Table of Contents
Viewsonic VP2776 User Manual
Displayed below is the user manual for VP2776 by Viewsonic which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
VP2776
Display
User Guide
Model No. VS18610
P/N: VP2776
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in
a safe manner, as well as registering your product for future service. Warranty information contained in this User
Guide will describe your limited coverage from ViewSonic® Corporation, which is also found on our web site at
http://www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right
corner of our website.
2
Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding
the world’s expectations for technological evolution, innovation, and simplicity.
At ViewSonic®, we believe that our products have the potential to make a positive
impact in the world, and we are confident that the ViewSonic® product you have
chosen will serve you well.
Once again, thank you for choosing ViewSonic®!
3
Safety Precauons
Please read the following Safety Precautions before you start using the device.
• Keep this user guide in a safe place for later reference.
• Read all warnings and follow all instructions.
• Sit at least 18" (45 cm) away from the device.
• Allow at least 4" (10 cm) clearance around the device to ensure proper
ventilation.
• Place the device in a well-ventilated area. Do not place anything on the device
that prevents heat dissipation.
• Do not use the device near water. To reduce the risk of fire or electric shock, do
not expose the device to moisture.
• Avoid exposing the device to direct sunlight or other sources of sustained heat.
• Do not install near any heat sources such as radiators, heat registers, stoves, or
other devices (including amplifiers) that may increase the temperature of the
device to dangerous levels.
• Use a soft, dry cloth to clean the external housing. For more information, refer
to the "Maintenance" section of this manual.
• Avoid touching the screen, as oil may collect on the screen if you touch it.
• Do not touch the screen surface with sharp or hard objects, as it may cause
damage to the screen.
• Do not place the device on cloth or other materials that may be placed between
the product and supporting furniture.
• When moving the device, be careful not to drop or bump the device on
anything.
• Do not place the device on an uneven or unstable surface. The device may fall
over resulting in an injury or a malfunction.
• Do not place any heavy objects on the device or connection cables.
• Always use cabinets, stands, or installation methods recommended by the
manufacturer of the device set.
• Always use furniture that can safely support the device.
• Always ensure the device is not overhanging the edge of the supporting
furniture.
• Do not place the device on tall furniture, such as cupboards or bookcases,
without anchoring both the furniture and the device to a suitable support.
• Always educate children about the dangers of climbing on furniture to reach the
device or related equipment.
4
• Do not place the monitor where children are likely to be present.
• Do not place items that might tempt children to climb, such as toys and remote
controls, on the top of the device or furniture on which the product is placed.
• If smoke, an abnormal noise, or a strange odor is present, immediately turn the
device off and call your dealer or ViewSonic®. It is dangerous to continue using
the device.
• Do not attempt to circumvent the safety provisions of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding prong. The
wide blade and the third prong are provided for your safety. If the plug does not
fit into your outlet, obtain an adapter and do not attempt to force the plug into
the outlet.
• When connecting to a power outlet, Do not remove the grounding prong. Please
ensure grounding prongs are never removed.
• Always route and manage cords and cables connected to your device so they
cannot be tripped over, pulled, or grabbed.
• Protect the power cord from being treaded upon or pinched, particularly at the
plug, and at the point where it emerges from the equipment. Ensure that the
power outlet is located near the equipment so that it is easily accessible.
• Disconnect the power plug from the power outlet if the device is not being used
for a long period of time.
• Please confirm the distribution system installed in the building. The system
should provide a circuit breaker rated at 120/240V, 20A.
• Only use attachments/accessories, such as carts, stands, tripods, brackets or
tables, specified by the manufacturer.
• When a cart is used, use with caution when moving the cart/equipment
combination to avoid injury from tipping over.
• Refer all servicing to qualified service personnel. Service will be required when
the unit has been damaged in any way, such as:
if the power-supply cord or plug is damaged.
if liquid is spilled onto or objects fall into the unit.
if the unit is exposed to rain or moisture.
if the unit does not operate normally or has been dropped.
• When using ear-/headphones, adjust the volume to appropriate levels, or
hearing damage may result.
5
• Fastening the display to a wall or fixed object using cordage or other restraining
devices can help support the weight of the display in order to prevent the
display from falling over.
Hole paern
(W x H)
Interface Pad
(W x H x D) Pad Hole Screw Specicaon & Quanty
100 x 100 mm 115 x 115 x 2.6 mm Ø 5 mm M4 x 10 mm
4 pieces
or
VESA wall mounng hole
NOTE:
• Restraining device/cordage should be able to withstand 100N force.
• Make sure the cordage is straightened, and any slack is removed. The back
of the device shall face the wall to ensure the device cannot tilt under
external force.
• Make sure the display does not tilt under external force at any height and
rotation angle of the device.
• If the existing display is going to be retained and relocated, the same
considerations as above should be applied.
66
Contents
Safety Precautions ....................................................... 3
Introduction ................................................................ 8
Package Contents ...................................................................................................8
Product Overview ...................................................................................................9
Initial Setup ............................................................... 10
Installing the Stand ...............................................................................................10
Wall Mounting ......................................................................................................12
Using the Security Slot .................................................................... ...................... 14
Making Connections .................................................. 15
Connecting to Power ............................................................................................15
Connecting External Devices ................................................................................16
HDMI Connection .................................................................................................. 16
DisplayPort Connection ......................................................................................... 17
USB Connection ..................................................................................................... 18
Using the Monitor ..................................................... 19
Adjusting the Viewing Angle .................................................................... ............. 19
Height Adjustment ................................................................................................ 19
Tilt Angle Adjustment ............................................................................................ 20
Screen Orientation Adjustment (Monitor Pivot) ................................................... 20
Swivel Angle Adjustment ....................................................................................... 22
Turning the Device On/Off ...............................................23
Using the Joy Key ..................................................................................................24
Startup Menu ........................................................................................................ 24
Hot Keys ................................................................................................................ 27
Configuring the Settings .......................................................................................29
General Operations ............................................................................................... 29
On-Screen Display (OSD) Menu Tree .................................................................... 31
Menu Options ....................................................................................................... 40
7
Advanced Features and Settings ................................ 47
HDR (High-Dynamic-Range) .................................................................................. 47
KVM ......................................................................................................................48
Auto Pivot .............................................................................................................50
Colorbration+ .......................................................................................................51
Dual Color .............................................................................................................52
Multi-Picture .........................................................................................................53
PBP (Picture-by-Picture) ........................................................................................ 54
PIP (Picture-in-Picture) .......................................................................................... 55
Backstage Lighting ................................................................................................56
Firmware Update .................................................................... ..............................57
Appendix ................................................................... 58
Specifications .................................................................... .................................... 58
Glossary ................................................................................................................60
Troubleshooting ...................................................................................................65
Maintenance.........................................................................................................67
General Precautions .............................................................................................. 67
Cleaning the Screen ............................................................................................... 67
Cleaning the Case .................................................................................................. 67
Regulatory and Service Information .......................... 68
Compliance Information ....................................................................................... 68
FCC Compliance Statement ................................................................................... 68
Industry Canada Statement ................................................................................... 68
CE Conformity for European Countries ................................................................. 68
Declaration of RoHS2 Compliance......................................................................... 69
Indian Restriction of Hazardous Substances ......................................................... 70
Product Disposal at End of Product Life ................................................................ 70
Copyright Information ..........................................................................................71
Customer Service .................................................................................................. 72
Limited Warranty .................................................................................................. 73
Mexico Limited Warranty ...................................................................................... 76
8
Introducon
Package Contents
• Monitor
• Power cord
• Video cable
• Quick start guide
NOTE: The power cord and video cables included in your package may vary
depending on your country. Please contact your local reseller for more
informaon.
