Table of Contents
- Package Contents
- Chapter 1 About this Guide
- Chapter 2 Introduction
- Chapter 3 Login to the Switch
- Chapter 4 System
- Chapter 5 Switching
- Chapter 6 VLAN
- Chapter 7 Spanning Tree
- Chapter 8 Multicast
- Chapter 9 QoS
- Chapter 10 PoE
- Chapter 11 ACL
- Chapter 12 SNMP
- Chapter 13 LLDP
- Chapter 14 Maintenance
- Appendix A: Specifications
- Appendix B: Configuring the PCs
- Appendix C: Glossary
TP-Link T1500-28PCT(TL-SL2428P) User Manual
Displayed below is the user manual for T1500-28PCT(TL-SL2428P) by TP-Link which is a product in the Network Switches category. This manual has pages.
T1500-28PCT
Smart PoE Switch
REV1.0.0
1910
011254
III
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
IV
Safety Information
When product has power button, the power button is one of the way to shut off the product;
When there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被
要求採取某些適當的對策。
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US
III
CONT ENTS
Package Contents ....................................................................................................................... 1
Chapter 1 About this Guide ........................................................................................................ 2
1.1 Intended Readers....................................................................................................... 2
1.2 Conventions ............................................................................................................... 2
1.3 Overview of This Guide .............................................................................................. 2
Chapter 2 Introduction................................................................................................................ 6
2.1 Overview of the Switch ............................................................................................... 6
2.2 Main Features ............................................................................................................ 6
2.3 Appearance Description ............................................................................................. 7
2.3.1 Front Panel ...................................................................................................... 7
2.3.2 Rear Panel ...................................................................................................... 9
Chapter 3 Login to the Switch .................................................................................................. 10
3.1 Login ........................................................................................................................ 10
3.2 Configuration.............................................................................................................11
Chapter 4 System .................................................................................................................... 12
4.1 System Info .............................................................................................................. 12
4.1.1 System Summary .......................................................................................... 12
4.1.2 Device Description......................................................................................... 14
4.1.3 System Time .................................................................................................. 14
4.1.4 Daylight Saving Time ..................................................................................... 15
4.1.5 System IP ...................................................................................................... 16
4.2 User Management.................................................................................................... 18
4.2.1 User Table ..................................................................................................... 18
4.2.2 User Config ................................................................................................... 18
4.3 System Tools............................................................................................................ 19
4.3.1 Config Restore............................................................................................... 19
4.3.2 Config Backup ............................................................................................... 20
4.3.3 Firmware Upgrade ......................................................................................... 20
4.3.4 System Reboot .............................................................................................. 21
4.3.5 System Reset ................................................................................................ 21
4.4 Access Security ....................................................................................................... 22
4.4.1 Access Control .............................................................................................. 22
4.4.2 SSL Config .................................................................................................... 23
4.4.3 SSH Config.................................................................................................... 25
Chapter 5 Switching ................................................................................................................. 32
5.1 Port .......................................................................................................................... 32
IV
5.1.1 Port Config .................................................................................................... 32
5.1.2 Port Mirror ..................................................................................................... 33
5.1.3 Port Security .................................................................................................. 35
5.1.4 Port Isolation ................................................................................................. 37
5.1.5 Loopback Detection ....................................................................................... 38
5.2 LAG ......................................................................................................................... 39
5.2.1 LAG Table...................................................................................................... 40
5.2.2 Static LAG ..................................................................................................... 41
5.2.3 LACP Config.................................................................................................. 42
5.3 Traffic Monitor .......................................................................................................... 44
5.3.1 Traffic Summary ............................................................................................ 44
5.3.2 Traffic Statistics.............................................................................................. 45
5.4 MAC Address ........................................................................................................... 46
5.4.1 Address Table................................................................................................ 47
5.4.2 Static Address................................................................................................ 48
5.4.3 Dynamic Address........................................................................................... 49
5.4.4 Filtering Address ............................................................................................ 51
5.5 DHCP Filtering ......................................................................................................... 52
Chapter 6 VLAN....................................................................................................................... 56
6.1 802.1Q VLAN ........................................................................................................... 57
6.1.1 VLAN Config.................................................................................................. 58
6.2 Application Example for 802.1Q VLAN ..................................................................... 60
Chapter 7 Spanning Tree ......................................................................................................... 62
7.1 STP Config............................................................................................................... 67
7.1.1 STP Config .................................................................................................... 67
7.1.2 STP Summary ............................................................................................... 69
7.2 Port Config ............................................................................................................... 69
7.3 MSTP Instance......................................................................................................... 71
7.3.1 Region Config................................................................................................ 71
7.3.2 Instance Config.............................................................................................. 72
7.3.3 Instance Port Config ...................................................................................... 73
7.4 STP Security ............................................................................................................ 75
7.4.1 Port Protect ................................................................................................... 75
7.4.2 TC Protect ..................................................................................................... 78
7.5 Application Example for STP Function ..................................................................... 78
Chapter 8 Multicast .................................................................................................................. 82
8.1 IGMP Snooping........................................................................................................ 84
V
8.1.1 Snooping Config ............................................................................................ 85
8.1.2 Port Config .................................................................................................... 86
8.1.3 VLAN Config.................................................................................................. 87
8.1.4 Multicast VLAN .............................................................................................. 89
8.2 Multicast IP .............................................................................................................. 92
8.2.1 Multicast IP Table........................................................................................... 92
8.2.2 Static Multicast IP .......................................................................................... 93
8.3 Multicast Filter .......................................................................................................... 94
8.3.1 IP-Range ....................................................................................................... 94
8.3.2 Port Filter....................................................................................................... 95
8.4 Packet Statistics ....................................................................................................... 96
Chapter 9 QoS ......................................................................................................................... 98
9.1 DiffServ .................................................................................................................. 101
9.1.1 Port Priority.................................................................................................. 101
9.1.2 802.1P/CoS Mapping................................................................................... 102
9.1.3 DSCP Priority .............................................................................................. 103
9.1.4 Schedule Mode............................................................................................ 104
9.2 Bandwidth Control .................................................................................................. 105
9.2.1 Rate Limit .................................................................................................... 105
9.2.2 Storm Control .............................................................................................. 106
9.3 Voice VLAN............................................................................................................ 108
9.3.1 Global Config................................................................................................110
9.3.2 Port Config ...................................................................................................110
9.3.3 OUI Config.................................................................................................... 111
Chapter 10 PoE ........................................................................................................................114
10.1 PoE Config..............................................................................................................114
10.1.1 PoE Config ...................................................................................................115
10.1.2 PoE Profile ...................................................................................................116
10.2 PoE Time-Range.....................................................................................................117
10.2.1 Time-Range Summary ..................................................................................117
10.2.2 PoE Time-Range Create...............................................................................118
10.2.3 PoE Holiday Config.......................................................................................119
Chapter 11 ACL ....................................................................................................................... 120
11.1 ACL Config............................................................................................................. 120
11.1.1 ACL Summary ............................................................................................. 120
11.1.2 ACL Create.................................................................................................. 120
11.1.3 MAC ACL..................................................................................................... 121
VI
11.1.4 Standard-IP ACL .......................................................................................... 122
11.1.5 Extend-IP ACL ............................................................................................. 122
11.1.6 Combined ACL ............................................................................................ 123
11.2 Policy Config .......................................................................................................... 124
11.2.1 Policy Summary........................................................................................... 124
11.2.2 Policy Create ............................................................................................... 125
11.2.3 Action Create............................................................................................... 125
11.3 Policy Binding ........................................................................................................ 126
11.3.1 Binding Table ............................................................................................... 126
11.3.2 Port Binding ................................................................................................. 127
11.3.3 VLAN Binding .............................................................................................. 127
11.4 Application Example for ACL .................................................................................. 128
Chapter 12 SNMP .................................................................................................................... 131
12.1 SNMP Config ......................................................................................................... 133
12.1.1 Global Config............................................................................................... 133
12.1.2 SNMP View ................................................................................................. 134
12.1.3 SNMP Group ............................................................................................... 135
12.1.4 SNMP User ................................................................................................. 136
12.1.5 SNMP Co mmunity ....................................................................................... 138
12.2 Notification ............................................................................................................. 140
12.3 RMO N.................................................................................................................... 141
12.3.1 History Control............................................................................................. 142
12.3.2 Event Config ................................................................................................ 143
12.3.3 Alarm Config................................................................................................ 143
Chapter 13 LLDP ..................................................................................................................... 146
13.1 Basic Config........................................................................................................... 150
13.1.1 Global Config............................................................................................... 150
13.1.2 Port Config .................................................................................................. 151
13.2 Device Info ............................................................................................................. 152
13.2.1 Local Info..................................................................................................... 152
13.2.2 Neighbor Info ............................................................................................... 153
13.3 Device Statistics ..................................................................................................... 153
13.4 LLDP-MED............................................................................................................. 155
13.4.1 Global Config............................................................................................... 156
13.4.2 Port Config .................................................................................................. 157
13.4.3 Local Info..................................................................................................... 158
13.4.4 Neighbor Info ............................................................................................... 159
VII
Chapter 14 Maintenance .......................................................................................................... 161
14.1 System Monitor ...................................................................................................... 161
14.1.1 CPU Monitor ................................................................................................ 161
14.1.2 Memory Monitor........................................................................................... 162
14.2 Log......................................................................................................................... 162
14.2.1 Log Table ..................................................................................................... 163
14.2.2 Local Log..................................................................................................... 163
14.2.3 Remote Log ................................................................................................. 164
14.2.4 Backup Log ................................................................................................. 165
14.3 Device Diagnostics................................................................................................. 166
14.3.1 Cable Test ................................................................................................... 166
14.4 Network Diagnostics .............................................................................................. 167
14.4.1 Ping ............................................................................................................. 167
14.4.2 Tracert ......................................................................................................... 168
Appendix A: Specifications ....................................................................................................... 169
Appendix B: Configuring the PCs............................................................................................. 170
Appendix C: Glossary .............................................................................................................. 173
1
Package Contents
The following items should be found in your box:
One T1500-28PCT Smart PoE Switch
One power cord
Two mounting brackets and other fittings
Installation Guide
Resource CD for T1500-28PCT switch, including:
• This User Guide
• CLI Reference Guide
• SNMP Mibs
• Other Helpful Information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
2
Chapter 1 About this Guide
This User Guide contains information for setup and management of T1500-28PCT Smart PoE
Switch. Please read this guide carefully before operation.
1.1 Intended Readers
This Guide is intended for network managers familiar with IT concepts and network terminologies.
1.2 Conventions
In this Guide the following conventions are used:
The switch or T1500-28PCT mentioned in this Guide stands for T1500-28PCT Smart PoE
Switch without any explanation.
Menu Name→Submenu Name→Tab page indicates the menu structure. Syste m→Sys t e m
Info→Syste m Summary means the System Summary page under the System Info menu
option that is located under the System menu.
Bold font indicates a button, a toolbar icon, menu or menu item.
Symbols in this Guide：
Symbol Description
Note: Ignoring this type of note might result in a malfunction or damage to the device.
Tips:
This format indicates important information that helps you make better us
e of
your device.
1.3 Overview of This Guide
Chapter Introduction
Chapter 1 About This Guide Introduces the guide structure and conventions.
Chapter 2 Introduction Introduces the fea
tures, application and appearance of
T1500-28PCT switch.
Chapter 3 Login to the Switch Introduces how to log on to the Web management page.
3
Chapter Introduction
Chapter 4 System This module is used to configure syst
em properties of the
switch. Here mainly introduces:
System Info: Configure the description, system time and
network parameters of the switch.
User Management
: Configure the user name and password
for users to log on to the Web management page with a
certain access level.
System Tools: Manage the configuration file of the switch.
Access Security:
Provide different security measures for the
login to enhance the configuration management security.
Chapter 5 Switching This modu
le is used to configure basic functions of the switch.
Here mainly introduces:
Port: Configure the basic features for the port.
LAG: Configure Link Aggregation Group. LAG is to combine a
number of ports together to make a single high-bandwidth
data path.
Traffic Monitor: Monitor the traffic of each port.
MAC Address: Configure the address table of the switch.
DHCP Filtering: Monitor the process of the h
ost obtaining the
IP address from DHCP server.
Chapter 6 VLAN This module is u
sed to configure VLANs to control broadcast in
LANs. Here mainly introduces:
802.1Q VLAN: Configure port-based VLAN.
Chapter 7 Spanning Tree
This module is used to configure spanning tree function of the
switch. Here mainly introduces:
STP Config: Configure and view the global settings of
spanning tree function.
Port Config: Configure CIST parameters of ports.
MSTP Instance: Configure MSTP instances.
STP Security: Configure protection function to prevent
devices from any malicious attack against STP features.
Chapter 8 Multicast
This module is used to configure multicast function of the switch.
Here mainly introduces:
IGMP Snooping: Configure global parameters of IGMP
Snooping function
, port properties, VLAN and multicast
VLAN.
Multicast IP: Configure multicast IP table.
Multicast Filter: Configure multicast filter feature to restrict
users ordering multicast programs.
Packet Statistics:
View the multicast data traffic on each port
of
the switch, which facilitates you to monitor the IGMP
messages in the network.
4
Chapter Introduction
Chapter 9 QoS
This module is used to configure QoS function to provide
different quality of service for various network applications and
requirements. Here mainly introduces:
DiffServ: Configure
priorities, port priority, 802.1P priority and
DSCP priority.
Bandwidth Control: Configure rate limit feature to control the
traffic rate on each port; configure storm control feature to
filter broadcast, multicast and UL frame in the network.
Voice VLAN: Configure voice VLAN to transmit voice data
stream within the specified VLAN so as to ensure the
transmission priority of voice data stream and voice quality.
Chapter 10 ACL This modul
e is used to configure match rules and process
policies of packets to filter packets in order to control the access
of the illegal users to the network. Here mainly introduces:
ACL Config: ACL rules.
Policy Config: Configure operation policies.
Policy Bind
ing: Bind the policy to a port/VLAN to take its
effect on a specific port/VLAN.
Chapter 11 PoE This
module is used to configure the PoE function for the switch
to supply power for PD devices. Here mainly introduces:
PoE Config: Configure PoE function globally.
PoE Time-Range: Configure the effective time for
PoE port to
supply power.
Chapter 12 SNMP
This module is used to configure SNMP function to provide a
management frame to monitor and maintain the network
devices. Here mainly introduces:
SNMP Config: Configure global settings of SNMP function.
Notification: Configure notification function for the
management station to monitor and process the events.
RMON: Configure RMON function to monitor network more
efficiently.
Chapter 13 LLDP
This module is used to configure LLDP function to provide
information for SNMP applications to simplify troubleshooting.
Here mainly introduces:
Basic Config: Configure the LLDP parameters of the device.
Device Info: V
iew the LLDP information of the local device
and its neighbors
Device Statistics: View the LLDP statistics of the local device
LLDP-MED: Configure LLDP-MED parameters of the device.
Chapter 15 Maintenance
This module is used to assemble the commonly used system
tools to manage the switch. Here mainly introduces:
System Monitor: Monitor the memory and CPU of the switch.
Log: View configuration parameters on the switch.
Device Diagnostics: Test the con
nection status of the cable
connected to the switch.
Net work Diagnostics
: Test if the destination is reachable and
the account of router hops from the switch to the destination.
6
Chapter 2 Introduction
Thanks for choosing the T1500-28PCT Smart PoE Switch!
2.1 Overview of the Switch
Designed for workgroups and departments, T1500-28PCT from TP-LINK provides wire-speed
performance and full set of layer 2 management features. It provides a variety of service features
and multiple powerful functions with high security.
The EIA-standardized framework and smart configuration capacity can provide flexible solutions
for a variable scale of networks. QoS and IGMP snooping/filtering optimize voice and video
application. Link aggregation (LACP) increase aggregated bandwidth, optimizing the transport of
business critical data. SNMP, RMON, WEB/Telnet/SSH Log-in bring abundant management
policies. T1500-28PCT switch integrates multiple functions with excellent performance, and is
friendly to manage, which can fully meet the need of the users demanding higher networking
performance.
2.2 Main Features
• Resiliency and Availability
+ IEEE 802.1s Multiple Spanning Tree provides high link availability in multiple VLAN
environments.
+ Multicast snooping automatically prevents flooding of IP multicast traffic.
+ Root Guard protects root bridge from malicious attack or configuration mistakes
• Layer 2 Switching
+ Supports up to 512 VLANs simultaneously (out of 4K VLAN IDs).
• Quality of Service
+ Supports L2/L3 granular CoS with 4 priority queues per port.
+ Rate limiting confines the traffic flow accurately according to the preset value.
• Manageability
+ Supports Telnet, SNMP v1/v2c/v3, RMON and web access.
+ Port Mirroring enables monitoring selected ingress/egress traffic.
7
2.3 Appearance Description
2.3.1 Front Panel
The front panel of T1500-28PCT is shown as Figure 2-1.
Figure 2-1 Front Panel of T1500-28PCT
The following parts are located on the front panel of the switch:
LEDs
T1500-28PCT has an LED mode switch button which is for switching the LED status indication.
When the Speed LED is on, the port LED is indicating the data transmission rate. When the PoE
LED is on, the port LED is indicating the power supply status. By default the Speed LED is on.
Pressing the mode switch button, the Speed LED will turn off and the PoE LED will light up. Then
the PoE LED will turn off after being on for 60 seconds and the Speed LED will light up again.
When the 10/100M is on, the port LED is indicating the data transmission rate.
Name Status Indication
PWR
On The switch is powered on.
Off
The switch is powered off or power supply is abnormal.
Flashing Power supply is abnormal.
SYS Flashing The switch works properly.
On/Off The switch works improperly.
10/100M or PoE
Green On A 100
Mbps device is connected to the corresponding
port, but no activity.
Flashing Data is being transmitted or received.
Yellow On
A 10Mbps device is connected to the corresponding
port, but no activity.
Flashing Data is being transmitted or received.
Off No device is connected to the corresponding port.
8
Name Status Indication
10/100/1000M
Green On
A 1000Mbps device is connected to the corresponding
port, but no activity.
Flashing Data is being transmitted or received.
Yellow On A 10/100Mbps d
evice is connected to the
corresponding port, but no activity.
Flashing Data is being transmitted or received.
Off No device is connected to the corresponding port.
When the PoE LED is on, the port LED is indicating the power supply status.
Name Status Indication
PWR
On The switch is powered on.
Off The switch is powered off or power supply is abnormal.
Flashing Power supply is abnormal.
SYS Flashing The switch works properly.
On/Off The switch works improperly.
PoE MAX
On The remaining PoE power≤7W.
Flashing The remaining PoE power keeps ≤
7W after this LED is
on for 2 minutes.
Off The remaining PoE power>7W.
10/100M or PoE
Green
On The port is supplying power normally.
Flashing The supply power exceeds the corresponding port’s
maximum power.
Yellow On Overload or short circuit is detected.
Flashing Power-on self-test has failed.
Off No PoE power supply is provided on the port.
1000M
Green On
A 1000Mbps device is connected to the corresponding
port, but no activity.
Flashing Data is being transmitted or received.
Yellow On
A 10/100Mbps device is connected to the corresponding
port, but no activity.
Flashing Data is being transmitted or received.
Off No device is connected to the corresponding port.
Re set: Press this button for five seconds or above to reset the software setting back to factory
default setting.
10/100Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps or
100Mbps. Each has a corresponding 10/100M or PoE LED.
10/100/1000Mbps Ports: Designed to connect to the device with a bandwidth of 10Mbps,
100Mbps or 1000Mbps. Each has a corresponding 1000M LED.
9
SFP Ports: Designed to install the SFP module. T1500-28PCT features some SFP transceiver
slots that are shared with the associated RJ45 ports. The associated two ports are referred as a
"Combo" port, which means they cannot be used simultaneously, otherwise only SFP port
works. Meanwhile, the associated two ports share the same LED. For T1500-28PCT, Port 27
shares the same LED with Port 27F and Port 28 shares the same LED with Port 28F.
Note:
When using the SFP port with a 100Mbps module or a gigabit module, you need to configure its
corresponding Speed and Duplex mode on Switching→Port→Port Config page or through
Telnet. For 100M module, please select 100MFD while select 1000MFD for gigabit module. By
default, the Speed and Duplex mode of SFP port is 1000MFD.
2.3.2 Rear Panel
The rear panel of T1500-28PCT features a Kensington security socket, a power socket and a
Grounding Terminal (marked with ).
The rear panel of T1500-28PCT is shown as the following figure.
Figure 2-2 Rear Panel of T1500-28PCT
Kensington Security Socket: Secure the lock (not provided) into the security slot to prevent
the device from being stolen.
Grounding Terminal: T1500-28PCT already comes with Lightning Protection Mechanism. You
can also ground the switch through the PE (Protecting Earth) cable of AC cord or with the
ground cable.
AC Po wer Socket: Connect the female connector of the power cord here, and the male
connector to the AC power outlet. Please make sure the voltage of the power supply meets the
requirement of the input voltage (100-240V~ 50/60Hz 3.5A).
Return to CONTENTS
10
Chapter 3 Login to the Switch
3.1 Login
1) To access the configuration utility, open a web-browser and type in the default address
http://192.168.0.1 in the address field of the browser, then press the Ente r key.
Figure 3-1 Web-browser
Tips:
To log in to the s witch, the IP address of your PC should be set in the same subnet addresses of
the switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is
255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B.
2) After a moment, a login window will appear, as shown in Figure 3-2. Enter admin for the User
Name and Password, both in lower case letters. Then click the Login button or press the Enter
key.
Figure 3-2 Login
11
3.2 Configuration
After a successful login, the main page will appear as Figure 3-3, and you can configure the
function by clicking the setup menu on the left side of the screen.
Figure 3-3 Main Setup-Menu
Note:
Clicking Apply can only make the new configurations effective before the switch is rebooted. If
you want to keep the configurations effective even the switch is rebooted, please click Save
Config. You are suggested to click Save Config before cutting off the power or rebooting the
switch to avoid losing the new configurations.
Return to CONTENTS
12
Chapter 4 System
The System module is mainly for system configuration of the switch, including four submenus:
System Info, User Manage, System Tools and Access Security.
4.1 System Info
The System Info, mainly for basic properties configuration, can be implemented on Sys t e m
Summary, Device Description, Syste m Time , Daylight Saving Time and Syste m IP pages.
4.1.1 System Summary
On this page you can view the port connection status and the system information.
The port status diagram shows the working status of 24 10/100Mbps RJ45 ports, 4
10/100/1000Mbps RJ45 ports and 2 SFP ports of the switch. Ports 1 to 24 are 10/100Mbps ports.
Ports 25-28 are 10/100/1000Mbps ports, among which ports 27 and 28 are Combo ports with SFP
ports labeled 27F and 28F.
Choose the menu Syste m→System Info→Syste m Summary to load the following page.
Figure 4-1 System Summary
Port Status
Indicates the 100Mbps port is not connected to a device.
Indicates the 100Mbps port is at the speed of 100Mbps.
Indicates the 100Mbps port is at the speed of 10Mbps.
Indicates the 1000Mbps port is not connected to a device.
Indicates the 1000Mbps port is at the speed of 1000Mbps.
13
Indicates the 1000Mbps port is at the speed of 10Mbps or 100Mbps.
Indicates the SFP port is not connected to a device.
Indicates the SFP port is at the speed of 1000Mbps.
Indicates the SFP port is at the speed of 100Mbps.
When the cursor moves on the port, the detailed information of the port will be displayed.
Figure 4-2 Port Information
Port Info
Port: Displays the port number of the switch.
Typ e :
Displays the type of the port.
Rate:
Displays the maximum transmission rate of the port.
Status:
Displays the connection status of the port.
Click a port to display the bandwidth utilization on this port. The actual rate divided by theoretical
maximum rate is the bandwidth utilization. The following figure displays the bandwidth utilization
monitored every four seconds. Monitoring the bandwidth utilization on each port facilitates you to
monitor the network traffic and analyze the network abnormities.
Figure 4-3 Bandwidth Utilization
Bandwidth Utilization
Rx:
Select Rx to display the bandwidth utilization of receiving packets
on this port.
14
Tx: Select Tx to display the bandwidt
h utilization of sending packets
on this port.
4.1.2 Device Description
On this page you can configure the description of the switch, including device name, device location
and system contact.
Choose the menu Syste m→System Info→Device Description to load the following page.
Figure 4-4 Device Description
The following entries are displayed on this screen:
Device Description
Device Name: Enter the name of the switch.
Device Location: Enter the location of the switch.
System Contact: Enter your contact information.
4.1.3 System Time
System Time is the time displayed while the switch is running. On this page you can configure the
system time and the settings here will be used for other time-based functions.
You can manually set the system time or synchronize with PC’s clock as the system time.
Choose the menu Syste m→System Info→Syste m Time to load the following page.
Figure 4-5 System Time
15
The following entries are displayed on this screen:
Time Info
Current System Date:
Displays the current date and time of the switch.
Current Time Source:
Displays the current time source of the switch.
Time Config
Manual:
When this option is selected, you can set the date and time
manually.
Get Time from NTP
Server:
When this option is selected, you can configure the time zone
and the IP address for the NTP Server. The switch will get UTC
automatically if it has connected to an NTP Server.
Time Zone: Select your local time.
Primary/Secondary NTP Server: Enter the IP address
for the
NTP Server.
Update Rate: Specify the rate fetching time from NTP server.
Synchronize with
PC’S Clock:
When this option is selected, the administrator PC’s
clock is
utilized.
Note:
1. The system time will be restored to the default when the switch is restarted and you need to
reconfigure the system time of the switch.
2. When Get Time from NTP Server is selected and no time server is configured, the switch will
get time from the time server of the Internet if it has connected to the Internet.
4.1.4 Daylight Saving Time
Here you can configure the Daylight Saving Time of the switch.
Choose the menu Syste m→System Info→Daylight Saving Time to load the following page.
Figure 4-6 Daylight Saving Time
16
The following entries are displayed on this screen:
DST Config
DST Status: Enable or disable the DST.
Predefined Mode: Select a predefined DST configuration.
USA: Second Sunday in March, 02:00 ~ First
Sunday in
November, 02:00.
Australia: First Sunday in October, 02:00 ~ First Sunday in
April, 03:00.
Europe: Last Sunday in March, 01:00 ~
Last Sunday in
October, 01:00.
New Zealand: Last Sunday in September, 02:00 ~ Fir
st
Sunday in April, 03:00.
Recurring Mode:
Specify the DST configuration in recurring mode. This
configuration is recurring in use.
Offset: Specify the time adding in minute
s when Daylight
Saving Time comes.
Start/End Time: Select starting time and ending time of
Daylight Saving Time.
Date Mode: Specify the DST configuration in Da
te mode. This configuration is
recurring in use.
Offset: Specify the time adding in minutes when
Daylight
Saving Time comes.
Start/End Time: Select starting time and ending time of
Daylight Saving Time.
Note:
1. When the DST is disabled, the predefined mode, recurring mode and date mode cannot be
configured.
2. When the DST is enabled, the default daylight saving time is of Europe in predefined mode.
4.1.5 System IP
Each device in the network possesses a unique IP address. You can log on to the Web
management page to operate the switch using this IP address. The switch supports three modes
to obtain an IP address: Static IP, DHCP and BOOTP. The IP address obtained using a new mode
will replace the original IP address. On this page you can configure the system IP of the switch.
17
Choose the menu Syste m→System Info→Syste m IP to load the following page.
Figure 4-7 System IP
The following entries are displayed on this screen:
IP Config
M AC Ad d r e ss: Displays MAC address of the switch.
IP Address Mode: Select the mode to obtain IP address for the switch.
Static IP: When this option is selected, you should enter IP
address, Subnet Mask and Default Gateway manually.
DHCP: When this option is selected, the switch will obtain
network parameters from the DHCP Server.
B
OOTP: When this option is selected, the switch will obtain
network parameters from the BOOTP Server.
Management VLAN:
Enter the ID of management VLAN, the only VLAN through which
you can get access to the switch. By default VLAN1 owning all the
ports is t
he Management VLAN and you can access the switch via
any port on the switch. However, if another VLAN is created and
set to be the Management VLAN, you may have to reconnect the
management station to a port that is a member of the
Management VLAN.
