Table of Contents
TP-Link TX-6610 User Manual
Displayed below is the user manual for TX-6610 by TP-Link which is a product in the Optical Network Terminals/Units (ONTs/ONUs) category. This manual has pages.
TX-6610
1-Port Gigabit GPON Terminal
REV: 3.0.0
1910011424
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
BSMI Notice
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
Adapter shall be installed near the equipment and shall be easily accessible.
The plug considered as disconnect device of adapter.
Use only power supplies which are provided by manufacturer and in the original
packing of this product.
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SG SK TR UA US
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: 1-Port Gigabit GPON Terminal
Model No.: TX-6610
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents：
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 +A2: 2013
The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2015-09-25
TP-LINK TECHNOLOGIES CO., LTD
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
CONTENTS
Chapter 1. Product Overview ................................................................................... 1
1.1 Product Overview .......................................................................................................... 1
1.2 Main Features ............................................................................................................... 1
1.3 Panel Layout ................................................................................................................. 2
1.3.1 The Front Panel ....................................................................................................................2
1.3.2 The Back Panel .....................................................................................................................3
Chapter 2. Connecting the Terminal ....................................................................... 4
2.1 System Requirements ................................................................................................... 4
2.2 Installation Environment Requirements ......................................................................... 4
2.3 Connecting the Terminal ............................................................................................... 4
Chapter 3. Quick Installation Guide ........................................................................ 6
3.1 TCP/IP Configuration .................................................................................................... 6
3.2 Quick Installation Guide ................................................................................................ 9
Chapter 4. Configuring the Terminal ..................................................................... 11
4.1 Login ........................................................................................................................... 11
4.2 Status.......................................................................................................................... 11
4.3 Network Setting ........................................................................................................... 13
4.3.1 PON Certification ............................................................................................................... 13
4.3.2 VLAN Setting ..................................................................................................................... 14
4.3.3 LAN Setting ........................................................................................................................ 15
4.4 Management ............................................................................................................... 16
4.4.1 User Management ............................................................................................................. 16
4.4.2 Firmware Upgrade ............................................................................................................. 17
4.4.3 Factory Defaults ................................................................................................................. 18
4.4.4 Reboot ............................................................................................................................... 18
Appendix A: Specifications ................................................................................... 19
Appendix B: Troubleshooting ............................................................................... 20
TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 1. Product Overview
Thank you for choosing the TX-6610 1-Port Gigabit GPON Terminal.
1.1 Product Overview
TP-LINK’s TX-6610 is a next-generation Gigabit Passive Optical Network (GPON) terminal, ideal
for Fiber to the Home solution. It’s an incredibly robust device allowing users to access high-speed
internet connections via its GPON port and share it with a Gigabit Ethernet port. With the
transmission rates of up to 2.488Gbps, one GPON port and one Gigabit Ethernet port, the
TX-6610 provides high-performance forwarding capabilities to ensure smooth VoIP, HD video
streaming experiences.
In this guide, Terminal stands for the device TX-6610.
1.2 Main Features
Complies with ITU G.984.1, ITU G.984.2, ITU G.984.3 and ITU G.984.4 provides users
comprehensive GPON network compatibility
Downstream rates of up to 2.488Gbps and upstream rates up to 1.244Gbps
Gigabit port ensures rapid transfer speeds
Quality of Service control for traffic prioritization and bandwidth management
Quick and hassle-free installation
Intelligent power-saving method
Built-in DHCP server
1
TX-6610
1-Port Gigabit GPON Terminal User Guide
1.3 Panel Layout
1.3.1 The Front Panel
Figure 1-1
The GPON Terminal’s LEDs are located on the front panel. They indicate the device’s working
status. For details, please refer to LED Explanation.
LED Explanation:
Name Status Indication
Power
On Power is on.
Off Power is off.
GPON
On The Terminal is registered with the ISP.
Flashing The Terminal is trying to register with the ISP.
Off The Terminal is not yet registered with the ISP.
LOS
On The Terminal is unable to transmit optical signal.
Flashing
No optical signal is received or the received signal is too
weak.
Off The Terminal is receiving optical signal properly.
2
TX-6610
1-Port Gigabit GPON Terminal User Guide
LAN
On A device is connected to the LAN port.
Flashing The LAN port is transmitting or receiving data.
Off No device is connected to the LAN port.
1.3.2 The Back Panel
Figure 1-2
ON/OFF: The switch for the power.
POWER: The Power plug is where you will connect the power adapter.
RESET: There are two ways to reset the Terminal's factory defaults.
