Table of Contents
- PJD6_Normal_English_0504.pdf
- Introduction
- Using the product
- Connection
- Operation
- Powering on/off the projector
- Adjusting the projector height
- Adjusting the projector zoom and focus
- Adjusting projection image size
- Securing the projector
- Locking control keys
- Setting the presentation timer
- Menu operation
- Controlling the projector through a LAN environment
- Using the projector in standby mode
- Adjusting the sound
- Maintenance
- Specifications
- Appendix
Viewsonic PJD7525W User Manual
Displayed below is the user manual for PJD7525W by Viewsonic which is a product in the Data Projectors category. This manual has pages.
Related Manuals
PJD6250L/PJD6252L/PJD7325/
PJD6550W/PJD6552W/PJD7525W
DLP Projector
User Guide
Model No.
VS15912/VS15913/VS15991/VS15915/VS15916/VS15992
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specic languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Thank you for choosing ViewSonic
With over 25 years as a world leading provider of visual solutions,
ViewSonic is dedicated to exceeding the world’s expectations for
technological evolution, innovation, and simplicity. At ViewSonic, we
believe that our products have the potential to make a positive impact
in the world, and we are confident that the ViewSonic product you have
chosen will serve you well.
Once again, thank you for choosing ViewSonic !
Compliance Information
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage
Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode uorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India) This product complies
with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for
the exemptions set in Schedule 2 of the Rule.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the unit. When a cart is used, use caution
when moving the cart/unit combination to avoid injury from tipping
over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
Copyright Information
Copyright © ViewSonic Corporation, 2015. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic and the three birds logo are registered trademarks of ViewSonic
Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specifications without notice. Information in this
document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name: PJD6250L/PJD6252L/PJD7325/PJD6550W/PJD6552W/
PJD7525W
ViewSonic DLP Projector
Model Number: VS15912/VS15913/VS15991/VS15915/VS15916/VS15992
Document
Number:
PJD6250L/PJD6252L/PJD7325/PJD6550W/PJD6552W/
PJD7525W_UG_ENG Rev. 1A 06-08-15
Serial Number:
Purchase Date:
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
i
FCC notice
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, detectable by turning the
equipment in question off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the distance between the equipment and the receiver
• Connect the equipment to an outlet on a different circuit than that which the receiver
is connected to
• Or consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference that may cause undesired operation.
ii
Safety instructions
Read all of these instructions before you operate your projector and save for future
reference.
1. Read instructions
All the safety and operating instructions should be read before the appliance is
operated.
2. Notes and warnings
All notes and warnings in the operating instructions should be adhered to.
3. Cleaning
Unplug the projector from the wall socket before cleaning. Use a damp cloth for
cleaning the projector housing. Do not use liquid or aerosol cleaners.
4. Accessories
Do not place this product on an unstable cart, stand, or table. The product may fall,
causing serious damage to the product.
Keep the plastic packing materials (from the projector, accessories and optional
parts) out of the reach of children as these bags may result in death by suffocation.
Be particularly careful around the small children.
5. Ventilation
The projector is equipped with ventilation holes (intake) and ventilation holes
(exhaust).
Do not block or place anything near these slots, or internal heat build-up may
occur, causing picture degradation or damage to the projector.
6. Power sources
Check that the operating voltage of your unit is identical with the voltage of your
local power supply.
7. Servicing
Do not attempt to service this projector yourself. Refer all servicing to qualified
service personnel.
8. Replacement parts
When replacement parts are required, be sure that the replacement parts are
specified by the manufacture. Unauthorized substitutions may result in fire, electric
shock or other hazards.
9. Moisture Condensation
Never operate this projector immediately after moving it from a cold location to a
warm one. When the projector is exposed to such a change in temperature,
moisture may condense on the lens and the crucial internal parts. To prevent the
unit from possible damage, do not use the projector for at least 2 hours when there
is an extreme or sudden change in temperature.
iii
Notes on the AC power cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC
outlet, please contact your sales dealer. This projector is equipped with a grounding
type AC line plug. Please ensure that your outlet fits the plug. Do not defeat the safety
purpose of this grounding type plug. We highly recommend using a video source
device also equipped with a grounding type AC line plug to prevent signal interference
due to voltage fluctuations.
For Australia and
Mainland China
For the U.S.A. and
Canada
For the U.K.
Ground
For Continental Europe
Ground
Ground
Ground
Table of contents
iv
Introduction ........................................................................................... 1
Projector features ................................................................................................................................... 1
Package contents .................................................................................................................................. 2
Projector overview ................................................................................................................................. 3
Using the product .................................................................................. 5
Control panel .......................................................................................................................................... 5
Connection ports .................................................................................................................................... 7
Remote control ....................................................................................................................................... 8
Installing the batteries .......................................................................................................................... 12
Remote control operation ..................................................................................................................... 13
Connection .......................................................................................... 14
Connecting a computer or monitor ....................................................................................................... 15
Connecting Video source devices ........................................................................................................ 16
Playing sound through the projector .................................................................................................... 18
Operation ............................................................................................. 19
Powering on/off the projector ............................................................................................................... 19
Adjusting the projector height .............................................................................................................. 20
Adjusting the projector zoom and focus ............................................................................................... 20
Adjusting projection image size ........................................................................................................... 21
Securing the projector .......................................................................................................................... 23
Locking control keys ............................................................................................................................ 25
Setting the presentation timer .............................................................................................................. 26
Menu operation .................................................................................................................................... 27
Controlling the projector through a LAN environment .......................................................................... 44
Using the projector in standby mode ................................................................................................... 50
Adjusting the sound ............................................................................................................................. 50
Maintenance ........................................................................................ 52
Cleaning the lens ................................................................................................................................. 52
Cleaning the projector housing ............................................................................................................ 52
Installing the dust filter (optional accessory) ........................................................................................ 53
Installing the cable management cover (optional accessory) .............................................................. 54
Replacing the lamp .............................................................................................................................. 55
Specifications ...................................................................................... 57
Dimensions .......................................................................................................................................... 58
Ceiling mount installation ..................................................................................................................... 58
Appendix .............................................................................................. 59
LED indicator messages ...................................................................................................................... 59
Compatibility modes ............................................................................................................................. 60
Troubleshooting ................................................................................................................................... 62
RS-232 command and configuration ................................................................................................... 63
IR control table ..................................................................................................................................... 69
1
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
• Compatibility with Macintosh® computers
• Compatibility with NTSC, PAL, SECAM and HDTV
• D-Sub 15-pin terminal for analog video connectivity
• Equipped with HDMI connection supporting HDCP
• Multi-language On-Screen Display (OSD) menus
• Digital keystone correction to correct distorted images
• RS-232 connector for serial control
• Power saving function decreasing the power consumption of the lamp by up to 30%
when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
• Blu-Ray 3D function supported
• Selectable quick power off function
• Color Management allowing color adjustments to your liking
• Screen Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• HDMI CEC (Consumer Electronics Control) function allows synchronized power
ON/OFF operation between the projector and a CEC-compatible DVD player device
connected to the HDMI input of the projector
• LAN setting allowing management of projector status from a remote computer
Note
• The information in this manual is subject to change without notices.
• The reproduction, transfer or copy of all or any part of this document is not permitted
without express written consent.
2
Package contents
When you unpack the projector, make sure you have all these components:
Note
• Contact you dealer immediately if any items are missing, appear damaged, or if the unit
does not work.
• For maximum protection of the product, please save the original shipping carton and
packing materials and repack your product as it was originally packed at the factory if
you need to ship it.
PJD6250L/PJD6252L/PJD7325/
PJD6550W/PJD6552W/
PJD7525W projector
Remote control (IR) &
batteries (AAA *2 PCS) AC power cord
VGA cable (D-SUB to D-SUB)ViewSonic CD wizard Quick start guide
Optional accessories
1. Cable management cover (rear cable cover)
2. Carry bag
3. Dust filter
3
Projector overview
Front view
1. Front IR remote control sensor 2. Projection lens
3. Speaker 4. HDMI/MHL dongle port
5. Ventilation holes 6. Focus ring
7. Zoom ring 8. Control panel
9. Lamp cover
6
8
4
1
97
2
3
5
4
Rear View
Bottom View
Note
• This projector can be used with a ceiling mount for support. The ceiling mount is not
included in the package.
• Contact your dealer for information to mount the projector on a ceiling.
1. Connection ports 2. Kensington lock
3. AC power socket
1. Security bar 2. Ceiling mount holes
123
1
2
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
60.01113.54
65.89
5
Using the product
Control panel
1. POWER
Turn the projector on or off.
2. //// (Keystone)
Manually corrects distorted images resulting from an angled projection.
Up/ Down/ Left/ Right
Selects the desired menu items and makes adjustments.
3. Menu/Exit
Menu: Display or exit the on-screen display menus.
Exit: Goes back to previous OSD menu, exits and saves menu settings.
4. Enter/ (Corner Adj.)
Enacts the selected On-Screen Display (OSD) menu item.
Displays the Corner Adj. page.
5. (My Button)
User definable key for customized function.
6. (Power LED indicator)
Refer to “LED Indicator Messages”.
7. (Temp LED indicator)
Refer to “LED Indicator Messages”.
8. (Lamp LED indicator)
Refer to “LED Indicator Messages”.
9. Color Mode
Select the picture setup mode.
