Whirlpool ACE010IX User Manual
Displayed below is the user manual for ACE010IX by Whirlpool which is a product in the Coffee Makers category. This manual has pages.
Related Manuals
1
ACE 010
www.whirlpool.com
2
INSTALLATION
PRIOR TO CONNECTING
ENSURE THAT THE APPLIANCE IS NOT DAMAGED.
AFTER CONNECTING
THE EARTHING OF THIS APPLIANCE is compulso-
ry. The manufacturer will accept no re-
sponsibility for injury to persons, ani-
mals or damage to objects arising from
the non-observance of this requirement.
The manufacturers are not liable for any
problems caused by the user’s failure to ob-
serve these instructions.
DO NOT OPERATE THIS APPLIANCE if it has a
damaged mains cord or plug, if it is not
working properly, or if it has been dam-
aged or dropped. Do not immerse the
mains cord or plug in water. Keep the
cord away from hot surfaces. Electrical
shock, fi re or other hazards may result.
CHECK THAT THE VOLTAGE on the rating
plate corresponds to the voltage in your
home.
MOUNTING THE APPLIANCE
FOLLOW THE SUPPLIED separate mounting in-
structions when installing the appliance.
THIS APPLIANCE IS DESIGNED TO WORK
in ambient temperatures above
freezing point of water (0°C).
If residual water is allowed to
freeze, the appliance may be
damaged.
3
IMPORTANT SAFETY INSTRUCTIONS
DO NOT HEAT, OR USE FLAMMABLE LIQUIDS in or
near the appliance. Fumes can create a
fi re hazard or explosion.
DO NOT LEAVE THE APPLIANCE UNATTENDED
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
ONLY ALLOW CHILDREN to use the appliance
without adult supervision after adequate
instructions have been given, so that the
child is able to use the appliance in a safe
way and understands the hazards of im-
proper use.
The appliance is not intended for use by
young children or infirm persons without
supervision. Young children should be su-
pervised to ensure that they do not play
with the appliance.
Children should only use the appliance un-
der adult supervision due to the high tem-
peratures generated.
DO NOT USE corrosive chemicals or vapors
in this appliance. This type of appliance
is specifi cally designed to heat water. It
is not designed for industrial or labora-
tory use.
THIS APPLIANCE IS DESIGNED FOR DOMESTIC USE ONLY!
PRECAUTIONS
USE HOT PADS OR OVEN MITTS to prevent
burns, when touching hot parts.
THIS APPLIANCE IS DESIGNED TO MAKE COFFEE or heat
drinks. Be careful to avoid being scalded by
sprays of water or steam or due to improper
use of the appliance.
4
ACCESSORIES & PARTS
q CONTROL PANEL
w STEAM KNOB
e WATER TANK
r POWER CABLE
t STEAM/HOT WATER TUBE
y DRIP MESH
u DRIP TRAY
i CAPPUCCINO MAKER
o NOZZLE
a BOILER OUTLET
s PRESSER
d FILTER HOLDER
1# LARGE TWO-CUP FILTER
g SMALL ONE-CUP OR POD FILTER
h STEAM SELECTOR BUTTON
j COFFEE/HOT WATER BUTTON
k ON/OFF BUTTON
l ON LIGHT
1( TEMPERATURE OK LIGHT (COFFEE
OR HOT WATER)
2) STEAM INDICATOR LIGHT
2! LIGHT SWITCH
qw
e
r
t
y
u
i
o
a
s
d
f
g
h
j
kl1(
2)
2!
5
1
2
FILLING THE WATER TANK
1. TURN THE APPLIANCE on by pressing the ON/OFF
BUTTON AND ATTACH THE FILTER HOLDER TO THE APPLI-
ANCE WITHOUT ADDING GROUND COFFEE.
q REMOVE THE WATERTANK by pulling it out (to-
wards the front).
NEVER USE THE APPLIANCE WITHOUT WATER IN
THE TANK and always remember to top up
when the level drops to a couple of cen-
timetres from the bottom.
w FILL THE TANK with fresh
clean water taking care
not to exceed the MAX
level. Refi t the tank.
