Acer PO5-625s User Manual
Displayed below is the user manual for PO5-625s by Acer which is a product in the PCs/Workstations category. This manual has pages.
Related Manuals
Table of Contents -
1
Predator PO5-625s
User’s Guide
-
2
© 2021. All Rights Reserved.
Desktop Computer Covers:
Tower models
This revision: Mar. 2021 V1.00
Important
This manual contains proprietary information that is protected by
copyright laws. The information contained in this manual is
subject to change without notice. Images provided herein are for
reference only and may contain information or features that do not
apply to your computer. Acer Group shall not be liable for technical
or editorial errors or omissions contained in this manual.
The terms HDMI and HDMI High-Definition Multimedia
Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing Administrator,
Inc. in the United States and other countries.
Table of Contents -
3
Table of Contents
1. UPGRADING YOUR COMPUTER .................... 5
Installation precautions
.............................. 5
ESD precautions
.......................................... 5
Required tools
.............................................. 5
Pre-installation instructions
.................... 6
Post-installation instructions
.................. 6
System Upgrade
........................................... 7
Removing the left side system cover
.... 7
Installing the left side system cover
...... 8
Removing the right side system cover
. 9
Installing the right side system cover
. 10
System Layout
............................................. 11
Hard drives
.................................................. 12
Removing the 3.5-inch hard drives
..... 12
Installing the 3.5-inch hard drives
....... 16
Memory
........................................................ 19
Memory configuration guidelines
....... 19
Removing a memory module
................ 20
Installing a memory module
.................. 21
Graphic board
............................................. 22
Removing the Graphic board
................ 22
Installing the Graphic board
.................. 24
M.2 SSD module
......................................... 26
Removing the M.2 SSD module for
M2_1
............................................................ 26
Installing the M.2 SSD module for
M2_1
............................................................ 28
Removing the M.2 SSD module for
M2_2
............................................................ 29
Installing the M.2 SSD module for
M2_2
............................................................ 30
ODD drives
................................................... 31
Open ODD door.
....................................... 31
Easy swap HDD
........................................... 32
Glass Side cover
.......................................... 34
Dust filter
..................................................... 36
ME Features
................................................ 38
2 PredatorSYNC .............................................. 40
PredatorSYNC
............................................. 40
- Upgrading your Computer
4
Upgrading your Computer
In this section, you will find:
• Instructions on how to replace a hardware component
Upgrading your Computer -
5
1. UPGRADING YOUR COMPUTER
Installation precautions
Before you install any computer component, we recommend
that you read the following sections. These sections contain
important ESD precautions along with pre-installation and
post-installation instructions.
ESD precautions
Electrostatic discharge (ESD) can damage your processor,
disk drives, expansion boards, and other components.
Always observe the following precautions before you install a
computer component:
1. Do not remove a component from its protective
packaging until you are ready to install it.
2. Wear a wrist grounding strap and attach it to a metal part
of the computer before handling components. If a wrist
strap is not available, maintain contact with the computer
throughout any procedure requiring ESD protection.
Required tools
In performing the component replacement process, you will
need the following tools:
• Philips screwdriver
• Hex screwdriver
• Flat screwdriver
• Scissors
Note
The screws for the different components vary in size. During the
disassembly process, group the screws with their corresponding
components to avoid mismatches when putting back the components.
- Upgrading your Computer
6
Pre-installation instructions
Always observe the following before you install any
component:
1. Make sure that the ODD and card reader slot is empty.
2. Turn off the power to the computer and all peripherals.
3. Unplug the power cord from the computer.
4. Unplug the network cable and all connected peripheral
devices from the computer.
5. Place the computer on a flat, steady surface.
6. Open your computer according to the instructions on
removing the left side system cover on page 7 and
removing the right side system cover on page 9.
7. See the following sections for specific instructions on the
component you wish to install.
Post-installation instructions
Observe the following after installing a computer component:
1. See to it that the components are installed according to
the step-by- step instructions in their respective sections.
2. Replace any expansion boards or peripherals that you
removed earlier.
3. Replace the system covers. See Installing the left side
system cover on page 8 and installing the right side
system cover on page 10.
4. Connect the necessary cables.
5.
Turn on your computer.
