D-Link EXO AC2600 MU-MIMO User Manual
Displayed below is the user manual for EXO AC2600 MU-MIMO by D-Link which is a product in the Wireless Routers category. This manual has pages.
Related Manuals
Version 1.00 | July 7, 2017
User Manual
DIR-882-US
AC2600 MU-MIMO Wi-Fi Router
iD-Link DIR-882 User Manual
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any
person or organization of such revisions or changes.
Manual Revisions
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link. All other third-party marks mentioned herein
may be trademarks of their respective owners. This publication may not be reproduced, in whole or in part, without prior
express written permission from D-Link Systems, Inc.
© 2017 D-Link Corporation. All Rights Reserved.
Revision Date Description
1.00 July 7, 2017 • Initial release for revision A1
Preface
iiD-Link DIR-882 User Manual
Table of Contents
Preface ................................................................................. i
Manual Revisions ........................................................................... i
Trademarks ...................................................................................... i
Product Overview .............................................................. 1
Package Contents ......................................................................... 1
Minimum Requirements ............................................................ 2
Introduction ................................................................................... 3
Hardware Overview ..................................................................... 4
Back............................................................................................ 4
LED ............................................................................................. 5
Installation ......................................................................... 6
Before you Begin ........................................................................... 6
Wireless Installation Considerations ......................................7
Manual Setup ................................................................................. 8
Conguration ...................................................................11
Setup Wizard ................................................................................12
QRS Mobile App ..........................................................................17
Web-based Conguration Utility ..........................................21
Home ....................................................................................... 22
Internet ..............................................................................22
DIR-882 ..............................................................................23
Connected Clients .........................................................24
USB Device .......................................................................25
Settings ..................................................................................26
Wizard ................................................................................26
Internet ..............................................................................26
Dynamic IP (DCHP) ..................................................27
Static IP ........................................................................28
PPPoE............................................................................29
PPTP ..............................................................................30
L2TP ..............................................................................32
DS-Lite .......................................................................... 34
IPv6 ................................................................................35
Auto Detection .........................................................36
Static IPv6 ...................................................................37
Auto Conguration .................................................39
PPPoE............................................................................40
IPv6 in IPv4 Tunnel ...................................................42
6 to 4 .............................................................................44
6rd .................................................................................45
Local Connectivity Only ......................................... 47
Triple-Play VLAN .......................................................48
Wireless..............................................................................49
Guest Zone .................................................................51
Network ............................................................................. 52
USB Sharing .....................................................................54
Features ..................................................................................55
QoS Engine ....................................................................... 55
Firewall Settings .............................................................56
IPv4/IPv6 Rules ...............................................................58
Port Forwarding .............................................................59
Virtual Server ...................................................................60
Table of Contents
iiiD-Link DIR-882 User Manual
Table of Contents
Website Filter ................................................................... 61
Static Routes ....................................................................62
IPv6 .....................................................................................63
Dynamic DNS ..................................................................64
IPv6 Host .....................................................................65
QuickVPN ..........................................................................66
Management ........................................................................67
Time & Schedule ............................................................67
Time ..............................................................................67
Schedule .....................................................................68
System Log .......................................................................69
Admin.................................................................................70
System ...............................................................................71
User .....................................................................................72
Device (MAC Filtering) .................................................73
Upgrade ............................................................................74
Statistics ............................................................................75
Connect a Wireless Client to your Router ......................76
WPS Button ...................................................................................76
Windows® 10 ................................................................................77
Windows® 8 ................................................................................... 79
Windows® 7 ................................................................................... 81
WPA/WPA2 ............................................................................81
WPS ..........................................................................................84
Windows Vista® ............................................................................ 88
WPA/WPA2 ............................................................................89
Troubleshooting ..............................................................91
Wireless Basics .................................................................95
What is Wireless? ......................................................................... 96
Tips ...................................................................................................98
Wireless Modes ............................................................................99
Networking Basics .........................................................100
Check your IP address ............................................................ 100
Statically Assign an IP address ............................................ 101
Wireless Security ......................................................... 102
What is WPA? ................................................................ 102
Technical Specications ................................................103
Contacting Technical Support ......................................104
GPL Code Statement......................................................105
Warranty ......................................................................... 117
Registration ...................................................................124
1D-Link DIR-882 User Manual
Section 1 - Product Overview
Product Overview
Package Contents
Note: Using a power supply with a dierent voltage rating than the one included with the DIR-882 will cause damage and void the warranty
for this product.
If any of the above items are missing, please contact your reseller.
DIR-882-US AC2600 MU-MIMO Wi-Fi Router
Power Adapter
Ethernet Cable
Wi-Fi Conguration Card
Quick Install Guide
2D-Link DIR-882 User Manual
Section 1 - Product Overview
Network Requirements
• An Ethernet-based broadband modem
• IEEE 802.11ac/n/g/b/a wireless clients
• 10/100/1000 Ethernet devices
Web-based Conguration
Requirements
Computer with the following:
• Windows® or macOS operating system
• An installed Ethernet adapter or wireless adapter
Browser Requirements:
• Internet Explorer® 11 or higher
• Mozilla® Firefox®
• Google Chrome™
• Safari® 7 or higher
Windows® Users: Make sure you have the latest version of Java installed. Visit
www.java.com to download the latest version.
QRS Mobile Requirements
For requirements refer to QRS Mobile page at:
• iTunes Store (App Store > Utilities > D-Link Systems)
• Google Play (Click link to www.dlink.com/qrsmobileapp)
Minimum Requirements
3D-Link DIR-882 User Manual
Section 1 - Product Overview
Introduction
Overview
The AC2600 MU-MIMO Wi-Fi Router delivers premium performance for today’s most demanding tasks: HD streaming, gaming,
and multiple device usage. It comes packed with speeds of up to 2,533 Mbps (800 Mbps in 2.4GHz + 1,733 Mbps in 5GHz ), a
high-performance dual-core processor, AC SmartBeam technology, Intelligent Quality of Service (QoS) with trac prioritization,
four high-performance external antennas for maximum range, a new user interface, Smart Connect and with an easy setup. The
DIR-882 is the perfect combination of performance and ease of use.
Superior data rates, range and reliability
The AC2600 Wi-Fi Router comes with a 4x4 data streams which can support faster Wi-Fi speeds. These streams can be combined
through beamforming and MU-MIMO to increase reliability and range. This 4x4 AC router is the latest in AC technology, delivering
independent data streams to devices on the network for speeds of up to 2,533 Mbps. The AC2600 helps provide the best overall
performance to single devices that require high bandwidth such as video streaming or online gaming.
MU-MIMO Technology
The DIR-882 is designed to support MU-MIMO (Multi-User Multiple Input Multiple Output) technology that allows multiple devices
to get high-bandwidth Wi-Fi signal at the same time. You can stream HD media faster and play lag-free gaming. Compared to SU-
MIMO (Single-User Multiple Input Multiple Output) technology, MU-MIMO distributes data more eciently, giving you the fastest
Wi-Fi speeds in your home.
160 MHz Support
The DIR-882 is 160 MHz enabled. It doubles the bandwidth, optimizing the intense data transferring. Ideal for 4K HD streaming
and online gaming.
* Maximum wireless signal rate derived from IEEE Standard 802.11ac, 802.11a, 802.11g, and 802.11n specications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely aect wireless signal range. Multi-User MIMO (MU-MIMO) enabled clients needed for optimal performance.
4D-Link DIR-882 User Manual
Section 1 - Product Overview
Hardware Overview
Back
1 USB 2.0 Port Connect a USB ash drive to share content throughout your network. Supports USB 2.0 devices
2 LAN Ports (1-4) Connect Ethernet devices such as computers, switches, and game consoles.
3 Internet Port Connect your broadband modem to this port using an Ethernet cable.
4 Reset Button Press and hold the reset button with a paper clip for 10 seconds to reset the router to the factory
default settings.
5 WPS Button Press to start the WPS process.
6 Wi-Fi Button Press to turn on/o the wireless function.
7 Power Port Connect the supplied power adapter.
8 Power Button Press to power the router on and o.
3
4
5
2
17
6
8
5D-Link DIR-882 User Manual
Section 1 - Product Overview
Hardware Overview
LED
1Power LED A solid light indicates a proper connection to the power supply. The light will be a solid orange
during boot up.
2Internet LED A solid light indicates connection on the Internet port. If the LED is orange, the router cannot
connect to the Internet.
3Wireless
(2.4 GHz) LED A solid light indicates that the 2.4 GHz wireless band is enabled.
4Wireless
(5 GHz) LED A solid light indicates that the 5 GHz wireless band is enabled.
5USB 3.0 LED A solid white light indicates a USB 3.0 device is connected (front port).
6USB 2.0 LED A solid white light indicates a USB 2.0 device is connected (back port).
7USB 3.0 Port Connect a USB ash drive to share content throughout your network. Supports USB 3.0 and
USB 2.0 devices.
1
2
3
67
4
5
6D-Link DIR-882 User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the router
in an enclosed area such as a closet, cabinet, or in the attic or garage.
• Users with DSL providers - If you are using a PPPoE connection, you will need your PPPoE user name and password.
If you do not have this information, contact your ISP (Internet Service Provider). Do not proceed until you have this
information. Also, make sure you disable or uninstall any PPPoE software such as WinPoET, MacPoET, BroadJump,
or EnterNet 300 from your computer or you will not be able to connect to the Internet.
• Users with Cable providers - Make sure you unplug the power to your modem. In some cases, you may need to turn
it o for up to ve minutes.
• Advanced Users - If your ISP provided you with a modem/router combo, you will need to set it to “bridge” mode
so the DIR-882 can work properly. For details, contact your ISP or refer to the user manual for your modem/router
device.
7D-Link DIR-882 User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within the operating
range of your wireless network. Keep in mind that the number, thickness and location of walls, ceilings, or other objects that the
wireless signals must pass through may limit the range. Typical ranges vary depending on the types of materials and background
RF (radio frequency) noise in your home or business. The key to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a minimum -
each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your devices so that
the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (0.5 meters), at a 45-degree
angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters) thick!
Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle) for better
reception.
3. Building materials make a dierence. A solid metal door or aluminum studs may have a negative eect on range.
Try to position access points, wireless routers, and computers so that the signal passes through drywall or open
doorways. Materials and objects such as glass, steel, metal, walls with insulation, water (sh tanks), mirrors, le
cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate RF
noise.
5. If you are using 2.4 GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home security
systems), your wireless connection may degrade dramatically or drop completely. Make sure your 2.4 GHz phone
base is as far away from your wireless devices as possible. The base transmits a signal even if the phone is not
in use.
8D-Link DIR-882 User Manual
Section 2 - Installation
4 3 2 1 INTERNETUSB 2.0 RESET WPS WiFi 12V...1.5A POWER
- • +
1. Turn o and unplug the power to your cable or DSL modem. This is required.
Manual Setup
2. Connect an Ethernet cable from the Internet port of the router to the Ethernet port on your cable or DSL modem.
Modem
DIR-882
Internet Port (yellow)
Ethernet Cable
Modem
Ethernet Port
9D-Link DIR-882 User Manual
Section 2 - Installation
4 3 2 1 INTERNETUSB 2.0 RESET WPS WiFi 12V...1.5A POWER
- • +
4. Plug the power back into your DSL or cable modem. Please wait about one minute before continuing.
1 2 3 4 INTERNET 12V --1.5A POWER WPS
DIR-882
Computer
Ethernet Cable
Wireless Computer*
3. Connect another Ethernet cable from the Ethernet port on your computer to one of the LAN ports on the router. You
can also connect wirelessly to the router with your computer. Use the supplied Wi-Fi Conguration Card for the Wi-Fi
network name (SSID) and Wi-Fi password of the router. Complete steps 4 and 5 before attempting to connect.
Modem
Computer
DIR-882
1 2 3 4 INTERNET 12V --1.5A POWER WPS
Wireless Computer*
* If you are connecting wirelessly, you may now connect to the router using the supplied Wi-Fi Conguration Card for the Wi-Fi network name (SSID) and Wi-Fi password.
4 3 2 1 INTERNETUSB 2.0 RESET WPS WiFi 12V...1.5A POWER
- • +
10D-Link DIR-882 User Manual
Section 2 - Installation
4 3 2 1 INTERNETUSB 2.0 RESET WPS WiFi 12V...1.5A POWER
- • +
5. Plug the power adapter into your router and connect to an available power outlet or surge protector. If the LED
does not light up, press the Power button on the back of the router.
6. After the router has powered up, verify that the LED is lit. Proceed with router conguration.
Modem
DIR-882
Computer
Wireless
Computer
1 2 3 4 INTERNET 12V --1.5A POWER WPS
11D-Link DIR-882 User Manual
Section 3 - Conguration
There are several dierent ways you can congure your router to connect to the Internet and connect to your clients:
• D-Link Setup Wizard - This wizard will launch when you log into the router for the rst time using your web browser.
Refer to page 12.
• QRS Mobile App - Use your iPhone, iPad, iPod Touch, or Android device to congure your router. Refer to page 17.
• Manual Setup - Log into the router using a web browser and manually congure your router. Refer to page 21
Conguration
12D-Link DIR-882 User Manual
Section 3 - Conguration
The wizard will guide you through a step-by-step process to congure
your new D-Link router and connect to the Internet. When the welcome
screen appears, click Next to continue. Wait a few moments while your
router detects your Internet connection type.
Setup Wizard
If this is your rst time conguring the router, open your web browser (e.g.,
Internet Explorer, Chrome, Firefox, or Safari). This will automatically launch
the Setup Wizard. If the wizard does not start automatically, you can enter
http://dlinkrouter.local./ or the IP address of the router (192.168.0.1).
13D-Link DIR-882 User Manual
Section 3 - Conguration
If the router does not detect the type of Internet connection you have, you
will see a list of connection types. Select your Internet connection type. This
information can be obtained from your ISP (Internet Service Provider).
Select DHCP Connection (Dynamic IP Address) if your Internet connection
automatically provides you with an IP address. This option is commonly used
for cable modem services.
Click Next to continue.
If the router detected PPPoE or you selected Username/Password Connection
(PPPoE), enter your PPPoE username and password supplied by your ISP.
Click Next to continue.
Note: Make sure you remove your PPPoE software from your computer. The
software is no longer needed and will not work through a router.