10. Source/ (Help)
Power
Color
Mode
Source /
@
Menu
Exit
Enter
1
2
32
2
4
5
2
6
7
8
10 9
?
6
Source: Display the source selection bar.
Help: Display the HELP menu by a long press for 3 seconds.
7
Connection ports
1. AUDIO OUT
Connect to a speaker or other audio input equipment.
2. AUDIO IN 2 / MIC
Connect an audio output from video equipment / computer or Microphone to this
jack.
Note: The function for switching to Audio in 2 / Microphone in is in OSD
menu.
3. MINI USB
This connector is for firmware update and mouse function support.
4. AUDIO IN 1
Connect an audio output from video equipment or computer to this jack.
5. S-VIDEO
Connect S-Video output from video equipment to this jack.
6. VIDEO
Connect composite video output from video equipment to this jack.
7. COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
8. COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack.
9. RS-232
When operating the projector via a computer, connect this to the controlling com-
puter's RS-232C port.
10. MONITOR OUT
Connect to a computer display, etc.
11. HDMI
Connect HDMI output from video equipment to this jack.
12. LAN
RJ45 connector for Ethernet connection.
13. USB TYPE A
5V/2A out for power charging.
479
13
12
11
10
56 8
3
2
1
8
Remote control
1. Power
Turn the projector on or off.
2. COMP1
Display COMPUTER IN 1 signal.
3. Auto Sync
Automatically determines the best picture timings for the displayed image.
4. //// (Keystone)
Manually corrects distorted images resulting from an angled projection.
Up/ Down/ Left/ Right
Selects the desired menu items and makes adjustments.
5. Laser
Aim the remote at the viewing screen, press and hold this button to activate the
laser pointer.
6. Menu
Display on-screen display menus.
7. (Right mouse)
Perform the right button of the mouse when mouse mode is activated.
8. (Left mouse)
Perform the left button of the mouse when mouse mode is activated.
9. Mouse
15
16
17
18
19
23
24
4
20
21
22
26
25
27
28
4
4
6
8
10
11
9
3
7
5
4
12
13
14
9
Switch between the normal and mouse modes.
10. (Lock)/ID Set
Lock: Activates or disables panel key lock.
ID Set: Sets remote control code.
11. (Timer)
Activate P-Timer OSD menu.
12. (Volume+)
Increase the volume level.
13. Eco Mode
Switch the lamp mode from Normal, Economic, Dynamic to Sleep.
14. (Volume-)
Decrease the volume level.
15. (My Button)
User definable key for customized function.
16. HDMI
Display HDMI signal.
17. COMP2
Not available for PJD5 series.
18. Source
Display the source selection bar.
19. Enter/ (Corner Adj.)
Enacts the selected On-Screen Display (OSD) menu item.
Displays the Corner Adj. page.
20. Exit
Goes back to previous OSD menu, exits and saves menu settings.
21. (Page Up)
Perform page up function when mouse mode is activated.
22. (Page Down)
Perform page down function when mouse mode is activated.
23. Pattern
Display embedded test pattern.
24. Blank
Hide the screen picture.
25. (Help)
Display the Help menu.
26. (Magnify)
Displays the zoom bar that magnifies or reduces the projected picture size.
27. Color Mode
Select the picture setup mode.
28. (Mute)
Toggles the projector audio between on and off.
?
10
Operating the Laser pointer
The laser beam is visible. It is necessary to press and
hold LASER for continuous output.
The laser pointer is not a toy. Parents should be mindful of
the dangers of laser energy and keep this remote control
out of the reach of children.
Caution
• Do not look into the laser light window or shine the laser light beam on yourself or
others. See the warning messages on the back of the remote control prior to using it.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connection" on page 14
for details.
2. Set the input signal to COMPUTER.
3. Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse
mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press / / / .
• To left-click, press .
• To right-click, press .
• To operate your display software program (on a connected PC) which responds
to page up/down commands (like Microsoft PowerPoint), press Page Up/Page
Down.
• To return to the normal mode, press Mouse again or other keys except for the
mouse related multi-function keys.
Remote control code
The projector can be assigned to 8 different remote control
codes, 1 to 8. When several adjacent projectors are in
operation at the same time, switching the remote control
codes can prevent interference from other remote
controls. Set the remote control code for the projector first
before changing that for the remote control.
To switch the code for the projector, select from among 1
to 8 in the SYSTEM SETTING: ADVANCED > Remote
Control Code menu.
11
To switch the code for the remote control, press ID set and the corresponding button
from 1 to 8 buttons on the remote control together for 5 seconds or more. The initial
code is set to1. When the code is switched to 8, the remote control can control every
projector.
Note
• If different codes are set on the projector and remote control, there will be no response
from the remote control. When that happens, switch the code for the remote control
again.
12
Installing the batteries
1. Open the battery cover in the
direction shown.
2. Install batteries as indicated by the
diagram inside the compartment.
3. Close the battery cover into position.
Caution
• Risk of explosion if battery is replaced by an incorrect type.
• Dispose of used batteries according to the instructions.
• Make sure the plus and minus terminals are correctly aligned when loading a battery.
Note
• Keep the battery out of the reach of children.
• Remove batteries from remote control when not using for extended periods.
• Do not recharge the battery or expose the battery to fire or water.
• Do not dispose the used battery along with household waste. Dispose
used batteries
according to local regulations.
• Danger of explosion may happen if batteries are incorrectly replaced. Replace only with
the same type recommended by the manufacturer.
• Battery should not be in or near to fire or water, keep batteries in a dark, cool and dry
place.
• If suspect battery leakage, wipe out the leakage and then replace a new battery. If the
leakage adheres to your body or clothes, rinse well with water immediately.
13
Remote control operation
Point the remote control at the infrared remote sensor and press a button.
• Operating the projector from the
front.
Note
• The remote control may not operate when there is sunlight or other strong light such as
a fluorescent lamp shining on the remote sensor.
• Operate the remote control from a position where the remote sensor is visible.
• Do not drop the remote control or jolt it.
• Keep the remote control out of locations with excessively high temperature or humidity.
• Do not get water on the remote control or place wet objects on it.
• Do not disassemble the remote control.
7m
5m
15 15
8m
14
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
Important
• In the connections shown above, some cables may not be included with the projector
(see "Package contents" on page 2). They are commercially available from electronics
stores.
• The connection illustrations above are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
• For detailed connection methods, see pages 15-17.
1. Audio cable 2. Microphone 3.5 mini jack cable
3. VGA (D-Sub) to HDTV (RCA) cable 4. S-Video cable
5. Composite Video cable 6. HDMI cable
7. USB cable (mini-B type to A type) 8. VGA cable (D-Sub to D-Sub)
9. VGA to DVI-A cable 10. HDMI/MHL dongle
2
13
1
456
7889
1
10
15
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
Important
• Many notebooks do not turn on their external video ports when connected to a
projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display
on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol
on the notebook. Press FN and the labeled function key simultaneously. Refer to your
notebook's documentation to find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the MONITOR OUT signal output socket on the projector to an
external monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1. Connect the projector to a computer as described in "Connecting a computer" on
page 15.
2. Take a suitable VGA cable (only one supplied) and connect one end of the cable to
the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3. Connect the other end of the cable to the MONITOR OUT socket on the projector.
Important
• In standby mode, the MONITOR OUT output only works when COMPUTER IN 1 is
made to the projector.
16
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
•HDMI
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the
above connecting methods, however each provides a different level of video quality.
The method you choose will most likely depend upon the availability of matching
terminals on both the projector and the Video source device as described below:
Connecting an HDMI source device
Examine your Video source device to determine if it has a set of unused HDMI output
jacks available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an HDMI source device:
1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI
source device.
2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
Terminal name Terminal appearance Reference Picture quality
HDMI
HDMI "Connecting an
HDMI source
device" on page 16
Best
Component Video
COMPUTER IN 1/
COMPUTER IN 2
"Connecting a
Component Video
source device" on
page 16
Better
S-Video
S-VIDEO "Connecting an S-
Video source
device" on page 17
Good
Video
VIDEO "Connecting a
composite Video
source device" on
page 17
Normal
17
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1. Take a VGA (D-Sub) to HDTV (RCA) cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2. Connect the other end of the cable (with a D-Sub type connector) to the COM-
PUTER IN 1 or COMPUTER IN 2 socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1. Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2. Connect the other end of the S-Video cable to the S-VIDEO socket on the projec-
tor.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to
this device using an S-Video connection as this makes an unnecessary second
connection of poorer picture quality. See "Connecting Video source devices" on page
16 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
18
1. Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
2. Connect the other end of the Video cable to the VIDEO socket on the projector.
Important
• If the selected video image is not displayed after the projector is turned on and the
correct video source has been selected, check that the Video source device is turned on
and operating correctly. Also check that the signal cables have been connected
correctly.
• You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source
devices" on page 16 for details.
Playing sound through the projector
You can make use of the projector (mixed mono) speaker in your presentations, and
also connect separate amplified speakers to the AUDIO OUT socket of the projector.
If you have a separate sound system, you will most likely want to connect the audio
output of your Video source device to that sound system, instead of to the mono audio
projector.
You can also use a microphone to output the sound through the projector speaker
when the SYSTEM SETTING: ADVANCED > Audio Settings > Audio In 2 menu is
set to Microphone. See "Adjusting the Audio In 2 setting" on page 51 for details.