9
Product Overview
Front View
Rear View
Micro USB
5V/3A
Type-C Type-C
5V/3A
Micro USB
21
5 7 8
1 22 3 4 6
1. AC IN 2. HDMI 3. DisplayPort 4. USB Type-C
5. USB Upstream 6. USB Type-C
5V/3A
7. USB Downstream 8. Micro USB
NOTE: For more informaon about the Joy Key and its funcons, refer to “Hot
Keys”.
Display screen
Security Slot
Joy Key
Power Buon
10
Inial Setup
This secon provides detailed instrucons for seng up your monitor.
Installing the Stand
1. Place the monitor on a at, stable surface with the screen facing down.
2. Align and slide the upper hooks of the monitor stand into the stand mounng
slots.
11
3. Li the device into its upright posion on a at, stable surface.
NOTE: Always place the device on a at, stable surface. Failure to do so may
cause the device to fall and damage the device and/or result in personal
injury.
12
Wall Mounng
Refer to the table below for the standard dimensions for wall mount kits.
NOTE: For use only with a UL cered wall mount kit/bracket. To obtain a wall-
mounng kit or height adjustment base, contact ViewSonic® or your
local dealer.
Maximum
Loading
Hole paern
(W x H)
Interface Pad
(W x H x D) Pad Hole Screw Specicaon
& Quanty
14 kg 100 x 100 mm 115 x 115 x 2.6 mm Ø 5 mm M4 x 10 mm
4 pieces
NOTE: Wall mount kits are sold separately.
1. Turn o the device and disconnect all cables.
2. Place the device on a at, stable surface with the screen facing down.
3. Push and hold the quick release tab and carefully li the stand.
4. Pull down slightly to disengage the hooks and remove the stand.
13
5. Aach the mounng bracket to the VESA mounng holes at the rear of the
monitor. Then secure it with four (4) screws (M4 x 10 mm).
Micro USB
5V/3A
100 mm
100 mm
6. Follow the instrucons that come with the wall mounng kit to mount the
monitor onto the wall.
14
Using the Security Slot
To help prevent the device from being stolen, use a security slot locking device to
secure the device to a xed object.
Addionally, fastening the monitor to a wall or xed object using a security cable
can help support the weight of the monitor in order to prevent the monitor from
falling over.
Below is an example of seng up a security slot locking device on a table.
1515
Making Connecons
This secon guides you on how to connect the monitor with other equipment.
Connecng to Power
1. Connect the power cord to the AC IN jack at the rear of the device.
2. Connect the power cord plug to a power outlet.
Micro USB
5V/3A
12
16
Connecng External Devices
HDMI Connecon
Connect one end of an HDMI cable to the HDMI port of your monitor. Then connect
the other end of the cable to the HDMI port of your computer.
NOTE: The monitor is equipped with two HDMI 2.0 ports.
Micro USB
5V/3A
HDMI
21
17
DisplayPort Connecon
Connect one end of a DisplayPort cable to the DisplayPort port. Then connect the
other end of the cable to the DisplayPort or mini DP port of your computer.
NOTE: To connect the monitor to the Thunderbolt port (v. 1&2) on your Mac,
connect the mini DP end of the “mini DP to DisplayPort cable” to the
Thunderbolt output of your Mac. Then connect the other end of the
cable to the DisplayPort port of the monitor.
Micro USB
5V/3A
18
USB Connecon
Connect one end of a USB cable to a USB port of the monitor. Then connect the
other end of the cable to a USB port of your computer.
NOTE: The monitor supports four (4) types of USB ports. When making the
connecon(s), observe the following guidelines:
• Two (2) USB Type A ports: Connecon for your Type A peripheral
device(s) (i.e. storage device, keyboard, mouse).
NOTE: To use some peripherals, please ensure your computer is
also connected to the monitor’s USB Type B port.
• One (1) USB Type B port: Connect the USB Type B male cable (square
with 2 cut corners) to this port, and then connect the other end of the
cable to the USB downstream port of your computer.
• Two (2) USB Type C ports: Make sure your Type-C output device and
cable support video signal transmission.
NOTE: Only the Type-C port supports video transmission; the
Type-C 5V/3A port only supports power delivery and data
transmission.
• One (1) Micro USB port:
Micro USB
5V/3A
Type-C
Type-C Type-C
5V/3A
Micro USB
NOTE: It is not necessary to connect to all three types of USB ports at the same
me. The user’s personal usage scenario will determine which, if any,
USB ports are used.
19
Using the Monitor
Adjusng the Viewing Angle
For opmal viewing, you can adjust the viewing angle using any of the following
methods:
Height Adjustment
Lower or raise the monitor to the desired height (0 to 130 mm).
NOTE: When adjusng, press down rmly along the adjustment track holding
the monitor with both hands on the side.
20
Tilt Angle Adjustment
Tilt the monitor forwards or backwards to the desired viewing angle (-5˚ to 21˚).
NOTE: When adjusng, support the stand rmly with one hand while lng the
monitor forwards or backwards with the other hand.
Screen Orientaon Adjustment (Monitor Pivot)
1. Adjust the monitor height to the highest posion. Then lt the monitor
backwards to the full lt posion.
21
2. Rotate the monitor 90° clockwise or counter clockwise from landscape to portrait
orientaon.
NOTE:
• When adjusng, make sure to hold both sides of your monitor rmly with
both hands.
• If using the Auto Pivot funcon, the system can detect the screen
orientaon automacally.
22
Swivel Angle Adjustment
Swivel the monitor to the le or right for the desired viewing angle (60˚).
23
Turning the Device On/Off
1. Plug the power cord into a power outlet.
2. Press the Power buon to turn on the monitor.
3. To turn the monitor o, press the Power buon again.
Micro USB
5V/3A
NOTE: The monitor will sll consume some power as long as the power cord
is connected to the power outlet. If the monitor is not being used for a
long period of me, please disconnect the power plug from the power
outlet.
24
Using the Joy Key
Use the Joy Key to access the Startup Menu, acvate Hot Keys, navigate the On-
Screen Display (OSD) Menu, and change the sengs.
Micro USB
5V/3A
Joy Key
Startup Menu
Move the joy key t to acvate the Startup Menu.
NOTE: Follow the key guide that appears on the screen to select the opon or
make adjustments.
Main Menu
Enter the On-Screen Display (OSD) Menu.
25
Color Mode
Select one of the preset standard color sengs.
ViewMode
Select one of the preset display sengs.
Brightness
Adjust the brightness level.
26
Input
Select the input source.
Volume
Adjust the volume sengs.
NOTE: Move the joy key t to return to the previous menu.
27
Hot Keys
When the On-Screen Display (OSD) Menu is o, you can quickly access special
funcons by using the Joy Key.
Key Descripon
lPress and hold the key for 5 seconds to acvate/deacvate LED
lighng.
Backstage Lighting
ON
qPress and hold the key to lock/unlock the OSD Menu.
When the menu appears on the screen, connue holding both keys
for 10 seconds to lock/unlock the OSD Menu.
1
OSD Lock/Unlocked
Locking OSD
Press and hold for 5 sec
to lock OSD
If the OSD Menu is locked, the below message will appear on the
screen:
OSD Lock/Unlocked
OSD Locked
28
Key Descripon
pPress and hold the key to lock/unlock the Power button.
