Table of Contents
- LS620X_en.pdf
- Table of contents
- Important safety instructions
- Introduction
- Positioning your projector
- Connection
- Operation
- Starting up the projector
- Using the menus
- Utilizing the password function
- Switching input signal
- Adjusting the projected image
- Magnifying and searching for details
- Selecting the aspect ratio
- Optimizing the image
- Setting the presentation timer
- Hiding the image
- Locking control keys
- Operating in a high altitude environment
- Using the 3D functions
- Controlling the projector through a LAN environment
- Using the projector in standby mode
- Adjusting the sound
- Shutting down the projector
- Menu operation
- Maintenance
- Troubleshooting
- Specifications
- Copyright information
Viewsonic LS620X User Manual
Displayed below is the user manual for LS620X by Viewsonic which is a product in the Data Projectors category. This manual has pages.
Related Manuals
LS620X
DLP Projector
User Guide
Model No. VS16942
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
ZZZYLHZVRQLFFRP LQ(QJOLVKRULQ VSHFL¿FODQJXDJHV XVLQJWKH 5HJLRQDOVHOHFWLRQ
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the follow-
ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHG
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXU
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKH
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGHÀXRUHVFHQW
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
iv
Copyright Information
Copyright © ViewSonic® Corporation, 2017. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFX-
ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name: LS620X
ViewSonic DLP Projector
Model Number: VS16942
Document Number: LS620X_UG_ENG Rev. 1A 03-21-17
Serial Number: ________________________________________
Purchase Date: ________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
1
Table of contents
Important safety
instructions .......................2
Introduction......................4
Projector features ................................. 4
Shipping contents................................. 4
Controls and functions ......................... 5
Positioning your
projector............................9
Choosing a location.............................. 9
Projection dimensions........................ 10
Connection ......................12
Connecting a computer or monitor .... 14
Connecting Video source devices ...... 15
Playing sound through the projector .. 17
Operation ........................18
Starting up the projector..................... 18
Using the menus................................. 19
Utilizing the password function ......... 20
Switching input signal........................ 22
Adjusting the projected image ........... 23
Magnifying and searching for details. 24
Selecting the aspect ratio ................... 24
Optimizing the image......................... 25
Setting the presentation timer ............ 29
Hiding the image................................ 30
Locking control keys.......................... 30
Operating in a high altitude
environment ....................................... 30
Using the 3D functions ...................... 31
Controlling the projector through
a LAN environment ........................... 31
Using the projector in standby mode
........................................................... 38
Adjusting the sound ........................... 38
Shutting down the projector .............. 39
Menu operation.................................. 40
Maintenance ...................48
Care of the projector .......................... 48
Using the dust filter ........................... 49
Light source information ................... 50
Troubleshooting .............53
Specifications ..................54
Dimensions ........................................ 54
Ceiling mount installation ................. 54
IR control table .................................. 55
RS232 command table....................... 56
Timing chart ...................................... 61
Projector specifications...................... 65
Copyright information...66
2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1. Please read this manual before you operate your projector. Save it for future
reference.
2. Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter or remove the lens cap when the projector light
source is on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
6. Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the light source, press BLANK on the projector or
remote control.
7. Do not operate light sources beyond the rated light source life. Excessive operation of
light sources beyond the rated life could cause them to break on rare occasions.
8. Never replace the light source assembly or any electronic components unless the
projector is unplugged.
9. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
10. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the light source which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
11. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
3
12. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
13. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the light source.
14. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
15. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
16. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
17. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
18. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
19. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
20. CAUTION
Possibly hazardous optical radiation emitted from this product. Do not stare at
operating light source. May be harmful to the eyes. Risk Group 2
Warning
• THIS APPARATUS MUST BE EARTHED.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed
wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a
fault should occur during operation of the unit, operate the disconnect device to switch
the power supply off, or disconnect the power plug.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommend that you also purchase a separate security cable and attach it securely to
both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This
will perform the secondary role of restraining the projector should its attachment to the
mounting bracket become loose.
4
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
Some of the features may not be available on your projector. Actual performance may vary
and subject to model specifications.
• Power saving function decreasing the power consumption of the light source by up to
70% when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
• LAN Settings allowing management of projector status from a remote computer
• Supports 3D display
•Color Management allowing color adjustments to your liking
• Less than 0.5W power consumption when power saving mode is turned on
• Screen Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• Color modes providing choices for different projection purposes
• One-key auto-adjustment to display the best picture quality (only for analog signal)
• Digital keystone correction to correct distorted images
• Adjustable color management control for data/video display
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Component HDTV compatibility (YPbPr)
The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is directly proportional to
projection distance.
The light source brightness will decline over time and may vary within the light source
manufacturers specifications. This is normal and expected behavior.
Shipping contents
1. Projector
2. Power Cord
3. Multi-language User Manual CD
4. Quick Start Guide
5. Remote Control & Batteries
6. VGA Cable
7. Dust filter
8. VGA-Component adapter (optional)
5
Controls and functions
Projector
•Power
Toggles the projector between standby
mode and Power ON.
•/ (Keystone keys)
Manually corrects distorted images
resulting from an angled projection.
• Left/ Right/ Up/ Down
Selects the desired menu items and makes
adjustments when the On-Screen Display
(OSD) menu is activated.
•Menu
Turns on the On-Screen Display (OSD)
menu.
•Exit
Goes back to previous OSD menu, exits
and saves menu settings.
•Enter
Enacts the selected On-Screen Display
(OSD) menu item when the On-Screen
Display (OSD) menu is activated.
• Auto Sync
Automatically determines the best picture
timings for the displayed image.
• Source
Displays the source selection bar.
BLANK SOURCE
ENTER
AUTO
SYNC
MENU
EXIT
Focus ring
Power indicator light
Light
source
indicator
light
Temperature indicator light
6
Remote control
•Power
Toggles the projector between standby
mode and Power ON.
•COMP1
Selects source from COMPUTER 1
port for display.
•COMP2
Selects source from COMPUTER 2
port for display.
•HDMI
Selects source from HDMI and/or
MHL port for display.
• Auto Sync
Automatically determines the best
picture timings for the displayed
image.
•Video
Selects video source for display.
• Source
Displays the source selection bar.
• / (Keystone keys)
Manually corrects distorted images
resulting from an angled projection.
• Left/ Right/ Up/ Down
Selects the desired menu items and
makes adjustments.
•Enter
Enacts the selected On-Screen Display
(OSD) menu item.
•Menu
Turns on the On-Screen Display
(OSD) menu.
•Exit
Exits and saves menu settings.
7
Operating the LASER pointer
The Laser Pointer is a presentation aid for professionals. It emits colored light when you
press it. The laser beam is visible. It is necessary to press and hold Laser for continuous
output.
Do not look into the laser light window or shine the laser light beam on yourself or others. See
the warning messages on the back of the remote control prior to using it.
The laser pointer is not a toy. Parents should be mindful of the dangers of laser energy and
keep this remote control out of the reach of children.
Remote control effective range
Refer to the illustration about the location of the Infra-Red (IR) remote control sensor(s).
The remote control must be held at an angle within 30 degrees perpendicular to the
• (Laser)
Emits visible laser pointer light for
presentation purposes.
• (Aspect Ratio)
Displays the aspect ratio selection bar.
• (Information)
Displays the INFORMATION menu.
•3D
Displays the 3D menu.
•Blank
Hides the screen picture.
• Freeze
Freezes or resumes the projected image.
