Whirlpool AKZ 669/IX User Manual
Displayed below is the user manual for AKZ 669/IX by Whirlpool which is a product in the Ovens category. This manual has pages.
Related Manuals
16
INSTRUCTION FOR USE
INSTALLATION ............................... 17
ADVICE FOR SAFEGUARDING THE
ENVIRONMENT............................................20
IMPORTANT NOTES....................................20
BEFORE USING THE OVEN.........................21
OVEN ACCESSORIES...................................22
CARE AND MAINTENANCE........................23
TROUBLESHOOTING GUIDE......................27
AFTER SALES SERVICE................................27
To make the most of your new oven, read the user's instructions carefully and keep them on hand
for consultation in the future.
31002019GB.fm Page 16 Wednesday, December 3, 2008 11:47 AM
17
INSTALLATION
Recommendations
IMPORTANT: Disconnect the oven from the mai ns before ca rrying out any insta llation work
or servicing.
•Installation must be carried out by a qualified technician in accordance with the manufacturer's
instructions and in compliance with local regulations.
•Unpack the oven and make sure that the oven has not been damaged during transport and that the
oven door closes properly. If you are not sure contact the dealer or the nearest service centre.
•After removing the oven from its packaging, leave it on the polystyrene base to prevent it from being
damaged.
•When installing the oven it is advisable to wear protective gloves.
•The oven is provided with two side handles (B) to facilitate installation (fig. 7).
Preparing the housing unit
•Kitchen units in contact with the oven must be heat resistant (90 °C min).
•Cut the kitchen unit and worktop to fit before installing the oven. Carefully remove any shavings or
sawdust that could prevent the oven from running properly.
•The dimensions of the housing units in which the oven can be installed are shown in figures 1, 2 and 3.
The dimensions of the oven are shown in figure 4.
•To allow for proper ventilation, an opening should be left at the bottom of the housing unit. Pay
attention to the dimensions. The bottom of the oven must not be accessible after installation.
•During installation make sure that the sides of the oven do not touch the adjacent units.
1
23
4
31002019GB.fm Page 17 Wednesday, December 3, 2008 11:47 AM
18
•For ovens installed under the worktop, leave a minimum clearance of 5 mm between the upper edge
of the oven and the lower edge of the worktop (fig. 5). For correct operation of the appliance, this
clearance must always be unobstructed.
•If the kitchen unit is not securely fixed to the wall, it must be anchored with standard brackets (A)
(fig. 6).
Electrical connection
Regulations require that the appliance be earthed.
•Connection to the mains must be carried out by a qualified electrician in accordance with the
manufacturer's instructions and in compliance with local regulations.
•The installer is responsible for connecting appliances correctly to the mains and for observing the safety
regulations.
•The oven power cable must be long enough to connect the built-in oven to the mains.
•Observance of safety directives requires that a multi-pole switch with a minimum contact gap of 3mm
be used for the installation.
•Do not use multiple plug adapters or extension leads.
•After the oven has been installed, the electrical components must be inaccessible.
56
31002019GB.fm Page 18 Wednesday, December 3, 2008 11:47 AM
19
Connecting the oven to the power supply
•Make sure that the voltage indicated on the rating plate is the same as the mains voltage.
The rating plate is on the front edge of the oven (visible when the door is open).
•If the power cable is not present proceed as follows:
1. Remove the two fastening screws of the terminal box cover located on the bottom part of the
oven's rear covering.
2. Remove the cover to gain access to the terminal box and insert the power cable (see table) through
the opening located on the bottom of the oven.
3. Connect the cable to the terminal box, tighten the screws as far as they will go and secure it to the
cable fastener.
4. Put the cover back on by inserting the two blades in the slots and fasten it with the two screws.
Securing the oven
•Lift up the oven getting hold of it by the handles (B) on the sides and insert it into the housing
unit, being careful not to trap the power supply cable (fig. 8).
•Center the oven in the housing unit before securing it.
•The oven comes with spacers already fitted to facilitate the anchoring of the oven to the
housing unit with the screws provided (as shown in fig. 9).
Power supply cable table
N° of leads Type of cable
1N+
~H05 RR-F 3 X 1,5 mm²
89
7
31002019GB.fm Page 19 Wednesday, December 3, 2008 11:47 AM
20
ADVICE FOR SAFEGUARDING THE
ENVIRONMENT
Disposal of packaging materials
•The packaging material is 100% recyclable and is
marked with the recycle symbol .
•The various parts of the packing must therefore be
disposed of responsibly and in full compliance with
local authority regulations governing waste disposal.
