Viewsonic LS820 User Manual
Displayed below is the user manual for LS820 by Viewsonic which is a product in the Data Projectors category. This manual has pages.
Related Manuals
LS810/LS820/LS830
DLP Projector
User Guide
Model No. VS16500/VS16501/VS16460
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specic languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the follow-
ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Lead in glass of cathode ray tubes.
2. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
3. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
4. Copper alloy containing up to 4% lead by weight.
5. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
6. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
iv
Copyright Information
Copyright © ViewSonic® Corporation, 2016. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specications without notice. Information in this docu-
ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name: LS810/LS820/LS830
ViewSonic DLP Projector
Model Number: VS16500/VS16501/VS16460
Document Number: LS810/LS820/LS830_UG_ENG Rev. 1A 06-21-16
Serial Number: ________________________________________
Purchase Date: ________________________________________
Product disposal at end of product life
The lightsource in this product contains mercury which can be dangerous to you and
the environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
Table of Contents
Key safety instructions ....1
Introduction .......................3
Projector features ...................................... 3
Shipping contents ...................................... 4
External appearance of the projector ........ 5
Device control and functions .................... 6
Projector Positioning .....12
Choosing a location ................................. 12
Projection Dimension............................... 13
Connection ......................14
Connect to the computer or monitor ........ 15
Connecting to Video source devices ....... 16
Connecting to HDMI devices ................... 17
To connect the projector to a Component
Video source device: ............................... 17
To connect the projector to a S-Video
source device: ......................................... 17
Connecting to composite video source
devices .................................................... 18
Audio playback with the projector ............ 18
Operation .........................19
Activate the projector ............................... 19
Using the menus...................................... 19
Disabling the password function .............. 21
Setting a password .................................. 21
If you forget your password ..................... 21
Entering the password recall procedure .. 22
Change Password ................................... 22
Disabling the password function .............. 22
Switching input signal .............................. 23
Changing HDMI input settings ................. 24
Adjusting the projected image ................. 25
Correcting keystone................................. 26
Adjusting the 4 corners ............................ 27
Zoom out for detailed review ................... 28
Selecting the aspect ratio ........................ 28
About the aspect ratio.............................. 29
Optimizing the image ............................... 30
Using Screen Color ................................. 30
Fine-tuning of image quality in user
modes ...................................................... 31
Setting the Presentation Timer ................ 34
Hiding the image...................................... 35
Locking control keys ................................ 35
Creating your own startup screen............ 36
Operations at high altitudes ..................... 36
Using the CEC function ........................... 37
3D functions............................................. 37
Using the projector under standby mode 37
Adjusting the sound ................................. 38
Switch off the projector ............................ 38
Menu operations ...................................... 39
Description of each menu ........................ 42
Maintenance ....................47
Care of the projector ................................ 47
Using the lter.......................................... 48
LED Indicator ........................................... 49
Troubleshooting .............50
Specications .................51
Projector specications............................ 51
Dimensions .............................................. 52
Ceiling mount installation......................... 52
Timing chart ............................................. 53
Copyright information ....57
Copyright ................................................. 57
Disclaimer ................................................ 57
Appendix .........................58
IR control table ........................................ 58
Address Code .......................................... 59
RS232 command table ............................ 59
11
Key safety instructions
Design and testing of your projector have been carried out in compliance with the
latest safety standards for information technology (IT) devices. However, it is extremely
important for you to follow the instructions provided in this manual and product labels
during use to ensure user safety.
Safety Instructions
•Please read through this manual before using the projector. Save it for future
reference.
•Do not look directly into the projector lens during use. The intense light beam
may damage your eyes.
•Referservicingtoqualiedservicepersonnel.
•Always open the lens shutter or remove the lens cap when the projector light
source has been switched on.
• Stable line voltage may not be available in certain countries. This projector is designed
to operate safely within a mains voltage between 100 to 240 volts AC, but could fail
if power cuts or surges of ±10 volts occur. In areas where the mains voltage may
uctuateorcutout,itisrecommendedthatyouconnectyourprojectorthrough
apowerstabilizer,surgeprotectororuninterruptiblepowersupply(UPS).
• Do not block the projection lens with any object when using the projector as this could
cause the said objects to overheat, deform, or even cause a re. To temporarily turn
off the light source, press the [BLANK] button on the projector or remote control.
• Do not place the projector on an unstable cart, stand, or table. The product may fall
and sustain serious damages.
• Do not attempt to disassemble this projector. The projector contains high voltage parts
that may cause electrocution or death when it comes in contact with the human body.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing to qualied service personnel.
• Do not place the projector in any of the following environments.
- Space that is poorly ventilated or conned. Allow at least 50 cm clearance from
walls and ensure free ow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of
a car with all windows rolled up.
- Locations that are too humid, dusty, or smoky may contaminate optical
components, shortening the projector's life span and darkening the image.
- Locations near re alarms
- Locations where temperature exceed 35°C/104°F.
- Locations with altitudes greater than 3000 m (10000 feet).
2
• Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a re.
- Do not place this projector on a blanket, bedding, or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inammables near the projector.
• Do not step on the projector or place any object upon it. These acts may damage the
projector itself as well as cause accidents or personal injury.
• Do not place liquids near or on the projector. Liquids spilled into the projector may
cause damage. If the projector does become wet, please unplug the power cable from
the power socket and contact your local repair center for repairs.
• This product can be mounted on a ceiling suspension mount for back projection.
Use only ceiling suspension mounts that comply with the relevant requirements and
ensure that the installation is secure.
• When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. This is a normal phenomenon and not a product defect.
• Do not use the safety lever during transport or installation purposes. The safety lever
should only be used with the anti-theft cables sold on the market.
Safety instructions for ceiling mounting of the projector
We hope you to have a pleasant user experience with our projector. This is why we’re
bringing these safety reminders to your attention to prevent possible damage to person
and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
suitable projector ceiling mount kit and ensure it is securely and safely installed.
There may be safety risks if you fail to use an appropriate projector ceiling mounting kit.
Use of inappropriate connectors or screws of the wrong specications or length may cause
the projector to fall from the ceiling.
You can purchase a projector ceiling mounting kit from the projector dealer. We
recommend buying a safety harness in addition to the mounting kit. The harness should be
securely connected to the anti-theft locking groove on the projector as well as the base of
the ceiling mounting support. This will provide additional protection in case the connectors
of the mounting support becoming loose.
3
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
• Presentation Timer offers better time management during presentations
• 3D Display supported
• Color Management allows you to adjust colors according to your preferences
• Screen Color Correction allows projection on surfaces with various pre-dened colors
• Quick auto search speeding up the signal detecting process
• Color mode provides different options designed for different projection purposes
• Select Fast Shutdown
• Digital Keystone Correction and 4 Corner Adjustments (available for selected models)
can help correct distorted images.
• Provides Color Management adjustments for digital / video displays
• Capable of displaying 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Compatible with Component HDTV (YPbPr)
• HDMI Consumer Electronics Control (CEC) allows synchronized power activation
/ shutdown operations when the projector is connected to a CEC-compatible DVD
player or device via the HDMI input jack
The apparent brightness of the projected image will vary depending on ambient lighting
conditions,andselectedinputsignalcontrast/brightnesssettings.Brightnessisalsodirectly
proportional to projection distance.
4
Shipping contents
Carefully unpack the product and check that you have all of the items shown below. If
any of these items are missing, please contact the dealer from whom you’ve purchased
this projector.
Standard accessories
Thesuppliedaccessorieswillbesuitableforyourregion,andmaydifferfromthoseillustrated.
Projector Power cable
1
LS810/LS820/LS830
DLP Projector
Quick Start Guide
2 3
COMP1COMP2HDMI
Source
Enter
Menu3D Exit
PgUp
MousePatternBlank
PgDn
Eco
Mode Color
Mode
Auto
Sync
3
COMP1 COMP2HDMI
Source
Enter
Menu 3D Exit
PgUp
Mouse
Pattern
Blank
PgDn
Eco
Mode
Color
Mode
Auto
Sync
5
COMP1COMP2HDMI
Source
Enter
Menu3D Exit
PgUp
MousePatternBlank
PgDn
Eco
Mode Color
Mode
Auto
Sync
COMP1 COMP2HDMI
Source
Enter
Menu 3D Exit
PgUp
Mouse
Pattern
Blank
PgDn
Eco
Mode
Color
Mode
Auto
Sync
4
1
2
ViewSonic
VGA cable Multi-language user manual CD Quick Start Guide
Remote control battery HDMI Cable
5
External appearance of the projector
Front / rear
Side
Top / bottom
Warning
• This equipment must be connected to ground.
• Youmayaddpowerinterruptiondevicesinthexedwiringorpluginthepowercabletoanearbysocketfor
convenience.Iffailuresorerrorsoccurduringequipmentoperations,usethepowerinterruptiondevicetocut
the power or unplug the power cable from the socket.
6
Device control and functions
projector
1. (MYBUTTON)
Allows the user to dene buttons and hotkeys. These functions can be set using the
OSD menu.
2. STATUS LED
3. / / / (KeystoneCorrectionbuttons)
Manually corrects distorted images resulting from an angled projection.
Left/Right/Up/Down
Selects the required menu item to make adjustments.
4. POWER LED
5. (POWER)
Toggles the projector between standby mode and Power ON.
6. MENU/EXIT
Open the OSD menu.
7. ENTER
Enacts the selected On-Screen Display (OSD) menu item.
Displays the Corner Adj. page.
8. SOURCE
Shows the Source Selection Bar.
7
Remote Control
To use the remote mouse cursor control
buttons(PageUp,PageDown, and ),
please refer to “Using the remote control
cursor” for more details.
1. Power
Switches the projector between
Standby and ON modes.
2. Signal Selection button.
• COMP
Select the signal source for the D-Sub/
Comp. display.
• VIDEO
Select the source of the Video
displayed.
• HDMI/MHL
Select the source of the HDMI/MHL
displayed.
3. Auto Sync
Automatically veries the best picture
quality for the image displayed.