IP Ad d ress:
Enter the system IP of the switch. The default system IP is
192.168.0.1 and you can change it appropriate to your needs.
Subnet Mask: Enter the subnet mask of the switch.
Default Gateway: Enter the default gateway of the switch.
Note:
1. Changing the IP address to a different IP segment will interrupt the network communication, so
please keep the new IP address in the same IP segment with the local network.
2. The switch only possesses an IP address. The IP address configured will replace the original
IP address.
3. If the switch gets the IP address from DHCP server, you can see the configuration of the
switch in the DHCP server; if DHCP option is selected but no DHCP server exists in the
network, the switch will keep obtaining IP address from DHCP server until success.
18
4. If DHCP or BOOTP option is selected, the switch will get network parameters dynamically
from the Internet, which means that IP address, subnet mask and default gateway cannot be
configured.
5. By default, the IP address is 192.168.0.1.
4.2 User Management
User Management functions to configure the user name and password for users to log on to the
Web management page with a certain access level so as to protect the settings of the switch from
being randomly changed.
The User Management function can be implemented on User Table and Use r Config pages.
4.2.1 User Table
On this page you can view the information about the current users of the switch.
Choose the menu Syste m→User Manageme nt→User Table to load the following page.
Figure 4-8 User Table
4.2.2 User Config
On this page you can configure the access level of the user to log on to the Web management
page. The switch provides two access levels: Guest and Admin. The guest only can view the
settings without the right to configure the switch; the admin can configure all the functions of the
switch. The Web management pages contained in this guide are subject to the admin’s login without any
explanation.
Choose the menu Syste m→User Manageme nt→User Config to load the following page.
Figure 4-9 User Config
19
The following entries are displayed on this screen:
Use r Info
Use r Name: Create a name for users’ login.
Access Level: Select the access level to login.
Admin: Admin can edit, m
odify and view all the settings of
different functions.
Guest:
Guest only can view the settings without the right to edit
and modify.
Password: Type a password for users’ login.
Confirm Password: Retype the password.
User Table
Select: Select the desir
ed entry to delete the corresponding user
information. It is multi-optional. The current user information can’
t
be deleted.
User ID, Name and
Access Level:
Displays the current user ID, user name and access level.
Operation: Click the Edit button of the
desired entry, and you can edit the
corresponding user information. After modifying the settings,
please click the Modify
button to make the modification effective.
Access level of the current user information can’t be modified.
4.3 System Tools
The System Tools function, allowing you to manage the configuration file of the switch, can be
implemented on Config Restore , Config Backup, Firmware Upgrade , System Reboot and
System Reset pages.
4.3.1 Config Restore
On this page you can upload a backup configuration file to restore your switch to this previous
configuration.
Choose the menu Syste m→System Tools→Config Restore to load the following page.
Figure 4-10 Config Restore
20
The following entries are displayed on this screen:
Config Restore
Restore Config: Click the Re store Config
button to restore the backup
configuration file. It will take effect after the switch automatically
reboots.
Note:
1. It will take a few minutes to restore the configuration. Please wait without any operation.
2. To avoid any damage, please don’t power down the switch while being restored.
3. After being restored, the current settings of the switch will be lost. Wrong uploaded
configuration file may cause the switch unmanaged.
4.3.2 Config Backup
On this page you can download the current configuration and save it as a file to your computer for
your future configuration restore.
Choose the menu Syste m→System Tools→Config Backup to load the following page.
Figure 4-11 Config Backup
The following entries are displayed on this screen:
Config Backup
Backup Config: Click the Backup Config
button to save the current configuration
as a file to your computer. You are suggested to take this measure
before upgrading.
Note:
It will take a few minutes to backup the configuration. Please wait without any operation.
4.3.3 Firmware Upgrade
The switch system can be upgraded via the Web management page. To upgrade the system is to
get more functions and better performance. Go to http://www.tp-link.com to download the updated
firmware.
21
Choose the menu Syste m→System Tools→Firmware Upgrade to load the following page.
Figure 4-12 Firmware Upgrade
Note:
1. Don’t interrupt the upgrade.
2. Please select the proper software version matching with your hardware to upgrade.
3. To avoid damage, please don't turn off the device while upgrading.
4. After upgrading, the device will reboot automatically.
5. You are suggested to backup the configuration before upgrading.
4.3.4 System Reboot
On this page you can reboot the switch and return to the login page. Please save the current
configuration before rebooting to avoid losing the configuration unsaved
Choose the menu Syste m→System Tools→System Reboot to load the following page.
Figure 4-13 System Reboot
Note:
To avoid damage, please don't turn off the device while rebooting.
4.3.5 System Reset
On this page you can reset the switch to the default. All the settings will be cleared after the switch
is reset.
22
Choose the menu Syste m→System Tools→System Reset to load the following page.
Figure 4-14 System Reset
Note:
After the system is reset, the switch will be reset to the default and all the settings will be cleared.
4.4 Access Security
Access Security provides different security measures for the remote login so as to enhance the
configuration management security. It can be implemented on Access Control page.
4.4.1 Access Control
On this page you can control the users logging on to the Web management page to enhance the
configuration management security. The definitions of Admin and Guest refer to 4.2 User
Management.
Choose the menu Syste m→Access Security→Access Control to load the following page.
Figure 4-15 Access Control
23
The following entries are displayed on this screen:
Access Control Config
Control Mode: Select the contr
ol mode for users to log on to the Web
management page.
Disable
：
Disable the access control function.
IP-based: Select this option to limit the IP-
range of the users
for login.
M AC-based: Select this option to limit the MAC address
of the
users for login.
Port-based: Select this option to limit the ports for login.
IP Address & Mask These fields can be available for configuration only when IP-
based
mode is selected. Only the users within the IP-
range you set here
are allowed for login.
M AC Ad d r e ss: The field can be available for configuration only when MAC-
based
mode is selected. Only the user with this MAC address
you set
here are allowed for login.
Port: The field can be available for configuration only when Port-
based
mode is selected. Only the users c
onnected to these ports you set
here are allowed for login.
Session Config
Session Timeout:
If you do nothing with the Web management page within the
timeout time, the system will log out automatically. If you want to
reconfigure, please login again.
Access User Number
Number Control: Select Enable/Disable the Number Control function.
Admin Number:
Enter the maximum number of the users logging on to the Web
management page as Admin.
Guest Number: Enter the maximum number of the users logging on to the Web
management page as Guest.
4.4.2 SSL Config
SSL (Secure Sockets Layer), a security protocol, is to provide a secure connection for the
application layer protocol (e.g. HTTP) communication based on TCP. SSL is widely used to secure
the data transmission between the Web browser and servers. It is mainly applied through
ecommerce and online banking.
SSL mainly provides the following services:
1. Authenticate the users and the servers based on the certificates to ensure the data are
transmitted to the correct users and servers;
2. Encrypt the data transmission to prevent the data being intercepted;
3. Maintain the integrality of the data to prevent the data being altered in the transmission.
Adopting asymmetrical encryption technology, SSL uses key pair to encrypt/decrypt information. A
key pair refers to a public key (contained in the certificate) and its corresponding private key. By
24
default the switch has a certificate (self-signed certificate) and a corresponding private key. The
Certificate/Key Download function enables the user to replace the default key pair.
After SSL is effective, you can log on to the Web management page via https://192.168.0.1. For
the first time you use HTTPS connection to log into the switch with the default certificate, you will
be prompted that “The security certificate presented by this website was not issued by a trusted
certificate authority” or “Certificate Errors”. Please add this certificate to trusted certificates or
continue to this website.
On this page you can configure the SSL function.
Choose the menu Syste m→Access Security→SSL Config to load the following page.
Figure 4-16 SSL Config
The following entries are displayed on this screen:
Global Config
SSL: Select Enable/Disable the SSL function on the switch.
Certificate Download
Certificate File:
Select the desired certificate to download to the switch. The
certificate must be BASE64 encoded.
Key Download
Key File: Select the desired SSL key to downloa
d to the switch. The key
must be BASE64 encoded.
Note:
1. The SSL certificate and key downloaded must match each other; otherwise the HTTPS
connection will not work.
2. The SSL certificate and key downloaded will not take effect until the switch is rebooted.
3. To establish a secured connection using https, please enter https:// into the URL field of the
browser.
25
4. It may take more time for https connection than that for http connection, because https
connection involves authentication, encryption and decryption etc.
4.4.3 SSH Config
As stipulated by IFTF (Internet Engineering Task Force), SSH (Secure Shell) is a security protocol
established on application and transport layers. SSH-encrypted-connection is similar to a telnet
connection, but essentially the old telnet remote management method is not safe, because the
password and data transmitted with plain-text can be easily intercepted. SSH can provide
information security and powerful authentication when you log on to the switch remotely through
an insecure network environment. It can encrypt all the transmission data and prevent the
information in a remote management being leaked.
Comprising server and client, SSH has two versions, V1 and V2 which are not compatible with
each other. In the communication, SSH server and client can auto-negotiate the SSH version and
the encryption algorithm. After getting a successful negotiation, the client sends authentication
request to the server for login, and then the two can communicate with each other after successful
authentication. This switch supports SSH server and you can log on to the switch via SSH
connection using SSH client software.
SSH key can be downloaded into the switch. If the key is successfully downloaded, the certificate
authentication will be preferred for SSH access to the switch.
Choose the menu Syste m→Access Security→SSH Config to load the following page.
Figure 4-17 SSH Config
The following entries are displayed on this screen:
Global Config
SSH: Select Enable/Disable SSH function.
Protocol V1: Select Enable/Disable SSH V1 to be the supported protocol.
Protocol V2: Select Enable/Disable SSH V2 to be the supported protocol.
26
Idle Timeout:
Specify the idle timeout time. The system will automatically
release the connec
tion when the time is up. The default time is
120 seconds.
Max Connect:
Specify the maximum number of the connections to the SSH
server. No new connection will be established when the number
of the connections reaches the maximum number you set. The
default value is 5.
Key Download
Ke y Type : Select the type of SSH k
ey to download. The switch supports
three types: SSH-1 RSA, SSH-2 RSA and SSH-2 DSA.
Key File: Select the desired key file to download.
Download: Click the Download button to down the desire
d key file to the
switch.
Note:
1. Please ensure the key length of the downloaded file is in the range of 512 to 3072 bits.
2. After the key file is downloaded, the user’s original key of the same type will be replaced. The
wrong uploaded file will result in the SSH access to the switch via Password authentication.
Application Example 1 for SSH:
Network Requirements
1. Log on to the switch via password authentication using SSH and the SSH function is enabled
on the switch.
2. PuTTY client software is recommended.
27
Configuration Procedure
1. Open the software to log on to the interface of PuTTY. Enter the IP address of the switch into
Host Name field; keep the default value 22 in the Port field; select SSH as the Connection
type.
2. Click the Ope n button in the above figure to log on to the switch. Enter the login user name and
password, and then you can continue to configure the switch.
Application Example 2 for SSH:
Network Requirements
1. Log on to the switch via password authentication using SSH and the SSH function is enabled
on the switch.
2. PuTTY client software is recommended.
28
Configuration Procedure
1. Select the key type and key length, and generate SSH key.
Note:
1. The key length is in the range of 512 to 3072 bits.
2. During the key generation, randomly moving the mouse quickly can accelerate the key
generation.
29
2. After the key is successfully generated, please save the public key and private key to the
computer.
3. On the Web management page of the switch, download the public key file saved in the
computer to the switch.
Note:
1. The key type should accord with the type of the key file.
2. The SSH key downloading cannot be interrupted.
30
4. After the public key and private key are downloaded, please log on to the interface of PuTTY
and enter the IP address for login.
31
5. Click Aut h under the SSH menu in the left Category list, and click Browse to download the
private key file to SSH client software and click Open.
After successful authentication, please enter the login user name. If you log on to the switch
without entering password, it indicates that the key has been successfully downloaded.
Return to CONTENTS
32
Chapter 5 Switching
Switching module is used to configure the basic functions of the switch, including four submenus:
Port, LAG, Traffic Monitor and M AC Addr e ss.
5.1 Port
The Port function, allowing you to configure the basic features for the port, is implemented on the
Port Config, Port Mirror, Port Se curity, Port Isolation and Loopback Detection pages.
5.1.1 Port Config
On this page, you can configure the basic parameters for the ports. When the port is disabled, the
packets on the port will be discarded. Disabling the port which is vacant for a long time can reduce
the power consumption effectively. And you can enable the port when it is in need.
The parameters will affect the working mode of the port, please set the parameters appropriate to
your needs.
Choose the menu Switching→Port→Port Config to load the following page.
Figure 5-1Port Config
The following entries are displayed on this screen：
Port Config
Port Sele ct
: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Select
: Select the desired port for configuration. It is multi-optional.
Port
: Displays the port number.
33
Description
: Give a description to the port for identification.
Status
: Allows you to Enable/Disable the port. When Enable is
selected,
the port can forward the packets normally.
Speed and Duplex
:
Select the Speed and Duplex mode for the port. The device
connected to the switch should be in the same Speed and
Duplex mode with the switch. When “Auto” is selected, the
Speed and Duplex mode will be determined by auto-
negotiation.
For the SFP port, this switch does not support auto-
negotiation.
Flow Control
:
Allows you to Enable/Disable the Flow Control feature. When
Flow Control is enabled, the switch can synchronize the speed
with its peer to avoid the packet loss caused by congestion.
LAG
: Displays the LAG number which the port belongs to.
Note:
1. The switch cannot be managed through the disabled port. Please enable the port which is
used to manage the switch.
2. The parameters of the port members in a LAG should be set as the same.
3. When using the SFP port with a 100M module or a gigabit module, you need to configure its
corresponding Speed and Duplex mode. For 100M module, please select 100MFD while
select 1000MFD for gigabit module. By default, the Speed and Duple x mode of SFP port is
1000MFD.
5.1.2 Port Mirror
Port Mirror, the packets obtaining technology, functions to forward copies of packets from
one/multiple ports (mirrored port) to a specific port (mirroring port). Usually, the mirroring port is
connected to a data diagnose device, which is used to analyze the mirrored packets for monitoring
and troubleshooting the network.
Choose the menu Switching→Port→Port Mirror to load the following page.
Figure 5-2 Mirror Group List
34
The following entries are displayed on this screen.
Mirror Group List
Group: Displays the mirror group number.
Mirroring: Displays the mirroring port number.
Mode: Displays the mirror mode. The value will be "Ingress" or "Egress".
Mirrored Port: Displays the mirrored ports.
Operation: Click Edit to configure the mirror group.
Click Edit to display the following figure.
Figure 5-3 Port Mirror Config
The following entries are displayed on this screen:
Mirror Group
Number: Select the mirror group number you want to configure.
Mirroring Port
Mirroring Port: Select the mirroring port number.
35
Mirrored Port
Port Sele ct: Click the Select button to quick-select the corresponding port based
on the port number you entered.
Select: Select the desired port as a mirrored port. It is multi-optional.
Port: Displays the port number.
Ingress:
Select Enable/Disable the Ingress feature. When the Ingress is
enabled, the inco
ming packets received by the mirrored port will be
copied to the mirroring port.
Egress:
Select Enable/Disable the Egress feature. When the Egress is
enabled, the outgoing packets sent by the mirrored port will be
copied to the mirroring port.
LAG: Displ
ays the LAG number which the port belongs to. The LAG
member cannot be selected as the mirrored port or mirroring port.
Note:
1. The LAG member cannot be selected as the mirrored port or mirroring port.
2. A port cannot be set as the mirrored port and the mirroring port simultaneously.
3. The Port Mirror function can take effect span the multiple VLANs.
5.1.3 Port Security
MAC Address Table maintains the mapping relationship between the port and the MAC address of
the connected device, which is the base of the packet forwarding. The capacity of MAC Address
Table is fixed. MAC Address Attack is the attack method that the attacker takes to obtain the
network information illegally. The attacker uses tools to generate the cheating MAC address and
quickly occupy the MAC Address Table. When the MAC Address Table is full, the switch will
broadcast the packets to all the ports. At this moment, the attacker can obtain the network
information via various sniffers and attacks. When the MAC Address Table is full, the packets
traffic will flood to all the ports, which results in overload, lower speed, packets drop and even
breakdown of the system.
Port Security is to protect the switch from the malicious MAC Address Attack by limiting the
maximum number of MAC addresses that can be learned on the port. The port with Port Security
feature enabled will learn the MAC address dynamically. When the learned MAC address number
reaches the maximum, the port will stop learning. Thereafter, the other devices with the MAC
address unlearned cannot access to the network via this port.
36
Choose the menu Switching→Port→Port Se curity to load the following page.
Figure 5-4 Port Security
The following entries are displayed on this screen:
Port Security
Select
: Select the desired port for Port Security configuration. It is
multi-optional.
Port
: Displays the port number.
Max Learned MAC
:
Specify the maximum number of MAC addresses that can be
learned on the port.
Le arne d Num
:
Displays the number of MAC addresses that have been learned
on the port.
Learn Mode
: Select the Learn Mode for the port.
• Dynamic:
When Dynamic mode is selected, the learned
MAC address will be deleted automatically after the aging
time.
• Static:
When Static mode is selected, the learned MAC
address will be out of the influence of the aging time and
can only be deleted manually. The learned entries will be
cleared after the switch is rebooted.
• Pe rmane nt:
When Permanent mode is selected, the
learned MAC address will be out of the influence of the
aging time and can only be deleted manually. The learned
entries will be saved even the switch is rebooted.
Status
: Select Enable/Disable the Port Security feature for the port.
37
Note:
The Port Security function is disabled for the LAG port member. Only the port is removed from the
LAG, will the Port Security function be available for the port.
5.1.4 Port Isolation
Port Isolation provides a method of restricting traffic flow to improve the network security by
forbidding the port to forward packets to the ports that are not on its forward portlist.
Choose the menu Switching→Port→Port Isolation to load the following page.
Figure 5-5 Port Isolation
The following entries are displayed on this screen:
Port Isolation Config
From Port/To Port: Select the port number in this range to set their forward list.
Forward Portlist: Select the port that to be forwarded to.
Port Isolation List
Port: Display the port number.
38
Forward Portlist: Display the forwardlist.
5.1.5 Loopback Detection
With loopback detection feature enabled, the switch can detect loops using loopback detection
packets. When a loop is detected, the switch will display an alert or further block the corresponding
port according to the port configuration.
Choose the menu Switching→Port→Loopback De tection to load the following page.
Figure 5-6 Loopback Detection Config
The following entries are displayed on this screen:
Global Config
Loopback
Detection
Status:
Here you can enable or disable loopback detection function
globally.
Detection Interval: Set a loopback d
etection interval between 1 and 1000 seconds.
By default, it’s 30 seconds.
Automatic Recovery
Time :
Time allowed for automatic recovery when a loopback is detected.
It can be set as integral multiple of detection interval.
We b Re fresh Status: Here you can enable or disable web automatic refresh.
39
Web Refresh Interval
: Set a web refresh interval between 3 and 100 seconds. By default,
it’s 3 seconds.
Port Config
Port Sele ct: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Select: Select the desired port for loopback d
etection configuration. It is
multi-optional.
Port: Displays the port number.
Status: Enable or disable loopback detection function for the port.
Operation Mode: Select the mode how the switch processes the detected loops.
• Alert: When a loop is detected, displays an alert.
• Port based: When a loopback is detected, displays an alert
and blocks the port.
Recovery Mode: Select the mode how the blocked port recovers to normal status.
• Auto: Block status can be automatically removed after
recovery time.
• Manual: Block status only can be removed manually.
Loop Status: Displays the port status whether a loopback is detected.
Block Status: Displays the port status about block or unblock.
LAG: Displays the LAG number the port belongs to.
Manual Recover: Manually remove the block status of selected ports.
Note:
1. Recovery Mode is not selectable when Alert is chosen in Operation Mode.
2. Loopback Detection must coordinate with storm control.
5.2 LAG
LAG (Link Aggregation Group) is to combine a number of ports together to make a single
high-bandwidth data path, so as to implement the traffic load sharing among the member ports in
the group and to enhance the connection reliability.
For the member ports in an aggregation group, their basic configuration must be the same. The
basic configuration includes STP, QoS, VLAN, port attributes, M AC Addre ss Le arning mode
and other associated settings. The further explains are following:
If the ports, which are enabled for the 802.1Q VLAN, STP, QoS and Port Configuration
(Speed and Flow Control), are in a LAG, their configurations should be the same.
The ports, which are enabled for the half-duplex, Port Se curity, Port Mirror and M AC
Address Filtering, cannot be added to the LAG.
If the LAG is needed, you are suggested to configure the LAG function here before configuring the
other functions for the member ports.
40
Tips:
1. Calculate the bandwidth for a LAG: If a LAG consists of the four ports in the speed of
1000Mbps Full Duplex, the whole bandwidth of the LAG is up to 8000Mbps (2000Mbps * 4)
because the bandwidth of each member port is 2000Mbps counting the up-linked speed of
1000Mbps and the down-linked speed of 1000Mbps.
2. The traffic load of the LAG will be balanced among the ports according to the Aggregate
Arithmetic. If the connections of one or several ports are broken, the traffic of these ports will
be transmitted on the normal ports, so as to guarantee the connection reliability.
The LAG function is implemented on the LAG Table, Static LAG and LACP Config configuration
pages.
5.2.1 LAG Table
On this page, you can view the information of the current LAG of the switch.
Choose the menu Switching→LAG→LAG Table to load the following page.
Figure 5-7 LAG Table
The following entries are displayed on this screen:
Global Config
Hash Algorithm:
Select the applied scope of Aggregate Arithmetic, which
results in choosing a port to transfer the packets.
• SRC MAC + DST M AC:
When this option is selected, the
Aggregate Arithmetic will apply to the source and destination
MAC addresses of the packets.
• SRC IP + DST IP:
When this option is selected, the
Aggregate A
rithmetic will apply to the source and destination
IP addresses of the packets.
LAG Table
Select
: Select the desired LAG. It is multi-optional.
Group Number
: Displays the LAG number here.
Description
: Displays the description of LAG.
M e mber
: Displays the LAG member.
41
Operation
: Allows you to view or modify the information for each LAG.
• Edit: Click to modify the settings of the LAG.
• Detail: Click to get the information of the LAG.
Click the Detail button for the detailed information of your selected LAG.
Figure 5-8 Detailed Information
5.2.2 Static LAG
On this page, you can manually configure the LAG.
Choose the menu Switching→LAG→Static LAG to load the following page.
Figure 5-9 Manually Config
42
The following entries are displayed on this screen:
LAG Config
Group Number
: Select a Group Number for the LAG.
Description
: Displays the description of the LAG.
Member Port
Member Port
:
Select the port as the LAG member. Clearing all the ports of
the LAG will delete this LAG.
Tips:
1. The LAG can be deleted by clearing its all member ports.
2. A port can only be added to a LAG. If a port is the member of a LAG, the port number will be
displayed in gray and cannot be selected.
5.2.3 LACP Config
LACP (Link Aggregation Control Protocol) is defined in IEEE802.3ad and enables the dynamic link
aggregation and disaggregation by exchanging LACP packets with its partner. The switch can
dynamically group similarly configured ports into a single logical link, which will highly extend the
bandwidth and flexibly balance the load.
With the LACP feature enabled, the port will notify its partner of the system priority, system MAC,
port priority, port number and operation key (operation key is determined by the physical
properties of the port, upper layer protocol and admin key). The device with higher priority will lead
the aggregation and disaggregation. System priority and system MAC decide the priority of the
device. The smaller the system priority, the higher the priority of the device is. With the same
system priority, the device owning the smaller system MAC has the higher priority. The device with
the higher priority will choose the ports to be aggregated based on the port priority, port number
and operation key. Only the ports with the same operation key can be selected into the same
aggregation group. In an aggregation group, the port with smaller port priority will be considered
as the preferred one. If the two port priorities are equal, the port with smaller port number is
preferred. After an aggregation group is established, the selected ports can be aggregated
together as one port to transmit packets.
On this page, you can configure the LACP feature of the switch.
43
Choose the menu Switching→LAG→LACP Config to load the following page.
Figure 5-10 LACP Config
The following entries are displayed on this screen:
Global Config
Syste m Priority:
Specify the system priority for the switch. The system
priority and
MAC address constitute the system identification (ID). A lower system
priority value indicates a higher system priority. When exchanging
information between systems, the system with higher priority
determines which link aggregation a link bel
ongs to, and the system
with lower priority adds the proper links to the link aggregation
according to the selection of its partner.
LACP Config
Port Sele ct:
Click the Select button to quick-
select the corresponding port based
on the port number you entered.
Select:
Select the desired port for LACP configuration. It is multi-optional.
Port:
Displays the port number.
Admin Key:
Specify an admin k
ey for the port. The member ports in a dynamic
aggregation group must have the same admin key.
Port Priority
:
Specify a Port Priority for the port. This value determines the priority
of the port to be selected as the dynamic aggregation group
44
member. The port with smaller Port Priority will be considered as the
preferred one. If the two port priorities are equal
; the port with
smaller port number is preferred.
Mode:
Specify LACP mode for your selected port.
Status:
Enable/Disable the LACP feature for your selected port.
LAG:
Displays the LAG number which the port belongs to.
5.3 Traffic Monitor
The Traffic Monitor function, monitoring the traffic of each port, is implemented on the Tr a ff i c
Summary and Traffic Statistics pages.
5.3.1 Traffic Summary
Traffic Summary screen displays the traffic information of each port, which facilitates you to
monitor the traffic and analyze the network abnormity.
Choose the menu Switching→Traffic Monitor→Traffic Summary to load the following page.
Figure 5-11 Traffic Summary
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh
:
Allows you to Enable/Disable refreshing the Traffic Summary
automatically.
Refresh Rate
: Enter a value in seconds to specify the refresh interval.
45
Traffic Summary
Port Sele ct
: Click the Select button to quick-select the corresponding port
based
on the port number you entered.
Port
: Displays the port number.
Packets Rx
:
Displays the number of packets received on the port. The error
packets are not counted in.
Packets Tx
: Displays the number of packets transmitted on the port.
Octets R
x:
Displays the number of octets received on the port. The error octets
are counted in.
Octets Tx
: Displays the number of octets transmitted on the port.
Statistics
: Click the Statistics
button to view the detailed traffic statistics of the
port.
5.3.2 Traffic Statistics
Traffic Statistics screen displays the detailed traffic information of each port, which facilitates you to
monitor the traffic and locate faults promptly.
Choose the menu Switching→Traffic Monitor→Traffic Statistics to load the following page.
Figure 5-12 Traffic Statistics
46
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh
: Allows you to Enable/Disable ref
reshing the Traffic Summary
automatically.
Refresh Rate
: Enter a value in seconds to specify the refresh interval.
Statistics
Port
: Enter a port number and click the Select
button to view the traffic
statistics of the corresponding port.
Received
: Displays the details of the packets received on the port.
Sent
: Displays the details of the packets transmitted on the port.
Broadcast
:
Displays the number of good broadcast packets received or
transmitted on the port. The error frames are not counted in.
Mu
lticast:
Displays the number of good multicast packets received or
transmitted on the port. The error frames are not counted in.
Unicast
:
Displays the number of good unicast packets received or
transmitted on the port. The error frames are not counted in.
Alignment Errors
:
Displays the number of the received packets that have a bad
Frame Check Sequence (FCS) with a non-
integral octet
(Alignment Error). The length of the packet is
from 64 bytes to
maximal bytes of the jumbo frame (usually 9216 bytes).
Und
ersizePkts:
Displays the number of the received packets (excluding error
packets) that are less than 64 bytes long.
Pkts64Octets
:
Displays the number of the received packets (including error
packets) that are 64 bytes long.
Pkts65to127Octets
: Displays th
e number of the received packets (including error
packets) that are between 65 and 127 bytes long.
Pkts128to255Octets
:
Displays the number of the received packets (including error
packets) that are between 128 and 255 bytes long.
Pkts256to511Octets
: Disp
lays the number of the received packets (including error
packets) that are between 256 and 511 bytes long.
Pkts512to1023Octets
:
Displays the number of the received packets (including error
packets) that are between 512 and 1023 bytes long.
Pkts
Over1023Octets:
Displays the number of the received packets (including error
packets) that the size of the packets is from 1024 bytes to 1518
bytes (1522 bytes if the packets have VLAN-tag fields).
