TP-Link TL-SG1210P User Manual
Displayed below is the user manual for TL-SG1210P by TP-Link which is a product in the Network Switches category. This manual has pages.
Connection
© 2020 TP-Link 7106508827 REV4.1.0
Installation Guide
Gigabit Desktop PoE+ Switch
LED Explanation
Package Contents: Switch, Power Adapter, Power Cord and Installation Guide.
Note: For simplicity, we will take TL-SG1008P for example throughout the Guide.
PC
IP Camera AP
Ethernet Ports (1-8)
PoE Ports (1-4)
IP Phone
PoE Devices
Router
LAN PortWAN Port
Internet
DC Power Adapter
AC Power Cord
Note:
3. For TL-SG1008P, maximum PoE power is 30 W for each PoE port and 64 W for all PoE ports in total.
For TL-SG1210P, maximum PoE power is 30 W for each PoE port and 63 W for all PoE ports in total.
For TL-SG1210MP, maximum PoE power is 30 W for each PoE port and 123 W for all PoE ports in total.
2. PoE ports typically connect to PoE Devices. Besides, PoE ports can also connect to non-PoE
devices, but only transmit data.
1. TL-SG1210P/TL-SG1210MP has two uplink ports, which typically connect to uplink devices like routers.
Uplink 1 is an SFP port and works with a 1000 Mbps SFP module. Uplink 2 is an RJ45 port.
PoE budget calculations are based on laboratory testing. Actual PoE power budget is not guaranteed
and will vary as a result of client limitations and environmental factors.
PoE Disclaimer:
Power PoE Status
On: Providing PoE power
Flashing: PoE fault
O: Not providing PoE power
On: Power on
O: Power o
Link/Act; Uplink 1, Uplink 2
Green On:
Running at 1000 Mbps, but no activity.
Green Flashing:
Running at 1000 Mbps and is transmitting or
receiving data.
Yellow On:
Running at 10/100 Mbps, but no activity.
O:
No device is linked to the corresponding port.
Yellow Flashing:
Running at 10/100 Mbps and is transmitting
or receiving data.
PoE MAX
For TL-SG1008P:
On: 57 W≤Total power supply < 64 W
Flashing: Total power supply ≥ 64 W
O: Total power supply < 57 W
For TL-SG1210P:
On: 56 W≤Total power supply < 63 W
Flashing: Total power supply ≥ 63 W
O: Total power supply < 56 W
For TL-SG1210MP:
On: 116 W≤Total power supply < 123 W
Flashing: Total power supply ≥ 123 W
O: Total power supply < 116 W
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the
Power LED is not lit, please try the following:
A1: Make sure the AC power cord is connected to the switch with power source
properly.
A2: Make sure the voltage of the power supply meets the requirements of the
input voltage of the switch.
A3: Make sure the power source is on.
Q1. Why is the Power LED not lit?
Please try the following:
A1: Make sure that the cable connectors are rmly plugged into the switch and
the device.
A2: Make sure the connected device is turned on and works normally.
A3: The cable must be less than 100 meters long (328 feet).
Q2. Why is the Link/Act LED not lit while a device is connected to
the corresponding port?
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90%RH non-condensing
5% to 90%RH non-condensing
Environmental and Physical Specications
IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x,
IEEE 802.3af, IEEE 802.3at, IEEE 802.1p
IEEE 802.3z (Only for TL-SG1210P/TL-SG1210MP)
CSMA/CD
For TL-SG1008P:
8 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation
MDI/MDIX;
PoE Ports: Port 1-Port 4
For TL-SG1210P/TL-SG1210MP:
9 10/100/1000 Mbps RJ45 Ports, Auto-Negotiation
MDI/MDIX; 1 1000 Mbps SFP port;
PoE Ports: Port 1-Port 8
10BASE-T: UTP category 3, 4, 5 cable (maximum 100 m);
EIA/TIA-568 100 Ω STP (maximum 100 m)
100BASE-TX: UTP
category
5, 5e
cable (maximum
100
m);
EIA/TIA-568 100 Ω STP (maximum 100 m)
1000BASE-T: UTP
category 5e cable or above (maximum
100 m); EIA/TIA-568 100 Ω STP (maximum 100 m)
1000BASE-SX/LX/LX10/BX10: MMF, SMF
(Only for
TL-SG1210P/TL-SG1210MP)
TL-SG1008P: 16 Gbps
TL-SG1210P/TL-SG1210MP: 20 Gbps
4K
Store-and-Forward
Automatically learning, automatically aging
Input: 100-240 V AC, 50/60 Hz
Output: 53.5 V DC/2.43 A (For TL-SG1210MP)
53.5 V DC/1.31 A (For TL-SG1008P/TL-SG1210P)
Ye s
TL-SG1008P: 105 mm
TL-SG1210P/TL-SG1210MP: 150 mm
Standard
General Specications
Specications
Q3. Why is PoE/PoE+ Port not supplying power for PoE devices?
If total power consumption of connected PoE devices exceeds the maximum, the
system will cut o the power to ports with the lowest PoE priority. A PoE port with
a smaller index number has a higher PoE priority.
Take TL-SG1008P as an example. If port 1, 2 and 4 are consuming 15.4 W
respectively, and an additional PoE device with 19 W is connected to port 3, the
total power consumption exceeds 64 W, so the system will cut o the power to
port 4.
Power Supply
MAC Address Learning
Transfer Method
MAC Address Table
Backbone Bandwidth
Network Media (Cable)
Interface
Protocol
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome
to email techwriter@tp-link.com.cn.
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
EU Declaration of Conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other
relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce
Wall Mountable
Distance Between
Mounting Holes
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Place the device with its bottom surface downward.
Use only power supplies which are provided by manufacturer and in the original packing of this
product. If you have any questions, please don’t hesitate to contact us.