4. / / / (KeystoneCorrection
buttons)
Manually corrects distorted images
resulting from an angled projection.
Left/Right/Up/Down
Selects the required menu item to make
adjustments.
5. Enter
Enacts the selected On-Screen Display
(OSD) menu item.
6. Menu
Open the OSD menu.
7. (LeftMouseButton)
Once Cursor Mode has been activated,
this key would have the same function
as the Left Mouse Button.
Only available when PC input signals were
selected.
8. (RightMouseButton)
Once Cursor Mode has been activated,
this key would have the same function
as the Right Mouse Button.
Only available when PC input signals were
selected.
9. Mouse
Switch between Normal and Cursor
Mode.
PgUp, PgDn, , : Activated by
pressing the [Mouse] button. The
screen will display an icon that indicates
Cursor Mode has been activated.
Only available when PC input signals were
selected.
8
10. (PanelKeyLock)
To disable Panel Key Lock after it has
been activated, please press .
11. (PresentationTimer)
Brings up the Presentation Timer
settings menu.
12. (Volume)
Brings up the Volume Slider
13. Eco Mode
Select light source Mode.
15. (MyButtons)
Allows the user to dene hotkeys on the
remote control. These functions can be
set using the OSD menu.
16. Source
Shows the Source Selection Bar.
17. Laser
Emits a visible laser pointer
beam which can be used during
presentations.
18. Exit
Goes back to the previous OSD menu.
Exits and saves menu settings.
19. PgUp(PageUp)/PgDn(PageDown)
Can be used to operate the displayed
software (Microsoft PowerPoint)
running on the connected computer.
When Cursor Mode is activated, these
buttons will refer to the Previous Page
and Next Page functions.
Only available when PC input signals were
selected.
20. Pattern
Shows the inbuilt testing screens.
21. Blank
Hide screen image.
22. (Help)
Brings up the Help menu.
23. (Mute)
Toggles the projector audio between on
and off.
24. (Zoom)
Brings up the Zoom Bar which can be
used to magnify or shrink the projected
image.
25. Color Mode
Selects an available Picture Setup
mode.
26. Audio Mode
Selects an Audio mode.
27. Focusing ring
Adjusts the focus of the projected
image.
28. (Aspectratio)
Displays the aspect ratio selection bar.
9
Use the laser pointer.
The laser pointer is a professional tool for supporting presentations. Press this button to
emit a colored laser pointer beam. The laser beam emitted is within the visible spectrum.
To generate the pointer beam continuously, press and hold the [Laser] button.
Do not look at the laser light and do not aim the laser beam at yourself or other people. Please
read the warning texts provided at the back of the remote control before use.
The laser pointer is not a toy. Parents should be aware of the hazards posed by laser
energy and place the remote at a location not accessible to children.
Remote control code
The projector is capable of having 8 different remote control codes (1 to 8). When using
multiple projectors close to each other at the same time, switching the remote control
codes will prevent projector disruption by other remote controls. First set the projector’s
remote control code then switch the code of the remote control itself.
If you want to switch the code at the projector end, please go to System Settings:
Remote Control Code menu and select 1 to 8.
If you want to switch the code at the remote control
end, please press and hold both the [ID set] and
number key corresponding to the remote control code
for at least 5 seconds. 1 is the initial code by default.
Setting the code to 8 allows the remote control to
control every projector.
The projector will not respond to commands issued by the remote control commands if the
projectorandremotecontrolcodesarenotthesame.Whenthishappens,amessagewill
appear to remind you to switch the remote control code.
10
Using the remote control cursor
Use the remote control to operate your computer during presentations for greater exibility
1. Before using the remote control to replace your cursor, x one end of the USB cable
to the projector Mini USB port and the other end to the PC or notebook computer.
See “Connect to the computer” for details.
2. Change the input signal to D-Sub or HDMI via PC source.
3. Press the [Mouse] button on the remote control to switch from Normal Mode to
Cursor Mode. The screen will display an icon that indicates Cursor Mode has been
activated.
4. Achieve mouse cursor functions through using your remote.
• To move the cursor on screen, please press ///.
• To make a single click with the Left Mouse Button, please press .
• To make a single click with the Right Mouse Button, please press .
• To use the displayed software (such as Microsoft PowerPoint) of the connected
computer, press PgUp/PgDn to go to the previous page or the next page.
• To return to Normal mode, press the [Mouse] button again or press other functional
buttons not related to the mouse functions.
Remote control effective range
There is an infra-red (IR) remote control sensor located at the front of the projector. Hold
the remote control and maintain a perpendicular angle within 30 degrees with the IR
remote control sensor to achieve normal remote control functions. The distance between
the remote control and the sensor should not exceed 8 meters (about 26 feet).
Do not place any obstruction in front of the IR sensor
on the projector as this may block the IR beam.
Approx. 30°
11
Replacing the remote control battery
1. To open the battery cover, place the remote control with the backside facing upwards.
Press down at the indicated area and then pull the battery lid upwards along the indi-
cated direction.
2. Take out the old batteries (if required) and then place 2 AAA batteries according to
the indicated orientation. The positive pole of the battery should be directed at the (+)
direction while the negative pole should be directed at the direction.
3. Align the battery lid with the bottom part of the remote control and push downwards.
Return the lid to its original position to complete the process.
Warning
• Avoidplacingtheremotecontrolandbatteryinhotandhumidenvironmentssuchaskitchens,bathrooms,
saunas,tanningrooms,orwithinvehicles.
• Replace batteries only with the same or equivalent type of batteries recommended by the battery
manufacturer.
• Refer to the manufacturer’s instructions and local environmental regulations to dispose of old batteries.
• Donotthrowbatteriesintores.Theremaybedangerofanexplosion.
• Ifthebatteryisatorifyouwillnotbeusingtheremotecontrolforawhile,removethebatterytoprevent
battery leaks from damaging the remote control.
12
Projector Positioning
Choosing a location
You may refer to the room layout or personal preference to determine the location of
installation. Considerations include size and position of the screen, location of a suitable
power outlet, as well as the location and distance between the projector and other
equipment.
There are 4 potential installation locations for the projector:
1. Front Table
For this location, the projector is placed right in front of the
screen. This is the most commonly employed means for
placing the projector. It is quick to setup and highly mobile.
2. Front Ceiling
For this location, the projector is suspended upside-down
from the ceiling in front of the screen.
Purchase a Projector Ceiling Mounting Kit from your dealer
to mount your projector on the ceiling.
After activating your projector, go to System Settings:
Projector Position menu and set to Front Ceiling.
3. Rear Ceiling
For this location, the projector is suspended upside-down
from the ceiling behind the screen.
Note that a special rear projection screen and Projector
Ceiling Mounting Kit are required for this installation
location.
After activating your projector, go to System Settings:
Projector Position menu and select Rear Ceiling.
4. Rear Table
For this location, the projector is placed right behind the
screen.
Note that a special rear projection screen is required.
After activating the projector, go to System Settings:
Projector Position menu and select Rear Table.
13
Projection Dimension
Screens mentioned in the following section refer to projection screens composed of a screen
surface and supporting structures.
(W)
(H)
(a)
(b)
Distance from the center of the glass lens to the bottom peg: 115 mm
1080P Unit: mm Corresponding model: LS820 LS830
Diagonal L a b Screen width w Screen height H
80" 209.6 405 1771 996
86" 229.4 442 1904 1071
90" 238^6 463 1992 1121
93" 248.0 481 2059 1158
100" 267.8 521 2214 1245
110" 296.8 577 2435 1370
120" 325.8 632 2657 1495
130" 346.9 692 2879 1619
140" 376.0 744 3099 1743
150" 404.0 800 3321 1868
WXGA Unit: mm Corresponding model: LS810
Diagonal L a b Screen width w Screen height H
80" 188.92 411 1723 1077
86" 204.89 443 1852 1158
90" 215.54 465 1939 1212
93" 221.02 483 2003 1252
100" 238.95 519 2154 1346
103" 245.64 536 2219 1387
110" 266.77 578 2369 1481
120" 291.39 631 2585 1615
130" 314.00 687 2800 1750
140" 336.62 737 3015 1885
150" 362.23 791 3231 2019
** These gures are for reference purposes only. Refer to the actual projector for the precise dimensions.
14
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all devices off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are rmly inserted.
Intheconnectionsshownbelow,somecablesmaynotbeincludedwithintheprojector
packaging(pleasereferto“Shipping contents”).
You may purchase the required signal cables from an electronics store.
The following links and icons are for references only. Connection jacks at the back of the
projectors may differ according to the projector model.
Display
AV Device
Notebook or
desktop
computer
Speakers
Microphone
(VGA) or
or
(DVI)
1. Computer In
2. Computer Out
3. Mini USB
4. Component
5. S-Video
6. Video
7. Audio
8. HDMI + USB 5V/2A Out
9. HDMI + Micro USB
10. MHL
15
Connect to the computer or monitor
Connect to the computer
1. Use the VGA cable provided. Plug one end to the D-Sub output jack at the com-
puter end.
2. Connect the other end of the VGA cable to the COMPUTER IN1 or IN2 signal
input jack on the projector.
3. To use the remote mouse cursor control function, plug in the larger end of the
USB cable to the USB port on the computer and the smaller end to the MINI
USB jack on the projector. See “Using the remote control cursor” for details.
Many notebooks have not activated their monitor jack after being connected to the monitor. The
user can often press FN + F3 or CRT/LCD button to switch ON/OFF the externally connected
monitor. Find the function key labeled with the CRT/LCD or monitor icon on the notebook. Press
the FN key and the labeled function key. Please refer to the instruction manual provided with the
notebook computer for the combination keys and their functions.
Connect to the monitor
If you want the display to be shown both on the computer monitor as well as the
screen, refer to the following instructions. Connect the VGA cable to the MONITOR
OUT signal output jack on the projector as well as the external display.
1. Connect the projector to the computer as described in the [Connect to Com-
puter] section.
2. Use a suitable VGA cable (only 1 such cable is provided) and connect one end
of the cable to the D-Sub input jack on the video display.