Once connected, the audio can be controlled by the projector On-Screen Display
(OSD) menus. See "Adjusting the sound" on page 50 for details.
About the microphone input
• If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the
projector.
• There are two ways to adjust microphone volumes.
• Directly set microphone volume levels in the SYSTEM SETTING: ADVANCED
> Audio Settings > Microphone Volume menu.
• Set projector volume levels in the SYSTEM SETTING: ADVANCED > Audio
Settings > Audio Volume menu, or press Volume keys (+, -) on the remote
control. (The projector volume setting will affect the microphone volume.)
• To make the microphone input available when the projector is in standby mode, turn
on the SYSTEM SETTING: ADVANCED > Audio Settings > Active Audio out
menu.
• If the microphone is not working, check the volume setting and cable connection.
• You might get feedback noise from the microphone when you are too close to the
speaker of the projector. Move the microphone away from the speaker of the
projector. The greater volume you require, the greater distance you need to be
away from the Speaker to prevent the noise.
19
Operation
Powering on/off the projector
Powering on the projector:
1. Complete the AC power cord and peripheral signal cable(s) connections.
2. Press to turn on the projector.
The projector takes a minute or so to warm up.
• If the projector is still hot from previous activity, it will run the cooling fan for
approximately 60 seconds before energizing the lamp.
3. Turn on your source (computer, notebook, DVD, etc.).
• If you are connecting multiple sources to the projector simultaneously, press
Source to select your desired signal or press your desired signal key on the
remote control.
• If the projector doesn't detect a valid signal, the message 'No Signal' will con-
tinue to be displayed.
• Be sure the Quick Auto Search function in the SOURCE menu is On if you
want the projector to automatically search for the signals.
Warning
• Never look into the lens when the lamp is on. This can damage your eyes.
• This focal point concentrates high temperature. Do not place any object near it to avoid
possible fire hazard.
Powering off the projector:
1. Press to turn off the projector lamp. You will see a message "Power off? Press
Power again" appear on the screen.
2. Press again to confirm.
• When Active VGA out/Active Audio out function is turned off, the Power LED
begins flashing and the projector has entered stand-by mode.
• When Active VGA out/Active Audio out function is turned on, the Power LED
becomes steady light and the projector has entered stand-by mode.
• If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-by
mode, simply press to restart the projector.
3. Disconnect the AC power cord from the electrical outlet and the projector.
4. Do not turn on the projector right after power off.
20
Adjusting the projector height
The projector is equipped with an elevator foot to adjust the image height. To raise or
lower the image, turn the elevator foot to fine-tune the height.
Note
• To avoid damaging the projector, make sure that the elevator foot is fully retracted
before placing the projector in its carrying case.
Adjusting the projector zoom and focus
1. Sharpen the image by rotating the focus ring.
2. Adjust the image size by rotating the zoom ring or moving the projector forward or
backward.
Elevator foot
Focus ring
Zoom ring
21
Adjusting projection image size
Refer to the graphic and table below to determine the screen size and projection
distance.
PJD6250L/PJD6252L/PJD7325
PJD6550W/PJD6552W/PJD7525W
4 : 3 Screen diagonal
Screen size Projection distance
[inch (m)] Vertical offset
[inch (cm)]
Diagonal
[inch (cm)]
W
[inch (cm)]
H
[inch (cm)] (min.) (max.)
30 (76) 24 (61) 18 (46) 47 (1.2) 51 (1.3) 2.7 (6.9)
40 (102) 32 (81) 24 (61) 62 (1.6) 69 (1.7) 3.6 (9.1)
60 (152) 48 (122) 36 (91) 94 (2.4) 103 (2.6) 5.4 (13.7)
80 (203) 64 (163) 48 (122) 125 (3.2) 137 (3.5) 7.2 (18.3)
100 (254) 80 (203) 60 (152) 156 (4.0) 172 (4.4) 9.0 (22.9)
150 (381) 120 (305) 90 (229) 234 (5.9) 257 (6.5) 13.5 (34.3)
200 (508) 160 (406) 120 (305) 312 (7.9) 343 (8.7) 18.0 (45.7)
250 (635) 200 (508) 150 (381) 390 (9.9) 429 (10.9) 22.5 (57.2)
300 (762) 240 (610) 180 (457) 468 (11.9) 515 (13.1) 27.0 (68.6)
16 : 10 Screen diagonal
Screen size Projection distance
[inch (m)] Vertical offset
[inch (cm)]
Diagonal
[inch (cm)]
W
[inch (cm)]
H
[inch (cm)] (min.) (max.)
30 (76) 26 (65) 16 (40) 36 (0.9) 46 (1.2) 1.2 (3.0)
40 (102) 34 (86) 21 (54) 49 (1.2) 61 (1.5) 1.6 (4.1)
60 (152) 51 (130) 32 (81) 75 (1.9) 93 (2.4) 2.4 (6.1)
80 (203) 68 (173) 42 (108) 100 (2.5) 124 (3.2) 3.2 (8.1)
100 (254) 85 (216) 53 (135) 126 (3.2) 156 (4.0) 4.0 (10.1)
150 (381) 128 (324) 80 (202) 189 (4.8) 235 (6.0) 6.0 (15.2)
200 (508) 170 (432) 106 (269) 253 (6.4) 313 (8.0) 8.0 (20.2)
250 (635) 213 (540) 133 (337) 317 (8.0) 392 (10.0) 10.0 (25.3)
300 (762) 255 (648) 159 (404) 380 (9.7) - 12.0 (30.4)
Diagonal size
Projection distance
Center of lens
Screen
Vertical offset
W
H
22
Note
• Position the projector in a horizontal position; other positions can cause heat build-up
and damage to the projector.
• Keep a space of 30 cm or more between the sides of the projector.
• Do not use the projector in a smoky environment. Smoke residue may build-up on
critical parts and damage the projector or its performance.
23
Securing the projector
Setting a password
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Advanced
> Security Settings menu. Press Enter. The Security Settings page displays.
2. Highlight Change Password and press Enter.
3. According to the password you desire to set, press the arrow keys to enter six
digits for the password.
4. Confirm the new password by re-entering the new password.
5. Go back to SYSTEM SETTING: ADVANCED > Advanced > Security Settings >
Power on Lock menu, and press Enter. You will be asked to input password.
Once the password is set, the OSD menu returns to the Power on Lock. Select
On by pressing / .
6. To leave the OSD menu, press Menu/Exit.
Entering the password recall procedure
If the password function is activated, you will be asked to enter the six-digit password
every time you turn on the projector.
1. If you enter an incorrect password 5 times in succession, the projector will display
a coded number on the screen when you press the auto key 3~5 seconds.
2. Write down the number and turn off your projector.
3. Seek help from the local ViewSonic service center to decode the number. You may
be required to provide proof of purchase documentation to verify that you are an
authorized user of the projector.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Advanced
> Security Settings > Change Password menu and press Enter.
2. Enter the old password.
• If the password is correct, another message "NPUT NEW PASSWORD" dis-
plays.
• If the password is incorrect, the password error message displays, and the
message "INPUT CURRENT PASSWORD" displays for your retry. You can
press Menu/Exit to cancel the change or try another password.
3. Enter a new password.
4. Confirm the new password by re-entering the new password.
5. You have successfully assigned a new password to the projector. Remember to
enter the new password next time the projector is started.
6. To leave the OSD menu, press Menu/Exit.
24
Disabling the password function
To disable password protection, go back to SYSTEM SETTING: ADVANCED >
Advanced > Security Settings > Power on Lock menu, and press Enter. You will be
asked to input password. Once the password is set, the OSD menu returns to the
Power on Lock. Select Off by pressing / . To leave the OSD menu, press Menu/
Exit.
25
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is On, no control keys on the projector will operate except Power.
1. Press Lock on the remote control for 3 seconds.
Press Lock on the remote control, a confirmation
message "Are you sure to lock panel keys?" is
displayed. Select Yes to confirm.
To release panel key lock:
1. Press Lock on the remote control directly. The
Panel keys are unlock.
Important
• If you press Power to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
• Keys on the remote control are still functional when panel key lock is enabled.
26
Setting the presentation timer
The presentation timer can indicate the presentation time on the screen to help you
achieve better time management when giving presentations. Follow these steps to
utilize this function:
1. Press Timer on the remote control to access the
Presentation Timer menu or go to the SYSTEM
SETTING: BASIC > Advanced > Presentation Timer
menu and press Enter to display the Presentation
Timer page.
2. Highlight Timer Period and decide the timer period by
pressing / .
3. Press to highlight Timer Display and choose if you
want the timer to show up on the screen by pressing / .
4. Press to highlight Timer Position and set the timer position by pressing / .
Top-Left →Bottom-Left →Top-Right →Bottom-Right
5. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / ..
6. Press to highlight Sound Reminder and select your desired counting direction
by pressing / . If you select On, a double beep sound will be heard at the last
30 seconds of counting down/up, and a triple beep sound will be produced when
the timer is up.
7. To activate the presentation timer, press to highlight Start Counting and select
Yes.
8. To cancel the timer, highlight Start Counting and select No.
Selection Description
Always Displays the timer on screen throughout the presentation time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never Hides the timer throughout the presentation time.
Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decrease from the preset time to 0.
