Chapter 1 About This Guide
- 1.1 Conventions
- 1.2 Overview of This Guide
Chapter 2 Get to Know Your Camera
Chapter 3 Set Up Your Camera
- 3.1 Set up the Camera with the tpCamera App
- 3.2 Position Your Camera
Chapter 4 Configure Your Camera

TP-Link TL-NC220 User Manual

Displayed below is the user manual for TL-NC220 by TP-Link which is a product in the Security Cameras category. This manual has pages.

NC220

Day/Night Cloud Camera, 300Mbps Wi-Fi

NC230

HD Day/Night Wi-Fi Cloud Camera

NC250

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

1910012149

REV1.1.0

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

 Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause

undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. Such modifications could void the user’s authority to operate the

equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This device and its antenna must not be co-located or operating in conjunction with

any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile

Configurations. The antennas used for this transmitter must be installed to provide a separation

distance of at least 20 cm from all persons and must not be co-located or operating in conjunction

with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

RF Exposure Information

This device meets the EU requirements (1999/5/EC Article 3.1a) on the limitation of exposure of

the general public to electromagnetic fields by way of health protection.

The device complies with RF specifications when the device used at 20 cm from your body.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSSs. Operation is subject to the

following two conditions:

1） This device may not cause interference, and

2） This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

1） l’appareil ne doit pas produire de brouillage;

2） l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le

brouillage est susceptible d’en compromettre le fonctionnement.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20

cm de distance entre la source de rayonnement et votre corps.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements:

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice

注意！

依據低功率電波輻射性電機管理辦法

第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、

加大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即

停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射

頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

減少電磁波影響，請妥適使用。

BSMI Notice

安全諮詢及注意事項

 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

 注意防潮，請勿將水或其他液體潑灑到本產品上。

 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам

нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the

product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and

voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

 Adapter shall be installed near the equipment and shall be easily accessible.

 The plug considered as disconnect device of adapter.

 Use only power supplies which are provided by manufacturer and in the original

packing of this product. If you have any questions, please don't hesitate to contact us.

Explanation of the symbols on the product label

Symbol

Explanation

DC voltage

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic

equipment (WEEE). This means that this product must be handled pursuant to

European directive 2012/19/EU in order to be recycled or dismantled to minimize

its impact on the environment.

User has the choice to give his product to a competent recycling organization or to

the retailer when he buys a new electrical or electronic equipment.

CONTENTS

Chapter 1 About This Guide ................................................................................... 1

1.1 Conventions ................................................................................................................... 1

1.2 Overview of This Guide ................................................................................................. 1

Chapter 2 Get to Know Your Camera ..................................................................... 3

2.1 Product Overview .......................................................................................................... 3

2.2 Main Features................................................................................................................ 3

2.3 Panel Appearance ......................................................................................................... 4

2.3.1 Front Panel......................................................................................................... 4

2.3.2 Rear Panel ......................................................................................................... 5

Chapter 3 Set Up Your Camera .............................................................................. 7

3.1 Set up the Camera with the tpCamera App .................................................................. 7

3.2 Position Your Camera .................................................................................................... 8

Chapter 4 Configure Your Camera ....................................................................... 10

4.1 Log in to Your Camera................................................................................................. 10

4.2 Live View ...................................................................................................................... 11

4.3 Basic ............................................................................................................................ 13

4.3.1 Basic > Status .................................................................................................. 13

4.3.2 Basic > Network ............................................................................................... 15

4.3.3 Basic > Wireless Connection ........................................................................... 16

4.3.4 Basic > Cloud Setting ...................................................................................... 18

4.3.5 Basic > LED ..................................................................................................... 19

4.4 Advanced ..................................................................................................................... 19

4.4.1 Advanced > Status ........................................................................................... 20

4.4.2 Advanced > Network ........................................................................................ 20

4.4.3 Advanced > Wireless Connection .................................................................... 22

4.4.4 Advanced > Wireless Extender ....................................................................... 24

4.4.5 Advanced > Cloud Setting ............................................................................... 25

4.4.6 Advanced > Video ............................................................................................ 25

4.4.7 Advanced > Motion Detection .......................................................................... 27

4.4.8 Advanced > Sound Detection .......................................................................... 28

4.4.9 Advanced > Notification Delivery ..................................................................... 29

4.4.10 Advanced > LED .............................................................................................. 33

4.5 System ......................................................................................................................... 33

4.5.1 Account ............................................................................................................ 34

4.5.2 Date/Time ......................................................................................................... 36

4.5.3 Management .................................................................................................... 38

4.5.4 System Log ...................................................................................................... 39

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Chapter 1 About This Guide

This User Guide contains information for setup and management of the Cloud Camera. When

using this guide, please notice that features may vary slightly depending on the model and

software version you have, and on your location, and language. All images, parameters and

descriptions documented in this guide are used for demonstration only.