PREHEATING THE COFFEE UNIT
TO ATTACH THE FILTER HOLDER, position it under the
boiler outlet
with the han-
dle towards
the left,
push it
upwards
and at the
same time rotate the
handle fi rmly towards the right.
Check that the steam knob is closed.
2. PLACE A CUP UNDER THE FILTER HOLDER. Use the
same cup as will be used to prepare the coff ee
in order to preheat it.
3. WAIT FOR THE OK INDICATOR
LIGHT to come on, then imme-
diately press the coff ee knob.
Run the water off until the OK
indicator light goes out, then inter-
rupt delivery by pressing the coff ee
button again.
4. EMPTY THE CUP. Wait until the OK
indicator light comes on again then repeat the
same operation. (It is normal for a small and
harmless puff of steam to be given off when
removing the fi lter holder).
6
1
2
1. AFTER PREHEATING the appliance as described
above, place the ground coff ee fi lter
in the fi lter holder, making sure the
projection is correctly inserted in
the slot. Use the smaller fi lter to
make one coff ee or the larg-
er fi lter to make two coff ees.
HOW TO PREPARE ESPRESSO COFFEE USING THE
FILTER HOLDER FOR GROUND COFFEE
2. TO MAKE A SINGLE COFFEE ONLY, place one level
measure (about 7 g) of ground cof-
fee in the fi lter. To prepare two cof-
fees, place two loosely fi lled
measures (about 6+6 g)
of ground coff ee in the fi l-
ter. Fill the fi lter a little at a time to prevent the
ground coff ee from overfl owing.
IMPORTANT: for correct operation, before
adding the ground coff ee to the fi lter holder,
clean the fi lter from residues of ground coff ee
from the previous infusion.
5. PLACE THE CUP or cups under the fi lter holder
spouts.
You are rec-
ommended to
heat the cups
before mak-
ing the cof-
fee by rinsing
them with a little
hot water.
6. MAKE SURE THE OK LIGHT IS ON
(if off , wait until it comes on),
then press the coff ee button.
When the required quantity of
coff ee has been run off , press
the same button again. (You should
not run off coff ee for more than 45
seconds at a time).
7. TO REMOVE THE FILTER HOLDER, rotate the handle
from right to left.
IMPORTANT: to avoid splashes, never remove
the fi lter holder while the appliance is deliver-
ing coff ee.
8. TO ELIMINATE THE USED COFFEE GROUNDS, block
the fi lter in place using the lever incor-
porated in the handle and empty
the coff ee by turning the fi l-
ter holder upside down and
tapping.
9. TO TURN THE COFFEE MACHINE OFF,
press the ON/OFF button.
IMPORTANT: the fi rst time the
appliance is used, all accessories
and the internal circuits must be
washed through by making at least
fi ve coff ees without using ground coff ee.
3. DISTRIBUTE THE GROUND COFFEE evenly and press
lightly with the
presser
NB: Correct
pressing of the
ground coff ee
is essen-
tial to
obtain a
good espresso. If pressing is ex-
cessive, coff ee delivery will be slow and the
froth will be dark. If pressing is too light, coff ee
delivery will be too rapid and the froth will be
skimpy and light coloured.
4. REMOVE ANY
EXCESS COFFEE
from the rim
of the fi l-
ter hold-
er and
attach the fi l-
ter holder to the appli-
ance. Rotate fi rmly to avoid leaks of
water.
7
1
2
HOW TO PREPARE ESPRESSO COFFEE USING PODS
1. PREHEAT THE APPLIANCE as described in the sec-
tion “PREHEATING THE COFFEE UNIT”, making
sure the fi lter holder is attached. This obtains a
hotter coff ee.
NB: Use pods conforming to the
ESE standard indicated on the
pack with the following logo:
THE ESE STANDARD is a system ac-
cepted by leading pod producers
and enables espresso coff ee to be prepared
simply and cleanly.
2. PLACE THE SMALL FILTER (1 cup or pods)
in the fi lter holder, making sure the
projection is correctly inserted in
the slot.
3. INSERT A POD, centring it as far as possible
on the fi lter. Always follow the instruc-
tions on the pod pack to position the
pod on the fi lter correctly.
4. ATTACH THE FILTER HOLDER to the appliance. Al-
ways rotate
as far as it will
go.
