Whirlpool WHE22333 User Manual
Displayed below is the user manual for WHE22333 by Whirlpool which is a product in the Freezers category. This manual has pages.
Related Manuals
INSTRUCTIONS FOR USE
EN
DIAGRAM OF THE APPLIANCE (Fig. 1)
A. Handle.
B. Safety lock (if provided).
C. Gasket.
D. Separator (if provided).
E. Defrost water drain plug.
F. Control panel.
G. Side motor cooling grille.
DIAGRAM OF THE CONTROL PANEL (Fig. 2)
1. Red light: when ashing, indicates an alarm condition
(see paragraph “TROUBLESHOOTING GUIDE”).
2. Blue light: when lit, indicates that the “6th Sense”
function is active (see paragraph “6th Sense function”).
3. Green lights: indicate that the product is running and
the temperature has been set.
4. Set temperature button: to adjust the set temperature
and to activate/deactivate fast freeze procedures.
BEFORE USING THE APPLIANCE
Your new appliance is designed to be used in the
household and similar applications such as:
- kitchen areas in shops, oces and other working
environments
- farm houses
- by clients in hotels, motels, residences, bed & breakfasts.
The product must only be used to store frozen food, to
freeze fresh food and to make ice.
Regulations require the appliance to be earthed. The
manufacturer declines all liability for injury to persons
or animals and for damage to property resulting
from failure to observe the above procedures and
reminders.
1. After unpacking, make sure that the appliance is
undamaged and that the door closes perfectly, with the
gasket remaining intact. Any damage must be reported
to your retailer within 24 hours after delivery of the
appliance.
2. Wait at least two hours before switching the appliance on
in order to ensure the refrigerant circuit is fully ecient.
3. Installation and electrical connection must be carried out
by a qualied technician, according to the manufacturer’s
instructions and local safety regulations.
4. Clean the inside of the appliance before using it.
• Before connecting the appliance to the mains supply,
ensure that the voltage corresponds to that given on
the rating plate located on the rear of the appliance.
• Electricalconnectionsmustbemadein
accordance with local regulations.
INSTALLATION
• Unpacktheappliance.
• Removethe4spacersinsertedbetweenthedoor
and the appliance. (Fig. 3)
• Make sure the defrost water drain plug (if provided) is
correctly positioned (E).
• For optimum appliance operation and to avoid damage
when the door is opened, leave a space of at least 7 cm
from the rear wall and 7 cm at the sides. (Fig. 4)
• Fit the accessories (if provided).
SWITCHING ON THE APPLIANCE
• Plug in the appliance.
• The green LED lights up (“Normal”).
• The blue LED lights up (6th Sense).
• The red LED ashes to indicate that the temperature
inside the appliance is not yet suciently low for food
storage. The red LED will normally switch o within the
rst six hours after the appliance is switched on.
• Place food inside the product only when the red LED has
switched o.
• The blue LED, “6th Sense” (2), stays on until the set
temperature is reached.
Note: Thanks to the ecient lid seal, the appliance lid will
not re-open easily immediately after closing. Wait a few
minutes before re-opening the lid of the appliance.
TEMPERATURE ADJUSTMENT
Use the key (4) to select the desired temperature.
To adjust the internal temperature, proceed as follows:
• Repeatedly press the key (4). Each time the key is
pressed, the set temperature is updated, displaying the
“Normal”, “Eco” and “Plus” values in succession.
• Select “Plus” for a colder storage temperature.
• With partial loads “Eco” is recommended: this setting will
optimize energy consumption.
Note: The settings will be saved in the memory even if a
power cut occurs. The time needed for the temperature
inside the freezer to reach the set value, can vary
depending on climatic conditions and the set temperature
itself.
‘6TH SENSE’ FUNCTION
This function will activate automatically in the following
cases:
• dooropening
This function activates every time the opening of the door
changes the internal temperature of the appliance. The
function remains active for the time needed to reinstate
optimum operating conditions.
• storingfoodinsidethefreezer
This function activates every time signicant quantities of
food are introduced. It remains active for the time needed
to reinstate optimum freezing conditions of the food
introduced, ensuring the best compromise between the
quality of the freezing process and energy consumption.
