Whirlpool WFO 3T121 X User Manual
Displayed below is the user manual for WFO 3T121 X by Whirlpool which is a product in the Dishwashers category. This manual has pages.
Related Manuals
1
EN
DAILY REFERENCE
GUIDE
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please
register your appliance on:
www.whirlpool.eu/register
You can download the Safety Instructions and the Use
and Care Guide, by visiting our website
http://docs.whirlpool.eu and following the Instructions
on the back of this booklet.
Before using the appliance carefully read Health and Safety guide.
PRODUCT DESCRIPTION
APPLIANCE
1.Upper rack
2. Foldable flaps
3.Upper rack height adjuster
4.Upper spray arm
5.Lower rack
6.Cutlery basket
7.Lower spray arm
8.Filter Assembly
9.Salt reservoir
10.Detergent and Rinse Aid dispensers
11.Rating plate
12.Control panel
0000 000 00000
Service:
1
2
3
4
5
6
10
12
7
11
9
8
CONTROL PANEL
1. On-Off/Reset button with indicator light
2. Program selection button with indicator light
3. Multizone button with indicator light
4. Turbo button with indicator light / Key lock
5. Eco program indicator light
6. Key lock indicator light
7. Display
8. Program number and remaining time indicator
9. Tablet (Tab) indicator light
10. Closed water tap indicator light
11. Salt refill indicator light
12. Rinse Aid refill indicator light
13. Power Clean button with indicator light / Tablet (Tab)
14. Sani Rinse button with indicator light / Tablet (Tab)
15. Delay button with indicator light
16. Start/Pause button with indicator light / Drain out
4
1
3
2
916
14 15
65 7 8 11 12 1310
2
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining
elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see
PROGRAMS DESCRIPTION) and should be filled when the SALT REFILL
indicator light in the control panel is lit.
1.Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2.Position the funnel
(see figure)
and fill the salt
reservoir right up to its edge (approximately 1 kg);
it is not unusual for a little water to leak out.
3.Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, we recommend carrying out the
procedure before the washing cycle is started.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is for average (3) water hardness.
1. Switch on the appliance by pressing the
ON/OFF
button.
2. Switch off the appliance by pressing the
ON/OFF
button.
3. Hold down button
START/PAUSE
for 5 seconds, until you hear a
beep.
4. Switch on the appliance by pressing the
ON/OFF
button.
5. The current selection level number and the salt indicator light both
flash.
6. Press button
P
to select the desired hardness level
(see Water
Hardness Table).
7. Switch off the appliance by pressing the
ON/OFF
button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL
indicator light switches off.
If the salt container is not filled, the water softener and the heating
element may be damaged as a result.
FILLING THE RINSE AID DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser
A
should be filled
when the
RINSE AID REFILL indicator light
in the control panel is lit.
1. Open the dispenser
B
by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml) reference
notch of the filling space - avoid spilling it. If this happens, clean the spill
immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the
quantity of rinse aid used.
• Switch the dishwasher on using the
ON/OFF
button.
• Switch it off using the
ON/OFF
button.
• Press button
START/PAUSE
three times - a beep will be heard.
• Switch it on using the
ON/OFF
button.
• The current selection level number and rinse aid indicator light flash.
• Press button
P
to select the level of rinse aid quantity to be supplied.
• Switch it off using the
ON/OFF
button
Setting is complete!
If the rinse aid level is set to 1(ECO), no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 4 levels can be set according to the dishwasher model. The fac-
tory setting is for a medium level.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a high
number (4-5).
FILLING THE DETERGENT DISPENSER
To open the detergent dispenser use the
opening device A
.
Introduce the detergent into the dry dispenser B
only.
Place the amount of detergent for pre-washing
directly inside the tub.
1.When measuring out the detergent refer to the
(see PROGRAMS TABLE)
to add the proper quantity. Compartment
B
comprises a level showing the maximum quantity of liquid or powder
detergent that can be added to each cycle.
2. Remove detergent residues from the edges of the dispenser and close
the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the closing
device is secured in place.
The detergent dispenser automatically opens up at the right time according to
the program.
If all-in-one detergents are used, we recommend using the
TABLET
button,
because it adjusts the program so that the best washing and drying results are
always achieved.