Disposal of used household appliances
This appliance is marked in conformity with European
Directive 2002/96/EC, Waste Electrical and
Electronic Equipment (WEEE).
By ensuring that this product is correctly disposed
of, the user helps prevent potential negative
consequences for the environment and health.
The symbol on the product or on the
accompanying documentation indicates that this
product must not be treated as domestic waste
but must be consigned to a suitable collection point
for the recycling of electrical and electronic
equipment.
When disposing of the product, comply with local
waste-disposal regulations.
•For further information on the treatment,
recovery and recycling of this product, contact
the respective local authority, the service for the
collection of household waste, or the shop where
the product was bought.
Energy saving
•Only pre-heat the oven if specified in the cooking
table of the Product Description Sheet or in your
recipe.
•Use dark, black enamelled baking moulds as they
absorb heat very well.
IMPORTANT NOTES
Attention:
•Not intended for use by young children and
infirm persons without supervision.
•This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge unless
they have been given initial supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
•Young children should be supervised to
ensure they not play with the appliance.
•The accessible parts of the oven may get
very hot during use. Keep children away.
•Never use abrasive materials or substances
to clean the GLASS, to prevent damaging it.
•The unit gets very hot during use. Do not
touch the heating elements in the oven.
•This oven is designed solely for use as a home
appliance for cooking food. No other type of use
is allowed. The Manufacturer declines all
responsibility for inappropriate use or incorrect
setting of the controls.
•Any repairs or adjustments must be carried out
exclusively by a qualified technician.
•Never expose the oven to atmospheric agents.
•Do not put heavy objects on the door because
they could damage the oven cavity and hinges.
Do not cling to the door.
•Never hang anything heavy on the oven door
handle.
•Do not cover the bottom of the oven with
aluminium foil or other objects.
•The oven door must close properly. The door
seals must be kept clean.
•Do not pour water directly into the inside of a
hot oven. The enamel coating could be damaged.
•Fruit juice drippings from the baking tray may
leave permanent stains. We recommend the
oven be cleaned before reusing it.
•Never drag pots and pans across the bottom of
the oven to prevent the coating from being
scratched.
•Residual condensation after cooking could damage
the oven and surrounding kitchen units in time.
We recommend that you:
- set the lowest temperature;
- cover food;
- remove food from the oven;
- dry the wet parts when the oven is cool.
•The front panel and the handle of the oven door
warm up when the appliance is switched on for a
long time at high temperatures.
31002019GB.fm Page 20 Wednesday, December 3, 2008 11:47 AM
21
•Never touch the oven with any wet part of the
body and do not operate it with bare feet.
•Do not pull the appliance or the power supply cable
to disconnect them from the electrical supply.
•Do not allow children to touch:
- the oven and its controls, especially when in
operation and immediately afterwards to
avoid injury;
- packaging (bags, polystyrene, metal parts,
etc.);
- an oven to be scrapped.
•Make sure that the electrical cables of other
appliances used near the oven do not touch hot
parts and are not trapped in the oven door.
•Some oven models are equipped with an air
cooling system to prevent the front of the oven
and cabinet cavity from reaching excessively high
temperatures.
Attention: Steam and smoke are vented through
an opening located between the control panel and
the oven door. Do not obstruct the vent opening.
•Do not place inflammable material in the oven or
nearby: a fire may break out if the oven is
inadvertently switched on.
•Use oven gloves to remove pans and accessories,
when the oven is hot.
•If alcoholic beverages are added when roasting or
cooking cakes and sweets (for example. rum,
cognac, wine, etc.) remember that alcohol
evaporates at high temperatures. It may happen
that vapours released by the alcohol can catch
fire when they are in contact with the electric
heating element.
•Do not heat or cook sealed jars or containers in
the oven. The pressure that develops inside the
packaging might cause it to explode, damaging
the oven.
•Do not use containers made of synthetic material
for cooking (except for packages specifically
designed for this purpose; see the manufacturer's
instructions). They could melt at high
temperatures.
•Always keep a watch on pans when cooking with
oil and grease. Oil and fat can overheat and catch
fire!
•Never pull out fully loaded shelves. Use extreme
caution.
BEFORE USING THE OVEN
•Remove the accessories from the oven and heat
it 200°C for about an hour to eliminate the smell
of the protective grease and insulating materials.
Keep the window open during this operation.
•Before use, remove:
- stickers on the front and oven door, except
for the rating plate;
- cardboard protection and protective plastic
film from the front panel controls and other
parts of the oven;
- any sticky labels from the accessories (for
example, under the drip tray).
