Whirlpool GMA 9522/IXL User Manual
Displayed below is the user manual for GMA 9522/IXL by Whirlpool which is a product in the Hobs category. This manual has pages.
Related Manuals
AE IT PT
EN
400011091362
IMPORTANT SAFETY INSTRUCTIONS
These instructions shall also be available on website: www.whirlpool.eu
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT
This manual and the appliance itself provide important safety messages, to be read and observed at all times.
This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.
All safety messages will follow the safety alert symbol and either the terms:
DANGER
Indicates a hazardous situation which, if not avoided, will cause serious injury.
WARNING
Indicates a hazardous situation which, if not avoided, could cause serious injury.
All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are
not followed.
• The appliance must be disconnected from the power supply before carrying out any installation work.
• Installation and maintenance must be carried out by a qualied technician, in compliance with the manufacturer’s instructions and local safety regulations.
Do not repair or replace any part of the appliance unless specically stated in the user manual.
WARNING
If the information in this manual is not followed exactly, a re or explosion may result causing property damage or injury.
• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this appliance.
What to do if you smell gas:
-Do not try to light any appliance.
-Do not touch any electrical switch.
-Do not use any phone in your building.
-Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
-If you cannot reach your gas supplier, call the fire department.
-Installation and service must be performed by a qualified installer, service agency or the gas supplier.
-Use appliance in well ventilated rooms only.
The electrical and gas connections must comply with local regulations.
• When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that provides full disconnection.
• Regulations require that the appliance is grounded.
• The power cable must be long enough for connecting the appliance, once tted in its housing, to the power supply.
• Use only exible or rigid metal hose for gas connection.
• If necessary, the electrical power cable must be replaced exclusively with a power cable having identical characteristics to the original supplied by manufacturer
(type H05V2V2-F 90°C or H05RR-F). This operation must be performed by a qualied electrician.
• The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising from failure to comply with these requirements.
• Do not use multiple plug adapters or extension cords.
• Do not pull the power supply cord in order to unplug the appliance.
• The electrical components must not be accessible to the user after installation.
• Do not touch the appliance with any wet part of the body and do not operate it when barefoot.
• This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as a space heater to heat or warm the room.
Doing so may result in carbon monoxide poisoning and overheating of the hob. The Manufacturer declines all responsibility for inappropriate use or incorrect
setting of the controls.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or with lack of experience and
knowledge of the appliance, unless supervised or previously instructed in its use by those responsible for their safety.
• Young children should be kept away from the appliance and supervised to ensure that they do not play with it.
• The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or install an extractor hood with exhaust duct.
• In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood extraction speed).
• After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.
• Overheated oils and fats catch re easily. Always remain vigilant when cooking foods rich in fat, oil or alcohol (e.g. rum, cognac, wine).
• Keep the packaging materials out of the reach of children.
• Before cleaning or maintenance wait for hob to cool down.
• These instructions are valid only for those countries whose symbol is shown on the rating plate (under cooktop).
• This product is not intended to be installed and operated outdoor.
SAVE THESE INSTRUCTIONS
BUILT-IN GAS HOB
INSTALLATION
After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service.
TECHNICAL INFORMATION FOR THE INSTALLER
• Use protective gloves for handling, preparing and installing the product.
• This product can be embedded in a worktop 20 ÷ 60 mm thick.
• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must
be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom
of the hob. In the case that you intend to install an oven beneath the hob, make sure that it is equipped with a cooling system. The manufacturer
declines all liability if another brand oven is installed beneath the hob.
Before installation, make sure that:
• the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table);
• the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;
• this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation regulations. Particular attention shall
be given to the relevant requirements regarding ventilation;
• combustion products are discharged outdoors through specic hoods or wall and/or window mounted electrical fans.
GAS CONNECTION
WARNING
This operation must be performed by a qualied technician.
• The gas supply system must comply with local regulations.