Method one: With the Terminal powered on, use a pin to press and hold the Reset button for
at least 5 seconds. And the Terminal will reboot to its factory default settings.
Method two: Restore the default setting from Management Factory Defaults of the
Terminal's Web-based utility.
GPON: The GPON is where you will connect the fiber.
LAN: Through the port, you can connect the Terminal to your PC or the other Ethernet
network devices.
3
TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 2. Connecting the Terminal
2.1 System Requirements
Broadband Internet Access Service (GPON).
PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.
TCP/IP protocol on each PC.
Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
2.2 Installation Environment Requirements
The Product should not be located where it will be exposed to moisture or excessive heat.
Place the Terminal in a location where it can be connected to the various devices as well as to
a power source.
Make sure the cables and power cord are safely placed out of the way so they do not create a
tripping hazard.
The Terminal can be placed on a shelf or desktop.
Keep away from the strong electromagnetic radiation and the device of electromagnetic
sensitive.
2.3 Connecting the Terminal
Before installing the device, please make sure your broadband service provided by your ISP is
available. If there is any problem, please contact your ISP. Before cable connection, cut off the
power supply and keep your hands dry. You can follow the steps below to install it.
Step 1: Connect the fiber. Plug one end of the fiber into the GPON port on the rear panel of
TX-6610, and insert the other end into the wall socket.
Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s
Ethernet port or a regular hub/switch port, and the other end to the LAN port on the
TX-6610.
Step 3: Power on the computers and LAN devices.
Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear
of the device and plug in the adapter to an electrical outlet or power extension. The
electrical outlet shall be installed near the device and shall be easily accessible.
Step 5: Press the ON/OFF button of your Terminal.
4
TX-6610
1-Port Gigabit GPON Terminal User Guide
Figure 2-1
5
TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 3. Quick Installation Guide
3.1 TCP/IP Configuration
After you directly connect your PC to the Terminal TX-6610 or connect your adapter to a
Hub/Switch which has connected to the Terminal, you need to configure your PC’s IP address. We
use the procedures in Windows 7 as an example, for other systems refer to T4 for instructions.
Step 1: Right-click Network icon(e.g. ) on the system tray, and select “Open Network and
Sharing Center > Change adapter settings”.
Step 2: Right click the icon that showed below, select Properties on the prompt page.
Figure 3-1
6
TX-6610
1-Port Gigabit GPON Terminal User Guide
Step 3: In the prompt page that showed below, double click on the Internet Protocol Version 4
(TCP/IPv4).
Figure 3-2
7
TX-6610
1-Port Gigabit GPON Terminal User Guide
Step 4: Select both Obtain an IP address automatically and Obtain DNS server address
automatically. Then click OK.
Figure 3-3
Step 5: Back to previous interface, click OK to save the settings.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select run tab, type cmd or command in the field
and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
Terminal has been established.
Figure 3-4
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the Terminal.
8
TX-6610
1-Port Gigabit GPON Terminal User Guide
Figure 3-5
You can check it following the steps below:
1) Is the connection between your PC and the Terminal correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should
be lit.
2) Is the TCP/IP configuration for your PC correct?
If the Terminal's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254.
3.2 Quick Installation Guide
With a Web-based utility, it is easy to configure and manage the TX-6610 1-Port Gigabit GPON
Terminal. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web
browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
1. To access the configuration utility, open a web-browser and type the default address
http://192.168.1.1 in the address field of the browser.
Figure 3-6
After a moment, a login window will appear, similar to the Figure 3-7. Enter admin for the
Username and Password, both in lower case letters. Then click the Login button or press the
Enter key.
Figure 3-7
Note:
1) Do not mix up the username and password with your Terminal account username and
password which are needed for PPP connections.
9
TX-6610
1-Port Gigabit GPON Terminal User Guide
2) If the above screen does not pop up, it means that your Web-browser has been set to a proxy.
Go to Tools menu→Internet Options→Connections→LAN Settings, in the screen that
appears, cancel the Using Proxy checkbox, and click OK to finish it.
2. After your successful login, you will see the Login screen as shown in Figure 3-8. Click
Network Setting PON Certification to complete the PON setting. You are required to
enter GPON Password or GPON SN or both provided by your ISP to pass the ISP
authentication. For details, please consult your ISP. Click Save to make your settings take
effect.
Figure 3-8
3. Establish your Internet connection according to the ISP's specific instructions, such as a
dial-up connection. For details, please refer to T1 in Troubleshooting.
Note:
If you need assistance, contact your ISP.
