Whirlpool WHE2535 F User Manual
Displayed below is the user manual for WHE2535 F by Whirlpool which is a product in the Freezers category. This manual has pages.
Related Manuals
INSTRUCTIONS FOR USE
EN
APPLIANCE DIAGRAM (Fig. 1)
A. Handle.
B. Safety closure (if provided).
C. Seal.
D. Separator (if provided).
E. Defrost water drain plug.
F. Control panel.
G. Side motor ventilation grille.
CONTROL PANEL DIAGRAM (Fig. 2)
1. Red light: when blinking, it indicates an alarm condition
(see the section “TROUBLESHOOTING GUIDE”).
2. Blue light: when on, it indicates that the STOP FROST
function is activated (see the section “STOP FROST
FUNCTION”)
3. Green lights: they indicate that the product is working,
the set temperature and possible activation of the quick
freeze function (“Shopping”).
4. Setting button: for updating the set temperature,
activation/deactivation of the quick freeze function
(“Shopping”) and activation/deactivation of the “STOP
FROST” function.
BEFORE USING THE APPLIANCE
Your new appliance is designed to be used in the
household and similar applications such as:
- kitchen areas in shops, oces and other working
environments
- farm houses
- by clients in hotels, motels, residences, bed &
breakfasts.
The product must only be used to store frozen food, to
freeze fresh food and to make ice.
Regulations require the appliance to be earthed. The
manufacturer declines all liability for injury to persons
or animals and for damage to property resulting
from failure to observe the above procedures and
reminders.
1. After unpacking, make sure that the appliance is
undamaged and that the door closes perfectly, with the
gasket remaining intact. Any damage must be reported
to your retailer within 24 hours after delivery of the
appliance.
2. Wait at least two hours before switching the appliance on
in order to ensure the refrigerant circuit is fully ecient.
3. Installation and electrical connection must be carried out
by a qualied technician, according to the manufacturer’s
instructions and local safety regulations.
4. Clean the inside of the appliance before using it.
• Before connecting the appliance to the mains supply,
ensure that the voltage corresponds to that given on the
rating plate located on the rear of the appliance.
• Electricalconnectionsmustbemadeinaccordance
with local regulations.
INSTALLATION
• Unpacktheproduct.
• Removethe4spacersinsertedbetweenthelidand
the product. (Fig. 3)
• Make sure the defrost water drain plug (if provided) is
correctly positioned (E).
• For optimum operation and to avoid damage when the
lid is opened, maintain a distance of at least 7 cm from
the front wall and 7 cm at the sides. (Fig. 4)
• Insert the accessories (if provided).
STARTING THE PRODUCT
• Connect the product to the power supply.
• The green light (“Normal”) comes on.
• The red light (1) blinks, since the temperature inside the
product is not yet low enough for loading food. This light
normally goes o within six hours after startup.
• Place food inside only when the red light has gone o.
Note: If the STOP FROST function is deactivated, the lid
cannot be immediately reopened after closing it, because
the seal is tight. It is necessary to wait a few minutes before
reopening the lid.
TEMPERATURE ADJUSTMENT
Use the button (4) to select the required temperature. To
adjust the product temperature, proceed as follows:
• Press the button (4). With each press of the button, the
set temperature will be changed cyclically between the
values “Eco”, “Normal”, “Intensive” and “Shopping”.
• Select “Intensive” for a colder storage temperature.
• In case of a partial load, it is advisable to select “Eco” to
optimise energy consumption.
The green lights (3) indicate the selected setting as follows:
Eco: less cold temperature
(left light on).
Normal: middle temperature
(right light on).
Intensive: very cold temperature
(both lights on).
Shopping: Quick Freeze
(both lights on blinking).
See the section “Freezing fresh
food”.
Note: In case of a power failure, the settings (except for
the “STOP FROST” function) remain stored. The time
required for the temperature inside the freezer to reach
approximately the set value may vary depending on the
climatic conditions and the setting selected.
STOP FROST FUNCTION
The STOP FROST function signicantly reduces the
amount of frost that can form inside the product, collecting
it in the special easy to remove and clean “ICE BOX” (M)
container. STOP FROST technology also allows easy
reopening of the lid at any time whenever deemed
necessary, even repeatedly, always with the same eort.
The STOP FROST function is already activated when the
product is switched on the rst time (blue light on). It can be
deactivated/reactivated by keeping the button (4) pressed
for at least 3 seconds.
Thanks to STOP FROST technology, the ambient humidity
is largely conveyed inside the ICE BOX (M), where it turns
into ice.
