Table of Contents
Acer P6605 User Manual
Displayed below is the user manual for P6605 by Acer which is a product in the Data Projectors category. This manual has pages.
Related Manuals
Acer Projector
P6600/P6605/F261/PM-WU01/P6500/
P6505/F251/PM-801/P6200/F211/
PM-X01/P6200S/F211S/PM-X01S
Series
User's Guide
Changes may be made periodically to the information in this publication without obligation
to notify any person of such revisions or changes. Such changes will be incorporated in new
editions of this manual or supplementary documents and publications. This company makes
no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims the implied warranties of merchantability or fitness for a
particular purpose.
Record the model number, serial number, purchase date and place of purchase information in
the space provided below. The serial number and model number are recorded on the label
affixed to your projector. All correspondence concerning your unit should include the serial
number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronically, mechanically, by photocopy, recording or otherwise,
without the prior written permission of Acer Incorporated.
Model number: _________________________________
Serial number: __________________________________
Date of purchase: _______________________________
Place of purchase: ______________________________
Copyright © 2015. Acer Incorporated.
All Rights Reserved.
Acer Projector User's Guide
Original Issue: 08/2015
Acer and the Acer logo are registered trademarks of Acer Incorporated. Other companies' product
names or trademarks are used herein for identification purposes only and belong to their respective
companies.
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC."
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•Install the power supply unit before connecting the power cord to the AC
power outlet.
•Unplug the power cord before removing the power supply unit from the
projector.
•If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•Do not use this product near water.
•Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
•Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
•To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
•Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
•Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
•If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
•Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
•This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
v
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•the power cord or plug is damaged, cut or frayed
•liquid was spilled into the product
•the product was exposed to rain or water
•the product has been dropped or the case has been damaged
•the product exhibits a distinct change in performance, indicating a need
for service
•the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
•Turn on the projector first and then signal sources
•Do not place the product in following environments:
• Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
• Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
• Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
• Locations near fire alarms.
• Locations with an ambient temperature above 40 ºC/104 ºF.
• Locations where the altitudes are higher than 10000 feet.
•Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
•Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
•Do not face the projector lens to the sun. It can lead to fire.
vi
•When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
•Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
•Do not touch air outlet grille and bottom plate which becomes hot.
•Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
•Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
•Always open the lens shutter or remove the lens cap when the projector is
on.
•Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
•The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
•Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
•Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
•The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
•When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
•Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
•Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
•Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
•This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
• The projector should be placed in a horizontal way by means of desktop or
ceiling mount mode only, and its tilt angles should not exceed 6 degrees,
otherwise it would cause dramatical decrease of lamp life or severe safety
concern of system malfunction.
6°
6°
vii
Caution for Listening
To protect your hearing, follow these instructions.
•Increase the volume gradually until you can hear clearly and comfortably.
•Do not increase the volume level after your ears have adjusted.
•Do not listen to music at high volumes for extended periods.
•Do not increase the volume to block out noisy surroundings.
•Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal
information, check www.lamprecycle.org
Do not stare into the beam, RG2
"As with any bright source, do not stare into the direct beam, RG2 IEC 62471-
5:2015"
“Lamp(s) contain Mercury,
Dispose Properly.”
RG2
viii
First things first
Usage Notes
Do:
•Turn off the product before cleaning.
•Use a soft cloth moistened with mild detergent to clean the display
housing.
•Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•Block the slots and openings on the unit provided for ventilation.
•Use abrasive cleaners, waxes or solvents to clean the unit.
•Use under the following conditions:
•In extremely hot, cold or humid environments.
•In areas susceptible to excessive dust and dirt.
•Near any appliance that generates a strong magnetic field.
•Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
•To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•Please do not open or disassemble the product as this may cause electric shock.
•When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
•This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
•Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
•When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•Turn on the projector first and then the signal sources.
•Do not use lens cap when projector is in operation.
•When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Information for your safety and comfort iii
First things first viii
Usage Notes viii
Precautions viii
Introduction 1
Product Features 1
Package Overview 3
Projector Overview 4
Projector Outlook 4
Control Panel 6
Remote Control Layout 7
MHL (Mobile High-Definition Link) Control 9
Getting Started 10
Connecting the Projector 10
Turning the Projector On/Off 12
Turning on the Projector 12
Turning the projector off 13
Adjusting the Projected Image 14
Adjusting the Height of Projected Image 14
How to optimize image size and distance 15
How to get a preferred image size by
adjusting distance and zoom 18
How to get a preferred image position by
adjusting lens shift 21
User Controls 23
Installation menu 23
Onscreen Display (OSD) Menus 25
Color 26
Image 28
Setting 30
Management 32
Audio 33
3D 34
Contents
Language 34
Acer LAN webpage management 35
How to login in 35
Home 36
Control Panel 36
Network Setting 37
Alert Setting 37
Logout 38
Appendices 39
Troubleshooting 39
LED & Alarm Definition Listing 43
How to install cable management 44
Cleaning and replacing the dust filters 45
Replacing the Lamp 46
Ceiling Mount Installation 48
Specifications 51
Compatibility modes 53
Regulations and safety notices 58
1
English
Introduction
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
•DLP® technology
•P6200/F211/PM-X01/P6200S/F211S/PM-X01S series: Native 1024 x 768 XGA
resolution
P6500/P6505/F251/PM-801 series: 1920x1080 1080p resolution
P6600/P6605/F261/PM-WU01 series: True 1920x1200 WUXGA resolution
Full/4:3/16:9/L.Box aspect ratio supported
•Enables projecting 3D content via DLP Link Technology: Blue-Ray 3D
supported and nVidia 3DTV Play Ready
•Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
images
•High brightness and contrast ratio
•Acer LumiSense+ technology can intelligently optimizes the brightness and
color saturation of projected image based on actual ambient light.
•Versatile display modes (Bright, Presentation, Standard, Video, User)
enable optimum performance in any situation
•NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
•Lower power consumption and economy (ECO) mode extend lamp life
•Acer EcoProjeciton Technology delivers Intelligent power management
approach and physical efficiency improvement
•Equipped with HDMI™ & MHL connection supporting HDCP
•Support HDMI CEC function
•Advanced digital keystone and 4-corner correction optimizes presentations
•Smart detection delivers quick, intelligent source detection
•Multi-language onscreen display (OSD) menus
•Manual focus projection lens zooms up to 1.36x / 1.59x
•2x digital zoom and pan function
•Microsoft® Windows® 2000, XP, Vista®, Windows 7, Windows 8,
Macintosh® OS compliant
•Support MHL V2.0 signal display
•Support LumiSense+
•Built-in Two 10 Watts speaker
•Manual lens vertical shift adjustment
•Cable management
2
English
Note: Functions vary depending on model definition.