Collisions
: Displays the number of collisions experienced by a port
during
packet transmissions.
5.4 MAC Address
The main function of the switch is forwarding the packets to the correct ports based on the
destination MAC address of the packets. Address Table contains the port-based MAC address
information, which is the base for the switch to forward packets quickly. The entries in the Address
Table can be updated by auto-learning or configured manually. Most the entries are generated and
47
updated by auto-learning. In the stable networks, the static MAC address entries can facilitate the
switch to reduce broadcast packets and enhance the efficiency of packets forwarding remarkably.
The address filtering feature allows the switch to filter the undesired packets and forbid its
forwarding so as to improve the network security.
The types and the features of the MAC Address Table are listed as the following:
Typ e Configuration
Way Aging out
Being kept after
reboot
(if the configuration
is saved)
Relationship between the
bound MAC address and
the port
Static
Address Table
Manually
configuring
No Ye s
The bound MAC address
cannot
be learned by the
other ports in the same
VLAN.
Dynamic
Address Table
Automatically
learning
Yes No
The bound MAC address
can be learned by the other
ports in the same VLAN.
Filtering
Address Table
Manually
configuring
No Ye s -
Table 5-1 Types and features of Address Table
This function includes four submenus: Address Table, Static Address, Dynamic Address and
Filtering Address.
5.4.1 Address Table
On this page, you can view all the information of the Address Table.
Choose the menu Switching→M AC Ad dr e ss→Address Table to load the following page.
Figure 5-13 Address Table
The following entries are displayed on this screen:
Search Option
M AC Ad d r e ss
: Enter the MAC address of your desired entry.
48
VLAN ID
: Enter the VLAN ID of your desired entry.
Port
: Select the corresponding port number of your desired entry.
Typ e
: Select the type of your desired entry.
All:
This option allows the address table to display all the
address entries.
Static:
This option allows the address table to display the static
address entries only.
Dynamic:
This option allows the address table to display the
dynamic address entries only.
Filtering:
This option allows the address table to display the
filtering address entries only.
Address Table
M AC Ad d r e ss
: Displays the MAC address learned by the switch.
VLAN ID
: Displays the corresponding VLAN ID of the MAC address.
Port
: Displays the corresponding Port number of the MAC address.
Typ e
: Displays the Type of the MAC address.
Aging Status
: Displays the Aging status of the MAC address.
5.4.2 Static Address
The static address table maintains the static address entries which can be added or removed
manually, independent of the aging time. In the stable networks, the static MAC address entries
can facilitate the switch to reduce broadcast packets and remarkably enhance the efficiency of
packets forwarding without learning the address. The static MAC address learned by the port with
Port Security enabled in the static learning mode will be displayed in the Static Address Table.
Choose the menu Switching→M AC Addr e ss→Static Address to load the following page.
Figure 5-14 Static Address
49
The following entries are displayed on this screen:
Create Static Address
M AC Ad d r e ss
: Enter the static MAC address to be bound.
VLAN ID
: Enter the corresponding VLAN ID of the MAC address.
Port
: Select a port from the pull-down list to be bound.
Search Option
Search Option
: Select a Search Option from the pull-down list and click the Se arch
button to find your desired entry in the Static Address Table.
• MAC: Enter the MAC address of your desired entry.
• VLAN ID: Enter the VLAN ID number of your desired entry.
• Port: Enter the Port number of your desired entry.
Static Address Table
Select
: Select the entry to delete or modif
y the corresponding port number. It
is multi-optional.
M AC Ad d r e ss
: Displays the static MAC address.
VLAN ID
: Displays the corresponding VLAN ID of the MAC address.
Port
:
Displays the corresponding Port number of the MAC address. Here
you can modify the
port number to which the MAC address is bound.
The new port should be in the same VLAN.
Typ e
: Displays the Type of the MAC address.
Aging Status
: Displays the Aging Status of the MAC address.
Note :
1. If the corresponding port number of the MAC address is not correct, or the connected port (or
the device) has been changed, the switch cannot be forward the packets correctly. Please
reset the static address entry appropriately.
2. If the MAC address of a device has been added to the Static Address Table, connecting the
device to another port will cause its address not to be recognized dynamically by the switch.
Therefore, please ensure the entries in the Static Address Table are correct and valid.
3. The MAC address in the Static Address Table cannot be added to the Filtering Address Table
or bound to a port dynamically.
5.4.3 Dynamic Address
The dynamic address can be generated by the auto-learning mechanism of the switch. The
Dynamic Address Table can update automatically by auto-learning or the MAC address aging out
mechanism.
To fully utilize the MAC address table, which has a limited capacity, the switch adopts an aging
mechanism for updating the table. That is, the switch removes the MAC address entries related to
a network device if no packet is received from the device within the aging time.
On this page, you can configure the dynamic MAC address entry.
50
Choose the menu Switching→M AC Addr e ss→Dynamic Address to load the following page.
Figure 5-15 Dynamic Address
The following entries are displayed on this screen:
Aging Config
Auto Aging
: Allows you to Enable/Disable the Auto Aging feature.
Aging Time
: Enter the Aging Time for the dynamic address.
Search Option
Search Option
: Select a Search Option from the pull-down list and click the
Search
button to find your desired entry in the Dynamic Address Table.
• MAC: Enter the MAC address of your desired entry.
• VLAN ID: Enter the VLAN ID number of your desired entry.
• Port: Enter the Port number of your desired entry.
• LAG ID: Enter the LAG ID of your desired entry.
Dynamic Address Table
Select
:
Select the entry to delete the dynamic address or to bind the MAC
address to the corresponding port statically. It is multi-optional.
M AC Ad d r e ss
: Displays the dynamic MAC address.
VLAN ID
: Displays the corresponding VLAN ID of the MAC address.
Port
: Displays the corresponding port number of the MAC address.
Typ e
: Displays the Type of the MAC address.
Aging Status
: Displays the Aging Status of the MAC address.
51
Bind
: Click the Bind
button to bind the MAC address of your selected entry
to the corresponding port statically.
Tips:
Setting aging time properly helps implement effective MAC address aging. The aging time that is
too long or too short results decreases the performance of the switch. If the aging time is too long,
excessive invalid MAC address entries maintained by the switch may fill up the MAC address table.
This prevents the MAC address table from updating with network changes in time. If the aging time
is too short, the switch may remove valid MAC address entries. This decreases the forwarding
performance of the switch. It is recommended to keep the default value.
5.4.4 Filtering Address
The filtering address is to forbid the undesired packets to be forwarded. The filtering address can
be added or removed manually, independent of the aging time. The filtering MAC address allows
the switch to filter the packets which includes this MAC address as the source address or
destination address, so as to guarantee the network security. The filtering MAC address entries
act on all the ports in the corresponding VLAN.
Choose the menu Switching→M AC Addr e ss→Filtering Address to load the following page.
Figure 5-16 Filtering Address
The following entries are displayed on this screen:
Create Filtering Address
M AC Ad d r e ss
: Enter the MAC address to be filtered.
VLAN ID
: Enter the corresponding VLAN ID of the MAC address.
Search Option
Search Option: Select a Search Option from the pull-down list and click the Se arch
button to find your desired entry in the Filtering Address Table.
• M AC: Enter the MAC address of your desired entry.
52
• VLAN ID: Enter the VLAN ID number of your desired entry.
Filtering Address Table
Select: Select the entry t
o delete the corresponding filtering address. It is
multi-optional.
M AC Ad d r e ss: Displays the filtering MAC address.
VLAN ID: Displays the corresponding VLAN ID.
Port: Here the symbol “__” indicates no specified port.
Typ e : Displays the Type of the MAC address.
Aging Status: Displays the Aging Status of the MAC address.
Note:
The MAC address in the Filtering Address Table cannot be added to the Static Address Table or
bound to a port dynamically.
5.5 DHCP Filtering
Nowadays, the network is getting larger and more complicated. The amount of the PCs always
exceeds that of the assigned IP addresses. The wireless network and the laptops are widely used
and the locations of the PCs are always changed. Therefore, the corresponding IP address of the
PC should be updated with a few configurations. DHCP (Dynamic Host Configuration Protocol)
functions to solve the above mentioned problems.
However, during the working process of DHCP, generally there is no authentication mechanism
between Server and Client. If there are several DHCP servers in the network, network confusion
and security problem will happen. To protect the switch from being attacked by illegal DHCP
servers, you can configure the desired ports as trusted ports and only the clients connected to the
trusted ports can receive DHCP packets from DHCP severs. Here the DHCP Filtering function
performs to monitor the process of hosts obtaining IP addresses from DHCP servers.
DHCP Working Principle
DHCP works via the “Client/Server” communication mode. The Client applies to the Server for
configuration. The Server assigns the configuration information, such as the IP address, to the
Client, so as to reach a dynamic employ of the network source. A Server can assign IP address for
several Clients, which is illustrated in the following figure.
53
Figure 5-17 Network diagram of DHCP
For different DHCP clients, DHCP server provides three IP address assigning methods:
(1) Manually assign the IP address: Allows the administrator to bind the static IP address to a
specific client (e.g.: WWW Server) via the DHCP server.
(2) Automatically assign the IP address: DHCP server assigns the IP address without an
expiry time limitation to the clients.
(3) Dynamically assign the IP address: DHCP server assigns the IP address with an expiry
time. When the time for the IP address expired, the client should apply for a new one.
Most clients obtain IP addresses dynamically, which is illustrated in the following figure.
Figure 5-18 Interaction between a DHCP client and a DHCP server
(1) DHCP-DISCOVER Stage: The Client broadcasts the DHCP-DISCOVER packet to find
the DHCP server.
(2) DHCP-OFFER Stage : Upon receiving the DHCP-DISCOVER packet, the DHCP server
selects an IP address from the IP pool according to the assigning priority of the IP
addresses and replies to the client with DHCP-OFFER packet carrying the IP address and
other information.
(3) DHCP-REQUEST Stage : In the situation that there are several DHCP servers sending the
DHC P-OFFER packets, the client will only respond to the first received DHCP-OFFER
54
packet and broadcast the DHCP-REQUEST packet which includes the assigned IP
address of the DHCP-OFFER packet.
(4) DHCP-ACK Stage: Since the DHCP-REQUEST packet is broadcasted, all DHCP servers
on the network segment can receive it. However, only the requested server processes the
request. If the DHCP server acknowledges assigning this IP address to the client, it will
send the DHCP-ACK packet back to the client. Otherwise, the Server will send the
DHCP-NAK packet to refuse assigning this IP address to the client.
DHCP Cheating Attack
During the working process of DHCP, generally there is no authentication mechanism between
Server and Client. If there are several DHCP servers in the network, network confusion and
security problem will happen. The common cases incurring the illegal DHCP servers are the
following two:
(1) It’s common that the illegal DHCP server is manually configured by the user by mistake.
(2) Hacker exhausted the IP addresses of the normal DHCP server and then pretended to be
a legal DHCP server to assign the IP addresses and the other parameters to Clients. For
example, hacker used the pretended DHCP server to assign a modified DNS server
address to users so as to induce the users to the evil financial website or electronic trading
website and cheat the users of their accounts and passwords. The following figure
illustrates the DHCP Cheating Attack implementation procedure.
Figure 5-19 DHCP Cheating Attack Implementation Procedure
DHCP Filtering feature allows only the trusted ports to forward DHCP packets from DHCP servers
and thereby ensures that users get proper IP addresses. DHCP Filtering is to monitor the process
of hosts obtaining the IP addresses from DHCP servers, and record the IP address, MAC address,
VLAN and the connected Port number of the Host for automatic binding. DHCP Filtering feature
prevents the network from the DHCP Server Cheating Attack by discarding the DHCP packets on
the distrusted port, so as to enhance the network security.
55
Choose the menu Switching → DHCP Filtering to load the following page.
Figure 5-20 DHCP Filtering
The following entries are displayed on this screen:
DHCP Filtering
DHCP Filtering:
E
nable/Disable the DHCP Filtering function globally.
Trusted Port
Here you can select the desired port(s) to be Trusted Port(s). Only the Trusted Port(s) can
forward DHCP packets from DHCP Servers. Click All button to select all ports. Click Clear
button to select none.
Return to CONTENTS
56
Chapter 6 VLAN
The traditional Ethernet is a data network communication technology based on CSMA/CD (Carrier
Sense Multiple Access/Collision Detect) via shared communication medium. Through the
traditional Ethernet, the overfull hosts in LAN will result in serious collision, flooding broadcasts,
poor performance or even breakdown of the Internet. Though connecting the LANs through
switches can avoid the serious collision, the flooding broadcasts cannot be prevented, which will
occupy plenty of bandwidth resources, causing potential serious security problems.
A Virtual Local Area Network (VLAN) is a network topology configured according to a logical
scheme rather than the physical layout. The VLAN technology is developed for switches to control
broadcast in LANs. By creating VLANs in a physical LAN, you can divide the LAN into multiple
logical LANs, each of which has a broadcast domain of its own. Hosts in the same VLAN
communicate with one another as if they are in a LAN. However, hosts in different VLANs cannot
communicate with one another directly. Therefore, broadcast packets are limited in a VLAN. Hosts
in the same VLAN communicate with one another via Ethernet whereas hosts in different VLANs
communicate with one another through the Internet devices such as router, the Layer 3 switch, etc.
The following figure illustrates a VLAN implementation.
Figure 6-1 VLAN implementation
Compared with the traditional Ethernet, VLAN enjoys the following advantages.
(1) Broadcasts are confined to VLANs. This decreases bandwidth utilization and improves
network performance.
(2) Network security is improved. VLANs cannot communicate with one another directly. That
is, a host in a VLAN cannot access resources in another VLAN directly, unless routers or
Layer 3 switches are used.
(3) Network configuration workload for the host is reduced. VLAN can be used to group
specific hosts. When the physical position of a host changes within the range of the VLAN,
you do not need to change its network configuration.
A VLAN can span across multiple switches, or even routers. This enables hosts in a VLAN to be
dispersed in a looser way. That is, hosts in a VLAN can belong to different physical network
segments. This switch supports 802.1Q VLAN to classify VLANs. VLAN tags in the packets are
necessary for the switch to identify packets of different VLANs.
57
6.1 802.1Q VLAN
VLAN tags in the packets are necessary for the switch to identify packets of different VLANs. The
switch works at the data link layer in OSI model and it can identify the data link layer encapsulation
of the packet only, so you can add the VLAN tag field into the data link layer encapsulation for
identification.
In 1999, IEEE issues the IEEE 802.1Q protocol to standardize VLAN implementation, defining the
structure of VLAN-tagged packets. IEEE 802.1Q protocol defines that a 4-byte VLAN tag is
encapsulated after the destination MAC address and source MAC address to show the information
about VLAN.
As shown in the following figure, a VLAN tag contains four fields, including TPID (Tag Protocol
Identifier), Priority, CFI (Canonical Format Indicator), and VLAN ID.
Figure 6-2 Format of VLAN Tag
(1) TPID: TPID is a 16-bit field, indicating that this data frame is VLAN-tagged. By default, it is
0x8100 in this switch.
(2) Priority: Priority is a 3-bit field, referring to 802.1p priority. Refer to section “QoS & QoS
profile” for details.
(3) CFI: CFI is a 1-bit field, indicating whether the MAC address is encapsulated in the
standard format in different transmission media. This field is not described in detail in this
chapter.
(4) VLA N ID: VL A N ID is a 12-bit field, indicating the ID of the VLAN to which this packet
belongs. It is in the range of 0 to 4,095. Generally, 0 and 4,095 is not used, so the field is in
the range of 1 to 4,094.
VLAN ID identifies the VLAN to which a packet belongs. When the switch receives an
un-VLAN-tagged packet, it will encapsulate a VLAN tag with the default VLAN ID of the inbound
port for the packet, and the packet will be assigned to the default VLAN of the inbound port for
transmission.
In this User Guide, the tagged packet refers to the packet with VLAN tag whereas the untagged
packet refers to the packet without VLAN tag, and the priority-tagged packet refers to the packet
with VLAN tag whose VLAN ID is 0.
Link Types of ports
When creating the 802.1Q VLAN, you should set the link type for the port according to its
connected device. The link types of port including the following two types: Untagged and Tagged.
(1) Untagged: The untagged port can be added in multiple VLANs. If a VLAN-tagged packet
arrives at a port and the VLAN ID in its VLAN tag does not match any of the VLAN the
ingress port belongs to, this packet will be dropped. The packets forwarded by the
untagged port are untagged.
(2) Ta g ge d : The tagged port can be added in multiple VLANs. If a VLAN-tagged packet
arrives at a port and the VLAN ID in its VLAN tag does not match any of the VLAN the
ingress port belongs to, this packet will be dropped. When the VLAN-tagged packets are
forwarded by the Tagged port, its VLAN tag will not be changed.
58
PVID
PVID (Port VLAN ID) is the default VID of the port. When the switch receives an un-VLAN-tagged
packet, it will add a VLAN tag to the packet according to the PVID of its received port and forward
the packets.
When creating VLANs, the PVID of each port, indicating the default VLAN to which the port
belongs, is an important parameter with the following two purposes:
(1) When the switch receives an un-VLAN-tagged packet, it will add a VLAN tag to the packet
according to the PVID of its received port
(2) PVID determines the default broadcast domain of the port, i.e. when the port receives UL
packets or broadcast packets, the port will broadcast the packets in its default VLAN.
Different packets, tagged or untagged, will be processed in different ways, after being received by
ports of different link types, which is illustrated in the following table.
Port Type
Receiving Packets Forwarding Packets
Untagged Packets Tagged Packets Untagged
Packets
Tagged
Packets
Untagged
When untagged
packets are received,
the port will add the
default VL
AN tag, i.e.
the PVID of the
ingress port, to the
packets.
If the VID of packet is
allowed by the port,
the packet will be
received.
If the VID of packet is
forbidden by the port,
the packet will be
dropped.
The packet
will be
forwarded
unchanged.
The packet
will be
forwarded
after
removing its
VLAN tag
Tagged
T
he packet
will be
forwarded
with the
PV ID of
egress port
as
its VLAN
tag.
T
he packet
will be
forwarded
with its
current
VLAN tag.
Table 6-1 Relationship between Port Types and VLAN Packets Processing
IEEE 802.1Q VLAN function is implemented on the VLAN Config pages.
6.1.1 VLAN Config
On this page, you can configure the 802.1Q VLAN and its ports.
59
Choose the menu VLAN→802.1Q VLAN→VLAN Config to load the following page.
Figure 6-3 VLAN Table
To ensure the normal communication of the factory switch, the default VLAN of all ports is set to
VLAN1. VLAN1 cannot be modified or deleted.
The following entries are displayed on this screen:
VLAN Create
VLAN ID
：
Enter the VLAN ID you want to create. It ranges from 2 to 4094.
Name
：
Give a name to the VLAN for identification.
VLAN Ta b l e
VLAN ID Se le ct: Click the Select button to quick-select the corresponding VLAN
based on the VLAN ID you entered.
Select: Select the desired port for configuration.
VLAN ID: Displays the VLAN ID.
Name : Displays the name of the specific VLAN.
Untagged Ports: Show the untagged ports of the specific VLAN.
Tagged Ports: Show the tagged ports of the specific VLAN.
Operation:
You can delete the specific VLAN when you click the word
"Delete".
VLAN M e mber ship
VLAN ID: Displays the VLAN ID you choose.
VLAN Name: Here you can set the name of the VLAN you choose.
60
Port: Displays the port number.
Untagged: The port
will be an untagged member of the specific VLAN if you
select it.
Tagged:
The port will be an tagged member of the specific VLAN if you
select it.
NotMember:
The port will not be a member of the specific VLAN if you select
it.
PVID: Here you can change the PVID of the specific port.
LAG: Displays the LAG to which the port belongs to.
6.2 Application Example for 802.1Q VLAN
Network Requirements
Switch A is connecting to PC A and Server B;
Switch B is connecting to PC B and Server A;
PC A and Server A is in the same VLAN;
PC B and Server B is in the same VLAN;
PCs in the two VLANs cannot communicate with each other.
Network Diagram
61
Configuration Procedure
Configure Switch A
Ste p Operation Description
1
Configure the
Link Type of the
ports
Required. On VLAN→802.1Q VLAN→VL AN Config
page, configure
the link type of Port 2, Port 3 and Port 4 as Untagged, Tagged and
Untagged respectively
2
Create VLAN10 Required. On VLAN→802.1Q VLAN→VLAN Config
page, create a
VLAN with its VLAN ID as 10, owning Port 2 and Port 3.
3
Create VLAN20 Required. On VLAN→802.1Q VLAN→VLAN Config
page, create a
VLAN with its VLAN ID as 20, owning Port 3 and Port 4.
Configure Switch B
Ste p Operation Description
1
Configure the
Link Type of the
ports
Required. On VLAN→802.1Q VLAN→VL AN Config
page, configure
the link type of Port 7, Port 6 and Port 8 as Untagged, Tagged and
Untagged respectively.
2
Create VLAN10 Required. On VLAN→802.1Q VLAN→VLAN Config
page, create a
VLAN with its VLAN ID as 10, owning Port 6 and Port 8.
3
Create VLAN20 Required. On VLAN→802.1Q VLAN→VLAN Config
page, create a
VLAN with its VLAN ID as 20, owning Port 6 and Port 7.
Return to CONTENTS
62
Chapter 7 Spanning Tree
STP (Spanning Tree Protocol), subject to IEEE 802.1D standard, is to disbranch a ring network in
the Data Link layer in a local network. Devices running STP discover loops in the network and block
ports by exchanging information, in that way, a ring network can be disbranched to form a
tree-topological ring-free network to prevent packets from being duplicated and forwarded endlessly
in the network.
BPDU (Bridge Protocol Data Unit) is the protocol data that STP and RSTP use. Enough
information is carried in BPDU to ensure the spanning tree generation. STP is to determine the
topology of the network via transferring BPDUs between devices.
To implement spanning tree function, the switches in the network transfer BPDUs between each
other to exchange information and all the switches supporting STP receive and process the
received BPDUs. BPDUs carry the information that is needed for switches to figure out the
spanning tree.
STP Ele me nts
Bridge ID(Bridge Identifier): Indicates the value of the priority and MAC address of the bridge.
Bridge ID can be configured and the switch with the lower bridge ID has the higher priority.
Root Bridge : Indicates the switch has the lowest bridge ID. Configure the best PC in the ring
network as the root bridge to ensure best network performance and reliability.
De signated Bridge : Indicates the switch has the lowest path cost from the switch to the root
bridge in each network segment. BPDUs are forwarded to the network segment through the
designated bridge. The switch with the lowest bridge ID will be chosen as the designated bridge.
Root Path Cost: Indicates the sum of the path cost of the root port and the path cost of all the
switches that packets pass through. The root path cost of the root bridge is 0.
Bridge Priority: The bridge priority can be set to a value in the range of 0~32768. The lower value
priority has the higher priority. The switch with the higher priority has more chance to be chosen as
the root bridge.
Root Port: Indicates the port that has the lowest path cost from this bridge to the Root Bridge and
forwards packets to the root.
Designated Port: Indicates the port that forwards packets to a downstream network segment or
switch.
Port Priority: The port priority can be set to a value in the range of 0~255. The lower value priority
has the higher priority. The port with the higher priority has more chance to be chosen as the root
port.
Path Cost: Indicates the parameter for choosing the link path by STP. By calculating the path cost,
STP chooses the better links and blocks the redundant links so as to disbranch the ring-network to
form a tree-topological ring-free network.
The following network diagram shows the sketch map of spanning tree. Switch A, B and C are
connected together in order. After STP generation, switch A is chosen as root bridge, the path from
port 2 to port 6 is blocked.
Bridge: Switch A is the root bridge in the whole network; switch B is the designated bridge of
switch C.
Port: Port 3 is the root port of switch B and port 5 is the root port of switch C; port 1 is the
designated port of switch A and port 4 is the designated port of switch B; port 6 is the blocked
port of switch C.
63
Figure 7-1 Basic STP diagram
STP Time rs
Hello Time:
Hello Time ranges from 1 to 10 seconds. It specifies the interval to send BPDU packets. It is used
to test the links.
Max. Age:
Max. Age ranges from 6 to 40 seconds. It specifies the maximum time the switch can wait without
receiving a BPDU before attempting to reconfigure.
Forward Delay:
Forward Delay ranges from 4 to 30 seconds. It specifies the time for the port to transit its state
after the network topology is changed.
When the STP regeneration caused by network malfunction occurs, the STP structure will get
some corresponding change. However, as the new configuration BPDUs cannot be spread in the
whole network at once, the temporal loop will occur if the port transits its state immediately.
Therefore, STP adopts a state transit mechanism, that is, the new root port and the designated
port begins to forward data after twice forward delay, which ensures the new configuration BPDUs
are spread in the whole network.
BPDU Comparing Principle in STP mode
Assuming two BPDUs: BPDU X and BPDU Y
If the root bridge ID of X is smaller than that of Y, X is superior to Y.
If the root bridge ID of X equals that of Y, but the root path cost of X is smaller than that of Y, X is
superior to Y.
If the root bridge ID and the root path cost of X equal those of Y, but the bridge ID of X is smaller
than that of Y, X is superior to Y.
If the root bridge ID, the root path cost and bridge ID of X equal those of Y, but the port ID of X is
smaller than that of Y, X is superior to Y.
STP Ge ne ration
In the beginning
In the beginning, each switch regards itself as the root, and generates a configuration BPDU for
each port on it as a root, with the root path cost being 0, the ID of the designated bridge being that
of the switch, and the designated port being itself.
64
Comparing BPDUs
Each switch sends out configuration BPDUs and receives a configuration BPDU on one of its ports
from another switch. The following table shows the comparing operations.
Ste p Operation
1
If the priority of the BPDU received on the port is lower than that of the BPDU if of
the port itself, the switch discards the BPDU and does not change the BPDU of
the port.
2
If the priority of the BPDU is higher than that of the BPDU of the port itself, the
switch replaces the BPDU of the port with the received one and compares it with
those of other ports on the switch to obtain the one with the highest priority.
Table 7-1 Comparing BPDUs
Selecting the root bridge
The root bridge is selected by BPDU comparing. The switch with the smallest root ID is chosen as
the root bridge.
Selecting the root port and designate port
The operation is taken in the following way:
Ste p Operation
1
For each switch (except the one chosen as the root bridge) in a network, the port
that receives the BPDU with the highest priority is chosen as the root port of the
switch.
2 Using the root port BPDU and the root path co
st, the switch generates a
designated port BPDU for each of its ports.
Root ID is replaced with that of the root port;
Root path is replaced with the sum of the root path cost of the root port and
the path cost between this port and the root port;
The ID of the designated bridge is replaced with that of the switch;
The ID of the designated port is replaced with that of the port.
3
The switch compares the resulting BPDU with the BPDU of the desired port
whose role you want to determine.
If the resulting B
PDU takes the precedence over the BPDU of the port, the
port is chosen as the designated port and the BPDU of this port is replaced
with the resulting BPDU. The port regularly sends out the resulting BPDU;
If the BPDU of this port takes the precedence over
the resulting BPDU, the
BPDU of this port is not replaced and the port is blocked. The port only can
receive BPDUs.
Table 7-2 Selecting root port and designated port
Tips
：
In an STP with stable topology, only the root port and designated port can forward data, and the
other ports are blocked. The blocked ports only can receive BPDUs.
65
RSTP (Rapid Spanning Tree Protocol), evolved from the 802.1D STP standard, enable Ethernet
ports to transit their states rapidly. The premises for the port in the RSTP to transit its state rapidly
are as follows.
The condition for the root port to transit its port state rapidly: The old root port of the switch
stops forwarding data and the designated port of the upstream switch begins to forward
data.
The condition for the designated port to transit its port state rapidly: The designated port is
an edge port or connecting to a point-to-point link. If the designated port is an edge port, it
can directly transit to forwarding state; if the designated port is connecting to a
point-to-point link, it can transit to forwarding state after getting response from the
downstream switch through handshake.
RSTP Elements
Edge Port: Indicates the port connected directly to terminals.
P2P Link: Indicates the link between two switches directly connected.
MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RSTP and subject to IEEE
802.1s standard, not only enables spanning trees to converge rapidly, but also enables packets of
different VLANs to be forwarded along their respective paths so as to provide redundant links
with a better load-balancing mechanism.
Features of MSTP:
MSTP combines VLANs and spanning tree together via VLAN-to-instance mapping table. It
binds several VLANs to an instance to save communication cost and network resources.
MSTP divides a spanning tree network into several regions. Each region has several
internal spanning trees, which are independent of each other.
MSTP provides a load-balancing mechanism for the packets transmission in the VLAN.
MSTP is compatible with both STP and RSTP.
M STP Elements
MST Region (Multiple Spanning Tree Region): An MST Region comprises switches with the same
region configuration and VLAN-to-Instances mapping relationship.
IST (Internal Spanning Tree): An IST is a spanning tree in an MST.
CST (Common Spanning Tree): A CST is the spanning tree in a switched network that connects all
MST regions in the network.
CIST (Common and Internal Spanning Tree): A CIST, comprising IST and CST, is the spanning
tree in a switched network that connects all switches in the network.
66
The following figure shows the network diagram in MSTP.
Figure 7-2 Basic MSTP diagram
M STP
MSTP divides a network into several MST regions. The CST is generated between these MST
regions, and multiple spanning trees can be generated in each MST region. Each spanning tree is
called an instance. As well as STP, MSTP uses BPDUs to generate spanning tree. The only
difference is that the BPDU for MSTP carries the MSTP configuration information on the switches.
Port States
In an MSTP, ports can be in the following four states:
Forwarding: In this status the port can receive/forward data, receive/send BPDU packets as
well as learn MAC address.
Learning: In this status the port can receive/send BPDU packets and learn MAC address.
Blocking: In this status the port can only receive BPDU packets.
Disconnected: In this status the port is not participating in the STP.
Port Roles
In an MSTP, the following roles exist:
Root Port: Indicates the port that has the lowest path cost from this bridge to the Root Bridge
and forwards packets to the root.
Designated Port: Indicates the port that forwards packets to a downstream network segment
or switch.
Master Port: Indicates the port that connects an MST region to the common root. The path
from the master port to the common root is the shortest path between this MST region and
the common root.
Alternate Port: Indicates the port that can be a backup port of a root or master port.
Backup Port: Indicates the port that is the backup port of a designated port.
Disabled: Indicates the port that is not participating in the S T P.
67
The following diagram shows the different port roles.
Figure 7-3 Port roles
The Spanning Tree module is mainly for spanning tree configuration of the switch, including four
submenus: STP Config, Port Config, M STP Instance and STP Security.
7.1 STP Config
The STP Config function, for global configuration of spanning trees on the switch, can be
implemented on STP Config and STP Summary pages.
7.1.1 STP Config
Before configuring spanning trees, you should make clear the roles each switch plays in each
spanning tree instance. Only one switch can be the root bridge in each spanning tree instance. On
this page you can globally configure the spanning tree function and related parameters.
Choose the menu Spanning Tree→STP Config→STP Config to load the following page.
Figure 7-4 STP Config
68
The following entries are displayed on this screen:
Global Config
STP: Select Enable/Disable STP function globally on the switch.
Ve r s i o n : Select the desired STP version on the switch.
STP: Spanning Tree Protocol.
RSTP: Rapid Spanning Tree Protocol.
MSTP: Multiple Spanning Tree Protocol.
Parameters Config
CIST Priority:
Enter a value from 0 to 61440 to specify the priority of the switch
fo
r comparison in the CIST. CIST priority is an important criterion
on determining the root bridge. In the same condition, the switch
with the highest priority will be chosen as the root bridge. The
lower value has the higher priority. The default value is 32768 and
should be exact divisor of 4096.
Hello Time
Enter a value from 1 to 10 in seconds to specify the interval to
send BPDU packets. It is used to test the links. 2*(Hello Time + 1)
≤ Max Age. The default value is 2 seconds.
Max Age: Enter a value f
rom 6 to 40 in seconds to specify the maximum
time the switch can wait without receiving a BPDU before
attempting to reconfigure. The default value is 20 seconds.
Forward Delay:
Enter a value from 4 to 30 in seconds to specify the time for the
port to tra
nsit its state after the network topology is changed.
2*(Forward Delay-1) ≥ Max Age. The default value is 15 seconds.
TxHold Count:
Enter a value from 1 to 20 to set the maximum number of BPDU
packets transmitted per Hello Time interval. The default value is
5pps.
Max Hops: Enter a value from 1 to 40 to set the maximum number of hops
that occur in a specific region before the BPDU is discarded. The
default value is 20 hops.
Note:
1. The forward delay parameter and the network diameter are correlated. A too small forward
delay parameter may result in temporary loops. A too large forward delay may cause a
network unable to resume the normal state in time. The default value is recommended.
2. An adequate hello time parameter can enable the switch to discover the link failures occurred
in the network without occupying too much network resources. A too large hello time
parameter may result in normal links being regarded as invalid when packets drop occurred in
the links, which in turn result in spanning tree being regenerated. A too small hello time
parameter may result in duplicated configuration being sent frequently, which increases the
network load of the switches and wastes network resources. The default value is
recommended.
3. A too small max age parameter may result in the switches regenerating spanning trees
frequently and cause network congestions to be falsely regarded as link problems. A too large
max age parameter result in the switches unable to find the link problems in time, which in
turn handicaps spanning trees being regenerated in time and makes the network less
adaptive. The default value is recommended.
4. If the TxHold Count parameter is too large, the number of MSTP packets being sent in each
hello time may be increased with occupying too much network resources. The default value is
recommended.
69
7.1.2 STP Summary
On this page you can view the related parameters for Spanning Tree function.
Choose the menu Spanning Tree→STP Config→STP Summary to load the following page.
Figure 7-5 STP Summary
7.2 Port Config
On this page you can configure the parameters of the ports for CIST.
70
Choose the menu Spanning Tree→Port Config to load the following page.
Figure 7-6 Port Config
The following entries are displayed on this screen:
Port Config
Port Sele ct: Click the Select button to quick-
select the corresponding port based
on the port number you entered.
Select: Select the desired port for STP configuration. It is multi-optional.
Port: Displays the port number of the switch.
Status: Select Enable /Disable STP function for the desired port.
Priority:
Enter a value from 0 to 240 divisible by 16. Port priority is an
important criterion on determining if the port connected to this port
will be chosen as the root port. The lower value has the higher
priority.
ExtPath:
ExtPath Cost is used to choose the path and calculate the path costs
of ports in different MST regions. It is an important criterion on
determining the root port. The lower value has the higher priority.
IntPath: IntPath Cost is used to choose the p
ath and calculate the path costs
of ports in an MST region. It is an important criterion on determining
the root port. The lower value has the higher priority.
Edge Port:
Select Enable/Disable Edge Port. The edge port can transit its state
from blocking to forwarding rapidly without waiting for forward delay.
P2P Link:
Select the P2P link status. If the two ports in the P2P link are root port
or designated port, they can transit their states to forwarding rapidly
to reduce the unnecessary forward delay.
MCheck:
Select Enable to perform MCheck operation on the port. Unchange
means no MCheck operation.
STP Ve rsion: Displays the STP version of the port.
71
Port Role: Displays the role of the port played in the STP Instance.
Root Port: Indicates the port that
has the lowest path cost from
this bridge to the Root Bridge and forwards packets to the root.
Designated Port: Indicates the port that forwards packets to a
downstream network segment or switch.
Master Port: Indicates the port that connects an MST region to
the common root. The path from the master port to the common
root is the shortest path between this MST region and the
common root.
Alternate Port: Indicates the port that can be a backup port of a
root or master port.
Backup Port: Indicates the port t
hat is the backup port of a
designated port.
Disabled: Indicates the port that is not participating in the STP.
Port Status: Displays the working status of the port.
Forwarding: In this status the port can receive/forward data,
receive/send BPDU packets as well as learn MAC address.
Learning: In this status the port can receive/send BPDU packets
and learn MAC address.
Blocking: In this status the port can only receive BPDU packets.
Disconnected: In this status the port is not participating in the
S T P.
LAG: Displays the LAG number which the port belongs to.
Note:
1. Configure the ports connected directly to terminals as edge ports and enable the BPDU
protection function as well. This not only enables these ports to transit to forwarding state
rapidly but also secures your network.
2. All the links of ports in a LAG can be configured as point-to-point links.
3. When the link of a port is configured as a point-to-point link, the spanning tree instances
owning this port are configured as point-to-point links. If the physical link of a port is not a
point-to-point link and you forcibly configure the link as a point-to-point link, temporary loops
may be incurred.
7.3 MSTP Instance
MSTP combines VLANs and spanning tree together via VLAN-to-instance mapping table
(VLAN-to-spanning-tree mapping). By adding MSTP instances, it binds several VLANs to an
instance to realize the load balance based on instances.
Only when the switches have the same MST region name, MST region revision and
VLAN-to-Instance mapping table, the switches can be regarded as in the same MST region.
The MSTP Instance function can be implemented on Region Config, Instance Config and
Instance Port Config pages.
7.3.1 Region Config
On this page you can configure the name and revision of the MST region
72
Choose the menu Spanning Tree→MSTP Instance→Region Config to load the following page.
Figure 7-7 Region Config
The following entries are displayed on this screen:
Region Config
Region Name: Create a name for MST region identification using up to 32 characters.
Revision: Enter the revision from 0 to 65535 for MST region identification.
7.3.2 Instance Config
Instance Configuration, a property of MST region, is used to describe the VLAN to Instance
mapping configuration. You can assign VLAN to different instances appropriate to your needs.
Every instance is a VLAN group independent of other instances and CIST.
Choose the menu Spanning Tree→M STP Instance →Instance Config to load the following page.
Figure 7-8 Instance Config
73
The following entries are displayed on this screen:
Instance Table
Instance ID Select: Click the Select button to quick-selec
t the corresponding Instance ID
based on the ID number you entered.
Select: Select the desired Instance ID for configuration. It is multi-optional.
Instance: Displays Instance ID of the switch.
Status: Displays the status of the instance.
Priority: Ent
er the priority of the switch in the instance. It is an important
criterion on determining if the switch will be chosen as the root bridge
in the specific instance.
VLAN ID:
Enter the VLAN ID which belongs to the corresponding instance ID.
After modificat
ion here, the previous VLAN ID will be cleared and
mapped to the CIST.
Clear: Click the Cle ar
button to clear up all VLAN IDs from the instance ID.
The cleared VLAN ID will be automatically mapped to the CIST.
VLAN-Instance Mapping
VLAN ID: Enter the de
sired VLAN ID. After modification here, the new VLAN ID
will be added to the corresponding instance ID and the previous
VLAN ID won’t be replaced.
Instance ID: Enter the corresponding instance ID.
7.3.3 Instance Port Config
A port can play different roles in different spanning tree instance. On this page you can configure
the parameters of the ports in different instance IDs as well as view status of the ports in the
specified instance.
74
Choose the menu Spanning Tree→M STP Instance →Instance Port Config to load the following
page.
Figure 7-9 Instance Port Config
The following entries are displayed on this screen:
Port Config
Instance ID: Select the desired instance ID for its port configuration.
Port Sele ct: Click the Select button to quick-
select the corresponding port based
on the port number you entered.
Select:
Select the desired port to specify its priority and path cost. It is
multi-optional.
Port: Displays the port number of the switch.
Priority: Enter the prio
rity of the port in the instance. It is an important criterion
on determining if the port connected to this port will be chosen as the
root port.
Path Cost:
Path Cost is used to choose the path and calculate the path costs of
ports in an MST region. It is
an important criterion on determining the
root port. The lower value has the higher priority.
Port Role: Displays the role of the port played in the MSTP Instance.
Port Status: Displays the working status of the port.
LAG: Displays the LAG number which the port belongs to.
Note:
The port status of one port in different spanning tree instances can be different.
75
Global configuration Procedure for Spanning Tree function:
Step Operation Description
1
Make clear roles the switches
play in spanning tree
in
stances: root bridge or
designated bridge
Preparation.
2
Globally configure MSTP
parameters
Required.
Enable Spanning Tree function on the switch
and configure MSTP parameters on Spanning
Tr e e →STP Config→STP Config page.
3
Configure MSTP parameters
for ports
Required.
Configure MSTP parameters for ports on
Spanning Tree→Port Config→Port Config page.
4 Configure the MST region
Required. Create MST region and configure the role the
switch plays in the MST region on Spanning
Tr e e →M STP Instance →Region Config and Instance
Config page.
5
Configure MSTP parameters
for instance ports
Optional. Configure different instances in the MST region
and configure MSTP parameters for instance ports on
Spanning Tree→M STP Instance→Instance Port
Config page.
7.4 STP Security
Configuring protection function for devices can prevent devices from any malicious attack against
STP features. The STP Security function can be implemented on Port Protect and TC Protect
pages.
Port Protect function is to prevent the devices from any malicious attack against STP features.
7.4.1 Port Protect
On this page you can configure loop protect feature, root protect feature, TC protect feature,
BPDU protect feature and BPDU filter feature for ports. You are suggested to enable
corresponding protection feature for the qualified ports.
Loop Protect
In a stable network, a switch maintains the states of ports by receiving and processing BPDU
packets from the upstream switch. However, when link congestions or link failures occurred to the
network, a down stream switch does not receive BPDU packets for certain period, which results in
spanning trees being regenerated and roles of ports being reselected, and causes the blocked
ports to transit to forwarding state. Therefore, loops may be incurred in the network.
The loop protect function can suppresses loops. With this function enabled, a port, regardless of
the role it plays in instances, is always set to blocking state, when the port does not receive BPDU
packets from the upstream switch and spanning trees are regenerated, and thereby loops can be
prevented.
Root Protect
A CIST and its secondary root bridges are usually located in the high-bandwidth core region.
Wrong configuration or malicious attacks may result in configuration BPDU packets with higher
priorities being received by the legal root bridge, which causes the current legal root bridge to lose
76
its position and network topology jitter to occur. In this case, flows that should travel along
high-speed links may lead to low-speed links, and network congestion may occur.
To avoid this, MSTP provides root protect function. Ports with this function enabled can only be set
as designated ports in all spanning tree instances. When a port of this type receives BDPU
packets with higher priority, it transits its state to blocking state and stops forwarding packets (as if
it is disconnected from the link). The port resumes the normal state if it does not receive any
configuration BPDU packets with higher priorities for a period of two times of forward delay.
TC Prote ct
A switch removes MAC address entries upon receiving TC-BPDU packets. If a user maliciously
sends a large amount of TC-BPDU packets to a switch in a short period, the switch will be busy
with removing MAC address entries, which may decrease the performance and stability of the
network.
To prevent the switch from frequently removing MAC address entries, you can enable the TC
protect function on the switch. With TC protect function enabled, if the account number of the
received TC-BPDUs exceeds the maximum number you set in the TC threshold field, the switch
will not performs the removing operation in the TC protect cycle. Such a mechanism prevents the
switch from frequently removing MAC address entries.
BPDU Protect
Ports of the switch directly connected to PCs or servers are configured as edge ports to rapidly
transit their states. When these ports receive BPDUs, the system automatically configures these
ports as non-edge ports and regenerates spanning trees, which may cause network topology jitter.
Normally these ports do not receive BPDUs, but if a user maliciously attacks the switch by sending
BPDUs, network topology jitter occurs.
To prevent this attack, MSTP provides BPDU protect function. With this function enabled on the
switch, the switch shuts down the edge ports that receive BPDUs and reports these cases to the
administrator. If a port is shut down, only the administrator can restore it.
BPDU Filter
BPDU filter function is to prevent BPDUs flood in the STP network. If a switch receives malicious
BPDUs, it forwards these BPDUs to the other switched in the network, which may result in
spanning trees being continuously regenerated. In this case, the switch occupying too much CPU
or the protocol status of BPDUs is wrong.
With BPDU filter function enabled, a port does not receive or forward BPDUs, but it sends out its
own BPDUs. Such a mechanism prevents the switch from being attacked by BPDUs so as to
guarantee generation the spanning trees correct.
77
Choose the menu Spanning Tree→STP Se curity→Port Protect to load the following page.
Figure 7-10 Port Protect
The following entries are displayed on this screen:
Port Prote ct
Port Sele ct: Click the Select button to quick-
select the corresponding port based
on the port number you entered.
Select:
Select the desired port for port protect configuration. It is
multi-optional.
Port: Displays the port number of the switch.
Loop Protect:
Loop Protect is to prevent the loops in the network brought by
recalculating STP because of link failures and network congestions.
Root Protect:
Root Protect is to prevent wrong network topology change caused by
the role change of the current legal root bridge.
TC Protect:
TC Protect is to prevent the decrease of the performance and
stability
of the switch brought by continuously removing MAC
address entries upon receiving TC-BPDUs in the STP network.
BPDU Protect:
BPDU Protect is to prevent the edge port from being attacked by
maliciously created BPDUs
BPDU Filter: BPDU Filter is to prevent BPDUs flood in the STP network.
LAG: Displays the LAG number which the port belongs to.
78
7.4.2 TC Protect
When TC Protect is enabled for the port on Port Protect page, the TC threshold and TC protect
cycle need to be configured on this page.
Choose the menu Spanning Tree→STP Security→TC Prote ct to load the following page.
Figure 7-11 TC Protect
The following entries are displayed on this screen:
TC Prote ct
TC Thre shold: Enter a number from 1 to 100. It is the maximu
m number of the
TC-
BPDUs received by the switch in a TC Protect Cycle. The
default value is 20.
TC Protect Cycle:
Enter a value from 1 to 10 to specify the TC Protect Cycle. The
default value is 5.
7.5 Application Example for STP Function
Network Requirements
Switch A, B, C, D and E all support MSTP function.
A is the central switch.
B and C are switches in the convergence layer. D, E and F are switches in the access layer.
There are 6 VLANs labeled as VLAN101-VLAN106 in the network.
All switches run MSTP and belong to the same MST region.
The data in VLAN101, 103 and 105 are transmitted in the STP with B as the root bridge. The
data in VLAN102, 104 and 106 are transmitted in the STP with C as the root bridge.
Network Diagram
79
Configuration Procedure
Configure Switch A:
Step Operation Description
1 Configure ports On VL AN→802.1Q VLAN
page, configure the link
type of the related ports as Tagged
, and add the ports
to VLAN101-VLAN
106. The detailed instructions can
be found in the section 802.1Q VLAN.
2 Enable STP function On Spanning Tree→STP Config→STP Config page,
enable STP function and select MSTP version.
On Spanning Tree→STP Config→Port Config page,
enable MSTP function for the port.
3
Configure the region name and
the revision of MST region
On Spanning Tree→M STP Instance→Re gion
Config page, configure the region as TP-
LINK and
keep the default revision setting.
4 Configure VLAN-to-Instance
mapping table of the MST region
On Spanning Tree→M STP Instance →Instance
Config page, configure VLAN-to-
Instance mapping
table. Map VLAN 101, 103 and
105 to Instance 1; map
VLAN 102, 104 and 106 to Instance 2.
Configure Switch B:
Step Operation Description
1 Configure ports On VL AN→802.1Q VLAN
page, configure the link
type of the related ports as Tagged
, and add the ports
to VLAN101-VLAN106. The det
ailed instructions can
be found in the section 802.1Q VLAN.
2 Enable STP function On Spanning Tree→STP Config→STP Config page,
enable STP function and select MSTP version.
On Spanning Tree→STP Config→Port Config page,
enable MSTP function for the port.
3
Configure the region name and
the revision of MST region
On Spanning Tree→M STP Instance→Re gion
Config page, configure the region as TP-
LINK and
keep the default revision setting.
4 Configure VLAN-to-Instance
mapping table of the MST region
On Spanning Tree→M STP Instance →Instance
Config page, configure VLAN-to-
Instance mapping
table. Map VLAN 101, 103 and 105 to Instance 1; map
VLAN 102, 104 and 106 to Instance 2.
5
Configure switch B as the root
bridge of Instance 1
On Spanning Tree→M STP Instance →Instance
Config
page, configure the priority of Instance 1 to be
0.
6
Configure switch B as the
designated bridge of Instance 2
On Spanning Tree→M STP Instance →Instance
Config
page, configure the priority of Instance 2 to be
4096.
80
Configure Switch C:
Step Operation Description
1 Configure ports On VLAN→802.1Q VLAN
page, configure the link
type of the related ports as Tagged
, and add the ports
to VLAN101-VLAN
106. The detailed instructions can
be found in the section 802.1Q VLAN.
2 Enable STP function On Spanning Tree→STP Config→STP Config
page, enable STP function and select MSTP version.
On Spanning Tree →STP Config→Port Config
page, enable MSTP function for the port.
3 Configure the region name and
the revision of MST region
On Spanning Tree→MSTP Instance→Region
Config page, configure the region as TP-
LINK and
keep the default revision setting.
4 Configure VLAN-to-Instance
mapping table of the MST region
On Spanning Tree→M STP Instance→Instance
Config page, configure VLAN-to-I
nstance mapping
table. Map VLAN101, 103
and 105 to Instance 1; map
VLAN102, 104 and 106 to Instance 2.
5
Configure switch C as the root
bridge of Instance 1
On Spanning Tree→M STP Instance→Instance
Config page, configure t
he priority of Instance 1 to be
4096.
6
Configure switch C as the root
bridge of Instance 2
On Spanning Tree→M STP Instance→Instance
Config
page, configure the priority of Instance 2 to be
0.
Configure Switch D:
Step Operation Description
1 Configure ports On VLAN→802.1Q VLAN
page, configure the link
type of the related ports as Tagged
, and add the ports
to VLAN101-VLAN
106. The detailed instructions can
be found in the section 802.1Q VLAN.
2 Enable STP function On Spanning Tree→STP Config→STP Config
page, enable STP function and select MSTP version.
On Spanning Tree →STP Config→Port Config
page, enable MSTP function for the port.
3
Configure the region name and
the revision of MST region
On Spanning Tree→M STP Instance→Re gion
Config page, configure the region as TP-
LINK and
keep the default revision setting.
4 Configure VLAN-to-Instance
mapping table of the MST region
On Spanning Tree→M STP Instance→Instance
Config page, configure VLAN-to-Instance mapping
table. Map VLAN101, 103
and 105 to Instance 1; map
VLAN102, 104 and 106 to Instance 2.
81
The configuration procedure for switch E and F is the same with that for switch D.
The topology diagram of the two instances after the topology is stable
For Instance 1 (VLAN101, 103 and 105), the red paths in the following figure are connected
links; the gray paths are the blocked links.
For Instance 2 (VLAN102, 104 and 106), the blue paths in the following figure are connected
links; the gray paths are the blocked links.
Suggestion for Configuration
Enable TC Protect function for all the ports of switches.
Enable Root Protect function for all the ports of root bridges.
Enable Loop Protect function for the non-edge ports.
Enable BPDU Protect function or BPDU Filter function for the edge ports which are connected to
the PC and server.
Return to CONTENTS
82
Chapter 8 Multicast
Multicast Overview
In the network, packets are sent in three modes: unicast, broadcast and multicast. In unicast, the
source server sends separate copy information to each receiver. When a large number of users
require this information, the server must send many pieces of information with the same content to
the users. Therefore, large bandwidth will be occupied. In broadcast, the system transmits
information to all users in a network. Any user in the network can receive the information, no
matter the information is needed or not.
Point-to-multipoint multimedia business, such as video conferences and VoD (video-on-demand),
plays an important part in the information transmission field. Suppose a point to multi-point service
is required, unicast is suitable for networks with sparsely users, whereas broadcast is suitable for
networks with densely distributed users. When the number of users requiring this information is
not certain, unicast and broadcast deliver a low efficiency. Multicast solves this problem. It can
deliver a high efficiency to send data in the point to multi-point service, which can save large
bandwidth and reduce the network load. In multicast, the packets are transmitted in the following
way as shown in Figure 8-1.
Figure 8-1 Information transmission in the multicast mode
Features of multicast:
1. The number of receivers is not certain. Usually point-to-multipoint transmission is needed;
2. Multiple users receiving the same information form a multicast group. The multicast information
sender just need to send the information to the network device once;
3. Each user can join and leave the multicast group at any time;
4. Real time is highly demanded and certain packets drop is allowed.
83
Multicast Address
1. Multicast IP Address:
As specified by IANA (Internet Assigned Numbers Authority), Class D IP addresses are used as
destination addresses of multicast packets. The multicast IP addresses range from
224.0.0.0~239.255.255.255. The following table displays the range and description of several
special multicast IP addresses.
Multicast IP address range Description
224.0.0.0～224.0.0.255
Reserved multicast addresses for routing protocols
and other network protocols
224.0.1.0～224.0.1.255 Addresses for video conferencing
239.0.0.0～239.255.255.255
Local management multicast addresses, which are
used in the local network only
Table 8-1 Range of the special multicast IP
2. Multicast MAC Address:
When a unicast packet is transmitted in an Ethernet network, the destination MAC address is the
MAC address of the receiver. When a multicast packet is transmitted in an Ethernet network, the
destination is not a receiver but a group with uncertain number of members, so a multicast MAC
address, a logical MAC address, is needed to be used as the destination address.
As stipulated by IANA, the high-order 24 bits of a multicast MAC address begins with 01-00-5E
while the low-order 23 bits of a multicast MAC address are the low-order 23 bits of the multicast IP
address. The mapping relationship is described as Figure 8-2.
Figure 8-2 Mapping relationship between multicast IP address and multicast MAC address
The high-order 4 bits of the IP multicast address are 1110, identifying the multicast group. Only 23
bits of the remaining low-order 28 bits are mapped to a multicast MAC address. In that way, 5 bits
of the IP multicast address is not utilized. As a result, 32 IP multicast addresses are mapped to the
same MAC addresses.
Multicast Address Table
The switch is forwarding multicast packets based on the multicast address table. As the
transmission of multicast packets cannot span the VLAN, the first part of the multicast address
table is VLAN ID, based on which the received multicast packets are forwarded in the VLAN
owning the receiving port. The multicast address table is not mapped to an egress port but a group
port list. When forwarding a multicast packet, the switch looks up the multicast address table
based on the destination multicast address of the multicast packet. If the corresponding entry
cannot be found in the table, the switch will broadcast the packet in the VLAN owning the receiving
port. If the corresponding entry can be found in the table, it indicates that the destination address
84
should be a group port list, so the switch will duplicate this multicast data and deliver each port one
copy. The general format of the multicast address table is described as Figure 8-3 below.
VLAN ID
Multicast IP
Port
Figure 8-3 Multicast Address Table
IGMP Snooping
In the network, the hosts apply to the near router for joining (leaving) a multicast group by sending
IGMP (Internet Group Management Protocol) messages. When the up-stream device forwards
down the multicast data, the switch is responsible for sending them to the hosts. IGMP Snooping is
a multicast control mechanism, which can be used on the switch for dynamic registration of the
multicast group. The switch, running IGMP Snooping, manages and controls the multicast group via
listening to and processing the IGMP messages transmitted between the hosts and the multicast
router, thereby effectively prevents multicast groups being broadcasted in the network.
The Multicast module is mainly for multicast management configuration of the switch, including
four submenus: IGMP Snooping, Multicast IP, Multicast Filter and Packet Statistics.
8.1 IGMP Snooping
IGMP Snooping Process
The switch, running IGMP Snooping, listens to the IGMP messages transmitted between the host
and the router, and tracks the IGMP messages and the registered port. When receiving IGMP
report message, the switch adds the port to the multicast address table; when the switch listens to
IGMP leave message from the host, the router sends the Group-Specific Query message of the
port to check if other hosts need this multicast, if yes, the router will receive IGMP report message;
if no, the router will receive no response from the hosts and the switch will remove the port from
the multicast address table. The router regularly sends IGMP query messages. After receiving the
IGMP query messages, the switch will remove the port from the multicast address table if the
switch receives no IGMP report message from the host within a period of time.
IGMP Messages
The switch, running IGMP Snooping, processes the IGMP messages of different types as follows.
1. IGMP Query Message
IGMP query message, sent by the router, falls into two types, IGMP general query message and
IGMP group-specific-query message. The router regularly sends IGMP general message to query
if the multicast groups contain any member. When receiving IGMP leave message, the receiving
port of the router will send IGMP group-specific-query message to the multicast group and the
switch will forward IGMP group-specific-query message to check if other members in the multicast
group of the port need this multicast.