If the display is provided with a DVI input jack, then connect the DVI end of the
VGA-DVI-A cable to the DVI input jack on the video display.
3. Connect the other end of the cable to the COMPUTER OUT jack on the
projector.
COMPUTER OUT output will only be generated when the cable is connected to the COMPUTER
IN jack of the projector.
This connection mode can only be used when the projector is in Standby Mode. Go to Signal
Source > Standby and activate the VGA Out function in the setup menu.
16
Connecting to Video source devices
You can connect the projector to any of the following video source device with an output jack:
• HDMI
• Component video
• S- video
• Video (composite video)
Only 1 of the aforementioned connection methods is required to connect the projector to
the video source device. However, different connection methods would provide a different
video quality. The connection method selected would be determined by the presence of
matching jacks on the projector and Video source device:
Bestvideoquality
HDMI is the best video connection method available. If the source device comes with
HDMI jacks, you will be able to acquire uncompressed digital video quality.
Please refer to “Connecting to HDMI devices” for details on how to connect the projector to
HDMI devices.
If you don’t have any usable HDMI source, the next best video signal would be Component
Video (not to be confused with Composite Video). Digital TV tuners and DVD players are
provided with Component Video output sockets. If your device includes Component Video,
then this would be your primary choice of connection to the (composite) video.
Please refer to “To connect the projector to a Component Video source device:” for details
on how to connect your projector to Component Video devices.
Bettervideoquality
S-video method provides slightly better simulation video compared to standard composite
videos. If the video device is provided with both composite video and s-video output jacks,
you should try to choose S-video connection rst.
Please refer to “To connect the projector to a S-Video source device:” for details on how to
connect your projector to S-video devices.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
Please refer to “Connecting to composite video source devices” for details on how to
connect your projector to composite video devices.
Connecting audio
The projector includes built-in dual-channel speakers that is designed to provide basic
audio functionality accompanying data presentations for business purposes. It is not
designed for, nor intended for stereo audio reproduction use as might be expected in home
theater or home cinema applications.
17
Connecting to HDMI devices
Use an HDMI cable to establish a connection between the projector and HDMI device.
1. Connect one end of the HDMI cable to the HDMI output jack on the video device.
2. Connect the other end of the cable to the HDMI signal input jack on the projector.
In the unlikely event that the projector is connected to a DVD player via the projector’s HDMI
inputandtheprojectedpicturedisplayswrongcolors,pleasechangethecolorspacetoYUV.
See “Changing HDMI input settings” for details.
To connect the projector to a Component Video source
device:
Examine your Video source device to determine if a set of unused Component Video
output sockets is available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method to use to connect to the device.
1. Take a VGA (D-Sub) Component adapter cable and connect the end with 3 RCA
type connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to blue,
and red to red.
2. Connect the end of the VGA (D-Sub) Component adapter cable (with the D-Sub type
connector) to the COMPUTER IN1/IN2 jack on the projector.
If the selected video image is not displayed after the projector is turned on and the correct
videosourcehasbeenselected,checkthattheVideosourcedeviceisturnedonandoperating
correctly. You must also check that the signal cables have been connected correctly.
To connect the projector to a S-Video source device:
Examine your Video source device to determine if an unused S-Video output socket is
available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method to use to connect to the device.
1. Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
If the selected video image is not displayed after the projector is turned on and the correct
videosourcehasbeenselected,checkthattheVideosourcedeviceisturnedonandoperating
correctly. You must also check that the signal cables have been connected correctly.
If you have already made a Component Video connection between the projector and this
S-VideosourcedeviceusingComponentVideoconnections,anS-Videoconnectionwillnotbe
required as this is an unnecessary second connection of poorer picture quality. See
“Connecting to Video source devices” for details.
18
Connecting to composite video source devices
Examine your Video source device to determine if an unused composite output jack is
available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method to use to connect to the device.
1. Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2. Connect the other end of the video cable to the VIDEO socket on the projector.
If the selected video image is not displayed after the projector is turned on and the correct
videosourcehasbeenselected,checkthattheVideosourcedeviceisturnedonandoperating
correctly. You must also check that the signal cables have been connected correctly.
You need only connect to this device using a composite Video connection if Component Video
and S-Video inputs are unavailable for use. See “Connecting to Video source devices” for
details.
Audio playback with the projector
During demonstration, you may use the projector (mixed dual channel) speakers or
connect separate sound systems with sound amplication functions to the AUDIO OUT
sockets on the projector.
If you have a separate sound system, you should connect the audio output of your Video
source device to this sound system instead of the mono audio input on the projector.
19
Operation
Activate the projector
Plug the power cord into the projector and into a wall socket. Turn on the switch on the
wall socket (if available).
Press Power to switch on the projector.
If this is the rst time that you've switched on the projector, please refer to on-screen
instructions and select your OSD language.
Switch on all connected equipment.
The projector will then begin a search of the input signals. The lower right corner of the
screen will display the current input signal being scanned. If the projector fails to detect a
valid signal, the screen will display a [NO SIGNAL] message until an input signal is found.
You can press Source to select the input signal required. See “Switching input signal” for
details.
Iftheinputsignalfrequency/resolutionexceedstheworkingrangeoftheprojector,theblank
screen will display the [Out of Range] message. Please change to an input signal which is
compatible with the projector's resolution or set the input signal to a lower setting. For more
details,pleaserefertothe[ResolutionTable].
Using the menus
This projector is provided with an On-Screen Display (OSD) menu function, allowing
you to make changes to various settings.
The following OSD screenshot is for reference only. Actual OSD design may differ.
The following is an overview of the OSD menu.
Main menu icon
Status
Press BACK to
go back to the
previous
window or to
exit.
Select
Sub-menu
20
1. Press and select Display, then
press / to select screen color.
2. Press and select Image, then press
/ select the primary color mode.
3. Press and select Power
Management, then press / to
select automatic activation of power.
4. Press and select Basic, then press
/ to start audio channel setup.
5. Press and select Advanced, then
press / to select 3D settings.
6. Press and select System, then
press / to select the primary
language.
21
Disabling the password function
For security purposes and to help prevent unauthorized use, the projector includes an
option for setting up password security. Passwords may be set using the On-Screen
Display (OSD) menu. Please refer to the [Menu Use] section for details on OSD menu
operations.
It is troublesome if you keep forgetting the password after setting up password protection. We
recommend writing down the password and placing it somewhere safe for future reference in
case you forget.
Setting a password
Onceapasswordhasbeenset,theusermustprovidethecorrectpasswordafterstartingthe
projector.Otherwise,theprojectorcannotbeused.
1. Open the OSD Menu and enter System setup >
SYSTEM > Security Settings > Security Settings
menu.
2. Press [Enter]. The Security Settings page will be
displayed.
3. Select Power Lock, then press / and select ON.
4. The picture on the right shows 4 arrow keys (, ,
, ) which each represent 4 numbers (1, 2, 3, 4)
respectively. According to the password you desire
to set, press the arrow keys to enter six digits for the
password.
5. Enter the password and conrm that password.
After completing password settings, the OSD menu will return to the Security
Settings page.
6. Press [Exit] to leave the OSD menu.
If you forget your password
If the password function is activated, you will be
asked to enter the six-digit password every time
you turn on the projector. If you enter the wrong
password, the password error message as pictured
to the right will be displayed for 5 seconds before
the message [INPUT PASSWORD] is shown. You
can enter another 6-digit password. You may use
the password recall procedure if you forgot your
password and did not record it in this manual. See
“Entering the password recall procedure” for details.
If you enter an incorrect password 5 times in succession, the projector will
automatically shut down in a short time.
22
Entering the password recall procedure
1. Press and hold the [Auto Sync] button on the remote control for 3 seconds. The
projector will display a coded number on the screen.
2. Write down the number and turn off your projector.
3. Seek help from the local service center to decode the number. You may be required
to provide proof of purchase to verify that you are an authorized user of the projector.
The [XXX] number in the screenshot shown above is determined by the projector model number.
Change Password
1. Open the OSD and enter System Settings > Security Settings > Change
Password menu.
2. Press [Enter]. The message [INPUT CURRENT PASSWORD] will be shown.
3. Enter the old password.
• If the password entered is correct, another message [INPUT NEW PASSWORD]
will be shown.
• If the password entered is incorrect, then the password error message will
be displayed for 5 seconds before the screen shows the [INPUT CURRENT
PASSWORD]. You will then need to re-enter the password. You can either press
[Exit] to cancel the process or try other passwords.
4. Enter a new password.
5. Enter the password and conrm that password.
6. You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7. Press [Exit] to leave the OSD menu.
Any digit entered will be displayed as asterisks [*] on-screen. We recommend writing down the
password and placing it somewhere safe for future reference in case you forget.
Disabling the password function
1. Open the OSD menu and enter System Settings > Security Settings > Power
Lock Menu.
2. Press / and select OFF.
3. The [INPUT PASSWORD] message will be shown. Enter the current password.
• If the password is correct, the OSD menu will return to the Security Settings
page and show Power Lock in the [OFF] column. You will not have to enter the
password next time you turn on the projector.
• If the password entered is incorrect, then the password error message will be
displayed for 5 seconds before the screen shows the [INPUT PASSWORD]. You
will then need to re-enter the password. You can either press [Exit] to cancel the
process or try other passwords.
Thoughthepasswordfunctionisdisabled,youneedtokeeptheoldpasswordinhandshould
you ever need to re-activate the password function by entering the old password.
23
Switching input signal
The projector can be connected to multiple
devices at the same time. However, it can only
display one full screen at a time.
If you want the projector to automatically search
for various signals, please conrm that the
SYSTEM > Quick Auto Search function in the
Source menu is switched ON.
You may also press the source selection button
on the remote control or search for available input
signals to manually select the desired signals.
1. Press [Source] to display the source selection col-
umn.
2. Keep pressing the / until you arrive at the
desired signal, then press [Enter].