3
English
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable
Security card User’s guide Quick start guide
Carrying case Dust filters
(option)
Remote control
2 x Batteries
(option)
Cable management cover WirelessHD-Kit
(option)
WirelessCAST
(option)
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
MODE
RESYNC
LAMP TEMP
SETUP
MEDIA
3D
HOME
3D
MEDIA
SETUP
INFO
DC 5V IN
MHL HDMI
4
English
Projector Overview
Projector Outlook
Front / upper side
#Description #Description
1 Dust filter cover 7 Lamp cover
2 Control panel 8 Projection lens
3 Power button 9 Lens Cap
4 Zoom lever 10 Tilt adjusting wheels
5 Lens shift control ring 11 Ambient light sensor
6 Focus ring 12 Remote control receiver
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
MODE
RESYNC
LAMP TEMP
2
37 456
10
12
11
9
8
1
5
English
Right / Rear side
Note: Functions vary depending on model definition.
#Description #Description
1 Power socket 11 RS232 connector
2 5V DC output connector 12 YPbPr/YCbCr input connector
3 HD BaseT 13 S-Video input connector
4 LAN (RJ45 Port for 10/100M Ethernet) 14 Composite video input connector
5 Mini USB Ctrl connector (for firmware
upgrade and USB display)
15 Audio in connector (RCA)
6 Kensington™ lock port 16 Audio in connector
7 HDMI 2 connector 17 Audio out connector
8 HDMI/MHL connector (HDMI/MHL,
HDMI 1/MHL) 18 12V DC output connector
9 PC analog signal/HDTV/component
video input connector (VGA, VGA IN,
VGA IN 1, VGA IN 2)
19 3.5mm Microphone Input
10 Monitor loop-through output
connector (for VGA IN 1 only)
HDBaseT
1/MHL
DC 5V OUT LAN Min-USB VGA IN 1 VGA OUT
2
YS-VIDEO
VIDEO
AUDIO IN L
AUDIO IN
MIC-IN
AUDIO OUT
AUDIO IN R
Pr/Cr
Pb/Cb
RS232
VGA IN 2
12V DC
4 13 16
2 3 116
17
1819
14
9 101 5 87 12 15
6
English
Control Panel
Note: Functions vary depending on model definition.
#Icon Function Description
1 Four directional select
keys Use to select items or make
adjustments to your selection.
2MENU •Press "MENU" to launch the Onscreen
display (OSD) menu, back to the
previous step for the OSD menu
operation or exit the OSD menu.
•Confirm your selection of items.
3 SOURCE Changes the active source.
4 LAMP Lamp Indicator LED
5 TEMP Temp Indicator LED
6 RESYNC Automatically synchronizes the projector
to the input source.
7MODE Press "MODE" to select the display mode.
8 Keystone Adjusts the image to compensate for
distortion caused by tilting the projector.
9POWER •Power Indicator LED
•See the contents in "Turning the
Projector On/Off" section.
SOURCE
MENU MODE
RESYNC
LAMP TEMP
13
7
9
2
6
4 5
8
7
English
Remote Control Layout
#Icon Function Description
1 Infrared
transmitter
Sends signals to the projector.
2Laser pointer Aim the remote at the viewing screen.
3 POWER Please see "Turning the Projector On/Off" section.
4 HIDE Temporarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
5FREEZE Pause the screen image.
6 MEDIA_SETUP No function.
7 SOURCE Changes the active source.
8 3D Press "3D" to select 3D models.
9 ZOOM Zooms the projector display in or out.
10 BACK Press "BACK" to go back one menu step.
11 Laser button Aim the remote at the viewing screen, press and hold this
button to activate the laser pointer.
This function is not supported in Japanese market.
12 Enter No function.
13 Four directional
select keys
Use up, down, left, right buttons to select items or make
adjustments to your selection.
14 KEYSTONE Adjusts the image to compensate for distortion caused by
tilting the projector (± 30 degrees).
SETUP
MEDIA
3D
HOME
3D
MEDIA
SETUP
INFO
2
4
7
11
23
24
6
9
26
30
28
13
1
3
10
8
12
14
19
31
5
20
18
22
25
29
27
16
15
17
21
8
7
23
32
33
34 6
17
8
English
Note: Functions vary depending on model definition.
15 MENU •Press "MENU" to launch the Onscreen display (OSD)
menu, back to the previous step for the OSD menu
operation or exit the OSD menu.
•Confirm your selection of items.
16 MOUSE_Left/
Right Click
Left-/right-click buttons are on the left and right,
respectively; the center button works as a multidirectional
pointer stick. To enable this function, an USB cable must be
connected to projector from your PC.
17 MOUSE_Four
directional select
keys
18 MODE Press "MODE" to select the display mode.
19 VOLUME +/- Increases/decreases the volume.
20 PAGE For computer mode only. Use this button to select the next
or previous page. This function is only available when
connected to a computer via a USB cable.
21 Prev No function.
Next No function.
Play/Pause No function.
Stop No function.
22 VGA Press "VGA" to change source to the VGA connector. This
connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
23 S-VIDEO To change source to S-Video.
24 INFO No function.
25 COMPONENT Press "COMPONENT" to change source to Component
video. This connection supports YPbPr (480p/576p/720p/
1080i) and YCbCr (480i/576i).
26 VIDEO To change source to COMPOSITE VIDEO.
27 SD/USB A No function.
28 USB B For USB control and firmware upgrade.
29 HDMI™/DVI Press "HDMI™/DVI" to change source to HDMI™ (no DVI
function).
30 LAN/WiFi Press "LAN/WiFi" to display the image which is wire or
wirelessly transmitted from the PC to the projector via the
"Acer LAN webpage management" utility.
31 KeyPad 0~9 Press "0~9" to input a password in the "Security".
32 ASPECT RATIO Choose the desired aspect ratio.
33 RESYNC Automatically synchronizes the projector to the input
source.
34 MEDIA_HOME No function.
#Icon Function Description
9
English
MHL (Mobile High-Definition Link) Control
Note: Functions vary depending on model definition.
#Icon Component Description
1MODE
•Press "MODE" button for one second to activate the
MHL Control Mode.
•To exit, press the "MODE" button again.
2 SOURCE Press the "SOURCE" button to toggle between Navigation
or Numeric mode.
3 MENU Press to launch the root memu.
(only for Navigation mode)
4 Direction Keys Use up, down, left, right buttons to select items or make
adjustments to your selection.
