Table of Contents
- Safety Precautions - General
- Initial Setup
- Making Connections
- Operation
- Menu Functions
- Appendix
- Regulatory and Service Information
Viewsonic PX727HD User Manual
Displayed below is the user manual for PX727HD by Viewsonic which is a product in the Data Projectors category. This manual has pages.
Related Manuals
Model No. VS17694
Model Name: PX727HD
IMPORTANT: Please read this User Guide to obtain important informaon on installing and using your product
in a safe manner, as well as registering your product for future service. Warranty informaon contained in this
User Guide will describe your limited coverage from ViewSonic Corporaon, which is also found on our web site at
hp://www.viewsonic.com in English, or in specic languages using the Regional selecon box in the upper right
corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”
As a world-leading provider of visual soluons, ViewSonic® is dedicated to exceeding the
world’s expectaons for technological evoluon, innovaon, and simplicity. At ViewSonic®,
we believe that our products have the potenal to make a posive impact in the world, and
we are condent that the ViewSonic® product you have chosen will serve you well.
Once again, thank you for choosing ViewSonic®!
Please read the following before you start using the projector.
• Keep this user guide in a safe place for later reference.
• Read all warnings and follow all instructions.
• Allow at least 20“ (50 cm) clearance around the projector to ensure proper
ventilation.
• Place the projector in a well-ventilated area. Do not place anything on the
projector that prevents heat dissipation.
• Do not place the projector on an uneven or unstable surface. The projector may
fall over, causing personal injury or projector malfunction.
• Do not use if the projector is tilted at an angle of more than 10° degrees left or
right, nor at an angle of more than 15° degrees forwards or backwards.
• Do not look straight at the projector lens during operation. The intense light
beam may damage your eyes.
• Always open the lens shutter or remove the lens cap when the projector lamp is
on.
• Do not block the projection lens with any objects when the projector is under
operation as this could cause objects to become heated and deformed or even
cause a fire.
• The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
• Do not use lamps beyond the rated lamp life. Excessive use of lamps beyond the
rated life could cause them to break on rare occasions.
• Never replace the lamp assembly or any electronic component unless the
projector is unplugged.
• Do not attempt to disassemble the projector. There are dangerous high voltages
inside which may cause death if you should come into contact with live parts.
• When moving the projector, be careful not to drop or bump the projector on
anything.
• Do not place any heavy objects on the projector or connection cables.
• Do not stand the projector on end vertically. Doing so may cause the projector
to fall over, causing personal injury or projector malfunction.
• Avoid exposing the projector to direct sunlight or other sources of sustained
heat. Do not install near any heat sources such as radiators, heat registers,
stoves, or other devices (including amplifiers) that may increase the
temperature of the projector to dangerous levels.
• Do not place liquids near or on the projector. Liquids spilled into the projector
may cause it to fail. If the projector does become wet, disconnect it from the
power supply and call your local service center to have the projector serviced.
• When the projector is under operation, you may sense some heated air and
odor from its ventilation grill. It is a normal operation and not a defect.
• Do not attempt to circumvent the safety provisions of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding prong. The
wide and third blade are provided for your safety. If the plug does not fit into
your outlet, obtain an adapter and do not attempt to force the plug into the
outlet.
• When connecting to a power outlet, DO NOT remove the grounding prong.
Please ensure grounding prongs are NEVER REMOVED.
• Protect the power cord from being treaded upon or pinched, particularly at the
plug, and at the point where it emerges from the projector.
• In some countries, the voltage is NOT stable. This projector is designed to
operate safely within a voltage between 100 to 240 volts AC, but could fail if
power cuts or surges of ±10 volts occur. In areas where voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector, or uninterruptable power supply (UPS).
• If smoke, an abnormal noise, or a strange odor is present, immediately switch
the projector off and call your dealer or ViewSonic®. It is dangerous to continue
using the projector.
• Use only attachments/accessories specified by the manufacturer.
• Disconnect the power cord from the AC outlet if the projector is not being used
for a long period of time.
• Refer all servicing to qualified service personnel.
Possibly hazardous optical radiation is emitted from this product. As
with any bright light source, do not stare into the beam,
RG2 IEC 62471-5:2015.
Please read the following before you start using the projector.
If you intend to mount the projector on the ceiling, we strongly recommend
that you use a proper fitting projector ceiling mount kit and that you ensure it is
securely and safely installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use
of the wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your
projector. We recommend that you also purchase a separate security cable and
attach it securely to both the anti-theft lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the
projector should its attachment to the mounting bracket become loose.
Features ................................................................................................................10
Package Contents .................................................................................................10
Product Overview .................................................................................................11
Projector ................................................................................................................ 11
Controls and Functions ............................................................................................... 11
Connection Ports ......................................................................................................... 12
Remote Control ..................................................................................................... 13
Controls and Functions ............................................................................................... 13
Remote Control Effective Range ................................................................................. 14
Replacing the Remote Control Batteries ..................................................................... 14
Choosing a Location ..............................................................................................15
Projection Dimensions ..........................................................................................16
16:9 Image on a 16:9 Screen ....................................................................................... 16
16:9 Image on a 4:3 Screen ......................................................................................... 17
Mounting the Projector ........................................................................................18
Preventing Unauthorized Use...............................................................................19
Using the Security Slot .......................................................................................... 19
Using the Password Function ................................................................................ 20
Setting a Password ...................................................................................................... 20
Changing the Password ............................................................................................... 21
Disabling the Password Function ................................................................................ 21
Forgetting the Password ............................................................................................. 22
Password Recall Procedure ......................................................................................... 22
Locking the Control Keys ....................................................................................... 23
Connecting to Power ............................................................................................24
Connecting to Video Sources ................................................................................25
HDMI Connection .................................................................................................. 25
Connecting to Computer Sources .........................................................................26
VGA Connection .................................................................................................... 26
VGA Out Connection ............................................................................................. 26
Connecting to Audio .............................................................................................27
Turning the Projector On/Off ...............................................................................28
Starting Up the Projector ...................................................................................... 28
First Time Activation ................................................................................................... 28
Shutting Down the Projector ................................................................................. 29
Selecting an Input Source .....................................................................................30
Adjusting the Projected Image .............................................................................31
Adjusting the Projector's Height and Projection Angle ............................................... 31
Auto-Adjusting the Image ........................................................................................... 31
Fine-Tuning the Image Size and Clarity ................................................................. 31
Correcting Keystone .............................................................................................. 32
Adjusting 4 corners ............................................................................................... 33
Hiding the Image ..................................................................................................33
General On-Screen Display (OSD) Menu Operation .............................................34
On-Screen Display (OSD) Menu Tree ....................................................................35
DISPLAY Menu ......................................................................................................41
IMAGE Menu ........................................................................................................44
POWER MANAGEMENT Menu .............................................................................48
BASIC Menu ..........................................................................................................51
ADVANCED Menu .................................................................................................54
SYSTEM Menu .......................................................................................................57
INFORMATION Menu ...........................................................................................60
Specifications ........................................................................................................61
Projector Dimensions ............................................................................................ 62
Timing Chart .........................................................................................................62
Analog RGB ............................................................................................................ 62
HDMI (PC) .............................................................................................................. 64
HDMI (Video) ......................................................................................................... 65
IR Control Table ....................................................................................................66
Address Code ........................................................................................................67
RS-232 Command Table .......................................................................................68
Pin Assignment ...................................................................................................... 68
Interface ................................................................................................................ 68
Command Table .................................................................................................... 68
Glossary ................................................................................................................75
Troubleshooting ...................................................................................................78
Common Problems ................................................................................................ 78
LED Indicators ........................................................................................................ 79
Maintenance.........................................................................................................80
General Precautions .............................................................................................. 80
Cleaning the Lens .................................................................................................. 80
Cleaning the Case .................................................................................................. 80
Storing the Projector ............................................................................................. 80
Disclaimer .............................................................................................................. 80
Lamp Information .................................................................................................81
Lamp Hour ............................................................................................................. 81
Extending Lamp Life .............................................................................................. 81
Lamp Replacement Timing .................................................................................... 82
Replacing the Lamp ............................................................................................... 82
Compliance Information .......................................................................................83
FCC Compliance Statement ................................................................................... 83
Industry Canada Statement ................................................................................... 83
CE Conformity for European Countries ................................................................. 83
Declaration of RoHS2 Compliance......................................................................... 84
Indian Restriction of Hazardous Substances ......................................................... 85
Product Disposal at End of Product Life ................................................................ 85
Copyright Information ..........................................................................................86
Customer Service .................................................................................................. 87
Limited Warranty .................................................................................................. 88
Mexico Limited Warranty ...................................................................................... 91
PX727HD is a practical Home Cinema Projector, featuring 2000 ANSI lumens and
1080p Full HD resolution to produce the finest of details in any medium sized space.
Also includes ViewSonic’s exclusive Cinema SuperColor ™ technology which provides
users with a stunning color performance.
• Amazing 20,000 hours lamp life.
• Power saving funcon that decreases the lamp power consumpon by up to 60%
when no input signal is detected for a set me period.
• Firmware updates via USB Type A.
• USB Type A port can provide streaming with an HDMI wireless dongle and supply
power.
• 7 color modes for dierent projecon purposes.
• Embedded ISF Mode delivers opmized color in both bright and dark environments.
• Rec.709 ensures all equipment is speaking the same color language.
• The 6X Speed RGB color wheel opmizes Rec.709 color by boosng reds, blues,
and greens.