Note: The duration of the “6th Sense” function is set
automatically, and may vary depending on the way the
product is used.
FREEZING FOOD
Preparationoffreshfoodforfreezing
• Before freezing, wrap and seal fresh food in: aluminium
foil, cling lm, air and water-tight plastic bags,
polyethylene containers with lids, provided they are
suitable for freezing foods.
• Food must be fresh, mature and of prime quality in order
to obtain high quality frozen food.
• Fresh vegetables and fruit should preferably be frozen
as soon as they are picked to maintain the full original
nutritional value, consistency, colour and avour.
• Always leave hot food to cool before placing in the
appliance.
Freezingfreshfood
• Place foods to be frozen in direct contact with the walls
of appliance:
A) - foods to be frozen,
B) - foods already frozen.
• Avoid placing foods to be frozen in direct contact with
food already frozen.
• For best and fastest freezing, foods should be split into
small portions; this will also be useful when the frozen
items are to be used.
• If minimum quantities of food are introduced (up to 1/4
of the maximum freezing power stated on the rating
plate), the operation of the appliance will be controlled
automatically by the “6th Sense” function without any
need for intervention from the user.
• When freezing higher quantities of food, up to the
maximum freezing capacity of the appliance, indicated
on the rating plated, proceed as follows:
1. At least 24 hours before storing fresh foods inside the
product for freezing, activate the fast freezing function
by pressing (4) for approximately 3 seconds. The
green LEDS (3) ash in sequence.
2. Introduce the food to freeze inside the appliance, and
keep the door of the appliance closed for 24 hours.
After this period the food will be frozen.
The fast freezing function can be deactivated manually by
pressing (4).
If the fast freeze function is not manually deactivated, it
will be automatically deactivated by the appliance after
50 hours.
FOOD STORAGE
Refer to the table on the appliance.
Classicationoffrozenfoods
Load and classify the frozen foods; it is advisable
to indicate the storage date on the packs, to ensure
consumption before the expiry dates listed in months in
Fig. 6 for each type of food.
Adviceforstoringfrozenfood
When buying frozen food, make sure that:
• The packaging is intact (food in damaged containers
may have deteriorated). If a package is swollen or has
damp patches, the product may not have been stored
in optimum conditions and therefore undergone partial
defrosting.
• When shopping, leave frozen food purchases until last
and carry them in a thermally insulated bag.
• On arriving home, immediately place the frozen food in
the appliance.
• Avoid or minimise temperature variations. Observe the
expiry date on the packaging.
• Always follow the storage instructions on frozen food
packages.
Note:
Eat fully or partially defrosted foods immediately.
Donotrefreezeunlessthefoodiscookedafterithas
thawed.Oncecooked,thefoodcanberefrozen.
In case of a prolonged power failure:
• Do not open the appliance door, except to place ice
packs (if provided) over the frozen foods on the right and
left side of the appliance. This will slow down the rise
in temperature.
PRECAUTIONS AND SUGGESTIONS
• Duringinstallation,makesuretheappliancedoes
not damage the power cable.
• Do not store glass containers with liquids inside the
product as they may break.
• Do not eat ice cubes or ice lollies immediately after
taking them out of the appliance as they may cause cold
burns.
• Before carrying out any maintenance or cleaning, always
unplug the appliance or disconnect the power supply.
• Do not install the appliance in places exposed to direct
sunlight or near heat sources in order to avoid increasing
power consumption.
• Do not put aerosol spray cans or recipients containing
propellants or ammable substances in the appliance.
• Do not store or use gasoline or other ammable liquids
and gases in the vicinity of this or any other domestic
appliance. The fumes can create a re hazard or
explosion.
• Install the appliance in a perfectly horizontal position, on
a oor strong enough to take its weight and in an area
suitable for its size and use.
• Install the appliance in a dry, well-ventilated place.
The appliance is set for operation at specic ambient
temperature ranges, according to the climatic class
indicated on the data plate located at the rear of the
product (Fig. 7). The appliance may not work properly
if it is left for a long time at a temperature outside the
specied range.
