Table of Contents
- PX727-4K_PX747-4K_en.pdf
- Table of contents
- Important safety instructions
- Introduction
- Positioning your projector
- Connection
- Operation
- Starting up the projector
- Using the menus
- Utilizing the password function
- Switching input signal
- Adjusting the projected image
- Selecting the aspect ratio
- Optimizing the image
- Hiding the image
- Locking control keys
- Operating in a high altitude environment
- Adjusting the sound
- Shutting down the projector
- Menu operation
- Maintenance
- Troubleshooting
- Specifications
- Copyright information
Viewsonic PX747-4K User Manual
Displayed below is the user manual for PX747-4K by Viewsonic which is a product in the Data Projectors category. This manual has pages.
Related Manuals
PX727-4K/PX747-4K
DLP Projector
User Guide
Model No. VS17154/VS17290
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
ZZZYLHZVRQLFFRP LQ(QJOLVKRULQ VSHFL¿FODQJXDJHV XVLQJWKH 5HJLRQDOVHOHFWLRQ
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
i
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the follow-
ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHG
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
ii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXU
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKH
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
iii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGHÀXRUHVFHQW
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
iv
Copyright Information
Copyright © ViewSonic® Corporation, 2018. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFX-
ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name: PX727-4K/PX747-4K
ViewSonic DLP Projector
Model Number: VS17154/VS17290
Document Number: PX727-4K/PX747-4K_UG_ENG Rev. 1A 01-22-18
Serial Number: ________________________________________
Purchase Date: ________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
1
Table of contents
Important safety
instructions .......................2
Introduction......................5
Projector features ................................. 5
Shipping contents................................. 5
Controls and functions ......................... 6
Positioning your projector
..........................................11
Choosing a location............................ 11
Projection dimensions........................ 12
Connection ......................14
Connecting a computer or monitor .... 15
Connecting Video source devices ...... 15
Operation ........................16
Starting up the projector..................... 16
Using the menus................................. 17
Utilizing the password function ......... 18
Switching input signal........................ 20
Adjusting the projected image ........... 20
Selecting the aspect ratio ................... 21
Optimizing the image......................... 22
Hiding the image................................ 25
Locking control keys.......................... 26
Operating in a high altitude
environment ....................................... 26
Adjusting the sound ........................... 26
Shutting down the projector............... 27
Menu operation .................................. 28
Maintenance ...................36
Care of the projector .......................... 36
Lamp information.............................. 36
Troubleshooting .............39
Specifications ..................40
Dimensions ........................................ 40
Ceiling mount installation ................. 40
IR control table .................................. 41
RS232 command table....................... 42
Timing chart ...................................... 48
Projector specifications...................... 50
Copyright information...51
2
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1. Please read this manual before you operate your projector. Save it for future
reference.
2. Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3. Refer servicing to qualified service personnel.
4. Always open the lens shutter or remove the lens cap when the projector lamp is
on.
5. In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
6. Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
7. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
9. Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
3
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
21. CAUTION
Possibly hazardous optical radiation emitted from
this product. Do not stare at operating lamp. May be
harmful to the eyes. Risk Group 2. As with any bright
light source, do not stare into the beam, RG2 IEC 62471-5:201
Warning
• THIS APPARATUS MUST BE EARTHED.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed
wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a
fault should occur during operation of the unit, operate the disconnect device to switch
the power supply off, or disconnect the power plug.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommend that you also purchase a separate security cable and attach it securely to
both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This
4
will perform the secondary role of restraining the projector should its attachment to the
mounting bracket become loose.
5
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
Some of the features may not be available on your projector. Actual performance may vary
and subject to model specifications.
• Power saving function decreasing the power consumption of the lamp by up to 70%
when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
•Color Management allowing color adjustments to your liking
• Less than 0.5W power consumption when power saving mode is turned on
• Quick auto search speeding up the signal detecting process
• Color modes providing choices for different projection purposes
• One-key auto-adjustment to display the best picture quality (only for analog signal)
• Digital keystone correction to correct distorted images
• Adjustable color management control for data/video display
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is directly proportional to
projection distance.
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Shipping contents
1. Projector 2. VGA Cable (for selected models)
3. Power Cord 4. Quick Start Guide 5. Remote Control & Batteries
6. Replacement lamp (optional) (Please contact qualified service personnel for changing the
lamp)
6
Controls and functions
Projector
•Power
Toggles the projector between standby
mode and Power ON.
•/ (Keystone keys)
Manually corrects distorted images
resulting from an angled projection.
• Left/ Right/ Up/ Down
Selects the desired menu items and makes
adjustments when the On-Screen Display
(OSD) menu is activated.
• Menu/Exit
Turns on or off the On-Screen Display
(OSD) menu.
• Source
Displays the source selection bar.
•Blank
Hides the screen picture.
•Enter
Enacts the selected On-Screen Display
(OSD) menu item when the On-Screen
Display (OSD) menu is activated.
• (Volume Up)
Increases the volume level.
• (Volume Down)
Decreases the volume level.
Focus ring
Power indicator light
Lamp indicator lightTemperature indicator
light
Zoom ring
Projection lens
Vent (heated air exhaust)
7
1. AUDIO IN
Audio signal input socket.
2. AUDIO OUT
Audio signal output socket.
3. COMPUTER IN
RGB (PC) signal input socket.
4. HDMI 1
HDMI (HDCP2.2) port.
5. HDMI 2
HDMI port.
6. MINI USB
Mini USB port (for service only).
7. RS-232
RS-232 control port.
8. USB 5V/1.5A Out
USB Type A port for power supply.
9. 12V OUT
12V DC output terminal.
12 3 4 5 6 7 8 9
Security bar for anti-theft lock slot
Kensington anti-theft lock slot
AC power cord inlet
Ceiling mount holes
Adjuster foot
Adjuster foot
8
Remote control
•On/Off
Toggles the projector between standby
mode and Power ON.
•COMP
Selects source from COMPUTER IN
port for display.
•HDMI 1
Selects source from HDMI 1 port for
display.
•HDMI 2
Selects source from HDMI 2 port for
display.
• Auto Sync
Automatically determines the best
picture timings for the displayed
image.
• Source
Displays the source selection bar.
• / (Keystone keys)
Manually corrects distorted images
resulting from an angled projection.
•Enter
Enacts the selected On-Screen Display
(OSD) menu item.
• Left/ Right/ Up/ Down
Selects the desired menu items and
makes adjustments.
•Menu
Turns on or off the On-Screen Display
(OSD) menu.
• (Information)
Displays the INFORMATION menu.
•Exit
Goes back to previous OSD menu,
exits and saves menu settings.
9
Remote control effective range
Refer to the illustration about the location of the Infra-
Red (IR) remote control sensor(s). The remote control
must be held at an angle within 30 degrees
perpendicular to the projector's IR remote control
sensor(s) to function correctly. The distance between
the remote control and the sensor(s) should not exceed
8 meters (~ 26 feet).
Make sure that there are no obstacles between the
remote control and the IR sensor(s) on the projector
that might obstruct the infra-red beam.
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, press on the
finger grip on the cover and slide it down in the direction of the arrow as illustrated.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
• Aspect
Displays the aspect ratio selection bar.