• Cinema SuperColor enhances viewing experience with movie color schemes.
• 3D display supported.
• Less than 0.5W power consumpon when power saving mode is turned on.
• Quick Auto Search, thus speeding up the signal detecng process.
• One-key auto-adjustment for displaying the best picture quality (only for analog
signal).
• Digital keystone correcon and/or 4 corner adjustment to correct distorted images.
• Ability to display 1.07 billion colors.
• Mul-language On-Screen Display (OSD) menus.
• HDMI CEC (Consumer Electronics Control) funcon allowing synchronized power
ON/OFF operaon between the projector and a CEC-compable DVD player
device connected to the HDMI input of the projector.
• Projector
• Power Cord
• Video Cable
• Remote Control & Baeries
• Quick Start Guide
The power cord and video cables included in your package may vary depending
on your country. Please contact your local reseller for more informaon.
EXIT
MENU
SOURCE
BLANK
MODE
COLOR
Power Indicator
Light
Temperature Indicator Light
Lamp Indicator Light
Focus Ring
Zoom Ring
Projection Lens
Vent (heated air
exhaust)
Remote IR sensor
[ ] Power Toggles the projector between standby mode and Power On.
[ / / / ] Keystone
Keys
Manually corrects distorted images resulting from an angled
projection.
[ / / / ]
Left/Right/Up/Down
Selects the desired menu items and makes adjustments
when the On-Screen Display (OSD) Menu is activated.
Menu/Exit Turns on or off the On-Screen Display (OSD) Menu.
Source Displays the input source selection bar.
Blank Hides the screen picture.
Enter Enacts the selected On-Screen Display (OSD) Menu item
when the OSD Menu is activated.
[ ] Corner Adjustment Displays the Corner Adj. menu.
[ ] Volume Up Increases the volume level.
[ ] Volume Down Decreases the volume level.
Color Mode Displays the color mode selection bar.
1 2 3 4 5 6 7 8
AC Power Cord Inlet
Ceiling Mount Holes
Security Slot
Security Bar
Adjuster Foot
[1] AUDIO OUT Audio signal output socket.
[2] AUDIO IN Audio signal input socket.
[3] HDMI 1 HDMI port.
[4] HDMI 2 HDMI port.
[5] USB 5V/1.5A OUT
(Service)
USB Type A port for power supply.
[6] COMPUTER IN RGB (PC) signal input socket.
[7] MONITOR OUT RGB (PC) signal output socket.
[8] RS-232 RS-232 control port.
On Off
HDMI 1 HDMI 2COMP
Source
Pattern
Brightness
Contrast
Aspect
Color
Temp
Eco
Mode
StandardGaming Sports
Movie User
Blank 3D
Auto
Sync
ID Set 1 2
3 4 5
6 7 8
On/ Off Toggles between standby
mode and Power On.
COMP Selects the source from
the port for
display.
HDMI 1 Selects the source from the
port for display.
HDMI 2 Selects the source from the
port for display.
Auto Sync Automatically determines
the best picture timings for
the displayed image.
Source Displays the source
selection bar.
[ / / / ]
Keystone Keys
Manually corrects distorted
images resulting from an
angled projection.
Enter Enacts the selected OSD
Menu item.
(Corner
Adjustment)
Displays the Corner Adj.
menu.
Left/ Right
Up/ Down
Selects the desired
menu items and makes
adjustments.
Menu Turns on/off the On-Screen
Display (OSD) Menu or
goes back to previous OSD
Menu.
(INFORMATION)
Displays the
menu.
Exit Exits and saves menu
settings.
Aspect Displays the aspect ratio
selection bar.
Pattern Displays embedded test
pattern.
Blank Hides the screen picture.
3D Displays the 3D menu.
(Volume Up) Increases the volume level.
(Volume
Down)
Decreases the volume
level.
(Mute) Toggles audio between on
and off.
Brightness Displays the brightness
adjustment bar.
Contrast Displays the contrast
adjustment bar.
Color Temp Displays the color
temperature selection
menu.
Gaming Selects the mode.
Standard Selects the
mode.
Sports Selects the mode.
Eco Mode Selects the mode.
Movie Selects the
mode.
User Selects the or
mode.
To ensure proper function of the remote control
follow the steps below:
The remote control must be held at an angle
within 30° perpendicular to the projector’s IR
remote control sensor(s).
The distance between the remote control and
the sensor(s) should not exceed 8 m (26 ft.)
Refer to the illustration for the location of
the infrared (IR) remote control sensor(s).
Approx. 30°
Remove the battery cover from the rear of the remote control by pressing the
finger grip and sliding it down.
Remove any existing batteries (if necessary) and install two AAA batteries.
Observe the battery’s polarities as indicated.
Replace the battery cover by aligning it with the base and pushing it back into
position.
• Avoid leaving the remote control and batteries in excessive heat or a humid
environment.
• Replace only with the same or equivalent type recommended by the battery
manufacturer.
• Dispose of the used batteries according to the manufacturer’s instructions and
local environment regulations for your region.
• If the batteries are drained or if you will not be using the remote control for an
extended period of time, remove the batteries to avoid damage to the remote
control.
This section provides detailed instructions for setting up your projector.
Personal preference and room layout will decide the installation location. Consider
the following:
• Size and Position of your screen.
• Location of a suitable power outlet.
• Location and Distance between the projector and other equipment.
The projector is designed to be installed in one of the following locations:
The projector is placed near the floor in
front of the screen.
The projector is suspeneded upside-
down from the ceiling in front of the
screen.
The projector is suspended upside-down
from the ceiling behind the screen.
A special rear projection screen
is required.
The projector is placed near the floor
behind the screen.
A special rear projection screen
is required.
See “Specifications” on page 61 for the native display resolution of this
projector.
•
(a)
(d)
(c)
(b)
(e)
(f)
(a)
(c)
(b)
(e)
(f)
(d)
•
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(e) = Screen / (f) = Center of Lens
in. mm in. mm in. mm in. mm in. mm in. mm
60 1524 59 1491 76 1938 29 747 2.9 74.7 2.9 75
70 1778 68 1739 89 2261 34 872 3.4 87.2 3.4 87
80 2032 78 1987 102 2584 39 996 3.9 99.6 3.9 100
90 2286 88 2236 114 2907 44 1121 4.4 112.1 4.4 112
100 2540 98 2484 127 3229 49 1245 4.9 124.5 4.9 125
110 2794 108 2733 140 3552 54 1370 5.4 137.0 5.4 137
120 3048 117 2981 153 3875 59 1494 5.9 149.4 5.9 149
130 3302 127 3229 165 4198 64 1619 6.4 161.9 6.4 162
140 3556 137 3478 178 4521 69 1743 6.9 174.3 6.9 174
150 3810 147 3726 191 4844 74 1868 7.4 186.8 7.4 187
160 4064 156 3975 203 5167 78 1992 7.8 199.2 7.8 199
170 4318 166 4223 216 5490 83 2117 8.3 211.7 8.3 212
180 4572 176 4472 229 5813 88 2241 8.8 224.1 8.8 224
190 4826 186 4720 242 6136 93 2366 9.3 236.6 9.3 237
200 5080 196 4968 254 6459 98 2491 9.8 249.1 9.8 249
in. mm in. mm in. mm in. mm in. mm in. mm
60 1524 54 1368 70 1779 27 686 2.7 69 2.7 69
70 1778 63 1596 82 2075 32 800 3.2 80 3.2 80
80 2032 72 1824 93 2371 36 914 3.6 91 3.6 91
90 2286 81 2052 105 2668 41 1029 4.1 103 4.1 103
100 2540 90 2280 117 2964 45 1143 4.5 114 4.5 114
110 2794 99 2508 128 3261 50 1257 5.0 126 5.0 126
120 3048 108 2736 140 3557 54 1372 5.4 137 5.4 137
130 3302 117 2964 152 3854 59 1486 5.9 149 5.9 149
140 3556 126 3192 163 4150 63 1600 6.3 160 6.3 160
150 3810 135 3420 175 4446 68 1715 6.8 171 6.8 171
160 4064 144 3648 187 4743 72 1829 7.2 183 7.2 183
170 4318 153 3876 198 5039 77 1943 7.7 194 7.7 194
180 4572 162 4104 210 5336 81 2057 8.1 206 8.1 206
190 4826 171 4332 222 5632 86 2172 8.6 217 8.6 217
200 5080 180 4560 233 5929 90 2286 9.0 229 9.0 229
There is a 3% tolerance among these numbers due to optical component
variations. It is recommended to physically test the projection size and
distance before permanently installing the projector.
If you buy a third-party mount, please use the correct screw size. Screw size
can vary depending on the thickness of the mounting plate.
To ensure the most secure installation, please use a ViewSonic® wall or ceiling
mount.
Ensure the screws used to attach a mount to the projector meet the following
specifications:
• Screw type: M4 x 8
• Maximum Screw length: 8 mm
65.89
65.89
113.54 60.01
• Avoid installing the projector near a heat source.
• Keep at least a 10 cm gap between the ceiling and the bottom of the
projector.
The projector has several built-in security features to prevent theft, access, or
accidental setting changes.
To help prevent the projector from being stolen, use a security slot locking device
to secure the projector to a fixed object.
Below is an example of setting up a security slot locking device:
The security slot can also be used as a safety anchor if the projector is
mounted to the ceiling.
To help prevent unauthorized access or use, the projector offers a password
security option. The password can be set through the On-Screen Display (OSD)
Menu.