14D-Link DIR-882 User Manual
Section 3 - Conguration
If the router detected or you selected Static IP Address Connection, enter
the IP information and DNS settings supplied by your ISP.
Click Next to continue.
For both the 2.4GHz and 5GHz bands, create a Wi-Fi network name (SSID)
using up to 32 characters.
Create a Wi-Fi password (between 8-63 characters). Your wireless devices
will need to have this passphrase or key entered to be able to connect to
your wireless network.
Click Next to continue.
15D-Link DIR-882 User Manual
Section 3 - Conguration
In order to secure your DIR-882, enter a new Admin Password. You will
be prompted for this password every time you want to use the router’s
web conguration utility.
Click Next to continue.
The Summary window will display your settings. Click Back if you nd it
necessary to make changes. When the settings are correct, make a note
of the of them so you can congure your Wi-Fi devices.
Click Next to continue.
16D-Link DIR-882 User Manual
Section 3 - Conguration
At the end of the wizard, you will see a nal summary of your settings.
Click Finish to close the wizard.
17D-Link DIR-882 User Manual
Section 3 - Conguration
QRS Mobile App
The QRS Mobile app allows you to install and congure your router from your mobile device.
Wi-Fi Name(SSID) 2.4Ghz:
dlink-xxxx
Wi-Fi Name(SSID) 5GHz:
dlink-xxxx-5GHz
Password: xxxxxxxx
To congure your router, go to:
http://dlinkrouter.local.
Or http://192.168.0.1
Username: “Admin”
Password:” “ (leave the eld blank)
Step 1
Search for the free QRS Mobile app on the App Store or Google Play.
Step 2
Once your app is installed, you may now congure your router. Connect
to the router wirelessly by going to your wireless utility on your device.
Scan for the Wi-Fi name (SSID) as listed on the supplied info card. Select
and then enter your Wi-Fi password.
Step 3
Once you connect to the router, tap on the QRS Mobile icon to launch
the QRS mobile app from your mobile device.
18D-Link DIR-882 User Manual
Section 3 - Conguration
Step 4
You will see the Welcome screen. Tap Start to proceed. When the Operation
Mode screen appears, tap Next.
Step 5
At this point, make sure that your router is connected to a modem. Plug
one end of the provided Ethernet cable into your DSL or cable modem,
and plug the other end into the port marked INTERNET on the DIR-882.
Tap Next to automatically detect your Internet connection and proceed
to the next step.
19D-Link DIR-882 User Manual
Section 3 - Conguration
Step 6
You will be prompted to set up each wireless frequency band; the 2.4GHz
band followed by the 5GHz band.
A. Enter a Network Name (SSID) of your choice, or you may leave it
unchanged to accept the default SSID. Each wireless band can be
assigned its own SSID.
B. Choose a Wi-Fi Password of at least eight characters. You will need
to enter this Password the rst time you connect any device to the
router wirelessly.
Tap Next to proceed.
Step 7
Enter the Device Password (Admin Password) of your choice. Unlike
the Wi-Fi password, this password is only required when you need to
congure the router. Refer to "Web-based Conguration Utility" on page
21 to learn how this password is used. Tap Next to proceed.
20D-Link DIR-882 User Manual
Section 3 - Conguration
Step 8
If you would like to receive notication whenever a new rmware update
is available, tap the Notify me when new rmware is available check
box and tap Next.
Otherwise, just tap Next to proceed.
Step 9
You will see a summary of your settings. If you need to make any changes,
tap Back to step back through the previous pages.
Otherwise, tap Next to complete the setup.
Congratulations, your device has been successfully congured! You may now exit the QRS Mobile app.
21D-Link DIR-882 User Manual
Section 3 - Conguration
Web-based Conguration Utility
Enter your password. If you did not create a password with the Setup Wizard, leave
the Admin Password eld blank by default. Click Log In to proceed.
Note: If you cannot remember your password and cannot log in, press the reset button
(see page 4) to restore the router to its factory default settings.
Open a web-browser (e.g., Internet Explorer, Chrome, Firefox, or Safari) and enter
http://dlinkrouter.local./ or the IP address of the router (http://192.168.0.1).
The router’s Home page will open, displaying its current connection status.
The bar at the top of the page has quick access to Settings, Features, and Management
functions. You may easily navigate back Home at any time.
Note: The system will automatically time-out after a period of inactivity. (You will have
to log back in as described above.)
22D-Link DIR-882 User Manual
Section 3 - Conguration
Home
The current status of the router is displayed on the Home page in the form of an interactive diagram. You can click on an icon to
see information about the selected part of the network at the bottom of the screen.
The Home page shows whether or not the router is currently connected to the
Internet. If disconnected, click on Click to repair to launch the Setup Wizard.
(Refer to "Setup Wizard" on page 12.)
To view details about your Internet connection, click on the Internet icon. Click Release
IP Address to disconnect from the Internet. If you do this and wish to reconnect, click
Renew.
To recongure the Internet settings, refer to "Internet" on page 26.
Internet
23D-Link DIR-882 User Manual
Section 3 - Conguration
DIR-882
Click on the DIR-882 icon to view details about the router and its wireless settings.
Here you can see the router’s current wireless settings, as well as its MAC address.
To recongure the router's network settings, either click Go to settings (at the bottom
left side of the page), or click Settings (at the top of the page) and then Network from
the drop-down menu that appears. Refer to page 52.
To recongure the router's wireless settings, either click Go to settings (at the bottom
right side of the page), or click Settings (at the top of the page) and then Wireless
from the drop-down menu that appears. Refer to page 49.
24D-Link DIR-882 User Manual
Section 3 - Conguration
Connected Clients
Click on the Connected Clients icon to view details about all the clients currently
connected to the router, and their corresponding IP addresses.
To edit a client’s settings, click the pencil icon for the client you would like to edit.
Enter a custom name for this client.
Displays the vendor of the device.
Enter a specic IP address for this client.
Enable if you would like to reserve this IP address for this client. Every
time this device joins the network, it will receive this IP address.
Enable to block access to your router and then select a schedule you
want the rule to be active from the drop-down menu.
Click Save when you are done.
Name:
Vendor:
IP Address:
Reserve IP:
Parental
Control:
25D-Link DIR-882 User Manual
Section 3 - Conguration
USB Device
Click on the USB Device icon to view details about the currently connected
USB device: DLNA media server, FTP server, and Windows File Sharing
(SAMBA).
If you have a USB device connected, you can see its name and how much
free space it has.
Click Go to Settings to take you to the USB Sharing section. Refer to
page 54.
26D-Link DIR-882 User Manual
Section 3 - Conguration
Settings
Wizard
Internet
From the Settings menu, you can click Wizard to open the Setup Wizard and connect to the Internet. This is the same wizard that you launched
when you rst installed the router.
From the Settings menu on the bar on the top of the page, click Internet to congure your Internet connection manually.
Choose your Internet Connection type from the drop-down menu.
Depending on the connection type that you select, you may also see
additional elds below that require input. For example, when you
select PPPoE, you will see elds for Username and Password.
My Internet
Connection is:
Click Advanced Settings... to expand the list and see all elds for the selected option.
For Dynamic IP (DHCP) refer to page 27.
For Static IP refer to page 28.
For PPPoE refer to page 29.
For PPTP refer to page 30.
For L2TP refer to page 32.
For DS-Lite refer to page 34.
27D-Link DIR-882 User Manual
Section 3 - Conguration
The Host Name is optional but may be required by some ISPs. Leave
it blank if you are not sure.
Enter the Primary DNS Server IP address assigned by your ISP. This
address is usually obtained automatically from your ISP.
Enter the Secondary DNS Server IP address assigned by your ISP. This
address is usually obtained automatically from your ISP.
Maximum Transmission Unit - by default this eld will be set to Auto.
Select Manual if you need to change the MTU for optimal performance
with your ISP.
The default MAC address is set to the Internet port’s physical interface
MAC address on the router. You can use the drop-down menu to
replace the Internet port’s MAC address with the MAC address of a
connected client.
Click Save when you are done.
Host Name:
Primary DNS
Server:
Secondary DNS
Server:
MTU:
MAC Address
Clone:
Dynamic IP (DCHP)
Select Dynamic IP (DHCP) to obtain IP address information automatically from your Internet Service Provider (ISP). Select this option if your ISP
does not provide you with an IP address to use.
28D-Link DIR-882 User Manual
Section 3 - Conguration
Enter the IP Address provided by your ISP.
Enter the Subnet Mask provided by your ISP.
Enter the Default Gateway address provided by your ISP.
Enter the Primary DNS Server IP address assigned by your ISP.
Enter the Secondary DNS Server IP address assigned by your ISP.
Maximum Transmission Unit - by default this eld will be set to Auto.
Select Manual if you need to change the MTU for optimal performance
with your ISP.
The default MAC address is set to the Internet port’s physical interface
MAC address on the router. You can use drop-down menu to replace
the Internet port’s MAC address with the MAC address of a connected
client.
Click Save when you are done.
IP Address:
Subnet Mask:
Default
Gateway:
Primary DNS
Server:
Secondary DNS
Server:
MTU:
MAC Address
Clone:
Static IP
Select Static IP if your IP information is provided by your Internet service provider (ISP). Each IPv4 address must be entered in the appropriate form,
known as dot-decimal notation. This means four decimal numbers separated by dots (x.x.x.x).
29D-Link DIR-882 User Manual
Section 3 - Conguration
Enter the Username provided by your ISP.
Enter the Password provided by your ISP.
Select either Always on, On demand, or Manual.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable Auto-
reconnect.
Select Static IP if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic IP.
Enter the IP Address provided by your ISP (Static IP only).
Enter the ISP Service Name (optional).
Enter the Primary DNS Server IP address assigned by your ISP.
Enter the Secondary DNS Server IP address assigned by your ISP.
Maximum Transmission Unit - by default this eld will be set to Auto.
Select Manual if you need to change the MTU for optimal performance.
The default MAC address is set to the Internet port’s physical interface
MAC address on the router. You can use drop-down menu to replace the
Internet port’s MAC address with the MAC address of a connected client.
Click Save when you are done.
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Address Mode:
IP Address:
Service Name:
Primary DNS
Server:
Secondary DNS
Server:
MTU:
MAC Address
Clone:
Select PPPoE (Point to Point Protocol over Ethernet) if your Internet connection requires you to enter a username and password. This information
can be provided by your Internet service provider (ISP). This option is typically used for DSL services.
PPPoE
30D-Link DIR-882 User Manual
Section 3 - Conguration
Enter the PPTP Server IP Address provided by your ISP.
Enter the Username provided by your ISP.
Enter the Password provided by your ISP.
Select either Always on, On demand, or Manual.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable Auto-
reconnect.
Select Static IP if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic IP.
Enter the PPTP IP Address provided by your ISP (for Static IP only).
Enter the PPTP Subnet Mask provided by your ISP (for Static IP only).
Enter the PPTP Gateway IP Address provided by your ISP (for Static
IP only).
Enter the Primary DNS Server IP address assigned by your ISP.
Enter the Secondary DNS Server IP address assigned by your ISP.
PPTP Server IP
Address:
Username:
Password:
Reconnect
Mode:
Maximum Idle
Time:
Address Mode:
PPTP IP
Address:
PPTP Subnet
Mask:
PPTP Gateway
IP Address:
Primary DNS
Server:
Secondary DNS
Server:
Choose PPTP (Point-to-Point-Tunneling Protocol) if your Internet Service Provider (ISP) uses a PPTP connection. Your Internet service provider (ISP)
can provide you with a username and password.
PPTP
31D-Link DIR-882 User Manual
Section 3 - Conguration
Maximum Transmission Unit - by default this eld will be set to
Auto. Select Manual if you need to change the MTU for optimal
performance with your ISP.
Click Save when you are done.
MTU:
32D-Link DIR-882 User Manual
Section 3 - Conguration
L2TP
Enter the L2TP Server IP Address provided by your ISP.
Enter the Username provided by your ISP.
Enter the Password provided by your ISP.
Select either Always on, On demand, or Manual.
Enter a maximum idle time during which the Internet connection
is maintained during inactivity. To disable this feature, enable
Auto-reconnect.
Select Static IP if your ISP assigned you the IP address, subnet
mask, gateway, and DNS server addresses. In most cases, select
Dynamic IP.
Enter the L2TP IP Address provided by your ISP (for Static IP only).
Enter the L2TP Subnet Mask provided by your ISP (for Static IP
only).
Enter the L2TP Gateway IP Address provided by your ISP (for
Static IP only).
Enter the Primary DNS Server IP address assigned by your ISP.
Enter the Secondary DNS Server IP address assigned by your ISP.
L2TP Server IP
Address:
Username:
Password:
Reconnect Mode:
Maximum Idle
Time:
Address Mode:
L2TP IP Address:
L2TP Subnet
Mask:
L2TP Gateway IP
Address:
Primary DNS
Server:
Secondary DNS
Server:
Choose L2TP (Layer 2 Tunneling Protocol) if your Internet Service Provider (ISP) uses a L2TP connection. Your ISP can provide you with a username
and password.
33D-Link DIR-882 User Manual
Section 3 - Conguration
Maximum Transmission Unit - by default this eld will be set to
Auto. Select Manual if you need to change the MTU for optimal
performance with your ISP.
Click Save when you are done.
MTU:
34D-Link DIR-882 User Manual
Section 3 - Conguration
DS-Lite
Select DS-Lite DHCPv6 Option to let the router allocate the AFTR
IPv6 address automatically. Select Manual Conguration to enter
the AFTR IPv6 address manually.
If you selected Manual Conguration above, enter the AFTR IPv6
address used here.
Enter the B4 IPv4 address value used here.
Once connected, the WAN IPv6 address will be displayed here.
Once connected, the IPv6 WAN Default Gateway address will be
displayed here.
Click Save when you are done.
DS-Lite
Conguration:
AFTR IPv6
Address:
B4 IPv6
Address:
WAN IPv6
Address:
IPv6 WAN
Default
Gateway:
DS-Lite is an IPv6 (Internet Protocol version 6) connection type. DHCPv6 is the IPv6 equivalent of Dynamic Host Conguration Protocol for IPv4.
35D-Link DIR-882 User Manual
Section 3 - Conguration
IPv6
Choose your IPv6 Internet Connection type from the drop-down
menu. For most of the connection types, after you make a selection
you will see additional elds below that require input. The exception
is for Local Connectivity Only. For this connection type you must
click on Advanced Settings... to see the additional elds below.
