Whirlpool WHS2121 User Manual
Displayed below is the user manual for WHS2121 by Whirlpool which is a product in the Freezers category. This manual has pages.
Related Manuals
INSTRUCTIONS FOR USE
DESCRIPTION AND USE
DIAGRAM OF THE APPLIANCE (Fig. 1)
1. Lid handle.
2. Lock (if provided).
3. Seal.
4. Defrost water drain plug (depending on model).
5. Control panel.
6. Basket (depending on model).
7. Condenser (located at the rear).
INSTALLATION
• Refer to chapter “Before using the appliance”.
• Unpack the appliance.
• Remove the 4 protection pieces inserted
between lid and appliance (Fig 3).
• Warning: two of the four protection pieces must
be fitted in the seat of the condenser plastic
supports, located at the rear of the product
(Fig. 3).
This is necessary to ensure the correct distance from
the wall.
• Ensure that the defrosting water drainage plug (if
provided) is correctly positioned (4).
• For best operation of the appliance and in order to
avoid damage when the lid is opened, leave a space
of at least 7 cm from the rear wall and 7 cm at the
sides.
• Fit the accessories (if provided).
Clean the inside of the appliance before using it.
DIAGRAM OF THE CONTROL PANEL (Fig. 2)
a. Red LED: when flashing, it indicates that an alarm
condition is present see TROUBLESHOOTING GUIDE"
b. Green LEDS: they indicate that the appliance is in
operation, and the temperature has been set as
follows:
b1 less cold temperature (right light on), use this
setting with partial loads will optimize energy
consumption.
b2 middle temperature (center light on)
b3 very cold temperature (left light on)
ALL Green LEDs ON: FAST FREEZING function is
active; see the section “freezing fresh food”.
c. Temperature setting button: to adjust the set
temperature and to activate/deactivate the fast
freezing operations.
To select the desired temperature, repeatedly press
the setting button (3): each time the button is pressed,
the set temperature is updated.
To activate/deactivate fast freezing function, pressing
for approximately 3 seconds: all green LEDs flash
simultaneously 3 times and then remain lit.
Note:
The settings will be saved in the memory even if a
power cut occurs. The time needed for the
temperature inside the freezer to reach the set value,
can vary depending on climatic conditions and the set
temperature itself.
Switching on the appliance
• Plug in the appliance.
• The green LED lights up (middle temperature).
• The red LED flashes to indicate that the
temperature inside the appliance is not yet
sufficiently low for food storage. The red LED will
normally switch off within the first six hours after the
appliance is switched on.
• Place food inside the product only when the red
LED has switched off.
Note:
As the seal is tight, the appliance lid cannot be
reopened immediately after closing. Wait a few
minutes before re-opening the lid of the appliance.
FREEZING FOOD
Preparation of fresh food for freezing
• Before freezing, wrap and seal fresh food in:
Aluminium foil, cling film, air and water-tight plas tic
bags, polyethylene containers with lids, provided
they are suitable for freezing foods.
• Food must be fresh, mature and of prime quality in
order to obtain high quality frozen food.
• Fresh vegetables and fruit should preferably be
frozen as soon as they are picked to maintain the full
original nutritional value, consistency, colour and
flavour.
• Always leave hot food to cool before placing in the
appliance.
Freezing fresh food
• Place foods to be frozen in direct contact with the
walls of appliance (Fig. 4)
A) - foods to be frozen,
B) - foods already frozen.
• Avoid placing foods to be frozen in direct contact
with food already frozen.
• For best and fastest freezing, foods should be split
into small portions; this will also be useful when the
frozen items are to be used.
1. At least 24 hours before storing fresh foods inside
the product for freezing, activate the fast freezing
function by pressing button c for approximately 3
seconds. All green LEDs (b) comes on.
INSTRUCTIONS FOR USE
2. Introduce the food to freeze inside the appliance,
and keep the door of the appliance closed for 24
hours. After this period the food will be frozen. The
fast freezing function can be deactivated pressing
button c for approximately 3 seconds.
If the fast freeze function is not manually deactivated,
it will be automatically deactivated by the appliance
after 50 hours.
FOOD STORAGE
Refer to the table on the appliance.
Classification of frozen foods
Put the frozen products into the appliance and
classify them; the storage date should be indicated
on the packs, to allow use within expiry dates listed
in months in Fig. 5 for each type of food.
Advice for storing frozen food
When purchasing frozen food products:
• Ensure that the packaging is not damaged (frozen
food in damaged packaging may have deteriorated).
If the package is swollen or has damp patches, it
may not have been stored under optimal conditions
and defrosting may have already begun.
• When shopping, leave frozen food purchases until
last and transport the products in a thermally
insulated cool bag.
• Once at home, place the frozen foods immediately
in the appliance.
• Avoid, or reduce temperature variations to the
minimum Respect the best-before date on the
package.
• Always observe the storage information on the
package.
Note:
Eat fully or partially defrosted foods immediately.
Do not refreeze unless the food is cooked after it
has thawed. Once cooked, the thawed food can
be refrozen. If there is a long power failure:
• Do not open the appliance lid except to place
ice packs (if provided ) o ver the froz en foo ds on
the right and left of the appliance. This will slow
down the rise in temperature.
