Bouncepad Swivel 60 User Manual
Displayed below is the user manual for Swivel 60 by Bouncepad which is a product in the Tablet Security Enclosures category. This manual has pages.
Related Manuals
1
Fixings Kit Tablet Set-up Kit
Sheet Code: BP-OR-IM-041_REV1
Release Date: 30/09/2019
Copyright 2016 Spotspot Ltd. (T/A
Bouncepad) all rights reserved.
Condential, no part of this publication
may be reproduced or transmitted in any
form without the written permission of the
copyright holder.
Swivel 60
Assembly Instructions
Tools Required:
Pencil
Electric Drill
Socket Driver
16mm
Holesaw
*if routing the tablet
cable through your
mounting surface
7mm Spanner *or adjustable spanner
2.5mm Drillbit *if xing from above
5.0mm Drillbit *if xing from below
Faceplate
Case
Rotate
Static60 Mounting Arm
Pair of Keys
In the Box Fixings List
* Due to the modular nature of our product range
you may receive additional xings in the xings kit
4x M4x40mm
Socketset
screw
4x M4x20mm
Buttonhead
screw
4x M4x16mm
buttonhead
screw
4x M4 Split
washer
4x M4
Locking
nut
2x Limit
screw
1x Case
washer
4x M4
Wing nut
4x M4
Washer
4x No.8
Countersunk,
self tapping
Screw
Follow steps B if “Fixing
from below”.
B
Follow steps A if “Fixing
from above”.
A
25mm
Metric Imperial
1"
Maximum Mounting
surface thickness :
34mm
Metric Imperial
1 5/16"
Minimum Mounting
surface thickness :
Congure the rotation range - both
arrows must be pointing in the same
direction. Default conguration is
270˚. Insert 2x limit screws.
180˚ limit screw
position
180˚ limit screw
position
90˚ limit screw
position
90˚ limit screw
position
Tighten screw(s) using hand
tools, using electric tools may
damage your Bouncepad.
Limit Screw
Slotted
Driverbit
Attach the mounting arm. The
mounting arm must forward lean in
the same direction as the two arrows.
2
Tighten screw(s) using hand
tools, using electric tools may
damage your Bouncepad.
T20 Pin Torx
Driverbit
M4x16mm
Buttonhead
screw
Using the hole template (see step A
or B), mark the hole positions specic
to your chosen xing method.
3
A1 B1
Mark ‘A’ positions for “Fixing from above”
(Ø2.5mm drillbit). Mark ‘C’ for the cable hole.
(Ø20.0mm Holesaw).
Mark ‘B’ positions for “Fixing from above”
(Ø5.0mm drillbit). Mark ‘C’ for routing the cable
hole. (Ø20.0mm Holesaw).
Front
C
A
A
A
A
Ø65.5mm
46.0mm
Front
C
B
B
B
B
48.0mm
Drill the
required
holes.
4
T20 Pin Torx
Driverbit
M4x20mm
Buttonhead
screw
M4 Split
Washer
Case Washer
Screw in the 4x Socket
Set Screws. Ensure full
thread engagment.
B2 B3 Secure to the surface.
Locking nuts oer
greater security.
A2 Lift & hold the
rubber screw
covers. A3 Secure the Rotate to
the mounting surface,
then close the covers.
Go to
step 5
A4
T20 Pin Torx
Driverbit
No.8 Countersunk,
self tapping Screw
M4x40mm
Socketset screw
Tighten screw(s) using hand
tools, using electric tools may
damage your Bouncepad.
Tighten screw(s) using hand
tools, using electric tools may
damage your Bouncepad. M4 Wing nut
M4 Washer
M4 Washer
M4 Locking nut
Go to
step 5
B4 5Install your Case as shown. 7Install the Tablet Setup Kit. Each
kit is specic per tablet device and
Bouncepad Case.
Unlock & remove the
Faceplate from the
Bouncepad Case.
6
Tighten screw(s) using hand
tools, using electric tools may
damage your Bouncepad.
4x Tablet Supports 1x Cable Clip 4x Corner Pieces
9Place the tablet into the
Case and connect to
power. 10 Locate and lock the
Faceplate to the Case. 11 Installation is now
complete.
Feed the tablet cable
through the Case and
mounting surface.
8
*We recommend recording the key number so
you can purchase additional keys in the future.
Key number here