Make note of your password, and keep it in a safe place.
Press to open the OSD Menu and go to: > and
press .
Highlight and select
by pressing / .
As pictured to the right, the four
arrow keys ( , , , ) represent
4 digits (1, 2, 3, 4). Press the arrow
keys to enter a six digit password.
Confirm the new password by re-entering the new password. Once the password
is set, the OSD Menu will return to the page.
Press to leave the OSD Menu.
Once set, the correct password must be entered every time the projector is
started.
Press to open the OSD Menu and go to: > >
.
Press , the message, ‘INPUT CURRENT PASSWORD’ will appear.
Enter the old password.
If the password is correct, the message, ‘INPUT NEW PASSWORD’ will
appear.
If the password is incorrect, a password error message will appear for 5
seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can
try again or press to cancel.
Enter a new password.
Confirm the new password by re-entering the new password.
To leave the OSD Menu, press.
The digits being input will display as asterisks(*).
Press to open the OSD Menu and go to: > >
.
Press / to select .
The message, “Input Password” will appear. Enter the current password.
If the password is correct, the OSD Menu returns to the Password page with
“” shown in the row of .
If the password is incorrect, a password error message will appear for 5
seconds followed by the message, ‘INPUT CURRENT PASSWORD’. You can
try again or press to cancel.
Please keep the old password, as you will need it to reactivate the password
function.
If the password function is activated, you will
be asked to enter the six-digit password every
time you turn on the projector. If you enter the
wrong password, the password error message,
as pictured to the right, will appear for 5
seconds, and the message ‘INPUT PASSWORD’
follows.
You can retry or if you do not remember, you can use the “Password Recall
Procedure”.
If you enter an incorrect password 5 times in succession, the projector will
automatically shut down for a short time.
When the message ‘INPUT CURRENT
PASSWORD’ appears, press and hold
for 3 seconds. The projector will
display a coded number on the screen.
Write down the number and turn off your
projector.
Seek help from the local service center to
decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the
projector.
With the control keys on the projector locked, you can prevent your settings from
being changed accidentally (by children, for example).
When the is On, no control keys on the projector will operate
except .
Press to open the OSD Menu and go to: > .
Press/to select.
Selectand press to confirm.
To release panel key lock, press and hold on the projector for 3 seconds.
You can also use the remote control to enter the >
menu and select .
This section guides you on how to connect the projector with other equipment.
Connect the power cord to the AC IN jack at the rear of the projector.
Plug the power cord into a power outlet.
When installing the projector, incorporate a readily accessible disconnect
device in the xed wiring, or connect the power plug to an easily accessible
outlet near the unit. If a fault should occur during operaon of the projector,
use the disconnect device to switch o the power supply, or disconnect the
power plug.
Connect one end of an HDMI cable to the HDMI port of your video device. Then
connect the other end of the cable to the or port of your projector.
Connect one end of a VGA cable to the VGA port of your computer. Then connect
the other end of the cable to the port of your projector.
Some notebooks do not turn on their external displays automacally when
connected to a projector. You may have to adjust your notebook’s projecon
sengs.
After establishing the VGA Connection, connect one end of a VGA cable to the VGA
port of your monitor. Then connect the other end of the cable to the
port of your projector.
The projector is equipped with speakers, however, you can also connect external
speakers to the port of the projector.
The audio output is controlled by the projector’s and sengs.
Press the buon to turn on the projector.
The lamp will light up, and a will play.
The Power Indicator Light stays green when the projector is On.
• If the projector is sll hot from previous use, it will run the cooling fan for 90
seconds before acvang the lamp.
• To maintain lamp life, once you turn the projector On, wait at least ve (5)
minutes before turning it o.
Turn on all of the connected equipment, i.e. notebook, and the projector will
start to search for an input source.
If the projector detects an input source, the Source Selecon Bar will appear. If
an input source is not detected, the message, ‘No Signal’ will appear.
If the projector is activated for the first time, select your OSD language following
the on-screen instructions.
Press the or buon and a conrmaon message will appear to prompt
you to press the or buon a second me. Addionally you can press
any other buon to cancel.
If you do not respond in a few seconds aer the rst press, the message will
disappear.
Once the cooling process nishes, a will play.
Disconnect the power cord from the power outlet if the projector will not be
used for an extended period of me.
• To protect the lamp, the projector will not respond to commands during the
cooling process.
• Do not unplug the power cord before the projector completely shuts down.
The projector can be connected to multiple devices at the same time. However, it
can only display one full screen at a time.
If you want the projector to automatically search for the input source, ensure the
function in the menu is .
The can also be manually selected by pressing one of the source
selection buttons on the remote control, or by cycling through the available input
sources.
On Off
HDMI 1 HDMI 2COMP
Source
Pattern
Brightness
Contrast
Aspect
Color
Temp
Eco
Mode
StandardGaming Sports
Movie User
Blank
3D
Auto
Sync
ID Set 1 2
3 4 5
6 7 8
To manually select the input source do the following:
Press , and a source selecon menu will appear.
Press unl your desired signal is selected and press .
Once detected, the selected source informaon will be displayed on the screen
for a few seconds.
If there are mulple devices connected to the projector, repeat steps 1-2 to
search for another source.
The projector is equipped with one (1) adjuster foot. Adjusting the foot will change
the projector’s height and the vertical projection angle. Carefully adjust the feet to
fine tune the projected image’s position.
Sometimes, you may need to improve the picture quality. To do this, press
on the remote control. Within five (5) seconds, the built-in Intelligent Auto
Adjustment function will re-adjust the Frequency and Clock values to provide the
best picture quality.
Upon completion, the current source information will appear in the upper left
corner for three (3) seconds.
This funcon is only available when the PC D-Sub input source (analog RGB/
COMPUTER IN) is selected.
To adjust the projected image to the size that you need, rotate the Zoom Ring.
To improve the clarity of the image, rotate the Focus Ring.
Keystoning refers to the situation where the projected image becomes a trapezoid
due to angled projection.
To correct this, besides adjusting the height of the projector, you may also:
Use the keystone keys on the projector or remote control to display the keystone
page.
Aer the keystone page is displayed, press to correct keystoning at the top of
the image. Press to correct keystoning at the boom of the image. Press
to correct keystoning at the boom of the image. Press to correct keystoning
at the right side of the image. Press to correct keystoning at the le side of the
image.
On O ff
HDMI 1 HDMI 2COMP
Source
Pattern
Brightness
Contrast
Aspect
Color
Temp
Eco
Mode
StandardGaming Sports
Movie User
Blank 3D
Auto
Sync
ID Set 1 2
345
678
EXIT
MENU
SOURCE
BLANK
MODE
COLOR
You can manually adjusts the shape and size of an image that is unevenly
rectangular on all sides.
To display the Corner Adj. page, you can do
one of the followings:
• Press .
• Open the OSD menu and go to the
> menu and press
. The page is displayed.
Use / / / to select the corner you
wish to adjust and press .
Use / to select an adjustment method that suits
your need and press .
As indicated on the screen ( / for a 45-degree
angle adjustment and / / / for a 90-degree
angle adjustment), press / / / to adjust its
shape and size. You can press or to go
back to a previous step. A long press for 2 seconds
on will reset the sengs on the corner that
you chose.
• Adjusng keystone will reset the
sengs.
• Aer the sengs have been modied, some aspect raos or mings
are not available. When that happens, reset the sengs on all 4 corners.
In order to draw the audience’s full attention to the presenter, you can press
on the projector or remote control to hide the screen image. Press any key on the
projector or remote control to restore the image.
Do not block the projecon lens as this could cause the blocking object to
become heated and deformed or even cause a re.
This section will introduce the On-Screen Display (OSD) Menu and its options.
The OSD screenshots in this manual are for reference only and may dier from
the actual design. Some of the following OSD sengs may not be available.
Please refer to the actual OSD of your projector.
The projector is equipped with an On-Screen Display (OSD) Menu for making
various adjustments. It can be accessed by pressing on the projector or
remote control.
Press to select a main menu. Then press or use to access the
sub-menu list.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the respecve
sub-menu, press . Use or to adjust/select the seng.
