Acer PO3-600 User Manual

Displayed below is the user manual for PO3-600 by Acer which is a product in the PCs/Workstations category. This manual has pages.

Related Manuals

Acer XB323UGP Manual

Acer CP514-1W Manual

Acer SF314-59-78ME Manual

Acer K243YBMIX Manual

Acer A3-A10 Manual

Acer GN246HL Bbid Manual

Acer P1510 Manual

Acer WirelessCAST (MWA3) Manual

Table of Contents -

Predator PO3-600

User’s Guide

- Upgrading your Computer

Desktop Computer Covers:

Tower models

This revision: April 2018 V1.00

Important

This manual contains proprietary information that is protected by

subject to change without notice. Images provided herein are for

reference only and may contain information or features that do not

apply to your computer. Acer Group shall not be liable for technical

or editorial errors or omissions contained in this manual.

Table of Contents -

Table of Contents

1. UPGRADING YOUR COMPUTER ............... 5

Installation precautions

.............................. 5

ESD precautions

.......................................... 5

Required tools

.............................................. 5

Pre-installation instructions

.................... 6

Post-installation instructions

.................. 6

System Upgrade

........................................... 7

Removing the left side system cover

.... 7

Installing the left side system cover

...... 8

Hard drives

.................................................... 9

Removing the 3.5-inch hard drives

....... 9

Installing the 3.5-inch hard drives

....... 12

Memory

........................................................ 14

Memory configuration guidelines

....... 14

Removing a memory module

................ 15

Installing a memory module

.................. 16

Graphic board

............................................. 17

Removing the Graphic board

................ 17

Installing the Graphic board

.................. 20

M.2 SSD module

......................................... 22

Removing the M.2 SSD module

............ 22

Installing the M.2 SSD module

............. 25

2 PREDATORSENSE .................................. 29

PredatorSense features

............................ 29

- Upgrading your Computer

Upgrading your Computer

In this section, you will find:

• Instructions on how to replace a hardware component

Upgrading your Computer -

1. UPGRADING YOUR COMPUTER

Installation precautions

Before you install any computer component, we recommend

that you read the following sections. These sections contain

important ESD precautions along with pre-installation and

post-installation instructions.

ESD precautions

Electrostatic discharge (ESD) can damage your processor,

disk drives, expansion boards, and other components.

Always observe the following precautions before you install a

computer component:

1. Do not remove a component from its protective

packaging until you are ready to install it.

2. Wear a wrist grounding strap and attach it to a metal

part of the computer before handling components. If a

wrist strap is not available, maintain contact with the

computer throughout any procedure requiring ESD

protection.

Required tools

In performing the component replacement process, you will

need the following tools:

• Philips screwdriver

• Hex screwdriver

• Flat screwdriver

• Scissors

Note

The screws for the different components vary in size. During the

disassembly process, group the screws with their corresponding

components to avoid mismatches when putting back the components.

- Upgrading your Computer

Pre-installation instructions

Always observe the following before you install any

component:

1. Make sure that the ODD and card reader slot is empty.

2. Turn off the power to the computer and all peripherals.

3. Unplug the power cord from the computer.

4. Unplug the network cable and all connected peripheral

devices from the computer.

5. Place the computer on a flat, steady surface.

6. Open your computer according to the instructions on

Removing the rear system cover on page 7 and

Removing the left side system cover on page 9.

7. See the following sections for specific instructions on

the component you wish to install.

Post-installation instructions

Observe the following after installing a computer component:

1. See to it that the components are installed according to

the step-by- step instructions in their respective

sections.

2. Replace any expansion boards or peripherals that you

removed earlier.

3. Replace the system covers. See Installing the left side

system cover on page 10 and Installing the rear

system cover on page 8.

4. Connect the necessary cables.

5. Turn on your computer.

Warning

Not turning off the computer properly before you start installing the

components may cause serious damage. Do not attempt the

procedures described in the following sections unless you are a

qualified service technician.

Upgrading your Computer -

System Upgrade

Removing the left side system cover

1. Before you proceed, make sure that you have turned

off your computer and all peripherals connected to it.

Read the Pre- installation instructions on page 6.

2. Remove the two screws that secure the system cover

to the computer.

3. Slide the cover toward the back of the computer and

pull away from the side of the computer.

4. Set the cover aside for re-installation later.

- Upgrading your Computer

Installing the left side system cover

1. Align the cover to the sides of the computer and slide

the cover toward the front of the computer.

2. Secure the cover with two screws.

3. Observe the Post-installation instructions on page 6.

Upgrading your Computer -

Hard drives

The computer supports installation of one 3.5-inch SATA

hard drives in the internal HDD cage.

Removing the 3.5-inch hard drives

1. Perform Pre-installation instructions on page 6.

2. Remove the four screws that secure the HDD bracket

to the computer.

- Upgrading your Computer

3. Rotating the HDD bracket and pull away from the side

of computer (1) (2).

4. Disconnect the power and data cables from the hard

drives.

Upgrading your Computer -

5. Remove the four screws that secure the hard drives to

the bracket.

- Upgrading your Computer

Installing the 3.5-inch hard drives

1. Remove the new hard drive from their packaging.

2. Insert the new hard drive into the bracket and secure

the new hard drive with four screws.

3. Connect the power and data cables to the hard drive.

Upgrading your Computer -

4. Insert the HDD bracket into the side of computer (1) (2)

and rotating the bracket to fix.