Water Hardness Table
Level °dH
German degrees
°fH
French degrees
1 Soft 0 - 6 0 - 10
2 Medium 7 - 11 11 - 20
3 Average 12 - 17 21 - 30
4 Hard 17 - 34 31 - 60
5 Very hard 35 - 50 61 - 90
M
A
X
A
B
35
25
A
B
3
EN
PROGRAMS TABLE
ECO program data is measured under laboratory conditions according to European Standard EN 50242.
*) Not all options can be used simultaneously.
**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary
depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,
load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
Instructions on wash cycle selection.
ECO
Normally soiled crockery. Standard program, the most efficient in terms
of its combined energy and water consumption.
6th SENSE ®
For normally soiled dishes with dried food residues. Senses the level of
soiling on the dishes and adjusts the program accordingly. When the
sensor is detecting the soil level an animation appears in the display
and the cycle duration is updated.
INTENSIVE
Program recommended for heavily soiled crockery, especially suitable
for pans and saucepans (not to be used for delicate items).
DAILY
Normally soiled crockery. Everyday cycle, that ensures optimal cleaning
performance in shorter time.
SILENT
Suitable for night-time operation of the appliance. Optimum
performance ensured.
RAPID 30’
Program to be used for lightly-soiled dishes with no dried food
residues. Ideal for 2 place settings.
CRISTAL
Cycle for delicate items, which are more sensitive to high temperatures,
for example glasses and cups.
PRE-WASH
Crockery to be washed later. No detergent to be used with this
program.
SANITIZING
Normally or heavily soiled crockery, with additional antibacterial wash.
SELF-CLEAN
Cycle to be used to perform maintenance of the dishwasher. It cleans
the interior of the appliance using hot water.
Notes:
Optimum performance levels when using the “1 Hour” and “Rapid”
programs can be achieved by observing the maximum amounts of
specified place settings.
To reduce consumption even further, only run the dishwasher
when it is full.
Program
Drying
phase
Available options *)
Detergent
container
Duration of
wash program
(h:min)**)
Water con-
sumption
(litres/cycle)
Energy con-
sumption
(kWh/cycle)
Tub B
1. Eco 50° 3:10 9.0 0.83
2. 6th Sense 50°-60° 1:25-3:00 7.0-14.0 0.9-1.40
3. Intensive 65° - 2:50 14.0 1.50
4. Daily 50° - 1:30 12.0 1.15
5. Silent 50° - 3:30 15.0 1.15
6. Rapid 30’ 50° - - 0:30 9.0 0.50
7. Cristal 45° - 1:40 11.0 1.10
8. PreWash - - - - 0:12 4.5 0.01
9. Sanitizing 65° - 1:40 10.0 1.30
10. Self- Clean 65° - 0:50 8.0 0.80
4
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding
button (see CONTROL PANEL).
MULTIZONE
If there are not many dishes to be washed, a half loading
may be used in order to save water, electricity and
detergent.
Select the program and then press the MULTIZONE
button: the indicator over the button lights up and the
symbol of the chosen rack will appear on the display. By
default the appliance washes dishes in all racks.
To wash only the specific rack, press this button
repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (option is OFF and the appliance
will wash dishes in all racks).
Remember to load the upper or lower rack only, and
to reduce the amount of detergent accordingly.
TURBO
This option can be used to reduce the duration of the
main programs while maintaining the same washing and
drying performance levels.
After selecting the program, press the TURBO button and
the indicator light will switch on. To deselect the option,
press the same button again.
KEYLOCK
A long press (for 3 seconds) of TURBO button, will
activate the KEYLOCK function. The KEYLOCK function
will block the control panel except the ON/OFF button.
To deactivate the KEYLOCK, long press again.
WATER TAP CLOSED – Alarm
Flashes when there is no inlet water or water tap is closed.
EXTRA DRY
To improve the drying of the dishes, after selecting the
program, press the EXTRA DRY button and the indicator
light comes on.
A higher temperature during the final rinse and an
extended drying phase allow for improving drying. To
deselect the option, press the same button again. The
EXTRA DRY option results in the lengthening of the wash
cycle.
TABLET (Tab)
This setting allows you to optimize the performance of
the program according to the type of detergent used.
Press the TABLET button (the indicator and
corresponding symbol will light up) if you use combined
detergents in tablet form (rinse aid, salt and detergent in
1 dose).
