Overview
- What's in this Guide
- Features
Unpacking the OneLINK Bridge AV Interface
A Quick Look at the OneLINK Device
Installing the OneLINK Device
Powering Up the Equipment
Configuration and Administration Tasks
Telnet Serial Command API
Specifications
Troubleshooting
- Operation, Storage, and Care
Compliance Statements and Declarations of Conformity
- OneLINK Bridge AV Interface
- OneLINK HDMI EZCamera Interface Module (EZIM)
Warranty Information
Index

Vaddio RoboSHOT 12 HDBT OneLINK User Manual

Displayed below is the user manual for RoboSHOT 12 HDBT OneLINK by Vaddio which is a product in the Video Conferencing Systems category. This manual has pages.

Related Manuals

Vaddio RoboSHOT 12 HDBT OneLINK HDMI Manual

Integrator's Complete Guide to the

OneLINK Bridge

AV Interface

Document 411-0009-30 Rev C

February 2018

Contents

Overview 1

What's in this Guide 2

Features 2

Unpacking the OneLINK Bridge AV Interface 3

OneLINK Bridge for HDBaseT Cameras 3

OneLINK Bridge For HDBaseT Cameras Used with Codecs 3

OneLINK Bridge For HDMI Cameras 4

OneLINK Bridge For HDMI Cameras Used with Codecs 5

A Quick Look at the OneLINK Device 7

Front Panel of the Receiver 7

Connector Panel of the Receiver 8

Connector Panel of the EZCamera Interface Module (EZIM) 9

Installing the OneLINK Device 10

Don’t Void Your Warranty! 10

Cabling Notes 10

Mounting the OneLINK Device 11

RS-232 Connector Pin-Outs 11

Visual Conventions for Connection Diagrams 11

Connections for HDBaseT Cameras 12

Kits and Systems for HDBaseT Cameras 12

Connecting a Vaddio HDBaseT Camera 13

Connections for HDBaseT Cameras Used with Codecs 14

Kits for HDBaseT Cameras Used with Codecs 14

Connecting a Vaddio HDBaseT Camera and Polycom Codec 15

Connecting a Vaddio HDBaseT Camera and Cisco Codec 17

Connections for HDMI Cameras 22

Kits for HDMI Cameras 22

Connecting a RoboSHOT HDMI Camera 23

Connecting a Polycom EagleEye IV Camera 24

Connecting a Cisco Camera 25

Connecting a Sony or Panasonic HDMI Camera 27

Connections for HDMI Cameras Used with Codecs 29

Kits for HDMI Cameras Used with Codecs 29

Connecting a RoboSHOT HDMI Camera and Polycom Codec 30

Connecting a Polycom EagleEye IV Camera and Polycom Codec 32

Connecting a RoboSHOT HDMI Camera and Cisco Codec 34

Connecting a Cisco Camera and Codec 39

Powering Up the Equipment 46

Configuration and Administration Tasks 46

Compatible Web Browsers 46

Accessing the Web Interface 47

Web Interface Cheat Sheet 48

Configuring Network Settings 49

Assigning a Hostname 50

Specifying Time Zone and NTP Server 50

Managing Access and Passwords 51

Adding Room Information to the Web Interface 51

Configuring Streaming Settings 52

Enabling Phantom Power to Microphones 53

Configuring Audio Settings 54

Muting the Microphones 54

Controlling Volume on Individual Inputs or Outputs 54

Default Microphone Settings 55

Microphone Settings for Environments with Audiences 56

Microphone Adjustments 57

Speaker Adjustments 58

Preventing Audio Feedback 59

Default Audio Matrix 60

Routing Audio 60

Viewing System Information 61

Saving (Exporting) or Restoring (Importing) a Configuration 61

Rebooting the OneLINK Device 62

Restoring Factory Settings 62

Starting a Firmware Update 63

Contacting Vaddio Technical Support and Viewing Diagnostics 64

Telnet Serial Command API 65

link power 65

audio volume 66

audio mute 67

audio route 68

audio crosspoint-gain 69

sleep 70

network settings get 70

network ping 71

system reboot 71

system factory-reset 72

history 73

version 73

help 74

exit 74

Specifications 75

iii

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Troubleshooting 76

Operation, Storage, and Care 78

Compliance Statements and Declarations of Conformity 79

OneLINK Bridge AV Interface 79

FCC Part 15 Compliance 79

ICES-003 Compliance 79

European Compliance 80

OneLINK HDMI EZCamera Interface Module (EZIM) 81

FCC Part 15 Compliance 81

ICES-003 Compliance 81

European Compliance 82

Warranty Information 83

Index 84

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Overview

This guide covers the OneLINK™ Bridge AV Interface, which is available in the following kit configurations

for use with Vaddio or third-party cameras, with or without third-party codecs.

n999-9595-000/001/009, OneLINK Bridge AV interface

n999-9620-000/001/009, OneLINK Bridge AV interface for Polycom EagleEye IV cameras with Polycom

codecs

n999-9630-000/001/009, OneLINK Bridge AV interfacefor Sony and Panasonic cameras

n999-9560-000/001/009, OneLINK Bridge AV interface for RoboSHOT HDMI cameras with Polycom

codecs

n999-9645-000/001/009, OneLINK Bridge AV interface for Vaddio HDBaseT cameras with Polycom

codecs

n999-9660-000/001/009, OneLINK Bridge AV interface for Cisco cameras with Cisco codecs

n999-9670-000/001/009, OneLINK Bridge AV interface for RoboSHOT HDMI cameras with Cisco

codecs

n999-9675-000/001/009, OneLINK Bridge AV interface for Vaddio HDBaseT cameras with Cisco codecs

n999-9690-000/001, OneLINK Bridge AV interface for RoboSHOT HDMI cameras

The OneLINK Bridge AV interfaceis also available as a component of several Vaddio camera systems.

Part number suffixes indicate power cord set types. Those ending in -000 include cord sets for use in North

America; -001 kits include cord sets for use in Europe and the UK; -009 kits include cord sets for use in

Australia and New Zealand.

If the camera extension is sold for use with an HDMI camera, it is shipped with a OneLINK EZCamera

Interface Module (EZIM).

What's in this Guide

This guide provides information about:

nUnpacking

nPhysical features

nInstallation

nConfiguration and system administration

nTelnet API for third-party control

nSpecifications

nTroubleshooting and maintenance

nWarranty

For your convenience, most of this information is also available in smaller, limited-purpose manuals:

nInstallation Guide for the OneLINK Bridge AV Interface – Unpacking, physical features,

installation, and initial power-on.

nConfiguration and Administration Guide for the OneLINK Bridge AV Interface – Physical

features, web interface for device configuration and system administration, and troubleshooting.

Download manuals, dimensional drawings, and other information from support.vaddio.com.

Features

nConverts any conference room to a BYOD environment, delivering a USB stream for soft-conferencing

clients

nIncorporates Vaddio’s market-leading AV Bridge functionality, connecting professional AV equipment to

PC applications via USB 3.0 media stream

nVideo with audio: Simultaneous uncompressed USB 3.0, HDMI 1.4b, and 3Gb/s HD-SDI; passes IP

stream if available from source

nTwo balanced audio inputs, line level or mic level; two balanced audio outputs, line level

nControl via web interface or Telnet; passes web-based, Telnet, and RS-232 serial control to connected

devices

nSimple, clutter-free camera installation – power, control, video, and streaming over one Cat-5e or better

cable

nExtends installation distance for HDMI and HDBaseT™ cameras up to 100 m (328 ft.)

nCompatible with Vaddio HDBaseT cameras – no EZCamera Interface Module (EZIM) needed

nCompatible with Vaddio and other HDMI cameras

nAvailable in system configurations with Vaddio cameras

nKits available for use with Polycom and Cisco codecs and other HDMI cameras

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Unpacking the OneLINK Bridge AV Interface

Make sure you received all the items you expected. Here are the packing lists for the OneLINK Bridge kits.

Every OneLINK device ships with a power supply and at least one AC cord set. The last three digits of the

kit part number contain the regional code that specifies which cord set(s). For most OneLINK kits, the part

numbers follow this convention:

nKits with part numbers ending in -000 include one AC cord set for North America.

nKits with part numbers ending in -001 include two AC cord sets, one for Europe and one for the UK.

nKits with part numbers ending in -009 include one AC cord set for Australia and New Zealand.

OneLINK Bridge for HDBaseT Cameras

OneLINK Bridge AV Interface for Vaddio HDBaseT Cameras, 999-9595-000/001/009

Camera not included.

nOneLINK Bridge AV interface

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nEZCamera RS-232 control adapter (998-1001-232)

nQuick-Start Guide 411-0009-01

OneLINK Bridge For HDBaseT Cameras

Used with Codecs

OneLINK Bridge for Vaddio HDBaseT Cameras with Polycom Codecs, 999-9645-000/001/009

Camera and codec not included.

nOneLINK Bridge AV interface

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm (qty. 4)

nFan-out cable, codec side, 2 ft. (0.6 m)

nEZCamera RS-232 control adapter 998-1001-232

nQuick-Start Guide 411-0009-01

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK Bridge for Vaddio HDBaseT Cameras with Cisco Codecs, 999-9675-000/001/009

Camera and codec not included.

Note

If connecting to a Cisco SX20 codec, you will need to provide

a Cisco split cable, Cisco part number CAB-PHD4XS2-

SPLIT.

nOneLINK Bridge AV interface

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm (qty. 4)

nHDMI cable, 3 ft. (0.9 m)

nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)

nCat-5e patch cable, 3 ft. (0.9 m)

nEZCamera RS-232 control adapter 998-1002-232

nQuick-Start Guide 411-0009-01

OneLINK Bridge For HDMI Cameras

OneLINK Bridge for RoboSHOT HDMI Cameras, 999-9690-000/001/009

Camera not included.

nOneLINK Bridge AV interface

nOneLINK EZCamera Interface Module (EZIM) with

mounting screws

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nHDMI cable, 1 ft. (0.3 m)

nCat-5e patch cable, 1 ft. (0.3 m), qty. 2

nEZCamera RS-232 control adapter

nQuick-Start Guide 411-0009-02

OneLINK Bridge for Sony and Panasonic Cameras, 999-9630-000/001/009

Camera not included.

nOneLINK Bridge AV interface

nOneLINK EZCamera Interface Module (EZIM)

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nWall mount with mounting hardware for Sony and

Panasonic cameras

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nPower cable EIAJ-04 to 3x6.3mm, 1 ft. (0.3 m)

nHDMI cable, 1 ft. (0.3 m)

nRJ-45 to 8-pin mini-DIN cable, 1 ft. (0.3 m)

nCat-5e patch cable, 1 ft. (0.3 m)

nQuick-Start Guide 411-0009-02

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK Bridge For HDMI Cameras Used with Codecs

OneLINK Bridge for Polycom Cameras with Polycom Codecs, 999-9620-000/001/009

Camera and codec not included.

nOneLINK Bridge AV Interface

nOneLINK EZCamera Interface Module (EZIM)

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nWall mount with mounting hardware for Polycom codec

and camera

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nFan-out cable, EZIM side, 1 ft. (0.3 m)

nFan-out cable, codec side, 2 ft. (0.6 m)

nEZCamera RS-232 control adapter 998-1001-232

nQuick-Start Guide 411-0009-02

OneLINK Bridge for RoboSHOT HDMI with Polycom Codecs, 999-9640-000/001/009

Camera and codec not included.

nOneLINK Bridge AV interface

nOneLINK EZCamera Interface Module (EZIM)

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nFan-out cable, codec side, 2 ft. (0.6 m)

nCat-5e patch cable, 1 ft. (0.3 m), qty. 2

nHDMI cable, 1 ft. (0.3 m)

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nQuick-Start Guide 411-0009-02

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK Bridge for Cisco Cameras with Cisco Codecs, 999-9660-000/001/009

Camera and codec not included.