Warning
Not turning off the computer properly before you start installing the
components may cause serious damage. Do not attempt the
procedures described in the following sections unless you are a
qualified service technician.
WARNING: Hot surface. Do not touch.
Upgrading your Computer -
7
System Upgrade
Removing the left side system cover
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre- installation instructions on page 6.
2. Remove the two screws that secure the system cover to
the computer.
3. Slide the cover toward the back of the computer and pull
away from the side of the computer.
4. Set the cover aside for re-installation later.
- Upgrading your Computer
8
Installing the left side system cover
1. Align the cover to the sides of the computer and slide
the cover toward the front of the computer.
2. Secure the cover with two screws.
3. Observe the Post-installation instructions on page 6.
Upgrading your Computer -
9
Removing the right side system cover
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre- installation instructions on page 6.
2. Remove the two screws that secure the system cover to
the computer.
3. Slide the cover toward the back of the computer and pull
away from the side of the computer.
4. Set the cover aside for re-installation later.
- Upgrading your Computer
10
Installing the right side system cover
1. Align the cover to the sides of the computer and slide the
cover toward the front of the computer.
2. Secure the cover with two screws.
3. Observe the Post-installation instructions on page 6.
Upgrading your Computer -
11
System Layout
CPU
RAM
SSD
M2_1
VGA
ODD
SSD
M2_2
HDD
PSU
Wifi
M2_3
- Upgrading your Computer
12
Hard drives
The computer supports installation of one 3.5-inch SATA
hard drives in the internal HDD cage.
Removing the 3.5-inch hard drives
1. Perform Pre-installation instructions on page 6.
2. Remove the two screws that the Mask cover.
3. Take off the Mask Cover.
Upgrading your Computer -
13
4. Remove the four screws that the Power Cover.
5. Take out these Cables
6. Take off the Power Cover.
- Upgrading your Computer
14
7. Disconnect the power and data cables from the hard
drives.
8. Pull black rack out from HDD cage and take it off.
Upgrading your Computer -
15
9. Remove HDD from black rack.
- Upgrading your Computer
16
Installing the 3.5-inch hard drives
1. Remove the new hard drive from their packaging.
2. Insert the new hard drive into the black rack.
3. Insert black rack into HDD cage.
Upgrading your Computer -
17
4. Connect the power and data cables to the hard drive.
5. Insert the Power Cover and fix it.
- Upgrading your Computer
18
6. Insert the Mask Cover and fix it.
7. Observe the Post-installation instructions on page 6
Upgrading your Computer -
19
Memory
The computer has four DDR4 U-DIMM slots that support up
to 64 GB maximum system memory.
Memory configuration guidelines
To ensure data integrity, use only Acer-approved DDR4 2666 MHz
or DDR4 3200 MHz type memory modules.
Memory modules must be installed starting with DIMM1 slot.
Always handle memory modules by its edges.
When installing memory modules, populate the DIMM slots
according to the table below.
DDR4_A1
DDR4_A2
DDR4_B1
DDR4_B2
- Upgrading your Computer
20
Removing a memory module
1. Perform Pre-installation instructions on page 6.
2. Disconnect the thermal fan cable from the mainboard.
3. Press outward the holding clips on both sides of the
DIMM slot outward to release the memory module (1).
4. Gently pull the memory module upward to remove it
from the DIMM slot (2).
5. Repeat steps 3~4 to remove the other memory modules.
2
1
Upgrading your Computer -
21
Installing a memory module
1. Select an empty DIMM slot.
2. Remove the new memory module from its packaging,
handling it by the edges.
3. Align then insert the memory module into the DIMM slot
(1).
4. Insert the memory to the slot until the retaining clips snap
inward (2).
The module is keyed so it can only be inserted in one
direction. If the module does not fit, make sure that the
notch in the module lines up with the tab in the memory
slot.
5. Repeat steps 1~4 to install the other memory modules.
6. Observe the Post-installation instructions on page 6.
Note
DIMM slots on the mainboard must be installed only in certain configurations.
Numbers next to DIMM slots correspond to installation sequence.
Be sure to install the memory module in DIMM1 slot followed by DIMM2 slot.
2
1
- Upgrading your Computer
22
Graphic board
The computer contains one or two Graphic boards installed in
the PCIe x16 slots. The detail configuration will be differed by
different models.