Makesuretoperiodicallyremovetheinsidethe
ICE BOX (M) following the cleaning procedure described
below. The frequency of cleaning operations required to
ensure proper functioning of the system depends on the
climatic conditions in the place of installation (more frequent
cleaning is advisable in places with high humidity). The lack
of or inadequate cleaning of the device can temporarily
compromise its operation. Therefore, during normal use
it is advisable to check the level of ice accumulated in
the Ice Box (M), also by means of the special inspection
window (I).
STOP FROST DEVICE CLEANING PROCEDURE
• Open the lid of the product.
• Grip the ICE BOX (M) with two hands and turn it
anticlockwise (g. S1), bringing the top indicator (H) from
the closed padlock to the open padlock position (g. S2),
then pull out the ICE BOX (g. S3).
• Remove any ice present inside the cone (L) on the lid
(free the middle hole of any obstructions), being careful
not to damage the surfaces.
• Dry the surfaces of the cone (L) on the lid with a soft
cloth.
• Close the lid.
• Remove the ice contained in the ICE BOX (M), washing
it with cold or lukewarm (not hot) water.
• Dry the inside and outside of the ICE BOX (M) with a soft
cloth.
• Ret the ICE BOX (M), positioning the top indicator (H)
at the open padlock then turn clockwise until aligning the
top indicator (H) with the closed padlock (reverse order
to that followed for removing the ICE BOX).
• Close the lid.
IF THE ICE BOX (H) IS BLOCKED OR HARD TO
REMOVE
If the ICE BOX (M) is blocked, do not persist in trying to
remove it, but proceed as follows:
• Close the lid and check if the STOP FROST function is
on or o.
- If the function is on (blue light on):
press the button (4) for 3 seconds to deactivate the
function (blue light o), then press the button (4) again
for 3 seconds; the STOP FROST function is reactivated
(blue light on).
- Ifthefunctioniso(bluelighto):
press the button (4) for 3 seconds: the STOP FROST
function is activated (blue light on).
• Wait about 25 minutes for completion of automatic
defrost, then try removing the ICE BOX (M) again by
following the “STOP FROST DEVICE CLEANING
PROCEDURE”.
FREEZING FOOD
Preparing fresh food for freezing
• Wrap and seal fresh food in: aluminium foil, cling lm, air
and water-tight plastic bags, polyethylene containers with
lids, provided they are suitable for freezing foods.
• Food must be fresh, mature and prime quality.
• Fresh vegetables and fruit should preferably be frozen
as soon as they are picked to maintain the full original
nutritional value, consistency, colour and avour.
• Always leave hot food to cool before placing in the
appliance.
Freezing fresh food
• Place foods to be frozen in direct contact with the walls
of the appliance:
A) - food to be frozen,
B) - food already frozen.
• Avoid placing foods to be frozen in direct contact with
food already frozen.
• For better and faster freezing, foods should be split into
small portions; this will also be useful when the frozen
items are to be used.
1. At least 24 hours before storing fresh food in the
appliance, activate fast freezing (“Shopping”) by
repeatedly pressing button (4) until both green indicator
lights (3) ash.
2. Place the food to be frozen inside the appliance and
keep the lid closed for 24 hours. Food will be fully frozen
after this period of time.
The fast freezing function (“Shopping”) can be deactivated
by pressing button (4) and selecting a dierent temperature
setting.
If the function is not deactivated manually, the appliance
automatically deactivates the function after 50 hours,
restoring the last setting selected (which was active for at
least 1 minute) before the “Shopping” setting was selected.
FOOD STORAGE
Refer to the table on the appliance.
Classicationoffrozenfoods
Load and classify the frozen foods; it is advisable
to indicate the storage date on the packs, to ensure
consumption before the expiry dates listed in months in
Fig. 6 for each type of food.
Advice for storing frozen food
When buying frozen food, make sure that:
• The packaging is intact (food in damaged containers
may have deteriorated). If a package is swollen or has
damp patches, the product may not have been stored
in optimum conditions and therefore undergone partial
defrosting.
• When shopping, leave frozen food purchases until last
and carry them in a thermally insulated bag.
• On arriving home, immediately place the frozen food in
the appliance.
• Avoid or minimise temperature variations. Observe the
expiry date on the packaging.
• Always follow the storage instructions on frozen food
packages.
Note:
• Eat fully or partially defrosted foods immediately.
Donotrefreezeunlessthefoodiscookedafterit
hasthawed.Oncecooked,thefoodcanberefrozen.
• In case of a prolonged power failure: Do not open
theappliancedoor,excepttoplaceicepacks
(if provided) over the frozen foods on the right and
left side of the appliance. This will slow down the
rise in temperature.
PRECAUTIONS AND SUGGESTIONS
• Duringinstallation,makesuretheappliancedoes
not damage the power cable.
• Do not store glass containers with liquids inside the
product as they may break.
• Do not eat ice cubes or ice lollies immediately after
taking them out of the appliance as they may cause cold
burns.