• Pattern
Displays embedded test pattern.
•Blank
Hides the screen picture.
•HDR
Displays the HDR menu.
• (Volume Up)
Increases the volume level.
• (Volume Down)
Decreases the volume level.
• (Mute)
Toggles the projector audio between on and
off.
• Brightness
Displays the brightness adjustment bar.
•Silence
Activates the Silence mode. It takes a few
seconds to take effect.
•Eco Mode
Selects the Eco mode.
• Contrast
Displays the contrast adjustment bar.
•Standard
Selects the Standard mode.
•Movie
Selects the Movie mode.
•Color Temp
Displays the color temperature menu.
• User1
Selects the User 1 mode.
• User2
Selects the User 2 mode.
Approx. 30°
Approx. 30°
10
3. Refit the cover by aligning it with the base and pushing it back down into position.
Stop when it clicks into place.
WARNING
• Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are drained or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
11
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of the following possible installation
locations:
1. Front
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2. Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the INSTALLATION >
Projector Mode menu after you turn the projector
on.
3. Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the INSTALLATION >
Projector Mode menu after you turn the projector
on.
4. Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the INSTALLATION >
Projector Mode menu after you turn the projector
on.
12
Projection dimensions
The "screen" mentioned below refers to the projection screen usually consisting of a screen
surface and a support structure.
Please see "Projector specifications" on page 50 for the native display resolution of this
projector.
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(a)
(c)
(b)
(e)
(f)
(d)
(f): Center of lens(e): Screen
• 16:9 image on a 16:9 screen
• 16:9 image on a 4:3 screen
(a)
(d)
(c)
(b)
(e)
(f)
(a) Screen Size
16:9 image on a 16:9 Screen
(b) Projection distance (c) Image
height
(d) Vertical offset
min. max. min. max.
inch mm inch mm inch mm inch mm inch mm inch mm
60 1524 77 1952 92 2342 29 747 2.9 75 2.9 75
70 1778 90 2277 108 2732 34 872 3.4 87 3.4 87
80 2032 102 2602 123 3123 39 996 3.9 100 3.9 100
90 2286 115 2927 138 3513 44 1121 4.4 112 4.4 112
100 2540 128 3253 154 3903 49 1245 4.9 125 4.9 125
110 2794 141 3578 169 4293 54 1370 5.4 137 5.4 137
120 3048 154 3903 184 4684 59 1494 5.9 149 5.9 149
130 3302 166 4228 200 5074 64 1619 6.4 162 6.4 162
140 3556 179 4554 215 5464 69 1743 6.9 174 6.9 174
150 3810 192 4879 231 5855 74 1868 7.4 187 7.4 187
160 4064 205 5204 246 6245 78 1992 7.8 199 7.8 199
170 4318 218 5529 261 6635 83 2117 8.3 212 8.3 212
180 4572 231 5855 277 7026 88 2241 8.8 224 8.8 224
190 4826 243 6180 292 7416 93 2366 9.3 237 9.3 237
200 5080 256 6505 307 7806 98 2491 9.8 249 9.8 249
13
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
(a) Screen Size
16:9 image on a 4:3 Screen
(b) Projection distance (c) Image
height
(d) Vertical offset
min. max. min. max.
inch mm inch mm inch mm inch mm inch mm inch mm
60 1524 71 1791 85 2150 27 686 2.7 69 2.7 69
70 1778 82 2090 95 2421 32 800 3.2 80 3.2 80
80 2032 94 2388 109 2767 36 914 3.6 91 3.6 91
90 2286 106 2687 123 3113 41 1029 4.1 103 4.1 103
100 2540 118 2986 136 3459 45 1143 4.5 114 4.5 114
110 2794 129 3284 150 3805 50 1257 5.0 126 5.0 126
120 3048 141 3583 163 4151 54 1372 5.4 137 5.4 137
130 3302 153 3881 177 4497 59 1486 5.9 149 5.9 149
140 3556 165 4180 191 4843 63 1600 6.3 160 6.3 160
150 3810 176 4478 204 5189 68 1715 6.8 171 6.8 171
160 4064 188 4777 218 5535 72 1829 7.2 183 7.2 183
170 4318 200 5075 232 5881 77 1943 7.7 194 7.7 194
180 4572 212 5374 245 6226 81 2057 8.1 206 8.1 206
190 4826 223 5672 259 6571 86 2172 8.6 217 8.6 217
200 5080 235 5971 272 6916 90 2286 9.0 229 9.0 229
14
Connection
When connecting a signal source to the projector, be sure to:
1. Turn all equipment off before making any connections.
2. Use the correct signal cables for each source.
3. Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
The connection illustrations below are for reference only. The connecting jacks available on
the projector vary with each projector model.
For detailed connection methods, see pages 15.
15
Connecting a computer or monitor
Connecting a computer
1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2. Connect the other end of the VGA cable to the COMPUTER IN signal input socket
on the projector.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting Video source devices
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
1. Take an HDMI cable and connect one end to the HDMI output port of the video
device.
2. Connect the other end of the cable to the HDMI 1 (supports DHCP 2.2) or HDMI 2
input port on the projector.
In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI
input and the projected picture displays wrong colors, please change the color space to YUV.
See "Changing HDMI input settings" on page 20 for details.
Connecting audio
You can make use of the projector speaker in your presentations, and also connect separate
amplified speakers to the AUDIO OUT socket of the projector. The audio output is
controlled by the projector Volume and Mute settings.
16
Operation
Starting up the projector
1. Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted).
2. Press Power to start the projector. As soon as
the lamp lights up, a "Power On Ring Tone" will
be heard. The Power indicator light stays blue
when the projector is on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning
it off.
3. If the projector is activated for the first time, select your OSD language following the
on-screen instructions. After Reset All Settings is performed, the next time you turn
on the projector, you need to select your OSD language first.
4. Switch all of the connected equipment on.
5. The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the source selection bar displays. If the projector still doesn’t detect a
valid signal for a few minutes, the message 'No Signal' will be displayed until an input
signal is found.
You can also press Source to select your desired input signal. See "Switching input
signal" on page 20 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 48 for details.
17
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please select your language first.
1. Press Menu to turn the OSD menu
on.
3. Press to highlight Language and
press Enter.
2. Use / to highlight the
SYSTEM SETUP: BASIC menu.
4. Use / / / to select a
preferred language.
5. Press Enter to go back to main
menu and press Menu to leave the
OSD menu.
Current input signal
Main menu icon
Sub-menu
Highlight
Go to the
previous page
or to exit.
Status
Picture Mode
PICTURE
User Mode Settings
Brightness
Contrast
Color
Tint
Sharpness
Advanced
Reset Current Picture Mode
Movie
PC Exit
Picture Mode
PICTURE
User Mode Settings
Brightness
Contrast
Color
Tint
Sharpness
Advanced
Reset Current Picture Mode
Movie
PC Exit
Language
SYSTEM SETUP: BASIC
Background Color
Brightness
Splash Screen
Auto Power Off
Direct Power On
Menu Settings
Rename Input
Auto Input Search
PC Exit
Language
SYSTEM SETUP: BASIC
Background Color
Brightness
Splash Screen
Auto Power Off
Direct Power On
Menu Settings
Rename Input
Auto Input Search
PC Exit
18
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 17.