• Pattern
Displays embedded test pattern.
• (Mute)
Toggles the projector audio between on and
off.
• (Volume Up)
Increases the projector volume.
• (Volume Down)
Decreases the projector volume.
• (Presentation Timer)
Displays the presentation timer settings
menu.
• (Zoom)
Displays the zoom bar that magnifies or
reduces the projected picture size.
•Eco Mode
Selects a light source mode.
•Color Mode
Selects an available picture setup mode.
8
projector's IR remote control sensor(s) to function correctly. The distance between the
remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensor(s) on the
projector that might obstruct the infra-red beam.
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, press on the
finger grip on the cover and slide it down in the direction of the arrow as illustrated.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and pushing it back down into position.
Stop when it clicks into place.
WARNING
• Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are drained or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
Approx. 30°
Approx. 30°
9
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of the following possible installation
locations:
1. Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2. Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM > Projector
Position menu after you turn the projector on.
3. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM > Projector
Position menu after you turn the projector on.
4. Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM > Projector
Position menu after you turn the projector on.
10
Projection dimensions
The "screen" mentioned below refers to the projection screen usually consisting of a screen
surface and a support structure.
Please see "Projector specifications" on page 65 for the native display resolution of this
projector.
For models with a 4:3 native aspect ratio
(a) Screen Size
[inch (cm)]
4:3 image on a 4:3 Screen
(b) Projection distance
[m (inch)] (c) Image height
[cm (inch)]
(d) Vertical offset
[cm (inch)]
min. max. min. max.
60 (152) 0.74 (29) 0.74 (29) 91.44 (36) 13.72 (5.4) 13.72 (5.4)
70 (178) 0.86 (34) 0.86 (34) 106.68 (42) 16.00 (6.3) 16.00 (6.3)
80 (203) 0.98 (39) 0.98 (39) 121.92 (48) 18.29 (7.2) 18.29 (7.2)
90 (229) 1.11 (44) 1.11 (44) 137.16 (54) 20.57 (8.1) 20.57 (8.1)
100 (254) 1.23 (48) 1.23 (48) 152.40 (60) 22.86 (9.0) 22.86 (9.0)
110 (279) 1.35 (53) 1.35 (53) 167.64 (66) 25.15 (9.9) 25.15 (9.9)
120 (305) 1.48 (58) 1.48 (58) 182.88 (72) 27.43 (10.8) 27.43 (10.8)
130 (330) 1.60 (63) 1.60 (63) 198.12 (78) 29.72 (11.7) 29.72 (11.7)
140 (356) 1.72 (68) 1.72 (68) 213.36 (84) 32.00 (12.6) 32.00 (12.6)
150 (381) 1.85 (73) 1.85 (73) 228.60 (90) 34.29 (13.5) 34.29 (13.5)
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(f): Center of lens(e): Screen
• 4:3 image on a 4:3 screen
• 4:3 image on a 16:10 screen
(a)
(c)
(b)
(e)
(f)
(d)
11
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
(a) Screen Size
[inch (cm)]
4:3 image on a 16:10 Screen
(b) Projection distance
[m (inch)] (c) Image height
[cm (inch)]
(d) Vertical offset
[cm (inch)]
min. max. min. max.
60 (152) 0.65 (26) 0.65 (26) 80.77 (32) 12.12 (4.8) 12.12 (4.8)
70 (178) 0.76 (30) 0.76 (30) 94.23 (37) 14.14 (5.6) 14.14 (5.6)
80 (203) 0.87 (34) 0.87 (34) 107.70 (42) 16.15 (6.4) 16.15 (6.4)
90 (229) 0.98 (39) 0.98 (39) 121.16 (48) 18.17 (7.2) 18.17 (7.2)
100 (254) 1.09 (43) 1.09 (43) 134.62 (53) 20.19 (7.9) 20.19 (7.9)
110 (279) 1.20 (47) 1.20 (47) 148.08 (58) 22.21 (8.7) 22.21 (8.7)
120 (305) 1.30 (51) 1.30 (51) 161.54 (64) 24.23 (9.5) 24.23 (9.5)
130 (330) 1.41 (56) 1.41 (56) 175.01 (69) 26.25 (10.3) 26.25 (10.3)
140 (356) 1.52 (60) 1.52 (60) 188.47 (74) 28.27 (11.1) 28.27 (11.1)
150 (381) 1.63 (64) 1.63 (64) 201.93 (79) 30.29 (11.9) 30.29 (11.9)
12
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 4). They are commercially available from electronics stores.
The connection illustrations below are for reference only. The connecting jacks available on
the projector vary with each projector model.
For detailed connection methods, see pages 14-17.
Below is the connection method for each connector that you may find on your projector.
HDMI
connector A/V device
or
Computer
HDMI cable
HDMI/MHL
connector
MHL dongle
A/V device
or
Computer
HDMI cable
or
LAN
connector
RJ45 cable
Internet
Mini USB
socket
USB cable
Computer
RS232 RS232 cable
Computer
13
(for Component signal)
(for Video signal)
Computer
In
VGA cable
Computer
or
Component Video to VGA
(D-Sub) adapter cable A/V device
Computer
Out
VGA cable
Monitor
or
VGA to DVI-A cable
Audio
in
Audio cable
Computer
Audio cable
A/V device
or
S-Video
connector
S-Video cable
A/V device
Video
connector
Video cable
A/V device
Audio in
L/R
Audio cable
A/V device
Audio Out
Speakers
USB 1.5V
Out USB Power Charger
14
Connecting a computer or monitor
Connecting a computer
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the COMPUTER 1 or COMPUTER 2
signal input socket on the projector.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the COMPUTER OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
1. Connect the projector to a computer as described in "Connecting a computer" on page
14.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the COMPUTER OUT socket on the projector.
The COMPUTER OUT output only works when COMPUTER 1 connection is made to the
projector in the standby mode. To use this connection method, turn on the Active VGA Out
function under the SYSTEM SETUP: Advanced > Standby Settings menu.
(Trigger only)
12V Out
Powered screen
15
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• HDMI
• Component Video
•S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with an HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 15 for how to connect the projector to an HDMI
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 16 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 16 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 16 for how to connect the
projector to a composite Video device.
Connecting audio
You can make use of the projector speaker in your presentations, and also connect separate
amplified speakers to the Audio Out socket of the projector. The audio output is controlled
by the projector Volume and Mute settings.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
1. Take an HDMI cable and connect one end to the HDMI output port of the video
device.
2. Connect the other end of the cable to the HDMI input port on the projector.
16
In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI
input and the projected picture displays wrong colors, please change the color space to YUV.
See "Changing HDMI input settings" on page 22 for details.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
1. Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red
to red.
2. Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub
type connector) to the COMPUTER 1 or COMPUTER 2 socket on the projector.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
1. Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
If you have already made a Component Video connection between the projector and this S-
Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 15 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
1. Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
VGA-Component adapter
(ViewSonic P/N: CB-00008906)
17
You need only connect to this device using a composite Video connection if Component Video
input is unavailable for use. See "Connecting Video source devices" on page 15 for details.
Playing sound through the projector
You can make use of the projector speaker in your presentations, and also connect separate
amplified speakers to the AUDIO OUT socket of the projector.
18
Operation
Starting up the projector
1. Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted).
2. Press Power to start the projector. As soon as
the light source lights up, a "Power On Ring
Tone" will be heard. The Power indicator light
stays blue when the projector is on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the light source.