My Internet
Connection Is:
Click Advanced Settings... to expand the list and see all elds for the selected option.
For Auto Detection refer to page 36.
For Static IPv6 refer to page 37.
For Auto Conguration (SLAAC/DHCPv6) refer to page 39.
For PPPoE refer to page 40.
For IPv6 in IPv4 Tunnel refer to page 42.
For 6 to 4 refer to page 44.
For 6rd refer to page 45.
For Local Connectivity Only refer to page 47.
36D-Link DIR-882 User Manual
Section 3 - Conguration
Auto Detection
Select Obtain DNS server address or Use the following DNS.
If you selected Use the following DNS, enter the Primary DNS
Server address.
If you selected Use the following DNS, enter the Secondary DNS
Server address.
Enable or disable prex delegation services.
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for
the router.
Displays the router’s LAN IPv6 Link-Local Address.
Enable or disable the Automatic IPv6 Address Assignment feature.
Enable or disable Automatic DHCP-PD in LAN services.
Select SLAAC + RDNSS, SLAAC + Stateless DHCP, or Stateful
DHCPv6.
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-PD:
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconguration
Type:
Router
Advertisement
Lifetime:
This is a connection method where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISPs require you to
change some settings on your side before your router can connect to the IPv6 Internet.
37D-Link DIR-882 User Manual
Section 3 - Conguration
Static IPv6
Enable or disable the Link-Local Address. (If you enable this option,
you can skip the description of the next two elds.)
If you disabled Use Link-Local Address, enter the IPv6 Address
supplied by your ISP.
If you disabled Use Link-Local Address, enter the Subnet Prex
Length supplied by your ISP.
Enter the Default Gateway for your IPv6 connection.
Enter the Primary DNS Server address.
Enter the Secondary DNS Server address.
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN IPv6 Link-Local Address.
Enable or disable the Automatic IPv6 Address Assignment feature.
Select SLAAC + RDNSS, SLAAC + Stateless DHCP, or Stateful
DHCPv6.
Use Link-Local
Address:
IPv6 Address:
Subnet Prex
Length:
Default Gateway:
Primary DNS
Server:
Secondary DNS
Server:
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Autoconguration
Type:
Select Static IP if your IPv6 information is provided by your Internet service provider (ISP).
38D-Link DIR-882 User Manual
Section 3 - Conguration
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
Router
Advertisement
Lifetime:
39D-Link DIR-882 User Manual
Section 3 - Conguration
Auto Conguration
Select either Obtain DNS server address or Use the following
DNS .
If you selected Use the following DNS address above, enter the
Primary DNS Server address.
If you selected Use the following DNS address above, enter the
Secondary DNS Server address.
Enable or disable prex delegation services.
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for
the router.
Displays the router’s LAN Link-Local Address.
Enable or disable the Automatic IPv6 Address Assignment
feature.
Enable or disable Automatic DHCP-PD in LAN services.
Select SLAAC + RDNSS, SLAAC + Stateless DHCP, or Stateful
DHCPv6.
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-PD:
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconguration
Type:
Router
Advertisement
Lifetime:
Auto Conguration is a connection method where the ISP assigns your IPv6 address when your router requests one from the ISP’s server. Some ISPs
require you to change some settings on your side before your router can connect to the IPv6 Internet.
40D-Link DIR-882 User Manual
Section 3 - Conguration
PPPoE
Choose Share with IPv4 to re-use your IPv4 PPPoE username and
password, or Create a new session.
If you selected Create a new session above, enter the PPPoE
Username provided by your ISP.
If you selected Create a new session above, enter the PPPoE
Password provided by your ISP.
Select Static IP if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic IP.
Enter the IP Address provided by your ISP (for Static IP only).
If you selected Create a new session above, enter the ISP Service
Name (optional).
If you selected Create a new session above, select either Always
on, On demand, or Manual.
Maximum Transmission Unit - you may need to change the MTU for
optimal performance with your ISP.
Select either Obtain DNS server address or Use the following DNS .
If you selected Use the following DNS, enter the Primary DNS
Server address.
If you selected Use the following DNS, enter the Secondary DNS
Server address.
PPPoE Session:
Username:
Password:
Address Mode:
IP Address:
Service Name:
Reconnect
Mode:
MTU:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Select PPPoE (Point-to-Point-Tunneling Protocol) if your Internet connection requires you to enter a username and password. This information can be
provided by your Internet service provider (ISP). Required elds will vary, depending on the options you have enabled.
41D-Link DIR-882 User Manual
Section 3 - Conguration
Enable or disable prex delegation services.
Enter the LAN (local) IPv6 address for the router. (This eld is only
required when DHCP-PD is disabled.)
Displays the router’s LAN IPv6 Link-Local Address.
Enable or disable the Automatic IPv6 Address Assignment feature.
Select SLAAC + RDNSS, SLAAC + Stateless DHCP or Stateful DHCPv6.
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
Enable
DHCP-PD:
LAN IPv6
Address:
LAN IPv6 Link-
Local Address:
Enable
Automatic
IPv6 Address
Assignment:
Auto
Conguration
Type:
Router
Advertisement
Lifetime:
42D-Link DIR-882 User Manual
Section 3 - Conguration
IPv6 in IPv4 Tunnel
Enter the Remote IPv4 address you will use.
Enter the Remote IPv6 address you will use.
Displays the Local IPv4 address.
Enter the Local IPv6 address you will use.
Enter the Subnet Prex Length supplied by your ISP.
Select either Obtain DNS server address or Use the following DNS.
If you selected Use the following DNS above, enter the Primary
DNS Server address.
If you selected Use the following DNS above, enter the Secondary
DNS Server address.
Enable or disable prex delegation services.
If you disabled DHCP-PD, enter the LAN (local) IPv6 address for the
router.
Displays the router’s LAN IPv6 Link-Local Address.
Remote IPv4
Address:
Remote IPv6
Address:
Local IPv4
Address:
Local IPv6
Address:
Subnet Prex
Length:
DNS Type:
Primary DNS
Server:
Secondary DNS
Server:
Enable DHCP-
PD:
LAN IPv6
Address:
LAN IPv6 Link-
Local Address:
You can congure the IPv6 connection to run in IPv4 Tunnel mode. IPv6 over IPv4 tunneling encapsulates IPv6 packets in IPv4 packets so that IPv6
packets can be sent over an IPv4 infrastructure.
43D-Link DIR-882 User Manual
Section 3 - Conguration
Enable or disable the Automatic IPv6 Address Assignment
feature.
Enable or disable Automatic DHCP-PD in LAN services.
Select SLAAC + RDNSS, SLAAC + Stateless DHCP, or Stateful
DHCPv6.
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
Enable Automatic
IPv6 Address
Assignment:
Enable Automatic
DHCP-PD in LAN:
Autoconguration
Type:
Router
Advertisement
Lifetime:
44D-Link DIR-882 User Manual
Section 3 - Conguration
6 to 4
Displays the 6to4 Address.
Enter the 6to4 Relay supplied by your ISP.
Enter the Primary DNS Server address.
Enter the Secondary DNS Server address.
Enter the LAN (local) IPv6 address for the router.
Displays the router’s LAN IPv6 Link-Local Address.
Click to enable the Automatic IPv6 Address Assignment feature.
Select SLAAC + RDNSS or SLAAC + Stateless DHCP, or Stateful
DHCPv6.
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
6to4 Address:
6to4 Relay:
Primary DNS
Server:
Secondary DNS
Server:
LAN IPv6 Address:
LAN IPv6 Link-
Local Address:
Enable Automatic
IPv6 Address
Assignment:
Autoconguration
Type:
Router
Advertisement
Lifetime:
In this section, the user can congure the IPv6 6 to 4 connection settings. 6 to 4 is an IPv6 address assignment and automatic tunneling technology
that is used to provide unicast IPv6 connectivity between IPv6 sites and hosts across the IPv4 Internet.
45D-Link DIR-882 User Manual
Section 3 - Conguration
6rd
Currently unsupported.
Enter the Primary DNS Server address.
Enter the Secondary DNS Server address.
Enable if you want to minimize the number of routes to the
destination by using a hub and spoke method of networking.
Choose the 6rd DHCPv4 Option to automatically populate the data
values, or Manual Conguration to enter the settings manually.
Enter the 6rd IPv6 Prex and mask length supplied by your ISP (for
manual conguration only).
Displays the WAN IPv4 Address. Enter the mask length (for manual
conguration only).
Enter the 6rd border relay IPv4 Address supplied by your ISP (for
manual conguration only).
Displays the LAN (local) IPv6 address for the router.
Displays the router’s LAN Link-Local Address.
Assign IPv6
Prex:
Primary DNS
Server:
Secondary DNS
Server:
Enable Hub and
Spoke Mode:
6rd
Conguration:
6rd IPv6 Prex:
WAN IPv4
Address:
6rd Border
Relay IPv4
Address:
LAN IPv6
Address:
LAN IPv6 Link-
Local Address:
In this section, the user can congure the IPv6 6rd connection settings.
46D-Link DIR-882 User Manual
Section 3 - Conguration
Click to enable the Automatic IPv6 Address Assignment feature.
Select SLAAC + RDNSS, SLAAC + Stateless DHCP, or Stateful
DHCPv6.
Enter the IPv6 address lifetime (in minutes).
Click Save when you are done.
Enable Automatic
IPv6 Address
Assignment:
Autoconguration
Type:
Router
Advertisement
Lifetime:
47D-Link DIR-882 User Manual
Section 3 - Conguration
Local Connectivity Only
Click to enable Unique Local IPv6 Unicast Addresses settings.
When ULA is enabled, you may also enable automatic conguration
of the ULA prex.
Will display the Current ULA Prex.
Will display the LAN IPv6 ULA.
Click Save when you are done.
Enable ULA:
Use Default
ULA Prex:
Current ULA
Prex:
LAN IPv6 ULA:
Local Connectivity Only allows you to set up an IPv6 connection that will not connect to the Internet. For this Internet Connection type, you must
click on Advanced Settings... to see the required elds below.
48D-Link DIR-882 User Manual
Section 3 - Conguration
Triple-Play VLAN
Click to enable Triple-Play VLAN.
Click to set a priority to each VLAN ID.
Enter the VLAN ID for each service.
If enabled, select the priority for each service. Priority tags are between
0 to 7 with 0 being assigned to the lowest priority and 7 assigned to
the highest.
Select which port/band you want to assign each service from the drop-
down menu.
Enable:
Priority ID:
VLAN IDs:
Priority:
Interface Trac
Type Setting:
Triple-Play is the delivery of Internet, Voice over IP (VoIP), and IPTV (video multicast) data by your ISP.
49D-Link DIR-882 User Manual
Section 3 - Conguration
Wireless
Enable or disable Smart Connect. If enabled, you can enter one Wi-
Fi network/password for both wireless bands and the router will
automatically select which band your wireless clients will connect
to. If you want to have dierent Wi-Fi network names for each band,
select Disable.
Create a Wi-Fi Name for your wireless network using up to 32
characters.
Create a Password to use for wireless security. Wireless clients will
need to enter this password to successfully connect to the network.
Select None, WEP, or WPA/WPA2-Personal (recommended).
Select the preferred wireless networking standard for each band.
The available options will depend on the wireless frequency band,
as well as the currently selected security mode.
Select the desired channel. The default is Auto (recommended).
Select the desired wireless transmission power (High, Medium or
Low).
Status:
Wi-Fi Name
(SSID):
Password:
Security Mode:
802.11 Mode:
Wi-Fi Channel:
Transmission
Power:
From the Settings menu, click Wireless to begin wireless conguration. You will see the Wi-Fi Name (SSID) and Password for both the 2.4GHz and 5GHz
bands. Click Advanced Settings... to expand the list and allow you to view all elds corresponding with each frequency band.
The following options apply to both the 2.4GHz and the 5GHz wireless frequency bands:
Advanced Settings
50D-Link DIR-882 User Manual
Section 3 - Conguration
For the 2.4GHz band:
Select Auto 20/40 MHz if you are using both 802.11n and non-802.11n
wireless devices, or select 20 MHz if you are not using any 802.11n
wireless clients.
For the 5GHz band:
Select Auto 20/40/80 MHz if you are using 802.11ac, 802.11n, and
non-802.11n wireless devices, or select Auto 20/40 MHz if you are
using both 802.11n and non-802.11n wireless devices.
Enable this option to reduce interference from other wireless networks
in your area. If the channel width is operating at 40MHz and there
is another wireless network's channel over-lapping and causing
interference, the router will automatically change to 20MHz.
The default setting is Visible. Select Invisible if you do not want to
broadcast the SSID of your wireless network.
Use the drop-down menu to select a schedule for enabling the rule.
The schedule may be set to Always Enable, or you can create your
own schedules in the Schedules section (refer to page 68).
Click Save when you are done.
Channel Width:
HT20/40
Coexistence
(2.4 GHz only)
Visibility Status:
Schedule:
51D-Link DIR-882 User Manual
Section 3 - Conguration
Guest Zone
Enable or disable the Guest Zone for each wireless frequency band.
Enter a wireless network name (SSID) that is dierent from your main
wireless network.
Create a Password to use for wireless security. Wireless clients will
need to enter this password to successfully connect to the guest zone.
Enabling this option will limit connectivity to the Internet. Guests
will not be allowed to access other local network devices.
Click Save when you are done.
Status:
Wi-Fi Name
(SSID):
Password:
Internet Access
Only:
The following options apply to both the 2.4GHz and the 5GHz wireless frequency
bands:
To congure a Guest Zone, click on the Guest Zone link. You may congure dierent zones for the 2.4 GHz and 5 GHz wireless bands.
A Guest Zone is a temporary zone that can be used by guests to access the Internet. Guest Zones are separate from your main wireless network.
52D-Link DIR-882 User Manual
Section 3 - Conguration
Network
Enter the LAN IP Address of the router. The default IP address is
192.168.0.1.
If you change the IP address, once you click Save, you will need
to enter the new IP address in your browser to get back into the
conguration utility.
Enter the Subnet Mask of the router. The default subnet mask is
255.255.255.0.
The default address to access the router’s conguration utility is
http://dlinkrouter.local./ You may replace dlinkrouter with a name
of your choice by entering it into this eld.