Once detected, the selected source information
will display on the screen for seconds. If there
are multiple devices connected to the projector,
repeat steps 1 to 2 to search for another signal.
Fordisplayresolutionsofthisprojector,pleasereferto“Projectorspecications”.
Toachievethebestimagedisplayeffects,youshouldselectanduseaninputsignalthat
outputs at this resolution. Any other resolutions will be scaled by the projector depending upon
theaspectratiosetting,whichmaycausesomeimagedistortionorlossofpictureclarity.See
“Selecting the aspect ratio” for details.
24
Changing HDMI input settings
In the unlikely event that you connect the projector to a device (such as DVD or Blu-
ray player) via the projector’s HDMI input jack, and the projected picture displays the
wrong colors, please change the color space settings to one that complies with the
color space settings of the output device.
To perform this operation:
1. Open the OSD menu and enter ADVANCED > HDMI settings Menu.
2. Press [Enter].
3. Select HDMI format, then press / to select a suitable color space according to
the color space settings of the output device.
• RGB: Changes the color space to RGB.
• YUV: Changes the color space to YUV.
• Auto: Sets the projector to automatically detect the color space settings of the
color space.
4. Select HDMI Range, then press / to select a suitable color range according to the
color range settings of the output device.
• Enhanced: Changes HDMI color range to 0-255
• Normal: Changes HDMI color range to 16-235.
• Auto: Sets the projector to automatically detect the HDMI range of the input signal.
This function is only available when the HDMI input jack is being used.
Please refer to equipment documentation to gain more details on color space and HDMI range
settings.
25
Adjusting the projected image
Adjusting the projection angle
The projector is furnished with an adjustment
support peg. The adjustment support peg may
be used to adjust projection height and projection
angle along the vertical axis. The user may
turn the adjustment support peg to make ne
adjustments to projection angle and position of
the projected image until it reaches the desired
location.
If the projector is placed on an uneven surface or where the screen and projector
are not perpendicular to each other, the projected image may be subject to keystone
(trapezoidal) distortion. For more details on projection calibration, please refer to
“Correcting keystone”.
Auto-adjustments to the image
You may need to optimize picture quality in some cases. To do this, press and hold
the [Auto Sync] button of the remote control. Within 5 seconds, the built-in Intelligent
Auto Adjust function will re-adjust the values of Frequency and Clock to provide the
best picture quality.
The current source information will be displayed in the upper left corner of the screen
for 3 seconds.
WhenusingAutoAdjustfunction,theentirescreenwillturnblack.
ThisfunctionisonlyavailablewhenPCD-Subinputsignal(analogRGB)isselected.
Auto-adjustments to image clarity
The focusing ring can be turned to adjust image clarity.
26
Correcting keystone
Keystone distortion is a problem where the projected image becomes trapezoidal in shape
(keystone distortion) as a result of poor projection angle.
To correct this situation, you should adjust projector height and use the following steps to
correct the issue manually.
• Using the remote control
1. Press / / / to display the Keystone Correction page.
2. Press to initiate Keystone Correction at the
top of the image. Press to initiate Keystone
Correction at the bottom of the image. Press
to initiate Keystone Correction at the right
side of the image. Press to initiate Keystone
Correction at the left side of the image.
Press Press
• Using the OSD menu
1. Open the OSD menu and open Display >
Keystone menu.
Press Press
2. Press the button to initiate Keystone Correction at the top of the image or press
the button to initiate Keystone Correction at the bottom of the image.
3. Open the OSD menu and open Display > Keystone menu.
4. Press [Enter]. This will bring up the Keystone page.
5. Select Vertical and then press to initiate Keystone Correction at the top of the
image or press to initiate Keystone Correction at the bottom of the image.
6. You can also select Horizontal and then press to initiate Keystone Correction at
the right side of the image. Press to initiate Keystone Correction at the left side of
the image.
27
Adjusting the 4 corners
You may manually adjust the irregular shapes and
sizes of the rectangular image manually.
1. To display the Corner Adjustment page, please
follow any one of these steps:
i. Press [Enter].
ii. Open the OSD Menu and enter Display >
Corner Adjustment menu and press [Enter].
This will bring up the Corner Adjustment
page.
2. Press /// to select the corner you wish to
adjust, and then press [Enter].
3. Press / to select a suitable adjustment
method and then press [Enter].
4. As shown in the screen, (/ to perform 45
degree adjustments and /// to perform
90 degree adjustments). Please press ///
to adjust the shapes and size. You can press
[Menu] or [Exit] to return to the previous step.
Press and hold [Enter] for 2 seconds to reset the
settings of the selected corner.
Adjusting Keystone Correction will reset Corner
Adjustment settings.
Todisplaythispage,press
and hold [Enter] for 2
seconds to reset the
settings for all 4 corners.
Shows the corner that
you have selected.
AftermakingCornerAdjustmentsettings,youwillnolongerbeabletoadjustcertainaspect
ratios or time sequences.
Incaseyouneedtoperformthesechanges,pleaseresetthesettingsforall4corners.
The following message will be displayed:
28
Zoomoutfordetailedreview
You may need to expand the image to inspect details in the projected image. Use the
arrow keys to move the images.
• Using the remote control
1. Press the on the remote to bring up the Zoom Bar.
2. Press repeatedly to expand the image to the desired dimension.
3. To browse the image, press [Enter] to switch to displacement mode and use the
arrow keys (, , , ) to move the image for browsing.
4. To shrink the image, press [Enter] again to return to the Zoom In/Out function and
press repeatedly to restore the image to its original size. You can also press the
[Auto Sync] button on the remote control to restore the image to its original size.
• Using the OSD menu
1. Open the OSD menu to enter Display > Zoom menu.
2. Press [Enter]. This will bring up the Zoom Slider.
3. Repeat Steps 2-4 listed above in the Remote Control Use chapter.
The image can only be inspected after zooming out. You can zoom out further to inspect details.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV
and computers have a 4:3 aspect ratio, while digital TV and DVDs have 16:9 aspect
ratios.
With the advent of digital signal processing, digital display devices like this projector
can dynamically stretch and scale the image output to a different aspect than that of
the image input signal.
To change the projected image ratio (no matter what aspect the source is):
1. Open the OSD Menu and enter Display > Aspect ratio menu.
2. Press / to select an aspect ratio that suits the format of the video signal and your
display requirements.
29
About the aspect ratio
Inthepicturebelow,theblackportionsareinactiveareasandthewhiteportionsareactive
areas. OSD menus can be displayed on those unused black areas.
1. Auto: Proportional scaling of an image to t the
projector’s natural resolution in its horizontal
width. This is suitable where the incoming image
is neither in 4:3 nor 16:9 aspect ratios but where
you want to make most use of the screen without
altering the image’s aspect ratio.
Image 16:10
Image 16:9
2. 4:3: Scales a picture so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 pictures such as those for
computer monitors, standard denition TV, and
4:3 aspect DVD movies as these can be displayed
without aspect alteration.
Image 4:3
3. 16:9: Scales a picture so that it is displayed
in the center of the screen with a 16:9 aspect
ratio. This is most suitable for images which are
already in a 16:9 aspect such as high denition
TV because as these can be displayed without
aspect alteration.
Image 16:9
4. 2.35:1: Scales a picture so that it is displayed at
the center of the screen with a 2.35:1 aspect ratio
without change.
Image 2.35:1
30
Optimizing the image
Selecting a picture mode
The projector is preset with several predened picture modes. You may choose one of
these modes that best ts your operating environment and input signal picture type.
To select an operation mode that suits your need, please follow the steps described
below.
• Press [Color Mode] repeatedly until you arrive at the mode you desire.
• Enter IMAGE > Color mode menu and press / to select the required mode.
Picture modes for different types of signals
The following lists the Picture modes that can be used for different signal types.
1. Brightest: Maximizes the brightness of the projected image. This mode is suitable
when using projectors in environments such as well-lit rooms where extra-high
brightness is required.
2. Dynamic mode: Used during daytime demonstration to match PC and notebook
computer color tones. The projector will also refer to the projected contents and use
dynamic PC functions to optimize image quality.
3. Standard mode: Used during daytime demonstration to match PC and notebook
computer color tones.
4. ViewMatchsRGBmode: Switches between high brightness levels or precise color
functions.
5. Movie Mode: Applicable for playing colored movies, video clips from digital cameras,
or DVs from a PC input in darker (dim) environments to achieve the best viewing
effects.
The available light source modes will be based upon the selected color mode.
Using Screen Color
When the projection surface is colored (such as walls that are painted in colors other than
white), the Screen Color function can be used to calibrate the color of the projected image
in order to prevent color offsets between the source and color of the projected image.
To use this function, go to Display > Screen Color menu, and press / to select
the color that is closest to that of the projection surface. Several preset color options
are available, namely: white board, green board and blackboard. These setup
functions may differ according to model type.
This function is only available when PC or HDMI input signals were selected.
31
Fine-tuning of image quality in user modes
You may use several user-dened functions if the projector detects certain signal
types. You can make adjustments to these functions based on your needs.
AdjustingBrightness
Enter IMAGE > Brightnessmenu and then press
/.
The higher the value, the brighter the image. And
lower the setting, darker the image.
Adjusting this control allows the black area of the image to appear just as black to
reveal details within.
Adjusting Contrast
Enter IMAGE > Contrast menu and then press
/.
The higher the value, the greater the contrast. After
adjusting Contrast, this function may be used to set
the peak-white level that matches the input signal
and observed environment of your choice.
Adjusting Color
Enter IMAGE > Advanced > Color menu and press /.
Lower settings produce less color saturation. If the setting is too high, colors on the
image will be overpowering, which makes the image unrealistic.
ThisfunctionisonlyavailablewhentheinputsignalsareS-Video,Video,YPbPr(digital)or
YCbCr(digital).
Adjusting Tint
Enter IMAGE > Advanced > Tint menu and then press /.
The higher the value, the more reddish the picture becomes. The lower the value, the
more greenish the picture becomes.
ThisfunctionisonlyavailablewhentheinputsignalsareS-Video,Video,YPbPr(digital)or
YCbCr(digital).