Aspect Ratio Auto
4:3
16:9
16:10
Native
Keystone Vertical -40~40
Horizontal -40~40
Corner Adj. Top-Right 45°/90°
Top-Left 45°/90°
Bottom-Right 45°/90°
Bottom-Left 45°/90°
Position X: -5 ~ 5, Y: - 5 ~ 5
Phase 0~31
H. Size -15~15
Zoom 0.8X ~2.0X
OverScan Off/1/2/3/4/5
3X Fast Input Inactive
Active
Color Mode Brightest
Sports
Standard
Gaming
Movie (Rec.709)
ISF Day
ISF Night
User 1
User 2
Brightness 0~100
Contrast -50~50
Color Temp. 8000K/6500K/5500K
Red Gain 0~100
Green Gain 0~100
Blue Gain 0~100
Red Offset -50~+50
Green Offset -50~+50
Blue Offset -50~+50
Advanced Color -50~50
Sharpness 0~31
Gamma 1.8/2.0/2.2/2.35/
2.5/Cubic/sRGB
Brilliantcolor Off/1/2/3/4/
5/6/7/8/9/10
Noise Reduction 0~31
Color Management Primary Color
Hue
Saturation
Gain
Reset Color Settings Reset
Cancel
ISF Mode (Password-protected)
Auto Power On Signal Disable/VGA/HDMI/
All
CEC Disable/Enable
Direct Power On Disable/Enable
Smart Energy Auto Power Off Disable/10 min/20
min/30 min
Sleep Timer Disable/30 min/1
hr/2hr/3 hr/4 hr/ 8
hr/12 hr
Power Saving Disable/Enable
Standby Settings VGA Loop Through Off/On
Audio Pass Through Off/On
Quick Power Off Disable
Enable
USB A Power On
Off
Audio Settings Mute Off/On
Audio Volume 0~20
Power On/Off Ring Tone Off/On
Presentation Timer Timer Period 1~240 m
Timer Display Always/1 min/2 min/
3 min/Never
Timer Position
Top-Left/Bottom-Left/
Top-Right/Bottom-Right
Timer Counting Direction Count Down/Count Up
Sound Reminder Off/On
Start Counting/Off
Pattern Off
Test Card
Blank Timer Disable/5 min/10 min/15 min/20 min/25 min/30
min
Message Off
On
Splash Screen Black
Blue
ViewSonic
3D Settings 3D Sync Auto
Off
Frame Sequential
Frame Packing
Top-Bottom
Side-by-Side
3D Sync Invert Disable/Invert
Save 3D Settings Yes/No
HDMI Settings HDMI Format Auto/RGB/YUV
HDMI Range
Auto/Enhanced/Normal
Lamp Settings Lamp Mode Normal/Eco/
Dynamic Eco/
SuperEco+
Reset Lamp Hours Reset/Cancel
Lamp Hours Information Lamp Usage Time
Normal
Eco
Dynamic Eco
SuperEco+
Equivalent Lamp Hour
Reset Settings Reset
Cancel
Language Multi-Language OSD Selection
Projector Position Front Table
Rear Table
Rear Ceiling
Front Ceiling
Menu Settings Menu Display Time 5 sec/10 sec/15 sec/20
sec/25 sec/30 sec
Menu Position Center/Top-Left/
Top-Right/
Bottom-Left/
Bottom-Right
High Altitude Mode Off
On
Quick Auto Search Off
On
Security Settings Change Password
Power On Lock Off/On
Panel Key Lock Off
On
Remote Control Code
1/2/3/4/5/6/7/8
Control Method RS-232
USB
Baud Rate 2400/4800/9600/14400/19200/
38400/57600/115200
Source
Color Mode
Resolution
Color System
Firmware Version
3X Fast Input
S/N
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu. Then press or use to access
the menu.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the respecve
sub-menu, press . Use or to adjust/select the seng.
Aspect Ratio Auto
Scales an image proportionally to fit the projector’s native
resolution in its horizontal width. This is suitable for the
incoming image which is neither in 4:3 nor 16:9 and you want
to make most use of the screen without altering the image’s
aspect ratio.
4:3
Scales an image so that it is displayed in the center of the
screen with a 4:3 aspect ratio. This is most suitable for 4:3
images like computer monitors, standard definition TV, and
4:3 aspect DVD movies, as it displays them without aspect
alteration.
16:9
Scales an image so that it is displayed in the center of the
screen with a 16:9 aspect ratio. This is most suitable for images
which are already in a 16:9 aspect, like high definition TV, as it
displays them without aspect alteration.
16:10
Scales an image so that it is displayed in the center of the
screen with a 16:10 aspect ratio. This is most suitable for
images which are already in a 16:10 aspect, as it displays them
without aspect alteration.
Native
Projects an image as its original resolution and resizes it
to fit within the display area. For input signals with lower
resolutions, the projected image will be displayed in its original
size.
Keystone Adjusts the keystoning situation where the projected image
becomes a trapezoid due to angled projection.
Corner Adj. Adjusts the shape and size of an image that is unevenly
rectangular on all sides.
Position Adjust the position of the projected image.
• This funcon is only available when a PC input signal is
selected.
• The adjustment range may vary under dierent mings.
Phase Adjusts the clock phase to reduce image distortion.
This funcon is only available when a PC input signal is
selected.
H. Size Adjusts the horizontal width of the image.
This funcon is only available when a PC input signal is
selected.
Zoom Magnifies the projected image and allows you to navigate the
image.
OverScan Adjusts the overscan rate from 0% to 5%.
This funcon is only available when a Composite Video or
HDMI input signal is selected.
3X Fast Input This function is favorable to frame rate reducing. Quick
response time in native timing can be achieved. When enabled,
the following settings will return to factory preset values:
Aspect Ratio, Position, Zoom, OverScan.
This funcon is only available when a nave ming input
signal is selected.
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu. Then press or use to access
the menu.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the respecve
sub-menu, press . Use or to adjust/select the seng.
Color Mode Brightest
Maximizes the brightness of the projected image. This mode
is suitable for environments where extra-high brightness is
required, such as using the projector in well lit rooms.
Sports
Designed for viewing sports in well-lit environments.
Standard
Designed for normal circumstances in a daylight environment.
Gaming
Suitable for playing video games in a bright living room.
Movie (Rec.709)
For playing colorful movies, video clips from digital cameras or
DVs through the PC input for best viewing in a blackened (low
light) environment.
ISF Day/ISF Night
Only available when is On.
User 1/User 2
Recalls the customized settings. After User 1/User 2 is selected,
some of the sub-menus under the menu can be
adjusted, according to your selected input source.
Brightness The higher the value, the brighter the image.
Adjust this option so the
black areas of the image
appear just as black and
details in the dark area are
more visible.
Contrast Use this to set the peak white level after you have
previously adjusted the
setting.
Color Temp. 8000K
Images appear bluish white.
6500K
Images maintain a normal white appearance.
5500K
Images appear reddish white.
To set a custom color temperature, you can further adjust the
following items:
Red Gain/Green Gain/Blue Gain
Adjusts the Contrast levels of Red, Green, and Blue.
Red Offset/Green Offset/Blue Offset
Adjusts the Brightness levels of Red, Green, and Blue.
Advanced Color
A lower setting produces less saturated colors. If the setting
is too high, colors will be overpowering and may appear
unrealistic.
Sharpness
A higher value will sharpen the image, while a lower value will
soften the image.
Gamma
Gamma refers to the brightness level of the projector’s
grayscale levels.
Brilliantcolor
This feature utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone
images, which are common in video and natural scenes, so the
projector reproduces images in realistic and true colors. If you
prefer images with that quality, select a level that suits your
need.
Advanced Noise Reduction
This function reduces electrical image noise caused by different
media players. The higher the setting, the less the noise. (Not
available when input signal is HDMI.)
Color Management
Only in permanent installations with controlled lighting levels
such as boardrooms, lecture theaters, or home theaters,
should color management be considered. Color management
provides fine color control adjustment to allow for more
accurate color reproduction. Select Primary Color first and
adjust its range/values in Hue, Saturation and Gain.
Reset Color Settings Returns current image settings to the factory preset values.
ISF Mode The ISF calibration menu is password protected and only
accessible by authorized ISF calibrators. The ISF (Imaging
Science Foundation) has developed carefully crafted, industry-
recognized standards for optimal video performance and has
implemented a training program for technicians and installers
to use these standards to obtain optimal picture quality from
ISF certified display devices. Accordingly, we recommend
that setup and calibration be performed by an ISF certified
installation technician.
• The default password is: .
• For more informaon, go to www.imagingscience.com or
contact the dealer or retailer from whom you purchased
the projector.
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu. Then press or use
to access the menu.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the respecve
sub-menu, press . Use or to adjust/select the seng.
Auto Power On Signal
Selecting VGA/HDMI allows the projector to turn on
automatically once the VGA/HDMI signal is fed through the
VGA/HDMI cable. You can also select All and the projector will
turn on automatically upon receiving either a VGA or HDMI
signal.
CEC
This projector supports CEC (Consumer Electronics Control)
function for synchronized power on/off operation via HDMI
connection. That is, if a device that also supports CEC function
is connected to the HDMI input of the projector, when the
projector’s power is turned off, the power of the connected
device will also be turned off automatically. When the power
of the connected device is turned on, the projector’s power
will be turned on automatically.
• In order for the CEC funcon to work properly, make sure
that the device is correctly connected to the HDMI input
of the projector via an HDMI cable, and its CEC funcon is
turned on.
• Depending on the connected device, the CEC funcon may
not work.
Direct Power On
Allows the projector to turn on automatically once power is fed
through the power cord.
Smart Energy Auto Power Off
Allows the projector to turn off automatically after a set
period of time once no input source is detected to prevent
unnecessary waste of lamp life.
Sleep Timer
Allows the projector to turn off automatically after a set period
of time to prevent unnecessary waste of lamp life.
Power Saving
Lowers power consumption if no input source is detected.
When Enable is selected, the projector lamp mode will change
to SuperEco+ mode after no signal is detected for five (5)
minutes. This will also help prevent any unnecessary waste of
lamp life.
Standby Settings The functions below are available in standby mode (plugged in,
but not turned on).
VGA Loop Through
When selecting On, the projector outputs the signal received
only from COMPUTER IN.
Audio Pass Through
When selecting On, the projector outputs an audio signal when
the Audio In and Audio Out sockets are correctly connected to
a proper device.
Quick Power Off Enable
The projector will not enter the cooling process after being
shut down.
Disable
The projector will enter the normal cooling process after being
shut down.
If you aempt to restart the projector right aer it’s been
turned o, it may not be turned on successfully and will
rerun its cooling procedure.