To maintain the light source life, once you turn the projector on, wait at least 5 minutes before
turning it off.
To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 38 for details.
3. If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press Source to select your desired input signal. See "Switching input
signal" on page 22 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 61 for details.
19
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please select your language first.
1. Press Menu to turn the OSD menu
on.
3. Press to highlight Language and
press Enter.
2. Use / to highlight the
SYSTEM SETUP: Basic menu.
4. Use / / / to select a
preferred language.
5. Press Enter to go back to main
menu and press Menu to leave the
OSD menu.
Current input signal
Main menu icon
Sub-menu
Highlight
Go to the
previous page
or to exit.
Status
20
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 19.
You will be inconvenienced if you enable the password function yet forget the password
somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Setting a password
Once a password has been set and the power on lock is enabled, the projector cannot be used
unless the correct password is entered every time the projector is started.
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings menu.
2. Press Enter and the Security Settings page is displayed.
3. Highlight Change Security Settings and press Enter.
4. As pictured to the right, the four arrow keys
( , , , ) respectively represent 4 digits (1,
2, 3, 4). According to the password you desire to
set, press the arrow keys to enter six digits for the
password.
5. Confirm the new password by re-entering the
new password.
Once the password is set, the OSD menu returns
to the Security Settings page.
6. To activate the Power On Lock function, press
/ to highlight Power On Lock and press / to select On.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right is
displayed lasting for 5 seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not record the password in this user
manual, and you absolutely do not remember it, you can use the password recall procedure.
See "Entering the password recall procedure" on page 21 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
21
Entering the password recall procedure
1. Press and hold Auto Sync on the remote control
for 3 seconds. The projector will display a coded
number on the screen.
2. Write down the number and turn off your
projector.
3. Seek help from the local service center to decode
the number. You may be required to provide
proof of purchase documentation to verify that
you are an authorized user of the projector.
The "XXX" shown in the above screenshot are numbers
that vary depending on different projector models.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Change Password menu.
2. Press Enter. The message 'INPUT CURRENT PASSWORD' is displayed.
3. Enter the old password.
• If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
• If the password is incorrect, the password error message is displayed lasting for
5 seconds, and the message 'INPUT CURRENT PASSWORD' is displayed
for your retry. You can press Exit to cancel or try another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7. To leave the OSD menu, press Exit.
The digits being input will be displayed as asterisks on-screen. Do make a note of your
password, and then keep the note in a safe place for later recall.
Disabling the password function
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Power On Lock menu.
2. Press / to select Off.
3. The message 'INPUT PASSWORD' is displayed. Enter the current password.
• If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
• If the password is incorrect, the password error message is displayed lasting for
5 seconds, and the message 'INPUT PASSWORD' is displayed for your retry.
You can press Exit to cancel or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
22
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by pressing one of the source selection keys
on the remote control, or cycle through the available input signals.
1. Press Source. A source selection bar is displayed.
2. Press / until your desired signal is selected and press Enter.
Once detected, the selected source information will be displayed on the screen for
seconds. If there are multiple devices connected to the projector, repeat steps 1-2 to
search for another signal.
Please see "Projector specifications" on page 65 for the native display resolution of this
projector. For best display picture results, you should select and use an input signal which
outputs at this resolution. Any other resolutions will be scaled by the projector depending
upon the 'aspect ratio' setting, which may cause some image distortion or loss of picture
clarity. See "Selecting the aspect ratio" on page 24 for details.
Changing HDMI input settings
In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray
player) via the projector’s HDMI input and the projected picture displays wrong colors,
please change the color space to an appropriate one that fits the color space setting of the
output device.
To do this:
1. Open the OSD menu and go to the SOURCE > Color Space Invert menu.
2. Press / to select a suitable color space according to the color space setting of the
output device connected.
•Auto: Sets the projector to detect the color space setting of the input signal
automatically.
•RGB Limited Range: Sets the color space as RGB and the HDMI color range
as 15 - 235.
•RGB Full Range: Sets the color space as RGB and the HDMI color range as 0 -
255.
•YUV Limited Range: Sets the color space as YUV and the HDMI color range
as 15 - 235.
•YUV Full Range: Sets the color space as YUV and the HDMI color range as 0
- 255.
This function is only available when the HDMI input port is in use.
Refer to the documentation of the device for information on the color space and HDMI range
settings.
23
Adjusting the projected image
Adjusting the projection angle
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, see "Correcting keystone" on page 23 for details.
Do not look into the lens while the light source is on. The strong light from the light source
may cause damage to your eyes.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press Auto Sync on
the remote control. Within 5 seconds, the built-in Intelligent Auto Adjustment function will
re-adjust the values of Frequency and Clock to provide the best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
The screen will display ViewSonic logo while auto adjustment is functioning.
This function is only available when PC D-Sub input signal (analog RGB) is selected.
Fine-tuning the image clarity
Sharpen the image by rotating the focus
ring.
Correcting keystone
Keystoning refers to the situation where the projected image becomes a trapezoid due to
angled projection.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
• Using the projector or remote control
1. Press / to display the Keystone
correction page.
2. Press to correct keystoning at the top of
the image. Press to correct keystoning at
the bottom of the image.
• Using the OSD menu
1. Open the OSD menu and go to the DISPLAY > Keystone menu.
2. Press Enter.
3. Press to correct keystoning at the top of the image or press to correct
keystoning at the bottom of the image.
Press /
Press /
24
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
• Using the remote control
1. Press on the remote control to display the Zoom bar.
2. Press repeatedly to magnify the picture to a desired size.
3. To navigate the picture, press Enter to switch to the paning mode and press the
directional arrows ( , , , ) to navigate the picture.
4. To reduce size of the picture, you can press Auto Sync on the remote control to
restore the picture to its original size. Or you can press Enter to switch back to the
zoom in/out functionality and press .
• Using the OSD menu
1. Open the OSD menu and go to the DISPLAY > Zoom menu.
2. Press Enter. The Zoom bar is displayed.
3. Repeat steps 2-4 in the section of Using the remote control above.
This adjustable range may vary depending on different aspect ratios.
The picture can only be navigated after it is magnified. You can further magnify the picture
while searching for details.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1. Open the OSD menu and go to the DISPLAY > Aspect Ratio menu.
2. Press Enter.
3. Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
About the aspect ratio
1. Auto: Scales an image proportionally to fit the projector's native resolution in its
horizontal width. This is suitable for the incoming image which is neither in 4:3 nor
16:9 and you want to make most use of the screen without altering the image's aspect
ratio.
2. Real: Projects an image as its original resolution and resizes it to fit within the display
area. For input signals with lower resolutions, the projected image will display smaller
than if resized to full screen.
3. 4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect
ratio. This is most suitable for 4:3 images like computer monitors, standard definition
TV and 4:3 aspect DVD movies, as it displays them without aspect alteration.
4. 16:9: Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like
high definition TV, as it displays them without aspect alteration.
25
5. 16:10: Scales an image so that it is displayed in the center of the screen with a 16:10
aspect ratio. This is most suitable for images which are already in a 16:10 aspect, as it
displays them without aspect alteration.
The table below demonstrates the effects of the aspect ratio settings on projectors with
different native resolutions. Please see "Projector specifications" on page 65 for the native
display resolution of your projector.
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
Optimizing the image
Selecting a color mode
The projector is preset with several predefined color modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
• Press Color Mode to display the selection bar and press / to select a desired mode
or press Color Mode repeatedly.