When receiving IGMP general query message, the switch will forward them to all other ports in the
VLAN owning the receiving port. The receiving port will be processed: if the receiving port is not a
router port yet, it will be added to the router port list with its router port time specified; if the
receiving port is already a router port, its router port time will be directly reset.
When receiving IGMP group-specific-query message, the switch will send the group-specific query
message to the members of the multicast group being queried.
2. IGMP Report Message
IGMP report message is sent by the host when it applies for joining a multicast group or responses
to the IGMP query message from the router.
85
When receiving IGMP report message, the switch will send the report message via the router port
in the VLAN as well as analyze the message to get the address of the multicast group the host
applies for joining. The receiving port will be processed: if the receiving port is a new member port,
it will be added to the multicast address table with its member port time specified; if the receiving
port is already a member port, its member port time will be directly reset.
3. IGMP Leave Message
The host, running IGMPv1, does not send IGMP leave message when leaving a multicast group,
as a result, the switch cannot get the leave information of the host momentarily. However, after
leaving the multicast group, the host does not send IGMP report message any more, so the switch
will remove the port from the corresponding multicast address table when its member port time
times out. The host, running IGMPv2 or IGMPv3, sends IGMP leave message when leaving a
multicast group to inform the multicast router of its leaving.
When receiving IGMP leave message, the switch will forward IGMP group-specific-query message
to check if other members in the multicast group of the port need this multicast and reset the
member port time to the leave time. When the leave time times out, the switch will remove the port
from the corresponding multicast group. If no other member is in the group after the port is
removed, the switch will send IGMP leave message to the router and remove the whole multicast
group.
IGMP Snooping Fundamentals
1. Ports
Router Port: Indicates the switch port directly connected to the multicast router.
Member Port: Indicates a switch port connected to a multicast group member.
2. Timers
Router Port Time : Within the time, if the switch does not receive IGMP query message from the
router port, it will consider this port is not a router port any more. The default value is 300 seconds.
Member Port Time: Within the time, if the switch does not receive IGMP report message from the
member port, it will consider this port is not a member port any more. The default value is 260
seconds.
Le ave Time: Indicates the interval between the switch receiving a leave message from a host and
the switch removing the host from the multicast groups. The default value is 1 second.
The IGMP Snooping function can be implemented on Snooping Config, Port Config, VLAN
Config and Multicast VLAN pages.
8.1.1 Snooping Config
To configure the IGMP Snooping on the switch, please firstly configure IGMP global configuration
and related parameters on this page.
If the multicast address of the received multicast data is not in the multicast address table, the
switch will broadcast the data in the VLAN. When Unknown Multicast Discard feature is enabled,
the switch drops the received unknown multicast so as to save the bandwidth and enhance the
process efficiency of the system. Please configure this feature appropriate to your needs.
86
Choose the menu Multicast→IGMP Snooping→Snooping Config to load the following page.
Figure 8-4 Basic Config
The following entries are displayed on this screen:
Global Config
IGMP Snooping:
Select Enable/Disable IGMP Snooping function globally on the
switch.
Unknown Multicast: Select the operation for the
switch to process unknown multicast,
Forward or Discard.
IGMP Snooping Status
Description: Displays IGMP Snooping status.
M e mber: Displays the member of the corresponding status.
8.1.2 Port Config
On this page you can configure the IGMP feature for ports of the switch.
87
Choose the menu Multicast→IGMP Snooping→Port Config to load the following page.
Figure 8-5 Port Config
The following entries are displayed on this screen:
Port Config
Port Sele ct: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Select:
Select the desired port for IGMP Snooping feature configuration.
It is multi-optional.
Port: Displays the port of the switch.
IGMP Snooping: Select Enable/Disable IGMP Snooping for the desired port.
Fast Leave:
Select Enable/Disable Fast Leave feature for the desired port. If
Fast Leave is enabled for a port, the switch
will immediately
remove this port from the multicast group upon receiving IGMP
leave messages.
LAG: Displays the LAG number which the port belongs to.
Note:
1. Fast Leave on the port is effective only when the host supports IGMPv2 or IGMPv3.
2. When both Fast Leave feature and Unknown Multicast Discard feature are enabled, the
leaving of a user connected to a port owning multi-user will result in the other users
intermitting the multicast business.
8.1.3 VLAN Config
Multicast groups established by IGMP Snooping are based on VLANs. On this page you can
configure different IGMP parameters for different VLANs.
88
Choose the menu Multicast→IGMP Snooping→VLAN Config to load the following page.
Figure 8-6 VLAN Config
The following entries are displayed on this screen:
VLAN Config
VLAN ID: Enter the VLAN ID to enable
IGMP Snooping for the desired
VLAN.
Router Port Time:
Specify the aging time of the router port. Within this time, if the
switch doesn’
t receive IGMP query message from the router port,
it will consider this port is not a router port any more.
M e mber Port Time :
Specify the aging time of the member port. Within this time, if the
switch doesn’
t receive IGMP report message from the member
port, it will consider this port is not a member port any more.
Leave Time: Specify the interval between the switch rec
eiving a leave
message from a host and the switch removing the host from the
multicast groups.
Static Router Port:
Select the static router port which is mainly used in the network
with stable topology.
VLAN Ta b l e
VLAN ID Se le ct: Click the Select button to quick-
select the corresponding VLAN
ID based on the ID number you entered.
Select: Select the desired VLAN ID for configuration. It is multi-optional.
VLAN ID: Displays the VLAN ID.
Router Port Time: Displays the router port time of the VLAN.
M e mber Port Time: Displays the member port time of the VLAN.
89
Leave Time: Displays the leave time of the VLAN.
Router Port: Displays the router port of the VLAN.
Note:
The settings here will be invalid when multicast VLAN is enabled
Configuration procedure:
Step Operation Description
1
Enable IGMP Snooping
function
Required. Enable IGMP Snooping globally on the switch
and for the port on Multicast→I GM P
Snooping→Snooping Config and Port Config page.
2
Configure the multicast
parameters for VLANs
Optional. Configure the multicast parameters for VLANs
on Multicast→IGMP Snooping→VLAN Config page.
If a VLAN has no multicast parameters configuration, it
indicates the IGMP Snooping is not enabled in the VLAN,
thus the multicast data in the VLAN will be broadcasted.
8.1.4 Multicast VLAN
In old multicast transmission mode, when users in different VLANs apply for join the same
multicast group, the multicast router will duplicate this multicast information and deliver each
VLAN owning a receiver one copy. This mode wastes a lot of bandwidth.
The problem above can be solved by configuring a multicast VLAN. By adding switch ports to the
multicast VLAN and enabling IGMP Snooping, you can make users in different VLANs share the
same multicast VLAN. This saves the bandwidth since multicast streams are transmitted only
within the multicast VLAN and also guarantees security because the multicast VLAN is isolated
from user VLANS.
Before configuring a multicast VLAN, you should firstly configure a VLAN as multicast VLAN and
add the corresponding ports to the VLAN on the 802.1Q VLAN page. If the multicast VLAN is
enabled, the multicast configuration for other VLANs on the VLAN Config page will be invalid, that
is, the multicast streams will be transmitted only within the multicast VLAN.
Choose the menu Multicast→IGMP Snooping→Multicast VLAN to load the following page.
Figure 8-7 Multicast VLAN
90
The following entries are displayed on this screen:
Multicast VLAN
Multicast VLAN: Select Enable/Disable Multicast VLAN feature.
VLAN ID: Enter the VLAN ID of the multicast VLAN.
Router Port Time: Specify the aging time of the router po
rt. Within this time, if the
switch doesn’
t receive IGMP query message from the router port,
it will consider this port is not a router port any more.
M e mber Port Time :
Specify the aging time of the member port. Within this time, if the
switch doesn’t rec
eive IGMP report message from the member
port, it will consider this port is not a member port any more.
Leave Time:
Specify the interval between the switch receiving a leave
message from a host, and the switch removing the host from the
multicast groups.
Router Port:
Select the static router port which is mainly used in the network
with stable topology.
Note:
1. The router port should be in the multicast VLAN, otherwise the member ports cannot receive
multicast streams.
2. The Multicast VLAN won't take effect unless you first complete the configuration for the
corresponding VLAN owning the port on the 802.1Q VLAN page.
3. Configure the link type of the router port in the multicast VLAN as Tagged otherwise all the
member ports in the multicast VLAN cannot receive multicast streams.
4. After a multicast VLAN is created, all the IGMP packets will be processed only within the
multicast VLAN.
Configuration procedure:
Step Operation Description
1
Enable IGMP Snooping
function
Required. Enable IGMP Snooping globally on t
he switch
and for the port on Multicast→I GM P
Snooping→Snooping Config and Port Config page.
2 Create a multicast VLAN
Required. Create a multicast VLAN and add all the member
ports and router ports to the VLAN on the V L AN→802.1Q
VLAN page.
Configure the link type of the router ports as Tagged.
3
Configure parameters for
multicast VLAN
Optional. Enable and configure a multicast VLAN on the
Multicast→IGMP Snooping→Multicast VLAN page.
It is recommended to keep the default time parameters.
4 Look over the configuration
If it is successfully configured, the VLAN ID of the multicast
VLAN will be displayed in the IGMP Snooping Status table
on the Multicast→IGMP Snooping→Snooping Config
page.
91
Application Example for Multicast VLAN:
Network Requirements
Multicast source sends multicast streams via the router, and the streams are transmitted to user A
and user B through the switch.
Router: Its WAN port is connected to the multicast source; its LAN port is connected to the switch.
The multicast packets are transmitted in VLAN3.
Switch: Port 3 is connected to the router and the packets are transmitted in VLAN3; port 4 is
connected to user A and the packets are transmitted in VLAN4; port 5 is connected to user B and
the packets are transmitted in VLAN5.
User A: Connected to Port 4 of the switch.
User B: Connected to port 5 of the switch.
Configure a multicast VLAN, and user A and B receive multicast streams through the multicast
VLAN.
Network Diagram
Configuration Procedure
Step Operation Description
1 Create VLANs
Create three VLANs with the VLAN ID 3, 4 and 5 respectively,
and specify the description of VLAN3 as Multicast VLAN on
VLAN→802.1Q VLAN page.
2 Configure ports On VLAN→802.1Q VLAN function pages.
For port 3, configure its link type as Tagged
, and add it to VLAN3,
VLAN4 and VLAN5.
For port 4, configure its link type as Untagged
, and add it to
VLAN3 and VLAN 4.
For port 5, configure its link type as Untagged
, and add it to
VLAN3 and VLAN 5.
92
Step Operation Description
3
Enable IGMP
Snooping function
Enable IGMP Snooping function globally on Multicast→IGM P
Snooping→Snooping Config
page. Enable IGMP Snooping
function for port 3, port 4 and port 5 on M ulticast→IGM P
Snooping→Port Config page.
4
Enable Multicast
VLAN
Enable Multicast VLAN, configure the VLAN ID of a multicast
VLAN as 3 and keep the other parameters as default on
Multicast→IGMP Snooping→Multicast VLAN page.
5 Check Multicast VLAN 3-5 and Multicast VLAN 3
will be displayed in the IGMP
Snooping Status table on the Multicast→I GM P
Snooping→Snooping Config page.
8.2 Multicast IP
In a network, receivers can join different multicast groups appropriate to their needs. The switch
forwards multicast streams based on multicast address table. The Multicast IP can be
implemented on Multicast IP Table, Static Multicast IP page.
8.2.1 Multicast IP Table
On this page you can view the multicast IP table on the switch.
Choose the menu Multicast→Multicast IP→Multicast IP Table to load the following page.
Figure 8-8 Multicast IP Table
The following entries are displayed on this screen:
Search Option
Multicast IP: Enter the multicast IP address the desired entry must carry.
VLAN ID: Enter the VLAN ID the desired entry must carry.
Port: Select the port number the desired entry must carry.
Typ e : Select the type the desired entry must carry.
All: Displays all multicast IP entries.
Static: Displays all static multicast IP entries.
Dynamic: Displays all dynamic multicast IP entries.
93
Multicast IP Table
Multicast IP Displays multicast IP address.
VLAN ID: Displays the VLAN ID of the multicast group.
Forward Port Displays the forward port of the multicast group.
Typ e : Displays the type of the multicast IP.
Note:
If the configuration on VLAN Config page and multicast VLAN page is changed, the switch will
clear up the dynamic multicast addresses in multicast address table and learn new addresses.
8.2.2 Static Multicast IP
Static Multicast IP table, isolated from dynamic multicast group and multicast filter, is not learned
by IGMP Snooping. It can enhance the quality and security for information transmission in some
fixed multicast groups.
Choose the menu Multicast→Multicast IP→Static Multicast IP to load the following page.
Figure 8-9 Static Multicast IP Table
The following entries are displayed on this screen:
Create Static Multicast
Multicast IP: Enter static multicast IP address.
VLAN ID: Enter the VLAN ID of the multicast IP.
Forward Port: Enter the forward port of the multicast group.
94
Search Option
Search Option:
Select the rules for displaying multicast IP table to find the desired
entries quickly.
All: Displays all static multicast IP entries.
Multicast IP:
Enter the multicast IP address the desired entry
must carry.
VLAN ID: Enter the VLAN ID the desired entry must carry.
Port: Enter the port number the desired entry must carry.
Static Multicast IP Table
Select: Select the de
sired entry to delete the corresponding static
multicast IP. It is multi-optional.
Multicast IP: Displays the multicast IP.
VLAN ID: Displays the VLAN ID of the multicast group.
Forward Port: Displays the forward port of the multicast group.
8.3 Multicast Filter
When IGMP Snooping is enabled, you can specified the multicast IP-range the ports can join so as
to restrict users ordering multicast programs via configuring multicast filter rules.
When applying for a multicast group, the host will send IGMP report message. After receiving the
report message, the switch will firstly check the multicast filter rules configured for the receiving
port. If the port can be added to the multicast group, it will be added to the multicast address table;
if the port cannot be added to the multicast group, the switch will drop the IGMP report message.
In that way, the multicast streams will not be transmitted to this port, which allows you to control
hosts joining the multicast group.
8.3.1 IP-Range
On this page you can figure the desired IP-ranges to be filtered.
Choose the menu Multicast→Multicast Filter→IP-Range to load the following page.
Figure 8-10 Multicast Filter
95
The following entries are displayed on this screen:
Create IP-Range
IP Range ID: Enter the IP-range ID.
Start Multicast IP: Enter start multicast IP of the IP-range you set.
End Multicast IP: Enter end multicast IP of the IP-range you set.
IP-Range Table
IP-
Range ID Select:
Click the Select button to quick-
select the corresponding
IP-range ID based on the ID number you entered.
Select:
Select the desired entry to delete or modify the corresponding
IP-range. It is multi-optional.
IP-Range ID: Displays IP-range ID.
Start Multicast IP: Displays start multicast IP of the IP-range.
End Multicast IP: Displays end multicast IP of the IP-range.
8.3.2 Port Filter
On this page you can configure the multicast filter rules for port. Take the configuration on this
page and the configuration on IP-Range page together to function to implement multicast filter
function on the switch.
Choose the menu Multicast→Multicast Filter→Port Filter to load the following page.
Figure 8-11 Port Filter
The following entries are displayed on this screen:
Port Filter Config
Port Sele ct: Click the Select button to quick-select
the corresponding port
based on the port number you entered.
96
Select: Select the desired port for multicast filtering. It is multi-optional.
Port: Displays the port number.
Filter: Select Enable/Disable multicast filtering feature on the port.
Action Mode:
Select the action mode to process multicast packets when the
multicast IP is in the filtering IP-range.
Permit: Only the multicast packets whose multicast IP is in
the IP-range will be processed.
Deny: Only the multicast packets whose multicast IP is not
in the IP-range will be processed.
Bound IP-Range (ID): Enter the IP-rang ID the port will be bound to.
Max Groups:
Specify the maximum number of multicast groups to prevent
some ports taking up too much bandwidth.
LAG: Displays the LAG number which the port belongs to.
Note:
1. Multicast Filter feature can only have effect on the VLAN with IGMP Snooping enabled.
2. Multicast Filter feature has no effect on static multicast IP.
3. Up to 15 IP-Ranges can be bound to one port.
Configuration Procedure:
Step Operation Description
1 Configure IP-Range Required. Configure IP-
Range to be filtered on
Multicast→Multicast Filter→IP-Range page.
2
Configure multicast filter
rules for ports
Optional. Configure multicast filter rules for ports on
Multicast→Multicast Filter→Port Filter page.
8.4 Packet Statistics
On this page you can view the multicast data traffic on each port of the switch, which facilitates you
to monitor the IGMP messages in the network.
97
Choose the menu Multicast→Packet Statistics to load the following page.
Figure 8-12 Packet Statistics
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh: Select Enable/Disable auto refresh feature.
Refresh Period: Enter the time from 3 to 300 in
seconds to specify the auto refresh
period.
IGMP Statistics
Port Sele ct: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Port: Displays the port number of the switch.
Query Packet: Displays the number of query packets the port received.
Report Packet (V1): Displays the number of IGMPv1 report packets the port received.
Report Packet (V2): Displays the number of IGMPv2 report packets the port received.
Report Packet (V3): Displays the number of IGMPv3 report packets the port received.
Leave Packet: Displays the number of leave packets the port received.
Error Packet: Displays the number of error packets the port received.
Return to CONTENTS
98
Chapter 9 QoS
QoS (Quality of Service) functions to provide different quality of service for various network
applications and requirements and optimize the bandwidth resource distribution so as to provide a
network service experience of a better quality.
QoS
This switch classifies the ingress packets, maps the packets to different priority queues and then
forwards the packets according to specified scheduling algorithms to implement QoS function.
Figure 9-1 QoS function
Traffic classification: Identifies packets conforming to certain characters according to certain
rules.
Map: The user can map the ingress packets to different priority queues based on the priority
modes. This switch implements three priority modes based on port, on 802.1P and on DSCP.
Queue scheduling algorithm: When the network is congested, the problem that many packets
compete for resources must be solved, usually in the way of queue scheduling. The switch
supports four schedule modes: SP, WRR, SP+WRR and Equ.
Priority Mode
This switch implements three priority modes based on port, on 802.1P and on DSCP. By default, the
priority mode based on port is enabled and the other two modes are optional.
1. Port Priority
Port priority is a priority level of the port. After port priority is configured, the data stream will be mapped
to the egress queues directly according to the priority level of the port.
99
2. 802.1P Priority
Figure 9-2 802.1Q frame
As shown in the figure above, each 802.1Q Tag has a Pri field, comprising 3 bits. The 3-bit priority
field is 802.1p priority in the range of 0 to 7. 802.1P priority determines the priority of the packets
based on the Pri value. On the Web management page of the switch, you can configure different
priority tags mapping to the corresponding priority levels, and then the switch determine which
packet is sent preferentially when forwarding packets. The switch processes untagged packets
based on the default priority mode.
3. DSCP Priority
Figure 9-3 IP datagram
As shown in the figure above, the ToS (Type of Service) in an IP header contains 8 bits. The first
three bits indicate IP precedence in the range of 0 to 7. RFC2474 re-defines the ToS field in the IP
packet header, which is called the DS field. The first six bits (bit 0-bit 5) of the DS field indicate
DSCP precedence in the range of 0 to 63. The last 2 bits (bit 6 and bit 7) are reserved. On the Web
management page, you can configure different DS field mapping to the corresponding priority
levels. Non-IP datagram with 802.1Q tag are mapped to different priority levels based on 802.1P
priority mode; the untagged non-IP datagram are mapped based on port priority mode.
Schedule Mode
When the network is congested, the problem that many packets compete for resources must be
solved, usually in the way of queue scheduling. The switch implements four scheduling queues,
TC0, TC1, TC2 and TC3. TC0 has the lowest priority while TC3 has the highest priority. The switch
provides four schedule modes: SP, WRR, SP+WRR and Equ.
1. SP-Mode: St r ic t-Priority Mode. In this mode, the queue with higher priority will occupy the
whole bandwidth. Packets in the queue with lower priority are sent only when the queue with
higher priority is empty. The switch has four egress queues labeled as TC0, TC1, TC2 and
TC3. In SP mode, their priorities increase in order. TC3 has the highest priority. The
disadvantage of SP queue is that: if there are packets in the queues with higher priority for a
long time in congestion, the packets in the queues with lower priority will be “starved to death”
because they are not served.
100
Figure 9-4 SP-Mode
2. WRR-Mode: Weight Round Robin Mode. In this mode, packets in all the queues are sent in
order based on the weight value for each queue and every queue can be assured of a certain
service time. The weight value indicates the occupied proportion of the resource. WRR queue
overcomes the disadvantage of SP queue that the packets in the queues with lower priority
cannot get service for a long time. In WRR mode, though the queues are scheduled in order,
the service time for each queue is not fixed, that is to say, if a queue is empty, the next queue
will be scheduled. In this way, the bandwidth resources are made full use of. The default
weight value ratio of TC0, TC1, TC2 and TC3 is 1:2:4:8.
Figure 9-5 WRR-Mode
3. SP+WRR-Mode: Str i ct -Priority + Weight Round Robin Mode. In this mode, this switch
provides two scheduling groups, SP group and WRR group. Queues in SP group and WRR
group are scheduled strictly based on strict-priority mode while the queues inside WRR group
follow the WRR mode. In SP+WRR mode, TC3 is in the SP group; TC0, TC1 and TC2 belong
to the WRR group and the weight value ratio of TC0, TC1 and TC2 is 1:2:4. In this way, when
scheduling queues, the switch allows TC3 to occupy the whole bandwidth following the SP
mode and the TC0, TC1 and TC2 in the WRR group will take up the bandwidth according to
their ratio 1:2:4.
4. Equ-Mode: Equal-Mode. In this mode, all the queues occupy the bandwidth equally. The
weight value ratio of all the queues is 1:1:1:1.
101
The QoS module is mainly for traffic control and priority configuration, including two submenus:
DiffServ and Bandwidth Control.
9.1 DiffServ
This switch classifies the ingress packets, maps the packets to different priority queues and then
forwards the packets according to specified scheduling algorithms to implement QoS function.
This switch implements three priority modes based on port, on 802.1P and on DSCP, and supports
four queue scheduling algorithms. The port priorities are labeled as TC0, TC1, TC2 and TC3.
The DiffServ function can be implemented on Po r t Priority, 802.1P Priority, DSCP Priority and
Schedule Mode pages.
9.1.1 Port Priority
On this page you can configure the port priority.
Choose the menu QoS→DiffServ→Port Priority to load the following page.
Figure 9-6 Port Priority Config
The following entries are displayed on this screen:
Port Priority Config
Select: Select the desired port to configure its priority. It is multi-optional.
Port: Displays the physical port number of the switch.
Priority: Specify the priority for the port.
LAG: Displays the LAG number which the port belongs to.
102
Configuration Procedure:
Step Operation Description
1 Select the port priority Required. On QoS→DiffServ→Port Priority page,
configure the port priority.
3 Select a schedule mode Required. On QoS→DiffServ→Schedule Mode page,
select a schedule mode.
9.1.2 802.1P/CoS Mapping
On this page you can configure 802.1P priority. 802.1P gives the Pri field in 802.1Q tag a
recommended definition. This field is used to divide packets into 8 priorities. When 802.1P Priority is
enabled, the packets with 802.1Q tag are mapped to different priority levels based on 802.1P priority
mode. The untagged packets are mapped based on port priority mode.
Choose the menu QoS→DiffServ→802.1P Priority to load the following page.
Figure 9-7 802.1P Priority
The following entries are displayed on this screen:
802.1P Priority Config
802.1P Priority: Select Enable/Disable 802.1P Priority.
Priority Level
Ta g -id/CoS-id: Indicates the precedence level defined by IEEE802.1P or
the CoS
ID.
Queue TC-id:
Indicates the priority level of egress queue the packets with tag
and CoS-
id are mapped to. The priority levels of egress queue are
labeled as TC0, TC1, TC2 and TC3.
Note:
To complete QoS function configuration, you have to go to the Schedule Mode page to select a
schedule mode after the configuration is finished on this page.
103
Configuration Procedure:
Step Operation Description
1 Log on to the 802.1P/Co S
Mapping page
2
Enable 802.1P priority
function
Required. By default, the 802.1P priority function is
disabled.
3
Map the 802.1P priority tag to
the priority level
Required. Select 802.1P priority tag and the
corresponding priority level.
4 Select a schedule mode Required. Log on to the Sche dule Mode
page to
select a schedule mode.
9.1.3 DSCP Priority
On this page you can configure DSCP priority. DSCP (DiffServ Code Point) is a new definition to IP
ToS field given by IEEE. This field is used to divide IP datagram into 64 priorities. When DSCP
Priority is enabled, IP datagram are mapped to different priority levels based on DSCP priority
mode; non-IP datagram with 802.1Q tag are mapped to different priority levels based on 802.1P
priority mode if 802.1P Priority mode is enabled; the untagged non-IP datagram are mapped based
on port priority mode.
Choose the menu QoS→DiffServ→DSCP Priority to load the following page.
Figure 9-8 DSCP Priority
The following entries are displayed on this screen:
DSCP Priority Config
DSCP Priority: Select Enable or Disable DSCP Priority.
104
Priority Level
DSCP:
Indicates the priority determined by the DS region of IP datagram.
It ranges from 0 to 63.
Priority Level:
Indicates the priority level the packets with tag are mapped to. The
priority levels are labeled as TC0, TC1, TC2 and TC3.
Note:
To complete QoS function configuration, you have to go to the Schedule Mode page to select a
schedule mode after the configuration is finished on this page.
Configuration procedure:
Step Operation Description
1 Log on to the DSCP Priority page
2 Enable DP priority function
Required. By default, the DSCP priority function is
disabled.
3
Map the DSCP priority to the
priority level
Required. Select DSCP priority and the
corresponding priority level.
4 Select a schedule mode Required. Log on to the Schedule Mode
page to
select a schedule mode.
9.1.4 Schedule Mode
On this page you can select a schedule mode for the switch. When the network is congested, the
problem that many packets compete for resources must be solved, usually in the way of queue
scheduling. The switch will control the forwarding sequence of the packets according to the priority
queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0,
TC1… TC3.
Choose the menu QoS→DiffServ→Schedule Mode to load the following page.
Figure 9-9 Schedule Mode
The following entries are displayed on this screen:
Schedule Mode Config
SP-Mode: St r ic t -
Priority Mode. In this mode, the queue with higher priority
will occupy the wh
ole bandwidth. Packets in the queue with lower
priority are sent only when the queue with higher priority is empty.
WRR-Mode:
Weight Round Robin Mode. In this mode, packets in all the
queues are sent in order based on the weight value for each
queue. The
weight value ratio of TC0, TC1, TC2 and TC3 is
1:2:4:8.
105
SP+WRR-Mode: St r ic t -
Priority + Weight Round Robin Mode. In this mode, this
switch provides two scheduling groups, SP group and WRR
group. Queues in SP group and WRR group are scheduled
strictly based on strict-
priority mode while the queues inside
WRR group follow the WRR mode. In SP+WRR mode, TC3 is in
the SP group; TC0, TC1 and TC2 belong to the WRR group and
the weight value ratio of TC0, TC1 and TC2 is 1:2:4. In this way,
when scheduling queues,
the switch allows TC3 to occupy the
whole bandwidth following the SP mode and the TC0, TC1 and
TC2 in the WRR group will take up the bandwidth according to
their ratio 1:2:4.
Equ-Mode: Equal-
Mode. In this mode, all the queues occupy the bandwidth
equally. The weight value ratio of all the queues is 1:1:1:1.
9.2 Bandwidth Control
Bandwidth function, allowing you to control the traffic rate and broadcast flow on each port to
ensure network in working order, can be implemented on Rate Limit and Storm Control pages.
9.2.1 Rate Limit
Rate limit functions to control the ingress/egress traffic rate on each port via configuring the
available bandwidth of each port. In this way, the network bandwidth can be reasonably distributed
and utilized.
Choose the menu QoS→Bandwidth Control→Rate Limit to load the following page.
Figure 9-10 Rate Limit
106
The following entries are displayed on this screen:
Rate Limit Config
Port Sele ct: Click the Select button to quick-select the correspon
ding port
based on the port number you entered.