31002019GB.fm Page 21 Wednesday, December 3, 2008 11:47 AM
22
OVEN ACCESSORIES
Accessories supplied depend on the model. The
accessories provided with the oven are listed in the
Product Description Sheet provided separately (under
Accessories).
Drip tray (1)
The drip tray is designed to collect fat and food particles when it
is positioned under the grid or as a plate, such as when cooking
meat, chicken and fish with or without vegetables. Pour a little
water into the drip tray to prevent spatters of fat and smoke.
Baking tray (2)
For cooking biscuits, cakes and pizzas.
Grid (3)
The grid can be used to grill food or as a support for baking trays,
cake tins and other cooking receptacles. It can be placed on any
of the runners in the oven. The grid can be inserted with its
curved side facing upwards or downwards.
Turnspit (4)
Use the turnspit as indicated in the relevant chapter in the
Product Description Sheet supplied separately.
Grill pan set (5)
The pan set comprises a grid (5a), an enamel drip tray (5b).
If your pan set is not equipped with a handle (5c) it can be
purchased via Service.
This set must be placed on the grid (3) and used with the Grill
function.
Wflex baking tray (6)
The Wflex baking tray is ideal for cooking savoury or sweet
dishes and can be used in place of metal baking trays.
It is perfect for freezing and cooking (freezer, electric oven, gas
oven and microwave).
It can also be used with the grill function, placing it on the
bottom grid.
3
4
5
2
5a
5b
5c
6
1
31002019GB.fm Page 22 Wednesday, December 3, 2008 11:47 AM
23
CARE AND MAINTENANCE
Important: never clean the appliance with high
pressure water or steam cleaning equipment.
Exterior of the oven
•Clean with a damp cloth. If it is very dirty, add a
few drops of washing up detergent to the water.
Wipe with a dry cloth.
•Do not use corrosive or abrasive detergents,
which dull the surface.
In the event of one of these products coming into
contact with the oven, clean it immediately using
a damp cloth.
•Slight differences in colour on the front of the
appliance are determined by the different
materials used, such as glass, plastic and metal.
Ovens with aluminium front panel
•Clean using a delicate detergent and a soft
window cleaning cloth or a microfibre cloth that
does not leave fibres on the surface. Wipe
horizontally, without exerting pressure.
•Do not use corrosive products, hard sponges or
rough cloths. Clean the aluminium surfaces with
a dry cloth.
Accessories
•Soak the accessories in water with washing up
detergent immediately after use. Food residues
can be easily removed using a brush or sponge.
Self-cleaning function (pyrolysis)
Your oven is self-cleaning. It does this by burning off
the fat spatters produced inside the oven during
cooking at a temperature of approx.
500°C. At this high temperature, the deposits turn
into a light ash which can be easily wiped away with
a damp cloth, when the oven is cool.
•It is not necessary to select the pyrolytic function
after every use, only when the oven is very dirty.
•If the oven is fitted under a hob, make sure that
during the self-clean cycle (pyrolysis) all burners
or electric hotplates are turned off.
•Remove all accessories before running the
pyrolytic function.
•For optimum cleaning of the oven door, remove
the worst soiling with a damp sponge before
using the pyrolytic function.
•To make this function more efficient, the oven
has 2 pyrolytic cleaning cycles:
- an energy saving one (PYRO EXPRESS) which
consumes 25% less energy than the standard
cycle. Used after the second or third time you
cook meat, this feature will ensure the oven
remains clean.
- a standard one (PYRO), suitable for cleaning a
very dirty oven.
6th Sense models automatically detect how dirty
the inside of the oven is and set the ideal cleaning
time.
•As a safety measure, the oven door locks
automatically after selecting the pyrolytic cycle.
Due to the very high temperature inside the
appliance during the self-cleaning cycle, the oven
door will not open even by turning the selector
to 0.
When to clean by pyrolysis
If your oven smokes during pre-heating or if there
is a lot of smoke during a cooking cycle, run the
pyrolytic cycle. You can also use this function if
there is an unpleasant smell after cooking various
foods (lamb, fish, grilled food…)
FOOD WITH LITTLE
SPATTERING
Biscuits,
legumes, sweets,
quiches, soufflés.
Foodstuffs that
do not spatter.
FOOD THAT SPATTERS Meat, fish (in a
heat-resistant
dish), stuffed
vegetables.
FOOD THAT SPATTERS
BADLY Large pieces of
meat on the spit.
31002019GB.fm Page 23 Wednesday, December 3, 2008 11:47 AM
24
INSTRUCTIONS FOR REMOVING THE DOOR
Attention: When carrying out the following operations it
is advisable to wear protective gloves
These instructions should be carefully followed both to
prevent injury and in order not to damage the oven and
the hinges.