1.1 Conventions

In this Guide the following conventions are used:

 The camera mentioned in this Guide stands for NC220, NC230 and NC250 without any

explanation.

 This User Guide is shared by NC220, NC230 and NC250. NC250 is used for demonstration in

this guide. The difference between them are:

1. Max Frame Rate: 30 fps for NC220 at 640x480 (VGA) and 320x240 (QVGA); 20 fps for

NC230 at 1280x720 (HD); NC250 at 1280x720 (HD).

2. Wi-Fi Data Rate: 150Mbps for NC230; 300Mbps for NC220 and NC250.

Symbol in this Guide：

Symbol

Description

Bold font

Indicates a button, a toolbar icon, menu or menu item.

Note:

Ignoring this type of note might result in a malfunction or damage to the

device.

1.2 Overview of This Guide

Chapter

Introduction

Chapter 1 About This Guide

Introduces the guide structure and conventions.

Chapter 2 Get to Know Your

camera

Introduces the features, application and appearance of the

camera.

Chapter 3 Set Up Your Camera

Introduces how to quickly set up the camera using the

tpCamera app and how to position your camera.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Chapter

Introduction

Chapter 4 Configure Your

Camera

Introduces how to configure the camera using the built-in web

management page.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Chapter 2 Get to Know Your Camera

2.1 Product Overview

TP-LINK Cloud Camera is a versatile solution for home and office monitoring to keep an eye on

your home, kids or workplace, whatever you care for most.

TP-LINK Cloud Camera is a cloud-based Wi-Fi video monitoring device with free live streaming

and remote viewing, which makes it easy to stay connected with what you care most wherever you

are. You can view and manage your camera from anywhere over the internet through the TP-LINK

Cloud website or through the tpCamera app for iOS and Android devices.

Through the camera’s web management page, you can view the status of the camera, and

configure lots of settings of the camera, such as network setting, the cloud setting, the motion

detection, and the notification delivery.

With Night Vision function, TP-LINK Cloud Camera lets you view even in darkness.

With Motion Detection function, TP-LINK Cloud Camera can send you immediate notification by

email or FTP whenever motion or sound is detected automatically, allowing you to remain aware of

whatever is happening on the ground.

With a stable high speed Wi-Fi connection of up to 300Mbps for NC220 and NC250, and 150Mbps

for NC230, you can enjoy fluid video streaming with ease. In addition, the TP-LINK Cloud Camera

can also expand your Wi-Fi network with its Wi-Fi Extender functionality.

With the sticky pad or screws, you can place your camera anywhere you want, on the table, the

wall, or even on the ceiling.

2.2 Main Features

 Night Vision - Automatic night vision functionality supports 24-hour surveillance

 tpCamera App - Use the free tpCamera app to set up, view and manage the camera remotely

with your iOS and Android devices

 Easy Setup – Connect and follow the tpCamera app’s instruction to install and operate the

camera within minutes

 TP-LINK Cloud (http://www.tplinkcloud.com) access for easy viewing and management

 Web management page for basic and advanced configurations

 Motion & Sound Detection - Immediate notification by email or FTP whenever motion or sound

is detected

 Email or FTP notification triggered by motion detection

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Wireless connectivity compliant with WPS button

 Instantly eliminates the dead zones and expand your home’s wireless network

 Ethernet port for wired connectivity

 4x digital zoom for close-up viewing

 Advanced H.264 video compression for smooth video streaming

 Support wireless 802.11b/g/n

2.3 Panel Appearance

2.3.1 Front Panel

Figure 2-1 Front Panel

 Light Sensor: The camera has a built-in internal photodetector. It is used to identify day or

night.

 Microphone: The camera has a built-in internal microphone. This microphone is hidden in

the pinhole located on the front panel.