When the menu appears on the screen, continue holding both keys
for 10 seconds to lock/unlock the Power button.
3
Power Lock/Unlock
Locking Power Button
Press and hold for 10s
to lock power
1
Power Lock/Unlocked
Locking Power Button
Press and hold for 5 sec
to lock Power
If the Power button is locked, the below message will appear on
the screen:
Power Lock/Unlock
Power Button Locked
3
Power Lock/Unlock
Locking Power Button
Press and hold for 10s
to lock power
Power Lock/Unlocked
Power Button Locked
tPress and hold the key for 10 seconds to display/hide the boot up
screen when the device is turned on.
Logo Boot Up Screen On/Off
Off
Press to turn On
uPress and hold the key for 10 seconds to activate/deactivate Ultra
Fast.
Boot Up Screen On/Off
Off
Press to turn on
Ultra Fast
ON
29
Conguring the Sengs
General Operaons
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select the main menu. Then press the l key to enter
the selected menu.
30
3. Move the joy key p or q to select the desired menu opon. Then press the l key
to enter the sub-menu.
4. Move the joy key p or q to adjust/select the seng. Then press the l key to
conrm.
5. Move the joy key t to return to the previous menu.
31
On-Screen Display (OSD) Menu Tree
Main Menu Sub-menu Menu Opon
Input Select
DisplayPort
Color Format
Auto
RGB (Full Range)
RGB (Limited Range)
YUV (Full Range)
YUV (Limited Range)
DisplayPort 1.4 On
O
HDMI 1
Color Format
Auto
RGB (Full Range)
RGB (Limited Range)
YUV (Full Range)
YUV (Limited Range)
HDMI 2.0 On
O
HDMI 2
Color Format
Auto
RGB (Full Range)
RGB (Limited Range)
YUV (Full Range)
YUV (Limited Range)
HDMI 2.0 On
O
Type C
Color Format
Auto
RGB (Full Range)
RGB (Limited Range)
YUV (Full Range)
YUV (Limited Range)
USB 3.2 On
O
DisplayPort 1.4 On
O
Auto Detect On
O
32
Main Menu Sub-menu Menu Opon
Color Mode
DCI-P3
Brightness (-/+, 0~100)
Color
Temperature
9300K
7500K
6500K
6300K
5000K
Gamma
1
1.4
1.8
2.2
2.4
2.6
Sharpness (-/+, 0~100)
Aspect Rao
1:1
4:3
Full Screen
Uniformity On
O
Recall
sRGB
Brightness (-/+, 0~100)
Color
Temperature
9300K
7500K
6500K
6300K
5000K
Gamma
1
1.4
1.8
2.2
2.4
2.6
Sharpness (-/+, 0~100)
Aspect Rao
1:1
4:3
Full Screen
Uniformity On
O
Recall
33
Main Menu Sub-menu Menu Opon
Color Mode
REC709
Brightness (-/+, 0~100)
Color
Temperature
9300K
7500K
6500K
6300K
5000K
Gamma
1
1.4
1.8
2.2
2.4
2.6
Sharpness (-/+, 0~100)
Aspect Rao
1:1
4:3
Full Screen
Uniformity On
O
Recall
DICOM-SIM
Sharpness (-/+, 0~100)
Aspect Rao
1:1
4:3
Full Screen
Recall
34
Main Menu Sub-menu Menu Opon
Color Mode
User
Contrast (-/+, 0~100)
Brightness (-/+, 0~100)
Color
Temperature
9300K
7500K
6500K
6300K
5000K
Gamma
1
1.4
1.8
2.2
2.4
2.6
Advanced DCR (-/+,
0/25/50/75/100)
Gain
Red (-/+, 0~100)
Green (-/+, 0~100)
Blue (-/+, 0~100)
Oset
Red (-/+, 0~100)
Green (-/+, 0~100)
Blue (-/+, 0~100)
Hue
Red (-/+, 0~100)
Green (-/+, 0~100)
Blue (-/+, 0~100)
Cyan (-/+, 0~100)
Magenta (-/+, 0~100)
Yellow (-/+, 0~100)
Sharpness (-/+, 0~100)
Aspect Rao
1:1
4:3
Full Screen
Blue Light Filter (-/+, 0~5)
Uniformity On
O
Recall
35
Main Menu Sub-menu Menu Opon
Color Mode
CAL1/CAL2/
CAL3
Brightness (-/+, 0~100)
Color Calibraon
Noce
Result
Remind Schedule
Hour
Counter Hour
Recall
Sharpness (-/+, 0~100)
Aspect Rao
1:1
4:3
Full Screen
Uniformity On
O
Recall
HDR
Standard
HDR_M
HDR_H
Smooth
O
36
Main Menu Sub-menu Menu Opon
ViewMode
CAD/CAM
Ultra Clear (-/+, 0~4)
Advanced-
Sharpness (-/+, 0~100)
Advanced-
Gamma (-/+, 1.8~2.6)
Video Edit
Ultra Clear (-/+, 0~4)
Advanced-
Sharpness (-/+, 0~100)
Advanced-
Gamma (-/+, 1.8~2.6)
Animaon
Ultra Clear (-/+, 0~4)
Advanced-
Sharpness (-/+, 0~100)
Black Stabilizaon (-/+, 0~10)
Photographer
Ultra Clear (-/+, 0~4)
Advanced-
Sharpness (-/+, 0~100)
Advanced-
Gamma (-/+, 1.8~2.6)
FPS 1
FPS 2
RTS
MOBA
Audio Adjust Volume (-/+, 0~100)
Mute On
O
Audio Input
DisplayPort
HDMI 1
HDMI 2
Type C
37
Main Menu Sub-menu Menu Opon
Setup Menu
Language Select
English
Français
Deutsch
Español
Italiano
Suomi
Русский
Türkçe
日本語
한국어
繁體中文
简体中文
Adapve Sync On
O
Resoluon
Noce
On
O
PureXP™ On
O
Informaon
OSD Timeout (-/+, 5/15/30/60)
OSD
Background
On
O
OSD Pivot
Auto
0°
+90°
-90°
180°
Power Indicator On
O
Auto Power O On
O
Sleep
30 minutes
45 minutes
60 minutes
120 minutes
O
38
Main Menu Sub-menu Menu Opon
Setup Menu
Mul-Picture
O
PBP Le-Right
Le Source Select
DisplayPort
HDMI 1
HDMI 2
Type C
Right Source Select
DisplayPort
HDMI 1
HDMI 2
Type C
Swap
PIP
PIP Source Select
DisplayPort
HDMI 1
HDMI 2
Type C
PIP Posion
PIP H. Posion
PIP V. Posion
PIP Size (-/+, 0~100)
Swap
Dual Color
DCI-P3
sRGB
REC709
DICOM-SIM
User
CAL 1
CAL 2
CAL 3
CAD/CAM
Video Edit
Animaon
Photographer
FPS 1
FPS 2
RTS
MOBA
39
Main Menu Sub-menu Menu Opon
Setup Menu
ECO Mode
Standard
Opmize
Conserve
Energy Saving On
O
Overscan On
O
Response Time
Standard
Advanced
Ultra Fast
USB Charging On
O
Backstage
Lighng
Level 1
Level 2
Level 3
O
Burn-in Eraser On
O
DDC/CI On
O
Rename
All Recall
40
Menu Opons
Input
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Input. Then press the l key to enter the Input
menu.
3. Move the joy key p or q to select the desired input source. Then press the l key
to conrm the selecon.