Select: Select the desired port for Rate configuration. It is multi-optional.
Port: Displays the port number of the switch.
Ingress Rate (bps): Configure the bandwidth for receiving packets on the port. Yo
u
can select a rate from the dropdown list or
select "Manual" to set
Ingress rate, the system will automatically select integral multiple
of 64Kbps that closest to the rate you entered as the real Ingress
rate.
Egress Rate(bps): Configure the bandwidth for sending packets on the port.
You can
select a rate from the dropdown list or
select "Manual" to set
Egress rate, the system will automatically select integral multiple
of 64Kbps that closest to the rate you entered as the real Egress
rate.
LAG: Displays the LAG number which the port belongs to.
Note:
1. If you enable ingress rate limit feature for the storm control-enabled port, storm control feature
will be disabled for this port.
2. When selecting "Manual" to set Ingress/Egress rate, the system will automatically select
integral multiple of 64Kbps that closest to the rate you entered as the real Ingress/Egress rate.
For example, if you enter 1000Kbps for egress rate, the system will automatically select
1024Kbps as the real Egress rate.
3. When egress rate limit feature is enabled for one or more ports, you are suggested to disable
the flow control on each port to ensure the switch works normally.
9.2.2 Storm Control
Storm Control function allows the switch to filter broadcast, multicast and UL frame in the network.
If the transmission rate of the three kind packets exceeds the set bandwidth, the packets will be
automatically discarded to avoid network broadcast storm.
107
Choose the menu QoS→Bandwidth Control→Storm Control to load the following page.
Figure 9-11 Storm Control
The following entries are displayed on this screen:
Storm Control Config
Port Sele ct: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Select: Sel
ect the desired port for Storm Control configuration. It is
multi-optional.
Port: Displays the port number of the switch.
Broadcast Rate
(bps):
Select the bandwidth for receiving broadcast packets on the port.
The packet traffic exceeding the bandwidth w
ill be discarded.
Select Disable to disable the storm control function for the port.
Mulitcast Rate
(bps):
Select the bandwidth for receiving multicast packets on the port.
The packet traffic exceeding the bandwidth will be discarded.
Select Disable to disable the storm control function for the port.
UL-Fram
e Rate
(bps):
Select the bandwidth for receiving UL-
Frame on the port. The
packet traffic exceeding the bandwidth will be discarded. Select
Disable to disable the storm control function for the port.
LAG: Displays the LAG number which the port belongs to.
Note:
If you enable storm control feature for the ingress rate limit-enabled port, ingress rate limit feature
will be disabled for this port.
108
9.3 Voice VLAN
Voice VLANs are configured specially for voice data stream. By configuring Voice VLANs and
adding the ports with voice devices attached to voice VLANs, you can perform QoS-related
configuration for voice data, ensuring the transmission priority of voice data stream and voice
quality.
OUI Address (Organizationally unique identifier address)
The switch can determine whether a received packet is a voice packet by checking its source MAC
address. If the source MAC address of a packet complies with the OUI addresses configured by
the system, the packet is determined as voice packet and transmitted in voice VLAN.
An OUI address is a unique identifier assigned by IEEE (Institute of Electrical and Electronics
Engineers) to a device vendor. It comprises the first 24 bits of a MAC address. You can recognize
which vendor a device belongs to according to the OUI address. The following table shows the
OUI addresses of several manufacturers. The following OUI addresses are preset of the switch by
default.
Number
OUI Address Vendor
1 00-01-e3-00-00-00 Siemens phone
2 00-03-6b-00-00-00 Cisco phone
3 00-04-0d-00-00-00 Avaya phone
4 00-60-b9-00-00-00 Philips/NEC phone
5 00-d0-1e-00-00-00 Pingtel phone
6 00-e0-75-00-00-00 Polycom phone
7 00-e0-bb-00-00-00 3com phone
Table 9-1 OUI addresses on the switch
Port Voice VLAN Mode
A voice VLAN can operate in two modes: automatic mode and manual mode.
Automatic Mode: In this mode, the switch automatically adds a port which receives voice packets
to voice VLAN and determines the priority of the packets through learning the source MAC of the
UNTAG packets sent from IP phone when it is powered on. The aging time of voice VLAN can be
configured on the switch. If the switch does not receive any voice packet on the ingress port within
the aging time, the switch will remove this port from voice VLAN. Voice ports are automatically
added into or removed from voice VLAN.
Manual Mode: You need to manually add the port of IP phone to voice VLAN, and then the switch
will assign ACL rules and configure the priority of the packets through learning the source MAC
address of packets and matching OUI address.
109
In practice, the port voice VLAN mode is configured according to the type of packets sent out from
voice device and the link type of the port. The following table shows the detailed information.
Port Voice
VLAN Mode
Vo i c e
St r e a m Typ e
Link type of the port and processing mode
Automatic Mode
TAG voice
stream
Untagged: Not supported.
Tagged: Supported. The default VLAN of the port cannot
be
voice VLAN.
UNTAG voice
stream
Untagged: Supported.
Tagged: Not supported.
Manual Mode
TAG voice
stream
Untagged: Not supported.
Tagged：Supported. The default VLAN of the port should not
be voice VLAN.
UNTAG voice
stream
Untagged: Supported.
Tagged: Not supported.
Table 9-2 Port voice VLAN mode and voice stream processing mode
Security Mode of Voice VLAN
When voice VLAN is enabled for a port, you can configure its security mode to filter data stream. If
security mode is enabled, the port just forwards voice packets, and discards other packets whose
source MAC addresses do not match OUI addresses. If security mode is not enabled, the port
forwards all the packets.
Se curity M ode
Packet Type Processing Mode
Enable
UNTAG packet
When the source MAC address of the packet is the OUI
address that can be identified, the packet can be
trans
mitted in the voice VLAN. Otherwise, the packet will
be discarded.
Packet with voice
VLAN TAG
Packet with other
VLAN TAG
The processing mode for the device to deal with the packet
is determined by whether the port permits the VLAN or not,
independent of voice VLAN security mode.
Disable
UNTAG packet
Do not check the source MAC address of the packet and all
the packets can be transmitted in the voice VLAN.
Packet with voice
VLAN TAG
Packet with other
VLAN TAG
The processing mode for the dev
ice to deal with the packet
is determined by whether the port permits the VLAN or
not, independent of voice VLAN security mode.
Table 9-3 Security mode and packets processing mode
Note:
Don’t transmit voice stream together with other business packets in the voice VLAN except for
some special requirements.
The Voice VLAN function can be implemented on Global Config, Port Config and OUI Config
pages.
110
9.3.1 Global Config
On this page, you can configure the global parameters of the voice VLAN, including VLAN ID and
aging time.
Choose the menu QoS→Voice VLAN→Global Config to load the following page.
Figure 9-12 Global Configuration
The following entries are displayed on this screen:
Global Config
Vo i c e VLAN: Select Enable/Disable Voice VLAN function.
VLAN ID: Enter the VLAN ID of the voice VLAN.
Aging Time:
Specifies the living time of the member port in auto mode after the
OUI address is aging out.
Priority: Select the priority of the port when sending voice data.
9.3.2 Port Config
Before the voice VLAN function is enabled, the parameters of the ports in the voice VLAN should
be configured on this page.
Choose the menu QoS→Voice VLAN→Port Config to load the following page.
Figure 9-13 Port Config
111
Note:
To enable voice VLAN function for the LAG member port, please ensure its member state accords
with its port mode.
If a port is a member port of voice VLAN, changing its port mode to be “Auto” will make the port
leave the voice VLAN and will not join the voice VLAN automatically until it receives voice streams.
The following entries are displayed on this screen:
Port Config
Port Select: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Select:
Select the desired port for voice VLAN configuration. It is
multi-optional.
Port: Displays the port number of the switch.
Port Mode: Select the mode for the port to join the voice VLAN.
Auto:
In this mode, the switch automatically adds a port to the
voice VLAN or removes a port from the voice VLAN by
checking whether the port receives voice data or not.
Manual: In this mode, you can manu
ally add a port to the
voice VLAN or remove a port from the voice VLAN.
Security Mode: Configure the security mode for forwarding packets.
Disable: All packets are forwarded.
Enable: Only voice data are forwarded.
Member State: Displays the state of the port in the current voice VLAN.
LAG: Displays the LAG number which the port belongs to.
9.3.3 OUI Config
The switch supports OUI creation and adds the MAC address of the special voice device to the
OUI table of the switch. The switch determines whether a received packet is a voice packet by
checking its OUI address. The switch analyzes the received packets. If the packets recognized as
voice packets, the access port will be automatically added to the Voice VLAN.
112
Choose the menu QoS→Voice VLAN→OUI Config to load the following page.
Figure 9-14 OUI Configuration
The following entries are displayed on this screen:
Create OUI
OUI: Enter the OUI address of the voice device.
Mask: Enter the OUI address mask of the voice device.
Description: Give a description to the OUI for identification.
OUI Table
Select: Select the desired entry to view the detailed information.
OUI: Displays the OUI address of the voice device.
Mask: Displays the OUI address mask of the voice device.
Description: Displays the description of the OUI.
Configuration Procedure of Voice VLAN:
Step Operation Description
1
Configure the link type of
the port
Required. On VLAN→802.1Q VLAN→V L AN
Config
page, configure the link type of ports of the voice device.
2
Create VLAN Required. On VLAN→802.1Q VLAN→V LAN
Config
page, click the Create button to create a VLAN.
3
Add OUI address Optional. On QoS→Voice VLAN→OUI Config page, you
can check whether the switch is supporting the OUI
template or not. If not, please add the OUI address.
113
Step Operation Description
4
Configure the parameters
of the ports in voice VLAN.
Required. On QoS→Voice VLAN→Port Config
page,
configure the parameters of the ports in voice VLAN.
5
Enable Voice VLAN Required. On QoS→Voice VLAN→Global Config
page,
configure the global parameters of voice VLAN.
Return to CONTENTS
114
Chapter 10 PoE
PoE (Power over Ethernet) technology describes a system to transmit electrical power along with
data to remote devices over standard twisted-pair cable in an Ethernet network. It is especially
useful for supplying power to IP telephones, wireless LAN access points, cameras and so on.
Composition
A PoE system usually consists of PSE and PD.
PSE: Power sourcing equipment (PSE) is a device such as a switch that provides power on the
Ethernet cable to the linked device.
PD: A powered device (PD) is a device accepting power from the PSE and thus consumes energy.
PDs falls into two types, standard PDs and nonstandard PDs. Standard PDs refer to the powered
devices that comply with IEEE 802.3af and IEEE 802.3at. Examples include wireless LAN access
points, IP Phones, IP cameras, network hubs, embedded computers etc.
Advantage
Cheap cabling: The remote device such as cameras can be powered by PSE in no need
of prolonging its power cord additionally and Ethernet cable is much cheaper than AC
wire or power cord.
Easy to connect: PoE uses only one Ethernet cable with no need of external power
supply.
Reliable: A powered device can be either powered by PSE using Ethernet cable or
powered through the provided power adapter. It is very convenient to provide a backup
power supply for the PDs.
Flexibility: In compliance with IEEE 802.3af and IEEE 802.3at, global organizations can
deploy PoE everywhere without concern for any local variance in AC power standards,
outlets, plugs, or reliability.
Wide use: It can be applied to wireless LAN access points, IP Phones, IP cameras,
network hubs, embedded computers etc.
T1500-28PCT is a Power Sourcing Equipment (PSE). All the Auto-Negotiation RJ45 ports on the
switch support Power over Ethernet (PoE) function, which can automatically detect and supply
power for those powered devices (PDs) complying with IEEE 802.3af and IEEE 802.3at. The
maximum power T1500-28PCT can supply is 180W and the maximum power each PoE port can
supply is 30W.
PoE function can be configured in the two sections, PoE Config and PoE Time -Range.
10.1 PoE Config
All the RJ45 ports on the switch can be configured to supply power for the powered devices that
comply with IEEE 802.3af and IEEE 802.3at. As the power every port or the system can provide is
limited, some attributes should be set to make full use of the power and guarantee the adequate
power to the linked PDs. When the power exceeds the maximum power limit or the power is
inadequate to power the device, the switch may disconnect the power supply to the PD linked to
the port with lower priority. When detecting a PD is unplugged, the switch will stop supplying the
power to the PD.
PoE Config, mainly for PoE attributes configuration, is implemented on PoE Config and PoE
Profile pages.
115
10.1.1 PoE Config
On this page, you can configure the parameters to implement PoE function.
Choose the menu PoE→PoE Config→PoE Config to load the following page.
Figure 10-1 PoE Config for T1500-28PCT
The following items are displayed on this screen:
Global Config
System Power Limit:
Specify the max power the PoE switch can supply.
Syste m Powe r
Consumption:
Displays the PoE switch's real time system power consumption.
Syste m Powe r
Re main:
Displays the PoE switch's real time remaining system power.
Port Config
Port Select: Click the Select button to quick-
select the corresponding entry
based on the port number you entered.
Select: Select the desired port to configure its parameters.
Port: Displays the port number.
PoE Status: Select to disable/enable the PoE feature for the corr
esponding
port. If set enable, the corresponding port can supply power to the
linked PD (Powered Device).
PoE Priority:
The priority levels include High, Middle and Low in descending
order. When the supply power exceeds the system power limit,
the PD linked to the port with lower priority will be disconnected.
Power Limit
(0.1w-30w):
Defines the max power the corresponding port can supply. Class1
represents 4w, Class2 represents 7w,
Class3 represents 15.4w
and Class4 represents 30w.
116
Time Range: Select the time range for the PoE port to supply power. If
No limit
is selected, the PoE port will supply power all the time.
PoE Profile : Select the profile
you want to apply to the selected port. If a PoE
Profile is selected, the three attributes including PoE S
tatus, PoE
Priority and Power Limit are not available.
Power (W): Displays the port's real time power supply.
Current (mA): Displays the port's real time current.
Voltage (V): Displays the port's real time voltage.
PD Class: Displays the class the linked PD (Powered Device) belongs to.
Powe r Status: Displays the port's real time power status.
10.1.2 PoE Profile
PoE (Power over Ethernet) Profile is a short cut for the configuration of the PoE port. You can
create some profiles to be applied to the ports. In a profile, the PoE status, PoE priority and Power
limit are configured.
Choose the menu PoE→PoE Config→Profile Profile to load the following page.
Figure 10-2 Profile Config
The following items are displayed on this screen:
Create PoE Profile
Profile Name: Enter the name of the profile.
PoE Status:
Select to the enable/disable PoE feature for the corresponding
port. If set enable,
the port may supply power to the linked PD
(Power Device).
PoE Priority:
The priority levels include High, Middle and Low in descending
order. When the supply power e
xceeds the system power limit,
the PD linked to the port with lower priority will be disconnected.
Power Limit:
Defines the max power the corresponding port can supply. Class1
represents 4 w, Class2 represents 7 w, Class3 represents 15.4w,
and Class4 represents 30w. (for T1500-28PCT)
117
PoE Profile
Select: Select the desired profile to delete.
Profile Name: Displays the name of the profile.
PoE Status: Displays the PoE status of the port in the profile.
PoE Priority: Displays the PoE priority of the port in the profile.
Power Limit: Displays the max power the port in the profile can supply.
10.2 PoE Time-Range
A time -range based PoE enables you to implement PoE power supply by differentiating the
time-ranges. A time-range can be specified for each port. The port will not supply power when the
specified time-range is configured and the system time is not within the time-range.
On this switch absolute time, week time and holiday can be configured. Configure an absolute time
section in the form of “the start date to the end date” to make the port based on this time range
supply power; configure a week time section to make the port supply based on this time range on
the fixed days of the week; configure a holiday section and select Exclude Holiday to make the port
based on this time range not supply power on some special days. In each time-range, four
time-slices can be configured.
The Time-Range configuration can be implemented on PoE Time -Range Summary, PoE
Time -Range Create and PoE Holiday Config pages.
10.2.1 Time-Range Summary
On this page you can view or delete the current time-ranges.
Choose the menu PoE→PoE Ti me -Range →PoE Ti me -Range Summary to load the following
page.
Figure 10-3 Time-Range Table
The following items are displayed on this screen:
Time -Range Table
Select: Select the desired entry to delete the corresponding time-range.
Index: Displays the index of the time-range.
Time -Range Name: Displays the name of the time-range.
Slice: Displays the time-slice of the time-range.
Mode: Displays the mode the time-range adopts.
Operation: Click Edit to modify this time-range and click Detail
to display the
complete information of this time–range.
118
10.2.2 PoE Time-Range Create
On this page you can create time-ranges.
Choose the menu PoE→PoE Time -Range→PoE Time -Range Create to load the following page.
Figure 10-4 Time-Range Create
Note:
To successfully configure time-ranges, please firstly specify time-slices and then time-ranges.
The following items are displayed on this screen:
Create Time-Range
Name : Enter the name of the time-range for time identification.
Exclude Holiday: Select Exclude Holiday, and the port based on this time-range
may not supply power when the system time is within the holiday
Absolute: Select Absolute to configure absolute time-range. T
he port based
on this time-range will supply power based on this time-range
when the system time is within the absolute time-range.
Week: Select Week to configure week time-range. T
he port based on this
time-range will supply power based on this time-
range when the
system time is within the week time-range.
Create Time-Slice
Start Time: Set the start time of the time-slice.
End Time : Set the end time of the time-slice.
Time -Slice Table
Index: Displays the index of the time-slice.
Start Time: Displays the start time of the time-slice.
End Time: Displays the end time of the time-slice.
Delete: Click the Delete button to delete the corresponding time-slice.
119
10.2.3 PoE Holiday Config
Holiday mode is applied as a different secured access control policy from the week mode. On this
page you can define holidays according to your work arrangement.
Choose the menu PoE→PoE Time -Range→PoE Holiday Cre ate to load the following page.
Figure 10-5 Holiday Configuration
The following entries are displayed on this screen:
Create Holiday
Start Date: Specify the start date of the holiday.
End Date: Specify the end date of the holiday.
Holiday Name: Enter the name of the holiday.
Holiday Table
Select: Select the desired entry to delete the corresponding holiday.
Index: Displays the index of the holiday.
Holiday Name: Displays the name of the holiday.
Start Date: Displays the start date of the holiday.
End Date: Displays the end date of the holiday.
Return to CONTENTS
120
Chapter 11 ACL
11.1 ACL Config
An ACL may contain a number of rules, and each rule specifies a different package range. Packets
are matched in match order. Once a rule is matched, the switch processes the matched packets
taking the operation specified in the rule without considering the other rules, which can enhance
the performance of the switch.
The ACL Config function can be implemented on ACL Summary, ACL Create, M AC ACL,
Standard-IP ACL, Exte nd-IP ACL and Combined ACL pages.
11.1.1 ACL Summary
On this page, you can view the current ACLs configured in the switch.
Choose the menu ACL→ACL Config→ACL Summary to load the following page.
Figure 11-1 ACL Summary
The following entries are displayed on this screen:
Search Option
Select ACL: Select the ACL you have created
ACL Typ e : Displays the type of the ACL you select.
Rule Order: Displays the rule order of the ACL you select.
Rule Table
Display the rule table of the ACL you have selected. Here you can edit the rules, view the details of
them, and move them up and down.
11.1.2 ACL Create
On this page you can create ACLs.
121
Choose the menu ACL→ACL Config→ACL Create to load the following page.
Figure 11-2 ACL Create
The following entries are displayed on this screen:
Create ACL
ACL ID: Enter ACL ID of the ACL you want to create.
Rule Order: User Config order is set to be match order in this ACL.
11.1.3 MAC ACL
MAC ACLs analyze and process packets based on a series of match conditions, which can be the
source MAC addresses and destination MAC addresses carried in the packets.
Choose the menu ACL→ACL Config→M AC ACL to load the following page.
Figure 11-3 Create MAC Rule
The following entries are displayed on this screen:
Create MAC ACL
ACL ID: Select the desired MAC ACL for configuration.
Rule ID: Enter the rule ID.
Operation:
Select the operation for the switch to process packets which match the
rules.
Permit: Forward packets.
Deny: Discard Packets.
S-M AC: Enter the source MAC address contained in the rule.
122
D-M AC: Enter the destination MAC address contained in the rule.
M ASK:
Enter MAC address mask. If it is set to 1, it must strictly match the
address.
11.1.4 Standard-IP ACL
Standard-IP ACLs analyze and process data packets based on a series of match conditions, which
can be the source IP addresses and destination IP addresses carried in the packets.
Choose the menu ACL→ACL Config→Standard-IP ACL to load the following page.
Figure 11-4 Create Standard-IP Rule
The following entries are displayed on this screen:
Create Standard-IP ACL
ACL ID: Select the desired Standard-IP ACL for configuration.
Rule ID: Enter the rule ID.
Operation:
Select the operation for the switch to process packets which match the
rules.
Permit: Forward packets.
Deny: Discard Packets.
S-IP: Enter the source IP address contained in the rule.
D-IP: Enter the destination IP address contained in the rule.
Mask:
Enter IP address mask. If it is set to 1, it must strictly match the
address.
11.1.5 Extend-IP ACL
Extend-IP ACLs analyze and process data packets based on a series of match conditions, which
can be the source IP addresses, destination IP addresses, IP protocol and other information of this
sort carried in the packets.
123
Choose the menu ACL→ACL Config→Exte nd-IP ACL to load the following page.
Figure 11-5 Create Extend-IP Rule
The following entries are displayed on this screen:
Create Extend-IP ACL
ACL ID: Select the desired Extend-IP ACL for configuration.
Rule ID: Enter the rule ID.
Operation:
Select the operation for the switch to process packets which match the
rules.
Permit: Forward packets.
Deny: Discard Packets.
S-IP: Enter the source IP address contained in the rule.
D-IP: Enter the destination IP address contained in the rule.
Mask:
Enter IP address mask. If it is set to 1, it must strictly match the
address.
IP Protocol: Select IP protocol contained in the rule.
S-Port:
Configure TCP/IP source port contained in the rule when TCP/UDP is
selected from the pull-down list of IP Protocol.
D-Port:
Configure TCP/IP destination port contained in the rule when
TCP/UDP is selected from the pull-down list of IP Protocol.
11.1.6 Combined ACL
Combined ACLs analyze and process data packets based on a series of match conditions,
including the source MAC addresses, destination MAC addresses, source IP addresses and
destination IP addresses carried in the packets.
124
Choose the menu ACL→ACL Config→Combined ACL to load the following page.
Figure 11-6 Create Combined ACL
The following entries are displayed on this screen:
Create Combined Rule
ACL ID: Select the desired Combined ACL for configuration.
Rule ID: Enter the rule ID.
Operation:
Select the operation for the switch to process packets which match the
rules.
Permit: Forward packets.
Deny: Discard Packets.
S-M AC: Enter the source MAC address contained in the rule.
D-M AC: Enter the destination MAC address contained in the rule.
S-IP: Enter the source IP address contained in the rule.
D-IP: Enter the destination IP address contained in the rule.
Mask: Enter the MAC/IP
address mask. If it is set to 1, it must strictly match
the address.
11.2 Policy Config
A Policy is used to control the data packets those match the corresponding ACL rules by
configuring ACLs and actions together for effect. The operations here include stream mirror,
stream condition, QoS remarking and redirect.
The Policy Config can be implemented on Policy Summary, Police Create and Act ion Cre ate
pages.
11.2.1 Policy Summary
On this page, you can view the ACL and the corresponding operations in the policy.
125
Choose the menu ACL→Policy Config→Policy Summary to load the following page.
Figure 11-7 Policy Summary
The following entries are displayed on this screen:
Search Option
Select Policy:
Select name of the desired policy for view. If you want to delete the
desired policy, please click the Delete button.
Action Table
Select: Select the desired entry to delete the corresponding policy.
Index: Displays the index of the policy.
ACL ID: Displays the ID of the ACL contained in the policy.
11.2.2 Policy Create
On this page you can create the policy.
Choose the menu ACL→Policy Config→Policy Create to load the following page.
Figure 11-8 Create Policy
The following entries are displayed on this screen:
Create Policy
Policy Name: Enter the name of the policy.
11.2.3 Action Create
On this page you can add ACLs for the policy.
126
Choose the menu ACL→Policy Config→Action Create to load the following page.
Figure 11-9 Action Create
The following entries are displayed on this screen:
Create Act io n
Select Policy: Select the name of the policy.
Select ACL: Select the ACL for configuration in the policy.
11.3 Policy Binding
Policy Binding function can have the policy take its effect on a specific port/VLAN. The policy will
take effect only when it is bound to a port/VLAN. In the same way, the port/VLAN will receive the
data packets and process them based on the policy only when the policy is bound to the
port/VLAN.
The Policy Binding can be implemented on Binding Table, Port Binding and VLAN Binding
pages.
11.3.1 Binding Table
On this page view the policy bound to port/VLAN.
Choose the menu ACL→Policy Binding→Binding Table to load the following page.
Figure 11-10 Binding Table
The following entries are displayed on this screen:
Search Option
Show Mode: Select a show mode appropriate to your needs.
Policy Bind Table
Select:
Select the desired entry to delete the corresponding binding policy.
127
Index: Displays the index of the binding policy.
Policy Name: Displays the name of the binding policy.
Interface: Displays the port number or VLAN ID bound to the policy.
Direction: Displays the binding direction.
11.3.2 Port Binding
On this page you can bind a policy to a port.
Choose the menu ACL→Policy Binding→Port Binding to load the following page.
Figure 11-11 Bind the policy to the port
The following entries are displayed on this screen:
Port-Bind Config
Policy Name: Select the name of the policy you want to bind.
Port: Enter the number of the port you want to bind.
Port-Bind Table
Index: Displays the index of the binding policy.
Policy Name: Displays the name of the binding policy.
Port: Displays the number of the port bound to the corres
ponding policy.
Direction: Displays the binding direction.
11.3.3 VLAN Binding
On this page you can bind a policy to a VLAN.
128
Choose the menu ACL→Policy Binding→VLAN Binding to load the following page.
Figure 11-12 Bind the policy to the VLAN
The following entries are displayed on this screen:
VLAN-Bind Config
Policy Name: Select the name of the policy you want to bind.
VLAN ID: Enter the ID of the VLAN you want to bind.
VLAN-Bind Table
Index: Displays the index of the binding policy.
Policy Name: Displays the name of the binding policy.
VLAN ID: Displays the ID of the VLAN bound to the corresponding policy.
Direction: Displays the binding direction.
Configuration Procedure:
Step Operation Description
1
Configure ACL rules Required. On ACL→ ACL Config
configuration pages,
configure ACL rules to match packets.
2
Configure Policy Required. On ACL→Policy Config
configuration pages,
configure the policy to c
ontrol the data packets those match
the corresponding ACL rules.
3
Bind the policy to the
port/VLAN
Required. On ACL→Policy Binding
configuration pages,
bind the policy to the port/VLAN to make the policy effective
on the corresponding port/VLAN.
11.4 Application Example for ACL
Network Requirements
1. The manager of the R&D department can access to the forum of the company. The MAC
address of the manager is 00-64-A5-5D-12-C3.
2. The staff of the R&D department can visit the forum.
3. The staff of the marketing department cannot visit the forum.
4. The R&D department and marketing department cannot communicate with each other.
129
Network Diagram
Configuration Procedure
Step Operation Description
1
Configure for
requirement 1
On ACL→ACL Config→ACL Create page, create ACL 11.
On ACL→ AC L Co n f ig →M AC ACL page, select ACL 11,
create Rule 1,
configure the operation as Permit, configure the S-
MAC as
00-46-A5-5D-12-C3 and mask as FF-FF-FF-FF-FF-F F.
On AC L→Policy Config→Policy Create page, cr
eate a policy named
manager.
On ACL→Policy Config→Action Create
page, add ACL 11 to Policy
manager.
On ACL→Policy Binding→Port Binding
page, select Policy manager
to bind to port 3.
2
Configure for
requirement 2
and 4
On ACL→ACL Config→ACL Create page, create ACL 100.
On ACL→ACL Config→Standard-IP ACL
page, select ACL 100,
create Rule 1, configure operation as Deny, configure S-
IP as
10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.50.1
and mask as 255.255.255.0.