• You can nd specic local regulations for some countries in the paragraph “Reference to Local Regulations”.
If no information concerning your Country is given, please ask details to your Installer.
• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper
or steel pipe with ttings complying with local regulations, or by means of a continuous-surface stainless steel
hose complying with local regulations. The maximum length of the hose is 2 linear metres.
• Connect elbow (A)* or (B)* supplied with to the hob inlet main pipe and interpose the washer (C) supplied,
in compliance with EN 549.
* Use elbow (A) for France and elbow (B) for all other destinations.
IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of
the furniture. It must pass through an area where there are no obstructions and where it is possible to
inspect it on all its length.
• After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs
from max position to minimum position to check ame stability.
ELECTRICAL CONNECTION
WARNING
This operation must be performed by a qualied technician.
L
Earth
(yellow/green)
N
WARNING
• The electrical connections must comply with local regulations.
• The earthing of this appliance is compulsory by law.
• Do not use an extension cord.
IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.
ASSEMBLY
Use protective gloves for cleaning the product perimeter surface, then apply the supplied gasket to the
hob as shown in the gure.
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws
in accordance with the thickness of the worktop (see the following gures).
C
B
C
C
A
20
30
60
40
Top 20 mm Top 40 mm
Top 30 mm Top 60 mm
NO
ADJUSTMENT TO DIFFERENT TYPES OF GAS
WARNING
This operation must be performed by a qualied technician.
If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the
injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in the Instruction:
• the gas injector must be changed by After Sales Service or a qualied technician;
• injector not supplied with the appliance must be ordered from After Sales Service;
• adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.
IMPORTANT: should you experience difculty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner
tap if found to be faulty.
IMPORTANT: when gas cylinder is adopted, the gas cylinder or gas container must be properly settled (vertical orientation).
REPLACING THE INJECTORS (see the injector table in the Instruction)
• Remove grids (A).
• Extract burners (B).
• Using a socket spanner of the appropriate size unscrew the injector (C), unscrew the injector
to be replaced.
• Replace it with the injector suitable for the new type of gas.
• Re-assemble the injector in (D).
• If you have a multiple crown burner use side spanner to replace the injector (E).
Before installing the hob, remember to afx the gas calibration plate supplied with the injectors in
such a way that it covers the existing information relating to gas calibration.
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:
• tighten screw to reduce the ame height (-);
• loosen screw to increase the ame height (+).
The adjustment must be performed with the tap in minimum gas setting position (small ame) :
• the primary air of the burners does not need to be adjusted;
• at this stage, light up the burners and turn the knobs from max position to minimum position
to check ame stability.
Upon completion of adjustment, reseal using sealing wax or an equivalent material.
REFERENCE TO LOCAL REGULATIONS
IT
Connection to gas supply
Before connecting the appliance, make sure that the gas supply system complies with standards UNI-CIG 7129 and UNI CIG 7131.
Gas connection
The connection to the mains gas network or gas cylinder must be made using a rigid copper or steel pipe with ttings complying with standards UNI-CIG 7129,
or using a continuous-surface stainless steel hose complying with standards UNI-CIG 9891. The maximum length of the hose is 2 m. Pressure control valves
must comply with standards UNI-CIG 7432.
AE PT
Ensure that the installation and gas connections are performed by a qualied technician, following the manufacturer’s instructions and in compliance with
current local safety regulations.
AFTER-SALES SERVICE
Before calling the After-Sales Service, make sure you can give the following information:
• type of fault or problem;
• exact model (written on the label afxed to the instruction/warranty);
• service number that follows the word SERVICE on the rating plate under the hob and on the label afxed to instruction/
warranty;
• your complete address and phone number.
If any repairs are required, please contact an authorised After-Sales Service, as indicated in the warranty.
TROUBLESHOOTING GUIDE
If the hob will not operate correctly, before calling the After-Sales Service, refer to the Troubleshooting Guide to determine the problem.