USB A Power When On, the USB Type A port can supply power, and the
Control Method will automatically switch to RS-232.
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu. Then press or use to access the
menu.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the respecve
sub-menu, press . Use or to adjust/select the seng.
Audio Settings Mute
Select On to temporarily turn off the projector’s internal
speaker or the volume being output from the audio output
jack.
Audio Volume
Adjusts the volume level of the projector’s internal speaker or
the volume being output from the audio output jack.
Power On/Off Ring Tone
Turns on/off the ring tone during the starting up and shutting
down process.
Presentation Timer Presentation timer can indicate the presentation time on the
screen to help you achieve better time management when
giving presentations.
Timer Period
Sets the time period. If the timer is already on, the timer will
restart whenever the Timer Period is reset.
Timer Display
Allows you to decide if you want the timer to show up on the
screen for one of the following time periods:
Always: Displays the mer on screen throughout the
presentaon me.
1 min/2 min/3 min: Displays the mer on screen in the
last 1/2/3 minute(s).
Never: Hides the mer throughout the presentaon me.
Timer Position
Sets the timer position.
Timer Counting Direction
Sets your desired counting direction between:
Count Down: Decreases from the preset me to 0.
Count Up: Increases from 0 to the preset me.
Sound Reminder
Allows you to decide if you want to activate a sound reminder.
Once enabled, a double beep sound will be heard at the last 30
seconds of counting down/up, and a triple beep sound will be
produced when the timer is up.
Start Counting/Off
Select Start Counting to activate the timer. Select Off to cancel
it.
Pattern Helps adjust the image size and focus, and checks for distortion
in the projected image.
Blank Timer Allows the projector to return the image automatically after a
period of time when there is no action taken on the blank
screen. To display the blank screen, press on the projector
or remote control.
Do not block the projecon lens as this could cause the
blocking object to become heated and deformed or even
cause a re.
Message Sets reminder messages, i.e. “Blank” message, On or Off.
Splash Screen Selects which logo screen will appear during projector start-up.
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu. Then press or use to
access the menu.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the respecve
sub-menu, press . Use or to adjust/select the seng.
3D Settings This projector features a 3D function which enables you to
enjoy 3D movies, videos, and sporting events in a more realistic
way by presenting the depth of the images. You need to wear a
pair of 3D glasses to view 3D images.
3D Sync
The default setting is Auto and the projector automatically
chooses an appropriate 3D format when detecting 3D
contents. If the projector cannot recognize the 3D format,
choose a 3D mode.
3D Sync Invert
When you discover the inversion of the image depth, enable
this function to correct the problem.
Save 3D Settings
Saves current 3D settings. 3D settings will automatically be
applied if the same resolution and input source are selected.
When the 3D Sync funcon is on:
• The brightness level of the projected image will decrease.
• The Color Mode, Lamp Mode, Zoom, and OverScan cannot
be adjusted.
HDMI Settings HDMI Format
Select a suitable color space according to the color space
setting of the output device connected.
Auto: Sets the projector to detect the color space seng
of the input signal automacally.
RGB: Sets the color space as RGB.
YUV: Sets the color space as YUV.
HDMI Range
Select a suitable HDMI color range according to the color range
setting of the output device connected.
Auto: Sets the projector to detect the HDMI range of the
input signal automacally.
Enhanced: Sets the HDMI color range as 0 - 255.
Normal: Sets the HDMI color range as 16 - 235.
Lamp Settings Lamp Mode
Normal: Provides full lamp brightness.
Eco: Reduces lamp power consumpon by 30% and
lowers brightness to extend the lamp life and decreases
the fan noise.
Dynamic Eco: Reduces lamp power consumpon by up to
65% depending on the content brightness level.
SuperEco+: Reduces lamp power consumpon by 60%
and lowers brightness to extend the lamp life and
decreases the fan noise.
To control the lamp temperature, Eco Mode will be
switched on for 10 minutes every 4 hours when the
Lamp Mode is set as SuperEco+.
Color Mode, Color Temp. and Reset Color Sengs will not
be available when the Lamp Mode is set as SuperEco+.
Reset Lamp Hours
Resets the lamp timer after a new lamp is installed. For
changing the lamp, please contact qualified service personnel.
Lamp Hours Information
Lamp Usage Time: Displays the number of hours the
lamp has been used.
Equivalent Lamp Hour: Displays the overall lamp life. The
method of calculang the equivalent light source hour is
as follows:
Total (equivalent) Lamp Hour = 5 x (hours used in
Normal mode) + 2 x (hours used in Eco mode) + 1.67 x
(hours used in Dynamic Eco mode) + 1 x (hours used in
SuperEco+ mode)
Reset Settings Returns all settings to the factory preset values. When
using Reset Settings, the following settings will still remain:
Zoom, Keystone, Corner Adj., Language, Projector Position,
ISF Mode, USB A Power, High Altitude Mode, Security Settings,
Remote Control Code, Control Method and Baud Rate.
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu. Then press or use to access
the menu.
Press to select the menu opon. Then press to display its sub-menu,
or press to adjust/select the seng.
Some sub-menu opons may have another sub-menu. To enter the
respecve sub-menu, press . Use or to adjust/select the
seng.
Language Sets the language for the On-Screen Display (OSD) Menu.
Projector Position Selects a proper position for the projector.
Menu Settings Menu Display Time
Sets the length of time the OSD Menu will remain active after
your last interaction.
Menu Position
Sets the OSD Menu’s position.
High Altitude Mode We recommend you use the High Altitude Mode when your
environment is between 1,500 m to 3,000 m above sea level,
and ambient temperature is between 5°C–25°C.
• Do not use High Altude Mode if your environment is
between 0 to 1,499 m, and the temperature is between
5°C to 35°C. If used, the projector will become over
cooled.
• Using “High Altude Mode” may cause more operang
noise, as the fan speed will be increased to improve
cooling and performance.
Quick Auto Search Allows the projector to automatically search for the signals.
Security Settings See “Using the Password Function” on page 20.
Panel Key Lock Locks the control keys on the projector.
Remote Control Code Sets the remote control code for this projector (between 1~8).
When multiple adjacent projectors are in operaon at the same
me, switching the codes can prevent interference from other
remote controls. Aer the remote control code is set, switch to
the same ID for the remote control to control this projector.
To switch the code for the remote control, press and
the number buon corresponding to the remote control code
together for 5 seconds or more. The inial code is set to 1.
When the code is switched to 8, the remote control can control
every projector.
If dierent codes are set on the projector and remote
control, there will be no response from the remote
control. When that happens, a message will display to
remind you to switch the code for the remote control.
Control Method Allows you to select a preferred control port: through the
RS-232 port or the USB port. When selecting USB, USB A Power
will be switched to Off automatically.
Baud Rate Selects a baud rate that is identical with your computer’s so
that you can connect the projector using a suitable RS-232
cable and control the projector with RS-232 commands
Press the buon to display the On-Screen Display (OSD) Menu.
Press to select the menu and display its contents.
Source Shows the current input source.
Color Mode Shows the selected mode in the IMAGE menu.
Resolution Shows the native resolution of the input source.
Color System Shows input system format.
Firmware Version Shows the current firmware version.
3X Fast Input Shows whether the function is activated or not.
S/N Shows the serial number for this projector.
61
Specifications
Item Category Specifications
Projector Type DLP Lamp
Display Size 60”~300”
Brightness (Lumens) 2000 ANSI
Throw Ratio 1.13~1.47 (95”±3%@2.36m)
Lens 1.3x±2% Optical Zoom
Lamp Type OSRAM P-VIP 245/0.8 E30.5
Display System 1-CHIP DMD
Input Signal VGA fh: 15K~102KHz, fv:48~120Hz,
Pixel rate: 170MHz
HDMI fh: 15K~102KHz, fv:23~120Hz,
Pixel rate: 170MHz
Resolution Native 1920 x 1080
Power Adapter1Input Voltage AC 100-240V, 50/60 Hz (auto switch)
Operating
conditions
Temperature 0°C to 40°C (32°F to 104°F)
Humidity 0% to 90% (non-condensing)
Altitude 0 to 1,499 m at 5°C to 35°C
1,500 to 3,000 m at 5°C to 25°C
Storage
conditions
Temperature -20°C to 60°C (non-condensing)
Humidity 0% to 90% (non-condensing)
Altitude 0 to 1,219 m at -20°C to 30°C
Dimensions Physical
(W x H x D)
312 x 108 x 222 mm
(12.3” x 4.3” x 8.7”)
Weight Physical 3.91 kg (8.62 lbs)
Power Saving
Modes
On2310W (Typical)
Off < 0.5W (Standby)