Note

If connecting to a Cisco SX20 codec, you will need to provide

a Cisco split cable, Cisco part number CAB-PHD4XS2-

SPLIT. This cable is also required when connecting to a Cisco

Precision 40 or Precision HD 1080p2.5x camera; you will need

two of them if connecting one of these cameras and an SX20

codec.

nOneLINK Bridge AV Interface

nOneLINK EZCamera Interface Module (EZIM) with

mounting screws

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nWall mount with mounting hardware for Cisco codec and

camera

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nPower cable EIAJ-04 to 5.5x2.1 mm, 1 ft. (0.3 m)

nHDMI cable, 1 ft. (0.3 m)

nHDMI cable, 3 ft. (0.9 m)

nCustom-pinout Cat-5e cable for Cisco cameras, 1 ft. (0.3 m)

nCustom-pinout Cat-5e cable for Cisco SX20, 3 ft. (0.9 m)

nCat-5e patch cable, 1 ft. (0.3 m)

nCat-5e patch cable, 3 ft. (0.9 m)

nEZCamera RS-232 control adapter 998-1002-232

nQuick-Start Guide 411-0009-02

OneLINK Bridge for RoboSHOT HDMI with Cisco Codecs, 999-9670-000

Camera and codec not included.

Note

If connecting to a Cisco SX20 codec, you will need to provide

a Cisco split cable, Cisco part number CAB-PHD4XS2-

SPLIT.

nOneLINK Bridge AV Interface

nOneLINK EZCamera Interface Module (EZIM) with

mounting screws

nPower supply, 48 VDC/1.36 A, with AC cord set(s)

nUSB 3.0 A to B cable, 6 ft. (1.8 m)

n3-position Phoenix connector plug, 3.5 mm, qty. 4

nPower cable EIAJ-04 to EIAJ-04, 1 ft. (0.3 m)

nHDMI cable, 1 ft. (0.3 m)

nHDMI cable, 3 ft (0.9 m)

nCustom-pinout Cat-5e cable for Cisco, 3 ft. (0.9 m)

nCat-5e patch cable, 1 ft. (0.3 m), qty. 2

nCat-5e patch cable, 3 ft. (0.9 m)

nEZCamera RS-232 control adapter 998-1002-232

nQuick-Start Guide

Integrator's Complete Guide to the OneLINK Bridge AV Interface

A Quick Look at the OneLINK Device

This section covers the physical features of the OneLINK Bridge AV interface.

All OneLINK kits include a receiver, which is typically co-located with other equipment, up to 328 ft (100 m)

away from the camera. OneLINK kits for use with HDMI cameras also include an EZCamera Interface

Module (EZIM) HDBaseT converter, which is mounted adjacent to the camera.

Front Panel of the Receiver

nUSB indicator – Illuminates when a USB stream is present.

nNetwork indicator – Illuminates when connected to the IP network.

nSource indicator – Illuminates when a video input is detected.

nOneLINK indicator – Illuminates when the OneLINK Bridge detects a connection to an HDBaseT

device or to the OneLINK EZIM.

nDisplay IP and MAC Address button (illuminated blue) – Outputs the OneLINK Bridge IP and MAC

addresses as an overlay on the HDMI, HD-SDI, and USB video outputs.

nPower System Reset button (illuminated red) – reboots the OneLINK Bridge without affecting the

connected camera.

Note

The OneLINK device does not control the camera; it passes IP and RS-232 traffic to and from the camera.

Use the camera's IP address to access the camera's web interface. The OneLINK device's IP address

only provides access to the OneLINK device, not to the connected camera.

Note

To discover the attached Vaddio camera's IP address, point the IR Remote Commander at the camera and

press the Data Screen button. The camera's IP and MAC addresses are displayed on the connected HDMI

video output.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connector Panel of the Receiver

From the left:

nPower input jack – Use the supplied 48VDC, 1.36A power supply.

nOneLINK interface port – Connect a Cat-5e (or better) cable to the EZIM, or to the camera if your

OneLINK kit or system did not include an EZIM. This bidirectional connection carries video, audio (if

available), network connectivity including H.264 IP streaming from the camera (if available), RS-232

control, and 12 VDC power.

nHDMI output – HDMI output to a connected display.

nUSB 3.0 – Uncompressed video output with PCM audio for conferencing applications

nHD-SDI – Video output from the camera

nNetwork port – H.264 IP streaming (if available from the camera), web interface access, and third-

party IP control via Telnet API.

nRS-232 port – Connect to a camera controller.

nAudio I/O Line Out 1 and Line Out 2 – Far-end audio from conferencing application or as configured

in the audio matrix

nAudio I/O Mic/Line In 1 and Mic/Line In 2 – Microphone or other audio inputs

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connector Panel of the EZCamera Interface Module (EZIM)

If the OneLINK device is used with an HDMI camera, the EZIM is required.

From the left:

nPower output jack – Supplies power to the camera. The kit you purchased includes the appropriate

cable to connect your camera's power input to this jack.

nNetwork port – Provides network connectivity to the camera for H.264 IP streaming (if available from

the camera), web interface access, and third-party control via Telnet API. Connect to the camera's

network port.

nRS-232 port – Provides RS-232 connectivity to the camera, for third-party control. The kit you

purchased may include a cable and/or an RS-232 adapter to connect to the camera's RS-232 port.

nHDMI input – Receives HDMI video from the camera. Connect to the camera's HDMI output.

nOneLINK port – Single-cable connection to the OneLINK receiver. This bidirectional connection

carries all video, power, and control.

Note

Cat-6 or Cat-7 cabling may provide better performance in noisier RF or EMF environments. When in doubt,

use shielded Cat-6 cable. Cable distance between the EZIM and the OneLINK device is a maximum of 328

feet (100 m).

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Installing the OneLINK Device

This section covers:

nThings to know before you start the installation

nBasic connection examples

Rack mounting brackets are available for the OneLINK receiver.

Don’t Void Your Warranty!

Caution

Use only the power supply included with this product. Using a different one will void the warranty, and

could create unsafe operating conditions or damage the product.

Do not connect the OneLINK power supply to a camera. It does not provide the correct voltage for Vaddio

cameras, and will damage the camera and void the camera's warranty.

This product is for indoor use only. Do not install it outdoors or in a humid environment. Do not allow it to

come into contact with any liquid.

Do not install or operate this product if it has been dropped, damaged, or exposed to liquids. If any of these

things happen, return it to Vaddio for safety and functional testing.

All information about this product is available for download at www.vaddio.com/support – no cost, no

registration required.

Cabling Notes

Cat-6 or Cat-7 cabling may provide better performance in noisier RF or EMF environments. When in doubt,

use shielded Cat-6 cable. Cable distance between the EZIM and the OneLINK device is a maximum of 328

feet (100 m).

Note

Use standard RJ-45 connectors and a good crimping tool. Do not use pass-through RJ-45

connectors. Poorly crimped connectors can damage the connectors on the product, cause

intermittent connections, and degrade signal quality. Test cable pin-outs and continuity

before connecting them.

Intact – Contact fingers will make reliable

contact with the cable connector

Damaged – Some contact fingers are bent

and will NOT make reliable contact with the

cable connector

Pro Tip

To prevent tragic mishaps, label both ends of every cable.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Mounting the OneLINK Device

If you are installing the OneLINK device with a OneLINK EZIM, mount the EZIM with or near the camera.

Most Vaddio Thin Profile Wall Mounts include two mounting holes to attach the EZIM to the underside of

the mount using two 6-32 screws. Connect all required cables during camera installation.

Rack and under-table mounting kits are available for the receiver. Follow the mounting instructions supplied

with the kit.

RS-232 Connector Pin-Outs

OneLINK Receiver - RS-232 Control Port

1. Unused

2. Unused

3. Unused

4. Unused

5. Unused

6. GND – green

7. RX (from TX of controller) – brown/white

8. TX (to RX of controller) – brown

OneLINK EZIM - RS-232 Control Port

1. Unused

2. Unused

3. Unused

4. IR GND

5. IR (non-mod)

6. GND – green

7. TX (to RX of camera) – brown/white

8. RX (from TX of camera) – brown

Note

Vaddio recommends adhering to the 568B cabling standard for Cat-5 cabling.

Visual Conventions for Connection Diagrams

The following sections provide representative connection diagrams for the various OneLINK kit and system

configurations available. All diagrams in this guide use these visual conventions for connection type.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connections for HDBaseT Cameras

In this configuration, the OneLINK Bridge extends network connectivity, power, and control to an

HDBaseT camera, and brings HDMI video from the camera to a display. The camera can optionally be

controlled by a camera controller on an RS-232 serial connection to the OneLINK Bridge or over the

network, depending on the controller. The OneLINK Bridge also provides connections for microphones and

speakers, and can originate a USB stream to bridge the non-USB camera and audio equipment into a USB-

based conferencing application.

If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming

resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including

resolution) are configured on the camera, not the OneLINK device.

Kits and Systems for HDBaseT Cameras

This block diagram applies to:

nOneLINK Bridge for Vaddio HDBT Cameras, 999-9595-000/001/009 – compatible with all Vaddio

HDBaseT cameras.

nRoboSHOT 12 HDBT OneLINK Bridge System, 999-9960-200/201/209

nRoboSHOT 30 HDBT OneLINK Bridge System, 999-9963-200/200W/201/201W/209/209W

nRoboSHOT 20 UHD OneLINK Bridge System, 999-9950-200/200W/201/201W/209/209W

nDocCAM 20 HDBT OneLINK Bridge System, 999-9968-300/301/309

nFuture systems consisting of a Vaddio HDBaseT camera and a OneLINK Bridge AV interface

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Vaddio HDBaseT Camera

999-9595-000/001/009

In this diagram, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT 12

HDBT camera, and brings HDMI video from the camera to a display. The OneLINK Bridge also provides

audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Items in this diagram:

nOneLINK BridgeAV interface

nRoboSHOT 12 HDBT camera (not included in kit 999-9595-000/001/009)

nHDMI display and HDMI cable (not included)

nLaptop using soft conferencing client (not included)

nUSB 3.0 cable to laptop

nAudio cables (not included) terminated with supplied connectors

nConnections to microphones and speakers (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOT HDBT Camera

Other Vaddio HDBaseT cameras connect in the same way.

Camera Configuration

You can configure the following settings on your Vaddio HDBaseT camera:

nHDMI output resolution: Depending on the camera, set this using the rotary switch on the back of the

camera or the virtual rotary switch on DIP Switches tab of the System page.

nIP streaming: Streaming page. Settings include Enable/disable, streaming quality, and streaming

resolution.

Point the remote at the camera and press the Data Screen button to see the camera's IP address on the

connected display.