• Before carrying out any maintenance or cleaning,
always unplug the appliance or disconnect the power
supply.
• Do not install the appliance in places exposed to
direct sunlight or near heat sources in order to avoid
increasing power consumption.
• Do not put aerosol spray cans or recipients containing
propellants or ammable substances in the appliance.
• Do not store or use gasoline or other ammable liquids
and gases in the vicinity of this or any other domestic
appliance. The fumes can create a re hazard or
explosion.
• Install the appliance in a perfectly horizontal position, on
a oor strong enough to take its weight and in an area
suitable for its size and use.
• Install the appliance in a dry, well-ventilated place.
The appliance is set for operation at specic ambient
temperature ranges, according to the climatic class
indicated on the data plate located at the rear of the
product (Fig. 7). The appliance may not work properly
if it is left for a long time at a temperature outside the
specied range.
• It is advisable to leave the appliance connected if left
empty even for short periods.
• Be careful not to damage the oors when you move the
appliance (e.g. parquet). To facilitate product handling,
it is advisable to empty it beforehand, if possible.
Note: The appliance must be handled and installed by two
or more persons.
• Do not use mechanical devices or any means other
than those recommended and/or supplied by the
manufacturer to speed up the defrosting process.
• Do not use electrical appliances inside the product,
unless such appliances are specically recommended
by the manufacturer.
• The bulb used inside the appliance is specically
designed for domestic appliances and is not suitable for
general room lighting within the home (EC Regulation
244/2009).
• Thisappliancemustnotbeusedbychildrenunder
8yearsofage,orbypeoplewithlimitedphysical,
sensoryormentalabilitiesorwithoutexperience
andknowledgeofit,unlessinstructedinitsuseby
those responsible for their safety.
• Donotallowchildrentoplayorhideinsidethe
product:riskofbecomingtrappedinsideand
suocating.
• Powercablemodicationorreplacementmustonly
becarriedoutbyqualiedpersonnelorAfter-sales
Service.
• Donotuseextensionleadsoradapters.
• Electricaldisconnectionmustbepossibleeitherby
unpluggingtheapplianceorbymeansofadouble-
poleswitchlocateduplinefromthesocket.
• Ensurethatthevoltageindicatedontheappliance
data plate corresponds to the domestic supply
voltage.
• Donotingestthecontents(non-toxic)oftheice
packs(ifprovided).
• Restrictthenumberoftimesyouopenthedoor.
• Thisappliancefeatures“skincondenser”
technology: the condensing unit is integrated into
the walls of the freezer. For this reason the side
and front walls of the product may become hot
while the product is running. This is entirely normal
andalsoreducestheriskofcondensationforming
in particularly critical environmental conditions
(seeparagraph“Troubleshootingguide”).
APPLIANCE DEFROSTING
The appliance should be defrosted when the thickness of
ice on the walls reaches 5-6 mm.
• Disconnect the appliance from the power supply.
• Remove food from the appliance and put it in a very
cool place or a thermally insulated bag.
• Leave the appliance door open.
• Remove the internal defrost water drain plug (depending
on model) (Fig. 8).
• Remove the external defrost water drain plug
(depending on model) and reposition it as shown in
g. 8.
• Use the separator (depending on model) inside the
product as a recipient for any remaining water, (D) as
shown in g. 8. If there is no separator, use a shallow
container.
• Defrosting can be sped up by using a spatula to detach
the frost from the appliance walls.
• Remove the frost from the bottom of the appliance.
• Inordertoavoidpermanentdamagetothe
applianceinterior,donotusepointedorsharp
metal instruments to remove the ice.
• Donotuseabrasiveproductsorheatupthe
interiorarticially.
• Drytheinsideoftheappliancethoroughly.
• Ret the plug after defrosting.
CLEANING AND MAINTENANCE
• Remove the frost from the upper edges
(see Troubleshooting Guide).
• Clean the inside after defrosting, using a sponge
dampened with warm water and/or mild detergent.
• Clean the side vent (if provided).
Unplug the appliance before carrying out maintenance
operations.Donotuseabrasiveproducts,scourers
orstain-removers(e.g.acetone,trichloroethylene)to
clean the appliance.
Toobtainthebestresultsfromyourappliance,carry
out cleaning and maintenance at least once a year.
HANGING THE LID LIGHT BULB (if provided)
• Disconnect the appliance from the mains power supply.
• Remove the diuser by following the sequence of steps
shown in the gure.
• Unscrew the light bulb and replace it with an identical
bulb of the same wattage and voltage.
• Ret the diuser and plug in the appliance.
TROUBLESHOOTING GUIDE
1. Theredlightblinks.
• Is there a power failure?
• Is a defrost in progress?
• Is the lid closed properly?
• Is the product near a heat source?
• Are the ventilation grille and condenser clean?
