TP-Link TL-WR941HP User Manual

Displayed below is the user manual for TL-WR941HP by TP-Link which is a product in the Wireless Routers category. This manual has pages.

Access Point Mode

[This mode transforms your existing wired network to a wireless network. ][This mode boosts your home wireless coverage.]

1. Connect the router to your wired host router’s Ethernet port via

an Ethernet cable as shown above.

2. Connect a computer to the router via an Ethernet cable or

wirelessly by using the SSID (wireless name) and password

printed on the bottom label of the router.

3. Launch a web browser and enter http://tplinkwifi.net or

http://192.168.0.1. Use admin for both the username and

password to log in.

4. Click on the top-right corner of the Web Management

Page and choose Access Point and then click Save. The router

will reboot automatically.

Mode

Quick Installation Guide

Start Here >>

Connect to the wireless network by using the SSID (wireless name)

and password of the router.

FASTER

AND

STRONGER

Configure

1. Connect a computer to the router via an Ethernet cable or

wirelessly by using the SSID (wireless name) and password

printed on the bottom label of the router.

2. Launch a web browser and enter http://tplinkwifi.net. Use

admin for both the username and password to log in.

3. Follow Quick Setup to configure.

Make sure to choose

Range Extender

and click

Survey

to choose

your host network and fill in its wireless password.

Option Two: Using Web Browser

Option One: Using RE Button

1. Press the WPS button on the host router.

2. Within 1 minute, press and hold the (RE) button on the

top panel of router for about 3 seconds. The router will start

to reboot.

3. After rebooted, the RE LED should change from blinking to a

solid state, indicating a successful connection.

If not, please refer to the Option Two.

Using the RE button is an easy way to extend your host network.

We recommend you to use this way if your host router has the

WPS button. The button might look like these: WPS

The extended network shares the same SSID (wireless name) and

password as your host network.

Place the router between your host router and the Wi-Fi “dead”

zone. The location you choose must be within the range of

your existing host network.

Relocate

Extended NetworkHost Network

Client

Host Router High Power Router

ClientHigh Power RouterWired Host Router

Ethernet4Ethernet3Ethernet1 Ethernet2Internet

Tether App

TP-LINK Tether provides the easiest way

to manage your router. Search for

TP-LINK Tether in the Apple App Store or

Google Play, or simply scan the QR code

to download Tether App.

Range Extender Mode

Router Mode Troubleshooting

Connect your device to the router and check the LED lights. Configure the router.

Launch a web browser and enter http://tplinkwifi.net or http://192.168.0.1.

Use admin for both username and password to log in, then follow Quick

Setup to complete the configuration.

If you have customized the SSID (wireless name) and password during the

configuration, you will have to reconnect your wireless devices to the new

wireless network.

[This mode enables multiple users to share Internet connection via an ADSL/Cable Modem. If your Internet connection is through an Ethernet cable from the

wall instead of through a modem, connect the Ethernet cable directly to the router’s Internet port, and skip Step 1, 2, 4.]

Wired:

Connect your computer to the

router’s Ethernet port via an

Ethernet cable.

Wireless:

Connect wirelessly by using the SSID

(wireless name) and password printed

on the bottom label of the router.

ON ON ON ON ON ON ON

Note: Restoring the router to its factory defaults will clear all previous conguration.

1. What can I do if I cannot log into the router’s Web Management Page?

If the computer is set to a static or fixed IP address, change the setting to obtain an

IP address automatically.

Verify if http://tplinkwifi.net or http://192.168.0.1 is correctly entered in the web

browser.

Use another web browser and try again.

Reboot your router and try again.

Disable and enable the network adapter in use again.

Clear browsing data and cookies of the browser.

2. What can I do if I cannot access the Internet?

Check if the Internet is working properly by connecting a computer directly to the

modem via an Ethernet cable. If not, contact your Internet Service Provider.

Log into the Web Management Page, and run the Quick Setup again.

Reboot your router and try again.

For cable modem users, reboot the modem. If the problem still exists, log into the

Web Management Page of the router, and go to Advanced > Network > MAC

Clone, click Clone MAC Address and then click Save.

3. What can I do if I forgot my wireless network password?

If you have not changed the default Wireless Password, it can be found on the

product label at the bottom of the router.

Log into the Web Management Page, go to Basic (or Setting) > Wireless to retrieve

or reset your wireless password.

4. How do I restore the router to its factory default settings?

While the router is powered on, press and hold the Reset button on the back panel

of the router until all the LEDs turn back on momentarily.

Log into the Web Management Page of the router, and go to Advanced (or

Setting)> System Tools > Factory Defaults, and click Restore. The router will

restore and reboot automatically.

5. What can I do if I forgot my password of the router’s Web Management

Page ?

Refer to Troubleshooting > 4 to reset the router, and then use the default admin

(all lowercase) for both username and password to log in.

For more information about the configuration, refer to User Guide which can be

downloaded in Support page at http://www.tp-link.com.

Turn off the modem, and

remove the backup battery if it

has one.

Replace the battery, turn on the

modem and wait about 2

minutes for it to restart.

Connect the modem to the

Internet port on the router

via an Ethernet cable.

Turn on the router.

Modem

Install antenna

Please note: The Router provides three working modes: Router,

Range Extender and Access Point. You can choose the mode to

better suit your network needs and follow the guide to

complete the configuration.

Remove the cap from

the router.

Slide the cap onto the

antenna until it xes into

place.

Position the antenna

vertically for best Wi-Fi

performance.

B. Make sure that the

adjustable elbow is facing

up when attached.

A. Insert and screw the

antenna into the antenna

socket.