No additional configuration is required.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connections for HDBaseT Cameras Used with Codecs

In this configuration, the OneLINK HDMI extends network connectivity, power, and control to an HDBaseT

camera, and brings HDMI video from the camera to a connected codec. The codec may be connected to

the OneLINK device directly via RS-232, or they may communicate over the IP network, depending on the

codec. The OneLINK Bridge can originate a USB stream to bridge the camera, codec, and codec-

connected audio equipment into a USB-based conferencing application.

If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming

resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including

resolution) are configured on the camera, not the OneLINK device.

Kits for HDBaseT Cameras Used with Codecs

This block diagram applies to:

nOneLINK Bridge for Vaddio HDBT Cameras with Polycom Codecs, 999-9645-000/001/009 –

compatible with all Vaddio HDBT cameras and with Polycom RealPresence Group Series codecs.

nOneLINK Bridge for Vaddio HDBT Cameras with Cisco Codecs, 999-9675-000/001/009 – compatible

with all Vaddio HDBT cameras and with Cisco C20, C40, C60, SX20, and SX80 codecs.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Vaddio HDBaseT Camera and Polycom Codec

999-9645-000/001/009

In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT

12 HDBT camera, and connects the camera to a Polycom codec. The OneLINK Bridge also provides audio

connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Other Vaddio HDBaseT cameras would be connected in exactly the same way.

Items in these diagrams:

nOneLINK Bridge AV interface

nPower supply with AC cord set

nCodec-side fan-out cable

nRoboSHOT 12 HDBT camera (not included)

nPolycom RealPresence Group Series codec (not included)

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOT HDBT Camera and Polycom RealPresence Group 310 Codec

The Group 500 codec looks very similar and connects in the same way.

Other Vaddio HDBaseT cameras connect in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDBT Camera and Polycom RealPresence Group 700 Codec

Other Vaddio HDBaseT cameras connect in the same way.

Hardware Note: IR Forwarding

Although the OneLINK Bridge does not support IR forwarding, the two unterminated wires of the fan-out

cable can be terminated and connected to an IR emitter (repeater).

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

Camera Configuration

Point the remote at the camera and press the Data Screen button to see the camera's IP address on the

connected display.

You can configure the following settings on your Vaddio HDBaseT camera:

nHDMI output resolution: Depending on the camera, set this using the rotary switch on the back of the

camera or the virtual rotary switch on DIP Switches tab of the System page.

nIP streaming: Streaming page. Settings include Enable/disable, streaming quality, and streaming

resolution.

nCodec Control Mode: Soft DIP on the DIP Switches tab of the System page.

nIR: ON (default). DIP switch 3 on the back of RoboSHOT 20 UHD or RoboSHOT HDBT cameras, soft

DIP 3 on the DIP Switches tab of the System page for DocCAM 20 HDBT.

Note

Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware

update to add this capability.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Vaddio HDBaseT Camera and Cisco Codec

999-9675-000/001/009

In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT

12 HDBT camera, and connects the camera to a Cisco codec. The OneLINK Bridge also provides audio

connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Other Vaddio HDBaseT cameras would be connected in exactly the same way.

Items in these diagrams:

nOneLINK Bridge AV interface

nPower supply and AC cord set

nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)

nCisco split cable CAB-PHD4XS2-SPLIT(not included; required for SX20 codec)

nCodec-side null modem cable (used with split cable on SX20 codec)

nRoboSHOT 12 HDBT camera (not included)

nCisco codec (not included)

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOT HDBT Camera and Cisco C20 Codec

Other Vaddio HDBaseT cameras connect in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDBT Camera and Cisco C60 Codec

The C40 codec looks very similar and connects in the same way.

Other Vaddio HDBaseT cameras connect in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDBT Camera and Cisco SX20 Codec

Other Vaddio HDBaseT cameras connect in the same way.

Note

If connecting to a Cisco SX20 codec, you will need to provide a Cisco split cable, Cisco part number CAB-

PHD4XS2-SPLIT.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDBT Camera and Cisco SX80 Codec

Other Vaddio HDBaseT cameras connect in the same way.

Hardware Note: RS-232 Connections

For RS-232 connections to Cisco gear using DE-9 connectors, use the 998-1002-232 RJ-45 to DE-9

adapter. Its wiring differs from the 998-1001-232 adapter shipped with many Vaddio products.

For RS-232 connections to Cisco gear using the Cisco split cable, use the appropriate null-modem cable to

the RJ-45 side of the split cable. Connect the null-modem cable as indicated on the cable labels.

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK Device Configuration

After installation is complete and the OneLINK device and camera are operational, you will need to change

the AEC reference if you made the audio connections as shown in these diagrams.

On the Audio page of the OneLINK Bridge web interface, set Master Output/AEC Reference to Output 2 if

using Line Out 2 for the speaker connection.

Camera Configuration

Point the remote at the camera and press the Data Screen button to see the camera's IP address on the

connected display.

You can configure the following settings on your Vaddio HDBaseT camera:

nHDMI output resolution: Depending on the camera, set this using the rotary switch on the back of the

camera or the virtual rotary switch on DIP Switches tab of the System page.

nIP streaming: Streaming page. Settings include Enable/disable, streaming quality, and streaming

resolution.

nCodec Control Mode: Soft DIP on the DIP Switches tab of the System page.

nIR: ON (default). DIP switch 3 on the back of RoboSHOT 20 UHD or RoboSHOT HDBT cameras, soft

DIP 3 on the DIP Switches tab of the System page for DocCAM 20 HDBT.

Note

Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware

update to add this capability.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connections for HDMI Cameras

In this configuration, the OneLINK Bridge extends network connectivity, power, and control to an HDMI

camera, and brings HDMI video from the camera to a display. The camera can optionally be controlled by a

camera controller on an RS-232 serial connection to the OneLINK Bridge or over the network, depending on

the controller. The OneLINK Bridge also provides connections for microphones and speakers, and can

originate a USB stream to bridge the non-USB camera and audio equipment into a USB-based

conferencing application.

If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming

resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including

resolution) are configured on the camera, not the OneLINK device.

Kits for HDMI Cameras

This block diagram applies to:

nOneLINK Bridge AV interface for Polycom cameras with Polycom Codecs, 999-9620-000/001/009,

when used without a codec – compatible with Polycom EagleEye IV camera.

nOneLINK Bridge AV Interface for Sony and Panasonic Cameras, 999-9630-000/001/009 – compatible

with Panasonic HE-series, Sony EVI-D series, and Sony BRC-H series cameras.

nOneLINK Bridge AV interface for Cisco Cameras with Cisco Codecs, 999-9660-000/001/009, when

used without a codec – compatible with Cisco Precision series cameras.

nOneLINK Bridge AV Interface for RoboSHOT HDMICameras, 999-9690-000/001/009

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a RoboSHOT HDMI Camera

999-9690-000/001/009

In this diagram, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT

HDMI camera, and brings camera video to the connected HDMI display. The OneLINK Bridge also

provides audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-

based conferencing application.

Items in this diagram:

nOneLINK Bridge AV interface and OneLINK EZIM

nOneLINK power supply and AC cord set

nRoboSHOT 12 HDMI camera (not included)

nPower cable, HDMI cable, and Cat-5e cables from the OneLINK EZIM to the camera

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

Camera Configuration

Set HDMI output resolution using the rotary switch on the back of the camera. No additional configuration

is required; if desired, additional configuration is available via the camera's web interface. Point the remote

at the camera and press the Data Screen button to see the camera's IP address on the connected HDMI

display.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Polycom EagleEye IV Camera

999-9620-000/001/009

In this diagram, the OneLINK Bridge extends network connectivity, power, and control to a Polycom

EagleEye IV camera, and brings HDMI video from the camera to a display. The OneLINK Bridge also

provides audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-

based conferencing application.

Items in this diagram:

nOneLINK Bridge AV interface and OneLINK EZIM

nPower supply and AC cord set

nCamera-side fan-out cable

nPolycom EagleEye IV camera (not included)

nHDMI display and cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Cisco Camera

999-9660-000/001/009

In these diagrams, the OneLINK Bridge extends power and control to a Cisco camera, and brings HDMI

video from the camera to a display. The OneLINK Bridge also provides audio connections, and can

originate a USB stream to bridge non-USB equipment into a USB-based conferencing application.

nOneLINK BridgeAV interface and OneLINK EZIM

nCamera-side fan-out cable (not included; used with Precision 40 and Precision HD 1080p2.5x)

nCisco camera (not included)

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

Cisco Precision 40 or Precision HD Series Camera

Note

If connecting to a Cisco Precision 40 or Precision HD 1080p2.5x camera, you will need to provide a Cisco

split cable, Cisco part number CAB-PHD4XS2-SPLIT.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Cisco Precision 60 Camera

Hardware Note: RS-232 Connections

For RS-232 connections to Cisco cameras, use the appropriate null-modem cable. Connect it as indicated

on the cable labels. This cable is used with the Cisco split cable CAB-PHD4XS2-SPLIT for some

cameras.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Sony or Panasonic HDMI Camera

999-9630-000/001/009

In these diagrams, the OneLINK Bridge extends power and control to a Sony or Panasonic HDMI camera,

and brings video from the camera to a display. The OneLINK Bridge also provides audio connections, and

can originate a USB stream to bridge non-USB equipment into a USB-based conferencing application.

Items in this diagram:

nOneLINK Bridge AV interface and OneLINK EZIM

nPower supply and AC cord set

nCamera with cables (not included)

nHDMI display and cable (not included)

nLaptop with soft conferencing client (not included)

Panasonic AW-HE130 Camera

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Sony SRG300 Camera

The SRG120 camera's connector panel looks very similar, and connects in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connections for HDMI Cameras Used with Codecs

In this configuration, the OneLINK HDMI extends network connectivity, power, and control to an HDMI

camera, and brings HDMI video from the camera to a connected codec. The codec may be connected to

the OneLINK device directly via RS-232, or they may communicate over the IP network, depending on the

codec. The OneLINK Bridge can originate a USB stream to bridge the camera, codec, and codec-

connected audio equipment into a USB-based conferencing application.

If an IP stream is available from the camera, the OneLINK device passes it to the network. IP streaming

resolutions up to 2160p/30 are supported. HDMI output resolution and streaming parameters (including

resolution) are configured on the camera, not the OneLINK device.

Kits for HDMI Cameras Used with Codecs

This block diagram applies to:

nOneLINK Bridge for Polycom Cameras with Polycom Codecs, 999-9620-000/001/009 – compatible

with Polycom EagleEye IV camera and Polycom RealPresence Group Series codecs.

nOneLINK Bridge for RoboSHOT HDMICameras with Polycom Codecs, 999-9640-000/001/009 –

compatible with RoboSHOT HDMI HDMI cameras and Polycom RealPresence Group Series codecs.

nOneLINK Bridge for Cisco Cameras with Cisco Codecs, 999-9660-000/001/009 – compatible with

Cisco Precision series cameras and Cisco C20, C40, C60, SX20, and SX80 codecs.

nOneLINK Bridge for RoboSHOT HDMI Cameras with Cisco Codecs, 999-9670-000/001/009 –

compatible with RoboSHOT HDMI cameras and with Cisco C20, C40, C60, SX20, and SX80 codecs.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a RoboSHOT HDMI Camera and Polycom Codec

999-9640-000/001/009

In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT

12 or 30 HDMI camera, and connects the camera to a Polycom codec. The OneLINK Bridge also provides

audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Items in these diagrams:

nOneLINK Bridge AV interface and OneLINK EZIM

nPower supply with AC cord set

nRoboSHOT 12 HDMI camera (not included)

nPolycom RealPresence Group Series codec (not included)

nCodec-side fan-out cable

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOT HDMI Camera and Polycom RealPresence Group 310 Codec

The Group 500 codec looks very similar and connects in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDMI Camera and Polycom RealPresence Group 700 Codec

Hardware Note: IR Forwarding

Although the OneLINK Bridge does not support IR forwarding, the two unterminated wires of the fan-out

cable can be terminated and connected to an IR emitter (repeater).