Adjusting Sharpness
Enter IMAGE > Advanced > Sharpness menu and then press /.
Higher settings produce sharper images. The lower the value, the softer the picture
becomes.
ThisfunctionisonlyavailablewhentheinputsignalsareS-Video,Video,YPbPr(digital)or
YCbCr(digital).
32
AdjustingBrilliantColor
Enter IMAGE > Advanced >BrilliantColormenu, and then press /.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors of the projected image.
Brightness levels of mid-tone areas commonly seen in videos and natural landscapes
are increased by more than 50%, allowing the projector to generate images in realistic
and true colors. To acquire this quality of images, please select the level you desire. If not
required, set this option to OFF.
Reducing image noise
Enter IMAGE > Advanced > Noise Reduction menu, and then press /.
This function is capable of reducing image noise generated electrically by different media
players. Higher settings will provide lower image noise.
ThisfunctionisonlyavailablewhenPC,Video,orS-Videoinputsignalswereselected.
Selecting a gamma setting
Enter IMAGE > Advanced > Gamma menu, and then press / to choose the desired
settings.
Gamma refers to the relationship between input source and image brightness.
Selecting a Color Temperature
Enter IMAGE > Color Temperature menu, and then press /.
Options available to Color Temperature settings will depend on the choice of the signal type.
1. Cool: Provides the highest color temperature. Cool colors allow the image to display
white colors with the more blue undertones compared to other temperatures.
2. Neutral: White colors in the image will be provided with a light blue undertone.
3. Normal: Maintains a normal white color tone.
4. Warm: White colors in the image will be provided with a light red undertone.
Setting a preferred color temperature
1. Enter IMAGE > Color Temperature menu.
2. Press / to select Cool, Neutral, Normal or Warm, and press [Enter].
3. Press / to select the item you wish to change, then press / to adjust its value.
• RedGain/GreenGain/BlueGain: Adjusts the contrasts of the red, green, and
blue colors.
• RedOffset/GreenOffset/BlueOffset: Adjusts the brightness of red, green, and
blue colors.
33
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides ne color control adjusent to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc that contains various color test patterns that can be used
to test the color presentation of monitors, TVs, and projectors, any image from the disc can
be projected on screen and adjusted using the Color Management menu.
To adjust the settings:
1. Open the OSD menu, go to IMAGE > Advanced >
Color Management menu.
2. Press [Enter] to bring up the Color Management
page.
3. Select Primary Color, then press / and select
any one of the colors from red, yellow, green, cyan,
blue, or magenta.
Red
Blue
Green
CyanMagenta
Yellow
4. Press to select the Tint, then press / to select the range. Enlarging the range
will include colors composed of higher proportions of 2 similar colors.
Please refer to the illustration to the right for how the colors relate to each other.
For example, if you select red and set the range to 0, you will only select pure red
areas of the projected image. Increasing the range will include shades of red closer
to yellow and magenta.
5. Press and select Saturation, then press / to adjust its values according to
your preferences. The effect of each adjustment will be immediately reected upon
the image.
For example, if you select Red and set its value at 0, only the saturation of pure red
will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less saturated
colors.Asettingof0willremovethatcolorfromtheimageentirely.Ifthesaturationistoohigh,
that color will be overpowering and unrealistic.
6. Press and select Gain, then press / to adjust its values according to your
preferences. This affects the contrast level of the primary color selected. The effect of
each adjustment will be immediately reected upon the image.
7. Repeat steps 3 to 6 to carry out other color adjustments.
8. Make sure you have made all of the desired adjustments.
9. Press [Exit] to save the settings and exit.
34
Setting the Presentation Timer
The presentation timer can indicate the presentation time on-screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1. Use the remote control and enter Presentation Timer menu or enter Basic>
Presentation Timer menu.
2. Press [Enter] to show the Presentation Timer page.
3. Select Timer Period and press / to conrm the duration. Duration can be set to 1
to 5 minutes, with 1 minute increments, or 5 to 240 minutes in 5 minute increments.
Oncethetimerhasbeenactivated,resettingthetimerintervalwillre-activatethetimer.
4. Press and select the Timer Display. Then press / to select whether to display
or hide the on-screen timer.
Selection Description
Always Displays the timer on screen throughout the presentation time.
1 min/2 min/3 min Display timer on-screen in the last 1 / 2 / 3 minutes.
Never Hides the timer throughout the presentation time.
5. Press and select Timer Position, and then press / to set timer location.
Top- Left BottomLeft Top Right BottomRight
6. Press to select Timer Counting Direction, then press / to select the required
timer method.
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decrease from the preset time to 0.
7. To activate Presentation Timer, press , then press / and select Start Counting,
then press [Enter].
8. A conrmation message will be displayed next. Select Yes and press [Enter] to
conrm the selection. The screen will display the message [Timer is On!]. Once
activated, the timer will start its countdown.
Tocancelthetimer,performthefollowingsteps:
1. Enter Basic>PresentationTimer menu.
2. Select OFF. Press [Enter]. A conrmation message will be displayed afterwards.
3. Select Yes and press [Enter] to conrm the selection. The screen will display the
message [Timer is Off!].
35
Hiding the image
In order to draw the audience’s attention to the presenter, you may press Blank
to hide the screen image. Press any key on the projector or remote to restore the
image. After hiding the image, the lower right corner of the screen will display the text
[BLANK].
You can go to Basic > BlankTimer menu to set blank screen duration. Once the
blank screen countdown is complete, the image will be automatically re-displayed.
Afterpressing[Blank],theprojectorwillautomaticallyenterPowerSavingmode.
Caution
Do not block the projector lens. The blocking item may be heated to the point of deformation or
mayevencauseare.
Locking control keys
Locking the control buttons of the projector allows you to prevent projector settings
from being changed accidentally (by children, for example). Once Panel Key Lock
has been activated, with the exception of the Power button, none of the buttons on
the Projector could be used.
1. Press (PanelKeyLock) or enter System Settings > Panel Key Lock menu.
2. Press / and select ON.
3. A conrmation message will be displayed next. Select Yes to conrm your choice.
To switch off the Panel Key Lock, press and hold the button on the Projector for 3
seconds.
You may also use the remote to enter System Settings > Panel Key Lock menu,
press / and select OFF.
ButtonsontheremotecontrolcanstillbeusedevenifthePanelKeyLockfunctionhasbeen
switched on.
If you press the Power button to switch off the projector without switching off the Panel Key
Lockfunction,theprojectorbuttonswillremainlockedwhenyouswitchitonthenexttime.
36
Creating your own startup screen
In addition to Black, Blue, or ViewSonic screens, you may also select a computer or
video projection image as your startup screen.
To create your own startup screen:
1. Select the desired startup screen image from your computer or video source.
2. Open the OSD menu and enter Basic > Screen Capture menu.
3. Press [Enter].
4. A conrmation message will be displayed next. Press [Enter] again.
5. While the projector processes the image, the screen will display the message
[Screen Capture in Progress...]. Please wait.
6. When successful, the screen will display the message [Screen Capture Success].
The captured image will be saved as a Screen Capture and set as your current
startup screen.
In the unlikely event that the capturing action fails, change your target picture. When
it happens, please set the resolution of the input signal under native resolution and
try again.
Operations at high altitudes
We recommend using the High Altitude Mode when the environment is at 1500 to
3000 meters above sea level and the temperature is between 5°C to 25°C.
Caution
Do not activate High Altitude Mode if the environment is at 0 to 1500 meters above sea level and
the temperature is between 5°C to 35°C.
Activating High Altitude Mode under such circumstances will lead to excessive cooling of the
projector.
Activating High Altitude Mode:
1. Open the OSD menu and enter System Settings >
High Altitude Mode menu.
2. Press and select ON. / will display a
conrmation message.
3. Select Yes, and then press [Enter].
There is a chance that louder operational noises
will be generated when using the projector in High
Altitude Mode. The reason for this is the increased
fan speed necessary to improve overall system
cooling and performance.
Using this projector under extreme environments that exceed the aforementioned
limits may lead to auto-shutdown designed to prevent overheating of the projector.
Under such circumstances, you should switch to High Altitude Mode to solve these
issues. However, this does not mean that this projector is able to operate under any
and all harsh or extreme conditions.
37
Using the CEC function
This projector supports Consumer Electronics Control (CEC), allowing you to connect
to connect to HDMI and achieve synchronized power ON/OFF operations. This
means that when a device that also supports CEC is connected to the HDMI input
jack of the projector, switching off the power of the projector will also automatically
switch off the power of the connected device. Switching on the power of the
connected device will also automatically switch on the projector.
Activating the CEC function:
1. Open the OSD menu and enter Power management > Auto Power On > CEC
menu.
2. Press / and select Enable.
ToensureproperoperationsoftheCECfunction,pleaseverifythatthetargetdevicehasbeen
connected to the HDMI input jack via an HDMI cable and that the CEC function has been
activated.
CEC function may not be usable according to the connected equipment.
3D functions
This projector also comes with 3D functions that offer greater depth and immersion
when viewing 3D movies, videos, sports, and games. You would need a pair of 3D
glasses when viewing 3D images and videos.
If the 3D signal comes from an HDMI 1.4a compatible device, this projector will look
for a 3D Sync data signal. Once detected, the projector will automatically switch to 3D
projection. Under other circumstances, you may need to manually select the 3D Sync
format to ensure that the proper projection of 3D images.
Selecting 3D Sync formats:
1. Use the 3D button on the remote control to enter the 3D Settings menu or enter
Advanced > 3D Settings menu.
2. Press [Enter] to bring up the 3D Settings page.
3. Highlight 3D Glasses and press / to select DLP or 3D VESA.
Once 3D Sync function has been activated:
•Brightnessoftheprojectedimagewillbereduced.
•Colormodescannotbeadjusted.
•Zoomfunctionscanonlyenlargetheimagetoalimiteddegree.
Ifthe3Dimagehasbeenseverelyinverted,youmaysetthe3DSyncInvertfunctionto[Invert]
to correct this problem.