1 Please use the power adapter from ViewSonic® or an authorized source only.
2 The test condition follows EEI standards.
Appendix
312 mm (W) x 108 mm (H) x 222 mm (D)
EXIT
MENU
SOURCE
BLANK
MODE
COLOR
222
mm
312 mm
108 mm
62.72 mm 91.81 mm
720 x 400 720 x 400_70 70.087 31.469 28.3221
640 x 480 VGA_60 59.94 31.469 25.175 Supported Supported Supported
VGA_72 72.809 37.861 31.5
VGA_75 75 37.5 31.5
VGA_85 85.008 43.269 36
800 x 600 SVGA_60 60.317 37.879 40 Supported Supported Supported
SVGA_72 72.188 48.077 50
SVGA_75 75 46.875 49.5
SVGA_85 85.061 53.674 56.25
SVGA_120 (Reduce
Blanking)
119.854 77.425 83 Supported
1024 x 768 XGA_60 60.004 48.363 65 Supported Supported Supported
XGA_70 70.069 56.476 75
XGA_75 75.029 60.023 78.75
XGA_85 84.997 68.667 94.5
XGA_120 (Reduce
Blanking)
119.989 97.551 115.5 Supported
1152 x 864 1152 x 864_75 75 67.5 108
1024 x 576 NB Timing 60 35.82 46.966
1024 x 600 NB Timing 64.995 41.467 51.419
1280 x 720 1280 x 720_60 60 45 74.25 Supported Supported Supported
1280 x 768 1280 x 768_60 59.87 47.776 79.5 Supported Supported Supported
1280 x 800 WXGA_60 59.81 49.702 83.5 Supported Supported Supported
WXGA_75 74.934 62.795 106.5
WXGA_85 84.88 71.554 122.5
WXGA_120 (Reduce
Blanking)
119.909 101.563 146.25 Supported
1280 x 1024 SXGA_60 60.02 63.981 108 Supported Supported
SXGA_75 75.025 79.976 135
SXGA_85 85.024 91.146 157.5
1280 x 960 1280 x 960_60 60 60 108 Supported Supported
1280 x 960_85 85.002 85.938 148.5
1360 x 768 1360 x 768_60 60.015 47.712 85.5 Supported Supported
1440 x 900 WXGA+_60 59.887 55.935 106.5 Supported Supported
1400 x 1050 SXGA+_60 59.978 65.317 121.75 Supported Supported
1600 x 1200 UXGA 60 75 162 Supported Supported
1680 x 1050 1680x1050_60 59.954 65.29 146.25 Supported Supported
640 x 480@67Hz MAC13 66.667 35 30.24
832 x 624@75Hz MAC16 74.546 49.722 57.28
1024 x 768@75Hz MAC19 74.93 60.241 80
1152 x 870@75Hz MAC21 75.06 68.68 100
1920 x 1080 (VESA) 1920 x 1080_60 60 67.5 148.5
640 x 480 VGA_60 59.94 31.469 25.175 Supported Supported Supported
VGA_72 72.809 37.861 31.5
VGA_75 75 37.5 31.5
VGA_85 85.008 43.269 36
720 x 400 720 x 400_70 70.087 31.469 28.3221
800 x 600 SVGA_60 60.317 37.879 40 Supported Supported Supported
SVGA_72 72.188 48.077 50
SVGA_75 75 46.875 49.5
SVGA_85 85.061 53.674 56.25
SVGA_120 (Reduce
Blanking)
119.854 77.425 83 Supported
1024 x 768 XGA_60 60.004 48.363 65 Supported Supported Supported
XGA_70 70.069 56.476 75
XGA_75 75.029 60.023 78.75
XGA_85 84.997 68.667 94.5
XGA_120 (Reduce
Blanking)
119.989 97.551 115.5 Supported
1152 x 864 1152 x 864_75 75 67.5 108
1024 x 576 NB Timing 60 35.82 46.966
1024 x 600 NB Timing 64.995 41.467 51.419
1280 x 720 1280 x 720_60 60 45 74.25 Supported Supported Supported
1280 x 768 1280 x 768_60 59.87 47.776 79.5 Supported Supported Supported
1280 x 800 WXGA_60 59.81 49.702 83.5 Supported Supported Supported
WXGA_75 74.934 62.795 106.5
WXGA_85 84.88 71.554 122.5
WXGA_120 (Reduce
Blanking)
119.909 101.563 146.25 Supported
1280 x 1024 SXGA_60 60.02 63.981 108 Supported Supported
SXGA_75 75.025 79.976 135
SXGA_85 85.024 91.146 157.5
1280 x 960 1280 x 960_60 60 60 108 Supported Supported
1280 x 960_85 85.002 85.938 148.5
1360 x 768 1360 x 768_60 60.015 47.712 85.5 Supported Supported
1440 x 900 WXGA+_60 59.887 55.935 106.5 Supported Supported
1400 x 1050 SXGA+_60 59.978 65.317 121.75 Supported Supported
1600 x 1200 UXGA 60 75 162 Supported Supported
1680 x 1050 1680x1050_60 59.954 65.29 146.25 Supported Supported
640 x 480@67Hz MAC13 66.667 35 30.24
832 x 624@75Hz MAC16 74.546 49.722 57.28
1024 x 768@75Hz MAC19 75.020 60.241 80
1152 x 870@75Hz MAC21 75.06 68.68 100
1920 x 1080 (VESA) 1920 x 1080_60 60 67.5 148.5
480i 720(1440) x 480 15.73 59.94 27 Supported
480p 720 x 480 31.47 59.94 27 Supported Supported Supported
576i 720(1440) x 576 15.63 50 27 Supported
576p 720 x 576 31.25 50 27 Supported Supported Supported
720/50p 1280 x 720 37.5 50 74.25 Supported Supported
720/60p 1280 x 720 45 60 74.25 Supported Supported
1080/50i 1920 x 1080 28.13 50 74.25 Supported
1080/60i 1920 x 1080 33.75 60 74.25 Supported
1080/24P 1920 x 1080 27 24 74.25 Supported Supported
1080/50P 1920 x 1080 56.25 50 148.5 Supported Supported
1080/60P 1920 x 1080 67.5 60 148.5 Supported Supported
On NEC-F2 83 F4 4F B0
Off NEC-F2 83 F4 4E B1
COMP NEC-F2 83 F4 41 BE
HDMI/HDMI 1 NEC-F2 83 F4 58 A7
HDMI 2 NEC-F2 83 F4 59 A6
Auto Sync NEC-F2 83 F4 8 F7
Source NEC-F2 83 F4 40 BF
Up/ NEC-F2 83 F4 0B F4
Left/ NEC-F2 83 F4 0E F1
Enter/ (Corner
Adjustment)
NEC-F2 83 F4 15 EA
Right/ NEC-F2 83 F4 0F F0
Down/ NEC-F2 83 F4 0C F3
Menu NEC-F2 83 F4 30 CF
(INFORMATION)
NEC-F2 83 F4 97 68
Exit NEC-F2 83 F4 28 D7
Aspect NEC-F2 83 F4 13 EC
Freeze NEC-F2 83 F4 03 FC
Pattern NEC-F2 83 F4 55 AA
Blank NEC-F2 83 F4 7 F8
PgUp NEC-F2 83 F4 06 F9
PgDn NEC-F2 83 F4 05 FA
(Mute) NEC-F2 83 F4 14 EB
(Volume Down) NEC-F2 83 F4 83 7C
(Volume Up) NEC-F2 83 F4 82 7D
(Zoom in) NEC-F2 83 F4 67 98
(Zoom out) NEC-F2 83 F4 68 97
Eco Mode NEC-F2 83 F4 2B D4
Color Mode NEC-F2 83 F4 10 EF
Code 1 83F4
Code 2 93F4
Code 3 A3F4
Code 4 B3F4
Code 5 C3F4
Code 6 D3F4
Code 7 E3F4
Code 8 F3F4
1NC 2RX
3TX 4NC
5GND 6NC
7RTSZ 8CTSZ
9NC
Baud Rate 115200 bps (default)
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
Power Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Power Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Power Write ON/OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x34 0x00 0x91
Power Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E
Keystone-
Horizontal
Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E
Keystone-
Horizontal
Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F
Keystone-
Horizontal
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31 0x8F
Color mode Write ISF Day 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x16 0x7F
Color mode Write ISF Night 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x17 0x80
ISF mode Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x38 0x01 0x97
ISF mode Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x38 0x00 0x96
ISF mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x38 0x97
Reset Settings Write Reset Settings 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Reset Color
Settings
Write Reset Color
Settings
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87
Splash Screen Write Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash Screen Write Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Splash Screen Write ViewSonic 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Splash Screen Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68
Quick Power Off Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
Quick Power Off Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Quick Power Off Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B 0x69
High Altitude Mode Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High Altitude Mode Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
High Altitude Mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C 0x6A
Lamp Mode Write Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Lamp Mode Write Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Lamp Mode Write Dynamic Eco 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x02 0x6F
Lamp Mode Write SuperEco+ 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x03 0x70
Lamp Mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E
Message Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Message Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Message Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85
Projector Position Write Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Projector Position Write Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Projector Position Write Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Projector Position Write Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Projector Position Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F
3D Sync Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
3D Sync Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
3D Sync Write Frame
Sequential
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x02 0x80
3D Sync Write Frame Packing 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x03 0x81
3D Sync Write Top Bottom 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x04 0x82
3D Sync Write Side by Side 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x05 0x83
3D Sync Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F
3D Sync Invert Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
3D Sync Invert Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
3D Sync Invert Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80
Contrast Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Contrast Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61
Brightness Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Brightness Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62
Aspect ratio Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio Write 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio Write 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio Write 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Aspect ratio Write Native 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x09 0x6B
Aspect ratio Write Cycle 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x31 0x00 0x90
Aspect ratio Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63
Auto Adjust Write Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Horizontal position Write Shift Right 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Horizontal position Write Shift Left 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Horizontal position Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65
Vertical position Write Shift Up 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Vertical position Write Shift Down 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
Vertical position Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66
Color temperature Write 5500K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
Color temperature Write 6500K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
Color temperature Write 8000K 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
Color temperature Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67
Color temperature-
Red gain
Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x00 0x00 0x99
Color temperature-
Red gain
Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x00 0x01 0x9A
Color temperature-
Red gain
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3B 0x9A
Color temperature-
Green gain
Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x01 0x00 0x9A
Color temperature-
Green gain
Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x01 0x01 0x9B
Color temperature-
Green gain
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3C 0x9B
Color temperature-
Blue gain
Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x02 0x00 0x9B
Color temperature-
Blue gain
Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3A 0x02 0x01 0x9C
Color temperature-
Blue gain
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3D 0x9C
Color temperature-
Red offset
Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x00 0x00 0x9D
Color temperature-
Red offset
Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x00 0x01 0x9E
Color temperature-
Red offset
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x3F 0x9E
Color temperature-
Green offset
Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x01 0x00 0x9E
Color temperature-
Green gain
Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x01 0x01 0x9F
Color temperature-
Green offset
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x40 0x9F
Color temperature-
Blue offset
Write Decrease 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x02 0x00 0x9F
Color temperature-
Blue offset
Write Increase 0x06 0x14 0x00 0x05 0x00 0x34 0x12 0x3E 0x02 0x01 0xA0
Color temperature-
Blue offset
Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x41 0xA0
Blank Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Blank Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68
Keystone-Vertical Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
Keystone-Vertical Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Keystone-Vertical Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
Color mode Write Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Color mode Write Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
Color mode Write Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
Color mode Write Sports 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x11 0x7A
Color mode Write Gaming 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x12 0x7B
Color mode Write Cycle 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x33 0x00 0x92
Color mode Write User1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x18 0x81
Color mode Write User2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x19 0x82
Color mode Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A
Reset current color
settings
Write Reset 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87
Primary Color Write R 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Primary Color Write G 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Primary Color Write B 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Primary Color Write C 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Primary Color Write M 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Primary Color Write Y 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Primary Color Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F
