TP-Link TL-POE2412G User Manual
Displayed below is the user manual for TL-POE2412G by TP-Link which is a product in the PoE Adapters category. This manual has pages.
7106508124 REV1.0.2
Installation Guide
Passive PoE Adapter
Connection
Use the passive PoE adapter to simultaneously supply power and transmit data to a passive PoE device.
AC Power Cord
Passive PoE Adapter
TL-POE2412G/TL-POE4824G
Installation
Package Contents: passive PoE adapter, power cord, wall mount kits
Ethernet Device
(switch, router, etc.)
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code
2. Attach the passive PoE adapter to the mounting bracket by sliding the
adapter in the direction of the arrows until it locks into place.
IP Camera AP CPE
Passive PoE Devices
Note: To ensure the passive PoE adapter is attached most securely, it is recommended to install the adapter with the Ethernet port facing upward.
1. Drill two holes on the wall and insert the plastic wall anchors into the
the holes. Secure the mounting bracket to the wall. Make sure the
shoulders at the corners of the mounting bracket are on the outside
and pointing upward.
Note: Before connecting a passive PoE device, please check the required voltage in its product manual.
Note: TL-POE2412G is used as an example throughout this guide. Other models may dier in appearance.
FAQ
A: Yes. Both the LAN and the PoE ports of the PoE adapter
comply with IEEE 802.3i and IEEE 802.3u standards and support
10/100Mbps Auto-Negotiation.
Q1. Can the PoE adapter supply power to a passive PoE device
which doesn’t have a gigabit Ethernet port?
Q2. Can the Passive PoE adapter supply power to all my PoE
devices?
A: If your devices support passive PoE and the voltage
standards of the devices match that of the passive PoE adapter,
the passive PoE adapter can supply power to them.
Specications
IEEE802.3i, IEEE 802.3u, IEEE 802.3abStandards
General Specications
Ports 10/100/1000Mbps Auto-Negotiation RJ45 LAN port
10/100/1000Mbps Auto-Negotiation RJ45 POE port
UTP/STP of Cat. 5e or above (based on the
standards that the connected devices comply with)
Cable Type
Output Power
PWRLED
TL-POE2412G: 24V/0.5A
TL-POE4824G: 48V/0.5A
This is a class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
CE Mark Warning
Do not use this product near water, for example, in a wet basement or near a swimming
pool.
Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
SAFETY NOTICES
Cautions
FCC STATEMENT
© 2018 TP-Link
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність
вимогам нормативних документів та вимогам, що передбачені чинними
законодавчими актами України.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
TP-Link hereby declares that the device is in compliance with the essential requirements
and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC and
2011/65/EU.
The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce.
Operationg Temperature 0˚C to 40˚C (32˚F to 104˚F)
Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)
Storage Humidity 5% to 90%RH non-condensing
Operationg Humidity 10% to 90%RH non-condensing
Environmental and Physical Specications
Explanation of the symbols on the product label
DC voltage
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic equipment
(WEEE). This means that this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.
User has the choice to give his product to a competent recycling organization or to the retailer
when he buys a new electrical or electronic equipment
Indoor use only
AC voltage
Energy eciency Marking
限用物質含有情況標示聲明書
產品元件名稱
限用物質及其化學符號
PCB
外殼
電源線
鉛
Pb
鎘
Cd
汞
Hg
六價鉻
CrVI
多溴聯苯
PBB
多溴二苯醚
PBDE
備考1. "超出0.1 wt %" 及 "超出0.01 wt %" 系指限用物質之百分比含量超出百分比含量基準值。
備考2. "○"系指該項限用物質之百分比含量未超出百分比含量基準值。
備考3. " - " 系指該項限用物質為排除項目。
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment o and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
LED & Button
Power
On: Power on
O: Power o