27
Menu operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
How to operate
1. Press Menu to open the OSD menu.
2. When OSD is displayed, use / to select any feature in the main menu.
3. After selecting the desired main menu item, press to enter sub-menu for feature
setting.
4. Use / to select the desired item and adjust the settings with / .
5. Press Menu, the screen will return to the main menu or go back to the upper level
of the menu.
28
Menu tree
Main Menu Sub Menu Settings
DISPLAY
Screen Color Off / Blackboard / Greenboard / Whiteboard
Aspect Ratio
(1) PJD6250L/PJD6252L/PJD7325:
Auto / 4:3 / 16:9 / Anamorphic / 2.35:1
(2) PJD6550W/PJD6552W/PJD7525W:
Auto / 4:3 / 16:9 / Panorama / Anamorphic / 2.35:1
/ 16:10
Keystone -30 - 30
Corner Adj. Top-Right / Top-Left / Bottom-Left / Bottom-Right
Position X: -5 - 5
Y: - 5 - 5
Phase 0 - 31
H. Size -15 - 15
Zoom PC: 0.8X - 2.0X
Video: 0.8X - 1.8X
PICTURE
Color Mode Brightest / Dynamic / Standard / ViewMatch /
Movie
Brightness 0 - 100
Contrast -50 - 50
Color Temp.
Warm / Normal / Neutral / Cool
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
OverScan Off / 1 / 2 / 3 / 4 / 5
HDMI Settings HDMI Format Auto / RGB / YUV
HDMI Range Auto / Enhanced / Normal
Advanced
Tint -50 - 50
Color -50 - 50
Sharpness 0 - 31
Gamma 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8
Brilliant Color Off / 1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
/ 10
Noise Reduction 0 - 31
Color Manage-
ment
Primary color R / G / B / C / M
/ Y
Hue -99 - 99
Saturation 0 - 199
Gain 5 - 195
Reset Color Set-
tings Reset / Cancel
29
SOURCE
Quick Auto
Search Off / On
3D Settings 3D Sync
Auto
Off
Frame Sequential
Frame Packing
Top-Bottom
Side-by-Side
3D Sync Invert Disable /Invert
Standby Settings
Active VGA out Off / On
Active Audio out Off / On
LAN Control Off / On
Auto Power On
Computer Disable/ Enable
CEC Disable/ Enable
Direct Power On Off / On
Power Saving
Auto Power Off Disable / 10 / 20 / 30 min
Sleep Timer Disable / 30 min / 1 hr / 2 hr / 3
hr / 4 hr / 8 hr / 12 hr
Smart Restart Energy Saving Enable / Disable
Disable / Enable
Quick Power Off Disable / Enable
LAN Control
Settings
LAN Settings DHCP on / Static IP
Projector IP
Address
Subnet Mask
Default Gateway
DNS Server
Apply
30
SYSTEM
SETTING:
BASIC
Language
Projector Posi-
tion
Front Table / Rear Table / Rear
Ceiling / Front Ceiling
Menu Settings
Menu Display
Time
5 sec / 10 sec / 15 sec / 20 sec
/ 25 sec / 30 sec
Menu Position Center / Top-Left / Top-Right /
Bottom-Left / Bottom-Right
Blank Timer Disable / 5 min / 10 min / 15
min / 20 min / 25 min / 30 min
Splash Screen Black / Black / ViewSonic / Off
My Button
Auto Sync / Projector Position / Menu Position /
Color Temp. / Brightness / Contrast / 3D Settings /
Screen Color / Splash Screen / Message / Quick
Auto Search / CEC / Audio Mode / Lamp Mode /
DCR / Closed Caption / Power Saving /Informa-
tion
Advanced
Pattern Off / 1 / 2 / 3
Message On / Off
Presentation
Timer
Timer Period 1 ~ 240 min
Timer Display
Always / 1 min /
2 min / 3 min /
Never
Timer Position
Top-Left /
Bottom-Left /
Top-Right /
Bottom-Right
Timer Count-
ing Direction
Count Down /
Count Up
Sound
Reminder On / Off
Start Count-
ing / Off Yes / No
31
SYSTEM
SETTING:
ADVANCED
High Altitude
Mode Off / On
DCR Off / On
Audio Settings
Audio Mode Standard / Speech /
Entertainment
Mute Off / On
Audio Volume 0 - 20
Audio In 2 Audio / Microphone
Microphone
Volume 0 - 10
Power On/Off
Ring Tone On / Off
Closed Caption Off / CC1 / CC2 / CC3 / CC4
Lamp Settings
Lamp Mode Normal / Eco / Dynamic /
SuperEco
Reset Lamp
Hours Reset / Cancel
Lamp Hours
Filter Settings
Filter Mode Off / On
Reset Filter
Hours Reset / Cancel
Filter Hours
Remote Control
Code
1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 (All)
Advanced Security Settings
Change Password
Power on
Lock Off / On
Panel Key Lock Off / On
Reset Settings Reset / Cancel
INFORMATION
Current System Status
Source
Color Mode
Resolution
Color System
Lamp Hours
Filter Hours
IP Address
MAC Address
Firmware Version
32
DISPLAY
Screen Color
The Screen Color feature can help correct the projected picture’s colors to prevent
possible color difference between the source and projected pictures.
There are several precalibrated colors to choose from: Whiteboard, Greenboard, and
Blackboard.
Aspect Ratio
Select how the picture fits on the screen:
PJD6250L/PJD6252L/PJD7325:
•Auto:
Scales an image proportionally to fit the projector's native resolution in its horizontal
or vertical width. You want to make most use of the screen without altering the
source image’s aspect ratio.
• 4:3:
Scales an image so that it is displayed in the center of the screen with a 4:3 aspect
ratio, as it displays them without aspect alteration.
• 16:9:
Scales an image so that it is displayed in the center of the screen with a 16:9 aspect
ratio, as it displays them without aspect alteration.
• Anamorphic:
Scales a 16:9 aspect image vertically and horizontally in a non-linear manner so
that it fills the screen with a 4:3 aspect ratio.
• 2.35: 1
Scales an image so that it is displayed in the center of the screen with a 2.35:1
aspect ratio without aspect alteration.
PJD6550W/PJD6552W/PJD7525W:
•Auto:
Scales an image proportionally to fit the projector's native resolution in its horizontal
or vertical width. You want to make most use of the screen without altering the
source image’s aspect ratio.
• 4:3:
Scales an image so that it is displayed in the center of the screen with a 4:3 aspect
ratio, as it displays them without aspect alteration.
• 16:9:
Scales an image so that it is displayed in the center of the screen with a 16:9 aspect
ratio, as it displays them without aspect alteration.
• Panorama
Scales a 4:3 image vertically and horizontally in a non-linear manner so that it fills
the screen.
33
• Anamorphic:
Scales a 2.35:1 aspect image so that it fills the screen.
• 2.35: 1
Scales an image so that it is displayed in the center of the screen with a 2.35:1
aspect ratio without aspect alteration.
• 16:10:
Scales an image so that it is displayed in the center of the screen with a 16:10
aspect ratio,as it displays them without aspect alteration.
Keystone
Manually correct distorted images resulting from an angled projection.
Press Keystone /// on the projector or remote control to display the Keystone
correction page.
Press to correct keystone at the top of the image.
Press to correct keystone at the bottom of the image.
Press to correct keystone at the left of the image.
Press to correct keystone at the right of the image.
Corner Adj.
Manually adjust four corners of the image by setting the horizontal and vertical values.
1. Press / / / to select one of the four corners and press Enter.
2. Press / to adjust vertical values.
3. Press / to adjust horizontal values.
Position
Displays the position adjusent page. This function is only available when a PC type
input signal is selected.
Phase
Adjusts the clock phase to reduce image distortion. This function is only available
when a PC type input signal is selected.
H. Size
Adjusts the horizontal width of the image. This function is only available when a PC
type input signal is selected.
Zoom
Using the remote control
1. Press on the remote control to display the Zoom bar.
2. Press / to magnify the picture to a desired size.
3. Press repeatedly to magnify the picture to a desired size.
4. To navigate the picture, press Enter to switch to the paning mode and press the
directional arrows ( , , , ) to navigate the picture.
34
5. To reduce size of the picture, press Enter to switch back to the zoom in/out
functionality, and press Auto Sync to restore the picture to its original size. You
can also press repeatedly until it is restored to the original size.
Using the OSD menu
1. Press Menu and then press until the DISPLAY menu is highlighted.
2. Press to select Zoom and press Enter. The Zoom bar displays.
3. Repeat steps 3-5 in the section of Using the remote control above.
35
PICTURE
Color Mode
There are many factory presets optimized for various types of images.
• Brightest: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required.
• Dynamic: Is designed for presentations under daylight environment to match PC
and notebook coloring. In addition, the projector will optimize the image quality
using the dynamic PC function in accordance with the projected contents.
• Standard: Is designed for presentations under daylight environment to match PC
and notebook coloring.
• ViewMatch: Switches between high brightness performance and accurate color
performance.
• Movie: Is appropriate for playing colorful movies. This mode is suitable for viewing
in a blackened (little light) environment
Brightness
Brighten or darken the image.
Contrast
Sets the difference between light and dark areas.
Color Temp.
Sets a color temperature from Warm, Normal, Neutral and Cool.
• Cool: With the highest color temperature, Cool makes the image appear the most
bluish white than other settings.
• Neutral: Makes images appear bluish white.
• Normal: Maintains normal colorings for white.