•Go to the PICTURE > Color Mode menu and press Enter. Press / to select a
desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
1. Bright mode: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required, such as using the projector
in well lit rooms.
2. Dynamic mode: Is designed for presentations under daylight environment to match
PC and notebook coloring. In addition, the projector will optimize the image quality
using the dynamic PC function in accordance with the projected contents.
Aspect ratio setting When the native aspect ratio of your projector is...
4:3
Auto
4:3
16:9
16:10
26
3. Standard mode: Is designed for presentations under daylight environment to match
PC and notebook coloring.
4. sRGB mode: Switches between high brightness performance and accurate color
performance.
5. Movie mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
6. 3D mode: Is appropriate for playing 3D images and 3D video clips.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press Enter. Press /
to select a color which is closest to the color of the projection surface. There are several
precalibrated colors to choose from: Yellow, Greenboard, and Blackboard. The effects of
these settings may vary depending on different models.
This function is only available when a computer input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available.
You can make adjustments to these functions based on your needs.
Adjusting Brightness
Go to the PICTURE > Brightness menu and press Enter.
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
Adjusting Contrast
Go to the PICTURE > Contrast menu and press Enter.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
Adjusting Color
Go to the PICTURE > Color menu and press /.
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
This function is only available when the input signal is S-Video, Video, YPbPr or YCbCr.
Adjusting Tint
Go to the PICTURE > Tint menu and press /.
The higher the value, the more greenish the picture becomes. The lower the value, the more
reddish the picture becomes.
This function is only available when the input signal is S-Video, Video, YPbPr or YCbCr.
50
-30 +80
-30 0+40
27
Adjusting Sharpness
Go to the PICTURE > Sharpness menu and press /.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
This function is only available when the input signal is S-Video, Video, YPbPr or YCbCr.
Adjusting Brilliant Color
Go to the PICTURE > Brilliant Color menu and press /.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select a level that suits your need. If you don’t need it,
select Off.
Selecting a Color Temperature
Go to the PICTURE > Color Temperature menu and press Enter.
The options available for color temperature settings vary according to the signal type
selected.
1. Cool: With the highest color temperature, Cool makes the image appear the most
bluish white than other settings.
2. Normal: Maintains normal colorings for white.
3. Warm: Makes images appear reddish white.
Setting a preferred color temperature
1. Go to the PICTURE > Color Temperature Fine Tuning menu and press Enter.
2. Press / to highlight the item you want to change and adjust the values by
pressing /.
•R Gain/G Gain/B Gain: Adjusts the contrast levels of Red, Green, and Blue.
•R Offset/G Offset/B Offset: Adjusts the brightness levels of Red, Green, and
Blue.
This function is only available when a computer input signal is selected.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1. Open the OSD menu and go to the PICTURE > Color Management menu.
2. Press Enter and the Color Management page is displayed.
3. Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
28
4. Press to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
5. Press to highlight Saturation and adjust
its values to your preference by pressing /
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will
be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6. Press to highlight Gain and adjust its values to your preference by pressing /.
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
7. Repeat steps 3 to 6 for other color adjustments.
8. Make sure you have made all of the desired adjustments.
Resetting current or all picture modes
1. Go to the PICTURE menu and highlight Reset Color Settings.
2. Press Enter and press / to select Current or All.
•Current: returns current color mode to the factory preset settings.
•All: returns all picture modes to the factory preset settings.
RED
BLUE
GREEN
Yellow
Cyan
Magenta
29
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1. Press on the remote control or go to the BASIC > Presentation Timer menu.
2. Highlight Timer Period and decide the time period by pressing /. The length of
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3. Press to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing /.
4. Press to highlight Timer Position and set the timer position by pressing /.
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing /.
6. Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing /. If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
7. To activate the presentation timer, press and press / to highlight Start
Counting and press Enter.
8. A confirmation message displays. Highlight Yes and press Enter to confirm. You will
see the message “Timer is On” displaying on the screen. The timer starts counting
when the timer is on.
To cancel the timer, perform the following steps:
1. Press on the remote control or go to the BASIC > Presentation Timer menu.
2. Highlight Off. Press Enter. A confirmation message displays.
3. Highlight Yes and press Enter to confirm. You will see the message “Timer is Off”
displaying on the screen.
Selection Description
Always Displays the timer on screen throughout the presentation
time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Top-Left Bottom-Left Top-Right Bottom-Right
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decreases from the preset time to 0.
30
Hiding the image
In order to draw the audience's full attention to the presenter, you can press BLANK to hide
the screen image. Press any key on the projector or remote control to restore the image. The
word 'BLANK' appears at the lowe r right corner of the screen while the image is hidden.
You can set the blank time in the BASIC > Blank Timer menu to let the projector return
the image automatically after a period of time when there is no action taken on the blank
screen.
Once Blank is pressed, the projector enters Eco mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except Power.
1. Go to the SYSTEM SETUP: Basic > Panel Key Lock menu
2. Press Enter and press / to select On.
3. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, use the remote control to enter the SYSTEM SETUP: Basic >
Panel Key Lock menu and select Off.
Keys on the remote control are still functional when panel key lock is enabled.
If you press Power to turn off the projector without disabling panel key lock, the projector
will still be in locked status the next time it is turned on.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–30°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1499 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
To activate the High Altitude Mode:
1. Open the OSD menu and go to the SYSTEM
SETUP: Advanced > High Altitude Mode
menu.
2. Press Enter and press / to select On. A
confirmation message is displayed.
3. Highlight Yes and press Enter.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
31
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Using the 3D functions
This projector features 3D function which enables you to enjoy 3D movies, videos, and
sporting events in a more realistic way by presenting the depth of the images. You need to
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from an HDMI 1.4a compatible device and 3D Mode is set as
Auto, the projector projects images in 3D format automatically once detected. In other
cases, you may need to manually select a 3D Mode format for the projector to project 3D
images correctly.
1. Go to the DISPLAY > 3D Settings menu.
2. Press Enter. The 3D Settings page is displayed.
3. Highlight 3D Mode and press Enter.
4. Press to select a 3D Mode setting and then press Enter to confirm.
When the 3D Mode function is on:
• The brightness level of the projected image will decrease.
• The Color Mode cannot be adjusted.
• The Zoom function can only magnify the pictures to limited sizes.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert”
to correct the problem.
Controlling the projector through a LAN
environment
The projector supports Crestron® software. With correct settings for the Wired LAN menu,
you can manage the projector from a computer using a web browser when the computer and
the projector are properly connected to the same local area network.
Configuring the Wired LAN
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port.
2. Open the OSD menu and go to the SYSTEM SETUP: Advanced > LAN Control
Settings > Wired LAN menu.
3. Press Enter. The Wired LAN page is displayed.
(An example of connection)
32
4. Highlight DHCP and press / to select On.
5. Press to highlight Apply and press Enter.
6. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page. The
IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be
displayed. Note down the IP address displayed in the IP Address row.
If the IP Address still does not appear, contact your network administrator.
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default Gateway,
and DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and
perform the procedures above again.
If you need to connect to the projector in its standby mode, set Enable Network Standby Mode
to On in the SYSTEM SETUP: Advanced > Standby Settings > Network menu.
If you are in a non-DHCP environment:
1. Repeat steps 1-3 above.
2. Highlight DHCP and press / to select Off.
3. Contact your ITS administrator for information on the IP Address, Subnet Mask,
Default Gateway, and DNS Server settings.