2. Alltheindicatorlightsblinktogether.
• Contact the After-Sales Service.
3. Theproductisexcessivelynoisy.
• Is the product perfectly horizontal?
• Is the product touching other cabinets or objects that
can cause vibrations?
• Has the packing been removed from the base of the
product?
Note: A slight noise caused by circulation of the refrigerant
gas even after the compressor has stopped is quite normal.
4. Theindicatorlightsareoandtheproductdoes
notwork.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the electrical cable intact?
5. Theindicatorlightsareoandtheproductworks.
• Contact the After-sales Service.
6. The compressor runs continuously.
• Have hot foods been placed in the product?
• Has the lid been left open for a long time?
• Is the product in a very warm room or near a heat
source?
• Has the “Shopping” function been activated? (green
lights (3) blinking)
7. Too much ice on the top edges.
• Are the defrost water drain plugs correctly positioned?
• Is the lid closed properly?
• Is the lid seal damaged or twisted? (See the section
“Installation”)
• Have the 4 spacers been removed? (See the section
“Installation”)
• Is the STOP FROST function on?
• Are the ICE BOX (M) and cone (L) free of ice? Carry out
the “STOP FROST device cleaning procedure”
• Make sure the hole of the STOP FROST, located in the
outer rear edge of the lid, is not obstructed
8. Condensationontheexternalwallsoftheproduct.
• It is normal for condensation to form in certain climatic
conditions (humidity above 85%) or if the product
is located in a damp or poorly ventilated room. The
product’s operation is in no way aected.
9. The layer of frost on the internal walls of the
product is not uniform.
• This phenomenon is quite normal.
10. The ICE BOX does not collect ice.
• Make sure the hole of the STOP FROST, located in the
outer rear edge of the lid, is not obstructed.
SAFEGUARDING THE ENVIRONMENT
1.Packing
The packing material is 100% recyclable and bears the
recycling symbol . For disposal, comply with the local
regulations. Keep the packing materials (plastic bags,
polystyrene parts, etc.) out of the reach of children, as they
are a potential source of danger.
2. Scrapping/Disposal
The appliance is manufactured using recyclable material.
This appliance is marked in compliance with European
Directive 2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). By ensuring the correct disposal of
this appliance, you can help prevent potentially negative
consequences for the environment and the health of
persons.
The symbol on the appliance, or on the accompanying
documents, indicates that this appliance should not be
treated as domestic waste but must be taken to a special
collection centre for the recycling of electrical and electronic
equipment.
When scrapping the appliance, make it unusable by cutting
o the power cable and removing the doors and shelves
so that children cannot easily climb inside and become
trapped.
Scrap the appliance in compliance with local regulations
on waste disposal, taking it to a special collection centre;
do not leave the appliance unattended even for a few days,
since it is a potential source of danger for children.
For further information on the treatment, recovery and
recycling of this product, contact your competent local
oce, the household waste collection service or the shop
where you purchased the appliance.
Information:
This appliance does not contain CFCs. The refrigerant
circuit contains R134a (HFC) or R600a (HC) (see the rating
plate inside the appliance).
Appliances with Isobutane (R600a): isobutane is a natural
gas without environmental impact, but is ammable.
Therefore, make sure the refrigerant circuit pipes are not
damaged.
This product may contain Fluorinated Greenhouse Gases
covered by the Kyoto Protocol; the refrigerant gas is inside
a hermetically sealed system.
Refrigerant gas: R134a has a Global Warming Potential of
(GWP) 1300.
Declaration of conformity
• This appliance has been designed for preserving food
and is manufactured in compliance with Regulation (CE)
No. 1935/2004.
• This appliance has been designed, manufactured and
marketed in compliance with:
- safety objectives of the “Low Voltage” Directive
2006/95/CE (which replaces 73/23/CEE and
subsequent amendments);
- the protection requirements of Directive “EMC”
2004/108/EC.
Electrical safety of the appliance can only be guaranteed if
it is correctly connected to an approved earthing system.
AFTER-SALESSERVICE
BeforecontactingAfter-SalesService:
1. See if you can solve the problem yourself.
2. Switch the appliance on again to see if the problem
has been solved. If it has not, disconnect the appliance
from the power supply and wait for about an hour before
switching on again.
3. If the problem persists after this course of action, contact
After-Sales Service.
Specify:
• the nature of the fault,
• the model,
• the service number (the number after the word SERVICE
on the rating plate on the rear of the appliance),
• your full address,
• your telephone number and area code.
1
345
2
6
8 9
CLASE/KLASSE
CLASSE/CLASS °C °F
SN 10 - 32 50 - 90
N16 - 32 61 - 90
ST 16 - 38 61 - 100
T16 - 43 61 - 110
7
1 2 3 4
5019 300 02667