TP-Link TL-ANT2424MD User Manual
Displayed below is the user manual for TL-ANT2424MD by TP-Link which is a product in the Network Antennas category. This manual has pages.
Installation Guide
2x2 MIMO Dish Antenna
Model: TL-ANT2424MD & TL-ANT5830MD
CONTENTS
Introduction
Specifications
Safety Notice
Package Contents
Installation Requirements
Hardware Overview
Hardware Installation
1
1
2
2
3
3
4
1
Introduction
The TL-ANT2424MD, 2.4GHz 15dBi 2x2 MIMO Dish Antenna, can be used
with the outdoor wireless Base Station WBS210 to achieve a stable
long-distance point-to-point signal transmission.
The TL-ANT5830MD, 5GHz 19dBi 2x2 MIMO Dish Antenna, can be used
with the outdoor wireless Base Station WBS510 to achieve a stable
long-distance point-to-point signal transmission.
Specifications
Electrical Specifications TL-ANT2424MD TL-ANT5830MD
Frequency Range
Gain
VSWR
HPOL Beamwidth (3 dB)
VPOL Beamwidth (3 dB)
Elevation Beamwidth (3 dB)
F/B Ratio
Polarization
Impedance
Connector
2.3~2.7 GHz
24 dBi
1.8 Max
6°
6°
6°
32 dB Min
Horizontal & Vertical
50 Ω
RP-SMA
5.0 - 6.0 GHz
30 dBi
1.8 Max
6°
6°
6°
34 dB Min
Horizontal & Vertical
50 Ω
RP-SMA
Antenna Dimension
Weight
Rated Wind Velocity
Mounting
Φ 600 mm
6.0 Kg
241 Km/h
Pole Mount
Mechanical Specifications
2
Package Contents
Heed all warnings:
Mount the antenna at a safe location, far away from power lines,
lamp posts, and other electrical cables.
Do not mount the antenna in the rain or thunderstorm.
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
For your own safety, please seek a qualified service technician for
assistance.
Safety Notice
Antenna FeedDish Reector Antenna Mount Bracket
Installation Guide
Installation Guide
2x2 MIMO Dish Antenna
Model: TL-ANT2424MD & TL-ANT5830MD
M4 Bolts
(Qty. 4)
Pole-mount Clamps
(Qty. 2)
M10x150 Carriage Bolt Assemblies
(Qty. 4)
M10x35 Carriage Bolt Assemblies
(Qty. 3)
RF Cables
(Qty. 2)
Elevation Rod Protective Shroud
Below displays the package contents of the TL-ANT5830MD. The TL-ANT2424MD comes with
the Antenna Feed and RF Cables pre-attached.
3
Hardware Overview
Installation Requirements
Pole-mount Clamp
Protective Shroud
Pole-mount Clamp
Antenna-mount Bracket
Dish Reflector
Outdoor Wireless Base Station (sold separately)
Phillips Screwdriver
Wrenches
4
1. Secure the Antenna Feed to the Dish Reflector using the four M4
Bolts and a Phillips screwdriver.
Hardware Installation
2. Connect the RF Cables to the RF Connectors on the Antenna Feed.
Note: Do not handle the Dish Reflector by the Antenna Feed once the feed is installed.
Note: TL-ANT 2424MD doesn't require this step, please go directly to step 3.
5
3. Attach the Base Station to the Dish Reflector as follows:
a. Align the mounting tabs on the back of the Base Station with the
four mounting slots on the Base Station mounting bracket.
b. Slide the Base Station down until it locks into place.
4. Connect the other ends of the RF Cables to the Base Station.
6
5. Attach the Elevation Rod to the Antenna-mount Bracket using the flat
washers and nuts as shown below.
6. Attach the M10x150 Carriage Bolt Assemblies to the Antenna-mount
Bracket：
a. Remove the flat washer, spring washer, and nut that are threaded
on each M10x150 Carriage Bolt Assembly. Set them aside as they
will be used to secure the antenna to a pole in step 8.
b. Insert the four M10x150 Carriage Bolts into the Antenna-mount
Bracket.
7
7. Attach the Dish Reflector to the Antenna-mount Bracket:
a. Secure one M10x35 Carriage Bolt Assembly to attach the Dish
Reflector to the Elevation Rod.
b. Secure two M10x35 Carriage Bolt Assemblies to attach the Dish
Reflector to the lower section of the Antenna-mount bracket.
8. Mount the antenna assembly to the pole using the two Pole-mount
Clamps and the four sets of flat washers, spring washers and nuts of
the M10x150 Carriage Bolt Assemblies.
Note:
1. Pole diameter ranges from 1.5 in to 4.0 in.
2. Do not over-tighten these bolts and nuts to allow angle adjustment later.
3. In step 8 to 9, use the Level Vital to ensure proper alignment.
8
Level Vial
9. Adjust the antenna azimuth and elevation angles with the front facing
the intended signal receiving devices to achieve maximum signal
strength:
a. To adjust azimuth, loosen the four nuts on the Pole-mount Clamps
slightly to pivot the antenna, then tighten the nuts.
b. To adjust the elevation angle, tighten or loosen the Elevation Nuts
on the Elevation Rod to the desired tilt.
10. Slide the Protective Shroud down over the Base Station until it locks
into place.
9
Elevation Nuts
COPYRIGHT & TRADEMARKS
Website: http://www.tp-link.com
Tel: +86 755 26504400
E-mail: support@tp-link.com
Specifications are subject to change without notice.
is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands
and product names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to
make any derivative such as translation, transformation, or adaptation without permission
from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO.,
LTD. All rights reserved.
7106505650 REV1.0.0