Using the projector under standby mode
A number of projector functions can be used under Standby Mode (plugged in to
power but not switched on). To use these functions, please check that you have
switched on the Power management > Standby Settings and its secondary menu
items, and that the cables have been properly connected. Refer to the chapter on
cable connections for more information on cable connections.
38
Active VGA Out
Once the COMPUTER IN and COMPUTER OUT jacks have been properly connected
to the corresponding devices, select ON to generate VGA signal output. The projector
will only receive output signals via Computer In 1.
Active Audio Out
When the AUDIO IN jack is correctly connected to a device, select ON to output audio
signals.
Adjusting the sound
The sound adjusents made as below will have an effect on the projector speaker(s).
Please check that you have made a correct connection to the projector audio input /
output jacks. See “Connection” for details.
Adjustments in Audio Mode
1. Open the OSD menu and enter Basic > Audio Settings > Audio Mode menu.
2. Press / to select the primary Audio Mode.
Ifavailable,youmaypressthe[AudioMode]ontheremotecontroltoselecttheprimaryAudiomode.
Mute
1. Open the OSD menu and enter Basic > Audio Settings > Mute menu.
2. Press / and select ON.
Ifavailable,youmaypressthe button on the remote control to switch the projector audio
ON or OFF.
Adjusting the sound level
1. Open the OSD menu and enter Basic > Audio Settings > Volume menu.
2. Press / to select the desired volume.
Ifavailable,youmaypressthe button on the remote control to adjust speaker volume of
the projector.
Switch off the projector
1. Press the Power button. A conrmation message will be displayed on screen. The
message will disappear if you do not respond within a few seconds.
2. Press the Power button again.
3. Disconnect the power cord from the wall socket if the projector will not be used in an
extended period of time.
39
Menu operations
Menu system
Please note that the on-screen display (OSD) menu may vary according to the type of
signal received.
The projector must detect at least one valid signal in order to use the menu items. If no
device has been connected to the projector or if no signal has been detected, only a few
menu items will be accessible.
Main menu Sub-menu Options
1.
Display
Screen Color Off/Blackboard/Greenboard/
Whiteboard
Aspect Ratio Auto/4:3/16:9/16:10/2.35:1
Keystone Auto V Keystone Off/On
Manual Vertical/Horizontal
Corner Adj.
Position
Phase
H. Size
Zoom
OverScan Off/1/2/3/4/5
2.
IMAGE
Color mode Brightest/Dynamic/Standard/ViewMatchsRGB/
Movie
Brightness
Contrast
Color Temperature
Warm RedGain/GreenGain/Blue
Gain/Red Offset/Green
Offset/BlueOffset
Normal
Neutral
Cool
Color
Advanced
Tint
Sharpness
Gamma 1/2/3/4/5/6/7/8
BrilliantColor Off/1/2/3/4/5/6/7/8/9/10/13
Noise Reduction
Color Management
Primary color
Tint
Saturation
Gain
Reset color settings Restore/Cancel
40
Main menu Sub-menu Options
3.
Power
Management
Auto Power On
Computer Disable/Enable
CEC Disable/Enable
Direct power on Off/On
Smart Energy
Auto Power Off Disable/10 min/20 min/
30 min
Sleep Timer Disable/30 min/1 hr/2 hr/
3 hr/4 hr/8 hr/12 hr
Power saving Disable/Enable
MHL settings Power Out MHL/USB-TYPEA
MHL reset Reset/Cancel
Standby Settings Active VGA Out Off/On
Active Audio Out Off/On
4.
Basic
Audio Settings
Audio Mode Standard/Speech/
Entertainment
Mute On/Off
Volume
Presentation Timer
Timer Period 1~240 m
Timer Display Always/1 min/2 min/3 min
Timer Position Top-Left/Bottom-Left/Top-
Right//Bottom-Right
Timer Counting
Direction Count Down/Count Up
Start Counting/Off
Pattern Off / 1/ 2/ 3
BlankTimer Disable/5 min/10 min/15
min/20 min/25 min/30 min
Message On/Off
Splash Screen Black/Blue/ViewSonic/
Screen Capture/Off
Screen Capture
MyButton
Auto/Projection(ProjectorPosition)/Menu
Position/ColorTemp./Brightness/Contrast/3D
Settings/Screen Color/Splash Screen/Message/
Quick Auto Search/CEC/DCR/Closed Caption/
Power Saving/Freeze/INFORMATION/Aspect
Ratio/Power Out
41
Main menu Sub-menu Options
5.
Advanced
3D Settings
3D Glasses DLP/3D VESA
3D Sync
Auto/Off/Frame Sequential/
FramePacking/Top-Bottom/
Side-by-Side
3D Sync Invert Disable/Invert
HDMI Settings HDMI Format Auto/RGB/YUV
HDMI Range Auto/Enhanced/Normal
LAN Control
Settings
LAN Control
Settings DHCP ON/Static IP
Projector IP
Address
Subnet Mask
Default Gateway
DNS Server
Standby LAN
Control Off/On
Apply
Light Source
Settings
Light Source Mode Normal/Eco
Light Source Hours
DCR On/Off
Closed Caption Caption Version Off/ CC1/ CC2/ CC3/ CC4
Reset Settings Reset/Cancel
5.
System
Language Multi-language OSD
selection
Projector Position Front Table/Rear Table/Rear
Ceiling/Front Ceiling
Menu Settings
Menu Display Time 5 sec/10 sec/15 sec/20
sec/25 sec/30 sec
Menu Position Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
High Altitude Mode On/Off
Quick Auto Search On/Off
Security Settings Change Password
Power On Lock On/Off
Panel Key Lock On/Off
Remote Control
Code 1/2/3/4/5/6/7/8
6.
Information
•Source
•ColorMode
•Resolution
•ColorSystem
•IPAddress
•MACAddress
•FirmwareVersion
42
Description of each menu
FUNCTION Description
1. Display menu
Screen Color See “Using Screen Color” for details.
Aspect Ratio See “Selecting the aspect ratio” for details.
Keystone See “Correcting keystone” for details.
Corner Adj. See “Adjusting the 4 corners” for details.
Position
Displays the position adjustment page. To move the
projected image, use the directional arrow keys. The
values shown on the lower position of the page change
with every key press you made until they reach their
maximum or minimum.
This function is only available when a PC input signal is
selected.
The adjustment range may vary under different timings.
Phase
Adjusts the clock phase to reduce image distortion.
This function is only available when a PC input signal is
selected.
H. Size
Adjusts the horizontal width of the image.
This function is only available when a PC input signal is
selected.
Zoom See “Magnifying and searching for details” for details.
OverScan
Adjusts the overscan rate from 0% to 5%.
ThisfunctionisonlyavailablewhenaCompositeVideo,
S-Video or HDMI input signal is selected.
2. Image menu
Color mode See “Selecting a picture mode” for details.
Brightness See “Adjusting Brightness” for details.
Contrast See “Adjusting Contrast” for details.
Color Temperature
For more details, please refer to “Selecting a
Color Temperature” and “Setting a preferred color
temperature”.
43
FUNCTION Description
2. Image menu
Advanced
Color
See “Adjusting Color” for details.
Tint
See “Adjusting Tint” for details.
Sharpness
See “Adjusting Sharpness” for details.
Gamma
See “Selecting a gamma setting” for details.
BrilliantColor
See “Adjusting Brilliant Color” for details.
Noise Reduction
See “Reducing image noise” for details.
Color Management
See “Color Management” for details.
Reset color settings Returns all color settings to the factory preset values.
3. Power Management menu
Auto Power On
Computer
Selecting Enable allows the projector to turn on
automatically once the VGA signal is fed through the
VGA cable.
CEC
See “Using the CEC function” for details.
Direct power on
Selecting On allows the projector to turn on
automatically once the power is fed through the power
cord.
Smart Energy
Auto Power Off
See “Setting Auto Power Off” for details.
Sleep Timer
See “Setting Sleep Timer” for details.
Power Saving
See “Setting Power Saving” for details.
MHL Settings
Please check your MHL dongle and Power Output of
OSD settings before used.
If you’d like to have power charging through additional
USB-type A, make sure to switch the Power Output
from MHL to USB-type A.
MHL Reset
Selecting Reset to reapply power after a power outage.
44
FUNCTION Description
4.BasicMenu
Audio Settings See “Adjusting the sound” for details.
Presentation Timer See “Setting the presentation timer” for details.
Pattern
The projector can display several test patterns. It helps
you adjust the image size and focus and check that the
projected image is free from distortion.
BlankTimer See “Hiding the image” for details.
Message
Selecting On displays the current information on the
screen when the projector is detecting or searching for
a signal.
Splash Screen Allows you to select which logo screen will be displayed
during projector start-up.
Screen Capture See “Creating your own startup screen” for details.
My buttons Sets a hotkey on remote control.
5. Advanced menu
3D Settings See “Using the 3D functions” for details.
HDMI Settings See “Changing HDMI input settings” for details.
Audio Settings See “Adjusting the sound” for details.
LAN Control Settings See “Controlling the projector through a LAN
environment” for details.
Light Source Settings
Light Source Mode
See “Setting Light Source Mode” for details.
Light Source Hours
See “Getting to know the Light Source hour” for details
on how the total Light Source hour is calculated.
DCR
Enables or disables the DCR (Dynamic Contrast Ratio)
function. Selecting On enables the function and the
projector will automatically switch the Light Source
mode between normal and economic modes according
to the input image detected.
This function is only available when a PC input signal is
selected.
AfterenablingDCR,frequentLightSourcemode
switching may shorten Light Source life and noise level
will vary during operation.
45
FUNCTION Description
5. Advanced menu
Closed Caption
Selects a preferred closed captioning mode when the
selected input signal carries closed captions.
• Captions: An on-screen display of the dialogue,
narration, and sound effects of TV programs and
videos that are closed captioned (usually marked
as “CC” in TV listings).
This function is only available when a Composite video
or S-Video input signal is selected and its system format
is NTSC.