• Warm: Makes images appear reddish white.
• Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green, and
Blue.
• Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red, Green,
and Blue.
OverScan
OverScan function removes the noise in a video image. Overscan the image to
remove video encoding noise on the edge of video source.
HDMI Settings
HDMI Format
Selects appropriate HDMI format automatically or manually.
Note
• This function is only available when the HDMI-input port is in use.
HDMI Range
36
• Enhanced : The range for HDMI output signal is from 0 - 255.
• Normal: The range for HDMI output signal is from 16 - 235.
Advanced
Tint
Adjusts the red and green color tones of the image.
Color
The higher the value, the more reddish the picture becomes. The lower the value, the
more greenish the picture becomes.
Sharpness
Adjusts the image to make it look sharper or softer.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
Brilliant Color
This adjustable item utilizes a new color-processing algorithm and system level
enhancements to enable higher brightness while providing true, more vibrant colors in
picture. The range is from “1” to “10”. If you prefer a stronger enhanced image, adjust
toward the maximum setting. For a smoother, more natural image, adjust toward the
minimum setting.
Noise Reduction
This function reduces electrical image noise caused by different media players. The
higher the setting, the less the noise.
Color Management
The Color Management provides six sets (RGBCMY) of colors to be adjusted. When
you select each color, you can independently adjust its hue, saturation and gain
according to your preference.
Reset Color Settings
Reset the Color Mode settings of the current input source to default values.
37
SOURCE
Quick Auto Search
Automatically scan through all the input source if the function in the OSD menu is On.
The function will stop the signal auto scan process and fix the signal source you
preferred if you turn Off the Quick Auto Search.
3D Settings
This projector features a 3D function which enables you to enjoy the 3D movies, vid-
eos, and sporting events in a more realistic way by presenting the depth of the
images. You need to wear a pair of 3D glasses to view the 3D images.
3D Sync
When you discover the inversion of the image depth, enable this function to correct
the problem.
3D Sync Invert
When you discover the inversion of the image depth, enable this function to correct
the problem.
Standby Settings
Active VGA out
Set whether the VGA out function works when the projector is in standby (powered off
but connected to AC power). When selecting On, COMPUTER IN 1 will be output.
When selecting Off, power consuption is under 0.5W.
Active Audio out
Set whether the audio out function works when the projector is in standby (powered
off but connected to AC power). When selecting On, AUDIO IN1 will be output.
AUDIO OUT port is also active (from AUDIO IN 1). When selecting Off, power
consuption is under 0.5W. When selecting Off, both AUDIO IN and AUDIO OUT are
Off.
LAN Control
Set whether the network function works when the projector is in standby (powered off
but connected to AC power).
Note
• Less than o.5W power consumption when LAN Control is turned Off.
• When Power Saving is On, the Active VGA out and Active Audio out settings are not
available.
Auto Power On
Computer
Selecting Enable the projector will turn on automatically when COMPUTER signal is
detected.
38
CEC
This projector supports CEC (Consumer Electronics Control) function for synchro-
nized power on/off operation via HDMI connection. That is, if a device that also sup-
ports CEC function is connected to the HDMI input of the projector, when the
projector’s power is turned off, the power of the connected device will also be turned
off automatically. When the power of the connected device is turned on, the projector’s
power will be turned on automatically.
Note
• When connected to the HDMI input of the projector via an HDMI cable, and its CEC
function is turned on.
• Depending on the connected device, the CEC function may not work.
• The function can't be enabled when Active VGA out/Active Audio out function is
disabled.
Direct Power On
Selecting On the projector will turn on automatically after the power cord has been
connected and power has been applied.
Auto Power Off
Power Saving
The projector lowers the projector power if no input source is detected after 5 minutes
to prevent unnecessary waste of lamp life. You can further decide if you would like the
projector to turn off automatically after a set period of time.
When Disable is selected, the projector power will be reduced to 30% after no signal
is detected for 5 minutes.
If you select 10 min, 20 min or 30 min, the projecter power will be reduced to 30%
after no signal is detected for 5 minutes. And when 10 min, 20 min or 30 min is up,
the projector will turn off automatically.
Sleep Timer
This function allows the projector to turn off automatically after a set period of time to
prevent unnecessary waste of lamp life.
Smart Restart
It takes some time to initate this function. Make sure the projector has been turned on
for more than 4 minutes. If the projector is resumed by using the Smart Restart fea-
ture, this function can be executed immediately.
Quick Power Off
• Enable: Quick power on function speeds up the cooling process when turning off
the projector.
• Disable: Turn off with cooling procedure.
Note
• When Disable is selected, the Smart Restart function will be automatically turned Off.
39
LAN Control Settings
Allow you to configure the wired LAN settings. Refer to page 44.
• LAN Settings:
• When selecting “DHCP on”, “Projector IP Address”, “Subnet Mask”, "Default
Gateway" and "DNS Server" will be gray out.
• When selecting "Static IP", “Projector IP Address”, “Subnet Mask”, "Default
Gateway" and "DNS Server" will be available.
• Projector IP Address: Numerical address to identify networked computers.
• The IP Address is the number that identifies this projector on the network. You
cannot have two devices with the same IP Address on the same network.
• The IP Address “0.0.0.0” is prohibited.
• Subnet Mask: A numeric value to define the number of bits used for a network
address of a divided network (or subnet) in an IP Address.
• The Subnet Mask “0.0.0.0” is prohibited.
• Default Gateway: A server (or router) to communicate across networks (subnets)
that are divided by Subnet Mask.
• DNS Server: Setup DNS server address when DHCP is disable.
• Apply: Save and execute the wired LAN settings.
40
SYSTEM SETTING: BASIC
Language
Select the language used by the on-screen menu.
Projector Position
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Menu Settings
Menu Display Time
Duration of OSD menu display countly starts (at idle state by second).
Menu Position
Choose the menu location on the display screen.
Blank Timer
Sets the image blank time when the Blank Timer feature is activated, once elapsed
the image will return to the screen.
Splash Screen
Allows you to select which logo screen will display during projector start-up.
My Button
Allow user to define a short cut key on the remote control, and the function item is
selected in OSD menu. Available options are: Auto Sync, Projector Position, Menu
Position, Color Temp., Brightness, Contrast, 3D Settings, Screen Color, Splash
Screen, Message, Quick Auto Search, CEC, Audio Mode, Lamp Mode, DCR, Closed
Caption, Power Saving and Information.
Advanced
Pattern
Display embedded test pattern.
Message
Enable or disable the message box at the right bottom of the screen.
Presentation Timer
Remind the presenter to finish the presentation within a certain time frame. See "Set-
ting the presentation timer" on page 26.
41
SYSTEM SETTING: ADVANCED
High Altitude Mode
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
DCR
DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio by
darkening the black scenes. Disable DCR will resume to normal contrast
performance. DCR will impact lamp life and system noise performance.
Audio Settings
See "Adjusting the sound" on page 50 for details.
Audio Mode
Press / to select a preferred audio mode.
Mute
Cuts off the sound temporarily.
Audio Volume
Adjusts the projector’s volume level.
Audio In 2
Switch Audio In 2 function for Audio in or Microphone in function.
Microphone Volume
Adjust the microphone’s volume level.
Power On/Off Ring Tone
Setting the sound mute or changing the sound level will not affect the Power On/Off
Ring Tone. The only way to change Power On/Off Ring Tone is setting On or Off here.
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or Off.
Lamp Settings
Lamp Mode
Sets the Lamp Mode.
• Normal: 100% lamp power
• Economic: 80% lamp power
• Dynamic: 30~100% lamp power based on signal
• Sleep: 30% lamp power
Reset Lamp Hours
42
Reset the lamp Hour to 0 hours.
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Filter Settings (Optional)
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
Reset Filter Hours
Reset the filter Hour to 0 hours.
Filter Hours
Display the filter’s elapsed operating time (in hours).
Remote Control Code
See "Remote control code" on page 10 for details.
Advanced
Security Settings
• Change Password: Allows you to set or change the password.
• Power on Lock: If you enable this function, you will have to enter the password next
time you turn on the projector.
See "Securing the projector" on page 23 for details.
Panel Key Lock
Disables or enables all panel key functions except Power on the projector and keys on
the remote control. See "Locking control keys" on page 25 for details.
Reset Settings
Restore settings to factory default. The following settings will still remain: Keystone,
Language, Projector Position, High Altitude Mode, Security Settings, Remote Control
Code.
43
INFORMATION
Current System Status
Shows the currect system status.
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the Color Mode menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Lamp Hours
Displays the number of hours the lamp has been used.
Filter Hours
Displays the number of hours the filter has been used.
IP Address
Display the IP address.
MAC Address
Display the MAC address.
Firmware Version
Shows firmware version.
44
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when
they are properly connected to the same local area network.
If you are in a DHCP on environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the
projector and the other end to the RJ45 port on your Ethernet or router.
2. Press Menu and then go to SOURCE > LAN Control Settings menu.
3. Make sure the LAN Settings is DHCP on.
4. Press to highlight Apply and press Enter.
5. Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page.
The Projector IP Address, Subnet Mask, Default Gateway and DNS Server
settings will be displayed. Note down the IP address displayed in the Projector IP
Address row.
Important
• If the Projector IP Address still does not appear, contact your network administrator.
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway and DNS
Server information when the projector is on.