4. Press to select the item you want to modify and press Enter.
5. Press / to move the cursor and the press / to enter the value.
6. To save the settings, press Enter. If you do not want to save the settings, press Exit.
7. Press to highlight Apply and press Enter.
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default Gateway,
and DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and
perform the procedures above again.
If you wish to connect to the projector in its standby mode, be sure you have set DHCP to Off
and obtained the IP Address, Subnet Mask, Default Gateway, and DNS Server information
when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
The screen shots in this manual are for reference only, and may differ from the actual design.
1. Enter the address of the projector in the address bar of your browser and press Enter.
33
2. The main page of the Network Control appears.
Accessing to Network Settings or Email Alert page requires Administrator password. The
default password is "0000".
3. This page allows you to make adjustments to the AMX and SNMP settings. In the
AMX device discover row, when ON is selected, the projector can be detected by
controllers of AMX connected to the same network. For the Details of AMX Device
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a network which supports Simple Mail Transfer
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See
"About Crestron e-Control®" on page 35 for details.
5
4
3
34
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
/ > < $ % + \ ' " are prohibited.
Category Item Input Length Maximum Number
of Characters
Network Settings
Network
DHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
Password
Administrator (N/A)
New Password 4
Confirm Password 4
SNMP
SysLocation 22
SysName 22
SysContact 22
Email Alert
Email Setting
To 40
Cc 40
Subject 40
From 40
SMTP Setting
Server 30
User Name 21
Password 14
Alert Condition
Fan Error (N/A)
Light source Error (N/A)
Over Temperature (N/A)
Light source Time
Alert (N/A)
Submit (N/A)
Issue Test Mail (N/A)
35
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the
projector or adjust the projected pictures.
i. These buttons function the same as the ones on the OSD menus or remote control.
See "2. PICTURE menu" on page 44 and "Projector" on page 5 for details.
ii. To switch between input signals, click on your desired signal.
The Menu button can also be used to go back to previous OSD menus, exit and save menu
settings.
The source list varies according to the connectors available on the projector.
When you use the projector control panel or remote control to change the OSD menu settings,
it may take a while for the web browser to synchronize these changes with the projector.
2. The tools page allows you to manage the projector, configure the LAN control
settings and secure access of remote network operation on this projector.
i. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of
it.
i
i
i
ii
You can press
/ to
reveal more
buttons.
i iv
iii
ii
v
vi
36
iii. You can adjust the Wired LAN.
iv. Once set, access to the remote network operation on this projector has been
password-protected.
v. Once set, access to the tools page has been password-protected.
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Category Item Input Length Maximum Number of
Characters
Crestron Control
IP Address 16
IP ID 4
Port 5
Projector
Projector Name 32
Location 32
Assigned To 32
Network Configuration
DHCP (Enabled) (N/A)
IP Address 16
Subnet Mask 16
Default Gateway 16
DNS Server 16
User Password
Enabled (N/A)
New Password 26
Confirm 26
Admin Password
Enabled (N/A)
New Password 26
Confirm 26
37
3. The info page displays the information and status of this projector.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in
the upper right corner of the screen. You will be able to deliver messages to
RoomView™ software administrators/users who connect to the same local area
network.
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s
on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron
control port.
About Crestron RoomView™ setting and command method, please access below website to
get RoomView™ User Guide and more information:
http://www.crestron.com/products/roomview_connected_embedded_projectors_devices/
resources.asp
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details,
please follow its user guide or website respectively to control and manage projectors.
Press Exit to
go back to the
remote network
operation page.
38
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure the cable connections are correctly made. For the
connection methods, see the Connection chapter.
Active VGA Out
Selecting On in the SYSTEM SETUP: Advanced > Standby Settings > Active VGA Out
outputs a VGA signal when the COMPUTER 1 and COMPUTER OUT sockets are
correctly connected to devices. The projector outputs the signal received only from
COMPUTER 1.
LAN Control
Making the following settings in the SYSTEM SETUP: Advanced > Standby Settings >
Network allows the projector to provide the network function when it is in standby mode.
See "Controlling the projector through a LAN environment" on page 31 for details.
•Enable Network Standby Mode: Allows the projector to provide the network
function in standby mode.
•Auto Disable Network Standby Mode: Allows the projector to disable the
network function after a set period of time after it enters standby mode. For
instance, if 20 min is selected, the projector is able to provide the network
function for 20 minutes after it enters standby mode. When 20 minutes is up, the
projector enters normal standby mode.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. Be sure
you have made a correct connection to the projector audio input/output jacks. See
"Connection" on page 12 for more details.
Muting the sound
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Audio Settings >
Mute menu.
2. Press / to select On.
If available, you can press on the remote control.
Adjusting the sound level
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Audio Settings >
Volume menu.
2. Press / to select a desired sound level.
If available, you can press / on the remote control to adjust the projector’s sound level.
Turning off the Power On/Off Ring Tone
1. Open the OSD menu and go to the SYSTEM SETUP: Advanced > Audio Settings >
Power On/Off Ring Tone menu.
2. Press / to select Off.
The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.
39
Shutting down the projector
1. Press Power and a confirmation message is
displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
2. Press Power a second time.
3. Once the cooling process finishes, a "Power
Off Ring Tone" will be heard. Disconnect the
power cord from the wall socket if the
projector will not be used in an extended
period of time.
To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 38 for details.
CAUTION
• To protect the light source, the projector will not respond to any commands during the
cooling process.
• Do not unplug the power cord before the projector shutdown sequence is complete.
40
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu Sub-menu Options
1.
DISPLAY
Screen Color Off/Yellow/Greenboard/Blackboard
Aspect Ratio Auto/Real/4:3/16:9/16:10
Keystone
Position
Phase
H. Size
Zoom
3D Settings 3D Mode Auto/Top-Bottom/Frame Sequential/
Frame Packing/Side by Side/Off
3D Sync Invert Disable/Invert
Pattern Off/Test Card/Note Pad/World Map
2.
PICTURE
Color Mode Bright/Dynamic/Standard/sRGB/Movie/
(3D)
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color Off/On
Color
Temperature Warm/Normal/Cool
Color Temperature Fine
Tuning
R Gain/G Gain/B Gain/R Offset/G Offset/
B Offset
Color
Management
Primary Color R/G/B/C/M/Y
Hue
Saturation
Gain
Reset Color Settings Current/All/Cancel
41
Main menu Sub-menu Options
3. SOURCE
Quick Auto Search Off/On
Color Space Invert
Auto/RGB Limited Range/
RGB Full Range/YUV Limited
Range/YUV Full Range
4.
SYSTEM
SETUP:
Basic
Presentation
Timer
Timer Period 1~15~240 m
Timer Display Always/1 min/2 min/3 min/
Never
Timer Position Top-Left/Bottom-Left/Top-
Right//Bottom-Right
Timer Counting
Direction Count Down/Count Up
Sound Reminder On/Off
Start Counting/Off
Language Multi-language OSD
selection
Projector Position Front Table/Rear Table/
Rear Ceiling/Front Ceiling
Menu Settings
Menu Display Time 5 sec/10 sec/20 sec/30 sec/
Always
Menu Position Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Reminder Message On/Off
Operation
Settings
Direct Power On On/Off
Signal Power On Computer
HDMI
Auto Power Off Disable/3 min/10 min/15 min/
20 min/25 min/30 min
Blank Timer Disable/5 min/10 min/15 min/
20 min/25 min/30 min
Sleep Timer Disable/30 min/1 hr/2 hr/3 hr/
4 hr/8 hr/12 hr
Reset Filter Timer Reset/Cancel
Panel Key Lock Off/On
Splash Screen Black/Blue/ViewSonic
42
Main menu Sub-menu Options
5.