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

Camera Configuration

Set HDMI resolution and IR forwarding using the switches on the back of the camera:

nSet HDMI output resolution using the rotary switch.

nSet DIP switch 3 DOWN to enable IR forwarding.

Codec Control Mode and other configuration settings are available from the camera's web interface. Point

the remote at the camera and press the Data Screen button to see the camera's IP address on the

connected HDMI display.

Enable Codec Control Mode on the DIP Switches tab of the System page.

Note

Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware

update to add this capability.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Polycom EagleEye IV Camera and Polycom Codec

999-9620-000/001/009

In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a Polycom

EagleEye IV camera, and connects the camera to a Polycom codec. The OneLINK Bridge also provides

audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Items in these diagrams:

nOneLINK Bridge AV interface and OneLINK EZIM

nPower supply with AC cord set

nPolycom EagleEye IV camera (not included)

nPolycom RealPresence Group Series codec (not included)

nCodec-side fan-out cable

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

Polycom EagleEye IV Camera and Polycom RealPresence Group 310 Codec

The Group 500 codec looks very similar and connects in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Polycom EagleEye IV Camera and Polycom RealPresence Group 700 Codec

Hardware Note: IR Forwarding

Although the OneLINK Bridge does not support IR forwarding, the two unterminated wires of the fan-out

cable can be terminated and connected to an IR emitter (repeater).

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a RoboSHOT HDMI Camera and Cisco Codec

999-9670-000/001/009

In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a RoboSHOT

12 or 30 HDMI camera, and connects the camera to a Cisco codec. The OneLINK Bridge also provides

audio connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Items in these diagrams:

nOneLINK Bridge AV interface and OneLINK EZIM

nPower supply and AC cord set

nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)

nCisco split cable CAB-PHD4XS2-SPLIT (not included; required for SX20 codec)

nCodec-side null modem cable (used with split cable on SX20 codec)

nRoboSHOT 12 HDMI camera (not included)

nCisco codec (not included)

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

RoboSHOT HDMI Camera and Cisco C20 Codec

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDMI Camera and Cisco C60 Codec

The C40 codec looks very similar and connects in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDMI Camera and Cisco SX20 Codec

Note

If connecting to a Cisco SX20 codec, you will need to provide a Cisco split cable, Cisco part number CAB-

PHD4XS2-SPLIT.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

RoboSHOT HDMI Camera and Cisco SX80 Codec

Hardware Note: RS-232 Connections

For RS-232 connections to Cisco gear using DE-9 connectors, use the 998-1002-232 RJ-45 to DE-9

adapter. Its wiring differs from the 998-1001-232 adapter shipped with many Vaddio products.

For RS-232 connections to Cisco gear using the Cisco split cable, use the appropriate null-modem cable to

the RJ-45 side of the split cable. Connect the null-modem cable as indicated on the cable labels.

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK Device Configuration

After installation is complete and the OneLINK device and camera are operational, you will need to change

the AEC reference if you made the audio connections as shown in these diagrams.

On the Audio page of the OneLINK Bridge web interface, set Master Output/AEC Reference to Output 2 if

using Line Out 2 for the speaker connection.

Camera Configuration

Set HDMI resolution and IR forwarding using the switches on the back of the camera:

nSet HDMI output resolution using the rotary switch.

nSet DIP switch 3 DOWN to enable IR forwarding.

Codec Control Mode and other configuration settings are available from the camera's web interface. Point

the remote at the camera and press the Data Screen button to see the camera's IP address on the

connected HDMI display.

Enable Codec Control Mode on the DIP Switches tab of the System page.

Note

Codec Control Mode was added to Vaddio cameras in early 2018. Your camera may require a firmware

update to add this capability.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Connecting a Cisco Camera and Codec

999-9660-000/001/009

In these diagrams, the OneLINK Bridge extends network connectivity, power, and control to a Cisco

camera, and connects the camera to a Cisco codec. The OneLINK Bridge also provides audio

connections, and can originate a USB stream to bridge non-USB equipment into a USB-based

conferencing application.

Items in these diagrams:

nOneLINK BridgeAV interface and OneLINK EZIM

nCisco split cable CAB-PHD4XS2-SPLIT (not included; required for SX20 codec and for Precision 40

and Precision HD 1080p2.5x cameras)

nCamera-side null modem cable (used on all supported Cisco cameras)

nCodec-side null modem cable (used with Cisco split cable on SX20 codec)

nRS-232 adapter 998-1002-232 (used with standard Cat-5 cable on C20, C60. and SX80 codecs)

nCisco camera (not included)

nCisco codec (not included)

nHDMI display and HDMI cable (not included)

nLaptop with soft conferencing client (not included)

nCat-5e cables for OneLINK and network connections (not included)

Note

If connecting to a Cisco SX20 codec, you will need to provide a Cisco split cable, Cisco part number CAB-

PHD4XS2-SPLIT. This cable is also required when connecting to a Cisco Precision 40 or Precision HD

1080p2.5x camera; you will need two of them if connecting one of these cameras and an SX20 codec.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Cisco Precision 40 or Precision HD Series Camera and Cisco C20 Codec

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Cisco Precision 40 or Precision HD Series Camera and Cisco C60 Codec

The C40 codec looks very similar and connects in the same way.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Cisco Precision 40 or Precision HD Series Camera and Cisco SX20 Codec

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Cisco Precision 40 or Precision HD Series Camera and Cisco SX80 Codec

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Cisco Precision 60 Camera and Cisco SX80 Codec

Hardware Note: RS-232 Connections

For RS-232 connections to Cisco gear using DE-9 connectors, use the 998-1002-232 RJ-45 to DE-9

adapter. Its wiring differs from the 998-1001-232 adapter shipped with many Vaddio products.

For RS-232 connections to Cisco gear using the Cisco split cable, use the appropriate null-modem cable to

the RJ-45 side of the split cable. Connect the null-modem cable as indicated on the cable labels.

Hardware Note: Connection and Configuration Changes

After connecting or configuring the equipment, reboot the OneLINK device, camera, and codec. Note that

rebooting the OneLINK device does not affect the camera and codec; they must be rebooted separately.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK Device Configuration

After installation is complete and the OneLINK device and camera are operational, you will need to change

the AEC reference if you made the audio connections as shown in these diagrams.

On the Audio page of the OneLINK Bridge web interface, set Master Output/AEC Reference to Output 2 if

using Line Out 2 for the speaker connection.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Powering Up the Equipment

Power up the connected equipment that is not powered by the OneLINK device (such as displays and third-

party control devices), then connect power to the OneLINK device. The connected camera and the

OneLINK device power up together.

Configuration and Administration Tasks

The OneLINK Bridge AV interface provides a web interface to allow configuration and administration using

a browser.

The web interface allows password-protected access to tasks such as setting passwords, changing the IP

address, viewing diagnostics, and installing firmware updates.

Note

The OneLINK device is not a camera control device. To configure or operate the camera, use the camera's

web interface. Refer to the camera's documentation for details.

Note

The connected camera is configured separately from the OneLINK device. Changes to the OneLINK

device's configuration do not affect the configuration of the camera or other connected equipment. If you

need to change the way the camera is configured, log in to the camera's web interface.

Compatible Web Browsers

We have tested this product with these web browsers:

nChrome®

nFirefox®

nMicrosoft® Internet Explorer®

nSafari®

We test using the browser version available from the vendor at that time. Older versions of these browsers

are likely to work, and other browsers may also work.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Accessing the Web Interface

To get the IP address:

Press the button labeled Display IP and MAC Address, on the front of the unit. The information is overlaid

on the HDMI, HD-SDI, and USB video outputs.

The OneLINK device will use the default address of 169.254.10.1 if no DHCP server is available. In this

situation, you will need to connect a computer to the OneLINK device's network port and configure network

settings. Depending on the computer, you may need a crossover cable.

To access the web interface:

Enter the IP address or hostname in your browser's address bar. If you use the hostname, you may need to

enter http:// as a prefix to keep the browser from treating it as a search query.

The login page opens. The username admin and the default password is password.

After you log in, the System page opens.

Note

For best security, Vaddio strongly recommends changing the default password. Using default passwords

leaves the product vulnerable to tampering. See Managing Access and Passwords.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Web Interface Cheat Sheet

You must log in to access the pages for all system administration tasks.

Note

The OneLINK device's web interface does not provide access to the connected camera. To configure the

camera, use the camera's web interface, which is at a separate IP address.

What do you need to do? Go to this page

Mute the connected microphone(s) Mute button on all pages

Adjust audio inputs and outputs Audio

Allow conferencing applications to control the audio Streaming

Enable or disable USB streaming Streaming

Find the current firmware version System

Change the Admin password Security

Reboot, restore factory defaults, or run firmware updates System

Add or change information about the room where the equipment is

installed, or the phone number for A/V support

Room Labels

Configure time zone or NTP settings Networking

Specify whether idle sessions close automatically Security

Configure IP addressing Networking

View or change the OneLINK device's hostname Networking

View or change the OneLINK device's USB device name Streaming

Access contact information for Vaddio technical support Help

View or download diagnostic logs for technical support Diagnostics

For your convenience, the navigation panel also provides an elegant Logout button for ending your session

gracefully – and leaving the web interface in a password-protected state.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Configuring Network Settings

NETWORKING PAGE

These settings are for the OneLINK device only. The camera is configured separately.

DHCP addressing is the default setting. In a DHCP environment, you will not need to change the network

configuration.

The OneLINK device will use the default address of 169.254.10.1 if no DHCP server is available. In this

situation, you will need to connect a computer to the OneLINK device's network port and configure network

settings. Depending on the computer, you may need a crossover cable.

Caution

Consult your IT department before changing network settings. Errors in network configuration can make

the OneLINK device and connected equipment inaccessible from the network. Do not change

DHCP/Static addressing, IP address, subnet mask, or gateway unless you are very familiar with the

characteristics and configuration of the network where you install the equipment.

To assign a static IP address:

1. Select static IP addressing.

2. Specify the IP address, subnet mask, and gateway address.

3. Save your changes.

Pro Tip

Make sure you have a way to remember the IP address. There is no hardware factory reset.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Assigning a Hostname

NETWORKING PAGE

The default hostname for the OneLINK BridgeAV interface is the string vaddio-onelink-bridge-

followed by the device's MAC address. You can change this in the Hostname field.

If your network supports hostname resolution, you can browse to the OneLINK device by hostname even if

you cannot readily determine its IP address. In this situation, you may wish to assign a hostname

according to your IT department's naming guidelines.

To edit the hostname:

Enter the desired hostname in the Hostname text box, and save your changes.