System LED

Microphone

Light Sensor

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 System LED:

Status

Indication

Flashing Red

The camera starts booting up.

Solid Red

The camera has boot up, but is not connected to any network.

Flashing Green

The camera is in firmware upgrade procedure.

Solid Green

The camera is connected to a network or is transferring data.

2.3.2 Rear Panel

Figure 2-2 Rear Panel

 WPS LED:

Status

Indication

Flashing Green

The camera starts booting up.

The camera is connecting to a network by WPS function. This

process will last in the first 2 minutes.

Off

The camera has boot up.

The camera failed to be added to a network by WPS function.

Ethernet Port

WPS LED

Power Jack

WPS/RESET

Button

Ventilation Holes

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Solid Green

The camera has been successfully added to a network by WPS

function. This process will last in the first 2 minutes.

 Ethernet Port: The ethernet port is used to connect the camera to a network via RJ45 cable.

 Power Jack: The power jack is where you connect the power adapter to the camera.

 WPS/RESET Button: This button is used for both WPS and RESET function. To use the WPS

function, press it for 1 second. To use the RESET function, press and hold for more than 5

seconds.

 Used as the WPS button:

If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect the

camera to your Wi-Fi network using WPS. Press the WPS or QSS button on your router.

Within 2 minutes, press the WPS/RESET button on the camera for 1 second, then the

WPS LED will start flashing quickly. When the LED becomes solid on, the camera is

successfully connected to the router wirelessly..

 Used as the RESET button:

With the camera powered on, press and hold the WPS/RESET button for more than 5

seconds until the System LED turns off. Then release the button and wait the camera to

reset to its factory default settings.

 Ventilation Holes: These holes are used for heat dissipation.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Chapter 3 Set Up Your Camera

3.1 Set up the Camera with the tpCamera App

You can install your camera in minutes with the free tpCamera app. If your router has a WPS

button, you can complete the setup wirelessly using WPS function. Please follow the steps below

to set up your camera.

Step 1. Connect the camera to the network your smartphone is on.

Before you start the setup process, get your smartphone and make sure that it is connected to

your home network.

Steps for connecting your camera to the router are:

1) Power on the camera using the provided power supply unit as shown.

2) Connect a smartphone to the router as shown.

3) Connect the camera to the router via wired or wireless connection, and then wait till the

camera’s system LED become solid green.

Wired: Connect the camera to the router’s LAN port via an Ethernet cable.

Wireless: If your wireless router supports WPS, you can connect the camera to your Wi-Fi

network using WPS. Press the WPS or QSS button on your router. Within 2 minutes, press

the WPS/RESET button on the back of the camera for 1 second, then the WPS LED will start

flashing quickly. When the WPS LED becomes solid on, the camera is successfully connected

to the router wirelessly.

SmartphoneCameraOutlet Wireless Router

LAN WAN

Internet

ETHERNET9V 0.6A

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Step 2. Download and install the tpCamera app.

You can download the free tpCamera app from the App Store or Google Play. You can also scan

the QR code below to download the tpCamera app.

Step 3. Add the camera to your TP-LINK cloud account.

Launch the tpCamera app, log in with your TP-LINK cloud account or create one if you do not

have an account. Then follow the app instructions to add your new camera to your account.

When you reach the My Cam page, you have successfully added your camera and can start to

use your camera.

3.2 Position Your Camera

Before positioning your camera, please keep these safety guidelines in mind:

 Keep your camera out of reach of children and pets.

 Use your camera only indoors, and keep it out of direct sunlight. Make sure its operating

temperature is in the range of 0-40°C (32-104°F).

 Pick a location which is close enough to a wall outlet.

 Use only the power adapter that comes with this camera in the package.

You can place your camera to your desired location. Just unplug and replug it without having to go

through the app’s setup again, and then you can use it in a wired or wireless way as you’ve set in

the app’s setup process. If you use the camera wirelessly, please place the camera within the

coverage of your wireless network. You can place the camera in various ways:

 Place it on a flat surface.

 Stick it with the included adhesive.

 Mount it to a wall or ceiling.

Detailed instructions on mounting your camera to a wall or ceiling are shown as follows. Before

you start to mount the camera, prepare two screws which meet the following requirements.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

1. Unscrew the camera head.

2. Remove the base cover.

3. Use two screws (not included) to secure

the base.