You will be inconvenienced if you enable the password function yet forget the password
somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Setting a password
Once a password has been set and the power on lock is enabled, the projector cannot be used
unless the correct password is entered every time the projector is started.
1. Open the OSD menu and go to the SYSTEM SETUP: ADVANCED > Password
menu.
2. Press Enter and the Password page is displayed.
3. Highlight Power On Lock and select On by pressing /.
4. As pictured to the right, the four arrow keys
( , , , ) respectively represent 4
digits (1, 2, 3, 4). According to the password
you desire to set, press the arrow keys to
enter six digits for the password.
5. Confirm the new password by re-entering
the new password.
Once the password is set, the OSD menu
returns to the Password page.
6. To leave the OSD menu, press Exit.
If you forget the password
If the password function is activated, you will be
asked to enter the six-digit password every time you
turn on the projector. If you enter the wrong
password, the password error message as pictured
to the right is displayed lasting for 5 seconds, and
the message 'INPUT PASSWORD' follows. You
can retry by entering another six-digit password, or
if you did not record the password in this user manual, and you absolutely do not remember
it, you can use the password recall procedure. See "Entering the password recall procedure"
on page 19 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
INPUT NEW PASSWORD
Exit
Password Error
Please try again
19
Entering the password recall procedure
1. When the message 'INPUT CURRENT
PASSWORD' is displayed, press and hold
Enter for 3 seconds. The projector will
display a coded number on the screen.
2. Write down the number and turn off your
projector.
3. Seek help from the local service center to
decode the number. You may be required to
provide proof of purchase documentation to
verify that you are an authorized user of the projector.
The "XXX" shown in the above screenshot are numbers that vary depending on different
projector models.
Changing the password
1. Open the OSD menu and go to the SYSTEM SETUP: ADVANCED > Password >
Change Password menu.
2. Press Enter. The message 'INPUT CURRENT PASSWORD' is displayed.
3. Enter the old password.
• If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
• If the password is incorrect, the password error message is displayed lasting for
5 seconds, and the message 'INPUT CURRENT PASSWORD' is displayed
for your retry. You can press Exit to cancel or try another password.
4. Enter a new password.
5. Confirm the new password by re-entering the new password.
6. You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7. To leave the OSD menu, press Exit.
The digits being input will be displayed as asterisks on-screen. Do make a note of your
password, and then keep the note in a safe place for later recall.
Disabling the password function
1. Open the OSD menu and go to the SYSTEM SETUP: ADVANCED > Password >
Power On Lock menu.
2. Press / to select Off.
3. The message 'INPUT PASSWORD' is displayed. Enter the current password.
• If the password is correct, the OSD menu returns to the Password page with
'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
• If the password is incorrect, the password error message is displayed lasting for
5 seconds, and the message 'INPUT PASSWORD' is displayed for your retry.
You can press Exit to cancel or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
RECALL PASSWORD
Please write down the recall code,
and contact ViewSonic
Customer Center.
Recall Code:
Exit
20
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Auto Input Search function in the SYSTEM SETUP: BASIC menu is On if
you want the projector to automatically search for the signals.
You can also manually select the desired signal by pressing one of the source selection keys
on the remote control, or cycle through the available input signals.
1. Press Source. A source selection bar is displayed.
2. Press / until your desired signal is selected and press Enter.
Once detected, the selected source information will be displayed on the screen for
seconds. If there are multiple devices connected to the projector, repeat steps 1-2 to
search for another signal.
Please see "Projector specifications" on page 50 for the native display resolution of this
projector. For best display picture results, you should select and use an input signal which
outputs at this resolution. Any other resolutions will be scaled by the projector depending
upon the 'aspect ratio' setting, which may cause some image distortion or loss of picture
clarity. See "Selecting the aspect ratio" on page 21 for details.
Changing HDMI input settings
In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray
player) via the projector’s HDMI input and the projected picture displays wrong colors,
please change the color space to an appropriate one that fits the color space setting of the
output device.
To do this:
1. Open the OSD menu and go to the SYSTEM SETUP: ADVANCED > HDMI
Range menu.
2. Press / to select a suitable color space according to the color space setting of the
output device connected.
•Auto: Sets the projector to detect the HDMI range of the input signal
automatically.
•Full Range: Sets the HDMI color range as 0 - 255.
•Limited Range: Sets the HDMI color range as 16 - 235.
This function is only available when the HDMI input port is in use.
Refer to the documentation of the device for information on the color space and HDMI range
settings.
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 2 adjuster feet. It changes the image height and vertical
projection angle. Screw the adjuster feet to fine tune the angle until the image is positioned
where you want it.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
21
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press Auto Sync on
the remote control. Within 5 seconds, the built-in Intelligent Auto Adjustment function will
re-adjust the values of Frequency and Clock to provide the best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
This function is only available when PC D-Sub input signal (analog RGB) is selected.
It is recommended that you display a bright image when performing this function.
Fine-tuning the image clarity
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To select an image ratio that suits your need (no matter what aspect the source is), you can
follow one of the following steps.
• Press Aspect repeatedly.
•Go to the DISPLAY > Aspect Ratio menu and press Enter. Press / to select an
aspect ratio to suit the format of the video signal and your display requirements.
About the aspect ratio
1. Auto: Scales an image proportionally to fit the projector's native resolution in its
horizontal width. This is suitable for the incoming image which is neither in 4:3 nor
16:9 and you want to make most use of the screen without altering the image's aspect
ratio.
2. 4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect
ratio. This is most suitable for 4:3 images like computer monitors, standard definition
TV and 4:3 aspect DVD movies, as it displays them without aspect alteration.
3. 16:9: Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio. This is most suitable for images which are already in a 16:9 aspect, like
high definition TV, as it displays them without aspect alteration.
4. 2.35:1: Scales an image so that it is displayed in the center of the screen with a 2.35:1
aspect ratio. This is most suitable for images which are already in a 2.35:1 aspect, as it
displays them without aspect alteration.
1. Adjust the projected image to the size
that you need using the zoom ring.
2. If necessary, sharpen the image by rotating
the focus ring.
22
The table below demonstrates the effects of the aspect ratio settings on projectors with
different native resolutions. Please see "Projector specifications" on page 50 for the native
display resolution of your projector.
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
Optimizing the image
Selecting a picture mode
The picture mode cannot be adjusted when the DISPLAY > Silence menu is set at On.
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
•Press the picture mode selection buttons on the remote control.
•Go to the PICTURE > Picture Mode menu and press / to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
1. Bright mode: Maximizes the brightness of the projected image. This mode is suitable
for environments where extra-high brightness is required, such as using the projector
in well lit rooms.
2. Standard mode: Is designed for normal circumstances under daylight environment.
3. Movie mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
4. User 1/User 2: Recalls the customized settings. After User 1/User 2 is selected, some
of the sub-menus under the PICTURE menu can be adjusted, according to your
selected input signal.
Aspect ratio setting When the native aspect ratio of your projector is...