Enter the Local Domain Name (optional).
If enabled, your computers will use the router for a DNS server.
Disable to transfer the DNS server information from your ISP to your
computers.
LAN IP Address:
Subnet Mask:
Management
Link:
Local Domain
Name:
Enable DNS
Relay:
This section allows you to change the local network settings of the router and to congure the DHCP (Dynamic Host Control Protocol) settings. You
can enable the use of the DIR-882 as a DNS server. From the Settings menu, click Network.
Click Advanced Settings to expand the list and see all of the available options.
53D-Link DIR-882 User Manual
Section 3 - Conguration
Status:
DHCP IP
Address Range:
DHCP Lease
Time:
Always
Broadcast:
WAN Port
Speed:
UPnP:
IPv4 Multicast
Streams:
IPv6 Multicast
Streams:
Enable or disable the DHCP server.
Enter the starting and ending IP addresses for the DHCP server’s IP
assignment.
Note: If you statically (manually) assign IP addresses to your computers
or devices, make sure the IP addresses are outside of this range or you
may have an IP conict.
Enter the length of time for the IP address lease in minutes.
Enable this feature to broadcast your networks DHCP server to LAN/
WLAN clients.
You may set the port speed of the Internet port to 10 Mbps, 100
Mbps, 1000 Mbps, or Auto (recommended).
Enable or disable Universal Plug and Play (UPnP). UPnP provides
compatibility with networking equipment, software and peripherals.
Enable to allow IPv4 multicast trac to pass through the router from
the Internet.
Enable to allow IPv6 multicast trac to pass through the router from
the Internet.
Click Save when you are done.
54D-Link DIR-882 User Manual
Section 3 - Conguration
USB Sharing
This page will allow you to set up access to files on an external USB drive plugged into the router. You can do this through
the local network or from the Internet. In the Settings menu on the bar on the top of the page, click USB Sharing.
Click User at the top to create user accounts to access the below services. Refer to page 72.
Status:
DLNA Media Server:
Windows File Sharing
(SAMBA):
FTP Server:
Enable Remote
Sharing:
FTP Server Port:
Idle Time:
Click to enable DLNA media server functions, allowing connected
clients access to media les over the network.
Create a name for your DLNA media server.
Click to enable local le sharing.
Click to enable and then click Advanced Settings if you want
users from outside your local network to access les on your
USB drive.
Enable to allow users from the Internet to access your USB drive.
Enter a port for your FTP server. Default is 21.
Enter the time in minutes where the user will be logged o if idle.
Default is 5 minutes.
55D-Link DIR-882 User Manual
Section 3 - Conguration
Features
QoS Engine
Under Connected Clients, you will see client cards representing each device. If some
client cards are o-screen, you can use the < and > buttons to scroll left and right.
A maximum of one device can be assigned Highest priority.
A maximum of two devices can be assigned High priority.
A maximum of eight devices can be assigned Medium priority.
If connected clients are not assigned a priority, all devices will be treated with equal
priority. If some devices are assigned a priority and others are not, the unassigned
devices will be treated with the lowest priority.
Quality of Service (QoS) improves data ow. It allows you to prioritize clients, so that high-priority clients receive higher bandwidth. For example, if
one client is streaming a movie and another is downloading a non-urgent le, you might wish to assign the former client a higher priority, so that
the movie streaming is not disrupted by the trac of the other devices on the network.
From the Features menu on the bar on the top of the page, click QoS Engine.
To assign a priority level to a device, drag the device card from the Connected Clients
list over an empty slot and release the mouse button. The card will remain in the
slot. If you want to remove a priority assignment from a device and return it to the
Connected Clients list, click the cross icon in the top right corner of the device card.
Click Save when you are done.
56D-Link DIR-882 User Manual
Section 3 - Conguration
Firewall Settings
Enable or disable Demilitarized Zone (DMZ). Enabling this feature
creates a subnetwork that can be used to expose a single computer
to the Internet for applications that do not run well behind the router.
This may expose the computer to a variety of security risks and is
not recommended.
If you enabled DMZ, enter the IP Address of the client you wish to
expose, or select a Computer Name from the drop-down menu.
Click to enable Stateful Packet Inspection (SPI) to help prevent cyber
attacks. This technique validates that the trac passing through the
session conforms to the protocol.
Click to enable Anti-Spoof Checking, which will protect your
network from certain kinds of “spoong” attacks.
Click to enable IPv6 Simple Security, which will provide simple
security capabilities for a local-area IPv6 network.
Click to enable IPv6 Ingress Filtering, which will verify the incoming
packets are coming from the network from which they claim to
originate.
Enable DMZ:
DMZ IP
Address:
Enable SPI IPv4:
Enable
Anti-Spoof
Checking:
IPv6 Simple
Security:
IPv6 Ingress
Filtering:
A rewall protects your network from malicious attacks over the Internet. The DIR-882 oers a high-performance rewall features like SPI (Stateful
Packet Inspection).
From the Features menu, click Firewall.
Click Advanced Settings to expand the list and view more options.
57D-Link DIR-882 User Manual
Section 3 - Conguration
Click to enable PPTP, which will allow multiple machines on the
LAN to connect to their corporate network using the PPTP protocol.
Enable to allow multiple VPN clients to connect to their corporate
network using IPSec. Some VPN clients support traversal of IPSec
through NAT. This Application Level Gateway (ALG) may interfere
with the operation of such VPN clients. If you are having trouble
connecting with your corporate network, try turning this ALG o.
Check with the system administrator of your corporate network to
nd out whether your VPN client supports NAT traversal.
Enable to allow applications that use Real Time Streaming Protocol
(RTSP) to receive streaming media from the Internet.
Enable to allow devices and applications using VoIP (Voice over IP)
to communicate across NAT. Some VoIP applications and devices
have the ability to discover NAT devices and work around them. This
Application Level Gateway (ALG) may interfere with the operation of
such devices. If you are having trouble making VoIP calls, try turning
this ALG o.
Click Save when you are done.
PPTP:
IPSec (VPN):
RTSP:
SIP:
58D-Link DIR-882 User Manual
Section 3 - Conguration
IPv4/IPv6 Rules
Enter a Name for the new rule.
Enter the Source IP Address Range that the rule applies to. Using
the drop-down menu, specify whether it is a WAN or LAN IP address.
Enter the Destination IP Address Range that the rule applies to.
Using the drop-down menu, specify whether it is a WAN or LAN IP
address.
Select the protocol of the trac to allow or deny (Any, TCP, or UDP)
and then enter the range of ports that the rule will apply to.
Use the drop-down menu to select a Schedule when the rule will
be enabled. The schedule may be set to Always Enable, or you can
create a schedule from the Schedules section (refer to page 68).
Click Apply when you are done.
The IPv4/IPv6 Rules section allows you to specify the kind of trac that is allowed to pass through the network. Click either IPv4 Rules or IPv6 Rules.
Name:
Source IP
Address Range:
Destination IP
Address Range:
Port Range:
Schedule:
Use the drop-down menu to select whether you want to Turn IPv4 Filtering ON and
ALLOW or DENY the rules you create. Or you may choose to Turn IPv4 Fltering OFF.
If you wish to remove a rule, click on its trash can icon in the Delete column. If you wish
to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new rule,
click Add Rule. Click Save when you are done.
When you click on Add Rule, the Create New Rule window will open. Enter the required
information into the elds described below:
59D-Link DIR-882 User Manual
Section 3 - Conguration
Port Forwarding
Enter a Name for the new rule.
Enter the IP address of the computer on your local network that
you want to allow the incoming service to. Or, select the Computer
Name from the drop-down menu.
Enter a TCP Port (or a range of TCP ports) you want to open. Separate
ports with a comma (for example: 24,1009,3000-4000).
Enter a UDP Port (or a range of UDP ports) you want to open.
Separate ports with a comma (for example: 24,1009,3000-4000).
Use the drop-down menu to select a Schedule when the rule will
be enabled. The schedule may be set to Always Enable, or you can
create a schedules from the Schedules section (refer to page 68).
Click Apply when you are done.
Name:
Local IP:
TCP Port:
UDP Port:
Schedule:
If you wish to remove a rule, click on its trash can icon in the Delete column. If you
wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a
new rule, click Add Rule. Click Save when you are done.
When you click on Add Rule, the Create New Rule window will open. Enter the required
information into the elds described below:
Port forwarding allows you to specify a single port or a range of ports to open for specic devices on the network. It allows trac requests from a
specic application to be directed to a specic client.
From the Features menu, click Port Forwarding.
60D-Link DIR-882 User Manual
Section 3 - Conguration
Virtual Server
Enter a Name for the new rule or select an application from the
drop-down menu.
Enter the IP address of the computer on your local network that
you want to allow the incoming service to. Or, select the Computer
Name from the drop-down menu.
Select the protocol of the trac to allow or deny (TCP, UDP, Both,
or Other).
If you selected Other, enter the Protocol Number.
Enter the public port you want to open.
Enter the private port you want to open.
Use the drop-down menu to select a schedule when the rule will
be enabled. The schedule may be set to Always Enable, or create
your own schedule from the Schedules section (refer to page 68).
Click Apply when you are done.
The DIR-882 can store a maximum of 15 rules. If you wish to remove a rule, click on
its trash can icon in the Delete column. If you wish to edit a rule, click on its pencil
icon in the Edit column. If you wish to create a new rule, click the Add Rule button.
Click Save when you are done.
When you click on Add Rule, the Create New Rule window will open. Enter the required
information into the elds described below:
Name:
Local IP:
Protocol:
Protocol
Number:
External Port:
Internal Port:
Schedule:
The Virtual Server allows you to specify a single public port for redirection to an internal LAN IP Address and Private LAN port.
From the Port Forwarding page click Virtual Server.
61D-Link DIR-882 User Manual
Section 3 - Conguration
Website Filter
The website lter setting allows you to block access to certain web sites. You can
either create a list of sites to block, or create a list of sites to allow (with all other sites
being blocked).
In the Features menu on the bar on the top of the page, click Website Filter.
If you want to create a list of sites to block, select DENY computers access to ONLY
these sites from the drop-down menu. All other sites will be accessible. If you want
to specify a list of sites to allow, select ALLOW computers access to ONLY these
sites from the drop-down menu. All other sites will be blocked.
You may specify a maximum of fteen web sites. To add a new site to the list, click
Add Rule. Next, under Website URL/Domain enter the URL or domain. If you wish
to remove a rule, click on its trash can icon in the Delete column. If you wish to edit
a rule, simply replace the URL or domain.
Click Save when you are done.
62D-Link DIR-882 User Manual
Section 3 - Conguration
Static Routes
Enter a Name for the new rule.
Enter the IP address of packets that will take this route.
Enter the netmask of the route.
Enter your next hop gateway to be taken if this route is used.
The route metric is a value from 1 to 16 that indicates the cost of
using this route. A value 1 is the lowest cost and 15 is the highest cost.
Select the interface that the IP packet must use to transit out of the
router when this route is used.
Click Apply when you are done.
To congure IPv6 rules, click IPv6 and refer to page 63. To return to the main IPv4
static routes page, click IPv4.
If you wish to remove a route, click on its trash icon in the Delete column. If you wish
to edit a route, click on its pencil icon in the Edit column. If you wish to create a new
route, click the Add Route button. Click Save when you are done.
When you click on Add Route, the Create New Route window will open. Enter the
required information into the elds described below:
Name:
Destination
Network:
Mask:
Gateway:
Metric:
Interface:
The Static Routes section allows you to dene custom routes allowing trac to be directed to a specic client or location.
From the Features menu, click Static Route.
63D-Link DIR-882 User Manual
Section 3 - Conguration
Enter a Name for the new rule.
This is the IP address of the router used to reach the specied
destination.
Enter the IPv6 address prex length of the packets that will take this
route.
Enter the IPv6 gateway address. This is the next hop that will be taken
if this route is used.
The route metric is a value from 1 to 16 that indicates the cost of
using this route. A value 1 is the lowest cost and 15 is the highest cost.
Select the interface that the IP packet must use to transit out of the
router when this route is used.
Click Apply when you are done.
Name:
DestNetwork:
PrexLen:
Gateway:
Metric:
Interface:
IPv6
If you wish to remove a route, click on its trash can icon in the Delete column. If you
wish to edit a route click on its pencil icon in the Edit column. If you wish to create a
new route, click the Add Route button. Click Save when you are done.
When you click on Add Route, the Create New Route window will open. Enter the
required information into the elds described below:
64D-Link DIR-882 User Manual
Section 3 - Conguration
Dynamic DNS
Most Internet Service Providers (ISPs) assign dynamic (changing) IP addresses. Using a Dynamic DNS (DDNS) service provider, people can enter
your domain name in their web browser to connect to your server, no matter what your current IP address assignment.
From the Features menu, click Dynamic DNS.
Enabling DDNS will reveal additional conguration options.
Displays the current dynamic DNS connection Status.
Enter the address of your dynamic DNS server, or select one from
the drop-down menu.
Enter the Host Name that you registered with your dynamic DNS
service provider.
Enter your dynamic DNS User Name.
Enter your dynamic DNS Password.
Enter a Time Out (in hours).
Click Save when you are done.
Enable
Dynamic DNS:
Status:
Server Address:
Host Name:
User Name:
Password:
Time Out:
At the bottom of the page are the IPv6 host settings. To congure an IPv6 dynamic
DNS host, refer to page 65.
65D-Link DIR-882 User Manual
Section 3 - Conguration
Enter the Host Name that you registered with your dynamic DNS
service provider.
Enter the IPv6 Address of the dynamic DNS server. Or, select the
Computer Name from the drop-down menu.
Click Apply when you are done.
Host Name:
IPv6 Address:
The IPv6 host settings are found at the bottom of the Dynamic DNS page.
If you wish to remove a rule, click on its trash can icon in the Delete column. If you
wish to edit a rule, click on its pencil icon in the Edit column. If you wish to create a
new rule, click the Add Record button. Click Save when you are done.
When you click on Add Record, the Create New Record window will open. Enter the
required information into the elds described below:
IPv6 Host
66D-Link DIR-882 User Manual
Section 3 - Conguration
QuickVPN
The QuickVPN feature is a fast and easy way to create a prole for secure remote access to a Local Area Network (LAN). This prole can be used to
congure other devices to connect to your LAN via a secure VPN tunnel. Note that only one account (user name/password) can be created.