4. Put the base cover and camera head back

on.

After relocating your camera, face it towards the area you’d like to view, and then plug the power

adapter into a power outlet.

Now that you’ve finished positioning your camera, use the tpCamera app to check that your

camera can see what you want to keep an eye on. Adjust its position if needed.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Chapter 4 Configure Your Camera

You can use the tpCamera app and TP-LINK Cloud (http://www.tplinkcloud.com) to view and

manage your camera remotely. To configure the camera’s settings, such as the network settings,

cloud settings, notification delivery, you should use the camera’s built-in web management page in

your local network.

4.1 Log in to Your Camera

1. Connect a computer to the router that your camera is connected to. You can use an Ethernet

cable or connect it to the router’s Wi-Fi network.

2. Find the IP address of the camera from the web management page of the router. Here we use

the web management page of TP-LINK router for demonstration.

3. On a computer that connects to the same router as the camera does, open a web browser,

type in the camera’s IP address in the address field, and press Enter. Here we use

http://192.168.0.106 for demonstration.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

4. Enter the default username and password (admin/admin). Click Login.

5. Create a new password for your camera to enhance security. Click OK.

 Note:

For the administrator, the default password is “admin”. For subsequent logins, use your password

you have created.

If you log in to the camera as an administrator, you can perform all the settings provided by the

camera.

If you log in to the camera as a common user, you can only view the Live View. After logging as

administrator, you can add up to five user accounts in the Account menu (Go to “System >

Account”).

4.2 Live View

The Live View screen shows you the live video feed from your camera. On this screen, you can

also capture a picture.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

Symbols

Meaning

Note

Click to capture a still

image shot by the

camera.

The image file will be saved to your local

computer. You can select a save path and rename

the image file.

Click to rotate the current

image.

If the camera is installed upside down, Rotate

Image should be checked.

Click to select the

Auto/Day/Night mode.

Auto: This mode will automatically switch

between Day and Night modes based on the

amount of available lighting.

Day: This sets the camera to always be in

the Day mode.

Night: This sets the camera to always be in

the Night mode.

 Brightness: Drag the slider to adjust the brightness level of

camera. Large value will brighten the current displayed screen.

 Contrast: Drag the slider to adjust the contrast level of the camera.

Large value will contrast the current displayed screen heavily.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Saturation: Drag the slider to adjust the saturation level of the

camera. Large value will saturate the current displayed screen to be more colorful.

 Preset: Click the Preset button to restore to factory image settings.

4.3 Basic

Click the Basic menu to display the submenus including Status, Network, Wireless Connection,

Cloud Setting, and LED.

4.3.1 Basic > Status

The Status page displays the current configuration information of the camera. You can find out

camera’s settings such as wireless connection settings here. All the information is read-only.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

4.3.2 Basic > Network

On this page, you can configure your camera’s IP address which is used to access and configure

the camera.

 Dynamic IP: Select this option when a DHCP server is installed on the network to issue IP

address assignment. With this setting, the IP address of the camera is assigned automatically.

 Static IP: Select this option when a static or fixed IP address is obtained for the camera. A

static IP address will ease your access to the camera in the future. Add your camera’s static

IP information to your router to avoid IP conflicts.

 MAC Address: Displays the Ethernet MAC address of the camera. The MAC address is

read-only.

 IP Address: Enter a fixed IP address for the camera in dotted-decimal notation.

 Subnet Mask: Enter the subnet mask in dotted-decimal notation. The default value is

“255.255.255.0.”

 Default Gateway: Enter the default gateway in dotted-decimal notation.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Primary DNS Server: Enter a DNS address in dotted-decimal notation.

 Secondary DNS Server: Enter a DNS address in dotted-decimal notation.

Click Save to save and enable the settings.

4.3.3 Basic > Wireless Connection

The camera’s wireless function is enabled by default. This function helps to connect your camera

to a wireless network wirelessly. If you don’t want to use this function, just select the Disable

option.

 Wireless Network Name: Displays the wireless network’s name. Make sure the camera and

your PC connect to the same wireless network, or your PC can't access the camera.

 Signal: Displays the strength of the wireless signal.

 Security: Displays the wireless network’s security mode.