If you are in a Static IP environment:
1. Repeat steps 1-2 above.
2. Make sure the LAN Settings is Static IP.
3. Contact your ITS administrator for information on the Projector IP Address,
Subnet Mask, Default Gateway, and DNS Server settings.
4. Press to select the item you want to modify and press Enter.
5. Press / to move the cursor and the enter the value.
6. To save the settings, press Enter. If you do not want to save the settings, press
Exit.
7. Press to highlight Apply and press Enter.
Internet
IP Router
45
Important
• If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
• If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway and DNS
Server information when the projector is on.
Controlling the projector remotely through a web browser
Once you have the correct IP address for the projector and the projector is on or in
standby mode, you can use any computer that is on the same local area network to
control the projector.
• If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
• The screen shots in this manual are for reference only, and may differ from the actual
design.
1. Enter the address of the projector in the address bar of your browser and press
Enter.
2. The main page of the Network Control appears.
• Accessing to Network Settings or Email Alert page requires Administrator password. The
default password is "0000".
46
3. This page allows you to make adjustments to the AMX and SNMP settings. In the
AMX device discover row, when ON is selected, the projector can be detected by
controllers of AMX connected to the same network. For the Details of AMX Device
Discovery, visit the AMX web site at http://www.amx.com/.
4. If your projector is connected to a network which supports Simple Mail Transfer
Protocol (SMTP), you can configure it to alert you via email on significant events.
5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See
"About Crestron e-Control®" on page 47 for details.
Please pay attention to the limitation of input length (including space and other
punctuation keys) in the list blow:
Category Item Input-Length Maximum Number of Characters
Network Settings
Network
DHCP/Manual (N/A)
IP Address XXX.XXX.XXX.XXX
Subnet Mask XXX.XXX.XXX.XXX
Gateway XXX.XXX.XXX.XXX
DNS Server XXX.XXX.XXX.XXX
AMX device discovery (N/A)
Password
Administrator (N/A)
New Password 4
Confirm Password 4
SNMP
SysLocation 22
SysName 22
SysContact 22
47
• / > < $ % + \ ' " are prohibited.
About Crestron e-Control®
1. The Crestron e-Control® page provides a variety of virtual keys to control the
projector or adjust the projected pictures.
i. These buttons function the same as the ones on the OSD menus or remote
control.
ii. To switch input source, click on your desired signal.
Important
• The Menu button can also be used to go back to previous OSD menu, exit and save
menu settings.
• The source list varies according to the connectors available on the projector.
• When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
2. The tools page allows you to manage the projector, configure the Lan control
settings and secure access of remote network operation on this projector.
Email Alert
Email Setting
To 4 0
Cc 40
Subject 15
From 40
SMTP Setting
Server 30
User Name 40
Password 14
Alert Condition
Fan Error (N/A)
Lamp Error (N/A)
Temperature Error (N/A)
Submit (N/A)
Issue Test Mail (N/A)
i
i
i
ii
You can
press / to
reveal more
buttons.
48
i. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge
of it.
iii. You can adjust the Lan control setting.
iv. Once set, access to the remote network operation on this projector has been
password-protected.
v. Once set, access to the tools page has been password-protected.
• To prevent errors, only input the English alphabet and digits on the tools page.
• After making the adjustments, press the Send button and the data will be saved in the projec-
tor.
vi.Press exit to go back to the Crestron remote network operation page.
Please pay attention to the limitation of input length (including space and other
punctuation keys) in the list blow:
Category Item Input-Length Maximum Number of Characters
Crestron Control
IP Address 15
IP ID 2
Port 5
Projector
Projector Name 10
Location 9
Assigned To 9
Network Configuration
DHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password
Enabled (N/A)
New Password 20
Confirm 2
Admin Password
Enabled (N/A)
New Password 20
Confirm 20
iv
iii v
vi
ii
i
49
3. The info page displays the information and status of this projector.
i. Press exit to go back to the Crestron remote network operation page.
4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in
the upper right corner of the screen. You will be able to deliver messages to
RoomView™ software administrators/users who connect to the same local area
network.
• For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the
projector’s on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved
Crestron control port.
About Crestron RoomView™ setting and command method, please access below
website to get RoomView™ User Guide and more information: http://
www.crestron.com/products/roomview_connected_embedded_projectors_devices/
resources.asp
i
50
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not
turned on). To use these functions, be sure you have turned on the corresponding
menus under SOURCE > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the "Connection" on page 14 chapter.
Active VGA out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER
OUT sockets are correctly connected to devices. The projector outputs the signal
received only from COMPUTER IN 1.
Active Audio out
Selecting On outputs an audio signal when the AUDIO IN 1 socket is correctly
connected to a proper device.
LAN Control
Selecting On allows the projector to provide the network function when it is in standby
mode. See "Controlling the projector through a LAN environment" on page 44 for
details.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker.
Be sure you have made a correct connection to the projector audio input/output jacks.
See "Connection" on page 14 for more details.
Adjusting the audio mode
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio
Settings > Audio Mode menu.
2. Press / to select a preferred audio mode.
• If available, you can press Audio Mode on the remote control to select a preferred audio
mode.
Muting the sound
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio
Settings > Mute menu.
2. Press / to select On.
• If available, you can press on the remote control to toggle the projector audio between on
and off.
Adjusting the sound level
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio
Settings > Audio Volume menu.
51
2. Press / to select a desired sound level.
• If available, you can press / on the remote control to adjust the projector’s sound
level.
Adjusting the Audio In 2 setting
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio
Settings > Audio In 2 menu.
2. Press / to decide the audio input source for the AUDIO IN 2/MIC port. This
will affect the connection method for different devices, and where the sound is
from.
• When Audio is selected:
• The selected input signal determines which sound will be played by the projector speaker,
and which sound will be output from the projector when AUDIO OUT is connected. For
instance, if you select a D-Sub / Comp. 1 source, the projector can play the sound received
from AUDIO IN 1.
• When Microphone is selected:
Adjusting the microphone sound level
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio
Settings > Microphone Volume menu.
2. Press / to select a desired sound level.
• This function is only available when the SYSTEM SETTING: ADVANCED > Audio Settings >
Audio In 2 menu is set to Microphone.
Turning off the Power On/Off Ring Tone
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio
Settings > Power On/Off Ring Tone menu.
2. Press / to select Off.
• The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.
Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video
Audio input port AUDIO IN 1 AUDIO IN 2 AUDIO IN 2
The projector can play
the sound from... AUDIO IN 1 AUDIO IN 2 AUDIO IN 2
Audio output port AUDIO OUT AUDIO OUT AUDIO OUT
Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video
The projector can play
the sound from... MIC MIC MIC
Audio output port AUDIO OUT AUDIO OUT AUDIO OUT
52
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
• Never open any of the covers on the projector. Dangerous electrical voltages inside the
projector can cause severe injury. Do not attempt to service this product yourself. Refer
all servicing to qualified service personnel.
Cleaning the lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the projector housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Note
• Turn off the projector and remove the AC power cord from the power outlet before
beginning maintenance work.
• Make sure the lens is cool before cleaning.
• Do not use detergents or chemicals other than those noted above. Do not use benzene
or thinners.
• Do not use chemical sprays.
• Use a soft cloth or lens paper only.
53
Installing the dust filter (optional accessory)
Caution
• It is important to clean the dust filter every 100 hours after the dust filter is installed.
• Be sure to turn off the projector and unplug it from power source before installing or
detaching the filter.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to
your personal safety when replacing the dust filter.
Installing the dust filter
1. Be sure to turn off the projector and unplug it from power source.
2. As the arrows shown to the right, fit the filter by
aligning and inserting it into the projector slots.
Make sure it clicks into place.
For first time installation:
3. Open the OSD menu and go to the SYSTEM
SETTING: ADVANCED > Filter Settings menu.
4. Press Enter and the Filter Settings page is
displayed.
5. Highlight Filter Mode and select "On". The filter timer starts counting and the
projector will remind you to clean the filter when the filter is in use for over 100
hours.
Caution
• Set Filter Mode to On only when using the projector after the dust filter (optional
accessory) is properly attached. Failing to do so will result in a shorter lamp life.
Obtaining the filter hour information
1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter
Settings menu.
2. Press Enter and the Filter Settings page is displayed.
3. You will see the Filter Hours information on the menu.
Cleaning the dust filter
1. Be sure to turn off the projector and unplug it from power source.
2. Press the latches on the dust filter and remove the filter from the projector.
3. Use a small vacuum cleaner or a soft brush to sweep the dust on the filter away.
4. Re-install the dust filter.
54
Resetting the filter timer
5. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter
Settings menu.
6. Press Enter and the Filter Settings page is displayed.
7. Highlight Reset Filter Hours and press Enter. A warning message is displayed
asking if you want to reset the filter timer.
8. Highlight Reset and press Enter. The lamp timer will be reset to '0'.
Caution
• Remember to use Filter Mode to Off in the SYSTEM SETTING: ADVANCED > Filter
Settings menu when using the projector with the dust filter removed. Setting Filter Mode
to Off does not reset the filter timer. The timer will continue counting the next time you
fit the filter back on and set Filter Mode to On.
Installing the cable management cover (optional
accessory)
1. Make sure that all the cables are properly connected to the projector.
2. Attach the cable management cover to the back of the projector.
3. Tighten the screws that secure the cable management cover.
55
Replacing the lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
Note
• The lamp is extremely hot right after turning off the projector. If you touch the lamp, you
may scald your finger. When you replace the lamp, wait for at least 45 minutes for the
lamp to cool down.