(only for Navigation mode)
5 Select To select the file. (only for Navigation mode)
6 Exit To exit the file. (only for Navigation mode)
7 PgUp/PgDn Use the button to select the next or previous
page. (only for Navigation mode)
8 KeyPad 0~9 Number buttons. (only for Numeric mode)
HIDE
MEDIA
SETUP
MODE
SOURCE
ZOOM
FREEZE
SETUP
MEDIA
3D
HOME
8
5
6
4
2
1
3
7
10
English
Getting Started
Connecting the Projector
#Description #Description
1 Power cord 9 Composite video cable
2 USB cable for charging device 10 Audio cable Jack/RCA
3 LAN cable 11 12V DC cable
4 MHL cable (MicroUSB to HDMI) 12 Microphone cable
5 HDMI cable 13 RS232 cable
6 VGA cable 14 USB cable
7 VGA to component/HDTV adapter 15 3 RCA component cable
8 S-Video cable
HDBaseT
1/MHL
DC 5V OUT LAN Min-USB VGA IN 1 VGA OUT
2
YS-VIDEO
VIDEO
AUDIO IN L
AUDIO IN
MIC-IN
AUDIO OUT
AUDIO IN R
Pr/Cr
Pb/Cb
RS232
VGA IN 2
12V DC
RS232
RS232
13
RS232
HDTV adapter
7
15
RBG
RBG
D-Sub
D-Sub
6
HDMI
HDMI
5
HDMI
HDMI
5
USB
USB
14
HDMI
4
USB
MHL
R
W
10
R
W
10
D-Sub
D-Sub
6
8
12
R
W
W
R
10
3
2
2
Y
Y
9
11
RGB
15
RGB
1
Video output
DVD player,
Set-top Box,
HDTV receiever
DVD player
Internet
Power Bank
DVD player
DVD player,
Set-top Box,
HDTV receiever
Smart Phone
S-Video output
11
English
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: Functions vary depending on model definition.
Note: USB cable needs powered extender if the length is over 5 m.
Note: Some smartphones require a converter (supplied by
smartphone maker) to enable the MHL function.
Note: Before connecting the projector, remove the cable
management, refer to "Removing the cable management"
section.
Note: DC 12V out connector support 12V/100mA power for screen
control only.
Note: USB DC 5V out connector support 5V/1.5A power output for
power bank charging only when MHL source is not detected.
12
English
Turning the Projector On/Off
Turning on the Projector
1 Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
2 Turn on the projector by pressing "Power" button on the control panel or
remote control, and the Power indicator LED will turn blue.
3 Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
• If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.
• If the screen displays "No Signal", please make sure the signal cables
are securely connected.
• If you connect to multiple sources at the same time, use the "Source"
button on either control panel or the remote control or direct source
key on the remote control to switch between inputs.
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
MODE
RESYNC
LAMP TEMP
Power button
13
English
Turning the projector off
1 To turn the projector off, press and hold the power button. This message
appears: "Please press the power button again to complete the shutdown
process." Press the power button again.
2 The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 2 minutes to
ensure that the system cools properly. (only supported under "Instant
Resume" mode)
3 As long as the power cord remains plugged in, you can press the power
button to turn the projector immediately back on anytime during the 2-
minute shutdown process. (only supported under "Instant Resume" mode)
4 Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
5 It is now safe to unplug the power cord.
Warning indicators:
•"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
•"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or
service center.
Note: Functions vary depending on model definition.
Attention! The projector will enter a two minute cool down
period to ensure continued optimal lamp operation.
14
English
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise/lower the image:
Use Tilt adjusting wheel to fine-tune the display angle.
Tilt adjusting wheel
15
English
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.
•XGA series
If the projector is 2.0 m from the screen, good image quality is possible for
image sizes between 52" and 70".
Note: Remind as below figure, the space of 123 cm height is
required when located at 2 m distance.
Desired
Distance
(m)
<A>
Screen size Top Screen size Top
(Min zoom) (Max zoom)
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to
top of image
(cm)
<C>
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to top
of image (cm)
<C>
1.0 26 52 x 39 45 35 71 x 53 61
1.5 39 79 x 59 68 53 107 x 80 92
2.0 52 105 x 79 91 70 143 x 107 123
2.5 65 131 x 98 113 88 178 x 134 154
3.0 78 157 x 118 136 105 214 x 160 184
3.5 90 184 x 138 158 123 249 x 187 215
4.0 103 210 x 157 181 140 285 x 214 246
4.5 116 236 x 177 204 158 321 x 241 277
5.0 129 262 x 197 226 175 356 x 267 307
6.0 155 315 x 236 272 210 428 x 321 369
7.0 181 367 x 276 317 246 499 x 374 430
8.0 207 420 x 315 362 281 570 x 428 492
8.6 222 451 x 339 389 302 613 x 460 529
Zoom Ratio: 1.36x
70"
52"
2"
2"
52"
52"
2
2"
A
C
B
Height: 123 cm
from base to top
of image
Height:
91 cm
2.0 m
Desired Distance
Max screen size
Min screen size
16
English
•1080p series
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 60" and 96".
Note: Remind as below figure, the space of 139 cm height is
required when located at 3 m distance.
Desired
Distance
(m)
<A>
Screen size Top Screen size Top
(Min zoom) (Max zoom)
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to
top of image
(cm)
<C>
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to top
of image (cm)
<C>
1.0 20 45 x 25 29 32 71 x 40 46
1.5 30 67 x 38 44 48 106 x 60 69
2.0 40 89 x 50 58 64 142 x 80 93
2.5 50 112 x 63 73 80 177 x 100 116
3.0 60 134 x 75 87 96 213 x 120 139
3.5 71 156 x 88 102 112 248 x 140 162
4.0 81 179 x 100 117 128 284 x 160 185
5.0 101 223 x 126 146 160 355 x 199 231
6.0 121 268 x 151 175 192 426 x 239 278
7.0 141 313 x 176 204 224 496 x 279 324
8.0 161 357 x 201 233 256 567 x 319 370
9.0 181 402 x 226 262 288 638 x 359 416
9.4 190 420 x 236 274 301 667 x 375 435
Zoom Ratio: 1.59x
96"
60"
60"
0
A
C
B
Height: 139 cm
from base to top
of image
Height:
87 cm
3 m
Desired Distance
Max screen size
Min screen size
17
English
•WUXGA series
If the projector is 3.0 m from the screen, good image quality is possible for
image sizes between 62" and 99".
Note: Remind as below figure, the space of 142 cm height is
required when located at 3.0 m distance.
Desired
Distance
(m)
<A>
Screen size Top Screen size Top
(Min zoom) (Max zoom)
Diagonal
(inch)
<B>
W (cm) x H (cm)
From base
to top of
image (cm)
<C>
Diagonal
(inch)
<B>
W (cm) x H (cm)
From base to
top of image
(cm)
<C>
1.0 21 45 x 28 30 33 71 x 44 47
1.5 31 67 x 42 45 49 106 x 66 71
2.0 41 89 x 56 60 66 142 x 89 95
2.5 52 112 x 70 75 82 177 x 111 119
3.0 62 134 x 84 90 99 213 x 133 142
3.5 73 156 x 98 104 115 248 x 155 166
4.0 83 179 x 112 119 132 284 x 177 190
5.0 104 223 x 140 149 165 355 x 222 237
6.0 124 268 x 167 179 198 426 x 266 285
7.0 145 313 x 195 209 230 496 x 310 332
8.0 166 357 x 223 239 263 567 x 355 379
9.0 187 402 x 251 269 296 638 x 399 427
9.2 191 411 x 257 275 303 652 x 408 436
Zoom Ratio: 1.59x
99"
62"
62"
62"
A
C
B
Height: 142 cm
from base to
top of image
Height:
90 cm
3.0 m
Desired Distance
Max screen size
Min screen size
18
English
How to get a preferred image size by adjusting
distance and zoom
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.