DEFROSTING THE APPLIANCE
The appliance should be defrosted when the
thickness of ice on the walls reaches 5-6 mm.
• Disconnect the appliance from the mains power
supply.
• Remove the packs of food from the appliance and
wrap them close together in newspaper and store in
a very cool place or thermally insulated bag.
• Leave the appliance lid open.
• Remove the internal defrost water drain plug
(depending on model) (Fig. 6)
• Remove the external defrost water drain plug
(depending on model) and reposition it as shown in
the figure 6.
• Place a bowl beneath the drainage channel to
collect the residual water. If available, use the divider
(Fig. 6)
• Speed up defrosting by using a spatula to detach
the ice from the appliance walls.
• Remove the ice from the bottom of the appliance.
• In order to avoid permanent damage to the
appliance interior, do not use pointed or sharp metal
instruments for removing the ice.
• Do not use abrasive products or heat up the interior
artificially.
• Dry the interior of the appliance thoroughly.
• On completion of the defrosting, refit the plug.
CARE AND MAINTENANCE
• Remove the ice from the upper edge (see the
Troubleshooting Guide).
• Clean the inside after defrosting, using a sponge
dampened with warm water and/or mild detergent.
• Clean the side motor cooling grille (depending on
model).
• Remove dust from the condenser on the rear of the
appliance.
Before carr ying out mai ntenance, unplug the
appliance.
Do not use abrasive products, scourers or stain-
removers (e.g. acetone, trichloroethylene) to
clean the appliance.
To obtain the best results from your appliance,
carry out cleaning and maintenance at least once
a year.
CHANGING THE LID LIGHT BULB (if provided)
• Disconnect the appliance from the mains power
supply.
• Remove the diffuser by following the sequence of
steps shown in the figure 7.
• Unscrew the light bulb and replace it with an
identical bulb of the same wattage and voltage.
• Refit the diffuser and plug in the appliance.
TROUBLESHOOTING GUIDE
1. The red LED flashes.
• Is there a power failure?
• Is a defrosting operation in progress?
• Is the appliance lid properly closed?
• Is the appliance placed near a heat source?
• Are the ventilation grille and condenser clean?
2. All LEDs flash at the same time.
• Contact the After-Sales Service.
3. The appliance is too noisy.
• Is the appliance perfectly horizontal?
INSTRUCTIONS FOR USE
• Is the appliance in contact with other furniture or
objects that may cause vibrations?
• Has the packaging been removed from under the
appliance?
Note: Gurgling noises from the refrigerating circuit
after the compressor cuts out are perfectly normal.
4. All LEDs are off and the prod uct is not
working.
• Is there a power failure?
• Is the plug properly inserted in the socket?
• Is the electric cable intact?
5. All LEDs are off and the prod uct is w or king.
• Contact the After-Sales Service.
6. The compressor runs continuously.
• Have hot foods been put in the appliance?
• Has the appliance lid been left open for a long
time?
• Is the appliance placed in a very warm room or
near heat sources?
• Has the fast freeze function been activated? (all
Green LEDs ON)
7. Too much ice on the upper edge.
• Are the defrost water drainage plugs correctly
positioned?
• Is the appliance lid properly closed?
• Is the appliance lid seal damaged or deformed?
(See chapter “Installation”)
• Have the 4 protection pieces been removed? (See
chapter “Installation”)
8. Formation of condensate on the external walls
of the appliance.
• It is normal for condensation to form under certain
atmospheric conditions (humidity above 85%) or if
the appliance is located in a damp or poorly
ventilated room. The performance of the appliance is
in no way affected.
9. The layer of ice on the internal walls of the
appliance is not uniform.
• This phenomenon is quite normal.
AFTER-SALES SERVICE
Before contacting After-Sales Ser vice:
1. See if you can solve the problem yourself.
2. Switch the appliance on again to see if the
problem has been solved. If it has not, disconnect
the appliance from the power supply and wait for
about an hour before switching on again.
3. If the problem persists after this course of action,
contact After-Sales Service.
Specify:
• the nature of the fault
• the model
• the service number (the number after the word
SERVICE on the rating plate on the rear of the
appliance)
• your full address
• your telephone number and area code.
ELECTRICAL CONNECTION FOR GREAT
BRITAIN AND IRELAND ONLY
Warning – thi s appli a nce must be earthed.
Fuse replacement
If the mains lead of this appliance is fitted with a BS
1363A 13amp fused plug, to change a fuse in this
type of plug use an A.S.T.A. approved fuse to BS
1362 type and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a
fuse and if the fuse cover is lost the plug must not be
used until a correct replacement is fitted.
Correct replacement are identified by the colour
insert or the colour embossed in words on the base
of the plug.
Replacement fuse covers are available from your
local electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain will
frequently apply, but a third type of plug and socket
is also used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet,
please contact After-sales Service for further
instruction.
Please do not attempt to change plug yourself. This
procedure needs to be carried out by a qualified
technician incompliance with the manufactures
instructions and current standard safety regulations.
.
400011227339