Hue / Tint Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Hue / Tint Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Hue / Tint Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70
Saturation Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Saturation Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Saturation Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71
Gain Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Gain Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Gain Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72
Sharpness Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0E 0x00 0x6C
Sharpness Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0E 0x01 0x6D
Sharpness Read Get value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0E 0x6D
Freeze Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Freeze Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60
Source input Write D-Sub/Comp. 1 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Source input Write HDMI 1 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Source input Write HDMI 2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67
Source input Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61
Quick Auto Search Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto Search Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Quick Auto Search Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62
Mute Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Mute Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61
Volume Write Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Volume Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Volume Write Write Value 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x2A 0x11 0x9A
Volume Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64
Language Write English 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
Language Write Français 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
Language Write Deutsch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
Language Write Italiano 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
Language Write Español 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
Language Write РУССКИЙ 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
Language Write 繁體中文 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
Language Write 简体中文 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
Language Write 日本語 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
Language Write 한국어 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
Language Write Swedish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
Language Write Dutch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
Language Write Turkish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
Language Write Czech 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E
Language Write Portuguese 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
Language Write Thai 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
Language Write Polish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
Language Write Finnish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
Language Write Arabic 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x12 0x73
Language Write Indonesia 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x13 0x74
Language Write Hindi 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x14 0x75
Language Write Vie 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x15 0x76
Language Write Greek 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x16 0x77
Language Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62
Lamp Usage Time Write Reset to ZERO 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Lamp Usage Time Read Get Usage Time 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63
HDMI Format Write RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85
HDMI Format Write YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86
HDMI Format Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87
HDMI Format Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86
HDMI Range Write Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86
HDMI Range Write Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87
HDMI Range Write Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88
HDMI Range Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x29 0x87
CEC Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x00 0x88
CEC Write ON 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2B 0x01 0x89
CEC Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x2B 0x89
Error status Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D 0x66
Brilliant Color Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D
Brilliant Color Write Color 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E
Brilliant Color Write Color 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x02 0x6F
Brilliant Color Write Color 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x03 0x70
Brilliant Color Write Color 4 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x04 0x71
Brilliant Color Write Color 5 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x05 0x72
Brilliant Color Write Color 6 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x06 0x73
Brilliant Color Write Color 7 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x07 0x74
Brilliant Color Write Color 8 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x08 0x75
Brilliant Color Write Color 9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x09 0x76
Brilliant Color Write Color 10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x0A 0x77
Brilliant Color Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0F 0x6E
Remote Control
Code
Write code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0
Remote Control
Code
Write code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1
Remote Control
Code
Write code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2
Remote Control
Code
Write code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3
Remote Control
Code
Write code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4
Remote Control
Code
Write code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5
Remote Control
Code
Write code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6
Remote Control
Code
Write code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7
Remote Control
Code
Read Status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x48 0xA1
Over Scan Write OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x00 0x90
Over Scan Write Value 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x01 0x91
Over Scan Write Value 2 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x02 0x92
Over Scan Write Value 3 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x03 0x93
Over Scan Write Value 4 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x04 0x94
Over Scan Write Value 5 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x05 0x95
Over Scan Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x33 0x91
Remote Key Write Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61
Remote Key Write Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65
Remote Key Write Top 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D
Remote Key Write Bottom 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E
Remote Key Write Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F
Remote Key Write Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60
Remote Key Write Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56
Remote Key Write Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67
Remote Key Write Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x08 0x5A
Operating
temperature
Read Get Value 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x03 0x65
Lamp mode cycle Write Lamp mode
cycle
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x36 0x00 0x95
This section describes the standard glossary of terms used in projector models. All
terms are listed in alphabetical order.
Some terms may not be applicable to your projector.
Refers to the ratio of the image width to the image height.
Built-in intelligent auto adjustment function that will re-adjust the
frequency and clock values to provide the best picture quality.
Temporarily hide the screen image to maintain audience focus when
necessary.
Maximizes the brightness of the projected image. This mode is ideal for
environments where extra-high brightness is required, such as using the
projector in well lit rooms.
Adjusts brightness levels of the screen image.
Synchronizes power on/off operation via HDMI connection. That is, if a
device that also supports CEC function is connected to the HDMI input of
the projector, when the projector’s power is turned off, the power of the
connected device will also be turned off automatically. When the power of
the connected device is turned on, the projector’s power will be turned on
automatically.
Adjusts the color saturation.
The projector is preset with several predefined color modes to suit
operating, environmental, and input source needs.
Adjusts the shape and size of an image that is unevenly rectangular on all
sides.
Allows users to select specific color temperature settings to further
customize their viewing experience.
8000K
Images appear bluish white.
6500K
Default color temperature. Images maintain a normal
white appearance. Recommended for general use.
5500K
Images appear reddish white.
Adjusts the difference between the image background (black level) and the
foreground (white level).
Manually improve the clarity of the projected image.
Allows the user to manually select the greyscale curve of the projector.
Allows the user to select HDMI greyscale range between 0~255 (Enhanced
Range) , 16~235 (Normal Range) or Auto by the signal type detected.
Optional mode for users who live in an environment between 1,500 m and
3,000 m above sea level, and the temperature is between 5° C and 25° C.
Activating it will improve projector cooling and performance.
Displays the timing mode (video signal input), the projector model number,
the serial number, and the ViewSonic® website URL.
Toggles between the various input options that are available for the
projector.
The distortion of an image caused by projecting it onto an angled surface. It
can be adjusted vertically via the
The projector’s lamp information and settings can be viewed and adjusted
by viewing the “Lamp Hours Information” or adjusting the “Lamp Mode”.
A Color Mode appropriate for playing colorful movies, video clips
from digital cameras, or DVs through the PC input. Best for a low light
environment.
Refers to a cropped image on your monitor’s screen. A setting on your
monitor zooms in on movie content, so that you cannot see the outermost
edges of the film.
Projects a grid to be used for image adjustment and fine-tuning.
The projected image can be adjusted based on the installation location of
the projector, i.e. ceiling or rear projection installation.
A standard code for serial communication transmission of data, used for
connection to other devices or controller vis serial port or LAN port.
Adjusts the picture quality.
A Color Mode that is designed for normal viewing circumstances in a
daylight environment.
Manually adjust the size of the projected image.
This section describes some common problems that you may experience when
using the projector.
The projector does not turn on • Ensure the power cord is properly aached to the
projector and to the power outlet.
• If the cooling process has not completed, please
wait unl it has nished then try to turn on the
projector again.
• If the above does not work, try another power outlet
or another electrical device with the same power
outlet.
There is no picture • Ensure the video source cable is connected properly,
and that the video source is turned on.
• If the input source is not selected automacally,
select the correct source with the key on
either the projector or the remote control.
The image is blurred • Adjusng the will help correctly focus the
projecon lens.
• Ensure the projector and screen are aligned properly.
If necessary, adjust the height of the projector as
well as the projecon angle and direcon.
The remote control does not
work
• Ensure there are no obstacles between the remote
control and projector; and that they are within 8 m
(26 ) of each other.
• The baeries may be out of power, please check and
replace if necessary.
Green
Flashing
Off Off Stand-by mode
Green Off Off Powering up
Green Off Off Normal operation
Green
Flashing
Off Off Normal power-down cooling
Red Off Off Downloading
Green Green Green Burn in off
Green
Flashing
Off Red First light source-lit error cooling
Off Off Red Light source error in normal operation
Green Off Red Color wheel start has failed
Off Red Off Fan 1 error (actual fan speed is outside the desired speed).
Off Red Red Fan 2 error (actual fan speed is outside the desired speed).
Off Red Green Fan 3 error (actual fan speed is outside the desired speed).
Off Red Orange Fan 4 error (actual fan speed is outside the desired speed).
Red
Flashing
Red Off Fan 5 error (actual fan speed is outside the desired speed).
Red
Flashing
Red
Flashing
Off Fan 6 error (actual fan speed is outside the desired speed).