 MAC Address: Displays the MAC address of the front device.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

To connect your camera to a wireless network, follow the steps below:

1. Click Scan to scan the available wireless network and to refresh the Wireless Network List.

2. Select a wireless network from the wireless network list.

3. If the wireless network’s security mode is None, simply click Connect. If the security mode

requires a password, enter the wireless network’s password and then click Connect. You can

select Show password to display what you’ve entered.

4. A pop-up screen will prompt you for the network modification. Click Change to continue.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

5. Click OK on the pop–up screen to finish wireless connection procedure.

6. To start using camera wirelessly, unplug its Ethernet cable.

4.3.4 Basic > Cloud Setting

A Cloud Camera can be viewed anytime and anywhere over the Internet with TP-LINK Cloud

service. On this page, you can add the camera to your TP-LINK Cloud account.

 Note:

1. You can register a TP-LINK Cloud account in the tpCamera app only. If you do not get a

tpCamera app, please refer to the Step 2 Download and install the tpCamera app in 3.1

Set up the Camera with the tpCamera APP.

2. To add a camera to your TP-LINK Cloud account, make sure that the camera is connected to

the Internet.

Add Your Camera to TP-LINK Cloud Account

If you already have a TP-LINK Cloud account, to add your camera to your account, just enter the

TP-LINK Cloud account and password, and then click Register.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Account: Enter your TP-LINK Cloud account, either E-mail address or username is allowed.

 Password: Enter your TP-LINK Cloud account’s password.

 Camera Name: The default value is the camera model. You can change it to an

easy-to-remember one. Camera name can contain up to 31 characters. It cannot contain the

following characters: \ / : = & ‘ “ < > { }.

After your camera is registered successfully, you can go to http://www.tplinkcloud.com to view it.

4.3.5 Basic > LED

The camera’s LED is on by default. If you want to turn it off, just select Off.

4.4 Advanced

Click the Advanced menu to display the submenus including Status, Network, Wireless

Connection, Wireless Extender, Cloud Setting, Video, Motion Detection, Sound Detection,

Notification Delivery, and LED.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

4.4.1 Advanced > Status

Refer to 4.3.1 Basic > Status.

4.4.2 Advanced > Network

On this page, you can configure the network settings of the camera.

IP Address

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

On this section, you can configure your camera’s IP address which is used to access and

configure the camera.

 Dynamic IP: Select this option when a DHCP server is installed on the network to issue IP

address assignment. With this setting, the IP address of the camera is assigned automatically.

 Fallback IP: If the camera cannot get a Dynamic IP address from a DHCP server within

limited tries, the camera will assign a default IP address, 192.168.0.10, by itself as the

Fallback IP address.

 Static IP: Select this option when a static or fixed IP address is obtained for the camera. A

static IP address will ease your access to the camera in the future. Add your camera’s static

IP information to your router to avoid IP conflicts.

 MAC Address: Displays the Ethernet MAC address of the camera. The MAC address is

read-only.

 IP Address: Enter a fixed IP address for the camera in dotted-decimal notation.

 Subnet Mask: Enter the subnet mask in dotted-decimal notation. The default value is

“255.255.255.0.”

 Default Gateway: Enter the default gateway in dotted-decimal notation.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Primary DNS Server: Enter a DNS address in dotted-decimal notation.

 Secondary DNS Server: Enter a DNS address in dotted-decimal notation.

HTTP (Hypertext Transfer Protocol)

This feature allows you to access and manage your camera via its IP address. Web browser

access normally uses the standard HTTP service port 80. The camera uses HTTP port 80 by

default. For greater security, you can change the port to a custom one.

When HTTP port is set to 80, you can access the camera by typing its IP address (for example,

http://192.168.1.100) on a web browser. When HTTP port is set to another value (for example,

2000), you need to type http://192.168.1.100:2000 instead.

 HTTP Port: The default value is 80. If you want to use a port number other than 80, enter a

port number between 1 and 65535.

Bonjour

Bonjour, also known as zero-configuration networking, enables automatic discovery of computers,

devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow

devices to automatically discover each other without the need to enter IP addresses or configure

DNS servers.

 Bonjour: To enable or disable the Bonjour service here.

 Bonjour Name: Displays the Bonjour name. By default, it is a combination of model and the

last six characters of the camera’s MAC address.

Click Save to save and enable the settings.