From the Features menu, click Quick VPN. Click Advanced Settings to expand the list and see all of the options. To create users to give or remove
VPN access to, click User and refer to page 72.
Enable to allow QuickVPN access to your network.
Enter a username of your choice.
Enter a password of your choice.
Enter a pre-shared key (PSK). The client attempting to connect to
your network through a VPN will need to enter this key.
Select either MSCHAPv2, PAP (Password Authentication Protocol),
or CHAP (Challenge-Handshake Authentication Protocol).
Select either None, RC4-40, or RC4-128 (encryption).
Click Save when you are done.
L2TP over
IPSec:
Username:
Password:
PSK:
Authentication
Protocol:
MPPE:
67D-Link DIR-882 User Manual
Section 3 - Conguration
Management
Time & Schedule
Time
The Time page allows you to congure, update, and maintain the correct time on the DIR-882's internal system clock. The router's internal clock is
used for data logging and schedules.
From the Management menu, click Time & Schedule.
Select your Time Zone from the drop-down menu.
Displays the current date and time.
Enable or disable daylight saving time.
Enable to allow an NTP (Network Time Protocol) server on the Internet
to synchronize the time and date with your router. If you enable this
option, select an NTP server from the drop-down menu. Or, you can
select Manual from the drop-down menu and manually enter the
NTP Server.
Note: To congure the router’s time and date manually, disable the
Update Time Using NTP Server option and use the drop-down menus
that appear to input the time and date.
Click Save when you are done.
Time Zone:
Time:
Enable Daylight
Saving:
Update Time
Using an NTP
Server:
To congure and manage your schedules, click Schedule and refer
to page 68.
68D-Link DIR-882 User Manual
Section 4 - Conguration
Schedule
Create schedules for use with enforcing rules. To create, edit, or delete schedules, from the Time page click Schedule.
When you click on Add Rule, the following screen will appear:
First, enter the Name of your schedule.
Each row represents a day, and each box represents one hour, with the time at the
top of each column. To add a time period to the schedule, simply click on the start
hour and drag to the end hour. You can add multiple days to the schedule, but only
one period per day.
To remove a time period from the schedule, click on the X icon at the end of the row.
Click Apply when you are done.
If you wish to remove a rule, click on its trash icon in the Delete column. If you wish
to edit a rule, click on its pencil icon in the Edit column. If you wish to create a new
rule, click the Add Rule button. Click Save when you are done.
69D-Link DIR-882 User Manual
Section 3 - Conguration
System Log
Click to save a le to your computer. Open using WordPad or similar
program.
Enable to send the router logs to a SysLog Server. If this is disabled,
there will be no other options on this page.
Enter the IP address for the Syslog server. If the Syslog server is
connected to the router, you can select it from the drop-down menu
to automatically populate the eld.
Enable this option if you want the logs to be automatically sent to
an e-mail address. Then enter the settings for your e-mail account.
These can be obtained from your e-mail service provider.
If e-mail notication is enabled, you may also enable this option.
When the log is full, the router will send it by e-mail.
Enable to send an e-mail according to a specied schedule.
If you enable Send on Schedule, use the drop-down menu to select
the schedule that the rule will be enabled on. The schedule may be
set to Always Enable, or you can create your own schedule from the
Schedules section (refer to page 68).
Click Save when you are done.
Check System
Log:
Enable Logging
to Syslog
Server:
Syslog Server IP
Address:
Enable E-mail
Notication:
Send When Log
Full:
Send on
Schedule:
Schedule:
The router keeps a running log of events. The logs can be sent to a Syslog server and delivered to your email address.
From the Management menu, click System Log.
70D-Link DIR-882 User Manual
Section 3 - Conguration
Admin
This page allows you to change the administrator settings, such as change the Admin password and enable remote management.
From the Management menu, click System Admin.
Enter a new Password for the administrator account. You will need to
enter this password whenever you congure the router using a web
browser.
Enables a challenge-response test designed to prevent online hackers
and unauthorized users from gaining access to your router’s network
settings.
Check to enable HTTPS to connect to the router securely. This means
to connect to the router, you must enter https://192.168.0.1 instead
of http://192.168.0.1.
Remote management allows the DIR-882 to be congured from the
Internet by a web browser. A password is still required to access the
web management interface.
The port number used to access the DIR-882 is used in the URL. Example:
http://x.x.x.x:8080 where x.x.x.x is the Internet IP address of the DIR-
882 and 8080 is the port used for the web management interface. If
you enable HTTPS Server, you must enter https:// as part of the URL
to access the router remotely.
Click Save when you are done.
Password:
Enable
Graphical
Authentication
(CAPTCHA):
Enable HTTPS
Server:
Enable Remote
Management:
Remote Admin
Port:
To load, save, or reset the settings, or to reboot the router, click System and refer to page 71.
71D-Link DIR-882 User Manual
Section 3 - Conguration
System
Click Save to save the current router conguration settings to a le on
your computer's hard drive.
Click Select File to locate and load previously saved router conguration
le. This will overwrite the router’s current conguration.
This option will restore all conguration settings back to the settings
that were in eect at the time the router was shipped from the factory.
Any settings that have not been saved will be lost, including any rules
that you have created. If you want to rst save the current router
conguration settings to your computer, use the Save button above.
Click Reboot to reboot the router.
Select a time frame for the router to reboot automatically.
Save Settings
To Local Hard
Drive:
Load Settings
From Local
Hard Drive:
Restore To
Factory Default
Settings:
Reboot The
Device:
Auto Reboot:
This page allows you to save the DIR-882’s current conguration, load a previously saved conguration, and reset the router to the factory default settings.
From the Admin page click System.
72D-Link DIR-882 User Manual
Section 3 - Conguration
User
The Create User page allows you to manage your user accounts. The
current list of user accounts will be displayed, along with their current
permissions for SAMBA and FTP access, as well as VPN status.
If you wish to remove an account, click on its trash can icon in the Delete
column. If you wish to edit an account, click on its pencil icon in the Edit
column. If you wish to create a new account, click the Create User button.
If you edit or create a user, the following options will appear:
Enter a user name.
Create a password.
Click to enable access to le sharing and/or FTP. Select either Read Only
or Read/Write to control whether the user can edit, add, or delete les
on the device. Then choose the parent folder that the user will be able
to access. Files and folders on a higher level will be unavailable. “root”
means that the user can access all les on the device. To change the
selected folder, click Browse and browse to the desired folder.
Enable to give the user Open VPN access.
Click OK to save.
User Name:
Password:
SAMBA/FTP:
VPN:
73D-Link DIR-882 User Manual
Section 3 - Conguration
Device (MAC Filtering)
The Device page will allow you to allow or deny devices based on MAC
address. Select to either an allow list or a block list from the drop-down
menu and then click Add Rule.
Enter a name for the rule.
Manually enter the MAC address of the device or, only if the device is
currently connected to the router and set to DHCP, select the device
from the drop-down menu.
Select a schedule when you want the rule to apply. Click Schedule to
create a new time range.
Click Apply to save.
Name:
MAC Address:
Schedule:
74D-Link DIR-882 User Manual
Section 3 - Conguration
Upgrade
This page will allow you to upgrade the router’s rmware, either automatically or manually. To manually upgrade the rmware, you must rst
download the le from http://support.dlink.com/DIR-882-US.
From the Management menu, click Upgrade.
Displays the Current Firmware Version and Current Firmware Date.
Click Check for New Firmware to prompt the router to check for a new
rmware version. If a newer version is found, you will be prompted to
install it*.
If you prefer to upgrade manually, rst download the rmware le to
your computer that you wish to upgrade to. Next, click the Select File
button and browse to locate the le and install the new rmware.
Firmware
Information:
Check for New
Firmware:
Upgrade
Firmware:
*Note: When you click Check for New Firmware you will see a message
that says, "Checking". If what you have currently installed is the latest version,
you will see a message that says, "This rmware is the latest version".
75D-Link DIR-882 User Manual
Section 3 - Conguration
Statistics
You can view the Internet, LAN, Wi-Fi 2.4GHz, or Wi-Fi 5GHz statistics by clicking
on the respective tabs at the top. The graph will update in real time. To clear the
information on the graph, click Clear.
The trac counter will reset if the device is rebooted.
On the Statistics page you can view the number of packets that pass through the router on the WAN, LAN, and wireless segments.
From the Management menu, click Statistics.
76D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
Connect a Wireless Client to your Router
WPS Button
The easiest and most secure way to connect your wireless devices to the router is with WPS (Wi-Fi Protected Setup). Most wireless
devices such as wireless adapters, media players, Blu-ray DVD players, wireless printers and cameras will have a WPS button (or a
software utility with WPS) that you can press to connect to the DIR-882 router. Refer to your user manual for the wireless device
you want to connect to make sure you understand how to enable WPS. Once you know, follow the steps below:
Step 1 - Press the WPS button on the back of the DIR-882 for about one second. The LED on the front will start to blink.
Step 2 - Within two minutes, press the WPS button on your wireless client (or launch the software utility and start the WPS process).
Step 3 - Allow up to one minute for your connection to be congured. Once the Power LED stops blinking, you will be connected
and your wireless connection will be secure with WPA2.
WPS Button
77D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
Windows® 10
When connecting to the DIR-882 wirelessly for the rst time, you will need to input the wireless network name (SSID) and Wi-Fi
password (security key) of the device you are connecting to. If your product has a Wi-Fi conguration card, you can nd the default
network name and Wi-Fi password here. Otherwise refer to the product label for the default Wi-Fi network SSID and password,
or enter the Wi-Fi credentials set during the product conguration.
To join an existing network, click the wireless network icon in the taskbar,
next to the time display.
A list of wireless networks which are within range of your computer will
appear. Select the desired network by clicking on the SSID.
Wireless Icon
78D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
To connect to the SSID, click Connect.
To automatically connect with the router when your device next detects
the SSID, click the Connect Automatically check box.
You will then be prompted to enter the Wi-Fi password (network security
key) for the wireless network. Enter the password into the box and click
Next to connect to the network. Your computer will now automatically
connect to this wireless network when it is detected.
You can also use Wi-Fi Protected Setup (WPS) to connect to the router.
Press the WPS button on your D-Link device and you will be automatically
connected.
79D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
Windows® 8
It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before conguring
your wireless adapter. If you are joining an existing network, you will need to know the security key (Wi-Fi password) being used.
To join an existing network, locate the wireless network icon in the
taskbar next to the time display.
Wireless Icon
Clicking on this icon will display a list of wireless networks that are within
connecting proximity of your computer. Select the desired network by
clicking on the network name.
80D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
You will then be prompted to enter the network security key (Wi-Fi
password) for the wireless network. Enter the password into the box
and click Next.
If you wish to use Wi-Fi Protected Setup (WPS) to connect to the router,
you can also press the WPS button on your router during this step to
enable the WPS function.
When you have established a successful connection to a wireless network,
the word Connected will appear next to the name of the network to
which you are connected to.
81D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
Windows® 7
It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before conguring
your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
1. Click on the wireless icon in your system tray (lower-right corner).
2. The utility will display any available wireless networks in your area.
Wireless Icon
WPA/WPA2
82D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
3. Highlight the wireless connection with Wi-Fi name (SSID) you would
like to connect to and click the Connect button.
If you get a good signal but cannot access the Internet, check your TCP/
IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
4. The following window appears while your computer tries to connect
to the router.
83D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
5. Enter the same security key or passphrase (Wi-Fi password) that is on
your router and click Connect. You can also connect by pushing the
WPS button on the router.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as the one on the wireless
router.
84D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
WPS
The WPS feature of the DIR-882 can be congured using Windows® 7. Carry out the following steps to use Windows® 7 to
congure the WPS feature:
1. Click the Start button and select Computer from the Start menu.
2. Click Network on the left side.
85D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
3. Double-click the DIR-882.
4. Input the WPS PIN number (on the router label) in the Setup > Wireless
Setup menu in the Router’s Web UI) and click Next.
86D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
5. Type a name to identify the network.
6. To congure advanced settings, click the icon.
Click Next to continue.
87D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
7. The following window appears while the Router is being congured.
Wait for the conguration to complete.
8. The following window informs you that WPS on the router has been
set up successfully.
Make a note of the security key as you may need to provide this security
key if adding an older wireless device to the network in the future.
9. Click Close to complete WPS setup.
88D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
Windows Vista®
Windows Vista® users may use the built-in wireless utility. If you are using another company’s wireless utility, please refer to the
user manual of your wireless adapter for help connecting to a wireless network. Most wireless utilities will have a “site survey”
option similar to the Windows Vista® utility as seen below.
Right-click on the wireless computer icon in your system tray (lower-right
corner next to the time). Select Connect to a network.
If you receive the Wireless Networks Detected bubble, click on the
center of the bubble to access the utility.
or
The utility will display any available wireless networks in your area. Click
on a network (displayed using the SSID) and click the Connect button.
If you get a good signal but cannot access the Internet, check you
TCP/IP settings for your wireless adapter. Refer to the Networking Basics
section in this manual for more information.
89D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
WPA/WPA2
It is recommended that you enable wireless security (WPA/WPA2) on your wireless router or access point before conguring
your wireless adapter. If you are joining an existing network, you will need to know the security key or passphrase being used.
2. Highlight the Wi-Fi name (SSID) you would like to connect to and
click Connect.
1. Open the Windows Vista® Wireless Utility by right-clicking on the
wireless computer icon in your system tray (lower right corner of
screen). Select Connect to a network.
90D-Link DIR-882 User Manual
Section 5 - Connecting to a Wireless Network
3. Enter the same security key or passphrase (Wi-Fi password) that is on
your router and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the security settings are correct. The
key or passphrase must be exactly the same as the one on the wireless
router.
91D-Link DIR-882 User Manual
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that may occur during the installation and operation of the DIR-882.
1. Why can’t I access the web-based conguration utility?
When entering the IP address of the D-Link router (192.168.0.1 for example), you are not connecting to a website, nor do you
have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device itself. Your computer must
be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
- Explorer® 11 or higher
- Firefox®
- Chrome™
- Safari® 7 or higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using a
dierent cable or connecting to a dierent port on the device. If the computer is turned o, the link light may not be on.
• Disable any Internet security software running on the computer. Software rewalls such as Zone Alarm, Black Ice, Sygate,
and Norton Personal Firewall may block access to the conguration pages. Check the help les included with your rewall
software for more information on disabling or conguring it.