5. PROCEED AS in points 5, 6 and 7 in the previ-
ous paragraph.
8
HOW TO MAKE CAPPUCCINO COFFEE
1. PREPARE THE ESPRESSO COFFEES as described in
the previous paragraphs, using suffi ciently
large cups.
2. PRESS THE STEAM BUTTON and wait
for the OK light to come on. This in-
dicates that the boiler has reached
the ideal temperature for steam
production.
3. IN THE MEANTIME, fi ll a recipi-
ent with about 100 grams of
milk for each cappuccino to be
prepared. The milk must be at
refrigerator temperature (not
hot!). In choosing the size of the recipient, bear
in mind that the milk doubles or triples
in volume.
NB: YOU ARE RECOMMENDED TO USE
SEMISKIMMED MILK AT REFRIGERATOR
TEMPERATURE.
4. PLACE THE RECIPIENT containing the
milk under the cappuccino maker.
7. POUR THE FROTHED MILK into the cups contain-
ing the espresso coff ee prepared previously.
The cappuccino is ready. Sweeten to taste and,
if desired, sprinkle the froth with a little cocoa
powder.
NB: To prepare more than one cappuccino,
fi rst make all the coff ees then at the end pre-
pare the frothed milk for all the cappuccinos.
NB: to make coff ee again after the milk has
been frothed, cool down the boiler fi rst or the
coff ee will be burnt. To cool it, place a contain-
er under the boiler outlet, press the steam but-
ton and run off water until the OK light goes
out. Make the coff ee as described in the previ-
ous paragraphs.
5. DIP THE CAPPUCCINO MAKER into
the milk for about 5 mm and
turn the steam knob anti-
clockwise, taking care not to
immerse the raised line on the
cappuccino maker (indicated by
the arrow).
Turn the steam knob at least a half turn anti-
clockwise. Steam is discharged from the cap-
puccino maker, giving the milk a creamy frothy
appearance. To obtain a creamier froth, dip the
cappuccino maker into the milk and rotate the
container with slow movements from the bot-
tom upwards.
6. WHEN THE REQUIRED TEMPERATURE
IS REACHED (60°C is ideal), interrupt
steam delivery by rotating the
steam knob clockwise and at the
same time pressing
the steam button.
9
IMPORTANT: always clean the cappuccino
maker after use. Proceed as follows:
1. DISCHARGE A LITTLE STEAM for a few seconds by
rotat-
ing the
steam
knob.
This
emp-
ties any
milk left
inside the
steam spout.
IMPORTANT: To ensure hy-
giene, you are recommended to follow
this procedure each time you make cappucci-
no to avoid milk stagnating in the milk circuit.
3. REMOVE THE NOZZLE from the steam
tube by pulling it downwards.
4. WASH THE CAPPUCCINO MAKER and
steam nozzle thoroughly with
warm water.
5. MAKE SURE the two holes shown
in are not blocked. If necessary,
clean with a pin.
6. REPLACE THE STEAM NOZZLE by in-
serting it onto the steam tube
and rotating fi rmly towards the
top of the tube.
7. REPLACE THE CAPPUCCINO MAKER by
inserting it and rotating anticlockwise.
HOT WATER PRODUCTION
1. TURN THE APPLIANCE ON by pressing
the ON/OFF button. Wait until the
OK indicator light comes on.
2. PLACE A RECIPIENT under the cappuccino mak-
er.
3. PRESS THE COFFEE BUTTON and at the same time
turn the steam knob anticlockwise.
Water comes out of the cappucci-
no maker;
4. TO INTERRUPT DELIVERY OF HOT WATER, close the
steam knob by rotating clockwise
and press the coff ee button again.
(You should not run off hot water
for more than 45 seconds at a time).
2. WITH ONE HAND, HOLD THE CAP-
PUCCINO TUBE FIRMLY and with the
other unscrew the cappuccino
maker itself by rotating clock-
wise and extracting downwards.
10
CLEANING AND MAINTENANCE
1. BEFORE PERFORMING ANY CLEANING operations,
leave the appliance to cool down and unplug
from the mains socket.
2. DO NOT USE SOLVENTS OR ABRASIVE cleaning
products to clean the appliance. A soft, damp
cloth is suffi cient.