41
Color Mode
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Color Mode. Then press the l key to enter the
Color Mode menu.
3. Move the joy key p or q to select the desired opon. Then press the l key to
enter its sub-menu.
4. Move the joy key p or q to adjust/select the seng, and press the l key to
conrm the selecon (if applicable).
Menu Opon Descripon
DCI-P3 Precise color gamut and gamma of DCI-P3 standard.
sRGB Precise color gamut and gamma of sRGB standard.
REC709 Precise color gamut and gamma of ITU-R Rec. 709 standard.
DICOM-SIM Gamma curves are set to a DICOM simulaon.
User Custom, user-dened sengs.
CAL1/CAL2/CAL3 Display with the 1st/2nd/3rd user calibraon mode.
HDR Reduce the overall contrast of a given scene so that detail
in the highlights and shadows can be seen.
42
ViewMode
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select ViewMode. Then press the l key to enter the
ViewMode menu.
3. Move the joy key p or q to select the desired opon. Then press the l key to
enter its sub-menu.
Menu Opon Descripon
CAD/CAM Select this opon for viewing graphic design les.
Video Edit Select this opon for video eding.
Animaon Select this opon for animaon.
Photographer Select this opon for viewing photo les.
FPS 1 Ideal for First-Person Shooter games.
FPS 2 Ideal for First-Person Shooter games.
RTS Ideal for Real-Time Strategy games.
MOBA Select this opon for Mulplayer Online Bale Arena games.
43
Audio Adjust
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Audio Adjust. Then press the l key to enter
the Audio Adjust menu.
3. Move the joy key p or q to select the desired opon. Then press the l key to
enter its sub-menu.
4. Move the joy key p or q to adjust/select the seng, and press the l key to
conrm the selecon (if applicable).
Menu Opon Descripon
Volume Adjust the volume level.
Mute Enable this opon to temporarily turn o the sound.
Audio Input Select the audio input source.
44
Setup Menu
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Setup Menu. Then press the l key to enter
the Setup Menu menu.
3. Move the joy key p or q to select the desired opon. Then press the l key to
enter its sub-menu.
4. Move the joy key p or q to adjust/select the seng, and press the l key to
conrm the selecon (if applicable).
NOTE: Some sub-menu opons may have another sub-menu. To enter the
respecve sub-menu, press the l key. Follow the key guide that appears
on the boom of the screen to select the opon or make adjustments.
Menu Opon Descripon
Language Select Select an available language for the OSD Menu.
Adapve Sync Eliminates stuering and tearing during gameplay.
Resoluon Noce
Enable this opon to allow the system to inform users that
the current viewing resoluon is not the correct nave
resoluon.
PureXP™
Short for “Pure Experience”, this feature can enhance the
visual quality of moving objects, making them less vague
with a clearer view.
Informaon Display the monitor informaon.
OSD Timeout Set the length of me the OSD Menu remains on screen.
OSD Background Show/Hide the OSD background when the OSD Menu
appears on the screen.
45
Menu Opon Descripon
OSD Pivot
Set the OSD Menu orientaon.
• Auto: With the built-in G sensor, the OSD Menu can
automacally pivot when the monitor is posioned
vercally.
• 0°: Sets the OSD Menu without a pivot.
• +90°: Sets the OSD Menu with a +90° pivot.
• -90°: Sets the OSD Menu with a -90° pivot.
• 180°: Sets the OSD Menu with a 180° pivot.
Power Indicator
Set the Power Indicator On or O. If the seng is set to On,
the power indicator lights blue when the device is turned
on.
Auto Power O Enable this opon to allow the monitor to automacally
turn o aer a certain amount of me.
Sleep Set the amount of idle me before the monitor enters Sleep
mode.
Mul-Picture
O
Disable this funcon.
PBP Le-Right
Display two windows, a 1x1 split screen, side-by-side on
the le and right of the screen. User can specify the input
source for each screen.
PIP
Split the screen into two parts, a main window and an inset
window. User can specify the input source for each screen.
Dual Color
Display two dierent color sengs in PIP or PBP mode.
ECO Mode Choose between various modes, based on power
consumpon.
Overscan
Enable this opon to automacally enlarge the original
picture horizontally and vercally to an equal aspect rao
that lls the screen.
46
Menu Opon Descripon
Response Time
Adjust the response me, creang smooth images without
streaking, blurring or ghosng. A low response me is
perfect for the most graphic-intense gaming, and provides
amazing visual quality while watching sports or acon
movies.
USB Charging Enable/disable usb charging.
Backstage Lighng Adjust the LED lighng.
Burn-in Eraser Reduce image burn-in.
DDC/CI Enable this opon to allow the monitor control via the
graphics card.
Rename Rename the personalized custom prole.
All Recall Resets all sengs to their default values.
47
Advanced Features and Sengs
HDR (High-Dynamic-Range)
Reduces the overall contrast of a given scene so that detail in the highlights and
shadows can be seen.
NOTE: Ensure the HDR seng is turned on on your device rst before enabling
the HDR10 on the monitor. For example, the HDR seng on Xbox One S
or PS4 Pro needs to be turned on rst before enjoying your HDR10 video
content.
Xbox One S PS4 Pro
To enable the HDR funcon:
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Color Mode. Then press the l key to enter the
Color Mode menu.
3. Move the joy key p or q to select HDR. Then press the l key to enter its sub-
menu.
4. Move the joy key p or q to select one of the opons . Then press the l key to
conrm.
4848
KVM
The KVM funcon allows the user to control two computers connected to the same
monitor from a single keyboard and mouse.
NOTE: Only applicable in PBP (Picture-by-Picture) mode.
To connect the two computers to the monitor:
1. Connect one end of the USB Type C cable to the USB Type C port of the monitor.
Then connect the other end of the cable to the USB Type C port of the notebook.
2. Connect one end of a DisplayPort cable to the DisplayPort of the monitor. Then
connect the other end of the cable to the DisplayPort or mini DP of the computer.
3. Connect the USB Type B male cable (square with 2 cut corners) to the USB Type B
port of the monitor. Then connect the other end of the cable to the USB port of
the computer.
Type-C
Type-C
Micro USB
5V/3A
4949
To enable PBP mode:
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select the Setup Menu menu. Then press the l key
to enter the menu.
3. Move the joy key p or q to select Multi-Picture. Then press the l key to enter
its sub-menu.
4. Move the joy key p or q to select PBP Left-Right. Then press the l key to enable
PBP mode.
To acvate the KVM funcon:
1. Press and hold the u key for two (2) seconds to acvate the KVM funcon.
2. Then you will be able to switch the cursor between the two screens (le/right
window).
5050
Auto Pivot
With the Auto Pivot funcon, the monitor can detect the image display and adjust
the image’s orientaon on the screen automacally when pivong the screen
vercally or horizontally.
NOTE: The Auto Pivot funcon uses DDC/CI to communicate with the monitor.
Before applying the Auto Pivot funcon, please make sure the DDC/CI
seng is set to On.
To enable the DDC/CI seng:
1. Open the OSD Menu and select the Setup Menu menu. Then press the l key to
enter the menu.
2. Move the joy key p or q to select DDC/CI. Then press the l key to enter its sub-
menu.
3. Move the joy key p or q to select On. Then press the l key to confirm.
Aer ensuring DDC/CI is On, proceed to set OSD Pivot to Auto:
1. Open the OSD Menu and select the Setup Menu menu. Then press the l key to
enter the menu.
2. Move the joy key p or q to select OSD Pivot. Then press the l key to enter its
sub-menu.