• Congure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab, click
the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings button.
Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three times.
• Close your web browser (if open) and open it.
92D-Link DIR-882 User Manual
Section 6 - Troubleshooting
• Access the web management. Open your web browser and enter the IP address of your D-Link router in the address bar. This
should open the login page for your web management.
• If you still cannot access the conguration, unplug the power to the router for 10 seconds and plug back in. Wait about 30
seconds and try accessing the conguration. If you have multiple computers, try connecting using a dierent computer.
2. How do I connect my wireless devices to the DIR-882 router?
1. Open your wireless network utility that displays available wireless networks.
2. Select the Wi-Fi Network name you assigned during the Setup Wizard and connect.
Note: If you did not run the Setup Wizard or you reset the router to its default settings, refer to the Wi-Fi Conguration Card included
for the default Wi-Fi Network Name and Wi-Fi Password.
You can also connect wireless devices to the DIR-882 router using WPS:
1. Press the WPS button on the DIR-882 for a minimum of three seconds, or until the Power LED starts to blink green.
2. Within one minute press the WPS button on your wireless device.
3. Allow up to two minutes to connect.
Note: Some devices may require you to log in to a utility to start the WPS process. Refer to the user manual for the device you want to
connect to the router if you do not know how to start the WPS process.
3. What can I do if I forget my password?
If you forget your password, you must reset your router. Unfortunately, this process will change all your settings back to the
factory defaults.
To reset the router, locate the reset button (hole) on the back of the unit. With the router powered on, use an unfolded paper
clip to press and hold the button down for about 10 seconds. Release the button and the router will go through its reboot
process. Wait about 30 seconds to access the router.
93D-Link DIR-882 User Manual
Section 6 - Troubleshooting
5. Why can’t I connect to certain sites or send and receive e-mails when connecting through my router?
If you are having a problem sending or receiving e-mail, or connecting to secure sites such as eBay and banking sites, we
suggest lowering the MTU in increments of ten (e.g., 1492, 1482, 1472, etc).
To nd the proper MTU Size, you’ll have to do a special ping of the destination you’re trying to go to. A destination could be
another computer, or a URL.
• Click on Start and then click Run.
• Windows® 8, 7, and Vista® users type in cmd and press
Enter (or click OK).
• Once the window opens, you’ll need to do a special ping.
Use the following syntax:
ping [url] [-f] [-l] [MTU value]
Example: ping yahoo.com -f -l 1472
4. Can I connect the DIR-882 to an existing router?
We recommend that you replace your existing router with the DIR-882 instead of using both. If your modem is a combo router,
you may want to contact your ISP or review the manufacturer's user guide so you can put the combo router into Bridge mode,
which will turn o the device's NAT functions.
94D-Link DIR-882 User Manual
Section 6 - Troubleshooting
You should start at 1472 and work your way down by 10 each time. Once you get a reply, go up by 2 until you get a fragmented
packet. Take that value and add 28 to the value to account for the various TCP/IP headers. For example, lets say that 1452 was the
proper value, the actual MTU size would be 1480, which is the optimum for the network we’re working with (1452+28=1480).
Once you nd your MTU, you can now congure your router with the proper MTU size.
To change the MTU rate on your router follow the steps below:
• Open your browser, enter the IP address of your router (192.168.0.1) and click OK.
• Enter your username (admin) and password (blank by default). Click OK to enter the web conguration page
for the device.
• Click on Setup and then click Manual Congure.
• To change the MTU, enter the number in the MTU eld and click Save Settings to save your settings.
• Test your e-mail. If changing the MTU does not resolve the problem, continue changing the MTU in increments
of ten.
95D-Link DIR-882 User Manual
Appendix A - Wireless Basics
D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless
connectivity within your home, business, or public access wireless networks. Strictly adhering to the IEEE standard, the D-Link
wireless family of products will allow you to securely access the data you want, when, and where you want it. You will be able
to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals instead
of wires. Wireless LANs are used increasingly in both home and oce environments, and public areas such as airports, coee
shops and universities. Innovative ways to utilize WLAN technology are helping people work, and communicate more eciently.
Increased mobility and the absence of cabling and other xed infrastructure have proven to be benecial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop and desktop
systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in order to
use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device used to provide
this link.
Wireless Basics
96D-Link DIR-882 User Manual
Appendix A - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi uses radio
frequency to connect wirelessly so you have the freedom to connect computers anywhere in your home or oce network.
Why D-Link Wireless?
D-Link is the worldwide leader and award winning designer, developer, and manufacturer of networking products. D-Link
delivers the performance you need at a price you can aord. D-Link has all the products you need to build your network.
How does wireless work?
Wireless works similarly to how cordless phones work, through radio signals that transmit data from one point A to point B.
But wireless technology has restrictions as to how you can access the network. You must be within the wireless network range
area to be able to connect your computer. There are two dierent types of wireless networks: Wireless Local Area Network
(WLAN), and Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a wireless local area network, a device called an Access Point (AP) connects computers to the network. The access point
has a small antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor access
point the signal can travel up to 300 feet. With an outdoor access point the signal can reach out up to 30 miles to serve places
like manufacturing plants, industrial locations, university and high school campuses, airports, golf courses, and many other
outdoor venues.
97D-Link DIR-882 User Manual
Appendix A - Wireless Basics
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPAN. Bluetooth devices in WPAN operate in a range up to
30 feet away.
Compared to WLAN the speed and wireless operation range are both less than WLAN, but in return it doesn’t use nearly as
much power. This makes it ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and other
devices that operate on batteries.
Who uses wireless?
Wireless technology as become so popular in recent years that almost everyone is using it, whether it’s for home, oce, business,
D-Link has a wireless solution for it.
Home Uses/Benets
• Gives everyone at home broadband access
• Surf the web, check email, instant message, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Oce and Home Oce Uses/Benets
• Stay on top of everything at home as you would at oce
• Remotely access your oce network from home
• Share Internet connection and printer with multiple computers
• No need to dedicate oce space
98D-Link DIR-882 User Manual
Appendix A - Wireless Basics
Where is wireless used?
Wireless technology is expanding everywhere, not just at home or oce. People like the freedom of mobility and it’s becoming
so popular that more and more public facilities now provide wireless access to attract people. The wireless connection in public
places is usually called “hotspots”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to the Internet from remote locations
like: Airports, Hotels, Coee Shops, Libraries, Restaurants, and Convention Centers.
Wireless network is easy to setup, but if you’re installing it for the rst time it could be quite a task not knowing where to start.
That’s why we’ve put together a few setup steps and tips to help you through the process of setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your router or Access Point
Make sure you place the router/access point in a centralized location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If you have
a two-story home, you may need a repeater to boost the signal to extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the router/access
point. This would signicantly reduce any interference that the appliances might cause since they operate on same frequency.
99D-Link DIR-882 User Manual
Appendix A - Wireless Basics
Security
Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on
the WPA or WEP security feature on the router. Refer to the product manual for detail information on how to set it up.
There are basically two modes of networking:
• Infrastructure – All wireless clients will connect to an access point or wireless router.
• Ad-Hoc – Directly connecting to another computer for peer-to-peer communication using wireless network
adapters on each computer, such as two or more DIR-869 wireless network Cardbus adapters.
An Infrastructure network contains an Access Point or wireless router. All the wireless devices, or clients, will connect to the
wireless router or access point.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in Ad-Hoc
mode to communicate.
Wireless Modes
100D-Link DIR-882 User Manual
Appendix B - Networking Basics
Networking Basics
Check your IP address
By default, the TCP/IP settings should be set to obtain an IP address from a DHCP server (i.e., wireless router) automatically. To
verify your IP address, please follow the steps below.
Click on Start button in the lower left corner of the screen, or press the Windows button on your keyboard. In the Search eld,
type cmd and press Enter.
At the prompt, type ipcong and press Enter.
This will display the IP address, subnet mask, and the
default gateway of your adapter.
If the address is 0.0.0.0, check your adapter installation,
security settings, and the settings on your router.
Some rewall software programs may block a DHCP
request on newly installed adapters.
101D-Link DIR-882 User Manual
Appendix B - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:
Step 1
Windows® 8 - Press the Windows key and then type IP. Click Settings on the right side and then click View Network Connections.
Windows® 7 - Click on Start > Control Panel > Network and Internet > Network and Sharing Center.
Windows Vista® - Click on Start > Control Panel > Network and Internet > Network and Sharing Center > Manage Network
Connections.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet
as your network or the LAN IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address 192.168.0.X
where X is a number between 2 and 99. Make sure that the number you choose is not
in use on the network. Set the Default Gateway the same as the LAN IP address of your
router (i.e., 192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
102D-Link DIR-882 User Manual
Appendix B - Networking Basics
Wireless Security
This section will show you the dierent levels of security you can use to protect your data from intruders. The DIR-869 oers the following
types of security:
• WPA2 (Wi-Fi Protected Access 2) • WPA2-PSK (Pre-Shared Key)
• WPA (Wi-Fi Protected Access) • WPA-PSK (Pre-Shared Key)
What is WPA?
WPA (Wi-Fi Protected Access), is a Wi-Fi standard that was designed to improve the security features of WEP (Wired Equivalent Privacy).
The 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys using a hashing
algorithm and by adding an integrity-checking feature, ensures that the keys haven’t been tampered with. WPA2 is based
on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP.
• User authentication, which is generally missing in WEP, through the extensible authentication protocol (EAP). WEP
regulates access to a wireless network based on a computer’s hardware-specic MAC address, which is relatively simple
to be snied out and stolen. EAP is built on a more secure public-key encryption system to ensure that only authorized
network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric password between
8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must be the exact same key entered on your
wireless router or access point.
WPA/WPA2 incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP is built on a more secure public
key encryption system to ensure that only authorized network users can access the network.
103D-Link DIR-882 User Manual
Appendix C - Technical Specications
Technical Specications
Device Interfaces
• Four 10/100/1000 Mbps Gigabit Ethernet ports (LAN)
• One 10/100/1000 Mbps Gigabit Ethernet port (INTERNET)
• WPS (Wi-Fi Protected Setup) Push Button
• Reset Button
• USB 2.0 Port
• USB 3.0 Port
Standards
• IEEE 802.11ac
• IEEE 802.11n
• IEEE 802.11g
• IEEE 802.11a
• IEEE 802.3ab
• IEEE 802.3u
Security
• Wi-Fi Protected Access (WPA/WPA2)
• WPS PIN/PBC (Wi-Fi Protected Setup)
Power
• Input: 100 to 240 V AC, 50/60 Hz
• Output: 12 V, 1.5 A
Temperature
• Operating: 32 to 104°F
• Storage: -4 to 149°F
Humidity
• 10% to 90% non-condensing (Operating)
• 5% to 95% non-condensing (Storage)
Certications
• FCC Class B
• IPv6 Ready
• Wi-Fi Certied
Dimensions
• 10 x 7 x 1.75 inches
Warranty
•1-Year Limited Warranty
Maximum wireless signal rate derived from IEEE Standard 802.11ac, 802.11g, and 802.11n specications. Actual data throughput will vary. Network conditions and environmental factors, including
volume of network trac, building materials and construction, and network overhead, lower actual data throughput rate. Environmental factors will adversely aect wireless signal range.
104D-Link DIR-882 User Manual
Appendix D - Contacting Technical Support
Contacting Technical Support
U.S. and Canadian customers can contact D-Link technical support through our web site or by phone.
Before you contact technical support, please have the following ready:
• Model number of the product (e.g., DIR-882-US)
• Hardware Revision (located on the label on the bottom of the router [e.g., rev A1])
• Serial Number (s/n number located on the label on the bottom of the router).
You can nd software updates and user documentation on the D-Link website as well as frequently asked questions and
answers to technical issues.
For customers within the United States:
Phone Support:
(877) 453-5465
Internet Support:
http://support.dlink.com
For customers within Canada:
Phone Support:
(800) 361-5265
Internet Support:
http://support.dlink.ca
105D-Link DIR-882 User Manual
Appendix E - GNU General Public License
GPL Code Statement
This D-Link product includes software code developed by third parties, including software code subject to the GNU General Public License (“GPL”)
or GNU Lesser General Public License (“LGPL”). As applicable, the terms of the GPL and LGPL, and information on obtaining access to the GPL
code and LGPL code used in this product, are available to you at:
http://tsd.dlink.com.tw/GPL.asp
The GPL code and LGPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more
authors. For details, see the GPL code and the LGPL code for this product and the terms of the GPL and LGPL.
WRITTEN OFFER FOR GPL AND LGPL SOURCE CODE
Where such specic license terms entitle you to the source code of such software, D-Link will provide upon written request via email and/or
traditional paper mail the applicable GPL and LGPLsource code files via CD-ROM for a nominal cost to cover shipping and media charges as
allowed under the GPL and LGPL.
Please direct all inquiries to:
Email: GPLCODE@DLink.com
Snail Mail:
Attn: GPLSOURCE REQUEST
D-Link Systems, Inc.
17595 Mt. Herrmann Street
Fountain Valley, CA 92708
GNU GENERAL PUBLIC LICENSE
Version 3, 29 June 2007
Copyright (C) 2007 Free Software Foundation, Inc. <http://fsf.org/> Everyone is permitted to copy and distribute verbatim copies of this license
document, but changing it is not allowed.
106D-Link DIR-882 User Manual
Appendix E - GNU General Public License
Preamble
The GNU General Public License is a free, copyleft license for software and other kinds of works.
The licenses for most software and other practical works are designed to take away your freedom to share and change the works. By contrast, the
GNU General Public License is intended to guarantee your freedom to share and change all versions of a program--to make sure it remains free
software for all its users. We, the Free Software Foundation, use the GNU General Public License for most of our software; it applies also to any other
work released this way by its authors. You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the
freedom to distribute copies of free software (and charge for them if you wish), that you receive source code or can get it if you want it, that you
can change the software or use pieces of it in new free programs, and that you know you can do these things.
To protect your rights, we need to prevent others from denying you these rights or asking you to surrender the rights. Therefore, you have certain
responsibilities if you distribute copies of the software, or if you modify it: responsibilities to respect the freedom of others.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must pass on to the recipients the same freedoms that you
received. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
Developers that use the GNU GPL protect your rights with two steps:
(1) assert copyright on the software, and (2) oer you this License giving you legal permission to copy, distribute and/or modify it.
