopt, and manage them.

Choose from the following two types of Omada Controller:

On a PC with Windows OS or Linux OS, download the Omada Software Controller from

https://www.tp-link.com/support/download/omada-software-controller/. Then run the file and follow the wizard

to install and launch the Omada Software Controller.

To manage your devices, Omada Software Controller needs to keep running on your computer.

Type 1: Omada Software Controller

Omada Hardware Controller (OC200/OC300) is a good alternative if you have no spare PC to keep running

Omada Software Controller in the network. It needs to be purchased additionally.

For more details, refer to the Installation Guide of OC200/OC300.

Type 2: Omada Hardware Controller (OC200/OC300)

1. Open the Omada Controller’s web page.

3. After the quick setup, the login page appears. Enter the username and password you have created and click

4. (For Remote Management) You can remotely access and manage your controller via Omada Cloud

Service.

2. On the Omada Controller’s web page, follow the wizard to complete the quick setup.

b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Enter your TP-Link ID

and password to log in. A list of controllers that have been bound with your TP-Link ID will appear. Then

you can click Launch to further configure the controller.

a. You need rst nd the IP address of the router. Open the command line on your PC and enter ipconfig. In

the result list, find the Default Gateway, which is also the IP address of the router.

c. Enter the IP address of the your controller in the address bar to open its web page.

b. Launch a web browser and enter the IP address of the router. Log into the router’s web page, and both the

username and password are admin by default. Then go to Network > LAN > DHCP Client List to find the

IP address of your controller according to its MAC address.

Via Web Browser

Launch the Omada Software Controller on your PC. After the initiation process, the controller automatically

opens its web page. If not, click Launch a Browser to Manage the Network.

As Omada Hardware Controller gets its IP address from the DHCP server of the router, we don’t know its IP

address explicitly. However, we can nd it out on the router’s DHCP client list.

For Omada Hardware Controller

Note: Before you start, make sure that both your controller and your PC can access the internet.

For Omada Software Controller

a. Make sure that Cloud Access is enabled on your controller and your controller has been bound with your

TP-Link ID. On the Omada Controller’s web page, go to Settings > Cloud Access to enable Cloud Access

and bind your TP-Link ID. If you have set it up in the quick setup, skip this step.

For Omada Software Controller

b. Launch a web browser and enter https://omada.tplinkcloud.com in the address bar. Enter your TP-Link ID

and password to log in. Click + Add Controller and choose Hardware Controller to add your controller.

Then you can further configure the controller.

a. Make sure that Cloud Access is enabled on your controller. By default, Cloud Access is enabled. Make

sure that the Cloud LED is flashing slowly.

For Omada Hardware Controller

a. Make sure that Cloud Access is enabled on your controller and your controller has been bound with

your TP-Link ID.

b. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. A list of controllers that

have been bound with your TP-Link ID will appear. Then you can further configure the controller.

Remote Management

Note: Before you start, make sure that both your controller and mobile device can access the internet.

For Omada Software Controller

a. Make sure that Cloud Access is enabled on your controller. By default, Cloud Access is enabled. Make

sure that the Cloud LED is flashing slowly.

b. Launch Omada App and log in with your TP-Link ID. Then go to Cloud Access. Tap the + button on the

upper-right to add your controller. Then you can further configure the controller.

For Omada Hardware Controller

Operating Temperature: 0°C-50°C (32°F-122°F). Operating Humidity: 10%-90%RH, Non-condensing.

Storage Temperature: -40°C-70°C (-40°F-158°F). Storage Humidity: 5%-90%RH, Non-condensing.

*For EAP245 (5-packs), POE adapters are sold separately.