SYSTEM
SETUP:
Advanced
High Altitude Mode On/Off
Audio Settings
Mute On/Off
Volume
Power On/Off Ring
Tone On/Off
Light Source Settings Normal/Eco
Security Settings
Change Password
Change Security Settings
Power On Lock Off/On
Baud Rate
2400/4800/9600/14400/
9200/38400/57600/
115200
Closed Caption Closed Caption Enable On/Off
Caption Version CC1/CC2/CC3/CC4
Standby Settings Network
Enable Network
Standby Mode
Auto Disable Network
Standby Mode
Active VGA Out On/Off
LAN Control
Settings
Wired LAN
Status
DHCP
IP Address
Subnet Mask
Default Gateway
DNS Server
Apply
AMX Device Discovery On/Off
MAC Address
Reset All Settings Reset/Cancel
6.
INFORMATION
•Source
•Color Mode
•Resolution
•Color System
•Light Source Usage Time
•IP Address
•MAC Address
• Firmware Version
43
Description of each menu
Function Description
Screen Color See "Using Screen Color" on page 26 for details.
Aspect Ratio See "Selecting the aspect ratio" on page 24 for details.
Keystone See "Correcting keystone" on page 23 for details.
Position
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.
This function is only available when a PC input signal is
selected.
The adjustment range may vary under different timings.
Phase
Adjusts the clock phase to reduce image
distortion.
This function is only available when
a PC input signal is selected.
H. Size
Adjusts the horizontal width of the image.
This function is only available when a PC input signal is
selected.
Zoom See "Magnifying and searching for details" on page 24 for
details.
3D Settings See "Using the 3D functions" on page 31 for details.
Pattern
The projector can display several test patterns. It helps you adjust
the image size and focus and check that the projected image is
free from distortion.
1. DISPLAY menu
44
Function Description
Color Mode See "Selecting a color mode" on page 25 for details.
Brightness See "Adjusting Brightness" on page 26 for details.
Contrast See "Adjusting Contrast" on page 26 for details.
Color See "Adjusting Color" on page 26 for details.
Tint See "Adjusting Tint" on page 26 for details.
Sharpness See "Adjusting Sharpness" on page 27 for details.
Brilliant Color See "Adjusting Brilliant Color" on page 27 for details.
Color
Temperature See "Selecting a Color Temperature" on page 27 for details.
Color
Temperature
Fine Tuning
See "Setting a preferred color temperature" on page 27 for
details.
Color
Management See "Color Management" on page 27 for details.
Reset Color
Settings
Returns the settings of all or current color mode to the factory
preset values.
Quick Auto
Search See "Switching input signal" on page 22 for details.
Color Space
Invert See "Changing HDMI input settings" on page 22 for details.
2. PICTURE menu
3. SOURCE menu
45
Function Description
Presentation
Timer See "Setting the presentation timer" on page 29 for details.
Language Sets the language for the On-Screen Display (OSD) menus.
See "Using the menus" on page 19 for details.
Projector
Position See "Choosing a location" on page 9 for details.
Menu Settings
Menu Display Time
Sets the length of time the OSD will remain active after your
last key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Reminder Message
Sets the reminder messages on or off.
Operation
Settings
Direct Power On
Selecting On allows the projector to turn on automatically
once the power is fed through the power cord.
Signal Power On
Sets whether the projector automatically turns on when the it
is in standby mode and detects a VGA signal or a HDMI
signal with 5V power.
Auto Power Off
Allows the projector to turn off automatically if no input
signal is detected after a set period of time to prevent
unnecessary waste of light source life.
Blank Timer
See "Hiding the image" on page 30 for details.
Sleep Timer
See "Setting Sleep Timer" on page 50 for details.
Reset Filter Timer
See "Resetting the filter timer" on page 49 for details.
Panel Key Lock See "Locking control keys" on page 30 for details.
Splash Screen Allows you to select which logo screen will be displayed
during projector start-up.
4. SYSTEM SETUP: Basic menu
46
Function Description
High Altitude
Mode
A mode for operation in high altitude areas. See "Operating in
a high altitude environment" on page 30 for details.
Audio Settings See "Adjusting the sound" on page 38 for details.
Light Source
Settings See "Setting Light Source Settings" on page 50 for details.
Security
Settings See "Utilizing the password function" on page 20 for details.
Baud Rate
Selects a baud rate that is identical with your computer’s so
that you can connect the projector using a suitable RS232
cable and control the projector with RS232 commands.
Closed Caption
Selects a preferred closed captioning mode when the selected
input signal carries closed captions.
• Captions: An on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are
closed captioned (usually marked as "CC" in TV listings).
This function is only available when a Composite video
input signal is selected and its system format is NTSC.
Caption Version
To view captions, select CC1, CC2, CC3, or CC4 (CC1
displays captions in the primary language in your area).
Standby
Settings
See "Using the projector in standby mode" on page 38 for
details.
LAN Control
Settings
Wired LAN
See "Controlling the projector through a LAN environment"
on page 31 for details.
AMX Device Discovery
When this function is On, the projector can be detected by
AMX controller.
MAC Address
Displays the mac address for this projector.
Reset All
Settings
Returns all settings to the factory preset values.
The following settings will still remain: Keystone,
Projector Position, High Altitude Mode, Security Settings,
Baud Rate, LAN Control Settings.
5. SYSTEM SETUP: Advanced menu
47
Function Description
Current System
Status
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format.
Light Source Usage Time
Displays the number of hours the light source has been used.
IP Address
Shows the IP address of your projector.
MAC Address
Shows the MAC Address of your projector.
MAC Address stands for Media Access Control Address,
which is a physical layer address used to uniquely
identify a network node.
Firmware Version
Shows the current firmware version.
6. INFORMATION menu
48
Maintenance
Care of the projector
You need to keep the lens and/or filter (optional accessory) clean on a regular basis.
Never remove any parts of the projector. Contact your dealer when any part of the projector
needs replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 39 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 54 or
consult your dealer about the range.
• Retract the adjuster foot.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
49
Using the dust filter
CAUTION
• It is recommended to clean the dust filter every 500 hours after the dust filter is installed.
• Be sure to turn off the projector and unplug it from power source before installing or
detaching the filter.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to
your personal safety when replacing the dust filter.
Replacing the dust filter
1. Be sure to turn off the projector and unplug it from power source.
2. Locate the dust filter cover on the side of the projector and loosen the 4 screws using
the screwdriver. Keep the screws in a safe place for later use. Detach the dust filter
cover from the projector.
3. Replace the old (used) filter in the dust filter cover with the spare (new) filter .
Dispose of the old filter properly according to your local regulations.
4. Re-install the dust filter cover using the screwdriver and the screws removed in step 2.
Resetting the filter timer
5. Open the OSD menu and go to the SYSTEM SETUP: Basic > Operation Settings
menu.
6. Press Enter and the Operation Settings page is displayed.
7. Highlight Reset Filter Timer and press Enter. A warning message is displayed
asking if you want to reset the filter timer.
8. Highlight Reset and press Enter. The light source time will be reset to '0'.
50
Light source information
Extending light source life
The projection light source is a consumable item. To keep the light source life as long as
possible, you can do the following settings via the OSD menu.