4:3 16:9 16:10
Auto
4:3
16:9 Not available
2.35:1
23
5. Silence mode: Minimizes the acoustic noise. It is suitable for the need of watching
movies that requires an ultra-quiet environment so that you won't be disturbed by the
noise of the projector. This mode is automatically selected when the DISPLAY >
Silence menu is set at On, and you cannot switch the picture mode. When this mode
is selected, XPR will be off (the projected image will be switched to 1080p resolution
automatically), Light Source Mode will switch to Eco and some functions may not
be available.
The selected Silence mode remains active when you switch the input signal.
There are 2 user-definable modes if the current available picture modes are not suitable for
your need. You can use one of the picture modes as a starting point and customize the
settings.
1. Go to the PICTURE > Picture Mode menu and press / to select User 1 or User
2.
2. Go to the PICTURE > User Mode Settings > Load Settings menu, and select a
picture mode that is closest to your need.
3. Adjust the menu item under PICTURE menu. The adjustments define the selected
user mode.
You can rename the picture mode by entering the PICTURE > User Mode Settings >
Rename User Mode menu. Use / / / to select the characters and Enter to
confirm. The settings will take effect immediately. Select Reset if you wish to reset the
parameters to the factory setting.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available.
You can make adjustments to these functions based on your needs.
Adjusting Brightness
Go to the PICTURE > Brightness menu and press Enter.
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
Adjusting Contrast
Go to the PICTURE > Contrast menu and press Enter.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
Adjusting Color
Go to the PICTURE > Color menu and press /.
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Go to the PICTURE > Tint menu and press /.
The higher the value, the more greenish the picture becomes. The lower the value, the more
reddish the picture becomes.
50
-30 +80
-30 0+40
24
Adjusting Sharpness
Go to the PICTURE > Sharpness menu and press /.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Selecting a gamma setting
Go to the PICTURE > Advanced > Select Gamma menu and select a preferred setting by
pressing /.
Gamma refers to the relationship between input source and picture brightness.
Selecting a Color Temperature
Go to the PICTURE > Advanced > Color Temperature menu and press /.
There are several preset color temperature settings available. The available settings may
vary according to the signal type selected.
•Cool: With the highest color temperature, Cool makes the image appear the most bluish
white than other settings.
•Normal: Maintains normal colorings for white.
•Warm: Makes images appear reddish white.
Setting a preferred color temperature
1. Go to the PICTURE > Color Temperature menu and press Enter.
2. Press / to select Cool, Normal or Warm and press Enter.
3. Press / to highlight the item you want to change and adjust the values by
pressing /.
•Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green,
and Blue.
•Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red,
Green, and Blue.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the 3D Color Management menu to make
adjustments.
To adjust the settings:
1. Go to the PICTURE > Advanced > 3D Color Management menu.
2. Press Enter and the 3D Color Management page is displayed.
3. Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
4. Press to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
25
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
5. Press to highlight Gain and adjust its
values to your preference by pressing /.
The contrast level of the primary color you
select will be affected. Every adjustment
made will reflect to the image immediately.
6. Press to highlight Saturation and adjust
its values to your preference by pressing /. Every adjustment made will reflect to
the image immediately.
For example, if you select Red and set its value at 0, only the saturation of pure red
will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
7. Repeat steps 3 to 7 for other color adjustments. Make sure you have made all of the
desired adjustments.
Using the MoviePro menu
Go to the PICTURE > Advanced > MoviePro menu and you can adjust the following
items.
•Color Enhancement: Allows you to fine-tune the saturation of colors with larger
flexibility. It modulates complex color algorithms to flawlessly render saturated colors,
fine gradients, intermediate hues and subtle pigments.
•Skin Tone: Provides a smart adjustment of hue only for calibrating people's skin color,
not other colors in the image. It prevents discoloration of skin tones from the light of the
projection beam, portraying every skin tone in its most beautiful shade.
•Super Resolution: It is a super-resolution technology which radically enhances Full
HD content in terms of colors and textures. It's also a detail enhancement technology
refines surface details for true-to-life images that pop off the screen. Users can adjust
levels of sharpness and detail enhancement for optimal viewing.
Hiding the image
In order to draw the audience's full attention to the presenter, you can press Blank on the
projector or remote control to hide the screen image. Press any key on the projector or
remote control to restore the image. The word 'BLANK' appears at the central bottom area
of the screen.
Once Blank is pressed, the projector consumes minimum power.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
RED
BLUE
GREEN
Yellow
Cyan
Magenta
26
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except Power.
1. Go to the SYSTEM SETUP: ADVANCED > Panel Key Lock menu
2. Press Enter and press / to select On.
3. A confirmation message is displayed. Select Yes to confirm.
To release panel key lock, press and hold on the projector for 3 seconds.
You can also use the remote control to enter the SYSTEM SETUP: ADVANCED > Panel
Key Lock menu and select Off.
Keys on the remote control are still functional when panel key lock is enabled.
If you press Power to turn off the projector without disabling panel key lock, the projector
will still be in locked status the next time it is turned on.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 5°C–25°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1499 m and temperature
is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
To activate the High Altitude Mode:
1. Open the OSD menu and go to the
INSTALLATION > High Altitude Mode
menu.
2. Press Enter and press / to select On.
A confirmation message is displayed.
3. Highlight Yes and press Enter.
Operation under "High Altitude Mode" may
cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. Be sure
you have made a correct connection to the projector audio input/output jacks. See
"Connection" on page 14 for more details.
Muting the sound
1. Open the OSD menu and go to the SYSTEM SETUP: ADVANCED > Audio
Settings > Mute menu.
Notice
We recommend you use the High
Altitude mode by selecting it when-
ever your environment is higher
than 1500m.
Do you want to turn High Altitude
Mode ON?
Yes No
27
2. Press / to select On.
Adjusting the sound level
1. Open the OSD menu and go to the SYSTEM SETUP: ADVANCED > Audio
Settings > Audio Volume menu.
2. Press / to select a desired sound level.
If available, you can press // on the remote control to adjust the projector’s sound
level.
Shutting down the projector
1. Press Power or Off and a confirmation
message is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
2. Press Power or Off a second time.
3. Once the cooling process finishes, a "Power
Off Ring Tone" will be heard. Disconnect the
power cord from the wall socket if the
projector will not be used in an extended
period of time.
To turn off the ring tone, see "Shutting down the projector" on page 27 for details.
CAUTION
• To protect the lamp, the projector will not respond to any commands during the cooling
process.
• Do not unplug the power cord before the projector shutdown sequence is complete.