Specifying Time Zone and NTP Server

NETWORKING PAGE

To ensure that data exports receive accurate time stamps, and to display the correct date and time on the

Networking page, NTP updating must be enabled.

1. Enable Automatic NTP Updating.

2. Select the desired time zone from the list.

3. If desired, specify the NTP server to use. Otherwise, use the default.

4. Select Refresh to update the displayed date and time.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Managing Access and Passwords

SECURITY PAGE

Things you can do on this screen:

nSet whether inactive sessions log off automatically or not

nChange the password for the admin account (default is password)

Note

For best security, Vaddio strongly recommends changing passwords from the default. Using default

passwords leaves the product vulnerable to tampering.

Pro Tip

Make sure you have a way to remember the admin password. There is no hardware factory reset.

Adding Room Information to the Web Interface

ROOM LABELS PAGE

On this page, you can provide information about the OneLINK Bridge AV interface's location:

nName of the organization

nName of the room where the equipment is installed

nPhone number of the room where the equipment is installed

nPhone number for the AV or IT support team

This information appears on every page of the OneLINK web interface.

Note

This does not affect the room information (if any) presented on the web interface for the attached camera.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Configuring Streaming Settings

STREAMING PAGE

The camera's settings are used for IP streaming; the OneLINK BridgeAV interface passes the IP stream

from the camera and does not require additional IP streaming configuration.

For non-USB cameras, the OneLINK Bridge AV interface provides USB streaming capability. On the

Streaming page, you can:

nDisable/enable USB streaming

nAllow the conferencing application to control the audio

nEdit the USB device name

After making changes on this page, save them.

To disable or enable streaming:

USB streaming is enabled by default. Use the Enable USB Streaming checkbox to change this.

To control the audio from a computer:

Check the Enabled box for HID Audio Controls.

Note

When HID Audio Controls are enabled, we recommend controlling volume manually. Allowing the

conferencing application to manage the volume automatically can produce undesirable results.

To edit the USB device name:

To change the way the OneLINK device shows up in your soft client's selection list, edit the USB Device

Name.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Enabling Phantom Power to Microphones

AUDIO PAGE, ANALOG TAB

To supply 48 VDC phantom power to a connected microphone, check the Phantom Power checkbox below

the controls for the Line/Mic input.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Configuring Audio Settings

AUDIO PAGE

The web interface provides separate controls for each of the audio inputs and outputs:

nAnalog (Mic/Line In 1 and 2, and Line Out 1 and 2)

nDigital (HDBT Input left and right, HDMI Output left and right, SDI Output left and right)

nStreaming (USB Playback left and right, HDBT Output left and right, USB Record left and right)

The Matrix tab of the Audio page defines audio routing.

Muting the Microphones

Use the Mute control at the top of any page.

Controlling Volume on Individual Inputs or Outputs

AUDIO PAGE, ANALOG, DIGITAL, AND STREAMING TABS

Use the button to mute the desired audio input or output. Use the slider to set the volume.

Note

For best performance with most computers, we recommend setting the USB Record volume high.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Default Microphone Settings

AUDIO PAGE, ANALOG TAB

Acoustic Echo Cancellation – Enabled; prevents audio feedback by cancelling the specified output

signal out of the line/mic input.

Note

If using the OneLINK Bridge with a conferencing codec, ensure that echo cancellation is enabled on only

one device, whether it is the OneLINK Bridge or the codec. If echo cancellation is enabled on both the

OneLINK Bridge and the codec, unexpected audio effects may result. We recommend disabling echo

cancellation on the OneLINK Bridge and allowing the conferencing codec to handle it.

Noise Cancellation – Enabled; suppresses ambient noise.

Automatic Gain Control – Disabled; adjusts gain to compensate for differences in volume as different

people speak.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Microphone Settings for Environments with Audiences

AUDIO PAGE, ANALOG AND MATRIX TABS

Speech Lift: Feeds the signal from the specified microphone to the speakers in the room, so that people in

the back of the room can hear the person who is speaking.

Chairman Override: Gives priority to the specified microphone when more than one person is speaking.

(Matrix tab only)

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Microphone Adjustments

AUDIO PAGE, ANALOG TAB

To adjust for more natural speech reproduction:

nHigh-pass filter – Specify the lowest frequency that the microphone should pick up. Use this setting to

reduce low-frequency background noise such as heating/air conditioning systems.

nLow-pass filter – Specify the highest frequency that the microphone should pick up. Use this setting to

reduce hissing sounds and make speech sound natural.

nPEQ (parametric equalizer) – Increase or reduce the volume of specific frequency ranges to

compensate for the audio challenges unique to the situation.

Note

As a best practice, use the equalizer to attenuate undesirable frequency ranges rather than to boost the

desirable frequencies.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Speaker Adjustments

AUDIO PAGE, ANALOG AND STREAMING TABS

To sync the sound with the video:

If the video lags noticeably behind the audio, check the Delay box for the appropriate audio outputs (Analog

or Streaming tab) and enter a delay value in msec. The delay may differ from one output to another.

To compensate for differing speech volumes:

If some people on the far end are inaudible while others are too loud, check the Compressor box to reduce

the dynamic range from the connected speakers. (Analog tab only.)

To compensate for specific audio issues on the far end:

Use the equalizers for the analog outputs to attenuate specific frequency ranges. This can help if the far-

end audio includes unwanted elements such as a rumbling HVAC system or a cricket in the room.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Preventing Audio Feedback

AUDIO PAGE, ANALOG TAB

Audio feedback results when the microphones pick up audio from the speakers.

1. Select Echo Cancellation on any line inputs that are connected to signal sources.

2. In the Global Settings, under Master Output/AEC Reference, select the audio output to use as the

reference - the signal that will be cancelled out of the inputs.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Default Audio Matrix

AUDIO PAGE, MATRIX TAB

The audio matrix shows where each audio output originates. Each column of the matrix shows one audio

output, and each row shows one audio input. Table cells highlighted in blue mean that the input represented

in that row is routed to the output represented in that column.

nUSB Playback left and right (far-end audio from the soft conferencing client) route to line output 1

(typically the speaker in your conference room).

nLine/Mic 1 (your room's microphone) routes to USB Record left and right (the audio that the

participants on the far end hear).

nHDBT left and right (far-end audio received as part of the HDMI signal over the HDBT connection)

routes to HDMI Output left and right, and goes to the HDMI display's speakers.

Routing Audio

AUDIO PAGE, MATRIX TAB

To specify how the OneLINK Bridge uses a given audio input, locate its row. Locate the column

representing the desired output and select the table cell where the desired row and column intersect.

Example: The USB stream has left and right audio channels, but by default Line/Mic 1 provides the source

for both channels of outbound USB audio (USB Record left and right) and both channels of incoming USB

audio are routed to Output 1 (Audio Line Out 1). You might choose to change the default matrix to provide

separate right and left channels of outbound and inbound USB audio.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Viewing System Information

SYSTEM PAGE

The information on the System page includes the version – so you don't need to guess about whether the

latest update has already been installed.

The System page also provides controls to:

nReboot the OneLINK device

nBack up or restore configuration data

nRestore factory presets

nUpdate the firmware

Saving (Exporting) or Restoring (Importing) a Configuration

SYSTEM PAGE

You can save a known good configuration by exporting it. This allows you to quickly configure several

OneLINK devices the same way, by importing the configuration to all of them. It also gives you a quick way

to go back to a known good configuration if you are concerned about planned changes on a specific unit.

The configuration file can only be imported to a OneLINK device using the same version of firmware from

which the file was exported. You cannot export a configuration, update the firmware, and import the

configuration – but you won't need to. Firmware updates do not change the device configuration.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

To export the current configuration:

Select Export Data. The configuration file downloads to your computer's default download location as a

.dat file. The filename is the device's hostname.

Note

You can import a configuration file from another OneLINK device; however, the configuration file can only

be imported to a device that is using the same version of firmware from which the file was exported. The

OneLINK device cannot import a configuration file that was exported from a different version of firmware.

To import a configuration file:

1. Select Import Data. The Import Data dialog opens.

2. Select Choose File, and select the configuration file. The filename is the OneLINK device's hostname,

with the file extension .dat. The OneLINK device loads the configuration and reboots.

Rebooting the OneLINK Device

SYSTEM PAGE

This may help if the OneLINK device stops responding as you expect.

In the System Utilities section of the System page, select Reboot.

Restoring Factory Settings

SYSTEM PAGE

Select Restore Factory Settings to return to the default configuration. Read the confirmation message

before you select Continue or Cancel.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Starting a Firmware Update

SYSTEM PAGE

Caution

Do not remove power or disconnect the OneLINK device while a firmware update in progress. Interrupting a

firmware update can make the OneLINK device unusable.

1. Be sure you have downloaded the appropriate update file to your computer.

2. Select Choose File, browse to the firmware update file that you downloaded, and select it. The filename

ends with .p7m. The System page then displays the filename beside the Choose File button.

3. OPTIONAL: Select Export Data to save a copy of the OneLINK device's current configuration. You

probably won't need it, but it could save time if you need to roll back the update.

4. Select Begin Firmware Update.

5. READ the information in the Confirm dialog box and be sure you understand it. It's boring, but it could

save you a lot of time and aggravation.

6. When you are ready to start the update, select Continue.

7. If the update process presents warnings or error messages, read them carefully.

8. Contact Vaddio technical support if you encounter any problems with the update.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Contacting Vaddio Technical Support and Viewing Diagnostics

HELP PAGE, DIAGNOSTICS PAGE

If you encounter an issue that you can't resolve using your superior troubleshooting skills (and perhaps the

Troubleshooting section of this guide), go to the Help page. This page provides Vaddio Technical Support

contact information.

Your Vaddio technical support representative may ask you to download and email the log file available from

the Diagnostics page.

The information on this page does not necessarily indicate errors or problems. Most of it is a log of code

execution that can be helpful later if technical support or engineering staff need to research an issue.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Telnet Serial Command API

The Vaddio Telnet serial command API is a high-level, text-based command line interface to allow an

external device such as AMX or Crestron to control the OneLINK device. Use a Telnet client to access the

API via the network. The default Telnet port is 23. Telnet sessions require the admin account login.

Using a question mark as a command parameter will bring up

a list of available commands for the menu you are in.

Things to know about control via Telnet session:

nCommand lines are terminated with a carriage return.

nAll ASCII characters (including carriage returns) are

echoed to the terminal program and appended with the

VT100 string ESC[J (hex 1B 5B 4A), which most terminal

programs automatically strip.

nCTRL-5 Clears the current serial buffer on the device.

Typographical conventions:

n{ x | y | z} – Choose x, y, or z.

n<variable> – Substitute the desired value here.

n< x - y > – Valid range of values is from x through y.

n[parameter] – Parameter is not required.

Note

The commands in this guide refer to the OneLINK device. To control the camera itself, open a Telnet

session to the camera's IP address and use the camera's Telnet commands.

link power

Sets the camera connection on or off.

Note

The OneLINK device does not provide camera control. To set the camera to standby instead of powering it

off, use the camera's remote or other camera control interface to issue a standby command directly to the

camera.

Synopsis link power { on | off }

Options

off Powers off the camera connection.

on Powers on the camera connection.

Examples >link power off

Powers off the camera connection.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

audio volume

Gets or sets the volume of the specified audio channel.

