Bouncepad FLX-W-CA-W-4 User Manual
Displayed below is the user manual for FLX-W-CA-W-4 by Bouncepad which is a product in the Tablet Security Enclosures category. This manual has pages.
Related Manuals
![](/manual/81/211/bg1.webp)
Assembly Instructions
Flex
VESA
Flip
Lounge
1.
![](/manual/81/211/bg2.webp)
Contents
VESA
p.38-48
Flip
p.3-18 p.49-58
Lounge
Flex
p.19-37
2.
![](/manual/81/211/bg3.webp)
Assembly Instructions
VESA
3.
![](/manual/81/211/bg4.webp)
What's in the Box
Case Washer x1 T20 Driver Bit x1
M4 Split Washer x4 M4 20mm Buttonhead Screw x4
no.8 x 38mm Countersunk Screw x4
VESA Mount
4.
![](/manual/81/211/bg5.webp)
What's in the Box
Tablet Support x4
Keys x2
Case x1
Faceplate x1
Corner Pieces x4
Cable Clip x1
Sticker x1
Tablet Setup Kit
This Tablet
Configured for
Attach case to mounting arm with hand operated
screwdriver only.
If you would like to use a different tablet in this case,
please contact us for a conversion kit.
www.bouncepad.com
5.
![](/manual/81/211/bg6.webp)
Pencil
Socket Screwdriver
16mm or 41/64" Drill Bit
2mm or 5/64" Drill Bit
Hand Drill
Tools for the Job
6.
![](/manual/81/211/bg7.webp)
Don't install directly
beneath a light source
Avoid Glare
155cm / 5'
Recommended Installation Height
7.
![](/manual/81/211/bg8.webp)
VESA Mount
Mark all four outer holes
and the large central hole
Pencil
IMPORTANT:
Make sure the Lock will
still be accessible once
the case is installed
Mark the Drill Holes
8.
![](/manual/81/211/bg9.webp)
Through Surface
-Hidden Cabling
-Requires access to back
of the Wall
On Surface
-Visible Cabling
-Perfect for Solid Walls
Choose Cable Routing Method
9.
![](/manual/81/211/bga.webp)
Drill the Holes
16mm
41/64"
2mm
5/64"
2mm
5/64"
2mm
5/64"
NOTE:
The 16mm / 41/64" hole
is only required for 'On
Surface' Mounting
Scale 1:1
IMPORTANT:
2mm / 5/64" holes are
designed for supplied
woodscrews. If using
your own screws eg
when attaching to brick
a different hole size may
be needed
2mm
5/64"
10.
![](/manual/81/211/bgb.webp)
IMPORTANT:
If you have chosen 'On
Surface' cable routing,
the cable must be routed
through cable channel
before screwing to
surface
No.8 38mm Countersunk Screws
VESA Mount
'On Surface' Cable Channel
Attach to Surface
10. 11.
![](/manual/81/211/bgc.webp)
Attach Case
M4 20mm Buttonhead Screws
Case Washer
M4 Split Washers
12.
![](/manual/81/211/bgd.webp)
Route Cable
Cable Clip
Use the adhesive cable
clip to secure cable in
the nearest quadrant to
the Tablet Power Port
13.
![](/manual/81/211/bge.webp)
Case Setup
Cornerpieces
Tablet Supports
Sticker
14.
![](/manual/81/211/bgf.webp)
Insert Tablet
NOTE:
Ensure Tablet is connected
to Power Cable
15.
![](/manual/81/211/bg10.webp)
Lock Up
Turn Key to Lock
1.
Faceplate
Case
2.
3. 16.
![](/manual/81/211/bg11.webp)
VESA Compatibility
The Bouncepad VESA mount can
also be screwed to VESA arms
(fixings not supplied)
17.
![](/manual/81/211/bg12.webp)
Your Bouncepad is now installed
For further information and
support please contact us:
UK & International
+44 (0) 020 3693 0000
hello@bouncepad.com
www.bouncepad.com
Deutschland
+49 (0) 30 6098 5170
hallo@bouncepad.com
www.bouncepad.com/de
USA & Canada
1-617-804-0110
hi@bouncepad.com
www.bouncepad.com/us
18.
![](/manual/81/211/bg13.webp)
Assembly Instructions
Flex
19.
![](/manual/81/211/bg14.webp)
What's in the Box
Surface Mounting
Plate x1
Surface Mounting Plate
Cover x1
Case Washer x1 Through Mounting
Washer x1
T20 Driver Bit x1
M4 Wingnut x4
M4 Split Washer x8
M4 10mm Countersunk Screw x4 M4 Hex Nut x4
M4 16mm Buttonhead Screw x4
M4 40mm Socket Setscrew x4
No.8 38mm Countersunk Screw x4
Flex Stalk 20.
![](/manual/81/211/bg15.webp)
What's in the Box
Tablet Support x4
Keys x2
Case x1
Faceplate x1
Corner Pieces x4
Cable Clip x1
Sticker x1
Tablet Setup Kit
This Tablet
Configured for
Attach case to mounting arm with hand operated
screwdriver only.