For the developers’ and authors’ protection, the GPL clearly explains that there is no warranty for this free software. For both users’ and authors’
sake, the GPL requires that modied versions be marked as changed, so that their problems will not be attributed erroneously to authors of
previous versions.
Some devices are designed to deny users access to install or run modied versions of the software inside them, although the manufacturer can
do so. This is fundamentally incompatible with the aim of protecting users’ freedom to change the software. The systematic pattern of such abuse
occurs in the area of products for individuals to use, which is precisely where it is most unacceptable. Therefore, we have designed this version of
the GPL to prohibit the practice for those products. If such problems arise substantially in other domains, we stand ready to extend this provision
to those domains in future versions of the GPL, as needed to protect the freedom of users.
Finally, every program is threatened constantly by software patents. States should not allow patents to restrict development and use of software
on general-purpose computers, but in those that do, we wish to avoid the special danger that patents applied to a free program could make it
eectively proprietary. To prevent this, the GPL assures that patents cannot be used to render the program non-free.
The precise terms and conditions for copying, distribution and modication follow.
107D-Link DIR-882 User Manual
Appendix E - GNU General Public License
TERMS AND CONDITIONS
0. Denitions.
“This License” refers to version 3 of the GNU General Public License.
“Copyright” also means copyright-like laws that apply to other kinds of works, such as semiconductor masks.
“The Program” refers to any copyrightable work licensed under this License. Each licensee is addressed as “you”. “Licensees” and “recipients” may
be individuals or organizations.
To “modify” a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an
exact copy. The resulting work is called a “modied version” of the earlier work or a work “based on” the earlier work.
A “covered work” means either the unmodied Program or a work based on the Program.
To “propagate” a work means to do anything with it that, without permission, would make you directly or secondarily liable for infringement under
applicable copyright law, except executing it on a computer or modifying a private copy. Propagation includes copying, distribution (with or
without modication), making available to the public, and in some countries other activities as well.
To “convey” a work means any kind of propagation that enables other parties to make or receive copies. Mere interaction with a user through a
computer network, with no transfer of a copy, is not conveying.
An interactive user interface displays “Appropriate Legal Notices” to the extent that it includes a convenient and prominently visible feature that
(1) displays an appropriate copyright notice, and (2) tells the user that there is no warranty for the work (except to the extent that warranties are
provided), that licensees may convey the work under this License, and how to view a copy of this License. If the interface presents a list of user
commands or options, such as a menu, a prominent item in the list meets this criterion.
1. Source Code.
The “source code” for a work means the preferred form of the work for making modications to it. “Object code” means any non-source form of a
work.
A “Standard Interface” means an interface that either is an ocial standard dened by a recognized standards body, or, in the case of interfaces
specied for a particular programming language, one that is widely used among developers working in that language.
108D-Link DIR-882 User Manual
Appendix E - GNU General Public License
The “System Libraries” of an executable work include anything, other than the work as a whole, that (a) is included in the normal form of packaging
a Major Component, but which is not part of that Major Component, and (b) serves only to enable use of the work with that Major Component,
or to implement a Standard Interface for which an implementation is available to the public in source code form. A “Major Component”, in this
context, means a major essential component (kernel, window system, and so on) of the specic operating system (if any) on which the executable
work runs, or a compiler used to produce the work, or an object code interpreter used to run it.
The “Corresponding Source” for a work in object code form means all the source code needed to generate, install, and (for an executable work)
run the object code and to modify the work, including scripts to control those activities. However, it does not include the work’s System Libraries,
or general-purpose tools or generally available free programs which are used unmodied in performing those activities but which are not part of
the work. For example, Corresponding Source includes interface denition les associated with source les for the work, and the source code for
shared libraries and dynamically linked subprograms that the work is specically designed to require, such as by intimate data communication or
control ow between those subprograms and other parts of the work.
The Corresponding Source need not include anything that users can regenerate automatically from other parts of the Corresponding Source.
The Corresponding Source for a work in source code form is that same work.
2. Basic Permissions.
All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions
are met. This License explicitly arms your unlimited permission to run the unmodied Program. The output from running a covered work is
covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other
equivalent, as provided by copyright law.
You may make, run and propagate covered works that you do not convey, without conditions so long as your license otherwise remains in force.
You may convey covered works to others for the sole purpose of having them make modications exclusively for you, or provide you with facilities
for running those works, provided that you comply with the terms of this License in conveying all material for which you do not control copyright.
Those thus making or running the covered works for you must do so exclusively on your behalf, under your direction and control, on terms that
prohibit them from making any copies of your copyrighted material outside their relationship with you.
Conveying under any other circumstances is permitted solely under the conditions stated below. Sublicensing is not allowed; section 10 makes it
unnecessary.
109D-Link DIR-882 User Manual
Appendix E - GNU General Public License
3. Protecting Users’ Legal Rights From Anti-Circumvention Law.
No covered work shall be deemed part of an eective technological measure under any applicable law fullling obligations under article 11 of the
WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures.
When you convey a covered work, you waive any legal power to forbid circumvention of technological measures to the extent such circumvention
is eected by exercising rights under this License with respect to the covered work, and you disclaim any intention to limit operation or modication
of the work as a means of enforcing, against the work’s users, your or third parties’ legal rights to forbid circumvention of technological measures.
4. Conveying Verbatim Copies.
You may convey verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice; keep intact all notices stating that this License and any non-permissive terms added in
accord with section 7 apply to the code; keep intact all notices of the absence of any warranty; and give all recipients a copy of this License along
with the Program.
You may charge any price or no price for each copy that you convey, and you may oer support or warranty protection for a fee.
5. Conveying Modied Source Versions.
You may convey a work based on the Program, or the modications to produce it from the Program, in the form of source code under the terms of
section 4, provided that you also meet all of these conditions:
a) The work must carry prominent notices stating that you modied it, and giving a relevant date.
b) The work must carry prominent notices stating that it is released under this License and any conditions added under section 7.
This requirement modies the requirement in section 4 to “keep intact all notices”.
c) You must license the entire work, as a whole, under this License to anyone who comes into possession of a copy. This License
will therefore apply, along with any applicable section 7 additional terms, to the whole of the work, and all its parts, regardless
of how they are packaged. This License gives no permission to license the work in any other way, but it does not invalidate such
permission if you have separately received it.
d) If the work has interactive user interfaces, each must display Appropriate Legal Notices; however, if the Program has interactive
interfaces that do not display Appropriate Legal Notices, your work need not make them do so.
110D-Link DIR-882 User Manual
Appendix E - GNU General Public License
A compilation of a covered work with other separate and independent works, which are not by their nature extensions of the covered work, and
which are not combined with it such as to form a larger program, in or on a volume of a storage or distribution medium, is called an “aggregate”
if the compilation and its resulting copyright are not used to limit the access or legal rights of the compilation’s users beyond what the individual
works permit. Inclusion of a covered work in an aggregate does not cause this License to apply to the other parts of the aggregate.
6. Conveying Non-Source Forms.
You may convey a covered work in object code form under the terms of sections 4 and 5, provided that you also convey the machine-readable
Corresponding Source under the terms of this License, in one of these ways:
a) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by the
Corresponding Source xed on a durable physical medium customarily used for software interchange.
b) Convey the object code in, or embodied in, a physical product (including a physical distribution medium), accompanied by a
written oer, valid for at least three years and valid for as long as you oer spare parts or customer support for that product
model, to give anyone who possesses the object code either (1) a copy of the Corresponding Source for all the software in the
product that is covered by this License, on a durable physical medium customarily used for software interchange, for a price no
more than your reasonable cost of physically performing this conveying of source, or (2) access to copy the Corresponding Source
from a network server at no charge.
c) Convey individual copies of the object code with a copy of the written oer to provide the Corresponding Source. This alternative
is allowed only occasionally and non-commercially, and only if you received the object code with such an oer, in accord with
subsection 6b.
d) Convey the object code by oering access from a designated place (gratis or for a charge), and oer equivalent access to the
Corresponding Source in the same way through the same place at no further charge. You need not require recipients to copy the
Corresponding Source along with the object code. If the place to copy the object code is a network server, the Corresponding
Source may be on a dierent server (operated by you or a third party) that supports equivalent copying facilities, provided you
maintain clear directions next to the object code saying where to nd the Corresponding Source. Regardless of what server hosts
the Corresponding Source, you remain obligated to ensure that it is available for as long as needed to satisfy these requirements.
e) Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and
Corresponding Source of the work are being oered to the general public at no charge under subsection 6d.
A separable portion of the object code, whose source code is excluded from the Corresponding Source as a System Library, need not be
included in conveying the object code work.
111D-Link DIR-882 User Manual
Appendix E - GNU General Public License
A “User Product” is either (1) a “consumer product”, which means any tangible personal property which is normally used for personal, family, or
household purposes, or (2) anything designed or sold for incorporation into a dwelling. In determining whether a product is a consumer product,
doubtful cases shall be resolved in favor of coverage. For a particular product received by a particular user, “normally used” refers to a typical
or common use of that class of product, regardless of the status of the particular user or of the way in which the particular user actually uses,
or expects or is expected to use, the product. A product is a consumer product regardless of whether the product has substantial commercial,
industrial or non-consumer uses, unless such uses represent the only signicant mode of use of the product.
“Installation Information” for a User Product means any methods, procedures, authorization keys, or other information required to install and
execute modied versions of a covered work in that User Product from a modied version of its Corresponding Source. The information must
suce to ensure that the continued functioning of the modied object code is in no case prevented or interfered with solely because modication
has been made.
If you convey an object code work under this section in, or with, or specically for use in, a User Product, and the conveying occurs as part of a
transaction in which the right of possession and use of the User Product is transferred to the recipient in perpetuity or for a xed term (regardless of
how the transaction is characterized), the Corresponding Source conveyed under this section must be accompanied by the Installation Information.
But this requirement does not apply if neither you nor any third party retains the ability to install modied object code on the User Product (for
example, the work has been installed in ROM).
The requirement to provide Installation Information does not include a requirement to continue to provide support service, warranty, or updates
for a work that has been modied or installed by the recipient, or for the User Product in which it has been modied or installed. Access to a
network may be denied when the modication itself materially and adversely aects the operation of the network or violates the rules and
protocols for communication across the network.
Corresponding Source conveyed, and Installation Information provided, in accord with this section must be in a format that is publicly documented
(and with an implementation available to the public in source code form), and must require no special password or key for unpacking, reading or
copying.
7. Additional Terms.
“Additional permissions” are terms that supplement the terms of this License by making exceptions from one or more of its conditions. Additional
permissions that are applicable to the entire Program shall be treated as though they were included in this License, to the extent that they are valid
under applicable law. If additional permissions apply only to part of the Program, that part may be used separately under those permissions, but
the entire Program remains governed by this License without regard to the additional permissions.
112D-Link DIR-882 User Manual
Appendix E - GNU General Public License
When you convey a copy of a covered work, you may at your option remove any additional permissions from that copy, or from any part of it.
(Additional permissions may be written to require their own removal in certain cases when you modify the work). You may place additional
permissions on material, added by you to a covered work, for which you have or can give appropriate copyright permission.
Notwithstanding any other provision of this License, for material you add to a covered work, you may (if authorized by the copyright holders of
that material) supplement the terms of this License with terms:
a) Disclaiming warranty or limiting liability dierently from the terms of sections 15 and 16 of this License; or
b) Requiring preservation of specied reasonable legal notices or author attributions in that material or in the Appropriate Legal
Notices displayed by works containing it; or
c) Prohibiting misrepresentation of the origin of that material, or requiring that modied versions of such material be marked in
reasonable ways as dierent from the original version; or
d) Limiting the use for publicity purposes of names of licensors or authors of the material; or
e) Declining to grant rights under trademark law for use of some trade names, trademarks, or service marks; or
f) Requiring indemnication of licensors and authors of that material by anyone who conveys the material (or modied versions of
it) with contractual assumptions of liability to the recipient, for any liability that these contractual assumptions directly impose
on those licensors and authors.
All other non-permissive additional terms are considered “further restrictions” within the meaning of section 10. If the Program as you received
it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further restriction, you may remove that
term. If a license document contains a further restriction but permits relicensing or conveying under this License, you may add to a covered work
material governed by the terms of that license document, provided that the further restriction does not survive such relicensing or conveying.
If you add terms to a covered work in accord with this section, you must place, in the relevant source les, a statement of the additional terms that
apply to those les, or a notice indicating where to nd the applicable terms.
Additional terms, permissive or non-permissive, may be stated in the form of a separately written license, or stated as exceptions; the above
requirements apply either way.
113D-Link DIR-882 User Manual
Appendix E - GNU General Public License
8. Termination.
You may not propagate or modify a covered work except as expressly provided under this License. Any attempt otherwise to propagate or modify
it is void, and will automatically terminate your rights under this License (including any patent licenses granted under the third paragraph of
section 11).
However, if you cease all violation of this License, then your license from a particular copyright holder is reinstated (a) provisionally, unless and until
the copyright holder explicitly and nally terminates your license, and (b) permanently, if the copyright holder fails to notify you of the violation
by some reasonable means prior to 60 days after the cessation.
Moreover, your license from a particular copyright holder is reinstated permanently if the copyright holder noties you of the violation by some
reasonable means, this is the rst time you have received notice of violation of this License (for any work) from that copyright holder, and you cure
the violation prior to 30 days after your receipt of the notice.
Termination of your rights under this section does not terminate the licenses of parties who have received copies or rights from you under this
License. If your rights have been terminated and not permanently reinstated, you do not qualify to receive new licenses for the same material
under section 10.
9. Acceptance Not Required for Having Copies.
You are not required to accept this License in order to receive or run a copy of the Program. Ancillary propagation of a covered work occurring
solely as a consequence of using peer-to-peer transmission to receive a copy likewise does not require acceptance. However, nothing other than
this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do not accept this License.
Therefore, by modifying or propagating a covered work, you indicate your acceptance of this License to do so.
10. Automatic Licensing of Downstream Recipients.
Each time you convey a covered work, the recipient automatically receives a license from the original licensors, to run, modify and propagate that
work, subject to this License. You are not responsible for enforcing compliance by third parties with this License.