•XGA series
To obtain an image size of 50" set the projector at a distance 1.4 m and 1.9 m
from the screen.
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
<A> W (cm) x H (cm) Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
20 53 x 40 1.0 46
40 81 x 61 1.1 1.5 70
50 102 x 76 1.4 1.9 88
60 122 x 91 1.7 2.3 105
70 142 x 107 2.0 2.7 123
80 163 x 122 2.3 3.1 140
90 183 x 137 2.6 3.5 158
100 203 x 152 2.9 3.9 175
120 244 x 183 3.4 4.6 210
150 305 x 229 4.3 5.8 263
180 366 x 274 5.1 7.0 315
200 406 x 305 5.7 7.7 351
250 508 x 381 7.1 9.7 438
300 610 x 457 8.6 526
Zoom Ratio: 1.36x
A
C
D
B
Desired Distance
1.9 m
1.4 m
Height: 88 cm
from base to top
of image
50"
Desired image
size
19
English
•1080p series
To obtain an image size of 60" set the projector at a distance 1.9 m and 3.0 m
from the screen.
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
<A> W (cm) x H (cm) Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
20 44 x 25 1.0 29
40 89 x 50 1.2 2.0 58
50 111 x 62 1.6 2.5 72
60 133 x 75 1.9 3.0 87
70 155 x 87 2.2 3.5 101
80 177 x 100 2.5 4.0 116
90 199 x 112 2.8 4.5 130
100 221 x 125 3.1 5.0 144
120 266 x 149 3.7 6.0 173
150 332 x 187 4.7 7.4 217
180 398 x 224 5.6 8.9 260
200 443 x 249 6.2 9.9 289
250 553 x 311 7.8 12.4 361
300 664 x 374 9.4 433
Zoom Ratio: 1.59x
A
C
D
B
Desired Distance
3.0 m
1.9 m
Height: 87 cm
from base to top of
image
60"
Desired
image size
20
English
•WUXGA series
To obtain an image size of 60" set the projector at a distance 1.8 m and 2.9 m
from the screen.
Desired Image Size Distance (m) Top (cm)
Diagonal (inch)
<A> W (cm) x H (cm) Max zoom
<B>
Min zoom
<C>
From base to top of
image
<D>
20 43 x 27 1.0 29
40 86 x 54 1.2 1.9 58
50 108 x 67 1.5 2.4 72
60 129 x 81 1.8 2.9 86
70 151 x 94 2.1 3.4 101
80 172 x 108 2.4 3.9 115
90 194 x 121 2.7 4.3 130
100 215 x 135 3.0 4.8 144
120 258 x 162 3.6 5.8 173
150 323 x 202 4.6 7.2 216
180 388 x 242 5.5 8.7 259
200 431 x 269 6.1 9.6 288
250 538 x 337 7.6 12.1 360
300 646 x 404 9.1 432
Zoom Ratio: 1.59x
A
C
D
B
Desired Distance
2.9 m
1.8 m
Height: 86 cm
from base to top
of image
60"
Desired
image size
21
English
How to get a preferred image position by adjusting
lens shift
The projector is equipped with lens shift for adjusting the position of projected
image up and down without requiring you to physically move the projector.
Note: The figures shown in this section are for reference only not
approximate value. The figures between units can be different
due to assembly tolerance.
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
MODE
RESYNC
LAMPTEMP
ZOOM
FOCUS
LENS SHIFT
Vertical Lens
Shift ring
22
English
P6200/P6200S Series:
The vertical height can be adjusted between -2% and 15% of the image height.
(The typical vertical image offset is fixed at 15% of the image height above the
center of the projector lens.)
P6500/P6505 Series:
The vertical height can be adjusted between -1% and 16% of the image height.
(The typical vertical image offset is fixed at 16% of the image height above the
center of the projector lens.)
P6600/P6605 Series:
The vertical height can be adjusted between -6% and 7% of the image height.
(The typical vertical image offset is fixed at 7% of the image height above the
center of the projector lens.)
Offset P6200/P6200S P6500/P6505 P6600/P6605
max [A] min [B] max [A] min [B] max [A] min [B]
V 15% -2% 16% -1% 7% -6%
H
V
V
SOURCE
MENU MODE
RESYNC
LAMP TEMP
FOCUS
LENS SHIFT
ZOOM
Offset max=V x [A]
Offset min=V x [B]
23
English
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .
1 Turn on the projector by pressing "Power" button on the control pad.
2 Press the "MENU" button on the remote control to launch the OSD for
projector installation and maintenance.
3 The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
4 The Installation menu includes the following options:
•Projection method
•Projection
•Projection Location
•Auto Keystone settings
•Manual Keystone settings
•H. Keystone
•V. Keystone
•LAN/WiFi
•LAN
•LAN IP/Mask
•Wireless HD dongle settings
•Language settings
•DC 5V Out (Standby)
24
English
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5 Push the MENU button anytime to exit the menu and return to the Acer
welcome screen.
Note: Functions vary depending on model definition.
25
English
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•To open the OSD menu, press "MENU" on the remote control or control
panel.
•When the OSD is displayed, use the keys to select any item in the
main menu. After selecting the desired main menu item, press to enter
submenu for feature setting.
•Use the keys to select the desired item and adjust the settings by
using the keys.
•Select the next item to be adjusted in the submenu and adjust as described
above.
•Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
•To exit OSD, press "MENU" on the remote control or control panel. The
OSD menu will close and the projector will automatically save the new
settings.
Note: Some of the following OSD settings may not be available. Please
refer to the actual OSD of your projector.
Note: Functions vary depending on model definition.
Main menu
Sub menu
Setting
26
English
Color
LumiSense+The light sensor of LumiSense+ technology can intelligently
optimize the brightness and color saturation of projected image
based on actual ambient light. The feature greatly enhances dark
detail visibility and color saturation.
•Off: For normal mode. (ambient light sensor is off)
•Auto Bright: Light sensor is on to automatically detect
ambient light and optimize the brightness and color
saturation of projected image.
•Dynamic Black:automatically optimize the display of dark
movie scenes enabling them to be shown in incredible detail.
Display Mode There are many factory presets optimized for various types of
images.
•Bright: For brightness optimization.
•Presentation: For meeting presentation.
•Standard: For common environment.
•Video: For playing video in a bright environment.
•Game: For game content.
•Education: For education environment.
•Movie: For brighter and general movie/video/photo playing.
•Dark Cinema: For dark movie content.
•Sport: For sport picture.
•User: Memorize user's settings.
Wall color Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Brightness Adjust the brightness of the image.
•Press to darken the image.
•Press to lighten the image.
Contrast "Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
•Press to decrease the contrast.
•Press to increase the contrast.
Saturation Adjusts a video image from black and white to fully saturated
color.
•Press to decrease the amount of color in the image.
•Press to increase the amount of color in the image.
27
English
Note: "Saturation" and "Tint" functions are not supported under computer
or HDMI mode.