3. Move the joy key p or q to select Auto. Then press the l key to conrm.
5151
Colorbraon+
To ensure long-term color accuracy, some specic models support the hardware
color calibraon funcon. The Colorbraon+ applicaon installaon le can be
found at: hp://color.viewsonic.com/support/soware/.
Standard monitor packing does not include the color sensor, which the
Colorbraon+ applicaon needs for the calibraon process.
Compable color sensors include:
• X-Rite i1 Display Pro
• X-Rite i1 Pro 2
• X-Rite i1 Studio
• Xrite Colormunki Photo
• Xrite Colormunki Design
• Datacolor Spyder 5
• Datacolor SpyderX series
5252
Dual Color
The monitor comes with a dual color engine to display two dierent color sengs
in PIP (Picture-in-Picture) or PBP mode. You can set dierent color presets in both
windows (Main Window and Secondary Window).
Main Window Secondary Window
NOTE: To enable PIP or PBP mode, refer to the “Mul-Picture” secon.
To congure Dual Color:
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select the Setup Menu menu. Then press the l key
to enter the menu.
3. Move the joy key p or q to select Multi-Picture. Then press the l key to enter
its sub-menu.
4. Move the joy key p or q to select Dual Color. Then press the l key to enter its
sub-menu.
5. Move the joy key p or q to select the desired color setting. Then press the l key
to confirm.
5353
Mul-Picture
Mul-Picture allows users to further customize their work space by allowing up to
four split windows from dierent inputs, displaying high resoluon content with
dierent aspect raos, without distoron from the original input sources.
To enable Mul-Picture mode:
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Color Mode. Then press the l key to enter the
Color Mode menu.
3. Move the joy key p or q to select Multi-Picture. Then press the l key to enter
its sub-menu.
4. Move the joy key p or q to select PBP Left-Right or PIP. Then press the l key to
enter the selected mode.
5454
PBP (Picture-by-Picture)
Le Window Right Window
PBP Le-Right
NOTE: To display full-sized images in the windows, please adjust the screen
resoluon to ###### (PBP Le-Right).
To congure PBP:
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Setup Menu. Then press the l key to enter
the Setup Menu menu.
3. Move the joy key p or q to select Multi-Picture. Then press the l key to enter
its sub-menu.
4. Move the joy key p or q to select PBP Left-Right. Then press the l key to enter
its sub-menu.
5. To change the input source, select the source locaon (Le Source Select/Right
Source Select) and press the l key.
6. Move the joy key p or q to select the desired input source and press the l key
to conrm.
7. To swap the two windows, select Swap and press the l key to conrm.
5555
PIP (Picture-in-Picture)
Main Window
Inset Window
To congure PIP:
1. Move the joy key t to display the Startup Menu. Then navigate to Main Menu
and press the l key to display the OSD Menu.
2. Move the joy key p or q to select Setup Menu. Then press the l key to enter
the Setup Menu menu.
3. Move the joy key p or q to select Multi-Picture. Then press the l key to enter
its sub-menu.
4. Move the joy key p or q to select PIP. Then press the l key to enter its sub-
menu.
5. To change the input source for the Inset Window, select PIP Source Select and
press the l key. Then move the joy key p or q to select the desired input source
and press the l key to conrm.
6. To adjust the Inset Window posion, select PIP Posion and press the l key.
Press the l key to select PIP H.Posion or PIP V.Posion.
Move the joy key p or q to adjust the seng and press the l key to
conrm.
7. To adjust the Inset Window size, select PIP Size and press the l key. Then move
the joy key p or q to adjust the seng.
8. To swap the two windows, select Swap and press the l key to conrm.
5656
Backstage Lighng
With the Backstage Lighng funcon, the monitor can adjust the LED brightness to
the opmal sengs.
To congure the Backstage Lighng sengs:
1. Open the OSD Menu and select the Setup Menu menu. Then touch the l key to
enter the menu.
2. Move the joy key p or q to select Backstage Lighng. Then touch the l key to
enter its sub-menu.
3. Move the joy key p or q to select Level 1, Level 2, or Level 3 to enable the
funcon. Then touch the l key to conrm.
57
Firmware Update
For the best display performance and to resolve any known issues, it is best to keep
your monitor updated with the latest rmware version. With the supplied USB
cable and the vDisplayManager applicaon, you can easily update your monitor’s
rmware.
To update the rmware:
1. Download and install the vDisplayManager application: hps://color.viewsonic.
com/support/soware/.
2. Connect the USB Type B male cable (square with 2 cut corners) to the USB Type B
port of your monitor. Then connect the other end of the cable to the USB port of
the computer.
Micro USB
5V/3A
3. Launch vDisplayManager. Select the Advanced tab in the side menu.
4. Click Update to check for any updates to your monitor’s firmware.
5. Wait unl the update process is complete (if applicable).
NOTE: Any interrupons during the rmware update process may permanently
damage your monitor. Do not disconnect the USB cable or turn o your
PC and monitor.
5858
Appendix
Specicaons
Item Category Specicaons
LCD Type IPS type, TFT Acve Matrix 2560 x 1440 LCD,
0.2331 mm x 0.2331 mm pixel pitch
Display Size 68.47 cm, 27" (27" viewable)
Color Filter RGB vercal stripe
Glass Surface Anti-Glare type, Hard Coang (3H)
Input Signal Video Sync TMDS digital (100 Ω)
HDMI: fh:15-204 kHz, fv:24-120 Hz
DisplayPort: fh:15-204 kHz, fv:24-120 Hz
Compability PC up to 2560 x 1440
Macintosh up to 2560 x 1440
Recommended 2560 x 1440 @ 165Hz
Resoluon1Supported • 2560 x 1440 @ 60, 165Hz
• 2048 x 1152 @ 60Hz
• 1920 x 1440 @ 60Hz
• 1920 x 1200 @ 60Hz
• 1920 x 1080 @ 50, 60Hz
• 1680 x 1050 @ 60Hz
• 1600 x 1200 @ 60Hz
• 1600 x 900 @ 60Hz
• 1440 x 900 @ 60, 75Hz
• 1400 x 1050 @ 60, 75Hz
• 1366 x 768 @ 60Hz
• 1360 x 768 @ 60Hz
• 1280 x 1024 @ 50, 60, 75Hz
• 1280 x 960 @ 50, 60, 75Hz
• 1280 x 800 @ 60Hz
• 1280 x 768 @ 50, 60Hz
• 1280 x 720 @ 50, 60Hz
• 1152 x 900 @ 67Hz
• 1152 x 864 @ 75Hz
• 1024 x 768 @ 50, 60, 70, 72, 75Hz
• 848 x 480 @ 60Hz
• 800 x 600 @ 56, 60, 72Hz
• 720 x 576 @ 50Hz
• 720 x 480 @ 60Hz
• 720 x 400 @ 70Hz
• 640 x 480 @ 50, 60, 67, 72Hz
• 640 x 400 @ 60, 70Hz
• 640 x 350 @ 70Hz
Power Adapter2Input Voltage AC 100-240V, 50/60Hz (auto switch)
59
Item Category Specicaons
Display Area Full Scan (H x V) 596.74 x 335.66 mm (23.49” x 13.21”)
Operang
condions
Temperature 0° C to 40° C (32° F to 104° F)
Humidity 20% to 90% (non-condensing)
Altude 10,000 feet (3.048 km)
Storage
condions
Temperature -20° C to 60° C (-4° F to 140° F)
Humidity 5% to 90% (non-condensing)
Altude 40, 000 feet (12.1 km)
Dimensions Physical
(W x H x D)
613.70 x 569.36~449.36 x 234 mm
(24.16” x 22.42~17.69” x 9.21”)
Wall Mount Dimensions 100 x 100 mm
Weight Physical 9.55 kg (21.05 lbs)
Power saving
modes
On332W (Typical)
O < 0.3W (Max)
1 Do not set the graphics card in your computer to exceed these ming modes; doing so may result in permanent damage to the display.