If you would like to use a different tablet in this case,
please contact us for a conversion kit.
www.bouncepad.com
21.
![](/manual/81/211/bg16.webp)
Tools for the Job
Pencil
Socket Screwdriver 7mm Spanner or 9/32" Wrench
16mm or 41/64" Drill Bit
5mm or 13/64" Drill Bit 2mm or 5/64" Drill Bit
Hand Drill
22.
![](/manual/81/211/bg17.webp)
Recommended Installation Height
Don't install directly
beneath a light source
Avoid Glare
No Wallmount
90cm / 35''
23.
![](/manual/81/211/bg18.webp)
up to 25mm / 1"
-Seemless appearance
-Requires access beneath mounting
surface
-Option to route cable along surface
when there is no access beneath
mounting surface
Continue to p.25
Through Mount Surface Mount
Choose Mounting Options
Continue to p.28
Any thickness above 25mm / 1"
24.
![](/manual/81/211/bg19.webp)
Through Mount
16mm
41/64"
5mm
13/64"
5mm
13/64"
5mm
13/64"
5mm
13/64"
Drill the Holes
Through Mounting
Washer
Pencil
Front
Mark the Drill Holes
Step 1 of 4 Step 2 of 4
Scale 1:1
This diagram can be
used as a drill template
25.
![](/manual/81/211/bg1a.webp)
M4 40mm Socket Setscrew
Screw in socket setscrews by hand
Step 3 of 4
Through Mount
26.
![](/manual/81/211/bg1b.webp)
Through Mount
7mm Spanner /
9/32" Wrench
Through Mounting Washer
M4 Split Washer x4
M4 Hex Nut/Wingnut x4
Wingnuts
Quick Assembly High Security
Hex Nuts
Now Skip to p.31
Fasten from beneath surface
Step 4 of 4
27.
![](/manual/81/211/bg1c.webp)
Surface Mount
Surface
Mounting Plate
Pencil
Front
Step 1 of 4
Mark the Drill Holes
28.
![](/manual/81/211/bg1d.webp)
Surface Mount
IMPORTANT:
2mm / 5/64" holes are
designed for supplied
woodscrews. If using
your own screws eg
when attaching to brick
a different hole size may
be needed
NOTE:
The 16mm / 41/64" hole is
not required if attaching
to surface with no access
beneath as the power
cable can be routed
along the surface
Drill the Holes
Step 2 of 4
16mm
41/64"
2mm
5/64"
2mm
5/64"
2mm
5/64"
2mm
5/64"
Scale 1:1
This diagram can be
used as a drill template
29.
![](/manual/81/211/bg1e.webp)
Surface Mount
Attach mount plate
1. Screw Mount plate onto Stalk
2. OPTIONAL Route power cable down
the Stalk and through cable channel (only
applicable if you choose to route cable
along surface)
Sticky
Tabs
Cable
Channel
M4 10mm Countersunk Screws
Step 3 of 4
Surface Mounting Plate
Surface Mounting
Plate Cover
30.
![](/manual/81/211/bg1f.webp)
Surface Mount
Attach to Surface
1. Screw Mounting Plate to surface
2. Remove backing from sticky Tabs
3. Slide Surface Mounting Plate Cover
onto Stalk
4. Push down firmly on Mounting Plate
Cover
No.8 38mm Countersunk Screws
Step 4 of 4
Surface Mounting Plate
Surface Mounting Plate Cover
31.
![](/manual/81/211/bg20.webp)
M4 16mm Buttonhead Screws
Case Washer
M4 Split Washers
Attach Case
32.
![](/manual/81/211/bg21.webp)
Route Cable
Cable Clip
Use the adhesive cable
clip to secure cable in
the nearest quadrant to
the Tablet Power Port
33.
![](/manual/81/211/bg22.webp)
Case Setup Cornerpieces
Tablet Supports
Sticker
34.
![](/manual/81/211/bg23.webp)
Insert Tablet
NOTE:
Ensure Tablet is connected
to Power Cable
35.
![](/manual/81/211/bg24.webp)
Lock Up
Turn Key to Lock
1.
Faceplate
Case
2.
3. 36.
![](/manual/81/211/bg25.webp)
Your Bouncepad is now installed
For further information and
support please contact us:
UK & International
+44 (0) 020 3693 0000
hello@bouncepad.com
www.bouncepad.com
Deutschland
+49 (0) 30 6098 5170
hallo@bouncepad.com
www.bouncepad.com/de
USA & Canada
1-617-804-0110
hi@bouncepad.com
www.bouncepad.com/us
37.
![](/manual/81/211/bg26.webp)
Assembly Instructions
Flip
38.
![](/manual/81/211/bg27.webp)
Tools for the Job
Case Washer x1
T20 Driver Bit x1Flip Base Key M4 20mm Buttonhead Screw x4
What’s in the Box
Flip Base x1
Flip Endplates x2
Socket Screwdriver
M4 Split Washer x4
39.