Note: Functions vary depending on model definition.
Tint Adjusts the color balance of red and green.
•Press to increase the amount of green in the image.
•Press to increase the amount of red in the image.
Color
Temperature
Mode
Use this function to choose CT1, CT2 (Native), CT3, User mode.
R Gain
Adjusts the red gain for color temperature optimization.
G Gain
Adjusts the green gain for color temperature optimization.
B Gain
Adjusts the blue gain for color temperature optimization.
R Bias
Adjusts the red bias for color temperature optimization.
G Bias
Adjusts the green bias for color temperature optimization.
B Bias
Adjusts the blue bias for color temperature optimization.
Gamma Effects the representation of dark scenery. With greater gamma
value, dark scenery looks brighter.
28
English
Image
Projection
• Front-Desktop: The factory default setting.
• Rear-Desktop: When you select this function, the projector
reverses the image so you can project from behind a translucent
screen.
• Rear-Ceiling: When you select this function, the projector
reverses and inverts the image at same time. You can project from
behind a translucent screen with ceiling mounted projection.
• Front-Ceiling: When you select this function, the projector
inverts the image for ceiling-mounted projection.
Aspect Ratio Use this function to choose your desired aspect ratio.
•Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
•Full: Resize image to fit full screen by width (1280 pixels) and
height (800 pixels).
•4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
•16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
•L.Box: Keep original signal aspect ratio and zoom in by 1.333
times.
H./V. Keystone Auto V. Keystone
Automatically adjusts vertical image.
H. Keystone
Press the or button to adjust image distortion horizontally
and makes a squarer image.
V. Keystone
Press the or button to adjust image distortion vertically and
makes a squarer image.
4 Corner
Correction
Manually adjusts the shape and size of an image that is unevenly
rectangular on all sides. Press "MODE" repeatedly to select the corner
that you wish to adjust. Press four directional selection keys to adjust
the image shape.
<Note> The function is unavailable when H./ V. Keystone is adjusted.
Sharpness Adjusts the sharpness of the image.
•Press to decrease the sharpness.
•Press to increase the sharpness.
29
English
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI or Video mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only
supported under HDMI mode.
Note: Functions vary depending on model definition.
H. Position
(Horizontal
position)
•Press to move the image left.
•Press to move the image right.
V. Position
(Vertical position) •Press to move the image down.
•Press to move the image up.
Frequency "Frequency" changes the projector's refresh rate to match the
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
Tracking Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to
correct it.
HDMI Color Range Adjust the color range of the HDMI image data to correct color display
error.
•Auto: Automatically adjust by information from player.
•
Limited Range: Prosess the input image as limited color range data.
•Full Range: Prosess the input image as full color range data.
HDMI Scan Info Adjust the overscan ratio of the HDMI image on screen.
•Auto: Automatically adjust by information from player.
•Underscan: Always no overscan on HDMI image.
•Overscan: Always keep overscan on HDMI image.
30
English
Setting
Startup Screen Use this function to select your desired startup screen. If you
change the setting, the changes will take effect when you exit the
OSD menu.
• Acer: The default startup screen of your Acer projector.
• User: Use memorize picture from "Screen Capture" function.
Screen Capture Use this function to customize the startup screen. To capture the
image that you want to use as the startup screen, follow the
instructions below.
Notice:
Before proceeding with the following steps, make sure that the
"Keystone" is set to the default value 0 and the aspect ratio is set
to 4:3. For details, refer to the "Image" section.
• Change the "Startup Screen" from the default setting "Acer"
to "User".
• Press "Screen Capture" to customize the startup screen.
• A dialog box appears to confirm the action. Choose "Yes" to
use the current image as your customized startup screen. The
capture range is the red rectangular area. Choose "No" to
cancel the screen capture and exit the onscreen display (OSD).
• A message appears, stating that the screen capture is in
progress.
• When the screen capture is finished, the message disappears
and the original display is shown.
• The customized startup screen, as shown below, takes effect
when there is a new input signal or when you restart the
projector.
Source Lock When Source Lock is turned "Off", the projector will search for
other signals if the current input signal is lost. When Source Lock is
turned "On", it will "lock" the current source channel unless you
press "Source" button on the remote control for the next channel.
Closed Caption Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .
Auto Screen Default is "On", the down/up move of electronic screen will be
related with power on/off of the projector.
VGA OUT (Standby) Default is "Off". Choose "On" to enable VGA OUT connection.
DC 5V Out (Standby) Default is "Off". Choose "On" to enable DV 5V OUT connection
during standby mode.
HDMI CEC Default is "Off". Select “On” to enable HDMI CEC function.
Reset •Press the button and choose "Yes" to return the
parameters on all menus to the factory default settings.
31
English
Security Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first
before changing the security settings.
•Select "On" to enable the security function. The user has to
enter a password to operate the projector. Please refer to the
"User Password" section for details.
•If "Off" is selected, then the user can turn on the projector
without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•Press or to select the timeout interval.
•The range is from 10 minute to 990 minutes.
•When the time is up, the projector will prompt the user to
enter the password again.
•The factory default setting of "Timeout(Min.)" is "Off".
•Once the security function is enabled, the projector will
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
User Password
•Press to setup or change the "User Password".
•Press number keys to set your password on the remote control
and press "MENU" to confirm.
•Press to delete character.
•Enter the password when you see "Confirm Password"
displayed.
•The password should be between 4 and 8 characters long.
•If you select "Request password only when plugging the
power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.
•If you select "Always request password while projector turns
on.", the user has to enter the password every time when the
projector is turned on.
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•Press to change the "Administrator Password".
•The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to
retrieve the administrator password:
•An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.
•If losing this security card and number, please contact with an
Acer service center.
32
English
Note: Functions vary depending on model definition.
Management
Note: Functions vary depending on model definition.
Lock to user startup screen
Default Lock User Startup Screen is "Off". If lock user startup screen
is "On", users cannot change startup screen anymore and avoid
other users change that arbitrarily. Choose "Off" to unlock startup
screen.
LAN LAN
Default is "Off". Choose "On" to enable LAN connection.
<Note> If users want to do LAN control under standby mode,
change VGA OUT (Standby) from Off to On.
LAN IP/Mask
Identify IP and Mask address.
LAN Reset
Reset LAN function.
Control Channel
Default is "RS232/LAN". Choose "HDBaseT" to enable HDBaseT
connection
HDBaseT IR Carrier
Default is "Off", Choose "On" to enable HDBaseT IR Carrier
function.
ECO Mode Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
High Altitude Choose "On" to turn on High Altitude mode. Operate the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.
Turn Off Mode •Instant Off: Shuts down the projector without fan cooling.
•Instant Resume: Resumes the system when the Power button
is pressed again within 2 minutes.
Auto Shutdown The projector will automatically shutdown when there is no signal
input after the allocated time. (default is 120 minutes)
AC Power On Choose "On" to power on projector while AC power plug in.
Lamp Hour Elapse Displays the lamp’s elapsed operating time (in hours).