• Do not touch the lamp glass at any time. The lamp may explode due to improper
handling, including the touching of the lamp glass.
• Lamp lifetime may differ from lamp to lamp and according to the environment of use.
There is no guarantee of the same lifetime for each lamp. Some lamps may fail or
terminate their lifetime in a shorter period of time than other similar lamps.
• A lamp may explode as a result of vibration, shock or degradation as a result of hours of
use as its lifetime draws to an end. Risk of explosion may differ according to the
environment or conditions in which the projector and lamp are being used.
• Wear protective gloves and eyeglasses when fixing or detaching the lamp.
• Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least for 5
minutes to turn off the projector after powering on.
• Do not operate the lamp in proximity to paper, cloth, or other combustible material nor
cover it with such materials.
• Do not operate the lamp in an atmosphere containing an inflammable substance, such
as thinner.
• Thoroughly ventilate the area or the room when operating the lamp in an oxygen
atmosphere (in the air). If ozone is inhaled, it could cause headaches, nausea, dizziness,
and other symptoms.
• The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury inside the
lamp will be exposed. Leave the area immediately if the lamp shatters while being
operated and ventilate the area for at least 30 minutes in order to avoid the inhalation of
mercury fumes. Otherwise it could be harmful to user’s health.
56
1. Turn off the projector.
2. If the projector is installed in a ceiling mount, remove it.
3. Unplug the power cord.
4. Loosen the screw in the side of the lamp cover.1
5. Remove the cover.2
6. Loosen the screws from the lamp module.3
7. Raise the handle and pull out the lamp module slowly and carefully.4
8. Insert the new lamp module into the projector and tighten the screws.
9. Replace the lamp cover and tighten the screw.
10.Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
11. Reset the lamp hour. Refer to the “SYSTEM SETTING: ADVANCED > Lamp
Settings > Reset Lamp Hours” menu.
Note
• Dispose the used lamp according to local regulations.
• Ensure that screws are tightened properly. Screws not tightened fully may result in
injury or accidents.
• Since the lamp is made of glass, do not drop the unit and do not scratch the glass.
• Do not reuse the old lamp. This could cause the lamp to explode.
• Be sure to turn off the projector and unplug the AC power cord before replacing the
lamp.
• Do not use the projector with the lamp cover removed.
1
3
4
2
57
Specifications
Model name PJD6250L PJD6252L PJD7325 PJD6550W PJD6552W PJD7525W
Dislay system Single 0.55" DLP panel Single 0.65" DLP panel
Resolution XGA (1024 x 768 pixels) WXGA (1280 x 800 pixels)
Zoom 1.1x 1.2x
F/No. 2.5 - 2.7 2.56
Focal length 22.08 - 24.28mm 20.99 - 25.61mm
Screen size 30” - 300”
Lamp 203W 220W 250W 203W 220W 250W
Input terminal D-Sub 15-pin x 2, HDMI x 1, S-Video x 1, Video x 1, Audio signal input (3.5
mm stereo mini jack) x 1, Audio signal input/Microphone input x 1
Output terminal D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini jack) x 1, USB type
A port for power charging (5V/2A)
Control terminal RS-232 x 1, Mini-B USB x1 (supports firmware upgrade and remote mouse
control), RJ45 x 1
Speaker 16 watt x 1
Video compatibility
NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency
31 - 100 KHz
24 - 120 Hz
Environment
Operating:
Temperature: 0°C to 40°C
Humidity: 10%-90%
Storage:
Temperature: -20°C to 60°C
Humidity:10%-90%
Power requirement AC 100-240 V, 50 - 60 Hz, 5.2A
Power consumption 265W
(Max.)
275W
(Max.)
315W
(Max.)
265W
(Max.)
275W
(Max.)
315W
(Max.)
Dimension
(W x D x H) 362 x 231 x 109 mm
Weight 2. 7 kg (6.0 lb) without cable management cover
Note: Design and Specifications are subject to change without prior notice.
58
Dimensions
362 mm (W) x 231 mm (D) x 109 mm (H)
Ceiling mount installation
231
362
109
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
65.89
113.54 60.01
59
Appendix
LED indicator messages
LED Type Color Status Meaning
Power LED Blue Solid
Normal power of standby mode .Temp LED Red Off
Lamp LED Red Off
Power LED Blue Flash
Low power of standby mode. Temp LED Red Off
Lamp LED Red Off
Power LED Blue Flash
Powering upTemp LED Red Off
Lamp LED Red Off
Power LED Blue Solid
Normal operationTemp LED Red Off
Lamp LED Red Off
Power LED Blue Solid
Powering downTemp LED Red Off
Lamp LED Red Off
Power LED Blue Solid If the projector system has some problems
with its fans, the projector will shut down.
Temp LED Red Flash
Lamp LED Red Flash
Power LED Blue Solid The lamp has reached its end of life and
must be changed soon. The lamp will
continue to operate until it fails. Change the
lamp. If the lamp is off, then the ballast will
become malfunction.
Temp LED Red Off
Lamp LED Red Flash
Power LED Blue Flash 1. Temperature is too high. The lamp will
turn off. The fan motor is cooling the lamp.
Or
2. The cooling process is not complete after
the projector is shut down and re-started
right away.
Temp LED Red Flash
Lamp LED Red Off
Power LED Blue Flash The lamp ignition failed. If temperature is
too high, the fans will cool the lamp.
Temp LED Red Off
Lamp LED Red Solid
Power LED Blue Solid
Color wheel start failTemp LED Red Solid
Lamp LED Red Solid
60
Compatibility modes
Supported 3D signal for PC input
• The timings showing above may not be supported due to EDID file and VGA
graphic card limitations. It is possible that some timings cannot be chosen.
• 120Hz is signals are supported for frame sequential format only.
Resolution
Horizontal
frequency
(KHz)
Vertical
frequency
(Hz)
Pixel
Frequency
(MHz)
3D frame
sequential
3D top
bottom
3D side
by side
640 x 480
59.94 31.469 25.175 ◎◎◎
72.809 37.861 31.500
75 37.5 31.500
85.008 43.269 36.000
720 x 400 70.087 31.469 28.3221
800 x 600
60.317 37.879 40.000 ◎◎◎
72.188 48.077 50.000
75 46.875 49.500
85.061 53.674 56.250
119.854 77.425 83.000 ◎
1024 x 768
60.004 48.363 65.000 ◎◎◎
70.069 56.476 75.000
75.029 60.023 78.750
84.997 68.667 94.500
119.989 97.551 115.5 ◎
1152 x 864 75 67.5 108
1280 x 720 60 45 74.250 ◎◎◎
120 90.000 148.500 ◎
1280 x 768 59.87 47.776 79.5 ◎◎◎
1280 x 800
59.81 49.702 83.500 ◎◎◎
74.934 62.795 106.500
84.88 71.554 122.500
119.909 101.563 146.25 ◎
1280 x 1024
60.02 63.981 108.000 ◎◎
75.025 79.976 135.000
85.024 91.146 157.500
1280 x 960 60 60 108.000 ◎◎
85.002 85.938 148.500
1360 x 768 60.015 47.712 85.5 ◎◎
1440 x 900 59.887 55.935 106.500 ◎◎
1400 x 1050 59.978 65.317 121.750 ◎◎
1600 x 1200 60 75 162.000 ◎◎
1680 x 1050 59.954 65.29 146.25 ◎◎
1920 x 1200 59.95 74.038 154.000 ◎◎
640 x 480
@67Hz 66.667 35 30.240
832 x 624
@75Hz 74.546 49.722 57.280
1024 x 768
@75Hz 75.02 60.241 80.000
1152 x 870
@75Hz 75.06 68.68 100.000
61
Supported timing for Component-YPbPr input
• *Supported timing for 3D signal with Frame Sequential format.
• Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight
image vibration.
Timing Resolution Vertical
Frequency (Hz)
Horizontal
Frequency
(kHz)
Pixel
Frequency
(MHz)
480i* 720 x 480 59.94 15.73 13.5
480p* 720 x 480 59.94 31.47 27
576i 720 x 576 50 15.63 13.5
576p 720 x 576 50 31.25 27
720/50p 1280 x 720 50 37.5 74.25
720/60p* 1280 x 720 60 45.00 74.25
1080/50i 1920 x 1080 50 28.13 74.25
1080/60i 1920 x 1080 60 33.75 74.25
1080/24P 1920 x 1080 24 27 74.25
1080/25P 1920 x 1080 25 28.13 74.25
1080/30P 1920 x 1080 30 33.75 74.25
1080/50P 1920 x 1080 50 56.25 148.5
1080/60P 1920 x 1080 60 67.5 148.5
62
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
•
Be sure that the power cord is securely connected to the projector and the other end
is
plugged into an outlet with power.
• Press the power button again.
•
Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
•
Press
Source
to select an active input source.
• Be sure the external source is turned on and connected.
•
For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
•
While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
• Check the projection lens to see if it needs cleaning.
• If the image is flickering or unstable for a computer connection:
• Press
Menu
, go to DISPLAY and adjust Phase or H. Size.
Remote control problems
If the remote control does not operate:
• Be sure nothing is blocking the remote control receiver on the front of the projector.