4.4.3 Advanced > Wireless Connection

The camera’s wireless function is enabled by default. With this function enabled, you can connect

your camera to a wireless network wirelessly. If you don’t want to use this function, just select the

Disable option.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

On this page, you can either scan a wireless network to connect to or enter a wireless network’s

parameters manually. To scan a wireless network, refer to 4.3.3 Basic > Wireless Connection. To

enter the parameters manually, see the following.

1. Select Enable to enable your camera’s wireless function.

2. Click Manually, and you will see the following screen.

3. In the Wireless Network Name field, enter the name of the wireless network to which your

camera is ready to connect.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Note:

The name must be exactly the same as that used in the wireless access point, or the connection

will not be established. Leaving this field blank means the camera will attempt to access the

nearest open network. If your PC wants to access the camera, make sure your PC and the camera

are connecting to the same wireless network.

4. Select the wireless security mode used by your wireless network from the drop-down list. The

security mode and its corresponding settings must be exactly the same as that used in the

wireless network.

5. Click Connect and a screen will pop up. Click Change on the pop-up screen.

6. Click OK on the pop–up screen to finish wireless connection procedure.

7. To start using camera wirelessly, unplug its Ethernet cable.

4.4.4 Advanced > Wireless Extender

On this page, you can setup and configure the wireless network extending feature of your camera.

Wireless extender function allows your camera to extend the range of your existing wireless

network. You can use the same network name and settings as the existing wireless network, or

you can create a new one.

The camera’s wireless extender function is disabled by default. If you want to use this function, just

select the Enable option.

 Host Wireless Network Name: Displays the name of the wireless network which your

camera is connected to. It is read-only.

 Extended Wireless Network Name: Name of the wireless network that your camera will

extend.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Same as Host: The extended network will use the same name and settings as your Host

network. Your devices can use the same wireless information to connect to both the host

and extended networks.

 Create a New One: Select this to manually set the name and security used for the

extended network. You devices can use the wireless parameters you set to connect to the

extended network.

 Max Clients: Set the maximum number of clients that are allowed to connect to the extended

network.

Click Save to save and enable the settings.

4.4.5 Advanced > Cloud Setting

Refer to 4.3.4 Basic > Cloud Setting.

4.4.6 Advanced > Video

On this page, you can configure the video settings for your camera.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Coding Format: Displays the video coding format of the camera.

 Resolution: Displays the video resolution of the camera. Higher resolution offers better

quality, but will require more bandwidth to stream.

 Frame Rate: Select the frame rate to use for the video stream from the drop-down list. Higher

settings offer smoother video streams, but will require more bandwidth.

 Mode: Displays the bit rate mode of the camera. This camera uses the VBR (variable bit rate)

mode. In this mode, the bit rate varies to keep consistent video quality. It allows a higher bit

rate (and therefore requires more bandwidth) to be allocated to dynamic scenes while less bit

rate to be allocated to static scenes.

 Image Quality: Select the image quality from the drop-down list: Normal and Low. Normal

settings offer better quality, but it may require more bandwidth to stream.

 Backlight Compensation: If enabled, this feature will compensate for bright backgrounds so

foreground objects aren't silhouetted. It is disabled by default.

Enabled

Disabled

 Light Frequency: Select the frequency used by your lighting and power to help reduce image

flicker. The default setting is auto, which is recommended.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Time Stamp&On-Screen Display (OSD): If enabled, the current time of your camera, which

can be set on the System > Date/Time page, will be displayed on the Live View screen.

Meanwhile, you can set the OSD text to be displayed with the time stamp. The OSD text is

camera name by default.

Enabled

Disabled

Click Save to save and enable the settings.

4.4.7 Advanced > Motion Detection

Motion detection allows you to specify areas of your camera’s video to monitor for motion, which

can be used to trigger snapshots. Refer to 4.4.9 Advanced > Notification Delivery for more details.

2015-05-10 09:51:21

NC250

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Motion Detection: To enable or disable the motion detection function. The area with blue

mask indicates that it is the area with motion detection on. All areas are selected by default.

You can drag your mouse to draw specific areas that you want to monitor.

 Sensitivity: Specify the level of difference between two sequential images that would indicate

motion. Select one of the three levels of sensitivity from the drop-down list: High, Medium, and

Low.

Click Save to save and enable the settings.