• It is advisable to leave the appliance connected if left
empty even for short periods.
• Be careful not to damage the oors when you move the
appliance (e.g. parquet). To facilitate product handling, it
is advisable to empty it beforehand, if possible.
Note: The appliance must be handled and installed by two
or more persons.
• Do not use mechanical devices or any means other
than those recommended and/or supplied by the
manufacturer to speed up the defrosting process.
• Do not use electrical appliances inside the product,
unless such appliances are specically recommended by
the manufacturer.
• The bulb used inside the appliance is specically
designed for domestic appliances and is not suitable for
general room lighting within the home (EC Regulation
244/2009).
• This appliance must not be used by children under
8yearsofage,orbypeoplewithlimitedphysical,
sensory or mental abilities or without experience
andknowledgeofit,unlessinstructedinitsuseby
those responsible for their safety.
• Donotallowchildrentoplayorhideinsidethe
product:riskofbecomingtrappedinsideand
suocating.
• Powercablemodicationorreplacementmustonly
becarriedoutbyqualiedpersonnelorAfter-sales
Service.
• Donotuseextensionleadsoradapters.
• Electricaldisconnectionmustbepossibleeitherby
unpluggingtheapplianceorbymeansofadouble-
poleswitchlocateduplinefromthesocket.
• Ensurethatthevoltageindicatedontheappliance
data plate corresponds to the domestic supply
voltage.
• Donotingestthecontents(non-toxic)oftheice
packs(ifprovided).
• Restrictthenumberoftimesyouopenthedoor.
• Thisappliancefeatures“skincondenser”
technology: the condensing unit is integrated into
thewallsofthefreezer.Forthisreasonthesideand
front walls of the product may become hot while
the product is running. This is entirely normal and
alsoreducestheriskofcondensationformingin
particularly critical environmental conditions (see
paragraph“Troubleshootingguide”).
APPLIANCE DEFROSTING
The appliance should be defrosted when the thickness of
ice on the walls reaches 5-6 mm.
• Disconnect the appliance from the power supply.
• Remove food from the appliance and put it in a very cool
place or a thermally insulated bag.
• Leave the appliance door open.
• Remove the internal defrost water drain plug (depending
on model) (Fig. 8).
• Remove the external defrost water drain plug (depending
on model) and reposition it as shown in Fig. 8.
• Use the separator (depending on model) inside the
product as a recipient for any remaining water, (D) as
shown in Fig. 8. If there is no separator, use a shallow
container.
• Defrosting can be sped up by using a spatula to detach
the frost from the appliance walls.
• Remove the frost from the bottom of the appliance.
• In order to avoid permanent damage to the
applianceinterior,donotusepointedorsharp
metal instruments to remove the ice.
• Donotuseabrasiveproductsorheatuptheinterior
articially.
• Drytheinsideoftheappliancethoroughly.
• Ret the plug after defrosting.
CLEANING AND MAINTENANCE
• Remove the frost from the upper edges (see
Troubleshooting Guide).
• Clean the inside after defrosting, using a sponge
dampened with warm water and/or mild detergent.
• Clean the side vent (if provided).
Unplug the appliance before carrying out maintenance
operations.Donotuseabrasiveproducts,scourers
orstain-removers(e.g.acetone,trichloroethylene)to
clean the appliance.
Toobtainthebestresultsfromyourappliance,carry
out cleaning and maintenance at least once a year.
CHANGING THE LID LIGHT BULB (if provided)
• Disconnect the appliance from the mains power supply.
• Remove the diuser by following the sequence of steps
shown in the gure.
• Unscrew the light bulb and replace it with an identical
bulb of the same wattage and voltage.
• Ret the diuser and plug in the appliance.
TROUBLESHOOTING GUIDE
1.TheredLEDashes.
• Is there a power failure?
• Is a defrosting operation in progress?
• Has fresh food recently been introduced?
• Is the appliance lid properly closed?
• Is the appliance placed near a heat source?
• Are the ventilation grille and condenser clean?
2.AllLEDsashatthesametime.
• Contact the After-Sales Service.
3. The appliance is too noisy.
• Is the appliance perfectly horizontal?