2 Please use the power adapter from ViewSonic® or an authorized source only.
3 The test condion follows EEI standards.
60
Glossary
This secon describes the standard glossary of terms used in all LCD display models.
All terms are listed in alphabecal order.
NOTE: Some terms may not be applicable to your monitor.
AAdvanced DCR
Advanced DCR technology automacally detects the image signal and
intelligently controls the backlight brightness and color to improve on the
ability to make the black blacker in a dark scene, and make the white whiter
in a bright environment.
Adapve Sync
Adapve Sync technology puts an end to choppy gameplay and broken
frames with uid, arfact-free performance at virtually any frame rate.
Audio Adjust
Adjusts the volume, mutes the sound, or toggles between inputs if you have
more than one source.
Auto Detect
If the current input source has no signal, the monitor will automacally
switch to the next input opon. This funcon, on some models, is disabled
by default.
BBlack Stabilizaon
ViewSonic’s Black Stabilizaon provides heightened visibility and detail by
brightening dark scenes.
Blue Light Filter
Adjusts the lter that blocks high-energy blue light for a more comfortable
viewing experience.
Boot Up Screen
Turning o the boot screen will disable the on-screen message from
displaying when turning on the monitor.
Brightness
Adjusts background black levels of the screen image.
61
CColor Adjust
Provides several color adjustment modes to help adjust the color sengs to
t the user’s needs.
Color Range
The monitor can detect the input signal color range automacally. You can
manually change the color range opons to t the correct color range if the
colors are not displayed correctly.
Opons Descripon
Auto The monitor automacally recognizes the color format and
black and white levels.
Full Range The color range of the black and white levels are full.
Limited Range The color range of the black and white levels are limited.
Color Space
Allows users to choose which color space they would like to use for monitor
color output (RGB, YUV).
Color Temperature
Allows users to select specic color temperature sengs to further
customize their viewing experience.
Panel Default Panel Original Status
sRGB Standard color space used for the Windows system.
Bluish Set the color temperature to 9300K.
Cool Set the color temperature to 7500K.
Nave Default color temperature. Recommended for general use.
Warm Set the color temperature to 5000K.
Contrast
Adjusts the dierence between the image background (black level) and the
foreground (white level).
GGamma
Allows users to manually adjust the brightness level of the monitor’s
grayscale levels. There are six selecons: 1.8, 2.0, 2.2, 2.4, 2.6, and 2.8.
HHue
Adjusts the nt of each color (red, green, blue, cyan, magenta, and yellow).
62
IInformaon
Displays the ming mode (video signal input) coming from the graphics
card in the computer, the LCD model number, the serial number, and the
ViewSonic® website URL. See your graphics card’s user guide for instrucons
on changing the resoluon and refresh rate (vercal frequency).
NOTE: VESA 1024 x 768 @ 60Hz, for example, means that the resoluon
is 1024 x 768 and the refresh rate is 60Hz.
Input Select
Toggles between the various input opons that are available for the
monitor.
MManual Image Adjust
Displays the “Manual Image Adjust” menu. You can manually set a variety of
image quality adjustments.
Memory Recall
Returns the adjustments back to factory sengs if the display is operang in
a factory preset ming mode listed in the “Specicaons” of this manual.
NOTE:
• (Excepon) This control does not aect changes made in the
“Language Select” or “Power Lock” seng.
• Memory Recall is the default as-shipped display conguraon and
sengs. Memory Recall is the seng in which the product qualies
for ENERGY STAR®. Any changes to default as-shipped display
conguraon and sengs would change the energy consumpon,
and may increase energy consumpon beyond the limits required
for ENERGY STAR® qualicaon, as applicable. ENERGY STAR® is a
set of power-saving guidelines issued by the U.S. Environmental
Protecon Agency (EPA). ENERGY STAR® is a joint program of the
U.S. Environmental Protecon Agency
and the U.S. Department of Energy helping us all save
money and protect the environment through energy
ecient products and pracces.
63
OOset
Adjusts black levels for red, green, and blue. The gain and oset funcons
allow users to control the white balance for the upmost control when
manipulang contrast and dark scenes.
OSD Pivot
Sets the monitor OSD Menu display direcon.
Overscan
Refers to a cropped image on your monitor’s screen. A seng on your
monitor zooms in on movie content, so that you cannot see the outermost
edges of the lm.
PPower Indicator
The light that displays whether the monitor is on or o. This seng also
controls the lighng on the stand. Users can turn o the lighng eect
under “Power Indicator”. Addionally, the power indicator displays an
average color directly interpreng the input color signal received on screen.
QQuick Access
Quickly iniate some funcons and modes through the Quick Access key
and menu. Users can also dene which funcons or modes they prefer in
the Quick Access Menu via the Setup Menu in OSD. The funcon/mode will
be enabled as soon as the light-bar moves on the item, and will disable aer
removing the light-bar.
RRecall
Resets the ViewMode monitor sengs.
Resoluon Noce
The noce tells users that the current viewing resoluon is not the correct
nave resoluon. This noce will appear in the display sengs window
when seng up the display resoluon.
64
SSetup Menu
Adjusts On-Screen Display (OSD) Menu sengs. Many of these sengs can
acvate on-screen display nocaons so users do not have to reopen the
menu.
Sharpness
Adjusts the picture quality of the monitor.
VViewMode
ViewSonic’s unique ViewMode feature oers “Game”, “Movie”, “Web”,
“Text”, “MAC”, and “Mono” presets. These presets are specically designed
to deliver an opmized viewing experience for dierent screen applicaons.
ViewScale
Gamers have the ability to adjust the display size of the image on the
monitor, allowing for a “best t” scenario.
65
Troubleshoong
This secon describes some common problems that you may experience when
using the monitor.
Problem or Issue Possible Soluons
No power • Make sure you have turned on the monitor by
pressing the Power buon.
• Make sure the power cord is properly and securely
connected to the monitor and power outlet.
• Plug another electrical device into the power outlet
to verify that the outlet is supplying power.
Power is On, but no
image appears on
screen
• Make sure the video cable connecng the
monitor to the computer is properly and securely
connected.
• Adjust the brightness and contrast sengs.
• Make sure the correct input source is selected.
Wrong or abnormal
colors
• If any colors (red, green, or blue) are missing,
check the video cable to make sure it is properly
and securely connected. Loose or broken pins
in the cable connector could cause an improper
connecon.
• Connect the monitor to another computer.
• If you have an older graphics card, contact
ViewSonic® for a non-DDC adapter.
Screen image is too
light or dark
• Adjust brightness and contrast sengs via the OSD
Menu.
• Reset the monitor to factory sengs.
Screen image cuts in
and out
• Make sure the correct input source is selected.
• Check for bent or broken pins in the video cable
connector.
• Make sure the video cable connecng the
monitor to the computer is properly and securely
connected.
Screen image is
blurred
• Adjust the resoluon to the correct Aspect Rao.
• Reset the monitor to factory sengs.
66
Problem or Issue Possible Soluons
The screen isn’t
centered correctly
• Adjust the horizontal and vercal controls via the
OSD Menu.