If you use powder or liquid detergent, this option
should be off.
DELAY
The start of the program may be delayed for a period of
time between 0:30 and 24 hours.
1.Select the program and any desired options. Press the
DELAY button (repeatedly) to delay the start of the
program. Adjustable from 0:30 to 24 hours. With each
press of the button, the delay start increases by: 0:30 if
selection below 4 hours, 1:00 if selection is below 12
hours, 4 hours if selection is above 12 hours. If 24 hours
reached, and the button is pressed, the delayed start is
deactivated.
2. Press the START/PAUSE button: the timer will begin
counting down;
3. Once this time has elapsed, the indicator light switches
off and the program begins automatically.
If at the time of the countdown the START/PAUSE button
is pressed again the DELAY option is cancelled and the
selected program starts automatically.
The DELAY function cannot be set once a program has
been started.
DRAIN OUT
To stop and cancel the active cycle, the Drain Out
function can be used.
A long press of START/PAUSE button, will activate the
DRAIN OUT function. The active program will be stopped
and the water in the dishwasher will be drained out.
If an option is not compatible with the selected program see
PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times
and beeps will sound. The option will not be enabled.
5
EN
DAILY USE
1. CHECK WATER CONNECTION
Check that the dishwasher is connected to the water supply and that
the top is open.
2. SWITCH ON THE DISHWASHER
Press the ON/OFF button.
3. LOAD THE RACKS
(see LOADING THE RACKS)
4. FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
Select the most appropriate program in accordance with the type of
crockery and its soiling level (see PROGRAMS DESCRIPTION) by pressing
the P button.
Select the desired options (see OPTIONS AND FUNCTIONS).
6. START
Start the wash cycle by pressing the START/PAUSE button. When the
program starts you hear a beep.
7. END OF WASH CYCLE
The end of the wash cycle is indicated by beeps and the display shows
END. Open the door and switch off the appliance by pressing the
ON/OFF button.
Wait for a few minutes before removing the crockery - to avoid burns.
Unload the racks, beginning with the lower one.
The machine will switch off automatically during certain extended
periods of inactivity, in order to minimise electricity consumption.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly.
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: press and hold the ON/OFF button, the
machine will switch off.
Switch the machine back on using the ON/OFF button and select the
new wash cycle and any desired options; start the cycle by pressing the
START/PAUSE button.
ADDING EXTRA CROCKERY
Without switching off the machine, open the door (be ware of HOT
steam!) and place the crockery inside the dishwasher. Close the door
and press the START/PAUSE button the cycle will begin from the point
at which it was interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power cut,
the cycle stops. Once the door has been closed or the electricity supply
is restored, to start again the cycle from where it was interrupted, press
the START/PAUSE button.
For more information about the functions, you can request or download
from the WEB a Use & Care Guide by following the instructions on the last
page.
ADVICE AND TIPS
TIPS
Before loading the baskets, remove all food residues from the crockery
and empty the glasses. You do not need to rinse beforehand under
running water.
Arrange the crockery so that it is held in place firmly and does not tip
over; and arrange the containers with the openings facing downwards
and the concave/convex parts placed obliquely, thus allowing the
water to reach every surface and flow freely.
Warning: lids, handles, trays and frying pans do not prevent the
sprayer arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket
because in this sector the water sprays are stronger and allow a higher
washing performance.
After loading the appliance, make sure that the sprayer arms can rotate
freely.
HYGIENE
To avoid odour and sediment which can be accumulated in the
dishwasher please run a high temperature program at least one a
month. Use a tea spoon of detergent and run it without the loading to
clean your appliance.
UNSUITABLE CROCKERY
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique
crockery. Their decorations are not resistant.
• Parts in synthetic material which do not withstand high
temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can
change and fade during the washing process. Some types of glass (e.g.
crystal objects) can become opaque after a number of wash cycles too.
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as
dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the
wash cycle is over.
6
LOADING THE RACKS
UPPER RACK
Load delicate and light dishes: glasses, cups, saucers, low salad bowls.
(loading example for the upper rack)
ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper rack can be adjusted: high position to place
bulky crockery in the lower basket and low position to make the most
of the tip-up supports by creating more space upwards and avoid
collision with the items loaded into lower rack.
The upper rack is equipped with a
Upper Rack height adjuster
(see figure), without pressing the levers,
lift it up by simply holding the rack
sides, as soon as the rack is stable in its
upper position.