28
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu Sub-menu Options
PICTURE
Picture Mode Bright/Standard/Movie/User 1/
User 2/(Silence)
User Mode
Settings
Load Settings Bright/Standard/Movie/User 1/
User 2
Rename User Mode
Brightness
Contrast
Color
Tint
Sharpness
Advanced
Select Gamma 1.8/2.0/2.2/2.3/2.4/2.5/2.6/2.8/
Custom 1/Custom 2
Color
Temperature
Preset
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
3D Color
Management
Primary Color
Hue
Gain
Saturation
MoviePro
Color Enhancement
Skin Tone
Super Resolution
Reset Current Picture Mode Reset/Cancel
29
Main menu Sub-menu Options
DISPLAY
Aspect Ratio Auto/4:3/16:9/2.35:1
Image Position
OverScan Adjustment 0/1/2/3
Phase
H. Size
Silence Off/On
INSTALLATION
Projector Mode Front/Rear/Rear Ceiling/Front
Ceiling
Test Pattern Off/On
Light Source
Settings
Light Source
Mode Normal/Eco/Dynamic
Reset Light
Timer Reset/Cancel
Light Source
Information
Light Source Usage Time
Normal
Eco
Dynamic
Equivalent Lamp Hour
12V Trigger Off/On
High Altitude Mode Off/On
SYSTEM
SETUP: BASIC
Language Multi-language OSD selection
Background Color Green/Black/Blue
Splash Screen ViewSonic/Black/Blue
Auto Power Off Disable/5 min/10 min/15 min/20
min/25 min/30 min
Direct Power On Off/On
Menu
Settings
Menu Position Center/Top-Left/Top-Right/
Bottom-Right/Bottom-Left
Menu Display
Time
Always On/5 sec/10 sec/15 sec/
20 sec/25 sec/30 sec
Reminder
Message Off/On
Rename Input
Auto Input Search Off/On
30
Main menu Sub-menu Options
SYSTEM
SETUP:
ADVANCED
HDR HDR Auto/SDR
EOTF Low/Mid/High
Audio Settings Audio Volume
Mute On/Off
HDMI Range Auto/Full Range/Limited
Range
Password Change Password
Power On Lock Off/On
Panel Key Lock Off/On
Reset All Settings Reset/Cancel
Information
•Input
•Picture Mode
•Resolution
•Color System
•Light Source Usage Time
• Firmware Version
31
Description of each menu
Function Description
Picture Mode
See "Selecting a picture mode" on page 22 for details.
User Mode
Settings
Brightness See "Adjusting Brightness" on page 23 for details.
Contrast See "Adjusting Contrast" on page 23 for details.
Color See "Adjusting Color" on page 23 for details.
Tint See "Adjusting Tint" on page 23 for details.
Sharpness See "Adjusting Sharpness" on page 24 for details.
Advanced
Select Gamma
See "Selecting a gamma setting" on page 24 for details.
Color Temperature
See "Selecting a Color Temperature" on page 24 and "Setting a
preferred color temperature" on page 24 for details.
3D Color Management
See "Color Management" on page 24 for details.
Reset Current
Picture Mode Returns current picture settings to the factory preset values.
PICTURE menu
32
Function Description
Aspect Ratio See "Selecting the aspect ratio" on page 21 for details.
Image Position
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you
made until they reach their maximum or minimum.
This function is only available when a PC input signal is
selected.
The adjustment range may vary under different timings.
OverScan
Adjustment Adjusts the overscan rate from 0 to 3.
Phase
Adjusts the clock phase to reduce image
distortion.
This function is only available
when PC D-Sub input signal (analog RGB) is selected.
H. Size
Adjusts the horizontal width of the image.
This function is only available when a PC input signal
(analog RGB) is selected.
Silence
When this function is enabled:
• The acoustic noise will be minimized.
• XPR will be off (the projected image will be switched to
1080p resolution automatically).
•Light Source Mode will switch to Eco.
• Some functions may not be available.
•Picture Mode will be fixed at Silence automatically. See
"Selecting a picture mode" on page 22 for details.
• This function will be de-activated the next turn you turn on
the projector.
DISPLAY menu
33
Function Description
Projector Mode See "Choosing a location" on page 11 for details.
Test Pattern
The projector can display several test patterns. It helps you
adjust the image size and focus and check that the projected
image is free from distortion.
Light Source
Settings
Light Source Mode
See "Setting Lamp Mode" on page 37 for details.
Reset Light Timer
Resets the lamp timer after new lamp is installed. For changing
the lamp, please contact qualified service personnel.
Light Source Information
See "Getting to know the lamp hour" on page 36 for details on
how the total lamp hour is calculated.
12V Trigger
There is one 12V trigger that works according to your needs
for installation scenarios. Two selections are available:
Off
If this is selected, the projector will not send electronic signal
out when it is turned on.
On
The projector will send a low to high electronic signal out
when it is turned on, a high to low signal out when it is turned
off.
High Altitude
Mode
A mode for operation in high altitude areas. See "Operating in
a high altitude environment" on page 26 for details.
INSTALLATION menu
34
Function Description
Language Sets the language for the On-Screen Display (OSD) menus.
See "Using the menus" on page 17 for details.
Background
Color Sets the background color for the projector.
Splash Screen Allows you to select which logo screen will be displayed
during projector start-up.
Auto Power Off See "Setting Auto Power Off" on page 37 for details.
Direct Power
On
Selecting On allows the projector to turn on automatically
once the power is fed through the power cord.
Menu Settings
Menu Display Time
Sets the length of time the OSD will remain active after your
last key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Reminder Message
Sets the reminder messages (e.g., the blank message, source
information, power saving message, source detection
message, and auto sync message) on or off.
Rename Input
Renames the current input source to your desired name. Use
/ / / to set the desired characters for the connected
source item.
Auto Input
Search See "Switching input signal" on page 20 for details.
SYSTEM SETUP: BASIC menu
35
Function Description
HDR
HDR
The projector supports HDR imaging sources. It can
automatically detect the dynamic range of the source from
HDMI 1, and optimize settings to reproduce contents under
wide range of light conditions. If the input source is not
defined with dynamic range, you can also manually select
Auto or SDR for it. Adjusting the setting will have no impact
if the projector receives a non-HDR content.
EOTF
The projector can automatically adjust the brightness levels of
your image according to the input source. You can also
manually select a brightness level to display better picture
quality. When the value is higher, the image becomes brighter;
when the value is lower, the image becomes darker. This
function is not available when SDR is selected in the HDR
menu.
Audio Settings See "Adjusting the sound" on page 26 for details.
HDMI Range See "Changing HDMI input settings" on page 20 for details.
Password See "Utilizing the password function" on page 18 for details.
Panel Key Lock See "Locking control keys" on page 26 for details.
Reset All
Settings
Returns all settings to the factory preset values.
The following settings will still remain: Picture Mode,
Brightness, Contrast, Color, Tint, Sharpness, Advanced,
Aspect Ratio, Silence, Projector Mode, Light Source
Mode, Rename Input, EOTF, Password.
Input
Shows the current signal source.
Picture Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format.
Light Source Usage Time
Shows the number of hours the light source has been used.
Firmware Version
Shows the current firmware version.
SYSTEM SETUP: ADVANCED menu
Information menu
36
Maintenance
Care of the projector
You need to keep the lens and/or filter (optional accessory) clean on a regular basis.
Never remove any parts of the projector. Contact your dealer when any part of the projector
needs replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 27 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 40 or
consult your dealer about the range.
• Retract the adjuster foot.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
37
1. Open the OSD menu and go to the INSTALLATION > Light Source Settings >
Light Source Information menu.
