Dell Wyse FGYD2 User Manual

Dell Wyse 3040 Thin Client

User Guide

Regulatory Model: N10D

Regulatory Type: N10D001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Dell Wyse external references............................................................................................................................................. 5

2 Wyse 3040 thin client hardware installation....................................................................................6

3 Wyse 3040 thin client on ThinOS................................................................................................... 7

Logging on to the Wyse 3040 thin client running Wyse ThinOS......................................................................... 7

Configuring the dual head display settings in Dell Wyse ThinOS.....................................................................................7

Configuring the network settings on Dell Wyse ThinOS.................................................................................................. 9

Configuring the General settings...................................................................................................................................9

Configuring the DHCP options settings.......................................................................................................................11

Configuring the ENET settings......................................................................................................................................11

Configuring the WLAN settings....................................................................................................................................12

Configuring the broker setup on Dell Wyse ThinOS....................................................................................................... 23

Configuring the WDA settings on Dell Wyse ThinOS..................................................................................................... 25

4 Wyse 3040 thin client on ThinLinux.............................................................................................. 28

Accessing thin client BIOS settings on Wyse ThinLinux.................................................................................................28

Logging on to the Wyse 3040 thin client running ThinLinux......................................................................................... 28

Configuring display on Dell Wyse ThinLinux.....................................................................................................................29

Configuring the network settings on Dell WyseThinLinux............................................................................................. 29

Configuring the wi-fi settings...................................................................................................................................... 30

Configuring wired network connection settings........................................................................................................32

Configuring the network proxy settings..................................................................................................................... 34

Power state...........................................................................................................................................................................41

Configuring connections locally on Dell Wyse ThinLinux.................................................................................................41

Configuring and managing Citrix connections............................................................................................................ 41

Configuring and managing VMware connections......................................................................................................42

Configuring WDA settings on Dell Wyse ThinLinux........................................................................................................ 45

5 Major components of your system............................................................................................... 47

Contents 3

6 System specifications.................................................................................................................48

7 Thermal management on Wyse 3040 thin client ............................................................................50

System Configuration screen options...............................................................................................................................53

Security screen options...................................................................................................................................................... 53

Secure Boot screen options...............................................................................................................................................54

Performance screen options..............................................................................................................................................55

Power Management screen options.................................................................................................................................55

POST Behavior screen options..........................................................................................................................................56

Virtualization support screen options............................................................................................................................... 56

Maintenance screen options..............................................................................................................................................56

System Log screen options................................................................................................................................................56

Updating the BIOS ............................................................................................................................................................. 57

Dell Wyse 3040 thin client is a low-cost entry level thin client platform. These thin clients have a x86 processor, which allows you to run

Wyse ThinOS, PCoIP enabled Wyse ThinOS, and Wyse ThinLinux. The platform is used as a thin client by connecting to any monitor and

allows you to use a remote access client for VDI or cloud-based computing.

About this guide

This guide is intended for Wyse 3040 thin clients which run Wyse ThinOS, PCoIP enabled Wyse ThinOS, and Wyse ThinLinux. It provides

hardware specifications and OS-specific configurations to help you work with Wyse 3040 thin clients.

Dell Wyse external references

For more information on the hardware installation, see

6 Wyse 3040 thin client hardware installation

This section provides the instructions on how to easily configure and efficiently manage Wyse 3040 thin client that runs on ThinOS.

ThinOS users. This option is the default out-of-the-box experience and is recommended for terminal server environments with

published applications and for backward compatibility with ThinOS 6.x versions.

to select. This option is recommended for VDI and any full-screen only connections.

In any desktop case, you can select the desktop option you want (Classic Desktop or Zero Desktop) and create the connections you need

using the Visual Experience tab on the Remote Connections dialog box.

To open the Remote Connections dialog box, perform one of the following tasks:

NOTE: User Name is the user who is logged-on and is located at the lower-left pane of the taskbar

2. Click the Dual Head tab, and use the following guidelines:

Wyse 3040 thin client on ThinOS 7

This feature is applicable for supported dual-monitor-capable thin clients only.

a) Dual Head—Select Mirror Mode to have the two monitors work in a matching state, or Span Mode to have the two monitors

work individually.

b) Main Screen—Select which of the two monitors you want to be the main screen (Screen1 or Screen2). The other screen is

extended from the main screen.

c) Layout—Select how you want the two monitors to be oriented to each other.

Horizontal — where you move between the monitors from the left and right of the screens.

Vertical— where you move between the monitors from the top and bottom of the screens.

will be disabled once you click Save+Exit. You can enable it again by setting rgamma={1-100} ggamma={1-100} bgamma={1-100}

in the Resolution INI parameter. For more information, see Dell Wyse ThinOS INI Guide.

For Swap dual screens, when you set Main Screen to Screen2, an additional check box is displayed at the bottom of the tab that

allows you to swap dual screens. If you clear the check box, the Screen1 is usually the left one or the top one in dual display. When

you set Main Screen to Screen2, the main screen is changed to the right screen or bottom screen. If you select the Swap dual

screens check box, you are able to set Main Screen to Screen2, but still have it at the left side or the top side, which is considered

more user friendly.