On ACL→ACL Config→Standard-IP ACL
page, select ACL 100,
create Rule 2, configure operation as Permit, configure S-
IP as
10.10.70.0 and mask as 255.255.255.0, configure D-IP as 10.10.88.5
and mask as 255.255.255.255.
On ACL→Policy Config→Policy Create
page, create a policy named
limit1.
On ACL→Policy Config→Action Create
page, add ACL 100 to Policy
limit1.
On ACL→Policy Binding→Port Binding
page, select Policy limit1 to
bind to port 3.
130
Step Operation Description
3
Configure for
requirement 3
and 4
On ACL→ACL Config→ACL Create page, create ACL 101.
On ACL→ACL Config→Standard-IP ACL
page, select ACL 101,
create Rule 4, configure operation as Deny, configure S-
IP as
10.10.50.0 and mask as 255.255.255.0, configure D-IP as 10.10.70.0
and mask as 255.255.255.0.
On ACL→ACL Config→Standard-IP ACL pag
e, select ACL 101,
create Rule 5, configure operation as Deny, configure S-
IP as
10.10.50.0 and mask as 255.255.255.0, configure D-IP as 10.10.88.5
and mask as 255.255.255.255.
On AC L→Policy Config→Policy Create
page, create a policy named
limit2.
On ACL→Policy Config→Action Create
page, add ACL 101 to Policy
limit2.
On ACL→Policy Binding→Port Binding
page, select Policy limit2 to
bind to port 4.
Return to CONTENTS
131
Chapter 12 SNMP
SNM P Ove rview
SNMP (Simple Network Management Protocol) has gained the most extensive application on the
UDP/IP networks. SNMP provides a management frame to monitor and maintain the network
devices. It is used for automatically managing the various network devices no matter the physical
differences of the devices. Currently, the most network management systems are based on SNMP.
SNMP is simply designed and convenient for use with no need of complex fulfillment procedures
and too much network resources. With SNMP function enabled, network administrators can easily
monitor the network performance, detect the malfunctions and configure the network devices. In
the meantime, they can locate faults promptly and implement the fault diagnosis, capacity planning
and report generating.
SNMP Management Frame
SNMP management frame includes three network elements: SNMP Management Station, SNMP
Agent and MIB (Management Information Base).
SNM P M anage ment Station: SNMP Management Station is the workstation for running the
SNMP client program, providing a friendly management interface for the administrator to manage
the most network devices conveniently.
SNM P Agent: Agent is the server software operated on network devices with the responsibility of
receiving and processing the request packets from SNMP Management Station. In the meanwhile,
Agent will inform the SNMP Management Station of the events whenever the device status
changes or the device encounters any abnormalities such as device reboot.
MIB: MIB is the set of the managed objects. MIB defines a few attributes of the managed objects,
including the names, the access rights, and the data types. Every SNMP Agent has its own MIB.
The SNMP Management station can read/write the MIB objects based on its management right.
SNMP Management Station is the manager of SNMP network while SNMP Agent is the managed
object. The information between SNMP Management Station and SNMP Agent are exchanged
through SNMP (Simple Network Management Protocol). The relationship among SNMP
Management Station, SNMP Agent and MIB is illustrated in the following figure.
Figure 12-1 Relationship among SNMP Network Elements
SNM P Versions
This switch supports SNMP v3, and is compatible with SNMP v1 and SNMP v2c. The SNMP
versions adopted by SNMP Management Station and SNMP Agent should be the same.
Otherwise, SNMP Management Station and SNMP Agent cannot communicate with each other
normally. You can select the management mode with proper security level according to your actual
application requirement.
132
SNM P v1: SNMP v1 adopts Community Name authentication. The community name is used to
define the relation between SNMP Management Station and SNMP Agent. The SNMP packets
failing to pass community name authentication are discarded. The community name can limit
access to SNMP Agent from SNMP NMS, functioning as a password.
SNM P v2c: SNMP v2c also adopts community name authentication. It is compatible with SNMP
v1 while enlarges the function of SNMP v1.
SNM P v3: Based on SNMP v1 and SNMP v2c, SNMP v3 extremely enhances the security and
manageability. It adopts VACM (View-based Access Control Model) and USM (User-Based
Security Model) authentication. The user can configure the authentication and the encryption
functions. The authentication function is to limit the access of the illegal user by authenticating the
senders of packets. Meanwhile, the encryption function is used to encrypt the packets transmitted
between SNMP Management Station and SNMP Agent so as to prevent any information being
stolen. The multiple combinations of authentication function and encryption function can
guarantee a more reliable communication between SNMP Management station and SNMP Agent.
MIB Introduction
To uniquely identify the management objects of the device in SNMP messages, SNMP adopts the
hierarchical architecture to identify the managed objects. It is like a tree, and each tree node
represents a managed object, as shown in the following figure. Thus the object can be identified
with the unique path starting from the root and indicated by a string of numbers. The number string
is the Object Identifier of the managed object. In the following figure, the OID of the managed
object B is {1.2.1.1}. While the OID of the managed object A is {1.2.1.1.5}.
Figure 12-2 Architecture of the MIB tree
SNMP Configuration Outline
1. Create View
The SNMP View is created for the SNMP Management Station to manage MIB objects. The
managed object, uniquely identified by OID, can be set to under or out of the management of
SNMP Management Station by configuring its view type (included/excluded). The OID of managed
object can be found on the SNMP client program running on the SNMP Management Station.
2. Create SNMP Group
After creating the SNMP View, it’s required to create an SNMP Group. The Group Name, Security
Model and Security Level compose the identifier of the SNMP Group. The Groups with these three
items the same are considered to be the same. You can configure SNMP Group to control the
network access by providing the users in various groups with different management rights via the
Read View, Write View and Notify View.
133
3. Create SNMP User
The User configured in an SNMP Group can manage the switch via the client program on
management station. The specified User Name and the Auth/Privacy Password are used for
SNMP Management Station to access the SNMP Agent, functioning as the password.
SNMP module is used to configure the SNMP function of the switch, including three submenus:
SNM P Config, Notification and RM ON.
12.1 SNMP Config
The SNMP Config can be implemented on the Global Config, SNM P View, SNM P Group,
SNM P User and SNMP Community pages.
12.1.1 Global Config
To enable SNMP function, please configure the SNMP function globally on this page.
Choose the menu SNM P→SNM P Config→Global Config to load the following page.
Figure 12-3 Global Config
The following entries are displayed on this screen:
Global Config
SNM P:
Enable/Disable the SNMP function.
Local Engine
Local Engine ID:
Spec
ify the switch’s Engine ID for the remote clients. The
Engine ID is a unique alphanumeric string used to identify the
SNMP engine on the switch.
Remote Engine
Remote Engine ID:
Specify the Remote Engine ID for switch. The Engine ID is a
unique alphanumeri
c string used to identify the SNMP engine
on the remote device which receives traps and informs from
switch.
134
Note:
The amount of Engine ID characters must be even.
12.1.2 SNMP View
The OID (Object Identifier) of the SNMP packets is used to describe the managed objects of the
switch, and the MIB (Management Information Base) is the set of the OIDs. The SNMP View is
created for the SNMP management station to manage MIB objects.
Choose the menu SNM P→SNM P Config→SNM P Vie w to load the following page.
Figure 12-4 SNMP View
The following entries are displayed on this screen:
View Config
View Name:
Give a name to the View for identification. Each View can
include several entries with the same name.
MIB Object ID:
Enter the Object Identifier (OID) for the entry of View.
View Type:
Select the type for the view entry.
•
Include: The view entry can be managed by the SNMP
management station.
• Exclude: The view entry cannot
be managed by the SNMP
management station.
View Table
Selec
t:
Select the desired entry to delete the corresponding view. All
the entries of a View will be deleted together.
View Name:
Displays the name of the View entry.
View Type:
Displays the type of the View entry.
MIB Object ID:
Displays the OID of the View entry.
135
12.1.3 SNMP Group
On this page, you can configure SNMP Group to control the network access by providing the users
in various groups with different management rights via the Read View, Write View and Notify View.
Choose the menu SNM P→SNM P Config→SNM P Group to load the following page.
Figure 12-5 SNMP Group
The following entries are displayed on this screen:
Group Config
Group Name:
Enter the SNMP Group name. The Group Name, Security Model
and Security Level comp
ose the identifier of the SNMP Group.
The Groups with these three items the same are considered to be
the same.
Security Model:
Select the Security Model for the SNMP Group.
• v1:
SNMPv1 is defined for the group. In this model, the
Community Name is used f
or authentication. SNMP v1 can
be configured on the SNMP Community page directly.
• v2c:
SNMPv2c is defined for the group. In this model, the
Community Name is used for authentication. SNMP v2c can
be configured on the SNMP Community page directly.
• v3: SNMP
v3 is defined for the group. In this model, the USM
mechanism is used for authentication. If SNMPv3 is enabled,
the Security Level field is enabled for configuration.
Security Level:
Select the Security Level for the SNMP v3 Group.
• noAuthNoPriv: No authen
tication and no privacy security
level is used.
• authNoPriv: Only the authentication security level is used.
•
authPriv: Both the authentication and the privacy security
levels are used.
Read View:
Select the View to be the Read View. The management access is
restricted to read-
only, and changes cannot be made to the
assigned SNMP View.
Write View:
Select the View to be the Write View. The management access is
writing only and changes can be made to the assigned SNMP
136
View. The View defined both as the Read View and the Write View
can be read and modified.
Notify View:
Select the View to be the Notify View. The management station
can receive trap messages of the assigned SNMP view generated
by the switch's SNMP agent.
Group Table
Select:
Select the desired e
ntry to delete the corresponding group. It is
multi-optional.
Group Name:
Displays the Group Name here.
Security Model:
Displays the Security Model of the group.
Security Level:
Displays the Security Level of the group.
Read View:
Displays the Read View name in the entry.
Write View:
Displays the Write View name in the entry.
Notify View:
Displays the Notify View name in the entry.
Operation:
Click the Edit
button to modify the Views in the entry and click the
Modify button to apply.
Note:
Every Group should contain a Read View. The default Read View is viewDefault.
12.1.4 SNMP User
The User in an SNMP Group can manage the switch via the management station software. The
User and its Group have the same security level and access right. You can configure the SNMP
User on this page.
Choose the menu SNM P→SNM P Config→SNM P Use r to load the following page.
Figure 12-6 SNMP User
137
The following entries are displayed on this screen:
Use r Config
Use r Name:
Enter the User Name here.
User Type:
Select the type for the User.
•
Local User: Indicates that the user is connected to a
local SNMP engine.
•
Remote User: Indicates that the user is connected to a
remote SNMP engine.
Group Name:
Select the Group Name of the User. The User is classified to
the corresponding Group accor
ding to its Group Name,
Security Model and Security Level.
Security Model:
Select the Security Model for the User.
Security Level:
Select the Security Level for the SNMP v3 User.
Auth Mode:
Select the Authentication Mode for the SNMP v3 User.
• None: No authentication method is used.
• MD5:
The port authentication is performed via
HMAC-MD5 algorithm.
• SHA: The port authentication is performed via
SHA
(Secure Hash Algorithm)
. This authentication mode has
a higher security than MD5 mode.
Auth Password:
Enter the password for authentication.
Privacy Mode:
Select the Privacy Mode for the SNMP v3 User.
• None: No privacy method is used.
• DES: DES encryption method is used.
Privacy Password:
Enter the Privacy Password.
User Table
Select:
Select the desired entry
to delete the corresponding User. It is
multi-optional.
Use r Name:
Displays the name of the User.
User Type:
Displays the User Type.
Group Name:
Displays the Group Name of the User.
Security Model:
Displays the Security Model of the User.
Se curity Le
vel: Displays the Security Level of the User.
Auth Mode:
Displays the Authentication Mode of the User.
Privacy Mode:
Displays the Privacy Mode of the User.
Operation:
Click the Edit
button to modify the Group of the User and click
the Modify button to apply.
Note:
The SNMP User and its Group should have the same Security Model and Security Level.
138
12.1.5 SNMP Community
SNMP v1 and SNMP v2c adopt community name authentication. The community name can limit
access to the SNMP agent from SNMP network management station, functioning as a password. If
SNMP v1 or SNMP v2c is employed, you can directly configure the SNMP Community on this
page without configuring SNMP Group and User.
Choose the menu SNM P→SNM P Config→SNMP Community to load the following page.
Figure 12-7 SNMP Community
The following entries are displayed on this screen:
Community Config
Community Name :
Enter the Community Name here.
Access:
Defines the access rights of the community.
• re ad-only:
Management right of the Community is
restricted to read-only, and changes cannot be made to
the corresponding View.
• re ad-write:
Management right of the Community is
read-write and changes can be made to the corresponding
View.
MIB View:
Select the MIB View for the community to access.
Community Table
Select:
Select the desired entry to delete the corresponding Community. It
is multi-optional.
Community Name :
Displays the Community Name here.
Access:
Displays the right of the Community to access the View.
MIB View:
Displays the Views which the Community can access.
Operation:
Click the Edit
button to modify the MIB View and the Access right
of the Community, and then click the Modify button to apply.
Note :
The default MIB View of SNMP Community is viewDefault.
139
Configuration Procedure:
If SNMPv3 is employed, please take the following steps:
Step Operation Description
1 Enable SNM P function globally. Required. On the SNM P→SNMP Config
→Global
Config page, enable SNM P function globally.
2 Create SNMP View. Required. On the SNM P→SNMP Config→SNM P
View
page, create SNMP View of the management
agent. The default View Name is viewDefault and
the default OID is 1.
3 Create SNMP Group. Required. On the SNM P→SNMP Config→SNM P
Group
page, create SNMP Group for SNMPv3 and
specify SNMP Views with various access levels for
SNMP Group.
4 Create SNMP User. Required. On the SNM P→SNMP Config→SNM P
User page, create SNMP User in the Group and
configure the auth/privacy mode and auth/privacy
password for the User.
If SNMPv1 or SNMPv2c is employed, please take the following steps:
Ste p Operation Description
1 Enable SNMP function globally. Required. On the SNM P→SNM P
Config→Global Config page, enable SNM P
function globally.
2 Create SNMP View. Required. On the SNM P→SNM P Config→SNM P
View
page, create SNMP View of the
management agent. The default View Name is
viewDefault and the default OID is 1.
3
Configure
access level
for the User.
Create SNMP
Community
directly.
Required alternatively.
Create SNMP Community directly.
On the SNM P→SNMP Config→SNM P
Community
page, create SNMP Community
based on SNMP v1 and SNMP v2c.
Create SNMP Group and SNMP User.
Similar to the configuration way based on
SN
MPv3, you can create SNMP Group and
SNMP User of SNMP v1/v2c. The User
name can limit access to the SNMP agent
from SNMP network management station,
functioning as a community name. The
users can manage the device via the Read
View, Write View and Notify V
iew defined in
the SNMP Group.
Create SNMP
Group and SNMP
User.
140
12.2 Notification
With the Notification function enabled, the switch can initiatively report to the management station
about the important events that occur on the Views (e.g., the managed device is rebooted), which
allows the management station to monitor and process the events in time.
The notification information includes the following two types:
Tr a p ：Trap is the information that the managed device initiatively sends to the Network
management station without request.
Inform：Inform packet is sent to inform the management station and ask for the reply. The switch
will resend the inform request if it doesn’t get the response from the management station during
the Timeout interval, and it will terminate resending the inform request if the resending times reach
the specified Retry times. The Inform type, employed on SNMPv2c and SNMPv3, has a higher
security than the Trap type.
On this page, you can configure the notification function of SNMP.
Choose the menu SNM P→Notification→Notification to load the following page.
Figure 12-8 Notification Config
The following entries are displayed on this screen:
Create Notification
IP Address:
Enter the IP address of the management Host.
UDP Port:
Enter the number of the UDP port used to send notifications.
The UDP port functions with the IP address for the notification
sending. The default is 162.
Use r:
Enter the User name of the management station.
Security Model:
Select the Security Model of the management station.
Security Level:
Select the Security Level for the SNMP v3 User.
• noAuthNoPriv:
No authentication and no privacy security
level are used.
• authNoPriv: Only the authentication security level is used.
• authPriv: Both the a
uthentication and the privacy security
levels are used.
141
Typ e :
Select the type for the notifications.
• Trap: Indicates traps are sent.
• Inform:
Indicates informs are sent. The Inform type has a
higher security than the Trap type.
Re try:
Specify the amount o
f times the switch resends an inform
request. The switch will resend the inform request if it doesn’t
get the response from the management station during the
Time out
interval, and it will terminate resending the inform
request if the resending times reach the specified Retry times.
Timeout:
Specify the maximum time for the switch to wait for the
response from the management station before resending a
request.
Notification Table
Select:
Select the desired entry to delete the corresponding
management station.
IP Address: Displays the IP address of the management host.
UDP Port: Displays the UDP port used to send notifications.
Use r: Displays the User name of the management station.
Security Model: Displays the Security Model of the management station.
Security Level: Displays the Security Level for the SNMP v3 User.
Typ e : Displays the type of the notifications.
Timeout:
Displays the maximum time for the switch to wait for the
response from the management station before resending a
request.
Re try: Di
splays the amount of times the switch resends an inform
request.
Operation: Click the Edit
button to modify the corresponding entry and
click the Modify button to apply.
12.3 RMON
RMON (Remote Monitoring) based on SNMP (Simple Network Management Protocol)
architecture, functions to monitor the network. RMON is currently a commonly used network
management standard defined by Internet Engineering Task Force (IETF), which is mainly used to
monitor the data traffic across a network segment or even the entire network so as to enable the
network administrator to take the protection measures in time to avoid any network malfunction. In
addition, RMON MIB records network statistics information of network performance and
malfunction periodically, based on which the management station can monitor network at any time
effectively. RMON is helpful for network administrator to manage the large-scale network since it
reduces the communication traffic between management station and managed agent.
RMON Group
This switch supports the following four RMON Groups defined on the RMON standard (RFC1757):
History Group, Event Group, Statistic Group and Alarm Group.
142
RMON Group Function
History Group
After a history group is configured, the switch collects and records network
statistics
information periodically, based on which the management station
can monitor network effectively.
Event Group
Event Group is used to define RMON events. Alarms occur when an event is
detected.
Statistic Group Statistic Group is set to monitor the statisti
c of alarm variables on the specific
ports.
Alarm Group
Alarm Group is configured to monitor the specific alarm variables. When the
value of a monitored variable exceeds the threshold, an alarm event is
generated, which triggers the switch to act in the set way.
The RM ON Groups can be configured on the History Control, Event Config and Alarm Config
pages.
12.3.1 History Control
On this page, you can configure the History Group for RMON.
Choose the menu SNM P→RMON→History Control to load the following page.
Figure 12-9 History Control
The following entries are displayed on this screen:
History Control Table
Select:
Select the desired entry for configuration.
Index:
Displays the index number of the entry.
Port:
Specify the port from which the history samples were taken.
Interval:
Specify the interval to take samplings from the port.
Owner:
Enter the name of the device or user that defined the entry.
Status:
Select Enable/Disable the corresponding sampling entry.
143
12.3.2 Event Config
On this page, you can configure the RMON events.
Choose the menu SNM P→RMON→Event Config to load the following page.
Figure 12-10 Event Config
The following entries are displayed on this screen:
Event Table
Select:
Select the desired entry for configuration.
Index:
Displays the index number of the entry.
Use r:
Enter the name of the User or the community to which the
event belongs.
Description:
Give a description to the event for identification.
Typ e :
Select the event type, which determines the act way of the
network device in response to an event.
• None: No processing.
• Log: Logging the event.
• Notify: Sending trap messages to the management station.
• Log&Notify: Logging the event and sending trap messages
to the management station.
Owner:
Enter the name of the device or user that defined the entry.
Status:
Select Enable/Disable the corresponding event entry.
12.3.3 Alarm Config
On this page, you can configure Statistic Group and Alarm Group for RMON.
144
Choose the menu SNM P→RMON→Alarm Config to load the following page.
Figure 12-11 Alarm Config
The following entries are displayed on this screen:
Alarm Table
Select:
Select the desired entry for configuration.
Index:
Displays the index number of the entry.
Variable:
Select the alarm variables from the pull-down list.
Port:
Select the port on which the Alarm entry acts.
Sample Type:
Specify the sampling method for the selected variable and
comparing the value against the thresholds.
• Absolute:
Compares the values directly with the thresholds
at the end of the sampling interval.
• De lta:
Subtracts the last sampled value from the current
value. The difference in the values is compared to the
threshold.
Rising Threshold:
Enter the rising counter value that triggers the Rising Threshold
alarm.
Risin
g Event:
Select the index of the corresponding event which will be
triggered if the sampled value is larger than the Rising
Threshold.
Falling Threshold:
Enter the falling counter value that triggers the Falling Threshold
alarm.
Falling Event:
Select th
e index of the corresponding event which will be
triggered if the sampled value is lower than the Falling
Threshold.
Al a r m Typ e :
Specify the type of the alarm.
• All :
The alarm event will be triggered either the sampled
value exceeds the Rising Threshold or is under the Falling
Threshold.
• Rising:
When the sampled value exceeds the Rising
Threshold, an alarm event is triggered.
• Falling:
When the sampled value is under the Falling
Threshold, an alarm event is triggered.
145
Interval:
Enter the alarm interval time in seconds.
Owner:
Enter the name of the device or user that defined the entry.
Status:
Select Enable/Disable the corresponding alarm entry.
Note:
When alarm variables exceed the Threshold on the same direction continuously for several times,
an alarm event will only be generated on the first time, that is, the Rising Alarm and Falling Alarm
are triggered alternately for that the alarm following to Rising Alarm is certainly a Falling Alarm and
vice versa.
Return to CONTENTS
146
Chapter 13 LLDP
LLDP (Link Layer Discovery Protocol) is a Layer 2 protocol that is used for network devices to
advertise their own device information periodically to neighbors on the same IEEE 802 local area
network. The advertised information, including details such as device identification, capabilities
and configuration settings, is represented in TLV (Type/Length/Value) format according to the
IEEE 802.1ab standard, and these TLVs are encapsulated in LLDPDU (Link Layer Discovery
Protocol Data Unit). The LLDPDU distributed via LLDP is stored by its recipients in a standard MIB
(Management Information Base), making it possible for the information to be accessed by a
Network Management System (NMS) using a management protocol such as the Simple Network
Management Protocol (SNMP).
An IETF Standard MIB, as well as a number of vendor specific MIBs, have been created to
describe a network's physical topology and associated systems within that topology. However,
there is no standard protocol for populating these MIBs or communicating this information among
stations on the IEEE 802 LAN. LLDP protocol specifies a set. The device running LLDP can
automatically discover and learn about the neighbors, allowing for interoperability between the
network devices of different vendors. This protocol allows two systems running different network
layer protocols to learn about each other.
LLDP-MED (Link Layer Discovery Protocol for Media Endpoint Devices) is an extension of LLDP
intended for managing endpoint devices such as Voice over IP phones and network switches. The
LLDP-MED TLVs advertise information such as network policy, power via MD I, inventory
management, and device location details.
The LLDP and LLDP-MED information can be used by SNMP applications to simplify
troubleshooting, enhance network management, and maintain an accurate network topology.
LLDPDU Format
Each LLDPDU includes an ordered sequence of three mandatory TLVs followed by one or more
optional TLVs plus an End of LLDPDU TLV, as shown in the figure below. Chassis ID TLV, Port ID
TLV, TTL TLV and End TLV are the four mandatory TLVs for a LLDPDU. Optional TLVs provide
various details about the LLDP agent advertising them and they are selected by network
management.
The maximum length of the LLDPDU shall be the maximum information field length allowed by the
particular transmission rate and protocol. In IEEE 802.3 MACs, for example, the maximum
LLDPDU length is the maximum data field length for the basic, untagged MAC frame (1500
octets).
LLDP Working Mechanism
1) LLDP Admin Status
The transmission and the reception of LLDPDUs can be separately enabled for every port, making
it possible to configure an implementation to restrict the port either to transmit only or receive only,
or to allow the port to both transmit and receive LLDPDUs. Four LLDP admin statuses are
supported by each port.
147
Tx&Rx: the port can both transmit and receive LLDPDUs.
Rx_Only: the port can receive LLDPDUs only.
Tx_Only: the port can transmit LLDPDUs only.
Disable: the port cannot transmit or receive LLDPDUs.
2) LLDPDU transmission mechanism
If the ports are working in TxRx or Tx mode, they will advertise local information by
sending LLDPDUs periodically.
If there is a change in the local device, the change notification will be advertised. To
prevent a series of successive LLDPDUs transmissions during a short period due to
frequent changes in local device, a transmission delay timer is set by network
management to ensure that there is a defined minimum time between successive LLDP
frame transmissions.
If the LLDP admin status of the port is changed from Disable/Rx to TxRx/Tx, the Fast
Start Mechanism will be active, the transmit interval turns to be 1 second, several
LLDPDUs will be sent out, and then the transmit interval comes back to the regular
interval.
3) LLDPDU receipt mechanism
When a port is working in TxRx or Rx mode, the device will check the validity of the received
LLDPDUs and the attached TLVs, save this neighbor information to the local device and then set
the aging time of this information according to the TTL value of TTL (Time To Live) TLV. Once the
TTL is 0, this neighbor information will be aged out immediately.
The aging time of the local information in the neighbor device is determined by TTL. Hold
Multiplier is a multiplier on the Transmit Interval that determines the actual TTL value used in an
LLDPDU. TTL = Hold Multiplier * Transmit Interval.
TLV
TLV refers to Type/Length/Value and is contained in a LLDPDU. Type identifies what kind of
information is being sent, Length indicates the length of information string in octets and Value is
the actual information to be sent. The basic TLV Format is shown as follows:
Each TLV is identified by a unique TLV type value that indicates the particular kind of information
contained in the TLV.
148
The following table shows the details about the currently defined TLVs.
TLV t yp e TLV Na me Description Usage in
LLDPDU
0 End of LLDPDU
Mark the end of the TLV sequence in LLDPDUs.
Any information following an End Of LLDPDU
TLV shall be ignored.
Mandatory
1 Chassis ID Identifies the Chassis
address of the connected
device.
Mandatory
2 Port ID
Identifies the specific port that transmitted the
LLDP frame. When the device does not advertise
MED TLV, this field displays the port name of the
port; when the de
vice advertises MED TLV, this
field displays the MAC address of the port.
Mandatory
3 Time To Live
Indicates the number of seconds that the
neighbor device is to regard the local information
to be valid.
Mandatory
4 Port Description Identifies the description string of the port. Optional
5 System Name Identifies the system name. Optional
6 System
Description
Identifies the system description. Optional
7 System
Capabilities
Identifies the main functions of the system and
the functions enabled.
Optional
8 Management
Address
Identifies the management IP address, the
corresponding interface number and OID (Object
Identifier). The management IP address is
specified by the user.
Optional
127 Organizationally
Specific
Allows different organizations, such a
s IEEE
802.1, IEEE 802.3, IETF, as well as individual
software and equipment vendors, to define TLVs
that advertise information to remote device.
Optional
Optional TLVs are grouped into two categories including basic management TLV and
Organizationally-specific TLV.
1) Basic Management TLV
A set of TLVs considered to be basic to the management of the network stations are required for
all LLDP implementations.
2) Organizationally Specific TLV
Different organizations have defined various TLVs. For instance, Port VLAN ID TLV, Port and
Protocol VLAN ID TLV, VLAN Name TLV And Protocol Identity TLV are defined by IEEE 802.1,
while MAC/PHY Configuration/Status TLV, Power Via MDI TLV, Link Aggregation TLV and
Maximum Frame TLV are defined by IEEE 802.3. Some specific TLVs are for LLDP-MED protocol,
such as LLDP-MED Capabilities TLV, Network Policy TLV, Extended Power-via-MDI TLV,
Hardware Revision TLV and so on.
149
Note:
For detailed introduction of TLV, please refer to IEEE 802.1AB standard and ANSI/TIA-1057.
In TP-LINK switch, the following LLDP optional TLVs are supported.
TLV Type Description
Port Description TLV
The Port Description TLV allows network management to
advertise the IEEE 802 LAN station's port description.
System Capabilities TLV The System Capabilities
TLV identifies the primary functions of
the system and whether or not these primary functions are
enabled.