3. EMPTY AND WASH the drip tray and drip mesh
frequently.
4. CLEAN THE WATER TANK regularly.
IMPORTANT: Never immerse the appliance in
water. It is an electrical appliance.
CLEANING THE FILTER HOLDER
ABOUT EVERY 200 COFFEES, clean the fi lter holder
for ground coff ee as follows:
Remove the filter with frother.
Clean the inside of the filter holder. Never
wash in a dishwasher.
Unscrew the cap of the frother
by turning anticlockwise.
Remove the frother from
the container by pushing it
from the cap end.
Remove the gasket.
RINSE ALL COMPONENTS and clean
the metal fi lter thoroughly in
hot water using a brush.
MAKE SURE the holes in the metal fi lter are not
blocked. If necessary, clean with a
pin.
Replace the filter and gasket on
the plastic disk. Make sure to in-
sert the pin on the plastic disk into
the hole in the gasket indicated by
the arrow.
Replace the assembly in the steel
filter container, making sure the
pin is inserted in the hole in the
support.
Finally, screw on the cap by
turning clockwise. Failure to
clean as described above in-
validates the guarantee.
11
CLEANING THE BOILER OUTLET
ABOUT EVERY 300 COFFEES, the espresso boil-
er outlet must be
cleaned as follows:
1. MAKE SURE the ap-
pliance is not hot and
that it is unplugged
from the mains.
DESCALING
3. CLEAN THE BOILER with a damp cloth
4. CLEAN THE OUTLET thoroughly in
hot water using a brush. Make sure
the holes are not blocked. If neces-
sary, clean with a pin.
5. RINSE UNDER RUNNING WATER, rubbing all the
time.
6. SCREW THE BOILER OUTLET BACK ON. Failure to
clean as described above invalidates the guar-
antee.
YOU ARE RECOMMENDED TO DESCALE the coff ee ma-
chine about every 200 coff ees or a maximum
of every two months.
YOU SHOULD USE A COMMERCIALLY AVAILABLE PROD-
UCT SPECIFICALLY FOR DESCALING ESPRESSO COFFEE MA-
CHINES.
IF SUCH A PRODUCT IS NOT AVAILABLE, proceed as fol-
lows.
1. FILL THE TANK with half a litre of water.
2. DISSOLVE 2 spoonfuls (about 30 grams) of cit-
ric acid (obtainable from chemist’s or drug
stores)
3. PRESS THE ON/OFF BUTTON and wait for the OK
indicator light to come on.
4. MAKE SURE the fi lter holder is not attached
and position a recipient under the boiler out-
let.
5. PRESS THE COFFEE BUTTON, half empty the tank
by turning the steam knob every now and
then to run off a little solution. Stop run-off by
pressing the button again.
6. TURN THE APPLIANCE OFF.
7. LEAVE THE SOLUTION TO WORK for 15 minutes
then turn the appliance on again.
8. PRESS THE COFFEE BUTTON to empty the tank
completely.
9. TO ELIMINATE RESIDUES of solution and scale,
rinse the tank well, fi ll with clean water (with-
out citric acid) and replace in position.
10. PRESS THE COFFEE BUTTON and run the water
off until the tank is completely empty
11. INTERRUPT water run-off and repeat opera-
tions 9, 10 and 11 again. Repair of damage to
the coff ee machine caused by scale is not cov-
ered by the guarantee unless descaling is per-
formed regularly as described above.
2. USING A SCREWDRIVER, unscrew the screw fi xing
the espresso boiler outlet fi lter
12
NO ESPRESSO COFFEE IS DELIVERED No water in the tank
The holes in the fil-
ter holder spouts are
blocked.
The espresso boiler outlet
is blocked
The filter is blocked
The tank is incorrectly in-
serted
PROBLEM POSSIBLE CAUSE SOLUTION
Fill the tank with water
Clean the spout holes.
Clean as described in the
chapter “Cleaning the
boiler outlet”
Clean as described in the
section “cleaning the filter
holder”.
Insert tank correctly.
THE ESPRESSO COFFEE DRIPS from
the edges of the fi lter holder
rather than the holes.