Setting Light Source Settings
Setting the projector in Eco mode reduces system noise, power consumption and extends
the light source operation life.
To set the Light Source Settings, go to the SYSTEM SETUP: Advanced > Light Source
Settings menu and press / to select. Or you can press Eco Mode on the remote control
to select.
Setting Auto Power Off
This function allows the projector to turn off automatically after a set period of time once no
input source is detected to prevent unnecessary waste of light source life.
1. Open the OSD menu and go to the SYSTEM SETUP: Basic > Operation Settings
menu.
2. Press Enter and the Operation Settings page is displayed.
3. Highlight Auto Power Off and press /.
4. If the preset time lengths are not suitable for your need, select Disable. The projector
will not automatically shut down in a certain time period.
Setting Sleep Timer
This function allows the projector to turn off automatically after a set period of time to
prevent unnecessary waste of light source life.
1. Open the OSD menu and go to the SYSTEM SETUP: Basic > Operation Settings
menu.
2. Press Enter and the Operation Settings page is displayed.
3. Highlight Sleep Timer and press / .
4. If the preset time lengths are not suitable for your presentation, select Disable. The
projector will not automatically shut down in a certain time period.
Light
source
mode
Description
Normal Provides full light source brightness.
Eco Reduces light source power consumption by 30% and lowers brightness
to extend the light source life and decreases the fan noise.
51
Timing of replacing the light source
Please install a new light source or consult your dealer when the Light source indicator
light lights up. An old light source may cause a malfunction in the projector and in some
instances the light source may explode.
CAUTION
The Light source indicator light and Temperature indicator light will light up if the light source
becomes too hot. Turn the power off and let the projector cool for 45 minutes. If the Light
source indicator light or Temperature indicator light still lights up after turning the power back
on, please contact your dealer. See "Indicators" on page 52 for details.
Replacing the light source
Turn the power off and disconnect the projector from the power outlet. Please contact
qualified service personnel for changing the light source.
52
Indicators
Light Status & Description
Power events
Orange Off Off Stand-by mode
Green
Flashing Off Off Powering up
Green Off Off Normal operation
Orange
Flashing Off Off Normal power-down cooling
Red Flashing Red
Flashing
Red
Flashing Download
Green Off Red CW start fail
Red Flashing Off Off Scaler shutdown fail (data abort)
Red Off Red Scaler reset fail (video projector only)
Green Off Off Burn-in ON
Green Green Green Burn-in OFF
Light source events
Off Off Red Light source error in normal operation
Off Off Orange
Flashing Light source is not lit up
Green Off Orange Light source life exhausted
Thermal events
Red Red Off Fan 1 error (the actual fan speed is outside the
desired speed)
Red Red
Flashing Off Fan 2 error (the actual fan speed is outside the
desired speed)
Red Green Off Fan 3 error (the actual fan speed is outside the
desired speed)
Red Green
Flashing Off Fan 4 error (the actual fan speed is outside the
desired speed)
Green Red Off Temperature 1 error (over limited temperature)
Green Red
Flashing Off Thermal Sensor 1 open error
Green Green Off Thermal Sensor 1 short error
Green Green
Flashing Off Thermal IC #1 I2C Connection error
Green
Flashing
Green
Flashing Off Thermal IC #2 I2C Connection error
Green Red Red Thermal break error
53
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
Cause Remedy
There is no power from the power cord.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the power
outlet. If the power outlet has a switch, make sure
that it is switched on.
Attempting to turn the projector on again
during the cooling process. Wait until the cooling down process has completed.
Cause Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the signal
cable is connected correctly.
The projector is not correctly connected to
the input signal device. Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the Source key
on the projector or remote control.
Cause Remedy
The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as well as
the height of the projector if necessary.
Cause Remedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the remote
control and the projector. Remove the obstacle.
You are too far away from the projector. Stand within 8 meters (26 feet) from the projector.
54
Specifications
Dimensions
415.5 mm (W) x 149.6 mm (H) x 298 mm (D) (Including extrusions)
Ceiling mount installation
298
415.5
149.6
Unit: mm
207.6
76.5
77
199.6
8
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
55
IR control table
Key Format Byte1 Byte2 Byte3 Byte4
Freeze NEC83F403FC
Blank NEC83F407F8
Auto sync NEC83F408F7
Up NEC 83 F4 0B F4
Down NEC 83 F4 0C F3
Left NEC 83 F4 0E F1
Right NEC 83 F4 0F F0
Color Mode NEC 83 F4 10 EF
Aspect Ratio NEC 83 F4 13 EC
Mute NEC83F414EB
Enter NEC 83 F4 15 EA
Power ON NEC 83 F4 17 E8
3D NEC83F420DF
Presentation Timer NEC 83 F4 27 D8
Exit NEC 83 F4 28 D7
D. ECO
(Eco mode) NEC 83 F4 2B D4
Menu NEC83F430CF
Magnify + NEC 83 F4 32 CD
Source NEC83F440BF
COMP1 NEC 83 F4 41 BE
COMP2 NEC 83 F4 45 BA
Pattern NEC 83 F4 55 AA
HDMI NEC 83 F4 58 A7
Volume+ NEC 83 F4 82 7D
Volume- NEC 83 F4 83 7C
Informaiton NEC 83 F4 97 68
Video NEC 83 F4 9F 60
56
RS232 command table
<Pin assignment for this two end>
<Interface>
<RS232 command table>
Pin Description Pin Description
1NC2RX
3TX4NC
5GND6NC
7RTSZ8CTSZ
9NC
RS-232 protocol
Baud Rate 115200 bps (default)
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
Function Status Action cmd
Power
Write
Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Read Power status
(on/off) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00
0x5E
High
Altitude
Mode
Write
High Altitude
Mode Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High Altitude
Mode On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
Read High Altitude
Mode status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C
0x6A
Light source
Mode
Write
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Read Light source
Mode status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10
0x6E
Projector
Position
Write
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Read projector
position status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00
0x5F
57
3D Sync
Write
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x00 0x8F
Top-Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x01 0x90
Frame
Sequential 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x02 0x91
Frame
Packing 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x03 0x92
Side-by-Side 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x04 0x93
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x05 0x94
Read 3D Sync
Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x32
0x90
Contrast
Write
Contrast
decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast
increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Read Contrast ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02
0x61
Brightness
Write
Brightness
decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness
increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Read Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03
0x62
Aspect ratio
Write
Aspect ratio
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio
Real 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x01 0x63
Aspect ratio
4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio
16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio
16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Read Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04
0x63
Auto Adjust Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
58
Color
temperature
Write
color
temperature
Cool 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
color
temperature
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
color
temperature
Warm 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
Read color
temperature
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08
0x67
Blank
Write
Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09
0x68
Color mode
Write
Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Dynamic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
sRGB (or
ViewMatch
sRGB ) 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
3D 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Read Color mode
status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B
0x6A
Freeze
Write
Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00
0x60
59
Source
input
Write
Input source
D-Sub / Comp.
10x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Input source
D-Sub / Comp.