• Check the Aspect Rao.
• Reset the monitor to factory sengs.
The screen appears
yellow
• Make sure the “Blue Light Filter” is O.
The OSD Menu
does not appear
on the screen/the
OSD controls are
inaccessible
• Check whether the OSD Menu is locked.
• Turn o the monitor, unplug the power cord, plug it
back in, and then turn on the monitor.
• Reset the monitor to factory sengs.
Control panel keys do
not work
• Press only one key at a me.
• Restart the computer.
Some menus aren’t
selectable in the OSD
• Adjust the ViewMode or the input source.
• Reset the monitor to factory sengs.
No audio output • If using ear-/headphones, ensure the mini stereo
jack is connected.
• Make sure the volume is not muted, nor set to 0.
• Check the Audio Input seng.
The monitor will not
adjust
• Make sure there are no obstrucons near or on the
monitor, and that there is adequate spacing.
• For more informaon, see “Adjusng the Viewing
Angle”.
USB devices connected
to the monitor do not
work
• Make sure the USB cable is connected properly.
• Try changing to another USB port (if applicable).
• Some USB devices require a higher electric current;
connect the device directly to the computer.
The external device
is connected, but no
image appears on the
screen
• Make sure the Power is On
• Adjust brightness and contrast via the OSD Menu.
• Check the connecng cable and make sure it
is properly and securely connected. Loose or
broken pins in the cable connector could cause an
improper connecon.
67
Maintenance
General Precauons
• Make sure the monitor is turned o and the power cable is unplugged from the
power outlet.
• Never spray or pour any liquid directly onto the screen or case.
• Handle the monitor with care, as a darker-colored monitor, if scued, may show
marks more clearly than a lighter-colored monitor.
Cleaning the Screen
• Wipe the screen with a clean, so, lint-free cloth. This removes dust and other
parcles.
• If the screen is sll not clean, apply a small amount of non-ammonia, non-
alcohol based glass cleaner onto a clean, so, lint-free cloth; then wipe the
screen.
Cleaning the Case
• Use a so, dry cloth.
• If the case is sll not clean, apply a small amount of non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, so, lint-free cloth, then wipe
the surface.
Disclaimer
• ViewSonic® does not recommend the use of any ammonia or alcohol-based
cleaners on the display screen or case. Some chemical cleaners have been
reported to damage the screen and/or case of the monitor.
• ViewSonic® will not be liable for damage resulng from use of any ammonia or
alcohol-based cleaners.
68
Regulatory and Service Informaon
Compliance Informaon
This secon addresses all connected requirements and statements regarding
regulaons. Conrmed corresponding applicaons shall refer to nameplate labels
and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operaon is subject to the following
two condions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operaon. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protecon against harmful
interference in a residenal installaon. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance
with the instrucons, may cause harmful interference to radio communicaons.
However, there is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to radio or television
recepon, which can be determined by turning the equipment o and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separaon between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cauoned that changes or modicaons not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
Industry Canada Statement
CAN ICES-003 (B)/NMB-003(B)
CE Conformity for European Countries
The device complies with the EMC Direcve 2014/30/EU and Low Voltage
Direcve 2014/35/EU.
69
The following informaon is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical
and Electronic Equipment Directive 2012/19/EU (WEEE). The mark
indicates the requirement NOT to dispose of the equipment as unsorted
municipal waste, but use the return and collection systems according to
local law.
Declaraon of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direcve
2011/65/EU of the European Parliament and the Council on restricon of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Direcve) and is deemed to comply with the maximum concentraon values issued
by the European Technical Adaptaon Commiee (TAC) as shown below:
Substance Proposed Maximum
Concentraon Actual Concentraon
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6⁺) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE) 0.1% < 0.1%
Bis (2-ethylhexyl) phthalate
(DEHP) 0.1% < 0.1%
Butyl benzyl phthalate (BBP) 0.1% < 0.1%
Dibutyl phthalate (DBP) 0.1% < 0.1%
Diisobutyl phthalate (DIBP) 0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex
III of the RoHS2 Direcves as noted below. Examples of exempted components
are:
• Lead as an alloying element in aluminum containing up to 0.4% lead by weight.
• Copper alloy containing up to 4% lead by weight.
• Lead in high melng temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
• Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
70
Indian Restricon of Hazardous Substances
Restricon on Hazardous Substances statement (India). This product complies
with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent
chromium, polybrominated biphenyls or polybrominated diphenyl ethers in
concentraons exceeding 0.1 weight % and 0.01 weight % for cadmium, except for
the exempons set in Schedule 2 of the Rule.
Product Disposal at End of Product Life
ViewSonic® respects the environment and is commied to working and living
green. Thank you for being part of Smarter, Greener Compung. Please visit the
ViewSonic® website to learn more.
USA & Canada:
http://www.viewsonic.com/company/green/recycle-program/
Europe:
http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan:
https://recycle.epa.gov.tw/
71
Copyright Informaon
Copyright© ViewSonic® Corporaon, 2021. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microso, Windows, and the Windows logo are registered trademarks of Microso
Corporaon in the United States and other countries.
ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are
registered trademarks of ViewSonic® Corporaon.
VESA is a registered trademark of the Video Electronics Standards Associaon.
DPMS, DisplayPort, and DDC are trademarks of VESA.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protecon
Agency (EPA).
As an ENERGY STAR® partner, ViewSonic® Corporaon has determined that this
product meets the ENERGY STAR® guidelines for energy eciency.
Disclaimer: ViewSonic® Corporaon shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequenal damages
resulng from furnishing this material, or the performance or use of this product.
In the interest of connuing product improvement, ViewSonic® Corporaon
reserves the right to change product specicaons without noce. Informaon in
this document may change without noce.
No part of this document may be copied, reproduced, or transmied by any means,
for any purpose without prior wrien permission from ViewSonic® Corporaon.
VP2776_UG_ENG_Rev. 1A_2021-07-02
72
Customer Service
For technical support or product service, see the table below or contact your
reseller.
NOTE: You will need the product’s serial number.
Country/ Region Website Country/ Region Website
Asia Pacic & Africa
Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/
中国 (China) www.viewsonic.com.cn 香港 (繁體中文) www.viewsonic.com/hk/
Hong Kong (English) www.viewsonic.com/hk-en/ India www.viewsonic.com/in/
Indonesia www.viewsonic.com/id/ Israel www.viewsonic.com/il/
日本 (Japan) www.viewsonic.com/jp/ Korea www.viewsonic.com/kr/
Malaysia www.viewsonic.com/my/ Middle East www.viewsonic.com/me/
Myanmar www.viewsonic.com/mm/ Nepal www.viewsonic.com/np/
New Zealand www.viewsonic.com/nz/ Pakistan www.viewsonic.com/pk/
Philippines www.viewsonic.com/ph/ Singapore www.viewsonic.com/sg/
臺灣 (Taiwan) www.viewsonic.com/tw/ ประเทศไทย www.viewsonic.com/th/
Việt Nam www.viewsonic.com/vn/ South Africa & Maurius www.viewsonic.com/za/
Americas
United States www.viewsonic.com/us Canada www.viewsonic.com/us
Lan America www.viewsonic.com/la
Europe
Europe www.viewsonic.com/eu/ France www.viewsonic.com/fr/
Deutschland www.viewsonic.com/de/ Қазақстан www.viewsonic.com/kz/
Россия www.viewsonic.com/ru/ España www.viewsonic.com/es/
Türkiye www.viewsonic.com/tr/ Україна www.viewsonic.com/ua/
United Kingdom www.viewsonic.com/uk/
73
Limited Warranty
ViewSonic® Display
What the warranty covers:
ViewSonic® warrants its products to be free from defects in material and
workmanship during the warranty period. If a product proves to be defecve
in material or workmanship during the warranty period, ViewSonic® will, at its
sole opon, and as your sole remedy, repair or replace the product with a similar
product. Replacement Product or parts may include remanufactured or refurbished
parts or components. The repair or replacement unit or parts or components will
be covered by the balance of the me remaining on the customer’s original limited
warranty and the warranty period will not be extended. ViewSonic® provides
no warranty for any third-party soware whether included with the product or
installed by the customer, installaon of any unauthorized hardware parts or
components (e.g. Projector Lamps). (Please refer to: “What the warranty excludes
and does not cover” secon).