10
TX-6610
1-Port Gigabit GPON Terminal User Guide
Chapter 4. Configuring the Terminal
This chapter will show each Web page's key function and the configuration way.
4.1 Login
After your successful login, you will see the main menus on the left of the Web-based utility. On
the right, there are the corresponding explanations and instructions.
The detailed explanations for each Web page’s key function are listed below.
4.2 Status
Choose “Status”, you can see the corresponding information about System Status, LAN, PON
and Statistics.
11
TX-6610
1-Port Gigabit GPON Terminal User Guide
Figure 4-1
12
TX-6610
1-Port Gigabit GPON Terminal User Guide
System Status: Here shows the system information of the Terminal.
LAN: The current port status of the Terminal.
PON: Here shows the Terminal’s current GPON module information.
Statistics: Here you can view the statistics of the Terminal.
Click Refresh to update this page.
4.3 Network Setting
Choose “Network Setting”, there are three submenus under the main menu. Click any one of
them, and you will be able to configure the corresponding function.
4.3.1 PON Certification
Choose “Network Setting”“PON Certification”, the GPON Configuration screen will appear on
the page as shown in Figure 4-2. You are required to enter the GPON Password or GPON SN or
both to pass the ISP authentication before you connect to the Internet. For details, please consult
your ISP.
Figure 4-2
13
TX-6610
1-Port Gigabit GPON Terminal User Guide
GPON Password
Old Password: Displays the factory default password.
New Password: Enter the password provided by your ISP.
Click Save to make the settings take effect.
GPON SN
Old SN: Displays the factory default SN.
New SN: Enter the SN provided by your ISP.
Click Save to make the settings take effect.
4.3.2 VLAN Setting
Choose “Network Setting”“VLAN Setting”, the VLAN Setting screen will appear on the page as
shown in Figure 4-3.
Figure 4-3
VLAN Mode: Select your desired VLAN Mode from the dropdown list.
Control By OLT: OLT (Optical Line Terminal). In this mode, your ISP can remotely
control the Terminal.
VLAN TAG Mode: In this mode, a VLAN tag will be added to an upstream data without it,
and removed from a downstream data.
Transparent Mode: In this mode, all the upstream and downstream data are forwarded
directly.
Remove DownStream VLAN vid: In this mode, all the upstream data can be remotely
controlled by your ISP, and the VLAN tag of all the downstream data will be removed.
DownStream Transparent Mode: In this mode, all the downstream data are forwarded
directly, and all the upstream data can be remotely controlled by your ISP.
Click Save to make the settings take effect.
VLAN Scan: Click the Start VLAN Scan button to search for available VLAN Mode and
VLAN vid.
14
TX-6610
1-Port Gigabit GPON Terminal User Guide
4.3.3 LAN Setting
Choose “Network Setting”“LAN Setting” menu and you will see the LAN screen as shown in
Figure 4-4. You can change the LAN IP address on this page.
Figure 4-4
LAN IP Address and Mask:
IP Address: Enter the Terminal’s local IP Address, then you can access to the
Web-based Utility via the IP Address, the default value is 192.168.1.1.
Mask: Enter the Terminal’s Subnet Mask, the default value is 255.255.255.0.
DHCP Server: These settings allow you to configure the Terminal‘s Dynamic Host
Configuration Protocol (DHCP) server function. The DHCP server is enabled by default for the
Terminal’s Ethernet LAN interface. DHCP service will supply IP settings to computers which
are configured to automatically obtain IP settings that are connected to the Terminal though
the Ethernet port. Keep in mind that if you change the IP address of the Terminal, you must
change the range of IP addresses in the pool used for DHCP on the LAN.
Start IP Address:Enter a value for the DHCP server to start with when issuing IP
addresses. Because the default IP address for the Terminal is 192.168.1.1, the default
Start IP Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater,
but smaller than 192.168.1.254.
End IP Address: Enter a value for the DHCP server to end with when issuing IP
addresses. The End IP Address must be smaller than 192.168.1.254.
Lease Time: The Lease Time is the amount of time in which a network user will be
allowed connection to the Terminal with their current dynamic IP address. Enter the
amount of time, then the user will be “lease” this dynamic IP address. After the dynamic
IP address has expired, the user will be automatically assigned a new dynamic IP
address.
Click Save And Reboot to make the settings take effect.
Note:
If you change the IP Address of LAN, you must use the new IP Address to log in the Terminal.
15
TX-6610
1-Port Gigabit GPON Terminal User Guide
4.4 Management
Choose menu “Management”, and you will see the submenus under the main menu: User
management, Firmware Upgrade, Factory Defaults and Reboot. Click any one of them, and
you will be able to configure the corresponding function. The detailed explanations for each
submenu are provided below.