1. The burner fails to ignite or the ame is not even
Check that:
• the gas or electrical supplies are not shut off and especially that the gas supply tap is open;
• the gas cylinder (liquid gas) is not empty;
• the burner openings are not clogged;
• the plug end is not dirty;
• all the burner parts have been positioned correctly;
• there are no draughts near the hob.
2. The burner does not stay lit
Check that:
• when lighting the burner, the knob has been pressed for enough time to activate the protection device;
• the burner openings are not clogged near the thermocouple;
• the end of the safety device is not dirty;
• the minimum gas setting is correct (see relevant paragraph).
3. The containers are not stable
Check that:
• the bottom of the container is perfectly at;
• the container is centered on the burner;
• the grids have not been exchanged or positioned incorrectly.
If after the above checks the fault still occurs, get in touch with the nearest After Sales Service.
CLEANING THE HOB SURFACE
WARNING
Disconnect power before servicing.
• All the enamelled and glass parts should be cleaned with warm water and neutral solution.
• Stainless steel surfaces may be stained by calcareous water or aggressive detergents if left in contact for too long. Any food spills (water, sauce, coffee,
etc.) should be wiped away before they dry.
• Clean with warm water and neutral detergent, and then dry with a soft cloth or chamois. Remove baked-on dirt with specic cleaners for stainless steel surfaces.
NOTE: clean stainless steel only with soft cloth or sponge.
• Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers.
• Do not use steam cleaning appliances.
• Do not use ammable products.
• Do not leave acid or alkaline substances, such as vinegar, mustard, salt, sugar or lemon juice on the hob.
If you have a IXELIUM hob, observe the following cleaning recommendations:
• Use a soft cloth (microbre is best) dampened with water or with everyday glass cleaning detergent.
• Do not use paper kitchen towel, which can leave traces of streaks on the hob.
CLEANING THE HOB PARTS
• Grids, burner caps and burners can be removed to be cleaned.
• Clean them by hand with warm water and non-abrasive detergent, removing any food residues and checking that none of the burner openings is clogged.
• Rinse and dry.
• Ret burners and burner caps correctly in the respective housings.
• When replacing the grids, make sure that the panstand area is aligned with the burner.
• Models equipped with electrical ignition plugs and safety device require thorough cleaning of the plug end in order to ensure correct operation. Check these
items frequently, and if necessary, clean them with a damp cloth. Any baked-on food should be removed with a toothpick or needle.
NOTE: to avoid damaging the electric ignition device, do not use it when the burners are not in their housing.
DECLARATION OF CONFORMITY
This hob has been designed, constructed and marketed in compliance with:
• safety requirements of “Gas” Directive 2009/142/EC (ex: EEC 90/396);
• safety objectives of the “Low Voltage” Directive 2006/95/CE (which replaces 73/23/CEE and subsequent amendments);
• protection requirements of EEC Directive “EMC” 2004/108/EC.
This appliance meets the eco design requirements of European regulation N. 66/2014, in conformity to the European standard EN 30-2-1.
SAFEGUARDING THE ENVIRONMENT
Disposal of packing material
The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of the packing must therefore be disposed of responsibly
and in full compliance with local authority regulations governing waste disposal.
Scrapping the product
• This appliance is marked in conformity with European Directive 2012/19/UE, Waste Electrical and Electronic Equipment (WEEE).
• By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
• The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an
appropriate collection centre for the recycling of electrical and electronic equipment.
PRODUCT DESCRIPTION
32
78109
6
11
1 4 5
1. Removable panstand grids
2. Semi-rapid burner
3. Auxiliary burner
4. Semi-rapid burner
5. Rapid burner
6. 2 ring burner
7. Auxiliary burner control knob
8. Rapid burner control knob
9. 2 ring burner control knob
10. Semi-rapid burner control knob
11. Semi-rapid burner control knob
Symbols
Shaded circle Tap closed
Large ame Maximum ame
Small ame Minimum ame
PRATICAL ADVICE FOR USING THE BURNERS
This hob has burners of different diameters. For better burner performance, please stick to the following rules:
• use pots and pans with bottoms the same width as that of the burners or slightly larger (see table on the right);
• only use at-bottomed pots and pans;
• use the correct amount of water for cooking foods and keep the pot covered;
• make sure pots on the grates do not protrude beyond the edge of the hob;
• In the case of pans with convex bottoms (WOK), use the support grille (not included), which should be positioned
only on the 2 ring burner.