Synopsis audio [channel] volume {get | on | off | toggle}

Channels

master Applies the command to all audio channels.

line_in_1

line_in_2

Line/Mic In ports (typically microphone inputs).

usb3_playback_left

usb3_playback_right

Audio portion of the incoming (far-end) USB

stream, left and right channels.

hdbt_in_left

hdbt_in_right

Audio portion of the incoming (far-end) HDMI

signal, left and right channels.

line_out_1

line_out_2

Line Out ports (typically speaker outputs).

usb3_record_left

usb3_record_right

Outbound (near-end) audio portion of the USB

stream, left and right channels.

hdmi_out_left

hdmi_out_right

Audio portion of the HDMI output (far-end audio to

the display's speakers), left and right channels.

sdi_out_left

sdi_out_right

Audio portion of the SDI output (far-end audio to

the display's speakers), left and right channels.

hdbt_out_left

hdbt_out_right

Outbound (far-end) audio portion of the IP stream,

left and right channels.

Options get Returns the current volume of the specified

channel.

up Increases the volume of the specified channel.

down Reduces the volume of the specified channel.

set Sets the volume of the specified channel.

Examples audio line_in_1 volume set -5

Sets -5 dB as the volume for the device connected to the Line In 1 port.

audio line_out_1 volume get

volume -10.0 dB

Returns the current volume for the speaker connected to the line out port.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

audio mute

Gets or sets the mute status of the specified audio channel.

Synopsis audio [channel] mute {get | on | off | toggle}

Channels

master Applies the command to all audio channels.

line_in_1

line_in_2

Line/Mic In ports (typically microphone inputs).

usb3_playback_left

usb3_playback_right

Audio portion of the incoming (far-end) USB stream,

left and right channels.

hdbt_in_left

hdbt_in_right

Audio portion of the incoming (far-end) HDMI signal,

left and right channels.

line_out_1

line_out_2

Line Out ports (typically speaker outputs).

usb3_record_left

usb3_record_right

Outbound (near-end) audio portion of the USB

stream, left and right channels.

hdmi_out_left

hdmi_out_right

Audio portion of the HDMI output (far-end audio to the

display's speakers), left and right channels.

sdi_out_left

sdi_out_right

Audio portion of the SDI output (far-end audio to the

display's speakers), left and right channels.

hdbt_out_left

hdbt_out_right

Outbound (far-end) audio portion of the IP stream, left

and right channels.

Options

get Returns the current mute status of the specified

channel.

on Mutes the audio for the specified channel.

off Unmutes the audio for the specified channel.

toggle Changes the mute state for the specified channel –

unmutes if it was muted, mutes if it was not.

Examples > audio line_out_1 mute get

mute: off

Returns the current mute state of the device connected to audio line out 1. Mute is off,

so the audio is on.

>audio master mute on

Mutes all audio.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

audio route

Gets or sets the input routed to the specified output.

Synopsis audio [channel] route {get | set}

Outputs

line_out_1

line_out_2

Line Out ports (typically speaker outputs).

usb3_record_left

usb3_record_right

Outbound (near-end) audio portion of the USB

stream, left and right channels.

hdmi_out_left

hdmi_out_right

Audio portion of the HDMI output (far-end audio to

the display's speakers), left and right channels.

sdi_out_left

sdi_out_right

Audio portion of the SDI output (far-end audio to

the display's speakers), left and right channels.

hdbt_out_left

hdbt_out_right

Outbound (far-end) audio portion of the IP stream,

left and right channels.

Options

get Returns the routing for the specified output.

set Sets the routing for the specified input.

Inputs

line_in_1

line_in_2

Line/Mic In ports (typically microphone inputs).

usb3_playback_left

usb3_playback_right

Audio portion of the incoming (far-end) USB

stream, left and right channels.

hdbt_in_left

hdbt_in_right

Audio portion of the incoming (far-end) HDMI

signal, left and right channels.

Examples > audio line_out_1 route get

[usb3_playback_left usb3_playback_right ]

Returns the current source of the audio output on Line Out 1 (typically a speaker).

Both channels of far-end audio from the USB stream are currently routed to this

output.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

audio crosspoint-gain

Returns or sets the current routing gain, in dB, for the crosspoint between a given output and input.

Synopsis audio <output> crosspoint-gain <input> {get | set <level>}

Outputs

line_out_1

line_out_2

Line Out ports (typically speaker outputs).

usb3_record_left

usb3_record_right

Outbound (near-end) audio portion of the USB

stream, left and right channels.

hdmi_out_left

hdmi_out_right

Audio portion of the HDMI output (far-end audio to

the display's speakers), left and right channels.

sdi_out_left

sdi_out_right

Audio portion of the SDI output (far-end audio to

the display's speakers), left and right channels.

hdbt_out_left

hdbt_out_right

Outbound (far-end) audio portion of the IP stream,

left and right channels.

Inputs

line_in_1

line_in_2

Line/Mic In ports (typically microphone inputs).

usb3_playback_left

usb3_playback_right

Audio portion of the incoming (far-end) USB

stream, left and right channels.

hdbt_in_left

hdbt_in_right

Audio portion of the incoming (far-end) HDMI

signal, left and right channels.

Options

get Returns the gain from the specified input to the

specified output.

set <-12.0 .. 12.0> Sets the gain from the specified input to the

specified output. Valid range is -12.0 dB to 12.0

dB.

Examples > audio program_out_left crosspoint-gain usb3_in_left get

3.9

Returns the gain from the left channel of the USB 3 playback to the left channel of the

program output.

> audio program_out_left crosspoint-gain usb3_in_left set -3

Sets the gain from the left channel of the USB 3 playback to the left channel of the

program output to -3 dB.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

sleep

Pauses for the specified number of milliseconds before evaluating and executing the next command.

Synopsis sleep <milliseconds>

Options <milliseconds> The number of milliseconds (1 to 10000) to

pause.

Example >sleep 7000

Pause for 7 seconds (7000 milliseconds) before returning.

network settings get

Returns the current network settings for MAC address, IP address, subnet mask, and gateway.

Synopsis network settings get

Example > network settings get

Name eth0:WAN

MAC Address 00:1E:C0:F6:CA:7B

IP Address 192.168.1.67

Netmask 255.255.255.0

VLAN Disabled

Gateway 192.168.1.254

Integrator's Complete Guide to the OneLINK Bridge AV Interface

network ping

Sends an ICMP ECHO_REQUEST to the specified IP address or hostname.

Synopsis network ping [count <count>] [size <size>] <destination-ip>

Options <count> The number of ECHO_REQUEST packets to

send. Default is five packets.

<size> The size of each ECHO_REQUEST packet.

Default is 56 bytes.

<destination-ip> The IP address where the ECHO_REQUEST

packets will be sent.

Examples >network ping 192.168.1.66

PING 192.168.1.66 (192.168.1.66): 56 data bytes

64 bytes from 192.168.1.66: seq=0 ttl=64 time=0.476 ms

64 bytes from 192.168.1.66: seq=1 ttl=64 time=0.416 ms

64 bytes from 192.168.1.66: seq=2 ttl=64 time=0.410 ms

64 bytes from 192.168.1.66: seq=3 ttl=64 time=0.410 ms

64 bytes from 192.168.1.66: seq=4 ttl=64 time=3.112 ms

--- 192.168.1.66 ping statistics ---

5 packets transmitted, 5 packets received, 0% packet loss

round-trip min/avg/max = 0.410/0.964/3.112 ms

Sends five ECHO_REQUEST packets of 56 bytes each to the host at

192.168.1.66.

>network ping count 10 size 100 192.168.1.1

Sends 10 ECHO_REQUEST packets of 100 bytes each to the host at 192.168.1.1.

The command returns data in the same form as above.

system reboot

Reboots the system either immediately or after the specified delay. Note that a reboot is required when

resetting the system to factory defaults (system factory-reset).

Synopsis system reboot [<seconds>]

Options <seconds> The number of seconds to delay the reboot.

Examples >system reboot

The system is going down for reboot NOW! onelink-bridge-D8-80-39-62-A7-C5

Reboots the system immediately.

>system reboot 30

Reboots the system in 30 seconds. The response appears at the end of the delay.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

system factory-reset

Gets or sets the factory reset status. When the factory reset status is on, the OneLINK device resets to

factory defaults on reboot.

Note

This does not reset the camera.

Synopsis system factory-reset { get | on | off}

Options get Returns the camera's current factory reset

status.

on Enables factory reset on reboot.

off Disables factory reset on reboot.

Examples >system factory-reset get

factory-reset (software): off

factory-reset (hardware): off

Returns the factory reset status.

This evaluates the most recent system factory-reset on or off command, if

one has been received, then reads the rear panel DIP switches and returns the

status on if they are all in the down position.

>system factory-reset on

factory-reset (software): on

factory-reset (hardware): off

Enables factory reset upon reboot.

Note

This command does not initiate a factory reset. The factory reset takes place on the

next reboot.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

history

Returns the most recently issued commands from the current Telnet session. Since many of the programs

read user input a line at a time, the command history is used to keep track of these lines and recall historic

information.

Synopsis history <limit>

Options <limit> Integer value specifying the maximum number

of commands to return.

Examples history

Displays the current command buffer.

history 5

Sets the history command buffer to remember the last 5 unique entries.

Additional

information

You can navigate the command history using the up and down arrow keys.

This command supports the expansion functionality from which previous

commands can be recalled from within a single session. History expansion is

performed immediately after a complete line is read.

Examples of history expansion:

* !! Substitute the last command line.

* !4 Substitute the 4th command line (absolute as per ’history’ command)

* !-3 Substitute the command line entered 3 lines before (relative)

version

Returns the current firmware version of the OneLINK device.

Synopsis version

Example version

Returns current firmware version information in a form something like

this:

Audio 1.05-1.01

Commit a735fee1ab6270e693e2791b76a9bcbdf5bd36b5

HDLink RX4.6.1x0.01

System Version OneLINK Bridge 1.0.0

USB 01.00.017

Video 1.06

Integrator's Complete Guide to the OneLINK Bridge AV Interface

help

Displays an overview of the CLI syntax.

Synopsis help

Example help

exit

Ends the command session and closes the socket.

Synopsis exit

Example exit

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Specifications

Capabilities

Video outputs Simultaneous HDMI, USB 3.0 and HD-SDI

USB 3.0 Streaming Originates USB 3.0 stream with

uncompressed video and

bidirectional stereo audio

IP Streaming Passes the stream from the

camera, if enabled

Audio inputs Two mic/line-level channels with

noise/echo cancellation;

phantom power available

Audio outputs Two balanced line-level audio

outputs

Mixing 10X8 audio mixer; audio is routable through all outputs

Control Features Web interface for configuration via browser

Telnet API for third-party external control

Ethernet and RS-232 control pass-through to camera

USB Human Interface Device (HID) for room audio controls

Maximum cable

length

328 ft (100m) Cat-5e cable; shielded Cat-6 recommended where EMI/RF interference is

an issue

Power, Physical, and Environmental

Input Power 48 VDC, 1.36 A Output Power to

Camera

12 VDC, 3.0 A

Height 1.72 in. (4.4 cm)/1U Width 8.38 in. (21.3 cm)

Depth 6.0 in. (15.2 cm) Weight 1.7 lb. (0.8 kg)

Operating/Storage

Temperature

32° to 104° F (0° to 40° C) Operating/Storage

Humidity

20% to 80% RH, non-

condensing

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Troubleshooting

When the Vaddio camera connected to the OneLINK device doesn't behave as you expect, check the color

of the camera's indicator light before you do anything else – but keep in mind that the camera's indicator

can be turned off in the administrative interface.

nPurple – booting or in standby (low power) mode.

nBlue – normal operation.

nRed – Tally function; the camera is on-air.

nBlinking red – fault condition.

nYellow – firmware update in progress.