• Is the appliance in contact with other furniture or
objects that may cause vibrations?
• Has the packaging been removed from under the
appliance?
Note: Gurgling noises from the refrigerating circuit after the
compressor cuts out are perfectly normal.
4.AllLEDsareoandtheproductisnotworking.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the electric cable intact?
5.AllLEDsareoandtheproductisworking.
• Contact the After-Sales Service.
6. The compressor runs continuously.
• Have hot foods been put in the appliance?
• Has the appliance lid been left open for a long time?
• Is the appliance placed in a very warm room or near
heat sources?
• Has the fast freeze function been activated? (the
green LEDS ash alternatively)
7. Too much ice on the upper edge.
• Are the defrost water drainage plugs correctly
positioned?
• Is the appliance lid properly closed?
• Is the appliance lid seal damaged or deformed?
(See chapter “Installation”)
• Have the 4 protection pieces been removed?
(See chapter “Installation”)
8. Formation of condensate on the external walls of
the appliance.
• It is normal for condensation to form under certain
atmospheric conditions (humidity above 85%) or if the
appliance is located in a damp or poorly ventilated
room. The performance of the appliance is in no way
aected.
9. The layer of ice on the internal walls of the
appliance is not uniform.
• This phenomenon is quite normal.
SAFEGUARDING THE ENVIRONMENT
1.Packing
The packing material is 100% recyclable and bears the
recycling symbol. For disposal, comply with the local
regulations. Keep the packing materials (plastic bags,
polystyrene parts, etc.) out of the reach of children, as they
are a potential source of danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable material.
This appliance is marked in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring the correct disposal of
this appliance, you can help prevent potentially negative
consequences for the environment and the health of
persons.
The symbol on the appliance, or on the accompanying
documents, indicates that this appliance should not be
treated as domestic waste but must be taken to a special
collection centre for the recycling of electrical and electronic
equipment.
When scrapping the appliance, make it unusable by cutting
o the power cable and removing the doors and shelves
so that children cannot easily climb inside and become
trapped.
Scrap the appliance in compliance with local regulations
on waste disposal, taking it to a special collection centre;
do not leave the appliance unattended even for a few days,
since it is a potential source of danger for children.
For further information on the treatment, recovery and
recycling of this product, contact your competent local
oce, the household waste collection service or the shop
where you purchased the appliance.
Information:
This appliance does not contain CFCs. The refrigerant
circuit contains R134a (HFC) or R600a (HC) (see the rating
plate inside the appliance).
Appliances with Isobutane (R600a): isobutane is a natural
gas without environmental impact, but is ammable.
Therefore, make sure the refrigerant circuit pipes are not
damaged.
This product may contain Fluorinated Greenhouse Gases
covered by the Kyoto Protocol; the refrigerant gas is inside
a hermetically sealed system.
Refrigerant gas: R134a has a Global Warming Potential of
(GWP) 1300.
Declaration of conformity
• This appliance has been designed for preserving food
and is manufactured in compliance with Regulation (CE)
No. 1935/2004.
• This appliance has been designed, manufactured and
marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/CE (which replaces 73/23/CEE and
subsequent amendments);
- the protection requirements of Directive “EMC”
2004/108/EC.
Electrical safety of the appliance can only be guaranteed if
it is correctly connected to an approved earthing system.
AFTER-SALESSERVICE
BeforecontactingAfter-SalesService:
1. See if you can solve the problem yourself.
2. Switch the appliance on again to see if the problem
has been solved. If it has not, disconnect the appliance
from the power supply and wait for about an hour before
switching on again.
3. If the problem persists after this course of action, contact
After-Sales Service.
Specify:
• the nature of the fault,
• the model,
• the service number (the number after the word SERVICE
on the rating plate on the rear of the appliance),
• your full address,
• your telephone number and area code.
1
345
2
6
8 9
CLASE/KLASSE
CLASSE/CLASS °C °F
SN 10 - 32 50 - 90
N16 - 32 61 - 90
ST 16 - 38 61 - 100
T16 - 43 61 - 110
7
1 2 3 4
5019 300 02681