IMPORTANT: improper use of the grids can result in damage to the hob: do not position the grids upside down
or slide them across the hob.
Burner Pot Ø
2 Ring From 24 to 30 cm
Rapid From 24 to 26 cm
Semi-rapid From 16 to 22 cm
AuxiliaryFrom 8 to 14 cm
Do not use:
• cast iron griddles, ollar stones, terracotta pots and pans;
• heat diffusers such as metal mesh, or any other types;
• two burners simultaneously for one receptacle (e.g. sh kettle).
HOW TO USE THE HOB
WARNING
Do not let the burner ame extend beyond the edge of the pan.
IMPORTANT: when the hob is in use, the entire hob area may become hot.
• To ignite one of the burners, turn the relative knob anti-clockwise to the maximum ame setting.
• Press the knob against the control panel to ignite the burner.
• After the burner has ignited, keep the knob pressed for about 5-10 seconds to allow proper device operation.
This burner safety device shuts off the gas supply to the burner if the ame goes out accidentally (because of sudden draught, an interruption in the gas
delivery, boiling over of liquids, etc.).
• The knob must not be pressed for more than 15 sec. If, after that time has elapsed, the burner does not remain lit, wait at least one minute before
trying to light it again.
NOTE: should particular local conditions of the delivered gas make the ignition of burner difcult, it is advisable to repeat the operation with
the knob turned to small ame setting.
The burner might go out when the knob is released. This means that the safety device has not warmed up enough. In this case, repeat the operations
described above.
DIMENSIONS AND DISTANCES TO BE MANTAINED (mm)
860
840
860 min.
400 min. 400 min.
750 min.
50 min.
100
NOTE: In case of installation of a hood above the cooktop, please refer
to the hood instructions for the correct distance.
INJECTORS TABLE
+3H2II YROGETAC
Type of gas used Type of burner Injector
marking
Rated thermal
ow rate
Rated
consumption
Reduced heat
capacity
Gas pressure
mbar
.xam.tar.nimWkWk
NATURAL GAS
(Methane) G20
2 ring 149 H3 4.00 381 l/h2.20
17 20 25
rapid128B3.00286 l/h0.60
Semi-rapid 95 1.65 157 l/h0.35
Auxiliary78A 1.00 95 l/h0.30
LIQUEFIED
PETROLEUM GAS
(Butane) G30
2 ring100 4.00 291 g/h 1.90
20 28-3035
rapid873.00218 g/h0.60
Semi-rapid 67 1.65 120 g/h0.35
Auxiliary501.00 73 g/h 0.30
LIQUEFIED
PETROLEUM GAS
(Propane) G31
2 ring100 4.00 286 g/h 1.90
25 37 45
rapid873.00214 g/h0.60
Semi-rapid 67 1.65 118 g/h0.35
Auxiliary501.00 71 g/h 0.30
Type of gas used Model
conguration
Rated thermal
owrate (kW)
Total rated
consumption
Air required (m3) for
burning 1m
3 of gas
G20 20 mbar5 burners11.30 1076 l/
h9
.52
G30 28-30 mbar 5 burners11.30 822 g/
h3
0.94
G31 37 mbar5 burners11.30 807 g/
h2
3.80
ELEC
TRIC SUPPLY: 220-240 V ~ 50/60 Hz 0,6W
WOK ADAPTER and PRODUCT LID
(not included,this accessory can be purchased separately from the After-sales Service).