4.4.8 Advanced > Sound Detection

Sound detection allows your camera to detect a loud sound, which can be used to trigger

snapshots. Refer to 4.4.9 Advanced > Notification Delivery for more details.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Sound Detection: To enable or disable the sound detection function.

 Sensitivity: Specify the level of difference between current sound and the threshold you set.

Select one of the three levels of sensitivity from the drop-down list: High, Medium, and Low.

 Threshold: Select the threshold of sound level. Snapshots will be triggered when current

sound exceeds this threshold. You can also drag the arrow in the diagram to set the threshold.

Click Save to save and enable the settings.

4.4.9 Advanced > Notification Delivery

Notification Delivery settings are available only after the motion detection or sound detection

function is enabled. It is used to inform you immediately by sending the snapshots triggered by a

detected motion or sound to the specified FTP server or E-mail address.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

FTP

Select FTP, you can configure your camera to send snapshots to a specified FTP sever on the

following screen:

 FTP Server/ Port: Enter the IP or the domain (IP/domain without prefix ftp://) and the port of

the FTP server that you will be connecting to. The port is 21 by default.

 Note:

The FTP server you set and the camera should be in the same LAN.

 Username: Enter the username that is used to log in to your FTP server.

 Password: Enter the password that is used to log in to your FTP server.

 Path: Enter the path to the destination on the FTP server.

 Passive Mode: Enabling passive mode may help you reach your FTP server if your camera is

behind a router protected by a firewall.

To set up a FTP to receive notification, follow the steps below:

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

1. Enter an IP address or domain of your FTP server, e.g. 192.168.1.168

2. Remain the FTP port number as the default value: 21.

3. Enter your username to log in to the FTP server, e.g. test.

4. Enter your password to log in to the FTP server.

5. Enter the path to the destination on the FTP server, e.g. /test

6. Enable Passive Mode.

7. Click Save to save and enable the settings.

Click Test, and a test JPEG snapshot will be sent to the specified FTP server to check whether

your settings are correct.

If the settings are tested correct, click OK.

If the settings are tested incorrect, check your network and FTP settings and try again later.

E-mail

Select E-mail, you can configure your camera to send snapshots to a specified E-mail address on

the following screen.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Recipient E-mail Address: Enter the receiver’s E-mail address that the notification E-mail

will be sent to. Click Add recipient to add receiver’s E-mail addresses. You can specify up to

four recipient E-mail addresses.

 Sender E-mail Address: Enter the sender’s E-mal address that is used to send the

notification E-mail.

 Password: Enter your password if the SMTP server uses authentication.

 SMTP Server/Port: Enter the domain name or IP address and the port of your external E-mail

server. The port is 25 by default.

 SSL Encryption: Select TLS or STARTTLS as the SSL encryption; select Close to disable

SSL encryption.

 Note:

If TLS is selected, SMTP server port should be 465; if STARTTLS is selected, SMTP server

port should be 25 or 587.

 Sending Interval: Set the limit for how frequently E-mail notifications will be sent. Select one

interval from the drop-down list.

For example, if you want to use Gmail with TLS for E-mail notifications, follow the steps

below:

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

1. Enter the receiver’s E-mail address in Recipient E-mail Address, e.g. test@tp-link.com.

2. Enter your E-mail address in Sender E-mail Address, e.g. test@gmail.com.

3. Enter the password required to access the SMTP server.

4. Enter smtp.gmail.com in SMTP server.

5. Select TLS as the SSL encryption and the SMPT server port number will be changed to 465

automatically.

6. Set the Sending Interval, e.g. 1m.

7. Click Save to save and enable the settings.

Click Test, and a test JPEG snapshot will be sent to the recipient E-mail address to check whether

your settings are correct.

If the settings are tested correct, click OK.

If the settings are tested incorrect, check your network and E-mail settings and try again later.

4.4.10 Advanced > LED

Refer to 4.3.5 Basic > LED.

4.5 System

Click the System menu to display the submenus including Account, Date/Time, Management,

and System Log.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

4.5.1 Account

On this page, you can change the administrator’s password and manage the user account(s) that

are allowed to access to your camera.

 Username: Displays the name of user account.

 User Group: Displays the group that the user account is in. Different user group has different

limits of authority.

 admin: This group has all authority of configuration. It can only have one account: admin.

 user: This group can only view the Live View. It can have up to five accounts.