2. Press Enter and the Light Source Information page is displayed.
3. Light Source Usage Time displays the number of hours the lamp has been used.
Equivalent Lamp Hour displays the overall lamp life. The method of calculating the
equivalent lamp hour is as follows: Total (equivalent) Lamp Hour = 3.0 x (hours used
in Normal mode) + 1.5 x (hours used in Eco mode) + 1.875 x (hours used in
Dynamic mode) + 1 x (hours used in SuperEco mode)
The light source modes involved may differ. Please refer to the actual OSD of your projector.
4. To leave the menu, press Exit.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode
Setting the projector in Eco/Dynamic/SuperEco mode reduces system noise, power
consumption and extends the lamp operation life.
To set the lamp mode, go to the INSTALLATION > Light Source Settings > Light
Source Mode menu and press / to select.
The light source modes involved may differ. Please refer to the actual OSD of your projector.
Setting Auto Power Off
This function allows the projector to turn off automatically after a set period of time once no
input source is detected to prevent unnecessary waste of lamp life.
1. Open the OSD menu and go to the SYSTEM SETUP: BASIC > Auto Power Off
menu and press /.
2. If the preset time lengths are not suitable for your need, select Disable. The projector
will not automatically shut down in a certain time period.
Timing of replacing the lamp
Please install a new lamp or consult your dealer when the Lamp indicator light lights up.
An old lamp may cause a malfunction in the projector and in some instances the lamp may
explode.
CAUTION
The Lamp indicator light and Temperature indicator light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp indicator light or
Temperature indicator light still lights up after turning the power back on, please contact your
dealer. See "Indicators" on page 38 for details.
Lamp mode Description
Normal Provides full lamp brightness.
Eco Reduces lamp power consumption by 30% and lowers brightness to
extend the lamp life and decreases the fan noise.
Dynamic Reduces lamp power consumption by up to 70% depending on the
content brightness level.
SuperEco Reduces lamp power consumption by 70% and lowers brightness to
extend the lamp life and decreases the fan noise.
38
Replacing the lamp
Turn the power off and disconnect the projector from the power outlet. Please contact
qualified service personnel for changing the lamp.
Indicators
Light Status & Description
Power events
Blue Off Off Stand-by mode
Blue
Flashing Off Off Powering up
Blue Off Off Normal operation
Pink
Flashing Off Off Normal power-down cooling
Red
Flashing
Red
Flashing
Red
Flashing Downloading
Blue Off Red Phosphor/Color wheel start fail
Blue Off Red
Flashing Phosphor/Color wheel spin fail
Red Off Red Scaler reset fail
Blue Off Off Burn in on
Blue Blue Blue Burn in off
Lamp events
Off Off Red Light source error in normal operation
Off Off Pink
Flashing Light source is not lit up
Thermal events
Red Red Off Fan 1 error (the actual fan speed is outside the desired
speed.)
Red Red
Flashing Off Fan 2 error (the actual fan speed is outside the desired
speed.)
Red Blue Off Fan 3 error (the actual fan speed is outside the desired
speed.)
Blue Red Off Thermal sensor 1 open error (the remote diode has an
open-circuit condition.)
39
Troubleshooting
The projector does not turn on.
No picture
Blurred image
Remote control does not work
Cause Remedy
There is no power from the power cord.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the power
outlet. If the power outlet has a switch, make sure
that it is switched on.
Attempting to turn the projector on again
during the cooling process. Wait until the cooling down process has completed.
Cause Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the signal
cable is connected correctly.
The projector is not correctly connected to
the input signal device. Check the connection.
The input signal has not been correctly
selected.
Select the correct input signal with the Source key
on the projector or remote control.
Cause Remedy
The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as well as
the height of the projector if necessary.
Cause Remedy
The battery is out of power. Replace the battery with a new one.
There is an obstacle between the remote
control and the projector. Remove the obstacle.
You are too far away from the projector. Stand within 8 meters (26 feet) from the projector.
40
Specifications
Dimensions
332 mm (W) x 121 mm (H) x 261 mm (D) (Excluding extrusions)
Ceiling mount installation
261
121
332
Unit: mm
66.34 86.93
63.62
60.87
199.55
198.1
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
41
IR control table
Key Format Byte1 Byte2 Byte3 Byte4
On NEC-F2 83 F4 4F B0
Off NEC-F2 83 F4 4E B1
COMP NEC-F2 83 F4 41 BE
HDMI 1 NEC-F283F458A7
HDMI 2 NEC-F2 83 F4 59 A6
Auto Sync NEC-F2 83 F4 8 F7
Source NEC-F2 83 F4 40 BF
Up/ NEC-F2 83 F4 0B F4
Left NEC-F2 83 F4 0E F1
Enter NEC-F2 83 F4 15 EA
Right NEC-F2 83 F4 0F F0
Down/ NEC-F2 83 F4 0C F3
Menu NEC-F2 83 F4 30 CF
(Information) NEC-F2 83 F4 97 68
Exit NEC-F2 83 F4 28 D7
Aspect NEC-F2 83 F4 13 EC
Pattern NEC-F2 83 F4 55 AA
Blank NEC-F2 83 F4 7 F8
HDR NEC-F2 83 F4 A0 5F
(Mute) NEC-F2 83 F4 14 EB
(Volume Down) NEC-F2 83 F4 83 7C
(Volume Up) NEC-F2 83 F4 82 7D
Brightness NEC-F2 83 F4 60 9F
Contrast NEC-F2 83 F4 61 9E
Color Temp NEC-F2 83 F4 66 99
Silence NEC-F2 83 F4 A1 5E
Standard NEC-F2 83 F4 62 9D
User1 NEC-F283F4847B
Eco Mode NEC-F2 83 F4 2B D4
Movie NEC-F283F4649B
User2 NEC-F283F4857A
42
Address code
RS232 command table
<Pin assignment for this two end>
<Interface>
Code 1 83F4
Code 2 93F4
Code 3 A3F4
Code 4 B3F4
Code 5 C3F4
Code 6 D3F4
Code 7 E3F4
Code 8 F3F4
Pin Description Pin Description
1NC2RX
3TX4NC
5GND6NC
7RTSZ8CTSZ
9NC
RS-232 protocol
Baud Rate 9600 bps (default)
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
43
<RS232 command table>
Function Type Operation ASCII
Power
Write Power On <CR>*pow=on#<CR>
Write Power off <CR>*pow=off#<CR>
Read Power Status <CR>*pow=?#<CR>
Source
Selection
Write COMPUTER <CR>*sour=RGB#<CR>
Write HDMI <CR>*sour=hdmi#<CR>