Caption Version
To view captions, select CC1, CC2, CC3, or CC4 (CC1
displays captions in the primary language in your area).
Reset Settings
Returns all settings to the factory preset values.
The following settings will still remain: Keystone /
Corner Adj. / Language/ Projector Position/ High
Altitude/ Security Settings/ Remote Control Code
6. SYSTEM menu
Language Sets the language for the On-Screen Display (OSD)
menus. See “Using the menus” for details.
Projector Position See “Choosing a location” for details.
Menu Settings
Menu Display Time
Sets the length of time the OSD will remain active after
your last key press. The range is from 5 to 30 seconds
in 5-second increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
High Altitude Mode A mode for operation in high altitude areas. See
“Operating in a high altitude environment” for details.
Quick Auto Search See “Switching input signal” for details.
Security Settings See “Utilizing the password function” for details.
Panel Key Lock See “Locking control keys” for details.
Remote Control Code See “Remote control code” for details.
46
FUNCTION Description
6. Information menu
Current System Status
Source
Shows the current signals source.
Color mode
Shows the selected mode in the Image menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows the input system format.
IP Address
Shows the IP address of your projector.
MAC Address
Shows the MAC Address of your projector.
MACAddressstandsforMediaAccessControlAddress,
which is a physical layer address used to uniquely
identify a network node.
Firmware Version
Shows the current rmware version.
47
Maintenance
Care of the projector
You must regularly clean the lens and/or lter.
Do not attempt to disassemble any part of the projector. Contact your dealer if you
need to replace any parts.
Cleaning the lens
You can clean the dust-free glass lens if you notice any dirt or dust on its surface.
• Use a canister of compressed air to remove dust.
• Use a lens cleaning wipe or soft, or a moist cloth with some detergent to clean away
any dust or dirt on the dust-free glass.
Note
Do not apply any granule material on the dust-free glass.
Cleaning the projector case
Before cleaning the case, please refer to the proper shutdown procedure described in
“Switch off the projector” to shutdown the projector and unplug the power cable.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a piece of soft cloth with water and a
neutral pH detergent. Then wipe the case.
Note
Neverusewax,alcohol,benzene,thinners,orotherchemical-baseddetergents.Thesecan
damage the case.
Storing the projector
Follow the instructions below to store the projector for an extended time:
• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to “Specications” or inquire your
dealer for details of the recommended range.
• Retract the projector support pegs.
• Remove the battery from the remote control.
• Pack the projector in its original packaging or equivalent material.
Transporting the projector
It is recommended that you ship the projector within its original packaging or
equivalent material.
48
Usingthelter
Note
• werecommendcleaningthelterswhenusingprojectorforawhile.
• Iftheprojectorissuspendedfromtheceilingormountedinawaythatisdifculttoaccess,pleasebe
mindfulofpersonalsafetyduringlterreplacement.
Cleaningthelters
1. Make sure that the projector has been shut down and unplugged from the power
source.
2. Press the latch pin on the lter and removed the lter from the projector.
3. Use a small vacuum cleaner or soft brush to remove dust from the lter.
4. Reinstall the lter.
49
LED Indicator
Projector status Power indicator Status* indicator
Stand-by Mode Red Off
Powering On
Red ashing two
second , purple
ashing three
second then Blue
ashing 4 second
Off
Normal Operations Blue Off
Normal Shut Down Blue ashing Off
Fan Error Off Red ashing
Temperature Off Red
DMD Blue ashing twice
per second
Red ashing twice
per second
Projector Status:
Color Wheel Error
Power Indicator :
Blue ashing once
per second /
Red ashing twice
per second
LD start failed Blue ashing Red ashing
LD shut down Blue Red ashing
Stand-by Mode
(enable standby
setting on OSD)
blue ashing by ve
second Off
50
Troubleshooting
Projector is not shutting down
Cause Remedy
There is no power from the power cable.
Plug one end of the power cable at the
AC inlet of the projector and the other
end in the power outlet. If the power
outlet has a switch, make sure that it is
switched on.
Attempting to turn the projector on again
during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause Remedy
Video source is not turned on or is not
connected correctly.
Switch the video source on and check
that the signal cable is connected
correctly.
The projector is not correctly connected
to the input signal device. Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal by using
the [Source] key on the projector or
remote control.
Blurredimage
Cause Remedy
The projection lens is not correctly
focused.
Use the focus function to adjust lens
focus.
The projector and the screen are not
aligned properly.
Adjust projection angle and direction as
well as the height of the projector where
necessary.
Remote control does not work
Cause Remedy
The battery is out of power. Replace the batteries.
There is an obstacle between the remote
control and the projector. Remove the obstacle.
You are too far away from the projector. Stand within 8 meters (26 feet) of the
projector.
The remote control does not match the
remote control code of the projector. Adjust the remote control code.
51
Specications
Projectorspecications
• Allspecicationsaresubjecttochangewithoutnotice.
• Not all projector models are available at your location.
L810 L820 L830
Input Terminals
1 VGA Input (DB 15 pin) x2 x2 x2
2 Audio Input (mini jack) x1 x1 x1
3 Audio L/R (RCA x 2 Composite) x1 x1 x1
4 HDMI (v1.4 with audio) x1 x1 x1
5HDMI 1.4/MHL 2.0 x1 x1 x1
6 Video (RCA) x1 x1 x1
7 S-video(Mini DIN 4 pin) x1 x1 x1
8 Component (RCAx3) x1 x1 x1
93Dsync(IR3D) x1 x1 x1
Output Terminals
1 VGA output (DB 15pin) x1 x1 x1
2 Audio Ouput (mini jack) x1 x1 x1
312 V Trigger x1 x1 x1
4USB 5V2A (micro USB cable on
Dongle) x1 x1 x1
5USB A 5V2A x1 x1 x1
6 Speaker 10W x1 10W x1 10W x1
Control Terminals
1 RS232 (9 pin type1) x1 x1 x1
2 USB (Type mini B) 5V2A x1 x1 x1
3 LAN Control(RJ45) x1 x1 x1
52
Dimensions
Ceiling mount installation
Projection direction
Note: M6L12 screws are recommended for securing the projector using suspended
mounting M6 screw holes. (M6 / L12 x 4)
53
Timing chart
AnalogRGB
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
VGA 640x480 4:3 60/72/75/85
SVGA 800x600 4:3 60/72/75/85
XGA 1024x768 4:3 60/70/75/85
1152x864 4:3 75
WXGA 1280x768 15:9 60
1280x800 16:10 60/75/85
1360x768 16:9 60
Quad-VGA 1280x960 4:3 60/85
SXGA 1280x1024 5:4 60
SXGA+ 1400x1050 4:3 60
WXGA+ 1440x900 16:10 60
UXGA 1600x1200 4:3 60
WSXGA+ 1680x1050 16:10 60
HD 1280x720 16:9 60
MAC 13” 640x480 4:3 67
MAC 16” 832x624 4:3 75
MAC 19” 1024x768 4:3 75
MAC 21” 1152x870 4:3 75
HDTV (1080p) 1920x1080 16:9 60
54
HDMI
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
VGA 640x480 4:3 60
SVGA 800x600 4:3 60
XGA 1024x768 4:3 60
WXGA
1280x768 15:9 60
1280x800 16:10 60
1360x768 16:9 60
Quad-VGA 1280x960 4:3 60
SXGA 1280x1024 5:4 60
SXGA+ 1400x1050 4:3 60
WXGA+ 1440x900 16:10 60
WSXGA+ 1680x1050 16:10 60
HDTV(1080p) 1920x1080 16:9 50/60
HDTV (1080i) 1920x1080 16:9 50/60
HDTV (720p) 1280x720 16:9 50/60
SDTV(480p) 720x480 4:3/16:9 60
SDTV(576p) 720x576 4:3/16:9 50
SDTV (480i) 720x480 4:3/16:9 60
SDTV (576i) 720x576 4:3/16:9 50
55
3D(includingHDMIsignal)
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
SVGA 800x600 4:3 60*/120**
XGA 1024x768 4:3 60*/120**
HD 1280x720 16:9 60*/120**
WXGA 1280x800 16:9 60*/120**
For Video Signal
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
SDTV (480i)*** 720x480 4:3/16:9 60
*60Hzsignalsaresupportedforparallel,up-down,andframesequenceformats.
** 120Hz signals are only supported for frame sequence formats.
***Videosignal(SDTV480i)isonlysupportedforframesequenceformats.
HDMI 3D
Within frame packing formats
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
1080p 1920x1080 16:9 23.98/24
720p 1280x720 16:9 50/59.94/60
Within parallel formats
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
1080i 1920x1080 16:9 50/59.94/60
Within top-down formats
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
1080p 1920x1080 16:9 23.98/24
720p 1280x720 16:9 50/59.94/60
56
Component video
Signal Resolution
(pixels) Aspect Ratio Refresh rate (Hz)
HDTV (1080p) 1920x1080 16:9 50/60
HDTV (1080i) 1920x1080 16:9 50/60
HDTV (720p) 1280x720 16:9 50/60
SDTV (480p) 720x480 4:3/16:9 60
SDTV (576p) 720x576 4:3/16:9 50
SDTV (480i) 720x480 4:3/16:9 60
SDTV (576i) 720x576 4:3/16:9 50
Composite video
Signal Aspect Ratio Refresh rate (Hz)
NTSC 4:3 60
PAL 4:3 50
PAL60 4:3 60
SECAM 4:3 50
57
Copyright information
Copyright
Copyright 2015 All rights reserved. No part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system or translated into any language or computer language, in any form or by any
means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written
permission of ViewSonic.
Disclaimer
ViewSonic does not make any statement or warranty, expressed or implied, for the merchantability and
tness for a particular purpose with respect to any contents within this manual. Additionally, ViewSonic
reserves the right to revise and update the contents of this manual without notice.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Other names would be the
copyrights of the respective companies or organizations.