Add a New User Account

You can create a new user account to provide viewing access for your camera’s video. User

accounts will only be able to access the Live View section of the web configuration page, but

cannot access any other parts or change any settings.

To add a new user account, follow the steps below:

1. Click Add, and you will see the following screen.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

2. Enter a username for your new account.

3. Enter a password for your new account. The password should contain 5 to 20 characters.

4. Enter the password again to confirm it.

5. Click Save to save and enable the settings.

Change Password

You can change the password of all the accounts here.

 Note:

The default account and password are both admin. Everyone who knows the camera’s IP address

can access the device with all configuration authority. It is necessary to change the default

password if the device is intended to be accessed only by administrator.

To change password, follow the steps below:

1. Select a user account in the list whose password you want to change

2. Click Change Password, and you will see the following screen.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

3. Enter the current password in the Old Password textbox.

4. Enter a new password.

5. Enter the new password again to confirm it.

6. Click Save to save and enable the settings.

Delete a User Account

You can delete a user account except admin here. Click a user entry in the list and click Delete.

4.5.2 Date/Time

On this page, you can configure the settings of the internal system clocks for your camera.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Current Time: Displays the current date and time of the camera.

 Time Zone: Select the time zone for the region where the camera is installed.

 Synchronize With NTP Server: Select this option to specify the NTP server name to

synchronize the date and time of the camera with those of the time server, known as the NTP

(Network Time Protocol) server. If enabled, you will see the following screen:

 NTP Server: You can either enter a domain name of the NTP server or select one which

will be filled in automatically from the drop-down list.

 Set NTP Server from Dynamic IP: You can use the NTP server applied in the DHCP

server on the network.

 Set Date and Time Manually: Select this option to set the date and time of the camera

manually. If enabled, you will see the following screen:

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Copy Your Computer’s Time Settings: Click this button to copy your computer’s current

time settings.

Click Save to save and enable the settings.

4.5.3 Management

On this page, you can reboot the camera, backup and restore the camera’s current settings, reset

factory settings, and update the camera’s software.

 Reboot: Click Reboot and then click Reboot on the pop-up screen to confirm. Rebooting will

not change the camera’s setting. After rebooting, you need to log in to this page again.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Backup: Click Backup and follow the instructions on the browser to save the setting data file

to your specified location.

 Restore: Click Browse to locate the saved backup file and then click Restore. The camera

will start rebooting and then the settings will be restored to the previous configuration.

 Reset: Click Reset and then click Reset on the pop-up screen to restore the camera to its

factory defaults. Don't turn off the camera while resetting. After resetting, you need to find out

the IP address of your camera (refer to 4.1 Log in to Your Camera) and use the default

username and password (admin/admin) to log in to this page.

 Update: Before update, download the latest firmware from the product page at

http://www.tp-link.com, and then use decompression software to extract the file. Click Browse

to locate the latest downloaded software file, and then click Upgrade to update the camera’s

software to the latest version. Wait for the upgrading process to complete, and the camera will

reboot automatically.

 Note:

1. We recommend that you use a wired connection for your camera and PC when upgrading

firmware.

2. The firmware upgrade procedure must not be interrupted or the camera may be damaged.

3. The firmware upgrade procedure is always risky and do not try to upgrade new firmware if it’s

not necessary.

4.5.4 System Log

On this page, you can review any changes and events happened to your camera. The system

starts logging automatically after startup.

NC220

NC230

NC250

Day/Night Cloud Camera, 300Mbps Wi-Fi

HD Day/Night Wi-Fi Cloud Camera

HD Day/Night Cloud Camera, 300Mbps Wi-Fi

 Time: Displays the time when the log event occurs. The log can get the correct time after you

configure on the Date/Time page. (go to Advanced > Date/Time)

 Module: Displays the module to which the log information belongs. You can specify the

module by selecting one from the Module drop-down list at the bottom.

 Level: Displays the severity level of the log information. You can specify the level by selecting

one from the Level drop-down list at the bottom.

 Content: Displays the details of the log information.

 Refresh: Click Refresh to refresh the log information.

 Save Log: Click Save Log and follow the instructions on the browser to save the log to your

specified location.

 Clear Log: Click Clear Log to clear all the log information.

Table of Contents

TP-Link TL-NC220 User Manual