The filter holder is insert-
ed incorrectly
The espresso boiler gas-
ket has lost elasticity
The holes in the filter
holder spouts
Attach the filter holder
correctly and rotate firmly
as far as it will go.
Have the espresso boiler
gasket elasticity replaced
at a service centre
Clean the spout holes.
THE ESPRESSO COFFEE IS COLD The espresso OK indicator
light was not on when the
coffe switch was pressed
No preheating performed
The cups were not pre-
heated
Wait until the OK light
comes on not on when
the coffee switch was
pressed.
Preheat as described in
the paragraph “Preheat-
ing the appliance”.
Preheat the cups by rins-
ing them in hot water.
THE PUMP IS EXCESSIVELY NOISY The water tank is empty
The tank is incorrectly in-
serted.
Fill tank
Insert tank correctly.
13
THE COFFEE FROTH IS TOO LIGHT
(delivered from the spout too
fast)
PROBLEM POSSIBLE CAUSE SOLUTION
The ground coffee is
not pressed down firmly
enough
There is not enough
ground coffee
The ground coffee is too
coarse
Incorrect type of ground
coffee.
Press the ground coffee
down more firmly).
Increase the quantity of
ground coffee
Use ground coffee for
espresso coffee ma-
chines only
Change the type of
ground coffee.
THE COFFEE FROTH IS TOO DARK
(delivered from the spout too
slowly)
The ground coffee is
pressed down too firmly
There is too much ground
coffee
The espresso boiler outlet
is blocked
The filter is blocked
The ground coffee is too
fine
The coffee is damp or
ground too fine
Incorrect type of ground
coffee.
Press the coffee down less
firmly.
Reduce the quantity of
ground coffee
Clean as described in the
chapter “Cleaning the
boiler outlet”
Clean as described in the
section “cleaning the fil-
ter holder”.
Use ground coffee for
espresso coffee machines
only
Use only ground coffee
for espresso coffee ma-
chines. Make sure it is not
damp
Change the type of
ground coffee.
NO MILK FROTH IS FORMED WHEN
MAKING CAPPUCCINO
Milk not cold enough.
Cappuccino maker dirty.
Always use semi-skimmed
milk at refrigerator tem-
perature.
Thoroughly clean the
holes in the cappucci-
no maker in
particular
those indi-
cated by the
arrows.
14
15
16
Whirlpool Sweden AB
GB
4619- 694- 61932
ENVIRONMENTAL HINTS
THE PACKING BOX may be fully recy-
cled as confi rmed by the recy-
cling symbol. Follow local
disposal regulations. Keep
potentially hazardous pack-
aging (plastic bags, polysty-
rene etc.) out of the reach of children.
THIS APPLIANCE is marked according to the Euro-
pean directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE). By ensuring
this product is disposed of correctly, you will
help prevent potential negative consequences
for the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product.
THE SYMBOL on the product, or on the docu-
ments accompanying the
product, indicates that this
appliance may not be treat-
ed as household waste. In-
stead it shall be handed over
to the applicable collection
point for the recycling of elec-
trical and electronic equip-
ment.
DISPOSAL must be carried
out in accordance with lo-
cal environmental regula-
tions for waste disposal.
For more detailed information about treat-
ment, recovery and recycling of this prod-
uct, please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
Before scrapping, cut off the mains cord so
that the appliance cannot be connected to the
mains.
TROUBLE SHOOTING GUIDE
WHEN CALLING FOR SERVICE, please give the se-
rial number and type number of the appli-
ance (see Service label). Consult your warranty
booklet for further advice.
IF THE MAINS CORD NEEDS REPLACING it should
be replaced by the original mains cord,
which is available via our service organi-
zation. The mains cord may only be re-
placed by a trained service technician.
SERVICE ONLY TO BE CARRIED OUT
BY A TRAINED SERVICE TECHNICIAN.
It is hazardous for anyone oth-
er than a trained person to car-
ry out any service or repair op-
eration, which involves the
removal of any cover.
DO NOT REMOVE ANY COVER.
SUPPLY VOLTAGE 220 - 230 V/50 HZ
RATED POWER INPUT 1100 W
FUSE 10 A (UK 13 A)
OUTER DIMENSIONS (HXWXD) 382 X 595 X 305