An “entity transaction” is a transaction transferring control of an organization, or substantially all assets of one, or subdividing an organization, or
merging organizations. If propagation of a covered work results from an entity transaction, each party to that transaction who receives a copy of
the work also receives whatever licenses to the work the party’s predecessor in interest had or could give under the previous paragraph, plus a
right to possession of the Corresponding Source of the work from the predecessor in interest, if the predecessor has it or can get it with reasonable
eorts.
114D-Link DIR-882 User Manual
Appendix E - GNU General Public License
You may not impose any further restrictions on the exercise of the rights granted or armed under this License. For example, you may not impose
a license fee, royalty, or other charge for exercise of rights granted under this License, and you may not initiate litigation (including a cross-claim
or counterclaim in a lawsuit) alleging that any patent claim is infringed by making, using, selling, oering for sale, or importing the Program or any
portion of it.
11. Patents.
A “contributor” is a copyright holder who authorizes use under this License of the Program or a work on which the Program is based. The work thus
licensed is called the contributor’s “contributor version”.
A contributor’s “essential patent claims” are all patent claims owned or controlled by the contributor, whether already acquired or hereafter acquired,
that would be infringed by some manner, permitted by this License, of making, using, or selling its contributor version, but do not include claims
that would be infringed only as a consequence of further modication of the contributor version. For purposes of this denition, “control” includes
the right to grant patent sublicenses in a manner consistent with the requirements of this License.
Each contributor grants you a non-exclusive, worldwide, royalty-free patent license under the contributor’s essential patent claims, to make, use,
sell, oer for sale, import and otherwise run, modify and propagate the contents of its contributor version.
In the following three paragraphs, a “patent license” is any express agreement or commitment, however denominated, not to enforce a patent
(such as an express permission to practice a patent or covenant not to sue for patent infringement). To “grant” such a patent license to a party
means to make such an agreement or commitment not to enforce a patent against the party.
If you convey a covered work, knowingly relying on a patent license, and the Corresponding Source of the work is not available for anyone to
copy, free of charge and under the terms of this License, through a publicly available network server or other readily accessible means, then you
must either (1) cause the Corresponding Source to be so available, or (2) arrange to deprive yourself of the benet of the patent license for this
particular work, or (3) arrange, in a manner consistent with the requirements of this License, to extend the patent license to downstream recipients.
“Knowingly relying” means you have actual knowledge that, but for the patent license, your conveying the covered work in a country, or your
recipient’s use of the covered work in a country, would infringe one or more identiable patents in that country that you have reason to believe
are valid.
If, pursuant to or in connection with a single transaction or arrangement, you convey, or propagate by procuring conveyance of, a covered work,
and grant a patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specic copy
of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
115D-Link DIR-882 User Manual
Appendix E - GNU General Public License
A patent license is “discriminatory” if it does not include within the scope of its coverage, prohibits the exercise of, or is conditioned on the non-
exercise of one or more of the rights that are specically granted under this License. You may not convey a covered work if you are a party to an
arrangement with a third party that is in the business of distributing software, under which you make payment to the third party based on the
extent of your activity of conveying the work, and under which the third party grants, to any of the parties who would receive the covered work
from you, a discriminatory patent license (a) in connection with copies of the covered work conveyed by you (or copies made from those copies), or
(b) primarily for and in connection with specic products or compilations that contain the covered work, unless you entered into that arrangement,
or that patent license was granted, prior to 28 March 2007.
Nothing in this License shall be construed as excluding or limiting any implied license or other defenses to infringement that may otherwise be
available to you under applicable patent law.
12. No Surrender of Others’ Freedom.
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you cannot convey a covered work so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not convey it at all. For example, if you agree to terms that obligate
you to collect a royalty for further conveying from those to whom you convey the Program, the only way you could satisfy both those terms and
this License would be to refrain entirely from conveying the Program.
13. Use with the GNU Aero General Public License.
Notwithstanding any other provision of this License, you have permission to link or combine any covered work with a work licensed under version
3 of the GNU Aero General Public License into a single combined work, and to convey the resulting work. The terms of this License will continue
to apply to the part which is the covered work, but the special requirements of the GNU Aero General Public License, section 13, concerning
interaction through a network will apply to the combination as such.
14. Revised Versions of this License.
The Free Software Foundation may publish revised and/or new versions of the GNU General Public License from time to time. Such new versions
will be similar in spirit to the present version, but may dier in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program species that a certain numbered version of the GNU General Public License
“or any later version” applies to it, you have the option of following the terms and conditions either of that numbered version or of any later version
published by the Free Software Foundation. If the Program does not specify a version number of the GNU General Public License, you may choose
any version ever published by the Free Software Foundation. If the Program species that a proxy can decide which future versions of the GNU
General Public License can be used, that proxy’s public statement of acceptance of a version permanently authorizes you to choose that version
for the Program.
116D-Link DIR-882 User Manual
Appendix E - GNU General Public License
Later license versions may give you additional or dierent permissions. However, no additional obligations are imposed on any author or copyright
holder as a result of your choosing to follow a later version.
15. Disclaimer of Warranty.
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
16. Limitation of Liability.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MODIFIES AND/OR CONVEYS THE PROGRAM AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO
OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
17. Interpretation of Sections 15 and 16.
If the disclaimer of warranty and limitation of liability provided above cannot be given local legal eect according to their terms, reviewing courts
shall apply local law that most closely approximates an absolute waiver of all civil liability in connection with the Program, unless a warranty or
assumption of liability accompanies a copy of the Program in return for a fee.
117D-Link DIR-882 User Manual
Appendix F - Warranty
Warranty
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this Limited Warranty:
• Only to the person or entity that originally purchased the product from D-Link or its authorized reseller or distributor, and
• Only for products purchased and delivered within the fty states of the United States, the District of Columbia, U.S. Possessions
or Protectorates, U.S. Military Installations, or addresses with an APO or FPO.
Limited Warranty:
D-Link warrants that the hardware portion of the D-Link product described below (“Hardware”) will be free from material defects in workmanship
and materials under normal use from the date of original retail purchase of the product, for the period set forth below (“Warranty Period”), except
as otherwise stated herein.
• Hardware (excluding power supplies and fans): One (1) year
• Power supplies and fans: One (1) year
• Spare parts and spare kits: Ninety (90) days
The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at
D-Link’s option, to repair or replace the defective Hardware during the Warranty Period at no charge to the original owner or to refund the actual
purchase price paid. Any repair or replacement will be rendered by D-Link at an Authorized D-Link Service Oce. The replacement hardware
need not be new or have an identical make, model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any
reconditioned product that D-Link reasonably determines is substantially equivalent (or superior) in all material respects to the defective Hardware.
Repaired or replacement hardware will be warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer,
and is subject to the same limitations and exclusions. If a material defect is incapable of correction, or if D-Link determines that it is not practical
to repair or replace the defective Hardware, the actual price paid by the original purchaser for the defective Hardware will be refunded by D-Link
upon return to D-Link of the defective Hardware. All Hardware or part thereof that is replaced by D-Link, or for which the purchase price is refunded,
shall become the property of D-Link upon replacement or refund.
118D-Link DIR-882 User Manual
Appendix F - Warranty
Limited Software Warranty:
D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional specications
for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety (90)
days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be
free of physical defects. The customer’s sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will
be, at D-Link’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional
specications for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise
agreed by D-Link in writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the
license granted by D-Link for the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject
to the same limitations and exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it
is not practical to replace the non-conforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by
D-Link; provided that the non-conforming Software (and all copies thereof) is rst returned to D-Link. The license granted respecting any Software
for which a refund is given automatically terminates.
Non-Applicability of Warranty:
The Limited Warranty provided hereunder for Hardware and Software portions of D-Link’s products will not be applied to and does not cover any
refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which D-Link, the sellers, or
the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold “As-Is” without any
warranty whatsoever including, without limitation, the Limited Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim (USA):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software
nonconformance in sucient detail to allow D-Link to conrm the same, along with proof of purchase of the product (such as a
copy of the dated purchase invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at https://support.dlink.com, who will attempt to
assist the customer in resolving any suspected defects with the product. If the product is considered defective, the customer must
obtain a Return Material Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number
at https://rma.dlink.com/.
119D-Link DIR-882 User Manual
Appendix F - Warranty
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package
to ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package.
Please refer to shipping and packaging instructions located online at http://rma.dlink.com/.
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD
will either be rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped
to D-Link Systems, Inc., 17595 Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that
are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common
carrier selected by D-Link. Return shipping charges shall be prepaid by D-Link if you use an address in the United States, otherwise
we will ship the product to you freight collect. Expedited shipping is available upon request and provided shipping charges are
prepaid by the customer. D-Link may reject or return any product that is not packaged and shipped in strict compliance with the
foregoing requirements, or for which an RMA number is not visible from the outside of the package. The product owner agrees to
pay D-Link’s reasonable handling and return shipping charges for any product that is not packaged and shipped in accordance
with the foregoing requirements, or that is determined by D-Link not to be defective or non-conforming.
Submitting A Claim (Canada):
The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has expired and
the product is within warranty, the customer shall submit a claim to D-Link as outlined below:
• Customers need to provide their receipt (proof of purchase) even if the product is registered. Without a receipt, no warranty service will
be done. The registration is not considered a proof of purchase.
• The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance
in sucient detail to allow D-Link to conrm the same, along with proof of purchase of the product (such as a copy of the dated purchase
invoice for the product) if the product is not registered.
• The customer must obtain a Case ID Number from D-Link Technical Support at 1-800-361-5265, who will attempt to assist the customer
in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material
Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.ca/.
• After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to
ensure that it will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Do not
include any manuals or accessories in the shipping package. D-Link will only replace the defective portion of the product and will not ship
back any accessories.
120D-Link DIR-882 User Manual
Appendix F - Warranty
• The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will
be rejected by D-Link. Products shall be fully insured by the customer and shipped to D-Link Networks, Inc., 2525 Meadowvale Boulevard
Mississauga, Ontario, L5N 5S2 Canada. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired
or replaced packages will be shipped to the customer via Purolator Canada or any common carrier selected by D-Link. Return shipping
charges shall be prepaid by D-Link if you use an address in Canada, otherwise we will ship the product to you freight collect. Expedited
shipping is available upon request and provided shipping charges are prepaid by the customer. D-Link may reject or return any product
that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA number is not visible from
the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any product
that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or
non-conforming.
• RMA phone number: 1-800-361-5265 Hours of Operation: Monday-Friday, 9:00AM – 9:00PM EST
What Is Not Covered:
The Limited Warranty provided herein by D-Link does not cover:
Products that, in D-Link’s judgment, have been subjected to abuse, accident, alteration, modication, tampering, negligence, misuse, faulty installation,
lack of reasonable care, repair or service in any way that is not contemplated in the documentation for the product, or if the model or serial number
has been altered, tampered with, defaced or removed; Initial installation, installation and removal of the product for repair, and shipping costs;
Operational adjustments covered in the operating manual for the product, and normal maintenance; Damage that occurs in shipment, due to act
of God, failures due to power surge, and cosmetic damage; Any hardware, software, rmware or other products or services provided by anyone
other than D-Link; and Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers,
or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Oce. Improper or incorrectly performed maintenance or repair voids this Limited Warranty.
Disclaimer of Other Warranties:
EXCEPT FOR THE LIMITED WARRANTY SPECIFIED HEREIN, THE PRODUCT IS PROVIDED “AS-IS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER
INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY
SHALL BE LIMITED TO THE DURATION OF THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. EXCEPT AS EXPRESSLY COVERED UNDER THE
LIMITED WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND PERFORMANCE OF THE PRODUCT IS WITH THE
PURCHASER OF THE PRODUCT.
121D-Link DIR-882 User Manual
Appendix F - Warranty
Limitation of Liability:
TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE, STRICT LIABILITY OR OTHER LEGAL
OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF ANY CHARACTER, WHETHER DIRECT, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK
STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT
IS CONNECTED WITH, LOSS OF INFORMATION OR DATA CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK
FOR WARRANTY SERVICE) RESULTING FROM THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF
THIS LIMITED WARRANTY, EVEN IF D-LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF
THE FOREGOING LIMITED WARRANTY IS REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NONCONFORMING PRODUCT. THE MAXIMUM
LIABILITY OF D-LINK UNDER THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING
EXPRESS WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Governing Law:
This Limited Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This
Limited Warranty provides specic legal rights and you may also have other rights which vary from state to state.
Trademarks:
D-Link is a registered trademark of D-Link Corporation/D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their
respective owners.
Copyright Statement:
No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated by the
United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice.
Copyright ©2017 by D-Link Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
122D-Link DIR-882 User Manual
Appendix F - Warranty
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by
one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
Operations in the 5.15-5.25GHz / 5.470 ~ 5.725GHz band are restricted to indoor usage only.
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body. To maintain compliance with FCC RF exposure compliance requirements,
please avoid direct contact to the transmitting antenna during transmitting.
If this device is going to be operated in 5.15 ~ 5.25GHz frequency range, then it is restricted in indoor environment only. This transmitter must not
be co-located or operating in conjunction with any other antenna or transmitter.
The availability of some specic channels and/or operational frequency bands are country dependent and are rmware programmed at the factory
to match the intended destination. The rmware setting is not accessible by the end user.
123D-Link DIR-882 User Manual
Appendix F - Warranty
ICC Notice:
Operation is subject to the following two conditions:
1) This device may not cause interference and
2) This device must accept any interference, including interference that may cause undesired operation of the device.
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating
instructions for satisfying RF exposure compliance. This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
(i) The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to
co-channel mobile satellite systems;
(ii) The maximum antenna gain (2dBi) permitted (for devices in the band 5725-5825 MHz) to comply with the e.i.r.p. limits specied
for point-to-point and non point-to-point operation as appropriate, as stated in section A9.2(3).
In addition, users should also be cautioned to take note that high-power radars are allocated as primary users (meaning they have priority) of the
bands 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.
Règlement d’Industry Canada
Les conditions de fonctionnement sont sujettes à deux conditions:
(1) Ce périphérique ne doit pas causer d’interférence et.
(2) Ce périphérique doit accepter toute interférence, y compris les interférences pouvant perturber le bon fonctionnement de
ce périphérique.
124D-Link DIR-882 User Manual
Appendix G - Registration
Version 1.00 (US)
July 7, 2017
Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.
Registration