![](/manual/81/211/bg28.webp)
What's in the Box
Tablet Support x4
Keys x2
Case x1
Faceplate x1
Corner Pieces x4
Cable Clip x1
Sticker x1
Tablet Setup Kit
This Tablet
Configured for
Attach case to mounting arm with hand operated
screwdriver only.
If you would like to use a different tablet in this case,
please contact us for a conversion kit.
www.bouncepad.com
40.
![](/manual/81/211/bg29.webp)
Cable Clip
Flip Base
Case
Cable Clip
Use the adhesive cable
clip to secure cable in
the nearest quadrant to
the Tablet Power Port
M4 20mm Buttonhead Screws
M4 Split Washer
Case Washer
Attach Case
41.
![](/manual/81/211/bg2a.webp)
Case Setup
Corner Pieces
Tablet Supports
Sticker
Route Cabling
42.
![](/manual/81/211/bg2b.webp)
Insert Tablet
NOTE:
Ensure Tablet is connected
to Power Cable
43.
![](/manual/81/211/bg2c.webp)
Lock Up
Turn Key to Lock
Faceplate
Case 1.
2.
3. 44.
![](/manual/81/211/bg2d.webp)
Power
NOTE:
Ensure cabling exits
correctly through cable
notch in the Endplate
Connect cable to
power supply
Use the Flip
enclosure to hold a
portable battery
Fit Endplates
OR
45.
![](/manual/81/211/bg2e.webp)
Removing Endplates
If the endplates need to
be removed, insert the
Flip Base Key into the
cable notch and pull
46.
![](/manual/81/211/bg2f.webp)
Surface Mount
The Flip can be surface
mounted using the four
M6 holes found on
the Base
NOTE:
Fixings are not
supplied for surface
mounting the Flip
47.
![](/manual/81/211/bg30.webp)
Your Bouncepad is now installed
For further information and
support please contact us:
UK & International
+44 (0) 020 3693 0000
hello@bouncepad.com
www.bouncepad.com
Deutschland
+49 (0) 30 6098 5170
hallo@bouncepad.com
www.bouncepad.com/de
USA & Canada
1-617-804-0110
hi@bouncepad.com
www.bouncepad.com/us
48.
![](/manual/81/211/bg31.webp)
Assembly Instructions
Lounge
49.
![](/manual/81/211/bg32.webp)
Tools for the Job
Case Washer x1
T20 Driver Bit x1 M4 20mm Buttonhead Screw x2
What’s in the Box
Lounge Cone Assembly x 1
Socket Screwdriver
M4 Split Washer x2
50.
![](/manual/81/211/bg33.webp)
What's in the Box
Tablet Support x4
Keys x2
Case x1
Faceplate x1
Corner Pieces x4
Cable Clip x1
Sticker x1
Tablet Setup Kit
This Tablet
Configured for
Attach case to mounting arm with hand operated
screwdriver only.
If you would like to use a different tablet in this case,
please contact us for a conversion kit.
www.bouncepad.com
51.
![](/manual/81/211/bg34.webp)
Attach Case
M4 Split Washers
M4 20mm
Buttonhead Screws
Security Connector
Case Washer
NOTE:
Lounge Cone is orientated
with the cable pointing up
Ensure Security Connector
is Screwed into Case
52.
![](/manual/81/211/bg35.webp)
Cable Clip
Cable Clip
Use the adhesive cable
clip to secure cable in
the nearest quadrant to
the Tablet Power Port
53.
![](/manual/81/211/bg36.webp)
Corner Pieces
Tablet Supports
Sticker
Case Setup
54.
![](/manual/81/211/bg37.webp)
Insert Tablet
NOTE:
Ensure Tablet is connected
to Power Cable
55.
![](/manual/81/211/bg38.webp)
Lock Up
Turn Key to Lock
Faceplate
Case
1.
2.
3. 56.
![](/manual/81/211/bg39.webp)
Tethering
NOTE:
The tethering loop can be
used with a padlock to
secure your bouncepad to
the furniture
57.
![](/manual/81/211/bg3a.webp)
Your Bouncepad is now installed
For further information and
support please contact us:
UK & International
+44 (0) 020 3693 0000
hello@bouncepad.com
www.bouncepad.com
Deutschland
+49 (0) 30 6098 5170
hallo@bouncepad.com
www.bouncepad.com/de
USA & Canada
1-617-804-0110
hi@bouncepad.com
www.bouncepad.com/us
58.
![](/manual/81/211/bg3b.webp)
![](/manual/81/211/bg3c.webp)
Contact Details
UK & International
+44 (0) 020 3693 0000
hello@bouncepad.com
www.bouncepad.com
Deutschland
+49 (0) 30 6098 5170
hallo@bouncepad.com
www.bouncepad.com/de
USA & Canada
1-617-804-0110
hi@bouncepad.com
www.bouncepad.com/us