4.4.1 User Management
Choose menu “Management” “User Management”, and then you can change the factory
default username and password of the Terminal in the next screen as shown in Figure 4-5.
TX-6610 provides two users: admin/admin and user/user. Both can be used to log in the
management page.
Figure 4-5
It is strongly recommended that you should change the factory default username and password of
the Terminal, because all users who try to access the Terminal's Web-based utility will be
prompted for the Terminal's default username and password.
Note:
1) The new username and password cannot exceed 14 characters in length and not include any
spaces. Enter the new Password twice to confirm it.
2) If you use the “user” to log in the Terminal’s management page, only the Status page will you
see.
16
TX-6610
1-Port Gigabit GPON Terminal User Guide
4.4.2 Firmware Upgrade
Choose menu “Management” “Firmware Upgrade”, and then you can update the latest
version of firmware for the Terminal on the following screen.
Figure 4-6
To upgrade the Terminal's firmware, follow the instructions below:
1) Download a most recent firmware upgrade file from our website (www.tp-link.com).
2) Type the path and file name of the update file into the “File Path” field. Or click the Choose
File button to locate the update file.
3) Click the Upgrade button.
4) The Terminal will reboot while the upgrading has been completed.
Note:
1) New firmware versions are posted at http://www.tp-link.com and can be downloaded for free.
There is no need to upgrade the firmware unless the new firmware has a new feature you
want to use. However, when experiencing problems caused by the Terminal rather than the
configuration, you can try to upgrade the firmware.
2) When you upgrade the Terminal's firmware, you may lose its current configurations, so before
upgrading the firmware please write down some of your customized settings to avoid losing
important settings.
3) Do not turn off the Terminal or press the Reset button while the firmware is being upgraded.
Loss of power during the upgrade could damage the Terminal.
4) The firmware version must correspond to the hardware.
5) The upgrade process takes a few moments and the Terminal restarts automatically when the
upgrade is completed.
17
TX-6610
1-Port Gigabit GPON Terminal User Guide
4.4.3 Factory Defaults
Choose menu “Management” “Factory Defaults” and then you can restore the configurations
of the Terminal to its factory defaults on the following screen.
Figure 4-7
Also erase current PON settings: Check this box, the current PON settings will be deleted
when you restore the configurations of the Terminal to its factory defaults.
Click the Restore button to reset all configuration settings to their default values.
• The default Username: admin
• The default Password: admin
Note:
All changed settings will be lost when defaults are restored.
4.4.4 Reboot
Choose menu “Management” “Reboot” and then you can click the Reboot button to reboot the
Terminal via the next screen.
Figure 4-8
18
TX-6610
1-Port Gigabit GPON Terminal User Guide
Appendix A: Specifications
General
Standards and Protocols 802.3, 802.3u, 802.3ab, 802.1p, 802.1q, ITU-T G.984.1, G.984.2,
G.984.3, G.984.4
Safety & Emission FCC, CE
Ports One 10/100/1000M Auto-Negotiation RJ45 port（Auto MDI/MDIX)
One SC/APC (GPON) port
LEDs Power, GPON, LOS, LAN
Network Medium
10Base-T
UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
100Base-TX
UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
1000Base-TX
UTP category 5e, 6 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
GPON Class
C+
G.652 single mode fiber (maximum 20km)
GPON Parameter
Interface SC/APC
Distance 20km
Date Rate
Downstream 2.488Gbps/s
Upstream 1.244Gbps/s
Wavelength Tx 1310nm
Rx 1490nm
Transmitter DFB Laser
Receiver
APD-TIA
Tx Power 0.5dBm～5dBm
Rx Sensitivity ≤-30dBm
System Requirement Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
Win 9x/ ME/ 2000/ XP/ Vista/ 7/8
Physical and Environment
Working Temperature 0℃ ~ 40℃
Working Humidity 10% ~ 90% RH (non-condensing)
Storage Temperature -40℃ ~ 70℃
Storage Humidity 5% ~ 90% RH (non-condensing)
19
TX-6610
1-Port Gigabit GPON Terminal User Guide
Appendix B: Troubleshooting
T1. How to establish a dial-up connection to connect to the Internet?
Run the dialing software such as WinPoet or EnterNet to do the virtual dialing as the following
described.
For Mac OS X
1) Click the Apple icon on the upper left corner of the screen.
2) Go to “System Preferences > Internet & Wireless > Network” and then select Ethernet.