Write HDMI 2 <CR>*sour=hdmi2#<CR>
Read Current source <CR>*sour=?#<CR>
Picture Mode
Write Bright <CR>*appmod=bright#<CR>
Write Standard <CR>*appmod=std#<CR>
Write Movie <CR>*appmod=dci#<CR>
Write User1 <CR>*appmod=user1#<CR>
Write User2 <CR>*appmod=user2#<CR>
Read Picture Mode <CR>*appmod=?#<CR>
Picture Setting
Write Contrast + <CR>*con=+#<CR>
Write Contrast - <CR>*con=-#<CR>
Read Contrast value <CR>*con=?#<CR>
Write Brightness + <CR>*bri=+#<CR>
Write Brightness - <CR>*bri=-#<CR>
Read Brightness value <CR>*bri=?#<CR>
Write Color + <CR>*color=+#<CR>
Write Color - <CR>*color=-#<CR>
Read Color value <CR>*color=?#<CR>
Write Tint + <CR>*tint=+#<CR>
Write Tint - <CR>*tint=-#<CR>
Read Tint value <CR>*tint=?#<CR>
Write Sharpness + <CR>*sharp=+#<CR>
Write Sharpness - <CR>*sharp=-#<CR>
Read Sharpness value <CR>*sharp=?#<CR>
Write Skin Tone + <CR>*skintone=+#<CR>
44
Picture Setting
Write Skin Tone - <CR>*skintone=-#<CR>
Read Skin Tone value <CR>*skintone=?#<CR>
Write Color Temperature-Warm <CR>*ct=warm#<CR>
Write Color Temperature-Normal <CR>*ct=normal#<CR>
Write Color Temperature-Cool <CR>*ct=cool#<CR>
Read Color Temperature Status <CR>*ct=?#<CR>
Write Aspect 4:3 <CR>*asp=4:3#<CR>
Write Aspect 16:9 <CR>*asp=16:9#<CR>
Write Aspect 2.35:1 <CR>*asp=2.35:1#<CR>
Write Aspect Auto <CR>*asp=AUTO#<CR>
Read Aspect Status <CR>*asp=?#<CR>
Write Overscan Adjustment + <CR>*overscan=+#<CR>
Write Overscan Adjustment - <CR>*overscan=-#<CR>
Read Overscan Adjustment value <CR>*overscan=?#<CR>
Write Auto <CR>*auto#<CR>
Write Red Gain + <CR>*RGain=+#<CR>
Write Red Gain - <CR>*RGain=-#<CR>
Read Red Gain value <CR>*RGain=?#<CR>
Write Green Gain + <CR>*GGain=+#<CR>
Write Green Gain - <CR>*GGain=-#<CR>
Read Green Gain value <CR>*GGain=?#<CR>
Write Blue Gain + <CR>*BGain=+#<CR>
Write Blue Gain - <CR>*BGain=-#<CR>
Read Blue Gain value <CR>*BGain=?#<CR>
Write Red Offset + <CR>*ROffset=+#<CR>
Write Red Offset - <CR>*ROffset=-#<CR>
Read Red Offset value <CR>*ROffset=?#<CR>
Write Green Offset + <CR>*GOffset=+#<CR>
Write Green Offset - <CR>*GOffset=-#<CR>
Read Green Offset value <CR>*GOffset=?#<CR>
Write Blue Offset + <CR>*BOffset=+#<CR>
45
Picture Setting
Write Blue Offset - <CR>*BOffset=-#<CR>
Read Blue Offset value <CR>*BOffset=?#<CR>
Write Gamma Selection-1.8 <CR>*gamma=1.8#<CR>
Write Gamma Selection-2.0 <CR>*gamma=2.0#<CR>
Write Gamma Selection-2.2 <CR>*gamma=2.2#<CR>
Write Gamma Selection-2.3 <CR>*gamma=2.3#<CR>
Write Gamma Selection-2.4 <CR>*gamma=2.4#<CR>
Write Gamma Selection-2.5 <CR>*gamma=2.5#<CR>
Write Gamma Selection-2.6 <CR>*gamma=2.6#<CR>
Write Gamma Selection-2.8 <CR>*gamma=2.8#<CR>
Write Gamma Selection-Custom 1 <CR>*gamma=c1#<CR>
Write Gamma Selection-Custom 2 <CR>*gamma=c2#<CR>
Read Gamma Selection Status <CR>*gamma=?#<CR>
Operation
Settings
Write Splash Screen -Black <CR>*splash=black#<CR>
Write Splash Screen -Blue <CR>*splash=blue#<CR>
Write Splash Screen Status <CR>*splash=?#<CR>
Write Background Color - Green <CR>*background=green#<CR>
Write Background Color - Black <CR>*background=black#<CR>
Write Background Color - Blue <CR>*background=blue#<CR>
Read Background Color States <CR>*background=?#<CR>
Write Projector Position-Front Table <CR>*pp=FT#<CR>
Write Projector Position-Rear Table <CR>*pp=RE#<CR>
Write Projector Position-Rear Ceiling <CR>*pp=RC#<CR>
Write Projector Position-Front Ceiling <CR>*pp=FC#<CR>
Read Projector Position Status <CR>*pp=?#<CR>
Write Quick auto search on/Auto source
search on <CR>*QAS=on#<CR>
Write Quick auto search off/Auto source
search off <CR>*QAS=off#<CR>
Read Quick auto search status/Auto
source search status <CR>*QAS=?#<CR>
Write Menu Display Time -Always On <CR>*menutime=on#<CR>
Write Menu Display Time -5 sec <CR>*menutime=5s#<CR>
46
Operation
Settings
Write Menu Display Time -10 sec <CR>*menutime=10s#<CR>
Write Menu Display Time -15 sec <CR>*menutime=15s#<CR>
Write Menu Display Time -20 sec <CR>*menutime=20s#<CR>
Write Menu Display Time -25 sec <CR>*menutime=25s#<CR>
Write Menu Display Time -30 sec <CR>*menutime=30s#<CR>
Read Menu Display Time Status <CR>*menutime=?#<CR>
Write Menu Position - Center
<CR>*menuposition=center#<CR>
Write Menu Position - Top-Left <CR>*menuposition=tl#<CR>
Write Menu Position - Top-Right <CR>*menuposition=tr#<CR>
Write Menu Position - Bottom-Right <CR>*menuposition=br#<CR>
Write Menu Position - Bottom-Left <CR>*menuposition=bl#<CR>
Read Menu Position Status <CR>*menuposition=?#<CR>
Write Reminder Message - On <CR>*reminder=on#<CR>
Write Reminder Message - Off <CR>*reminder=off#<CR>
Read Reminder Message Status <CR>*reminder=?#<CR>
Write Direct Power On-on <CR>*directpower=on#<CR>
Write Direct Power On-off <CR>*directpower=off#<CR>
Read Direct Power On-Status <CR>*directpower=?#<CR>
Lamp Control
Read Lamp Hour <CR>*ltim=?#<CR>
Write Normal mode <CR>*lampm=lnor#<CR>
Write Eco mode <CR>*lampm=eco#<CR>
Write Dynamic <CR>*lampm=dynamic#<CR>
Read Lamp Mode Status <CR>*lampm=?#<CR>
Miscellaneous
Read Model Name <CR>*modelname=?#<CR>
Write Blank On <CR>*blank=on#<CR>
Write Blank Off <CR>*blank=off#<CR>
Read Blank Status <CR>*blank=?#<CR>
Write Menu On <CR>*menu=on#<CR>
Write Menu Off <CR>*menu=off#<CR>
47
Miscellaneous
Write Up <CR>*up#<CR>
Write Down <CR>*down#<CR>
Write Right <CR>*right#<CR>
Write Left <CR>*left#<CR>
Write Enter/OK <CR>*enter#<CR>
Write BACK <CR>*back#<CR>
Write Language + <CR>*lang=+#<CR>
Write Language - <CR>*lang=-#<CR>
Read Language Status <CR>*lang=?#<CR>
Write Auto Power off -disable <CR>*APOFF=DIS#<CR>
Write Auto Power off - 5 min <CR>*APOFF=5#<CR>
Write Auto Power off - 10 min <CR>*APOFF=10#<CR>
Write Auto Power off - 15 min <CR>*APOFF=15#<CR>
Write Auto Power off - 20 min <CR>*APOFF=20#<CR>
Write Auto Power off - 25 min <CR>*APOFF=25#<CR>
Write Auto Power off - 30 min <CR>*APOFF=30#<CR>
Read Auto Power off Status <CR>*APOFF=?#<CR>
Write High Altitude mode on <CR>*Highaltitude=on#<CR>
Write High Altitude mode off <CR>*Highaltitude=off#<CR>
Read High Altitude mode status <CR>*Highaltitude=?#<CR>
Write Key Lock on <CR>*keylock=on#<CR>
Write Key Lock off <CR>*keylock=off#<CR>
Read Key Lock status <CR>*keylock=?#<CR>
48
Timing chart