Lamp Reminding Activate this function to display a reminder to change the lamp 30
hours before its expected end-of-life.
Lamp Hour Reset Press the button and choose "Yes" to turn the lamp hour
counter to 0 hours.
33
English
Audio
Note: Functions vary depending on model definition.
Volume •Press to decrease the volume.
•Press to increase the volume.
MIC Volume Adjust the volume from "MIC IN" connector.
Mute •Choose "On" to mute the volume.
•Choose "Off" to restore the volume.
Power On/Off Volume Select this function to adjust the notification volume when
turning the projector on/off.
Alarm Volume Select the function to adjust the volume of any warning
notifications.
34
English
3D
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,
- Stereoscopic Player (Trial):
http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial):
http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note: "3D L/R Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
Note: WUXGA model 24P 3D cannot be scaling due to TI ASIC buffer memory
limitation, and once detect 24P 3D (96Hz or 144Hz) inputs, Aspect Ratio /
HDMI Scan Info will be gray out, also HIDE will be not supported.
Language
3D Choose "On" to enable DLP 3D function.
•On: Choose this item while using DLP 3D glasses, 120Hz 3D
capable graphics cards and HQFS format file or DVD with
corresponding SW player.
•Off: Turn off 3D mode.
3D Format If the 3D content is not displayed correctly, you can select a 3D
format that suits the 3D content you are viewing and obtain the
best result.
24P 3D Choose "96Hz" or "144Hz" to compatible with 3D glasses.
3D L/R Invert If you see a discrete or overlapping image while wearing DLP 3D
glasses, you may need to execute "Invert" to get best match of
left/right image sequence to get the correct image (for DLP 3D).
3D Warning Message Choose "On" to display the 3D warning message.
Language Choose the multilingual OSD menu. Use the or key
to select your preferred menu language.
•Press to confirm the selection.
35
English
Acer LAN webpage management
How to login in
Open browser and enter the Server IP address by 192.168.100.10 to find below
homepage of acer LAN webpage management. A password is needed to login
in before using.
Select a user. Administrator is with high authority that can process more
operations such as network setting and alert setting. Default password of
administrator is "admin". And User is with normal authority with default
password by "user". Click Login button to enter into homepage with correct
password.
36
English
Home
Home page shows connection status and you can find three main functions
listed, Control Panel, Network Setting and Alert Setting.
Note: Control Panel and Network Setting are only for Administrator
account.
Control Panel
Enduser can control and adjust projector setting value via this page.
37
English
Network Setting
Enduser can set IP address, group name and password as wish. After change
network configurations or password, projector will reboot automatically after
press "Apply".
Note: Group Name and projector Name must be less then 32 characters.
Alert Setting
Enduser can send mail with error message right away if projector has problem.
38
English
Logout
After tap Logout, you will return to login page within 5 seconds.
Note: Functions vary depending on model definition.
39
English
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
# Problem Solution
1 No image appears
onscreen •Connected as described in the "Getting Started"
section.
•Ensure none of the connector pins are bent or
broken.
•Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•Make sure you have removed the lens cap and the
projector is switched on.
2 Partial, scrolling
or incorrectly
displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
Windows 8))
•Press "RESYNC" on the control panel.
•For an incorrectly displayed image:
•Open "My Computer", open the "Control
Panel", and then double-click the "Display"
icon.
•Select the "Settings" tab.
•Verify that your display resolution setting is
lower than or equal to WUXGA-RB (1920 x
1200).
•Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
•Verify that the resolution setting is lower than
or equal to WUXGA-RB (1920 x 1200).
•Click the "Change" button under the
"Monitor" tab.
•Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•Verify that the resolution setting of the
monitor display is lower than or equal to
WUXGA-RB (1920 x 1200).
40
English
3 Partial, scrolling
or incorrectly
displayed image
(For notebooks)
•Press "RESYNC" on the control panel.
•For an incorrectly displayed image:
•Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
4 The screen of the
notebook
computer is not
displaying your
presentation
•If you are using a Microsoft® Windows® based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
•If you are using an Apple® Mac® OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On".
5 Image is unstable
or flickering •Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
•Change the display color depth settings on your
computer.
6 Image has vertical
flickering bar •Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
•Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
7 Image is out of
focus •Make sure the lens cap is removed.
•Adjusts the focus ring on the projector lens.
•Make sure the projection screen is within the
required distance of 3.3 to 28.1 feet (1.0 to 8.6
meters) (XGA series) / 3.3 to 30.7 feet (1.0 to 9.4
meters) (1080p series) / 3.3 to 29.9 feet (1.0 to 9.1
meters) (WUXGA series) from the projector. Refer to
the "How to get a preferred image size by adjusting
distance and zoom" section for more information.
41
English
8 Image is stretched
when displaying a
"widescreen"
DVD title
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
•If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•If you play an Letterbox (LBX) format DVD title,
please change the format to Letterbox (LBX) in the
projector OSD.
9 Image is too small
or too large •Adjust the zoom lever on the top of the projector.
•Move the projector closer to or further from the
screen.
•Press "MENU" on the remote control. Go to "Image -
-> Aspect Ratio" and try different settings or press
"ASPECT RATIO" on the remote control to adjust
directly.
10 Image has slanted
sides •If possible, reposition the projector so that it is
centered on the screen.
•Press the "Keystone / " button on the remote
control until the sides are vertical.
11 Image is reversed •Select "Image --> Projection Mode" on the OSD and
adjust the projection direction.
42
English
OSD Messages
Problems with the Projector
# Condition Message Reminder
1 Message •Fan Fail - the system fan is not working.
•Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed
to cool down before it may be used. Please check the
following message.
Please also check the dust filters if they are installed. If the
dust filter is clogged with dust, please clean it. Please refer to
"Cleaning and replacing the dust filters" for details.
•Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
# Condition Solution
1 The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2 Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
43
English
LED & Alarm Definition Listing
LED Messages
Message
Lamp_LED Temp_LED Power LED
Red Red Red Blue
Input power plug Flash ON to
OFF 100ms
Flash ON to
OFF 100ms
Flash ON to
OFF 100ms
--
Standby -- -- ON --
Power button ON -- -- -- ON
Lamp retry -- -- -- Quick
Flashing
Power off (Cooling state) -- -- Quick
Flashing
--
Power button OFF
(cooling completed;
standby mode)
-- -- ON --
Error (thermal failure) -- ON -- ON
Error (fan lock) -- Quick
Flashing
-- ON
Error (lamp breakdown) ON -- -- ON
Error (color wheel fail) Quick
Flashing
-- -- ON
44
English
How to install cable management
I. Ceiling Mount Scenario
1 Plug in power cord and other cables you need.
2 Install two support base and tighten the screws.(Illustration #1,2,3,4)
3 Push the cable management. (Illustration #5)
4 If you need to install Acer Dongle
(WirlessHD-Kit/WirelessAndroid-Kit/WirelessCAST), follow the below steps:
(A) Use a screwdriver to remove the screw from the cover.
(B) Push up the cover.
(C) Remove the cover.