3) In the Configure IPv4 box, select Create PPPoE Service.
4) Type a Service Name to identify your connection.
5) Enter the Username and Password given by your ISP and then click Apply and Connect.
For Windows 7
1) Click Start > Control Panel.
2) Click Network and Sharing Center.
3) Click Set up a new connection or network.
4) Click Connect to the Internet and then click Next.
5) Click Broadband (PPPoE).
6) Enter the Username and Password given by your ISP, and type a Connection name to
identify your connection, and then click Connect.
For Windows XP
1) Click “Start All Programs Accessories Communications New connection wizard”
to launch the wizard. Then click Next.
2) Select Connect to the Internet and then click Next.
3) Select Set up my connection manually and then click Next.
4) Select Connect using a broadband connection that requires user name and password and
then click Next.
5) Type an ISP Name to identify your connection and then click Next.
6) Enter the User name and Password given by your ISP and then click Next.
7) Select Add a shortcut to this connection to my desktop for convenience and then click
Finish.
8) The shortcut icon of this connection will appear on your desktop. Double-click the icon
to run the dialing software and then click Connect.
For Windows 8
1) Move your mouse to the lower right corner and you will see the Search icon in the Popups.
2) Go to Apps, type Control Panel in the search box and press Enter.
3) Go to “Control Panel > Network and Internet > Connect to the Internet”.
20
TX-6610
1-Port Gigabit GPON Terminal User Guide
4) Click Broadband (PPPoE).
5) Enter the User name and Password given by your ISP, and type a Connection name to
identify your connection, and then click Connect.
T2. How do I restore my Terminal to its factory default settings?
Once the Terminal is reset, the current settings will be lost and you will need to reconfigure it. We
strongly suggest you back up the current settings before resetting the Terminal.
With the Terminal powered on, press and hold the RESET button on the rear panel of the Terminal
until all LEDs turn back on momentarily, then release the button.
T3. What can I do if I forget my Terminal’s password?
Reset the Terminal first and then use the default username and password: admin/admin.
T4. How do I change my computer‘s setting to obtain an IP address automatically?
For Mac OS X
1) Click the Apple icon on the upper-left corner of the taskbar.
2) Go to System Preferences > Network.
3) Select Ethernet in the left panel.
4) Under Configure IPv4, select Using DHCP.
5) Click Apply.
For Windows 7/8/8.1
1) Right-click the Network icon (e.g. ) on the system tray and select Open Network and
Sharing Center > Change adapter settings.
2) Right-click the wired network connection (Local Area Connection or Ethernet by default) and
select Properties.
3) Double-click Internet Protocol Version 4 (TCP/IPv4).
4) Select both Obtain an IP address automatically and Obtain DNS server address
automatically, then click OK.
5) Click OK again to save your configuration.
For Windows XP
1) Right-click the Network icon (e.g. ) on the system tray and select Open Network
Connections.
2) Right-click the wired network connection (Local Area Connection by default) and select
Properties.
3) Double-click Internet Protocol (TCP/IP).
4) Select both Obtain an IP address automatically and Obtain DNS server address
automatically, then click OK.
5) Click OK again to save your configuration.
21
TX-6610
1-Port Gigabit GPON Terminal User Guide
T5. What can I do if I cannot access the web management page?
1) Make sure that the computer is properly connected to the Terminal via the Ethernet cable.
2) Make sure that the computer connected to the Terminal is set to obtain an IP address
automatically. Refer to T4 for instructions.
3) Make sure that http://192.168.1.1 is correctly entered, or use another web browser and try
again.
4) Disable then enable the network adapter being used.
5) Restore the Terminal to its factory default settings and reconfigure your Terminal by following
the instructions in this Quick Installation Guide.
T6. What can I do if I cannot access the Internet?
1) Make sure that all cables are connected properly and securely to the Terminal.
2) Check the GPON LED and make sure that it is lit and stable, indicating that the Terminal is
registered with the ISP. If not, make sure that the provided GPON Password and/or GPON
SN are entered correctly in the Network Setting > PON Certification page.
3) Unplug and reconnect the fiber cable to the Terminal. Wait for 2 minutes and try again.
4) Make sure that you follow your ISP's specific instructions to connect to the Internet.
5) Make sure that the computer connected to the Terminal is set to obtain an IP address
automatically. Refer to T4 for instructions.
6) Contact your ISP if the problem still exists.
Note:
For more details about Troubleshooting and Technical Support contact information, please log on
to our Technical Support website:
http://www.tp-link.com/en/support
22