Removing the Graphic board
1. Perform Pre-installation instructions on page 6.
2. Disconnect the power cables from the Graphic board.
3. Remove the screw that secure the Graphic boards to the
chassis.
Upgrading your Computer -
23
4. Release the latch that secures the graphic board to the
mainboard.
5. Detach the Graphic board from the PCIe x16 slot.
6. Remove the screw that secure the Graphic boards to the
VGA Holder Bracket.
- Upgrading your Computer
24
Installing the Graphic board
1. Remove the new graphic board from its packaging.
2. Fix Graphic boards on VGA Holder Bracket with three
screw
3. Insert the Graphic boards into the PCIe x16 slot and
press it down until it latches into place.
[Note] For replace/upgrade graphic board, please check the
specification of graphic board & power supply first in order
to make sure the graphic board and power supply could
work.
Upgrading your Computer -
25
4. Secure the Graphic board with screws.
5. Connect the power cables to the Graphic boards.
6. Observe the Post-installation instructions on page 6
- Upgrading your Computer
26
M.2 SSD module
The computer contains one M.2 SSD module installed in the
M.2 PCIe slot.
Removing the M.2 SSD module for M2_1
1. Perform Pre-installation instructions on page 6.
2. Remove the Graphic board. See Removing the Graphic
board.
3. Remove the screws that secures the M.2 SSD module
from the mainboard.
4. Take off the SSD Plate w/ Pad.
Upgrading your Computer -
27
5. Detach the M.2 SSD module from the mainboard.
- Upgrading your Computer
28
Installing the M.2 SSD module for M2_1
1. Remove the new M.2 SSD module from its packaging.
2. Insert the M.2 SSD module into its slot in the mainboard.
3. Secure the M.2 SSD module and mainboard with screws.
4. Replace the Graphic board. See Installing the Graphic
board.
5. Observe the Post-installation instructions on page 6.
Upgrading your Computer -
29
Removing the M.2 SSD module for M2_2
1. Perform Pre-installation instructions on page 6.
2. Remove the Graphic board. See Removing the Graphic
board.
3. Remove the screws that secures the M.2 SSD module
from the mainboard.
4. Detach the M.2 SSD module from the mainboard.
- Upgrading your Computer
30
Installing the M.2 SSD module for M2_2
1. Remove the new M.2 SSD module from its packaging.
2. Insert the M.2 SSD module into its slot in the mainboard.
3. Secure the M.2 SSD module and mainboard with screws.
4. Replace the Graphic board. See Installing the Graphic
board.
5. Observe the Post-installation instructions on page 6.
Upgrading your Computer -
31
ODD drives
The computer supports installation of one ODD drives.
Open ODD door.
1. Perform Pre-installation instructions on page 6.
2. Push triangle icon for opening.
3. Press ODD eject-Button.
- Upgrading your Computer
32
Easy swap HDD
The computer supports installation of one 2.5-inch SATA
hard drives in the easy swap HDD cage.
1. Perform Pre-installation instructions on page 6.
2. Push triangle icon for opening.
3. Release the latch and take it off.
Upgrading your Computer -
33
4. Insert the new 2.5-inch SATA hard drive into the easy
swap cage.
5. Insert easy swap into HDD cage.
- Upgrading your Computer
34
Glass Side cover
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre-installation instructions on page 6.
2. Remove the two screws that secure the system cover
and take it off.
3. Tack out the glass cover from their packaging.
Upgrading your Computer -
35
4. Secure the glass cover with screws.
5. Observe the Post-installation instructions on page 6
- Upgrading your Computer
36
Dust filter
1. Before you proceed, make sure that you have turned off
your computer and all peripherals connected to it. Read
the Pre- installation instructions on page 6.
2. Pull latch from Dust filter and take it off.
Upgrading your Computer -
37
- Upgrading your Computer
38
ME Features
Headphone hook
Handle
PredatorSYNC -
39
PredatorSYNC
In this section, you will find:
• PredatorSYNC
- PredatorSYNC
40
2 PredatorSYNC
PredatorSYNC
Now you can adjust the RGB LED color through the PredatorSYNC.
Sync RGB LED effects for all LED regions of the motherboard