How long the warranty is eecve:
ViewSonic® displays are warranted for between 1 and 3 years, depending on your
country of purchase, for all parts including the light source and for all labor from
the date of the rst consumer purchase.
Who the warranty protects:
This warranty is valid only for the rst consumer purchaser.
What the warranty excludes and does not cover:
• Any product on which the serial number has been defaced, modied, or
removed.
• Damage, deterioraon, or malfuncon resulng from:
Accident, misuse, neglect, re, water, lightning, or other acts of nature,
unauthorized product modicaon, or failure to follow instrucons supplied
with the product.
Repair or aempted repair by anyone not authorized by ViewSonic®.
Damage to or loss of any programs, data, or removable storage media.
Normal wear and tear.
Removal or installaon of the product.
• Soware or data loss occurring during repair or replacement.
• Any damage of the product due to shipment.
74
• Causes external to the product, such as electric power uctuaons or failure.
• Use of supplies or parts not meeng ViewSonic’s specicaons.
• Failure of owner to perform periodic product maintenance as stated in the User
Guide.
• Any other cause which does not relate to a product defect.
• Damage caused by stac (non-moving) images displayed for lengthy periods of
me (also referred to as image burn-in).
• Soware - Any third-party soware included with the product or installed by the
customer.
• Hardware/Accessories/Parts/Components – Installaon of any unauthorized
hardware, accessories, consumable parts or components (e.g. Projector Lamps).
• Damage to, or abuse of, the coang on the surface of the display through
inappropriate cleaning as described in the product User Guide.
• Removal, installaon, and set-up service charges, including wall-mounng of the
product.
How to get service:
• For informaon about receiving service under warranty, contact ViewSonic®
Customer Support (Please refer to the “Customer Service” page). You will need
to provide your product’s serial number.
• To obtain warranty service, you will be required to provide: (a) the original dated
sales slip, (b) your name, (c) your address, (d) a descripon of the problem, and
(e) the serial number of the product.
• Take or ship the product, freight prepaid, in the original container to an
authorized ViewSonic® service center or ViewSonic®.
• For addional informaon or the name of the nearest ViewSonic® service center,
contact ViewSonic®.
Limitaon of implied warranes:
There are no warranes, express or implied, which extend beyond the descripon
contained herein including the implied warranty of merchantability and tness for a
parcular purpose.
75
Display Warranty Term Template In UG
VSC_TEMP_2007
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic® shall not be liable for:
• Damage to other property caused by any defects in the product, damages
based upon inconvenience, loss of use of the product, loss of me, loss of
prots, loss of business opportunity, loss of goodwill, interference with business
relaonships, or other commercial loss, even if advised of the possibility of such
damages.
• Any other damages, whether incidental, consequenal or otherwise.
• Any claim against the customer by any other party.
• Repair or aempted repair by anyone not authorized by ViewSonic®.
Eect of state law:
This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state. Some states do not allow limitaons on implied
warranes and/or do not allow the exclusion of incidental or consequenal
damages, so the above limitaons and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty informaon and service on ViewSonic® products sold outside of the
U.S.A. and Canada, contact ViewSonic® or your local ViewSonic® dealer.
The warranty period for this product in mainland China (Hong Kong, Macao,
and Taiwan Excluded) is subject to the terms and condions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found at:
http://www.viewsonic.com/eu/ under “Support/Warranty Informaon”.
76
Mexico Limited Warranty
ViewSonic® Display
What the warranty covers:
ViewSonic® warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product
proves to be defecve in material or workmanship during the warranty period,
ViewSonic® will, at its sole opon, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or
components & accessories.
How long the warranty is eecve:
ViewSonic® LCD displays are warranted for between 1 and 3 years, depending on
your country of purchase, for all parts including the light source and for all labour
from the date of the rst consumer purchase.
Who the warranty protects:
This warranty is valid only for the rst consumer purchaser.
What the warranty excludes and does not cover:
• Any product on which the serial number has been defaced, modied or
removed.
• Damage, deterioraon, or malfuncon resulng from:
Accident, misuse, neglect, re, water, lightning, or other acts of nature,
unauthorized product modicaon, unauthorized aempted repair, or
failure to follow instrucons supplied with the product.
Causes external to the product, such as electrical power uctuaons or
failure.
Use of supplies or parts not meeng ViewSonic®’s specicaons.
Normal wear and tear.
Any other cause which does not relate to a product defect.
• Any product exhibing a condion commonly known as “image burn-in” which
results when a stac image is displayed on the product for an extended period of
me.
• Removal, installaon, insurance, and set-up service charges.
77
How to get service:
For informaon about receiving service under warranty, contact ViewSonic®
Customer Support (Please refer to the aached “Customer Service” page). You
will need to provide your product’s serial number, so please record the product
informaon in the space provided below on your purchase for your future use.
Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: Model Number:
Document Number: Serial Number:
Purchase Date: Extended Warranty Purchase? (Y/N)
If so, what date does warranty expire?
• To obtain warranty service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a descripon of the problem, and
(e) the serial number of the product.
• Take or ship the product, in the original container packaging, to an authorized
ViewSonic® service center.
• Round trip transportaon costs for in-warranty products will be paid by
ViewSonic®.
Limitaon of implied warranes:
There are no warranes, express or implied, which extend beyond the descripon
contained herein including the implied warranty of merchantability and tness for a
parcular purpose.
Exclusion of damages:
ViewSonic®’s liability is limited to the cost of repair or replacement of the product.
ViewSonic® shall not be liable for:
• Damage to other property caused by any defects in the product, damages
based upon inconvenience, loss of use of the product, loss of me, loss of
prots, loss of business opportunity, loss of goodwill, interference with business
relaonships, or other commercial loss, even if advised of the possibility of such
damages.
• Any other damages, whether incidental, consequenal or otherwise.
• Any claim against the customer by any other party.
• Repair or aempted repair by anyone not authorized by ViewSonic®.
78
Contact Informaon for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporavo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 hp://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Villahermosa:
Compumantenimietnos Garanzados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av.
Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Chihuahua:
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Cuernavaca:
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Guerrero Acapulco:
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembr
Tijuana, Mexico
FOR USA SUPPORT:
ViewSonic® Corporaon
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688
E-Mail: hp://www.viewsonic.com
LCD Mexico Warranty Term Template In UG
VSC_TEMP_2008
C0 M91 Y72 K24
Process Color
C0 M0 Y0 K100
Process Color
C0 M91 Y72 K24
Process Color
Pantone Black C
Spot Color
Pantone 187 C
Spot Color
Pantone Black C
Spot Color
Pantone 187 C
Or Spot Color