System Description TLV T
he System Description TLV allows network management to
advertise the system's description, which should include the full
na
me and version identification of the system's hardware type,
software operating system, and networking software.
Syste m Name TLV
The System Name TLV allows network management to
advertise the system's assigned name, which should be the
system's fully qualified domain name.
Management Address TLV
The Management Address TLV identifies an address associated
with the local LLDP agent that may be used to reach higher
entities to assist discovery by network management.
Port VLAN ID TLV The Port VLAN ID TLV all
ows a VLAN bridge port to advertise
the port's VLAN identifier (PVID) that will be associated with
untagged or priority tagged frames.
Port And Protocol VLAN ID
TLV
The Port And Protocol VLAN ID TLV allows a bridge port to
advertise a port and protocol VLAN ID.
VLAN Name TLV The VLAN Name TLV allows an IEEE 802.1Q-
compatible IEEE
802 LAN station to advertise the assigned name of any VLAN
with which it is configured.
Link Aggregation TLV
The Link Aggregation TLV indicates whether the link is capable
of be
ing aggregated, whether the link is currently in an
aggregation, and if in an aggregation, the port identification of
the aggregation.
MAC/PHY
Configuration/Status TLV
The MAC/PHY Configuration/Status TLV identifies: a)The duplex
and bit-rate capability o
f the sending IEEE 802.3 LAN node that
is connected to the physical medium; b)The current duplex and
bit-
rate settings of the sending IEEE 802.3 LAN node; c)Whether
these settings are the result of auto-
negotiation during link
initiation or of manual set override action.
Max Frame Size TLV
The Maximum Frame Size TLV indicates the maximum frame
size capability of the implemented MAC and PHY.
Power Via MDI TLV
The Power Via MDI TLV allows network management to
advertise and discover the MDI power support ca
pabilities of the
sending IEEE 802.3 LAN station.
150
The LLDP module is mainly for LLDP function configuration of the switch, including three
submenus: Basic Config, Device Info, Device Statistics and LLDP-M ED.
13.1 Basic Config
LLDP is configured on the Global Config and Port Config pages.
13.1.1 Global Config
On this page you can configure the LLDP parameters of the device globally.
Choose the menu LLDP→Basic Config→Global Config to load the following page.
Figure 13-1 LLDP Global Configuration
The following entries are displayed on this screen:
Global Config
LLDP: Enable/disable LLDP function globally.
Parameters Config
Transmit Interval:
Enter the interval for the local device to transmit LLDPDU to its
neighbors. The default value is 30.
Hold Multiplier:
Enter a multiplier on the Transmit Interval. It determines the actual
TTL (Time To Live) value use
d in an LLDPDU. TTL = Hold
Multiplier * Transmit Interval. The default value is 4.
Transmit Delay: Enter a value from 1 to 8192 in seconds
to specify the time for the
local device to transmit LLDPDU to its neighbors after changes
occur so as to prevent LLDPDU being sent frequently.
The default
value is 2.
Reinit Delay: This parameter indicates the amount of delay from when LLDP
status becomes "disable" until re-
initialization will be attempted.
The default value is 3.
Notification Interval:
Specify the i
nterval of Trap message which will be sent from local
device to network management system. The default value is 5.
151
Fast Start Time s:
When the port's LLDP state transforms from Disable (or Rx_Only)
to Tx&Rx (or Tx_Only), the fast start mechanism will be en
abled,
that is, the transmit interval will be shorten to a second, and
several LLDPDUs will be sent out (the number of LLDPDUs
equals this parameter). The default value is 3.
13.1.2 Port Config
On this page you can configure all ports' LLDP parameters.
Choose the menu LLDP→Basic Config→Port Config to load the following page.
Figure 13-2 LLDP Port Config
The following entries are displayed on this screen:
LLDP Port Config
Port Sele ct: Select the desired port to configure.
Admin Status: Select the port’s LLDP operating mode:
Tx&Rx: send and receive LLDP frames.
Rx_Only: Only receive LLDP frames.
Tx_Only: Only send LLDP frames.
Disable: neither send nor receive LLDP frames.
Notification Mode: Allows you to enable or disable
the ports' SNMP notification. If
enabled, the local device will notify the trap event to SNMP server.
Included TLVs: Select TLVs to be included in outgoing LLDPDU.
Details: Click the Detail button
to display the included TLVs and select the
desired TLVs.
152
13.2 Device Info
You can view the LLDP information of the local device and its neighbors on the Local Info and
Neighbor Info pages respectively.
13.2.1 Local Info
On this page you can see all ports' configuration and system information.
Choose the menu LLDP→Device Info→Local Info to load the following page.
Figure 13-3 LLDP Local Information
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh: Enable/Disable the auto refresh function.
153
Refresh Rate: Specify the auto refresh rate.
Local Info
Enter the desired port number and click Select to display the information of the corresponding
port.
13.2.2 Neighbor Info
On this page you can get the information of the neighbors.
Choose the menu LLDP→Device Info→Neighbor Info to load the following page.
Figure 13-4 LLDP Neighbor Information
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh: Enable/Disable the auto refresh function.
Refresh Rate: Specify the auto refresh rate.
Neighbor Info
Port Sele ct: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Local Port: Displays the local port number connecting to the neighbor device.
Syste m Name : Displays the system name of the neighbor device.
Chassis ID: Displays the Chassis ID of the neighbor device.
System Description:
Displays the system description of the neighbor device.
Neighbor Port: Displays the port number of the neighbor linking to local port.
Information:
Click Information to display the detailed information of the
neighbor device.
13.3 Device Statistics
You can view the LLDP statistics of the local device through this feature.
154
Choose the menu LLDP→Device Statistics→Statistic Info to load the following page.
Figure 13-5 LLDP Statistic Information
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh: Enable/Disable the auto refresh function.
Refresh Rate: Specify the auto refresh rate.
Global Statistics
Last Update: Displays latest update time of the statistics.
Total Inserts: Displays the number of neighbors inserted till last update time.
Total Deletes: Displays the number of neighbors deleted by local device.
Total Drops: Displays the number of neighbors dropped by local device.
Total Ageouts: Displays the number of overtime neighbors in local device.
155
Neighbor Statistics
Port Sele ct: Click the Select button to quick-select the corresponding port
based on the port number you entered.
Port: Displays local device's port number.
Transmit Total: Displays the number of LLDPDUs sent by this port.
Receive Total: Displays the number of LLDPDUs received by this port.
Discards: Displays the number of LLDPDUs discarded by this port.
Errors: Displays the number of error LLDPDUs received by this port.
Ageouts: Displays the number of overtime neighbors linking to this port.
TLV Discards: Displays the number of TLVs dropped by this port.
TLV Unknowns: Displays the number of unknown TLVs received by this port.
13.4 LLDP-MED
LLDP-MED is an extension of LLDP intended for managing endpoint devices such as Voice over
IP phones and network switches. The LLDP-MED TLVs advertise information such as network
policy, power via MDI, inventory management, and device location details.
Elements
LLDP-M ED Device: Refers to any device which implements this Standard.
LLDP-M ED Dev ice Type : LLDP-MED devices are comprised of two primary device types:
Network Connectivity Devices and Endpoint Devices.
Network Connectivity Device: Refers to an LLDP-MED Device that provides access to the IEEE
802 based LAN infrastructure for LLDP-MED Endpoint Devices. Bridge is a Network Connectivity
Device.
Endpoint Device: Refers to an LLDP-MED Device at the network edge, providing some aspects
of IP communications service, based on IEEE 802 LAN technology. Endpoint Devices may be a
member of any of the Endpoint Device Classes. Endpoint Devices are composed of three defined
Classes: Class I, Class II and Class III.
Generic Endpoint Device (Class I): The most basic class of Endpoint Device.
Media Endpoint Device (Class II): The class of Endpoint Device that supports media stream
capabilities.
Communication Device Endpoint (Class III): The class of Endpoint Device that directly supports
end users of the IP communication system.
TLV Description
Network Policy TLV
The Network Policy TLV allows both Network Connectivity
Devices and Endpoints to advertise VLAN configuration and
associated Layer 2
and Layer 3 attributes that apply for a set
of specific applications on that port.
156
TLV Description
Location Identification TLV
The Location Identification TLV provides for advertisement of
location identifier information to Communication Endpoint
Devices, based on config
uration of the Network Connectivity
Device it's connected to. You can set the Location
Identification content in Location Identification Parameters. If
Location Identification TLV is included and Location
Identification Parameters isn't set, a default valu
e is used in
Location Identification TLV.
Extended Power-Via-MDI TLV The Extended Power-Via-
MDI TLV is intended to enable
advanced power management between LLDP-
MED Endpoint
and Network Connectivity Devices, and it allows
advertisement of fine grained pow
er requirement details,
Endpoint power priority, as well as both Endpoint and Network
Connectivity Device power status.
Inventory TLV
The Inventory TLV set contains seven basic Inventory
management TLVs, that is,
Hardware Revision TLV, Firmware
Revision T
LV, Software Revision TLV, Serial Number TLV,
Manufacturer Name TLV, Model Name TLV and Asset ID
TLV. If support for any of the TLVs in the Inventory
Management set is implemented, then support for all
Inventory Management TLVs shall be implemented.
LLDP-MED is configured on the Global Config, Port Config, Local Info and Ne ighbor Info
pages.
13.4.1 Global Config
On this page you can configure the LLDP-MED parameters of the device globally.
Choose the menu LLDP→LLDP-M ED→Global Config to load the following page.
Figure 13-6 LLDP-MED Global Configuration
The following entries are displayed on this screen:
LLDP-MED Parameters Config
Fast Start Count: When LLDP-
MED fast start mechanism is activated, multiple
LLDP-MED frames will be transmitted based on this parameter.
Device Class: LLDP-
MED devices are comprised of two primary device types:
Network Connectivity Devices and Endpoint Devices. In turn,
Endpoint Devices are composed of three defined Classes: Class I,
Class II and Class III. Bridge is a Network Connectivity Device.
157
13.4.2 Port Config
On this page you can configure all ports' LLDP-MED parameters.
Choose the menu LLDP→LLDP-M ED→Port Config to load the following page.
Figure 13-7 LLDP-MED Port Configuration
The following entries are displayed on this screen:
LLDP-MED Port Config
Port Sele ct: Select the desired port to configure.
LLDP-M ED Status: Configure the port's LLDP-MED status:
Enable: Enable the port's LLDP-MED s
tatus, and the port's Admin
Status will be changed to Tx&Rx.
Disable: Disable the port's LLDP-MED status.
Included TLVs: Select TLVs to be included in outgoing LLDPDU.
Detail: Click the Detail button
to display the included TLVs and select the
desired TLVs.
158
Included TLVs
Select TLVs to be included in outgoing LLDPDU.
Location Identification Parameters
Configure the Location Identification TLV's content in outgoing LLDPDU of the port.
Emergency
Number:
Emergency number is Emergency Call Service ELIN id
entifier,
which is used during emergency call setup to a traditional CAMA
or ISDN trunk-based PSAP.
Civic Address: The Civic address is defined to reuse the relevant sub-
fields of the
DHCP option for Civic Address based Location Configuration
Information as specified by IETF.
13.4.3 Local Info
On this page you can see all ports' LLDP-MED configuration.
159
Choose the menu LLDP→LLDP-M ED→Local Info to load the following page.
Figure 13-8 LLDP-MED Local Information
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh: Enable/Disable the auto refresh function.
Refresh Rate: Specify the auto refresh rate.
Local Info
Enter the desired port number and click Select to display the information of the corresponding
port.
13.4.4 Neighbor Info
On this page you can get the LLDP-MED information of the neighbors.
160
Choose the menu LLDP→LLDP-M ED→Neighbor Info to load the following page.
Figure 13-9 LLDP-MED Neighbor Information
The following entries are displayed on this screen:
Auto Refresh
Auto Refresh: Enable/Disable the auto refresh function.
Refresh Rate: Specify the auto refresh rate.
Neighbor Info
Port Sele ct: Click the Select button to quick-
select the corresponding port
based on the port number you entered.
Local Port: Displays the local port number connecting to the neighbor device.
Device Type: Displays the device type of the neighbor.
Application Type: Displays the application type of the neighbor.
Application Type
indicates the primary function of the applications defined for the
network policy.
Local Data Format: Displays the location identification of the neighbor.
Power Type:
Displays the power type of the neighbor device, Power Sourcing
Entity (PSE) or Powered Device (PD).
Information: Click the Information
button to display the detailed information of
the corresponding neighbor.
Return to CONTENTS
161
Chapter 14 Maintenance
Maintenance module, assembling the commonly used system tools to manage the switch,
provides the convenient method to locate and solve the network problem.
(1) System Monitor: Monitor the utilization status of the memory and the CPU of switch.
(2) Log: View the configuration parameters of the switch and find out the errors via the Logs.
(3) Device Diagnostics: Test the connection status of the cable connected to the switch.
(4) Net work Diagnostics: Test whether the destination device is reachable and detect the
route hops from the switch to the destination device.
14.1 System Monitor
System Monitor functions to display the utilization status of the memory and the CPU of switch via
the data graph. The CPU utilization rate and the memory utilization rate should fluctuate stably
around a specific value. If the CPU utilization rate or the memory utilization rate increases
markedly, please detect whether the network is being attacked.
The System Monitor function is implemented on the CPU Monitor and Memory M onitor pages.
14.1.1 CPU Monitor
Choose the menu Maintenance→System Monitor→CPU Monitor to load the following page.
Figure 14-1 CPU Monitor
Click the Monitor button to enable the switch to monitor and display its CPU utilization rate every
four seconds.
162
14.1.2 Memory Monitor
Choose the menu Mainte nance→System Monitor→Me mory M onitor to load the following page.
Figure 14-2 Memory Monitor
Click the Monitor button to enable the switch to monitor and display its Memory utilization rate
every four seconds.
14.2 Log
The Log system of switch can record, classify and manage the system information effectively,
providing powerful support for network administrator to monitor network operation and diagnose
malfunction.
The Logs of switch are classified into the following eight levels.
Severity Level Description
emergencies 0 The system is unusable.
alerts 1 Action must be taken immediately.
critical 2 Critical conditions
errors 3 Error conditions
warnings 4 Warnings conditions
notifications 5 Normal but significant conditions
informational 6 Informational messages
debugging 7 Debug-level messages
Table 14-1 Log Level
163
The Log function is implemented on the Log Table , Local Log, Re mote Log and Backup Log
pages.
14.2.1 Log Table
The switch supports logs output to two directions, namely, log buffer and log file. The information
in log buffer will be lost after the switch is rebooted or powered off whereas the information in log
file will be kept effective even the switch is rebooted or powered off. Log Table displays the system
log information in log buffer.
Choose the menu Maintenance→Log→Log Table to load the following page.
Figure 14-3 Log Table
The following entries are displayed on this screen:
Log Info
Index
: Displays the index of the log information.
Time
: Displays the time when the l
og event occurs. The log can get the
correct time after you configure on the System ->System
Info->System Time Web management page.
Module
:
Displays the module which the log information belongs to. You can
select a module from the drop-down list to displa
y the corresponding
log information.
Severity
:
Displays the severity level of the log information. You can select a
severity level to display the log information whose severity level value
is the same or smaller.
Content
: Displays the content of the log information.
Note:
1. The logs are classified into eight levels based on severity. The higher the information severity
is, the lower the corresponding level is.
2. This page displays logs in the log buffer, and at most 512 logs are displayed.
14.2.2 Local Log
Local Log is the log information saved in switch. By default, all system logs with severities from
level_0 to level_6 are saved in log buffer. On this page, you can set the output channel for logs.
164
Choose the menu Maintenance→Log→Local Log to load the following page.
Figure 14-4 Local Log
The following entries are displayed on this screen:
Local Log Config
Select
:
Select the desired entry to configure the corresponding local log.
L
og Buffer:
Indicates the RAM for saving system log. The inforamtion in the
log buffer is displayed on the Log Table page. It will be lost when
the switch is restarted.
Log File
:
Indicates the flash sector for saving system log. The inforamtion
in the log
file will not be lost after the switch is restarted and can
be exported on the Backup Log page.
Severity
:
Specify the severity level of the log information output to each
channel. Only the log with the same or smaller severity level
value will be output.
Status
: Enable/Disable the channel.
14.2.3 Remote Log
Remote log feature enables the switch to send system logs to the Log Server. Log Server is to
centralize the system logs from various devices for the administrator to monitor and manage the
whole network.
165
Choose the menu Maintenance→Log→Remote Log to load the following page.
Figure 14-5 Log Host
The following entries are displayed on this screen:
Log Host
Index
:
Displays the index of the log host. The switch supports 4 log
hosts.
Host IP
: Configure the IP for the log host.
UDP Port
:
Displays the UDP port used for receiving/sending log
information. Here we use the standard port 514.
Severity
:
Specify the severity level of the log information sent to each log
host. Only the log with the sa
me or smaller severity level value
will be sent to the corresponding log host.
Status
: Enable/Disable the log host.
Note:
The Log Server software is not provided. If necessary, please download it on the Internet.
14.2.4 Backup Log
Backup Log feature enables the system logs saved in the switch to be output as a file for device
diagnosis and statistics analysis. When a critical error results in the breakdown of the system, you
can export the logs to get some related important information about the error for device diagnosis
after the switch is restarted.
Choose the menu Maintenance→Log→Backup Log to load the following page.
Figure 14-6 Backup Log
166
The following entry is displayed on this screen:
Backup Log
Backup Log
: Click the Backup Log button to save the log as a file to your computer.
Note:
It will take a few minutes to backup the log file. Please wait without any operation.
14.3 Device Diagnostics
This switch provides Cable Test function for device diagnostics.
14.3.1 Cable Test
Cable Test functions to test the connection status of the cable connected to the switch, which
facilitates you to locate and diagnose the trouble spot of the network.
Choose the menu Maintenance→Device Diagnostics→Cable Test to load the following page.
Figure 14-7 Cable Test
The following entries are displayed on this screen:
Cable Test
Port
: Select the port for cable testing.
Pair
: Displays the Pair number.
Status
:
Displays the connection status of the cable connected to the port. The
test results of the cable include normal, close, open or impedance.
Length
:
If the connection status is normal, here displays the length range of
the cable.
Error
: I
f the connection status is close, open or impedance, here displays the
error length of the cable.
Note:
1. The interval between two cable tests for one port must be more than 3 seconds.
2. The result is more reasonable when the cable pair is in the open status.
167
3. The test result is just for your reference.
4. If the port is 100Mbps and its connection status is normal, cable test can’t get the length of the
cable.
14.4 Network Diagnostics
This switch provides Ping test and Tracert test functions for network diagnostics.
14.4.1 Ping
Ping test function, testing the connectivity between the switch and one node of the network,
facilitates you to test the network connectivity and reachability of the host so as to locate the
network malfunctions.
Choose the menu Maintenance→Network Diagnostics→Ping to load the following page.
Figure 14-9 Ping
The following entries are displayed on this screen:
Ping Config
Destination IP
: Enter the IP address of the destination node for Ping test.
Ping Times
:
Enter the amount of times to send test data during Ping testing. The
default value is recommended.
Data Size
:
Enter the size of the sending data during Ping testing. The default
value is recommended.
Interval
: Specify the interval to send IC
MP request packets. The default value
is recommended.
168
14.4.2 Tracert
Tracert test function is used to test the connectivity of the gateways during its journey from the
source to destination of the test data. When malfunctions occur to the network, you can locate
trouble spot of the network with this tracert test.
Choose the menu Maintenance→Network Diagnostics→Tracert to load the following page.
Figure 14-10 Tracert
The following entries are displayed on this screen:
Tracert Config
Destination IP
: Enter the IP address of the destination device.
Max Hop
:
Specify the maximum number of the route hops the test data can pass
through.
Return to CONTENTS
169
Appendix A: Specifications
Standards
IEEE802.3 10Base-T Ethernet
IEEE802.3u 100Base-TX/100Base-FX Fast Ethernet
IEEE802.3ab 1000Base-T Gigabit Ethernet
IEEE802.3z 1000Base-X Gigabit Ethernet
IEEE802.3x Flow Control
IEEE802.1p QoS
IEEE802.1q VLAN
IEEE802.1d Spanning Tree
IEEE802.1s Multiple Spanning Tree
IEEE802.1w Rapid Spanning Tree Protocol
Transmission Rate
Ethernet: 10Mbps HD，20Mbps FD
Fast Ethernet: 100Mbps HD，200Mbps FD
Gigabit Ethernet: 2000Mbps FD
Transmission Medium
10Base-T: UTP/STP of Cat. 3 or above
100Base-TX: UTP/STP of Cat. 5 or above
100Base-FX: MMF or SMF SFP Module (Optional)
1000Base-T: 4-pair UTP (≤100m) of Cat. 5e or above
1000Base-X: MMF or SMF SFP Module (Optional)
LED PWR, SYS, PoE MAX, FAN, 10/100M or PoE, 1000M
LEDs, 1000Mbps LEDs
Transmission Method Store and Forward
Packets Forwarding Rate
10BASE-T：14881pps/port
100BASE-TX：148810pps/port
1000Base-T：1488095pps/port
Operating
Environment
Operating Temperature: 0
℃
~ 40
℃
Storage Temperature: -40
℃
~ 70
℃
Operating Humidity: 10% ~ 90% RH Non-condensing
Storage Humidity: 5% ~ 90% RH Non-condensing
Return to CONTENTS
170
Appendix B: Configuring the PCs
In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows 7. First
make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary.
Configure TCP/IP component
1) On the Windows taskbar, click the Start button, and then click Control Panel.
2) Click the Network and Internet icon, and then click on the Ne twork and Sharing
Center tab in the appearing window.
3) Click Change adapter settings on the left pane.
Figure B-0-1
171
4) Double click the Local Network icon in the prompt window.
5) Double click on the Internet Protocol Ve r s ion 4 (TCP/IPv4) in the Local Network
Properties window.
Figure B-0-2
172
6) The following Interne t Protocol Version 4 (TCP/IPv4) Prope rtie s window will display
and the General tab is open on this window by default.
Figure B-0-3
7) Select Use the following IP address. And the following items will be available. If the switch's
IP address is 192.168.0.1, specify IP address as 192.168.0.x (x is from 2 to 254), and the
Subnet mask as 255.255.255.0.
Now:
Click OK to save your settings.
Return to CONTENTS
173
Appendix C: Glossary
Boot Protocol (BOOTP)
BOOTP is used to provide bootup information for network devices, including IP address
information, the address of the TFTP server that contains the devices system files, and the name
of the boot file.
Class of Service (CoS)
CoS is supported by prioritizing packets based on the required level of service, and then placing
them in the appropriate output queue. Data is transmitted from the queues using weighted
round-robin service to enforce priority service and prevent blockage of lower-level queues. Priority
may be set according to the port default, the packet’s priority bit (in the VLAN tag), TCP/UDP port
number, or DSCP priority bit.
Differentiated Services Code Point (DSCP)
DSCP uses a six-bit tag to provide for up to 64 different forwarding behaviors. Based on network
policies, different kinds of traffic can be marked for different kinds of forwarding. The DSCP bits
are mapped to the Class of Service categories, and then into the output queues.
Domain Name Service (DNS)
A system used for translating host names for network nodes into IP addresses.
Dynamic Host Control Protocol (DHCP)
Provides a framework for passing configuration information to hosts on a TCP/IP network. DHCP
is based on the Bootstrap Protocol (BOOTP), adding the capability of automatic allocation of
reusable network addresses and additional configuration options..
IEEE 802.1D
Specifies a general method for the operation of MAC bridges, including the Spanning Tree
Protocol.
IEEE 802.1Q
VLAN Tagging—Defines Ethernet frame tags which carry VLAN information. It allows switches to
assign endstations to different virtual LANs, and defines a standard way for VLANs to
communicate across switched networks.
IEEE 802.1p
An IEEE standard for providing quality of service (QoS) in Ethernet networks. The standard uses
packet tags that define up to eight traffic classes and allows switches to transmit packets based on
the tagged priority value.
IEEE 802.3ac
Defines frame extensions for VLAN tagging.
IEEE 802.3x
Defines Ethernet frame start/stop requests and timers used for flow control on full-duplex links.
(Now incorporated in IEEE 802.3-2002)
174
Internet Group Management Protocol (IGMP)
A protocol through which hosts can register with their local router for multicast services. If there is
more than one multicast switch/router on a given subnetwork, one of the devices is made the
“querier” and assumes responsibility for keeping track of group membership.
IGMP Snooping
Listening to IGMP Query and IGMP Report packets transferred between IP Multicast routers and
IP Multicast host groups to identify IP Multicast group members.
IGMP Query
On each subnetwork, one IGMP-capable device will act as the querier — that is, the device that
asks all hosts to report on the IP multicast groups they wish to join or to which they already belong.
The elected querier will be the device with the lowest IP address in the subnetwork.
IP Multicast Filtering
It is a feature to allow or deny the Client to add the specified multicast group.
Multicast Switching
A process whereby the switch filters incoming multicast frames for services forwhich no attached
host has registered, or forwards them to all ports contained within the designated multicast group.
Laye r 2
Data Link layer in the ISO 7-Layer Data Communications Protocol. This is related directly to the
hardware interface for network devices and passes on traffic based on MAC addresses.
Link Aggregation
See Port Trunk.
Management Information Base (MIB)
An acronym for Management Information Base. It is a set of database objects that contains
information about a specific device.
MD5 Message-Digest Algorithm
An algorithm that is used to create digital signatures. It is intended for use with 32 bit machines
and is safer than the MD4 algorithm, which has been broken. MD5 is a one-way hash function,
meaning that it takes a message and converts it into a fixed string of digits, also called a message
digest.
Network Time Protocol (NTP)
NTP provides the mechanisms to synchronize time across the network. The time servers operate
in a hierarchical-master-slave configuration in order to synchronize local clocks within the subnet
and to national time standards via wire or radio.
Port Mirroring
A method whereby data on a target port is mirrored to a monitor port for troubleshooting with a
logic analyzer or RMON probe. This allows data on the target port to be studied unobstructively.
Port Trunk
Defines a network link aggregation and trunking method which specifies how to create a single
high-speed logical link that combines several lower-speed physical links.
175
Remote Authentication Dial-in User Service (RADIUS)
RADIUS is a logon authentication protocol that uses software running on a central server to
control access to RADIUS-compliant devices on the network.
Remote Monitoring (RMON)
RMON provides comprehensive network monitoring capabilities. It eliminates the polling required
in standard SNMP, and can set alarms on a variety of traffic conditions, including specific error
types.
Rapid Spanning Tree Protocol (RSTP)
RSTP reduces the convergence time for network topology changes to about 10% of that required
by the older IEEE 802.1D STP standard.
Simple Network Management Protocol (SNMP)
The application protocol in the Internet suite of protocols which offers network management
services.
Simple Network Time Protocol (SNTP)
SNTP allows a device to set its internal clock based on periodic updates from a Network Time
Protocol (NTP) server. Updates can be requested from a specific NTP server, or can be received
via broadcasts sent by NTP servers.
Spanning Tree Algorithm (STA)
A technology that checks your network for any loops. A loop can often occur in complicated or
backup linked network systems. Spanning Tree detects and directs data along the shortest
available path, maximizing the performance and efficiency of the network.
Telnet
Defines a remote communication facility for interfacing to a terminal device over TCP/IP.
Transmission Control Protocol/Internet Protocol (TCP/IP)
Protocol suite that includes TCP as the primary transport protocol, and IP as the network layer
protocol.
Trivial File Transfer Protocol (TFTP)
A TCP/IP protocol commonly used for software downloads.
User Datagram Protocol (UDP)
UDP provides a datagram mode for packet-switched communications. It uses IP as the underlying
transport mechanism to provide access to IP-like services. UDP packets are delivered just like IP
packets – connection-less datagrams that may be discarded before reaching their targets. UDP is
useful when TCP would be too complex, too slow, or just unnecessary.
Vir t u al LAN (VLAN)
A Virtual LAN is a collection of network nodes that share the same collision domain regardless of
their physical location or connection point in the network. A VLAN serves as a logical workgroup
with no physical barriers, and allows users to share information and resources as though located
on the same LAN.
Return to CONTENTS