5. Secure the HDD bracket with four screws.

6. Observe the Post-installation instructions on page 6.

- Upgrading your Computer

Memory

The computer has four DDR4 U-DIMM slots that support up

to 64 GB maximum system memory.

Memory configuration guidelines

 To ensure data integrity, use only Acer-approved DDR4 2400 MHz

or DDR4 2666 MHZ type memory modules.

 Memory modules must be installed starting with DIMM3 slot.

 Always handle memory modules by its edges.

 When installing memory modules, populate the DIMM slots

according to the table below.

Size

DIMM1

DIMM2

DIMM3

DIMM4

4GB

N/A

8GB

4GB

N/A

12GB

4GB

N/A

16GB

4GB

8GB

N/A

16GB

8GB

N/A

24GB

8GB

N/A

32GB

8GB

16GB

N/A

32GB

16GB

N/A

48GB

16GB

N/A

64GB

16GB

DIMM4

DIMM3

DIMM2

DIMM1

Upgrading your Computer -

Removing a memory module

1. Perform Pre-installation instructions on page 6.

2. Press outward the holding clips on both sides of the

DIMM slot outward to release the memory module (1).

3. Gently pull the memory module upward to remove it from

the DIMM slot (2).

4. Repeat steps 5~6 to remove the other memory modules.

- Upgrading your Computer

Installing a memory module

1. Select an empty DIMM slot.

2. Remove the new memory module from its packaging,

handling it by the edges.

3. Align then insert the memory module into the DIMM

slot (1).

4. Insert the memory to the slot until the retaining clips

snap inward (2).

The module is keyed so it can only be inserted in one

direction. If the module does not fit, make sure that the

notch in the module lines up with the tab in the

memory slot.

5. Repeat steps 1~4 to install the other memory modules.

6. Observe the Post-installation instructions on page 6.

Note

DIMM slots on the mainboard must be installed only in certain configurations.

Numbers next to DIMM slots correspond to installation sequence.

Be sure to install the memory module in DIMM1 slot followed by DIMM2 slot.

Upgrading your Computer -

Graphic board

The computer contains one or two Graphic boards installed in

the PCIe x16 slots. The detail configuration will be differed by

different models.

Removing the Graphic board

1. Perform Pre-installation instructions on page 6.

2. Remove the 3.5-inch hard drives. See removing the

3.5-inch hard drives.

3. Disconnect the power cables from the Graphic board.

4. Remove the screw that secure the Graphic boards to

the chassis.

- Upgrading your Computer

5. Rotating the latch bracket and graphic board hold

module to release.

6. Release the latch that secures the graphic board to the

mainboard.

Upgrading your Computer -

7. Detach the Graphic board from the PCIe x16 slot.

- Upgrading your Computer

Installing the Graphic board

1. Remove the new graphic board from its packaging.

2. Insert the Graphic boards into the PCIe x16 slot and

push it until it latches into place.

[Note] For replace/upgrade graphic board, please check

the specification of graphic board & power supply first in

order to make sure the graphic board and power supply

could work.

3. Rotating the latch bracket (1) and graphic board hold

module (2) to lock.

Upgrading your Computer -

4. Secure the Graphic board with screws.

5. Connect the power cables to the Graphic boards.

6. Replace the 3.5-inch hard drives. See installing the

3.5-inch hard drives.

7. Observe the Post-installation instructions on page 6.

- Upgrading your Computer

M.2 SSD module

The computer contains one M.2 SSD module installed in the

M.2 PCIe slot.

Removing the M.2 SSD module

1. Perform Pre-installation instructions on page 6.

2. Remove the 3.5-inch hard drives. See removing the

3.5-inch hard drives.

3. Disconnect the power and data cables from the ODD

drives.

4. Press the ODD bracket to down and release it out from

the computer.

Upgrading your Computer -

5. Release front bezel hook and rotating it out from the

computer.

6. Remove the screws and release ODD support out from

computer.

- Upgrading your Computer

7. Remove the screws that secures the M.2 SSD module

from the mainboard.

8. Detach the M.2 SSD module from the mainboard.

Upgrading your Computer -

Installing the M.2 SSD module

1. Remove the new M.2 SSD module from its packaging.

2. Insert the M.2 SSD module into its slot in the

mainboard.

3. Secure the M.2 SSD module and mainboard with

screws.

- Upgrading your Computer

4. Insert the ODD support to the computer and secure the

screws.

5. Align the front bezel hook to the sides of the computer

and rotating it until it into place on the computer.

Upgrading your Computer -

6. Insert the ODD module to the computer and push it

until it latches into place

7. Connect the power and data cables from the ODD

drives.

8. Replace the 3.5-inch hard drives. See installing the

3.5-inch hard drives.

Observe the Post-installation instructions on page 6.

- PredatorSense

PredatorSense

In this section, you will find:

• Introduction to the PredatorSense utility

• How to use PredatorSense

PredatorSense -

2 PREDATORSENSE

PredatorSense (DT) is an Acer proprietary utility to enhance

the user experience of Gaming products on Microsoft

Windows 10.

The central idea of this utility is to provide a user interface to

easily control fan speed and also display system information.

PredatorSense features

•

System information dashboard

•

Fan speed control

•

Monitoring

•

Advanced settings

•

Live update

To set up the PredatorSense application (Windows 10):

1. From the Start menu, select

All apps

2. Select

Acer

3. Select

PredatorSense

[Note] PredatorSense function is keeping increased to enlarge

user experience, Any new features update excluded from user

guide should be possible.

- PredatorSense