Now check the OneLINK device's web interface for error messages. The EZIM (if one is used) tends to run

warm, which is normal. If the system detects that the temperature is too high, a temperature fault message

will appear at the top of the web interface page.

If neither of these reveal the problem, use this table to determine whether it's time to call Vaddio Technical

Support.

What is it doing? Possible causes Check and correct

Nothing.

The camera is not

receiving power.

The camera is not connected to the

EZIM (if an EZIM is used).

Plug the EZIM into the camera.

The OneLINK device's power pack is

not plugged in to main power, or the

EZIM (if one is used) is not connected to

the main OneLINK unit.

Plug the power pack into a wall outlet, or

connect the EZIM to its OneLINK base

unit.

At least one of the cables is bad. Replace the bad cable.

The wall outlet is not active. (Check by

finding out if it powers something else,

such as a laptop or phone charger.)

Plug the OneLINK power pack into a

different outlet.

"He's dead, Jim." Contact your reseller or Vaddio Technical

Support.

Camera does not

finish booting or

does not go to the

ready state.

Camera firmware may be out of date. Check the camera's firmware version;

update the camera firmware if necessary.

Possible cable issue. Test with shorter cables.

Try re-terminating the cable.

The camera is on,

but its web interface

is not available.

A cable is not connected. Make sure all network and OneLINK

cables are connected.

The network or OneLINK cable is bad. Replace the bad cable.

The camera is not using the IP address

you browsed to.

Vaddio cameras: Press the Data Screen

button on the remote to see the camera's

IP address.

No communication

with camera

Ethernet or RS-232 cable is connected

to the wrong port at one end.

Check the cables from the EZIM or

OneLINK device to the camera.

The wrong cable is connected (standard

Cat-5e cable where a custom Cisco

cable is needed, or vice-versa) or the

Be sure you are using the right cable.

If using a custom Cisco cable, be sure it

is connected according to the instructions

Integrator's Complete Guide to the OneLINK Bridge AV Interface

What is it doing? Possible causes Check and correct

custom cable is connected the wrong

direction.

on its labels.

The camera is not compatible with the

OneLINK device.

Be sure you are using your OneLINK

device with a compatible camera.

The camera is on

but not transmitting

video.

Possible cable length issue. Check the HDMI output from the camera

by connecting a display directly to it. If

video is good using a relatively short

cable directly to the display, then a better

grade of cable (Cat-6 or Cat-7) may

correct the problem.

Video drops out

repeatedly.

If this happens during PTZ movements,

the camera is not getting adequate

power.

Check how the camera behaves when it

and the attached EZIM are connected to

the main interface with a short (6 to 10 ft/

2 to 3 m) cable. If the camera performs

properly, then the problem is the length of

the cable from the main interface to the

EZIM. A better grade of cable (Cat-6 or

Cat-7) may correct the problem.

Possible cable inductance issue. Do not store excess cable by coiling it

neatly.

Best practice: Build cables to the required

length.

Video and audio

don't match up –

speech is audible

before the person on

the far end appears

to start speaking.

The audio signal is arriving before the

video signal, which is normal but not

desirable.

For the affected audio outputs (Line Out,

HDMI Out, or USB Record), enable

Delay and enter a value in milliseconds.

When connected to

a conferencing

codec: Far-end

audio drops out

periodically, and the

issue may intensify.

Echo cancellation is enabled on both the

codec and the OneLINK Bridge.

Disable echo cancellation on the

OneLINK Bridge.

Audio feedback or

echo that

intensifies.

Echo cancellation is disabled. If using the OneLINK Bridge with a

conferencing codec, enable echo

cancellation on the codec. Otherwise,

enable echo cancellation on the OneLINK

Bridge.

Polycom camera

does not respond to

the remote.

The OneLINK Bridge AV interface has

no IR forwarding.

Point the remote at the conferencing

codec.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Operation, Storage, and Care

For smears or smudges on the product, wipe with a clean, soft cloth. Use a lens cleaner on the lens. Do not

use any abrasive chemicals.

Keep this device away from food and liquids.

Do not operate or store the device under any of the following conditions:

nTemperatures above 40°C (104°F) or below 0°C (32°F)

nHigh humidity, condensing or wet environments

nInclement weather

nSevere vibration

nLateral acceleration of more than 27G

nDry environments with an excess of static discharge

Do not attempt to take this product apart. There are no user-serviceable components inside.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Compliance Statements and Declarations of Conformity

Statements are given separately for the OneLINK Bridge AV interface and the OneLINK HDMI EZCamera

Interface Module (EZIM).

OneLINK Bridge AV Interface

Compliance testing was performed to the following regulations:

FCC Part 15 (15.107, 15.109), Subpart B Class A

ICES-003, Issue 6, January 2016 Class A

EN 55024, 2010 Class A

EN 55032, 2012 Class A

EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011 + A2: 2013 Safety

KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A

EMC Directive 2014/30/EU Class A

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause

interference, and (2) This device must accept any interference including interference that

may cause undesired operation of the device.

Changes or modifications not expressly approved by Milestone AV Technologies can affect

emission compliance and could void the user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus

set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’emet pas de bruits radioélectriques

dépassant les limites applicables aux appareils numeriques de la classe A

préscrites dans le Règlement sur le brouillage radioélectrique édicte par le ministère des Communications

du Canada.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions

and Immunity and meets the requirements for a Class A digital device. In a domestic environment this

product may cause radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:

EMC Directive 2014/30/EU

EN 55032: 2012 Multimedia Equipment Emissions Requirements

EN 55024: 2010 IT Immunity Characteristics

EN 61000-4-2 + Amendments A1, A2 Electrostatic Discharge

EN 61000-4-3 + A1 Radiated Immunity

EN 61000-4-4 + Corrigendum Electrical Fast Transients

EN 61000-4-5 Surge Immunity

EN 61000-4-6 Conducted Immunity

EN 61000-4-8 Power Frequency Magnetic Field

EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

KN24 2008 (CISPR 24: 1997 + A1: 2000 +

A2: 2002)

IT Immunity Characteristics

EN 61000-4-2 Electrostatic Discharge

EN 61000-4-3 Radiated Immunity

EN 61000-4-4 Electrical Fast Transients

EN 61000-4-5 Surge Immunity

EN 61000-4-6 Conducted Immunity

EN 61000-4-8 Power Frequency Magnetic Field

EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

Low Voltage Directive 2014/35/EU

IEC 60950-1: 2005 (2nd Edition); Am 1: 2009

+ Am 2: 2013

Safety

EN 60950-1: 2006 + A11: 2009 + A1: 2010 +

A12: 2011 + A2: 2013

Safety

RoHS Directive 2011/65/EU

Integrator's Complete Guide to the OneLINK Bridge AV Interface

OneLINK HDMI EZCamera Interface Module (EZIM)

Compliance testing was performed to the following regulations:

nFCC Part 15 (15.107, 15. 109), Subpart B Class A

nICES-003, Issue 4: 2004 Class A

nEN 55022 A: 2006 + A1: 2007 Class A

nKN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) Class A

nKN22 2008 (CISPR 22: 2006) Class A

nEMC Directive 2004/108/EC Class A

nEN 55024: A2: 2003 Class A

nEN 60950-1:2006+A11: 2009+A1: 2010+A12: 2011 Safety

FCC Part 15 Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15, Subpart B, of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at his/her own expense.

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2)

This device must accept any interference including interference that may cause undesired operation of the

device.

Changes or modifications not expressly approved by Vaddio can affect emission compliance and could

void the user’s authority to operate this equipment.

ICES-003 Compliance

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus

set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux

appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte

par le ministère des Communications du Canada.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

European Compliance

This product has been evaluated for Electromagnetic Compatibility under the EMC Directive for Emissions

and Immunity and meets the requirements for a Class A digital device. In a domestic environment this

product may cause radio interference in which case the user may be required to take adequate measures.

Standard(s) To Which Conformity Is Declared:

EMC Directive 2004/108/EC

EN 55022:2010 Conducted and Radiated Emissions

EN 55024: 1998 + Amendments A1: 2001 + A2: 2003 Immunity

nEN 61000-4-2: 1995 + Amendments A1: 1998 + A2: 2001 Electrostatic Discharge

nEN 61000-4-3: 2006 + A1: 2008 Radiated Immunity

nEN 61000-4-4: 2004 + Corrigendum 2006 Electrical Fast Transients

nEN 61000-4-5: 2006 Surge Immunity

nEN 61000-4-6: 2009 Conducted Immunity

nEN 61000-4-8: 2010 Power Frequency Magnetic Field

nEN 61000-4-11: 2004 Voltage Dips, Interrupts and Fluctuations

KN24 2008 (CISPR 24: 1997 + A1: 2000 + A2: 2002) IT Immunity Characteristics

nEN 61000-4-2 Electrostatic Discharge

nEN 61000-4-3 Radiated Immunity

nEN 61000-4-4 Electrical Fast Transients

nEN 61000-4-5 Surge Immunity

nEN 61000-4-6 Conducted Immunity

nEN 61000-4-8 Power Frequency Magnetic Field

nEN 61000-4-11 Voltage Dips, Interrupts and Fluctuations

IEC 60950-1:2005 (2nd Edition); Am 1:2009 Safety

EN 60950-1: 2006+A11: 2009+A1: 2010+A12: 2011 Safety

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Warranty Information

See Vaddio Warranty, Service and Return Policies posted on support.vaddio.com for complete details.

Hardware* warranty: Two (2) year limited warranty on all parts and labor for Vaddio manufactured

products. Vaddio warrants its manufactured products against defects in materials and workmanship for a

period of two years from the day of purchase, to the original purchaser, if Vaddio receives notice of such

defects during the warranty. Vaddio, at its option, will repair or replace products that prove to be

defective. Vaddio manufactures its hardware products from parts and components that are new or

equivalent to new in accordance with industry standard practices.

Exclusions: The above warranty shall not apply to defects resulting from improper or inadequate

maintenance by the customer, customers applied software or interfacing, unauthorized modifications or

misuse, mishandling, operation outside the normal environmental specifications for the product, use of the

incorrect power supply, modified power supply or improper site operation and maintenance. OEM and

special order products manufactured by other companies are excluded and are covered by the

manufacturer’s warranty.

Vaddio Customer Service: Vaddio will test, repair, or replace the product or products without charge if the

unit is under warranty. If the product is out of warranty, Vaddio will test then repair the product or

products. The cost of parts and labor charge will be estimated by a technician and confirmed by the

customer prior to repair. All components must be returned for testing as a complete unit. Vaddio will not

accept responsibility for shipment after it has left the premises.

Vaddio Technical Support: Vaddio technicians will determine and discuss with the customer the criteria

for repair costs and/or replacement. Vaddio Technical Support can be contacted by email at

support@vaddio.com or by phone at one of the phone numbers listed on support.vaddio.com.