20x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x01 0x61
Input source
HDMI 1 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Input source
HDMI 2/MHL 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Input source
Video 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x04 0x64
Input source
S-Video 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Read Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01
0x61
Quick Auto
Search
Write
Quick Auto
Search on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto
Search off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Read Quick Auto
Search status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02
0x62
Mute
Write
Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Read Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00
0x61
Volume
Write
Increase
Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Decrease
Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03
0x64
Light source
Time
Write Reset light
source usage
hour 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Read Light source
usage hour 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01
0x63
Brilliant
Color
Write
Brilliant Color
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D
Brilliant Color
On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E
Read Brilliant Color
status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0F
0x6E
60
Remote Key Write
Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61
Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D
Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E
Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F
Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60
Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56
Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67
Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x08 0x5A
61
Timing chart
Analog RGB
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
VGA 640 x 480 4:3 60/72/75/85
SVGA 800 x 600 4:3 60/72/75/85
XGA
1024 x 768 4:3 60/70/75/85
1152 x 864 4:3 75
WXGA
1280 x 768 15:9 60
1280 x 800 16:10 60/75/85
1360 x 768 16:9 60
Quad-VGA 1280 x 960 4:3 60/85
SXGA 1280 x 1024 5:4 60
WXGA 1366 x 768 16:9 59.7
SXGA+ 1400 x 1050 4:3 60
WXGA+ 1440 x 900 16:10 60
UXGA 1600 x 1200 4:3 60
WSXGA+ 1680 x 1050 16:10 60
HD 1280 x 720 16:9 60
MAC 13" 640 x 480 4:3 67
MAC 16" 832 x 624 4:3 75
MAC 19" 1024 x 768 4:3 75
MAC 21" 1152 x 870 4:3 75
HDTV (1080p) 1920 x 1080 16:9 60
62
HDMI
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
VGA 640 x 480 4:3 60
SVGA 800 x 600 4:3 60
XGA 1024 x 768 4:3 60
WXGA
1280 x 768 15:9 60
1280 x 800 16:10 60
1360 x 768 16:9 60
Quad-VGA 1280 x 960 4:3 60
SXGA 1280 x 1024 5:4 60
WXGA 1366 x 768 16:9 59.7
SXGA+ 1400 x 1050 4:3 60
WXGA+ 1440 x 900 16:10 60
WSXGA+ 1680 x 1050 16:10 60
HDTV (1080p) 1920 x 1080 16:9 50 / 60
HDTV (1080i) 1920 x 1080 16:9 50 / 60
HDTV (720p) 1280 x 720 16:9 50 / 60
SDTV (480p) 720 x 480 4:3 / 16:9 60
SDTV (576p) 720 x 576 4:3 / 16:9 50
SDTV (480i) 720 x 480 4:3 / 16:9 60
SDTV (576i) 720 x 576 4:3 / 16:9 50
63
3D (HDMI signal included)
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
SVGA 800 x 600 4:3 60* / 120**
XGA 1024 x 768 4:3 60* / 120**
HD 1280 x 720 16:9 60* / 120**
WXGA 1280 x 800 16:9 60* / 120**
for Video Signal
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
SDTV (480i)*** 720 x 480 4:3 / 16:9 60
*
50Hz and 60Hz signals are supported for
Side-by-Side
,
Top-Bottom
, and
Frame
Sequential
formats.
** 120 Hz signals are supported for Frame Sequential format only.
*** Video signal (SDTV 480i) is supported for Frame Sequential format only.
HDMI 3D
In Frame packing format
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080p 1920 x 1080 16:9 23.98/24
720p 1280 x 720 16:9 50/59.94/60
In Side by side format
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080i 1920 x 1080 16:9 50/59.94/60
720p 1280 x 720 16:9 50/59.94/60
In Top and Bottom format
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080p 1920 x 1080 16:9 23.98/24
720p 1280 x 720 16:9 50/59.94/60
64
Component video
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
HDTV (1080p) 1920 x 1080 16:9 50 / 60
HDTV (1080i) 1920 x 1080 16:9 50 / 60
HDTV (720p) 1280 x 720 16:9 50 / 60
SDTV (480p) 720 x 480 4:3 / 16:9 60
SDTV (576p) 720 x 576 4:3 / 16:9 50
SDTV (480i) 720 x 480 4:3 / 16:9 60
SDTV (576i) 720 x 576 4:3 / 16:9 50
Composite video
Signal Aspect Ratio Refresh Rate (Hz)
NTSC 4:3 60
PAL 4:3 50
PAL60 4:3 60
SECAM 4:3 50
65
Projector specifications
All specifications are subject to change without notice.
Not all models can be purchased in your region.
Product Specification
Resolution 0.55” XGA (1024 x 768)
Throw ratio 0.61
Display system 1-CHIP DMD
Light source LASER DIODE NUBM08 8pcs x 2
Input connector
RGB-in 2
Component input shared with RGB-in
S-Video 1
Composite input 1
Audio-in 1
RCA R&L 1
Mini USB 1 (firmware upgrade)
HDMI (1.4a) 1
HDMI/MHL
1
Output connector
RGB-out 1
USB-A 1 (provide power supply)
Audio-out 1
Speaker 10 watt x 2
Control terminal
RS-232 serial control 9 pin x 1
LAN RJ45 x 1
IR receiver 2 (Front; rear)
12V trigger 1
Mechanical
Net Weight 5.6 Kg (12.3 lbs)
Electircal
Power Source AC100–240V, 50–60 Hz
Power Consumption STD: 305 W (Max); < 0.5 W (Standby)
Environmental Requirements
Operating Temperature 0°C–40°C at sea level
Operating Altitude 0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C
(with High Altitude Mode on)
Operating Relative Humidity 10%–90% (without condensation)
66
Copyright information
Copyright
Copyright © 2017. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region Website T= Telephone
C = CHAT ONLINE Email
Australia
New Zealand www.viewsonic.com.au AUS= 1800 880 818
NZ= 0800 008 822 service@au.viewsonic.com
Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com
Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com
India www.in.viewsonic.com T= 1800 419 0959 service@in.viewsonic.com
Korea ap.viewsonic.com/kr/ T= 080 333 2131 service@kr.viewsonic.com
Latin America
(Argentina) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Chile) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Columbia) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Mexico) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.
Tel: 55) 6547-6454 55)6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico
Latin America
(Peru) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Macau www.hk.viewsonic.com T= 853 2840 3687 service@hk.viewsonic.com
Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com
Puerto Rico &
Virgin Islands www.viewsonic.com
T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/
la/soporte/servicio-tecnico
service.us@viewsonic.com
soporte@viewsonic.com
Singapore/
Malaysia/Thailand www.ap.viewsonic.com T= 65 6461 6044 service@sg.viewsonic.com
South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com
United States www.viewsonic.com T= 1-800-688-6688 service.us@viewsonic.com
67
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
IRUODERUDQGRQH\HDUIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHU
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
RULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH(XURSH2QH\HDU
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days
IRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH
Other regions or countries: Please check with your local dealer or local ViewSonic
RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWR
manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration, failure, or malfunction resulting from:
D$FFLGHQWDEXVHPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUH
LPSURSHUPDLQWHQDQFHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRUIDLOXUHWRIROORZ
instructions supplied with the product.
E2SHUDWLRQRXWVLGHRISURGXFWVSHFL¿FDWLRQV
c. Operation of the product for other than the normal intended use or not under
normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
J&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH
K8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
68
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
FRQWDLQHGKHUHLQLQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUD
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
XSRQLQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRI
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWV
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
69
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of
WKH¿UVWFRQVXPHUSXUFKDVH
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration or malfunction resulting from:
D$FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFW
PRGL¿FDWLRQXQDXWKRUL]HGDWWHPSWHGUHSDLURUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHGZLWKWKH
product.
b. Any damage of the product due to shipment.
F&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH
G8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
LQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
70
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
7HO(QJOLVK6SDQLVK
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
71