(D) Connect dongle to HDMI extension cable port; Connect to HDMI port
on projector.
5 Disassembly the cable management cover firmly to projector, and tighten
the screw. (Illustration #5,4,3,2,1)
1
2
3
4
5
a
b
c
1
2d
45
English
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then
unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Pull out the dust filter. (Illustration #1, #2)
4 To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipment. (Illustration #3)
5 If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
MODE
RESYNC
LAMP
TEMP
1
1
3
2
46
English
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1 Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
2 Remove the screw that secure the lamp module. (Illustration #3)
Lift the handle so that it stands up. (Illustration #4)
Pull out the lamp plug. (Illustration #5)
3 Lift the handle so that it stands up. Pull out the lamp module by force.
(Illustration #6)
To replace the lamp module, use a new lamp and reverse the above steps.
1
2
3
5
4
6
47
English
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
48
English
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1 Drill four holes into a solid, structural ceiling member, and secure the
ceiling mount base to the ceiling.
2 Choose the length combination based on actual environment. (CM-01S
doesn’t include Type 2 and Type 3.)
Type 1 Type 2 Type 3
49
English
3 Type 1:
For the standard size use three bracket screws to mount the projector to
the ceiling mount bracket.
Type 2 and Type 3:
Alternatively, for the larger size, use the sliding extensions for more
supports.
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution.
4 Connect the main body connector to the projector bracket (illustration 1),
and then screw up four screws (illustration 2).
Type 1: Type 2: Type 3:
Illustration 1 Illustration 2
50
English
5 Adjust the angle and positioning as necessary.
Screw Type B Washer Type
Diameter (mm) Length (mm) Large Small
425VV
360°
85.00 mm55.00 mm
82.30 mm 104.07 mm
SCREW SPEC. M4 x 25 mm
51
English
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
Projection system DLP®
Resolution •P6200/F211/PM-X01/P6200S/F211S/PM-X01S series:
Native 1024 x 768 XGA resolution
•P6500/P6505/F251/PM-801 series: 1920x1080 1080p
resolution
•P6600/P6605/F261/PM-WU01 series: True 1920x1200
WUXGA resolution
•Maximum: UXGA (1600 x 1200), WSXGA+
(1680x1050), 1080p(1920x1080), WUXGA-RB (1920
x 1200)
Computer compatibility IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +
Video compatibility NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Aspect ratio Full, 4:3, 16:9, L.Box
Displayable colors 1.07 billion colors
Projection lens •P6200/F211/PM-X01/P6200S/F211S/PM-X01S series:
F = 2.5 ~ 2.93, f = 15.98mm ~ 21.42mm,
1:1.36 Manual Zoom and Manual Focus
•P6500/P6505/F251/PM-801/P6600/P6605/F261/PM-
WU01 series:
F = 2.5 ~ 3.26, f = 20.91mm ~ 32.63mm,
1:1.59 Manual Zoom and Manual Focus
Projection screen size (diagonal) •P6200/F211/PM-X01/P6200S/F211S/PM-X01S series:
26" (66cm) ~ 300" (762cm)
•P6500/P6505/F251/PM-801 series:
20" (51cm) ~ 300" (762cm)
•· P6600/P6605/F261/PM-WU01 series:
21" (53cm) ~ 300" (762cm)
Projection distance •P6200/F211/PM-X01/P6200S/F211S/PM-X01S series:
3.3' (1.0m) ~ 28.1' (8.6m)
•P6500/P6505/F251/PM-801 series: 3.3' (1.0m) ~ 30.7'
(9.4m)
•P6600/P6605/F261/PM-WU01 series:
3.3' (1.0m) ~ 29.9' (9.1m)
Throw ratio •P6200/F211/PM-X01/P6200S/F211S/PM-X01S series:
70"@2m (1.40 ~ 1.91:1)
•P6500/P6505/F251/PM-801 series: 64"@2m (1.41 ~
2.24:1)
•P6600/P6605/F261/PM-WU01 series:
66"@2m (1.41 ~ 2.24:1)
Horizontal scan rate 15 - 100 kHz
Vertical refresh scan rate 24 - 120 Hz
52
English
Lamp type •P6200/F211/PM-X01/P6200S/F211S/PM-X01S series:
310 W user-replaceable lamp
•P6500/P6505/F251/PM-801/P6600/P6605/F261/PM-
WU01 series: 365 W user-replaceable lamp
Keystone correction ±30 degrees
Audio Internal speaker with 10 W x 2 output
Weight 4.5 Kg (9.92 lbs)
Dimensions (W x D x H) 373 mm X 223.4 mm X 100.5 mm (14.7" x 8.8" x 4.0")
Digital Zoom 2X
Power supply AC input 100 - 240 V auto-switching power supply
Power consumption Normal mode: 315W ± 10% @ 110VAC
ECO mode: 260W ± 10% @ 110VAC
Standby mode < 0.5W
Operating temperature 0ºC to 40ºC / 32ºF to 104ºF
I/O connectors •Power socket x1
•VGA input x2
•VGA output x1
•Composite input x1
•S-Video input x1
•YPbPr/YCbCr input x1
•HDMI (MHL) x1
•HDMI x1
•RS232 x1
•Mini USB x 1: (for firmware upgrade)
•Audio input x1
•Microphone input x1
•Audio input (RCA) x1
•Audio output x 1
•USB DC 5V out x1
•DC 12V out x 1
•RJ45 LAN input x 1
•HDBaseT input x 1 (only for P6600/P6605/F261/PM-
WU01 series)
Standard package contents •AC power cord x1
•VGA cable x1
•Remote control x1
•Battery x2 (for remote control) (option)
•User's guide (CD-ROM) x1
•Quick start guide x1
•Security card x1
•Cable management cover x1
•Dust filters x1 (option)
•Carrying case x1 (option)
53
English
Note: Design and specifications are subject to change without
notice.