58
Appendix
IR control table
Button Format Byte1 Byte2 Byte3 Byte4
PgDn NEC X3 F4 05 FA
PgUp NEC X3 F4 06 F9
Blank NEC X3 F4 07 F8
Auto sync NEC X3 F4 08 F7
Up NEC X3 F4 0B F4
Down NEC X3 F4 0C F3
Left NEC X3 F4 0E F1
Right NEC X3 F4 0F F0
Color Mode NEC X3 F4 10 EF
Mute NEC X3 F4 14 EB
Enter NEC X3 F4 15 EA
Power ON NEC X3 F4 17 E8
Presentation Timer NEC X3 F4 27 D8
Exit NEC X3 F4 28 D7
Eco Mode NEC X3 F4 2B D4
Menu NEC X3 F4 30 CF
Mouse NEC X3 F4 31 CE
Mouse Left NEC X3 F4 36 C9
Mouse Right NEC X3 F4 37 C8
Source NEC X3 F4 40 BF
Pattern NEC X3 F4 55 AA
My button NEC X3 F4 56 A9
HDMI NEC X3 F4 58 A7
Volume+ NEC X3 F4 82 7D
Volume- NEC X3 F4 83 7C
Magnify NEC X3 F4 18 e7
Aspect NEC 83 F4 13 EC
Video NEC 83 F4 9F 60
Audio Mode NEC X3 F4 9E 61
COMP NEC X3 F4 41 be
Panel Key Lock NEC X3 F4 8E 71
Help NEC X3 F4 21 DE
5959
Address Code
Code 1 83F4
Code 2 93F4
Code 3 A3F4
Code 4 B3F4
Code 5 C3F4
Code 6 D3F4
Code 7 E3F4
Code 8 F3F4
RS232 command table
＜Pin assignment for this two end＞
Pin Description Pin Description
1 NC 2 RX
3 TX 4 NC
5 GND 6 NC
7 RTSZ 8 CTSZ
9 NC
＜Interface＞
RS-232 protocol
Baud Rate 19200bps (default)
Data Length 8 bit
Parity check None
Stop bit 1 bit
ow control None
60
<RS232 Command List＞
FUNCTION Status Operation cmd
Power supply
Write
Activate 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Read Power status
(ON/OFF) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E
Reset All Settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Reset color
settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87
Splash Screen
Write
Splash Screen - Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash Screen - Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Splash Screen -
ViewSonic 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Splash Screen - Screen
Capture 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x03 0x6A
Splash Screen - OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Read Splash Screen status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68
Quick Power Off
Write
Quick Power Off OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
Quick Power Off ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Read Quick Power Off status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B 0x69
High Altitude
Mode
Write
High Altitude Mode
OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High Altitude Mode ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
Read High Altitude Mode
status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A
light source Mode
Write
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Read light source Mode
status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E
Message
Write
Message OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Message ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85
6161
Projector Position
Write
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Real ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Front ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Read Projector Position
status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F
3D Sync
Write
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
Frame Sequential 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80
Frame Packing 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81
Top-Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82
Side-by-Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83
Read 3D Sync Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F
3D Sync Invert
Write
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
Read 3D Sync Invert Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80
Contrast
Write
Contrast decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Read Contrast 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61
Brightness
Write
Brightness decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Read Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62
62
Aspect ratio
Write
Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Aspect ratio Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67
Aspect ratio Wide 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68
Aspect ratio 2.35:1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x07 0x69
Aspect ratio Panorama 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x08 0x6A
Read Aspect Ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63
Auto Adjust Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Horizontal
position
Write
Horizontal position shift
right /
Horizontal position shift left
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Horizontal position shift
right /
Horizontal position shift left
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Read Horizontal position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65
Vertical
position
Write
Vertical Position shift up /
Vertical Position shift down 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Vertical Position shift up /
Vertical Position shift down 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
Read Read vertical position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66
Color
Temperature
Write
Color Temperature Warm 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
Color Temperature Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
Color Temperature Neutral 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
Color Temperature Cool 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
Read Color Temperature status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67
Blank
Write
Blank ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68
Keystone
Correction -
Vertical
Write
Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Read Keystone Correction status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
6363
Keystone
Correction -
Horizontal
Write
Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E
Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F
Read Keystone Correction
status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31 0x8F
Color mode
Write
Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
ViewMatch 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Dynamic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x08 0x71
Read Preset Mode status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A
Primary color
Write
Original Color R 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Original Color G 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Original Color B 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Original Color C 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Original Color M 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Original Color Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Read Original Color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F
Tint
Write
Color Adjustment
decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Color Adjustment
increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Read Tint 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70
Saturation
Write
Saturation decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Saturation increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Read Saturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71
Gain
Write
Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72
Freeze
Write
Freeze ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60
64
Source input
Write
Input source
VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Input source
VGA2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
Input source
HDMI 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Input source
HDMI/MHL 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67
Input source
Composite video 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Input source
SVIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Read Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61
Quick Auto
Search
Write
Quick Search ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Search OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Read Quick Search status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62
Mute
Write
Mute ON 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Read Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61
Volume
Write
Volume increase 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Volume decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64
6565
Language
Write
ENGLISH 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
FRANÇAIS 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
DEUTSCH 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
ITALIANO 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
ESPAÑOL 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
РУССКИЙ 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
繁體中文 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
English 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
日本語 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
한국어 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
Svenska 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
Nederlands 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
Türkçe 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
Čeština 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E
Português 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
ไทย 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
Polski 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
Suomi 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73
Indonesian 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75
Read Language 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62
light source
Usage Time
Write Reset light source
Usage Time to zero 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Read light source Usage
Time 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63
66
HDMI Format
Write
RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85
YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87
Read HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86
HDMI range
Write
Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88
Read HDMI Range status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29 0x87
CEC
Write
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88
On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89
Read CEC status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B 0x89
Error status Read Read Error status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66
Brilliant Color
Write
Brilliant Color 0 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D
Brilliant Color 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E
Brilliant Color 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x02 0x6F
Brilliant Color 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x03 0x70
Brilliant Color 4 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x04 0x71
Brilliant Color 5 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x05 0x72
Brilliant Color 6 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x06 0x73
Brilliant Color 7 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x07 0x74
Brilliant Color 8 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x08 0x75
Brilliant Color 9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x09 0x76
Brilliant Color 10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x0A 0x77
Read Brilliant Color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0F 0x6E
6767
Remote control
code
Write
Code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0
Code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1
Code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2
Code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3
Code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4
Code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5
Code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6
Code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7
Read Remote Control
Code status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x048 0xAl
Screen Color
Write
Screen Color OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x00 0x8F
Backboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x01 0x90
Green board 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x02 0x91
Whiteboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x03 0x92
Read Screen Color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x32 0x90
Overscan
Write
Overscan OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x00 0x90
Overscan 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x01 0x91
Overscan 2 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x02 0x92
Overscan 3 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x03 0x93
Overscan 4 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x04 0x94
Overscan 5 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x05 0x95
Read Overscan status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x33 0x91
68
Remote Key Write
Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61
Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65
Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D
Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E
Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F
Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60
Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56
Input 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67
Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x08 0x5A
My buttons 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x11 0x63
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region Website T= Telephone
C = CHAT ONLINE Email
Australia
New Zealand www.viewsonic.com.au AUS= 1800 880 818
NZ= 0800 008 822 service@au.viewsonic.com
Canada www.viewsonic.com T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533 service.ca@viewsonic.com
Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com
India www.in.viewsonic.com T= 1800 419 0959 service@in.viewsonic.com
Korea ap.viewsonic.com/kr/ T= 080 333 2131 service@kr.viewsonic.com
Latin America
(Argentina) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Chile) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Columbia) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Mexico) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.
Tel: 55) 6547-6454 55)6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico
Latin America
(Peru) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com
Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com
Puerto Rico &
Virgin Islands www.viewsonic.com
T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/
la/soporte/servicio-tecnico
service.us@viewsonic.com
soporte@viewsonic.com
Singapore/
Malaysia/Thailand www.ap.viewsonic.com T= 65 6461 6044 service@sg.viewsonic.com
South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com
United States www.viewsonic.com T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530 service.us@viewsonic.com
69
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
LimitedOne(1)yearGeneralWarranty
ViewSonic’s standard warranty period is one (1) year for any product model in any
country, unless a longer warranty period is specied and provided by ViewSonic .
Please refer to the ViewSonic website in your country to check the local terms and
model variants, and see if the product model in your country is eligible for a longer
warranty period.
LimitedOne(1)yearHeavyUsageWarranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the Light Source, one (1) year for labor, and ninety (90) days
for the original Light Source from the date of the rst consumer purchase; Europe:
One (1) year warranty for all parts excluding the Light Source, one (1) year for labor,
and ninety (90) days for the original Light Source from the date of the rst consumer
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
ofce for the warranty information.
Light Source warranty subject to terms and conditions, verication and approval.
Applies to manufacturer’s installed Light Source only. All accessory Light Source
purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the rst consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modied or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a. Accident, abuse, misuse, neglect, re, water, lightning, or other acts of nature,
improper maintenance, unauthorized product modication, or failure to follow
instructions supplied with the product.
b. Operation outside of product specications.
c. Operation of the product for other than the normal intended use or not under
normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power uctuations or failure.
h. Use of supplies or parts not meeting ViewSonic’s specications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
70
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
contained herein including the implied warranty of merchantability and tness for a
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of time, loss of prots, loss of
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
This warranty gives you specic legal rights, and you may also have other rights
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
71
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
ViewSonic’s standard warranty period is one (1) year for any product model in any country, unless
a longer warranty period is specied and provided by ViewSonic . Please refer to the ViewSonic
website in your country to check the local terms and model variants, and see if the product model in
your country is eligible for a longer warranty period.
Who the warranty protects:
This warranty is valid only for the rst consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modied or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, re, water, lightning, or other acts of nature, unauthorized product
modication, unauthorized attempted repair, or failure to follow instructions supplied with the
product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power uctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and tness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
inconvenience, loss of use of the product, loss of time, loss of prots, loss of business opportunity,
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
72
ContactInformationforSales&AuthorizedService(CentroAutorizadodeServicio)withinMexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
73