To restore to the lower position, press
the levers A at the sides of the rack and
move the basket downwards.
We strongly recommend that you do
not adjust the height of the rack
when it is loaded.
NEVER raise or lower the basket on
one side only.
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
The side foldable flaps can be positioned at
three different heights to optimize the
arrangement of crockery inside the rack.
Wine glasses can be placed safely in the foldable
flaps by inserting the stem of each glass into the
corresponding slots.
For optimum drying results incline the foldable
flaps more. To change the inclination, pull up
the foldable flap, slide it slightly and position it
as you wish.
LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids
should ideally be placed at the sides to avoid interferences with the
spray arm.
(loading example for the lower rack)
The lower rack has tip-up supports which can be used in a vertical
position when arranging plates or in a horizontal position (lower) to
load pans and salad bowls easily.
CUTLERY BASKET
The basket is equipped with top grilles
for improved cutlery arrangement. The
cutlery basket should be positioned
only at the front of the lower rack.
Knives and other utensils with sharp
edges must be placed in the cutlery
basket with the points facing
downwards or they must be
positioned horizontally in the tip-up
compartments on the upper rack.
7
EN
CARE AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
Regularly clean the filter assembly so that the filters do not clog and
that the waste water flows away correctly.
The filter assembly consists of three filters which remove food residues
from the washing water and then recirculate the water: to obtain the
best washing results, you need to keep them clean.
The dishwasher must not be used without filters or if the filter is
loose.
After several washes, check the filter assembly and if necessary clean it
thoroughly under running water, using a non-metallic brush and
following the instructions below:
1. Turn the cylindrical filter
A
in an anti-clockwise direction and pull it
out
(Fig 1)
.
2. Remove the cup filter
B
by exerting a slight pressure on the side
flaps
(Fig 2)
.
3. Slide out the stainless-steel plate filter
C
(Fig 3)
.
4. Inspect the trap and remove any food residues.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
CLEANING THE SPRAY ARMS
On occasions, food residue may become encrusted onto the spray arms
and block the holes used to spray the water. It is therefore
recommended that you check the arms from time to time and clean
them with a small non-metallic brush.
To remove the upper spray arm, turn the plastic locking ring in an anti-
clockwise direction. The upper spray arm should be replaced so that
the side with the greater number of holes is facing upwards.
The lower spray arm may be removed by pulling it upwards.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of
impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked and
damage the dishwasher.
A
A
B
C
12
34
8
TROUBLESHOOTING
MAINTENANCE AND TROUBLESHOOTING GUIDE
For more information, maintenance procedures and troubleshooting,
see the Use and Care Guide.
The Use and Care Guide can be obtained by:
• After-Sales Service; phone number see in warranty booklet.
• download from website: http://docs.whirlpool.eu
• use QR code:
TECHNICAL DATASHEET
The technical data containing the energy consumption data can be
downloaded from the website:
http://docs.whirlpool.eu
CONTACTING AFTER-SALES SERVICE
When you contact the After-Sales Service,
you must provide the codes shown on
the rating plate attached to the left or
right side inside the door of the
dishwasher. The phone number is listed
in the warranty booklet or on the website:
http://www.whirlpool.eu
Your dishwasher may not work properly.
Before contacting the Service Centre check if the problem can be solved by going through the following list.
PROBLEMS POSSIBLE CAUSES SOLUTIONS
The dishwasher
won’t start or does
not respond to com-
mands.
The appliance has not been plugged in
properly.
Insert the plug into the socket.
Power outage. The dishwasher starts automatically when the power returns.
The dishwasher door is not closed. Vigorously push the door until you hear the “click”.
It does not respond to commands. Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and reset the program.
The dishwasher
won’t drain.
The wash cycle has not finished yet. Wait until the wash cycle finishes.
The drain hose is bent. Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked. Clean the sink drain pipe.
The filter is clogged up with food residues Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishwasher
makes excessive
noise.
The dishes are rattling against each. Arrange the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Reset dish-
washer by pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and
run new program without detergent.
The dishes are not
clean.
The crockery has not been arranged prop-
erly.
Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being
hindered by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle. Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has
not been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged. Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt. Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
IEC 436
:
001
195144175.00
04/2016 - lr- Xerox Fabriano