Take special care when removing the glass, because its
position has been precisely chosen.
Do not touch the hinges when cleaning and/or removing
the door (fig. 9)
How to remove the oven door:
1. Put on protective gloves
2. Open the oven door fully (see fig. 1)
3. Lift the two catches as far as they go (see fig. 2)
4. Remove the door by closing it partially and pulling it
upwards (see fig. 3)
To disassemble the oven door:
1. Place the oven door on a horizontal surface (fig. 4)
2. Unscrew and remove the 2 glass support screws A at the
side of the hinges. (fig. 4, fig. 5)
1
2
3
4
5
31002019GB.fm Page 24 Wednesday, December 3, 2008 11:47 AM
25
3. Lift the bottom of the inside sheet of glass and remove it
(fig. 6)
4. Slip out the second and the third sheet of glass, paying
particular attention to the position of the word
SAFEGLASS (Fig. 7)
5. Refit the sheets of glass in reverse order making sure that:
- The word SAFEGLASS on the intermediate sheets is
facing upwards so as to be correctly legible (fig. 8);
- if one of the intermediate sheets does not have the word
SAFEGLASS it must be inserted in the position closest to
the internal glass.
Put the inside glass into position with the word SAFEGLASS
facing the top of the door. (fig. 6)
Reposition and screw on the two glass supports A (fig. 4 and
fig. 5)
Note: a slight play between the inside glass and the door
uprights is to be considered normal as it compensates
expansion of the glass caused by heat.
To remount the door:
6. Insert the hinges into their grooves and lower the door
fully (fig. 3)
7. Lower the two catches again (fig. 2)
8. Close the oven door fully.
6
7
9
8
31002019GB.fm Page 25 Wednesday, December 3, 2008 11:47 AM
26
Pay attention to the hinges when cleaning and/or removing the
door (fig. 9).
Changing the rear oven lamp bulb:
1. Disconnect the oven from the electrical supply.
2. Let the oven cool before turning the lamp cover left to
unscrew it (see fig. 10).
3. Change the bulb (see note).
4. Screw the lamp cover back on.
5. Reconnect the oven to the electrical supply.
Note: use only 25 W/230 V, E-14 type,
T500°C bulbs available from After Sales Service.
IMPORTANT: Do not use the oven until the lamp cover
has been repositioned.
10
31002019GB.fm Page 26 Wednesday, December 3, 2008 11:47 AM
27
TROUBLESHOOTING GUIDE
Oven not working:
•Check for the presence of mains electrical power
and if the oven is connected to the electrical
supply.
•Turn off the oven and restart it to see if the fault
persists.
If the door will not open:
•Turn off the oven and restart it to see if the fault
persists.
IMPORTANT:
•Check that the oven control knob is not turned
to “0” or to “lamp” .
- If the electronic programmer (depending on
model) display presents the message
"“, consult the product description
sheet provided separately and/or the
electronic programmer description.
- If the electronic programmer (depending on
the model) presents the message “F XX”,
contact the nearest After Sales Service.
Specify in this case the number that follows
the letter “F”.
AFTER SALES SERVICE
Before you call the After Sales Service:
1. Try to solve the problem yourself following
the points described in “Troubleshooting
Guide“.
2. Turn the appliance off and on again, to make
sure that the problem has been solved.
If after the above checks the fault still occurs,
get in touch with the nearest After Sales
Service.
Please give:
•a brief description of the fault;
•the type and exact model of the oven;
•the service number (number after the word
Service on the rating plate), located on the
right hand edge of the oven cavity (visible
when the oven door is open). The service
number is also indicated on the guarantee
booklet;
•your full address;
•your telephone number.
If any repairs are required, please contact an
authorised After Sales Service (to guarantee
that original spare parts will be used and repairs
carried out correctly).
Failure to comply with these instructions may
compromise the safety and quality of the
product.
DECLARATION OF CONFORMITY
•This oven is suitable for contact with
foodstuffs and complies with EEC (CE)
Regulation n. 1935/2004.
•This appliance is designed to be used for
cooking only.
Any other use (for example. for room
heating) is considered as improper use and
potentially dangerous.
•This appliance has been designed,
constructed and marketed in compliance
with:
- safety objectives of the “Low Voltage”
Directive 2006/95/CE (which replaces
73/23/CEE and subsequent
amendments);
- the protection requirements of EMC
Directive 89/336/EEC;
- the requirements of Directive 93/68/EEC.
31002019GB.fm Page 27 Wednesday, December 3, 2008 11:47 AM