Use the remote control within the effective range.
• Aim the remote control at the screen or at the front of the projector.
•
Move the remote control so it is more directly in front of the projector and
not as far to
the side.
63
RS-232 command and configuration
D-Sub 9 pin
11 CD
2RXD
3TXD
4DTR
5GND
6DSR
7RTS
8CTS
9RI
Baud Rate 115200 bps
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
Wire List
C1 COLOR C2
1 Black 1
2Brown 3
3Red 2
4 Orange 6
5 Yellow 5
6Green 4
7Blue 8
8Purple 7
9White 9
SHELL DW SHELL
64
Function Status Action cmd
Power
Write Power on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Power off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Read Power status (on/off) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00
0x5E
Reset all settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Reset Color
Settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87
Splash Screen
Write
Splash Screen Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash Screen Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Splash Screen
ViewSonic 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Splash Screen
Screen Capture 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x03 0x6A
Splash Screen Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Read Splash Screen status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A
0x68
Quick Power Off
Write Quick Power Off Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
Quick Power Off On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Read Quick Power Off
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B
0x69
High Altitude Mode
Write
High Altitude Mode
Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High Altitude Mode
On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
Read High Altitude Mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C
0x6A
Lamp Mode
Write
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Economic 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Dynamic 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x02 0x6F
Sleep Mode 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x03 0x70
Read Lamp Mode status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10
0x6E
Message
Write Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27
0x85
Projector Position
Write
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Read Projector position
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00
0x5F
3D Sync
Write
OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
Frame Sequential 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80
Frame Packing 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81
Top-Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82
Side-by-Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83
Read 3D Sync Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20
0x7F
3D Sync Invert
Write Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
Read 3D Sync Invert
Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21
0x80
65
Contrast
Write Contrast decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Read Contrast ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02
0x61
Brightness
Write Brightness decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Read Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03
0x62
Aspect ratio
Write
Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Aspect ratio
Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68
Aspect ratio Wide 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68
Read Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04
0x63
Auto Adjust Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Horizontal position
Write
Horizontal position
shift right 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Horizontal position
shift left 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Read Horizontal position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06
0x65
Vertical position
Write
Vertical position shift
up 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Vertical position shift
down 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
Read read Vertical position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07
0x66
Color temperature
Write
color temperature
Warm 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
color temperature
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
color temperature
Neutral 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
color temperature
Cool 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
Read color temperature
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08
0x67
Blank
Write Blank On 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank Off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09
0x68
Keystone-
Vertical
Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E
Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F
Read Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31
0x8F
Keystone-
Horizontal
Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E
Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F
Read Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31
0x8F
Color mode
Write
Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
PC 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
ViewMatch 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Dynamic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x08 0x71
Read Preset mode status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B
0x6A
66
Primary Color
Write
Primary color R 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Primary color G 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Primary color B 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Primary color C 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Primary color M 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Primary color Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Read Primary color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10
0x6F
Hue
Write Hue decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Hue increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Read Hue 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11
0x70
Saturation
Write Saturation decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Saturation increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Read Saturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12
0x71
Gain
Write Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13
0x72
Freeze
Write Freeze On 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze Off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00
0x60
Source input
Write
Input source VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Input source VGA2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
Input source HDMI 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Input source HDMI2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67
Input source
Composite 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Input source SVIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Read Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01
0x61
Quick Auto Search
Write
Quick Auto Search
on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto Search
off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Read Quick Auto Search
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02
0x62
Mute
Write Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Read Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00
0x61
Volume
Write Increse Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Decrese Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03
0x64
67
Language
Write
English 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
Deutsch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
Italiano 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
Svenska 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
Nederlands 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
Polski 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
Suomi 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73
Indonesia 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75
Read Language 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00
0x62
Lamp Time
Write Reset Lamp usuage
hour 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Read Lamp usuage hour 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01
0x63
HDMI Format
Write
RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85
YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87
Read HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28
0x86
HDMI Range
Write
Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86
Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87
Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88
Read HDMI Range status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29
0x87
CEC
Write Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88
On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89
Read CEC status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B
0x89
Error status Read Read error status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D
0x66
Brilliant Color
Write
Brilliant Color 0 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D
Brilliant Color 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E
Brilliant Color 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x02 0x6F
Brilliant Color 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x03 0x70
Brilliant Color 4 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x04 0x71
Brilliant Color 5 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x05 0x72
Brilliant Color 6 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x06 0x73
Brilliant Color 7 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x07 0x74
Brilliant Color 8 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x08 0x75
Brilliant Color 9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x09 0x76
Brilliant Color 10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x0A 0x77
Read Brilliant Color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0F
0x6E
68
Remote Control
code
Write
code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0
code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1
code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2
code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3
code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4
code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5
code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6
code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7
Read Remote Control code
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x048
0xA1
Screen Color
Write
Screen color Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x00 0x8F
Blackboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x01 0x90
Greenboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x02 0x91
Whiteboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x03 0x92
Read Screen Color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x32
0x90
Over Scan
Write
Overscan Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x00 0x90
Overscan 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x01 0x91
Overscan 2 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x02 0x92
Overscan 3 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x03 0x93
Overscan 4 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x04 0x94
Overscan 5 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x05 0x95
Read Overscan status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x33
0x91
Remote Key Write
Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61
Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65
Top 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D
Bottom 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E
Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F
Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60
Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56
Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67
Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x08 0x5A
My Button 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x11 0x63
69
IR control table
System Code: 83F4
Format : NEC
70
Address code
Key Format Byte1 Byte2 Byte3 Byte4
Freeze NEC X3 F4 03 FC
PgDn NEC X3 F4 05 FA
PgUp NEC X3 F4 06 F9
Blank NEC X3 F4 07 F8
Auto sync NEC X3 F4 08 F7
Up NEC X3 F4 0B F4
Down NEC X3 F4 0C F3
Left NEC X3 F4 0E F1
Right NEC X3 F4 0F F0
Color Mode NEC X3 F4 10 EF
Aspect NEC X3 F4 13 EC
Mute NEC X3 F4 14 EB
Enter NEC X3 F4 15 EA
Power ON NEC X3 F4 17 E8
Magnify NEC X3 F4 32 CD
Presentation Timer NEC X3 F4 27 D8
Exit NEC X3 F4 28 D7
D. ECO
(Eco mode) NEC X3 F4 2B D4
Menu NEC X3 F4 30 CF
Mouse NEC X3 F4 31 CE
Mouse Left NEC X3 F4 36 C9
Mouse Right NEC X3 F4 37 C8
Source NEC X3 F4 40 BF
VGA (PC) NEC X3 F4 41 BE
Pattern NEC X3 F4 55 AA
My button NEC X3 F4 56 A9
HDMI NEC X3 F4 58 A7
Volume+ NEC X3 F4 82 7D
Volume- NEC X3 F4 83 7C
Key pad lock NEC X3 F4 8E 71
RC ID NEC X3 F4 96 69
Code 1 83F4
Code 2 93F4
Code 3 A3F4
Code 4 B3F4
Code 5 C3F4
Code 6 D3F4
Code 7 E3F4
Code 8 F3F4
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/Region Website T= Telephone
C = CHAT ONLINE Email
Australia
New Zealand www.viewsonic.com.au AUS= 1800 880 818
NZ= 0800 008 822 service@au.viewsonic.com
Canada www.viewsonic.com T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533 service.ca@viewsonic.com
Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com
India www.in.viewsonic.com T= 1800 419 0959 service@in.viewsonic.com
Korea ap.viewsonic.com/kr/ T= 080 333 2131 service@kr.viewsonic.com
Latin America
(Argentina) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Chile) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Columbia) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Mexico) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.
Tel: 55) 6547-6454 55)6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico
Latin America
(Peru) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com
Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com
Puerto Rico &
Virgin Islands www.viewsonic.com
T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/
la/soporte/servicio-tecnico
service.us@viewsonic.com
soporte@viewsonic.com
Singapore/
Malaysia/Thailand www.ap.viewsonic.com T= 65 6461 6044 service@sg.viewsonic.com
South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com
United States www.viewsonic.com T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530 service.us@viewsonic.com
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South America: Three
(3) years warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the
original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours average
daily usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1)
year for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase;
Europe: One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90)
days for the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper
maintenance, unauthorized product modification, or failure to follow instructions supplied with
the product.
b. Operation outside of product specifications.
c. Operation of the product for other than the normal intended use or not under normal
conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power fluctuations or failure.
h. Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, one way transportation, insurance, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(Please refer to Customer Support page). You will need to provide your product's serial number.
2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic
service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact
ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
inconvenience, loss of use of the product, loss of time, loss of profits, loss of business
opportunity, loss of goodwill, interference with business relationships, or other commercial loss,
even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion
of incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in www.
viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during
the warranty period. If a product proves to be defective in material or workmanship during the warranty period,
ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts
may include remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first
consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed
lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, unauthorized attempted repair, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic's specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as "image burn-in" which results when a static image is
displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product's serial number, so please record the
product information in the space provided below on your purchase for your future use. Please retain your receipt
of proof of purchase to support your warranty claim.
For Your Records
Product Name: _____________________________ Model Number: _________________________________
Document Number: _________________________ Serial Number: _________________________________
Purchase Date: _____________________________ Extended Warranty Purchase? _________________ (Y/N)
If so, what date does warranty expire? _______________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic's liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss
of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference
with business relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