Red Red Red Thermal sensor 1 open error (the remote diode has an
open-circuit condition).
Red Red Green Thermal sensor 2 open error (the remote diode has an
open-circuit condition).
Green Red Red Thermal sensor 1 short error (the remote diode has an
open-circuit condition).
Off Red Green Thermal sensor 2 short error (the remote diode has an
open-circuit condition).
Orange Red Red Temperature 1 error (over limited temperature).
Orange Red Green Temperature 2 error (over limited temperature).
Off Green Red Fan IC #1 I2C connection error.
• Make sure the Projector is turned o and the power cable is unplugged from the
power outlet.
• Never remove any parts from the Projector. Contact ViewSonic® or a reseller
when any part of the Projector needs replacing.
• Never spray or pour any liquid directly onto the case.
• Handle the Projector with care, as a darker-colored projector, if scued, may
show marks more clearly than a lighter-colored projector.
• Use a canister of compressed air to remove dust.
• If the lens is sll not clean, use lens-cleaning paper or moisten a so cloth with
lens cleaner and gently wipe the surface.
Never rub the lens with abrasive materials.
• Use a so, lint-free, dry cloth to remove dirt or dust.
• If the case is sll not clean, apply a small amount of non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, so, lint-free cloth, then wipe
the surface.
Never use wax, alcohol, benzene, thinner, or other chemical detergents.
If you intend to store the Projector for an extended period of time:
• Ensure the temperature and humidity of the storage area are within the
recommend range.
• Retract the adjuster foot completely.
• Remove the baeries from the Remote Control.
• Pack the Projector in its original packaging or equivalent.
• ViewSonic® does not recommend the use of any ammonia or alcohol-based
cleaners on the lens or case. Some chemical cleaners have been reported to
damage the lens and/or case of the projector.
• ViewSonic® will not be liable for damage resulng from use of any ammonia or
alcohol-based cleaners.
This section will provided a better understanding of your projector’s lamp.
When the projector is being used, the duration (in hours) of lamp usage is
automatically calculated by the built-in timer.
To obtain the lamp hour information:
Press to open the OSD Menu and go to:
Press and the page will appear:
Press to leave the menu.
To prolong lamp life, you can adjust the following settings in the OSD Menu.
Setting the projector in or mode reduces system
noise, power consumption, and extends the lamps operational life.
Provides full lamp brightness.
Reduces lamp power consumpon by 30% and lowers brightness,
and decreases fan noise.
Reduces lamp power consumpon by up to 65% depending on the
content's brightness level.
Reduces lamp power consumpon by 60% and lowers brightness to
extend the lamp life and decreases the fan noise.
To set the Lamp Mode, open the OSD Menu and go to:
and press / to select and press .
This allows the projector to turn off automatically after a set period of time once no
input source is detected.
Open the OSD Menu and go to:
and press / to disable or adjust the time.
When the lights up, please install a new lamp or consult your
dealer.
An old lamp may cause a malfuncon in the projector and in some
instances the lamp may explode.
It is recommended to turn the power off and disconnect the projector from the
power outlet, and contact a qualified service personnel for lamp replacement.
This section addresses all connected requirements and statements regarding
regulations. Confirmed corresponding applications shall refer to nameplate labels
and relevant markings on the unit.
This device complies with part 15 of FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You are cauoned that changes or modicaons not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
CAN ICES-3 (B)/NMB-3(B)
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
The mark shown to the right is in compliance with the Waste Electrical
and Electronic Equipment Directive 2012/19/EU (WEEE). The mark
indicates the requirement NOT to dispose of the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Cadmium (Cd) 0.01% < 0.01%
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl esthers (PBDE) 0.1% < 0.1%
Bis(2-Ethylhexyl) phthalate (DEHP) 0.1% < 0.1%
Benzyl butyl phthalate (BBP) 0.1% < 0.1%
Dibutyl phthalate (DBP) 0.1% < 0.1%
Diisobutyl phthalate (DIBP) 0.1% < 0.1%
• Mercury in cold cathode fluorescent lamps and external electrode fluorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
»Short length (500 mm): maximum 3.5 mg per lamp.
»Medium length (> 500 mm and 1,500 mm): maximum 5 mg per lamp.
»Long length (> 1,500 mm): maximum 13 mg per lamp.
• Lead in glass of cathode ray tubes.
• Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
• Lead as an alloying element in aluminum containing up to 0.4% lead by weight.
• Copper alloy containing up to 4% lead by weight.
• Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
• Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
Restriction on Hazardous Substances statement (India). This product complies
with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for
the exemptions set in Schedule 2 of the Rule.
ViewSonic® respects the environment and is committed to working and living
green. Thank you for being part of Smarter, Greener Computing. Please visit the
ViewSonic® website to learn more.
http://www.viewsonic.com/company/green/recycle-program/
http://www.viewsoniceurope.com/uk/support/recycling-information/
Copyright© ViewSonic® Corporation, 2019. All rights reserved.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic® and the three birds logo are registered trademarks of ViewSonic®
Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
ViewSonic® Corporation shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential damages
resulting from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation
reserves the right to change product specifications without notice. Information in
this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any
means, for any purpose without prior written permission from ViewSonic®
Corporation.
PX727HD_UG_ENG_1a_20190819
For technical support or product service, see the table below or contact your
reseller.
You will need the product’s serial number.
Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/
中国 (China) www.viewsonic.com.cn 香港 (繁體中文) www.viewsonic.com/hk/
Hong Kong (English) www.viewsonic.com/hk-en/ India www.viewsonic.com/in/
Indonesia www.viewsonic.com/id/ Israel www.viewsonic.com/il/
日本 (Japan) www.viewsonic.com/jp/ Korea www.viewsonic.com/kr/
Malaysia www.viewsonic.com/my/ Middle East www.viewsonic.com/me/
Myanmar www.viewsonic.com/mm/ Nepal www.viewsonic.com/np/
New Zealand www.viewsonic.com/nz/ Pakistan www.viewsonic.com/pk/
Philippines www.viewsonic.com/ph/ Singapore www.viewsonic.com/sg/
臺灣 (Taiwan) www.viewsonic.com/tw/ ประเทศไทย www.viewsonic.com/th/
Việt Nam www.viewsonic.com/vn/ South Africa &
Maurius www.viewsonic.com/za/
United States www.viewsonic.com/us Canada www.viewsonic.com/us
Lan America www.viewsonic.com/la
Europe www.viewsonic.com/eu/ France www.viewsonic.com/fr/
Deutschland www.viewsonic.com/de/ Қазақстан www.viewsonic.com/kz/
Россия www.viewsonic.com/ru/ España www.viewsonic.com/es/
Türkiye www.viewsonic.com/tr/ Україна www.viewsonic.com/ua/
United Kingdom www.viewsonic.com/uk/
ViewSonic® Projector
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product
proves to be defective in material or workmanship during the warranty period,
ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or
components.
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
for labor, and one (1) year for the original lamp from the date of the first consumer
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
office for the warranty information.
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
original lamp from the date of the first consumer purchase; Europe: One (1) year
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90)
days for the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
office for the warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies
to manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
This warranty is valid only for the first consumer purchaser.
1. Any product on which the serial number has been defaced, modied or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a. Accident, abuse, misuse, neglect, re, water, lightning, or other acts of nature,
improper maintenance, unauthorized product modicaon, or failure to follow
instrucons supplied with the product.
b. Operaon outside of product specicaons.
c. Operaon of the product for other than the normal intended use or not under
normal condions.
d. Repair or aempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installaon of the product.
g. Causes external to the product, such as electric power uctuaons or failure.
h. Use of supplies or parts not meeng ViewSonic’s specicaons.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
1. For informaon about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original
dated sales slip, (b) your name, (c) your address, (d) a description of the problem,
and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
There are no warranties, express or implied, which extend beyond the description
contained herein including the implied warranty of merchantability and fitness for
a particular purpose.
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of me, loss of prots, loss of
business opportunity, loss of goodwill, interference with business relaonships,
or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
This warranty gives you specific legal rights, and you may also have other rights
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
ViewSonic® Projector
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product
proves to be defective in material or workmanship during the warranty period,
ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or
components & accessories.
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original
lamp from the date of the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies
to manufacturer’s installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
This warranty is valid only for the first consumer purchaser.
1. Any product on which the serial number has been defaced, modied or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, re, water, lightning, or other acts of nature,
unauthorized product modicaon, unauthorized aempted repair, or failure to
follow instrucons supplied with the product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power uctuaons or failure.
d. Use of supplies or parts not meeng ViewSonic’s specicaons.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which
results when a static image is displayed on the product for an extended period of
time.
4. Removal, installation, insurance, and set-up service charges.
For information about receiving service under warranty, contact ViewSonic
Customer Support (Please refer to the attached Customer Support page). You
will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use.
Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1. To obtain warranty service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a descripon of the problem, and
(e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized
ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by
ViewSonic.
There are no warranties, express or implied, which extend beyond the description
contained herein including the implied warranty of merchantability and fitness for
a particular purpose.
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of me, loss of prots, loss of
business opportunity, loss of goodwill, interference with business relaonships,
or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Contact Informaon for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporavo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 hp://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garanzados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
Tel: 800-688-6688
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
C0 M91 Y72 K24
Process Color
C0 M0 Y0 K100
Process Color
C0 M91 Y72 K24
Process Color
Pantone Black C
Spot Color
Pantone 187 C
Spot Color
Pantone Black C
Spot Color
Pantone 187 C
Or Spot Color