Return Material Authorization (RMA) number: Before returning a product for repair or replacement

request an RMA from Vaddio’s technical support. Provide the technician with a return phone number, e-

mail address, shipping address, product serial numbers and original purchase order number. Describe the

reason for repairs or returns as well as the date of purchase. See the General RMA Terms and Procedures

section for more information. RMAs are valid for 30 days and will be issued to Vaddio dealers only. End

users must return products through Vaddio dealers. Include the assigned RMA number in all

correspondence with Vaddio. Write the assigned RMA number clearly on the shipping label of the box when

returning the product. All products returned for credit are subject to a restocking charge without

exception. Special order product are not returnable.

Voided varranty: The warranty does not apply if the original serial number has been removed or if the

product has been disassembled or damaged through misuse, accident, modifications, use of incorrect

power supply, use of a modified power supply or unauthorized repair.

Shipping and handling: Vaddio will not pay for inbound shipping transportation or insurance charges or

accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound

shipping, transportation, and insurance charges for all items under warranty but will not assume

responsibility for loss and/or damage by the outbound freight carrier. If the return shipment appears

damaged, retain the original boxes and packing material for inspection by the carrier. Contact your carrier

immediately.

Products not under warranty: Payment arrangements are required before outbound shipment for all out of

warranty products.

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Index

acoustic echo cancellation 55

adjusting microphones 56

admin login 47, 51

AGC (automatic gain control) 55, 57

ambient noise, suppressing 55

anatomy of the EZCamera Interface Module 9

anatomy of the OneLINK device 7-8

API 65, 74

syntax help 74

audio 54-60, 66-69

controls 54-58

crosspoint gain 69

delay 57-58

feedback, preventing 55, 59

matrix, default 60

matrix, editing 60, 68

muting 54, 67

routing 60

volume 54, 66

Audio page (web) 53-60

automatic gain control 55

automatic inactivity time-out (web

session) 51

automatic NTP updating 50

backing up a configuration 61

browser compatibility 46

cable connectors 8-10

cables 2, 10, 17, 20, 26, 31, 33, 37, 44, 75

Cisco split 17, 26, 37, 44

maximum length 2, 10, 75

null-modem 20, 26, 37, 44

Polycom fan-out, codec, terminating 33

Polycom fan-out, codec, terminating |

Models.All OneLINK HDMI |

Models.All OneLINK HDMI [54] 31

capabilities 2

chairman override (microphone setting) 56

cheat sheet, web interface 48

cleaning 78

Codec Control Mode (Vaddio cameras) 16,

21, 31, 38

command execution delay 70

command history 73

compatibility, browsers 46

configuration, saving or restoring 61

configuring 13, 16, 21, 23, 31, 38, 45, 59

AEC reference 21, 38, 45, 59

connected RoboSHOT HDMI camera 23,

31, 38

connected Vaddio HDBaseT camera 13,

16, 21

connection diagram 11-20, 22-37, 40-44

block, HDBaseT camera 12

block, HDBaseT camera with codec 14

block, HDMI camera 22

block, HDMI camera with codec 29

Cisco Precision 40 25

Cisco Precision 40 with Cisco C20 40

Cisco Precision 40 with Cisco C40 41

Cisco Precision 40 with Cisco C60 41

Cisco Precision 40 with Cisco SX20 42

Cisco Precision 40 with Cisco SX80 43

Cisco Precision 60 26

Cisco Precision 60 with Cisco SX80 44

Cisco Precision HD 25

Cisco Precision HD with Cisco C20 40

Cisco Precision HD with Cisco C40 41

Cisco Precision HD with Cisco C60 41

Cisco Precision HD with Cisco SX20 42

Cisco Precision HD with Cisco SX80 43

Panasonic AW-HE130 27

Polycom EagleEye IV 24

Polycom EagleEye IV with Polycom RPG

310 32

Polycom EagleEye IV with Polycom RPG

500 32

Polycom EagleEye IV with Polycom RPG

700 33

RoboSHOT HDMI 23

RoboSHOT HDMI with Cisco C20 34

RoboSHOT HDMI with Cisco C40 35

RoboSHOT HDMI with Cisco C60 35

RoboSHOT HDMI with Cisco SX20 36

RoboSHOT HDMI with Cisco SX80 37

RoboSHOT HDMI with Polycom RPG

310 30

RoboSHOT HDMI with Polycom RPG

500 30

RoboSHOT HDMI with Polycom RPG

700 31

Sony SRG120 28

Sony SRG300 28

Vaddio HDBaseT 13

Vaddio HDBaseT with Cisco C20 17

Vaddio HDBaseT with Cisco C40 18

Vaddio HDBaseT with Cisco C60 18

Vaddio HDBaseT with Cisco SX20 19

Vaddio HDBaseT with Cisco SX80 20

Vaddio HDBaseT with Polycom RPG

310 15

Vaddio HDBaseT with Polycom RPG

500 15

Vaddio HDBaseT with Polycom RPG

700 16

visual conventions 11

connectors 8-11

identification 8-9

pin-outs, RS-232 11

customer-provided items 4, 6, 13, 15, 17, 23-

25, 27, 30, 32, 34, 39

cycle power to the camera 65

damage, preventing 10

date and time 50

default password 47

default settings, restoring 62, 72

DHCP 49

Diagnostics page (web) 64

dynamic range 57

echo cancellation 55, 57, 59

equalizer 57-58

equipment location information 51

factory defaults, restoring 62, 72

fault isolation 76

firmware update 63

firmware version 73

getting help 64

graphic equalizer 58

hardware reset 7

hardware specifications 75

Help page (web) 64

HID audio controls 52

high-pass filter adjustment (microphones) 57

hostname, assigning 50

importing a configuration 61

inactive sessions (web interface) 51

indicator lights 7, 76

information, equipment location 51

installation 11

mounting 11

IP address 47, 49

default 49

IP address display 7

IP streaming 52

IR forwarding 16, 31, 33

items you will need 4, 6, 13, 15, 17, 23-25, 27,

30, 32, 34, 39

key for connection diagrams 11

kits 1, 3-6, 12-15, 17, 22-25, 27, 29-30, 32, 34,

for Cisco cameras 25

for Cisco cameras with Cisco codecs 6,

22, 29, 39

for Panasonic cameras 4, 22, 27

for Polycom cameras 24

for Polycom cameras with Polycom

codecs 5, 22, 29, 32

for RoboSHOT HDMI cameras 4, 22-23

for RoboSHOT HDMI cameras with Cisco

codecs 6, 29, 34

for RoboSHOT HDMI cameras with Poly-

com codecs 5, 29-30

for Sony cameras 4, 22, 27

for Vaddio HDBaseT cameras 3, 12-13

for Vaddio HDBaseT cameras with Cisco

codecs 4, 14, 17

for Vaddio HDBaseT cameras with Poly-

com codecs 3, 14-15

line types in diagrams 11

locations of connectors 8-9

low-pass filter adjustment (microphones) 57

MAC address display 7

mic boost 57

Integrator's Complete Guide to the OneLINK Bridge AV Interface

microphones 53-56, 67

acoustic echo cancellation 55

adjusting volume 54

automatic gain control 55

chairman override 56

default settings 55

filter adjustments 57

muting 54, 67

noise cancellation 55

PEQ (parametric equalizer) 57

powering 53

speech lift adjustment 56

muting audio 54, 67

microphones 54

speakers 54

network configuration 49

changing 49

default 49

network configuration information (Telnet) 70

Networking page (web) 49-50

noise cancellation 55, 57

NTP server 50

operating environment 78

packing lists 3-6

999-9595-000/001/009 3

999-9620-000/001/009 5

999-9630-000/001/009 4

999-9640-000/001/009 5

999-9645-000/001/009 3

999-9660-000/001/009 6

999-9670-000/001/009 6

999-9675-000/001/009 4

999-9690-000/001/009 4

page 49-64

Audio 53-60

Diagnostics 64

Help 64

Networking 49-50

Room Labels 51

Security 51

Streaming 52

System 61-63

passwords 47, 51

changing 51

default 47

PEQ (parametric equalizer) 57

performance specifications 75

phantom power 53

physical and environmental specifications 75

pin-outs 11

for RS-232 connectors 11

ping command 71

power on/power off 46, 65

camera 65

powering microphones 53

problems, solving 76

product capabilities 2

product returns and repairs 83

product SKUs 1, 3-6

quick reference, web interface 48

rebooting 62, 71

reset button location 7

restoring a configuration 61

restoring default settings 62, 72

RJ-45 connectors, recommendation 10

room information, adding 51

Room Labels page (web) 51

routing audio 60, 68

RS-232 adapter for Cisco products 20, 37, 44

RS-232 connector pin-out 11

saving a configuration 61

Security page (web) 51

settings, default, restoring 62, 72

software update 63

solving problems 76

speakers 54, 58, 67

adjusting for differing speech volumes 58

adjusting volume 54

equalizer 58

muting 54, 67

synchronizing audio with video 58

specifications 75

speech lift (microphone setting) 56

static IP address 49

storage environment 78

Integrator's Complete Guide to the OneLINK Bridge AV Interface

storing a configuration 61

Streaming page (web) 52

streaming settings 52

supported web browsers 46

synchronizing audio with video 58

System page (web interface) 61-62

System page (web) 63

system time 50

technical support 64

Telnet command help 74

Telnet session 65, 73-74

ending 74

history 73

temperature, operating and storage 78

time zone 50

troubleshooting 76

typographical conventions for command ref-

erence 65

updating firmware 63

USB device name 52

USB Record volume 54

USB streaming 52

version, firmware 73

volume controls 54, 66

warranty 10, 83

web browsers supported 46

web interface 48-64

Audio page 53-60

cheat sheet 48

Diagnostics page 64

Help page 64

Networking page 49-50

Room Labels page 51

Security page 51

Streaming page 52

System page 61-63

Integrator's Complete Guide to the OneLINK Bridge AV Interface

Vaddio is a brand of Milestone AV Technologies · www.vaddio.com · Phone 800.572.2011 /

+1.763.971.4400 · Fax +1.763.971.4464 · Email info@vaddio.com

Visit us at support.vaddio.com for firmware updates, specifications, drawings, manuals, and technical

support information. Vaddio, OneLINK, and RoboSHOT are trademarks or registered trademarks of

Milestone AV Technologies. The terms HDMI and HDMI High-Definition Multimedia Interface, and the

HDMI logo, are trademarkes or registered trademarks of HDMI Licensing LLC in the United States and

other countries. HDBaseT™ and the HDBaseT Alliance logo are trademarks of the HDBaseT Alliance.

Exmor® is a trademark of Sony Corporation. All other brand names or marks are used for identification

purposes and are trademarks of their respective owners. In British Columbia, Milestone AV Technologies

ULC carries on business as MAVT Milestone AV Technologies ULC.

Table of Contents

Vaddio RoboSHOT 12 HDBT OneLINK User Manual

Related Manuals

Vaddio RoboSHOT 12 HDBT OneLINK HDMI Manual

Vaddio RoboSHOT 12 HDBT OneLINK HDMI Manual

Vaddio RoboSHOT 12 HDBT OneLINK HDMI Manual

Vaddio RoboSHOT 12 HDBT OneLINK HDMI Manual