Analog RGB
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
VGA 640 x 480 4:3 60/72/75/85
SVGA 800 x 600 4:3 60/72/75/85
XGA
1024 x 768 4:3 60/70/75/85
1152 x 864 4:3 75
WXGA
1280 x 768 15:9 60
1280 x 800 16:10 60/75/85
1360 x 768 16:9 60
1366 x 768 16:9 60
Quad-VGA 1280 x 960 4:3 60/85
SXGA 1280 x 1024 5:4 60
SXGA+ 1400 x 1050 4:3 60
WXGA+ 1440 x 900 16:10 60
UXGA 1600 x 1200 4:3 60
WSXGA+ 1680 x 1050 16:10 60
HD 1280 x 720 16:9 60
Full HD 1920 x 1080 16:9 60
WUXGA 1920 x 1200 RB 16:10 60
MAC 13" 640 x 480 4:3 67
MAC 16" 832 x 624 4:3 75
MAC 19" 1024 x 768 4:3 75
MAC 21" 1152 x 870 4:3 75
49
HDMI
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
VGA 640 x 480 4:3 60
SVGA 800 x 600 4:3 60
XGA 1024 x 768 4:3 60
WXGA
1280 x 768 15:9 60
1280 x 800 16:10 60
1360 x 768 16:9 60
Quad-VGA 1280 x 960 4:3 60
SXGA 1280 x 1024 5:4 60
SXGA+ 1400 x 1050 4:3 60
WXGA+ 1440 x 900 16:10 60
WSXGA+ 1680 x 1050 16:10 60
4k2k 3840 x 2160 16:9 24
4k2k 3840 x 2160 16:9 25
4k2k 3840 x 2160 16:9 30
4k2k (HDMI 1 only) 3840 x 2160 16:9 50
4k2k (HDMI 1 only) 3840 x 2160 16:9 60
HDTV (1080p) 1920 x 1080 16:9 50 / 60
HDTV (1080i) 1920 x 1080 16:9 50 / 60
HDTV (720p) 1280 x 720 16:9 50 / 60
SDTV (480p) 720 x 480 4:3 / 16:9 60
SDTV (576p) 720 x 576 4:3 / 16:9 50
SDTV (480i) 720 x 480 4:3 / 16:9 60
SDTV (576i) 720 x 576 4:3 / 16:9 50
50
Projector specifications
All specifications are subject to change without notice.
Not all models can be purchased in your region.
Product Specification
Resolution 4K UHD 3840 x 2160
Throw ratio 1.47~1.76 (95”±3%@3.09m, 4K)
Display system 1-CHIP DMD
Lamp Type 240 W (RLC-117)
Input connector
RGB-in 1
Component input -
S-Video -
Composite input -
Audio-in 1
RCA R&L -
Mini USB 1 (firmware upgrade)
HDMI HDMI 2.0 x 1/HDMI 1.4 x 1
HDMI/MHL
-
Output connector
RGB-out -
USB-A (5V/1.5A) 1
Mini USB (5V/1.5A) -
Audio-out 1
Speaker 10 W
Control terminal
RS-232 serial control 9 pin x 1
LAN -
IR receiver 2 (Front/Top)
12V trigger 1
Mechanical
Net Weight 4.01 Kg (8.84 lbs)
Electrical
Power Source AC100–240V, 50–60 Hz
Power Consumption STD: 375 W (Max); < 0.5 W (Standby)
Environmental Requirements
Operating Temperature 0°C–40°C at sea level
Operating Altitude 0–1499 m at 5°C–35°C
1500–3000 m at 5°C–25°C
Operating Relative
Humidity 10%–90% (without condensation)
51
Copyright information
Copyright
Copyright © 2018. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region Website T= Telephone
C = CHAT ONLINE Email
Australia
New Zealand www.viewsonic.com.au AUS= 1800 880 818
NZ= 0800 008 822 service@au.viewsonic.com
Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com
Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com
India www.in.viewsonic.com T= 1800 419 0959 service@in.viewsonic.com
Korea ap.viewsonic.com/kr/ T= 080 333 2131 service@kr.viewsonic.com
Latin America
(Argentina) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Chile) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Columbia) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Latin America
(Mexico) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.
Tel: 55) 6547-6454 55)6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico
Latin America
(Peru) www.viewsonic.com/la/ C= http://www.viewsonic.com/
la/soporte/servicio-tecnico soporte@viewsonic.com
Macau www.hk.viewsonic.com T= 853-2840-3687 service@hk.viewsonic.com
Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com
Puerto Rico &
Virgin Islands www.viewsonic.com
T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/
la/soporte/servicio-tecnico
service.us@viewsonic.com
soporte@viewsonic.com
Singapore/
Malaysia/Thailand www.ap.viewsonic.com T= 65 6461 6044 service@sg.viewsonic.com
South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com
United States www.viewsonic.com T= 1-800-688-6688 service.us@viewsonic.com
52
Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
IRUODERUDQGRQH\HDUIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHU
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
RULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH(XURSH2QH\HDU
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days
IRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH
Other regions or countries: Please check with your local dealer or local ViewSonic
RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWR
manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration, failure, or malfunction resulting from:
D$FFLGHQWDEXVHPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUH
LPSURSHUPDLQWHQDQFHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRUIDLOXUHWRIROORZ
instructions supplied with the product.
E2SHUDWLRQRXWVLGHRISURGXFWVSHFL¿FDWLRQV
c. Operation of the product for other than the normal intended use or not under
normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
J&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH
K8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
53
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
FRQWDLQHGKHUHLQLQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUD
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
XSRQLQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRI
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWV
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
54
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of
WKH¿UVWFRQVXPHUSXUFKDVH
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU
What the warranty does not cover:
$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG
2. Damage, deterioration or malfunction resulting from:
D$FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFW
PRGL¿FDWLRQXQDXWKRUL]HGDWWHPSWHGUHSDLURUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHGZLWKWKH
product.
b. Any damage of the product due to shipment.
F&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH
G8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
LQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
55
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
Tel: 800-688-6688
E-Mail: http://www.viewsonic.com
Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006
56