54
English
Compatibility modes
A. VGA Analog
1 VGA Analog - PC Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
VGA 640x480 60 31.5
640x480 72 37.9
640x480 75 37.5
640x480 85 43.3
640x480 120 61.9
SVGA 800x600 56 35.1
800x600 60 37.9
800x600 72 48.1
800x600 75 46.9
800x600 85 53.7
800x600 120 77.4
XGA 1024x768 60 48.4
1024x768 70 56.5
1024x768 75 60.0
1024x768 85 68.7
1024x768 120 99.0
SXGA 1152x864 70 63.8
1152x864 75 67.5
1152x864 85 77.1
1280x1024 60 64.0
1280x1024 72 77.0
1280x1024 75 80.0
1280x1024 85 91.1
QuadVGA 1280x960 60 60.0
1280x960 75 75.2
SXGA+ 1400x1050 60 65.3
UXGA 1600x1200 60 75.0
PowerBook G4 640x480 60 31.4
PowerBook G4 640x480 66.6(67) 34.9
PowerBook G4 800x600 60 37.9
PowerBook G4 1024x768 60 48.4
PowerBook G4 1152x870 75 68.7
PowerBook G4 1280x960 75 75.0
i Mac DV (G3) 1024x768 75 60.0
55
English
2 VGA Analog - Extended Wide timing
3 VGA Analog -Component Signal
B. HDMI Digital
1 HDMI - PC Signal
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.8
1280x768 75 60.3
1280x768 85 68.6
1280x720 60 44.8
1280x720 120 92.9
1280x800 60 49.6
*1920x1200 60 74
1440x900 60 59.9
WSXGA+ 1680x1050 60 65.3
1920x1080
(1080P) 60 67.5
1366x768 60 47.7
WUXGA *1920x1200-RB 59.94 74.04
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
480i 720x480(1440x480) 59.94 (29.97) 15.7
576i 720x576(1440x576) 50(25) 15.6
480p 720x480 59.94 31.5
576p 720x576 50 31.6
720p 1280x720 60 45.0
720p 1280x720 50 37.5
1080i 1920x1080 60(30) 33.8
1080i 1920x1080 50(25) 28.1
1080p 1920x1080 23.97/24 27.0
1080p 1920x1080 60 67.5
1080p 1920x1080 50 56.3
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
VGA 640x480 60 31.5
640x480 72 37.9
640x480 75 37.5
640x480 85 43.3
640x480 120 61.9
56
English
2 HDMI - Extended Wide timing
SVGA 800x600 56 35.1
800x600 60 37.9
800x600 72 48.1
800x600 75 46.9
800x600 85 53.7
800x600 120 77.4
XGA 1024x768 60 48.4
1024x768 70 56.5
1024x768 75 60.0
1024x768 85 68.7
1024x768 120 99.0
SXGA 1152x864 70 63.8
1152x864 75 67.5
1152x864 85 77.1
1280x1024 60 64.0
1280x1024 72 77.0
1280x1024 75 80.0
1280x1024 85 91.1
QuadVGA 1280x960 60 60.0
1280x960 75 75.2
SXGA+ 1400x1050 60 65.3
UXGA 1600x1200 60 75.0
PowerBook G4 640x480 60 31.4
PowerBook G4 640x480 66.6(67) 34.9
PowerBook G4 800x600 60 37.9
PowerBook G4 1024x768 60 48.4
PowerBook G4 1152x870 75 68.7
PowerBook G4 1280x960 75 75.0
i Mac DV (G3) 1024x768 75 60.0
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
WXGA 1280x768 60 47.8
1280x768 75 60.3
1280x768 85 68.6
1280x720 60 44.8
1280x720 120 92.9
1280x800 60 49.6
*1280x800-RB 119.909 101.6
1440x900 60 59.9
*1920x1200 60 74
57
English
3 HDMI - Video Signal
4 HDMI - 1.4a 3D Timing
WSXGA+ 1680x1050 60 65.3
1920x1080
(1080P) 60 67.5
1366x768 60 47.7
WUXGA *1920x1200-RB 59.94 74.04
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
480i 720x480(1440x480) 59.94 (29.97) 15.7
576i 720x576(1440x576) 50(25) 15.6
480p 720x480 59.94 31.5
576p 720x576 50 31.6
720p 1280x720 60 45.0
720p 1280x720 50 37.5
1080i 1920x1080 60(30) 33.8
1080i 1920x1080 50(25) 28.1
1080p 1920x1080 23.97/24 27.0
1080p 1920x1080 60 67.5
1080p 1920x1080 50 56.3
1080p *1920x1200 59.94 74.04
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
720p (Frame Packing) 1280 x 720 50 37.5
720p (Frame Packing) 1280 x 720 60 45.0
1080p (Frame Packing ) 1920 x1080 24 27.0
720p (Frame Packing) 1280 x 720 50 37.5
720p (Frame Packing) 1280 x 720 60 45.0
1080i (Top and Bottom) 1920 x1080 50 (25) 28.1
1080i (Top and Bottom) 1920 x1080 60 (30) 33.8
1080p (Top and Bottom) 1920 x1080 24 27.0
1080p (Top and Bottom) 1920 x1080 50 56.3
1080p (Top and Bottom) 1920 x1080 60 67.5
720p (Side by Side (Half)) 1280 x 720 60 45.0
1080i (Side by Side (Half)) 1920 x1080 50 (25) 28.1
1080i (Side by Side (Half)) 1920 x1080 60 (30) 33.8
1080p (Side by Side (Half)) 1920 x1080 50 56.3
1080p (Side by Side (Half)) 1920 x1080 60 67.5
58
English
C. MHL Digital
Note: * Functions vary depending on model definition.
Graphic source monitor
range limits
Horizontal scan rate: 15k-100kHz
Vertical scan rate: 24-120 Hz
Max. pixel rate: 165 MHz
Modes Resolution V.Frequency
[Hz]
H.Frequency
[KHz]
VGA *640x480 59.94/60 31.5
480i *720x480 (1440x480) 59.94/60 15.7
576i *720x576 (1440x576) 50(25) 15.6
480p *720x480 59.94/60 31.5
480p_2x *1440x480 59.94/60 31.5
576p *720x576 50 31.3
576p_2x *1440x576 50 31.3
720p *1280x720 59.94/60 45.0
720p *1280x720 50 37.5
1080i *1920x1080 60(30) 33.8
1080i *1920x1080 50(25) 28.1
1080p *1920x1080 23.97/24 27.0
1080p *1920x1080 25 28.1
1080p *1920x1080 29.97/30 33.8
Graphic source monitor
range limits
Horizontal scan rate: 15k-50 kHz
Vertical scan rate: 24-60 Hz
Max. pixel rate: Digital: 75 MHz
58
English
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the device and receiver.
•Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
59
English
English
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-247)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
001
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail: ru.jan@acer.com
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
www.acer.it
Declare under our own responsibility that the product:
Product:
DLP Projector
Trade Name:
Acer
Model Number:
DWU1503/D1P1504/DNX1506/DNX1509
P6600/P6605/F261/PM-WU01/P6500/P6505/F251/PM-801/
P6200/F211/PM-X01/P6200S/F211S/PM-X01S
To which this declaration refers conforms to the relevant standard or other standardizing documents:
x EN55022:2010 Class B; EN 55024:2010
x EN61000-3-2:2006+A1:2009+A2:2009, Class A
x EN61000-3-3:2008
x EN 60950-1:2006/A11:2009/A1:2010+A12:2011
x Regulation (EC) No. 1275/ 2008; EN 62301:2005
x EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2015.
_______________________________ Oct., 21, 2015
RU Jan / Sr. Manager Date
Regulation, Acer Inc.
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
P
roduct:
DLP
Projector
Model
Number:
DWU1503/D1P1504/DNX1506/DNX1509
Machine Type:
P66
00/P6605/F261/PM-WU01/P6500/P6505/
F251/
PM
-801/ P6200/F211/PM-X01/P6200S/F211S/
PM
-X01S
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party:
333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Acer Representative
Phone No.:
254-298-4000
Fax No.:
254-298-4147