Configuring the network settings on Dell Wyse

NOTE: The maximum characters allowed in the Printer Identification field is 31. If your printer driver string is

more than 31 characters (including space), you can create a txt file (printer.txt) and upload to your file server.

Edit the txt file and type the content, such as "HP Color" = "HP Color LaserJet CM1312 MFP PCL6

Class Driver". Add the command line printermap=printer.txt to your wnos.ini file. Now, you can type “HP

Color” in the Printer Identification field instead of the full driver string.

d) Printer Class— This is optional. Select the printer class from the list PCL5, PS, or TXT or PCL4.

e) Enable the printer device — Select this option to enable the directly-connected printer. It enables the device to display on the

remote host.

To configure the LPDs settings:

1. From the desktop menu, click System Setup, and then click Printer.

The Printer Setup dialog box is displayed.

NOTE: Be sure to check with your vendor that the printer can accept Line Printer Request print requests.

a) Select LPD —Select the port you want from the list.

b) Printer Name —(Required) Enter name you want displayed in your list of printers.

c) Printer Identification—Enter the type or model of the printer in the exact text of the Windows printer driver name—including

capitalizations and spaces.

incoming print jobs properly. For example, auto can be used for HP LaserJet 4200n PCL6 as per documentation found on the HP

Web site.

NOTE: If the printer is attached to another thin client on your network, the LPD Queue Name must match the

content of the Printer Name box on the thin client with the printer attached.

g) Enable the printer device—Must be selected to enable the printer. It enables the device so it displays on the remote host.

3. Click OK to save the settings.

NOTE: When the LPD printer is mapped to one session and you cannot access the LPD service host, then the TCP

connection tries to connect to the LPD service host. The timeout period is 60 seconds. During this timeout period, if

you try to close the session, the session waits until the LPD printer connection is established. The initialization

a) Select SMB—Select the SMB you want from the list.

c) Printer Identification—Enter the type or model of the printer in the exact text of the Windows printer driver name—including

This name must be either the device driver name for the printer under the Microsoft Windows system, or a key to map to the

device driver. If not specified, the name will be defaulted to the printer-supplied identification for standard direct-connected USB

printers or Generic / Text for non-USB connected printers upon connection to Windows hosts. The driver name mapping takes

place either through a printer-mapping file read by the system as part of the global profile (wnos.ini) or by MetaFrame servers

e) Printer Class —(Optional) Select the printer class from the list.

If the thin client is to be used as an LPD printer server, DHCP must not be used and a static IP address must be assigned to the

thin client.

3. Click OK to save the settings.

f) If you select Other, you must enter the IP address of the broker server in the Broker Server box.

WDM is selected by default. WDA service automatically runs after the client starts up.

Network name Enter the preferred network name.

Wi-Fi security From the drop-down list, select the security type.

6. On the Network page, click the History button to view the previous Wi-Fi connections and details.

To configure the wired connection settings, perform the following steps:

1. Click the Wired tab. The following attributes are displayed if the network cable is connected to your thin client and wired connection is

• IPv4 Address

• IPv6 Address

• Hardware Address

• IPv4 Address

• IPv6 Address

• Hardware Address

a) Click the ON button to enable the 802.1x Security for your network connection.

b) From the Authentication drop-down list, select the type of authentication you want to set for your network connection. The

available options are:

• TLS

• Protected EAP (PEAP)

You must configure TLS and PEAP using the INI parameters only. Options that you configure using the INI parameters are

populated on the UI screen. For more information about the usage of INI parameters, see Dell Wyse ThinLinux INI Reference Guide.

b) MAC Address—Specifies the MAC address of the network connection.

c) Cloned Address—Specifies the IP address that is cloned by the router.

d) Maximum transmission unit (MTU)—Specifies the size (in bytes) of the largest protocol data unit that the protocol layer can

pass onwards.

e) Firewall Zone—Specifies the security level of the connection.

g) Make available to other users— Select this check box if you want to allow other users to configure these settings.

6. Click the IPv4 tab and do the following:

a) Enable the IPv4 button to configure the IPv4 settings.

b) From the Addresses drop-down menu, select the type of IPv4 configuration. The available options are:

DNS Enable the Automatic button, if you want the thin client to

Server Specifies the IP address of the DNS Server.

Routes Enable the Automatic button to turn on the automatic IPv4

Address Specifies the Router IP address.

Netmask Specifies the Netmask. Netmask is used to divide an IP address

Gateway Specifies the IP address of the default Gateway.

a) Enable the IPv6 button to configure the IPv6 settings.

b) From the Addresses drop-down menu, select the type of IPv6 configuration. The available options are:

• Manual

• Link-Local Only

The IPv6 configuration is similar to configuring the IPv4 Settings. For IPv4 configuration, see the IPv4 settings in this section.

8. Click the Reset tab and do the following:

a) Click Reset to reset the settings for your network connection, including passwords. However, the previous network is displayed as

a preferred network.

b) Click Forget to remove all details relating to this network that you do not want to automatically connect to.

9. Click Apply to save your configured settings.

NOTE: Click the Add Profile tab to add a new network profile. On the right pane, you must configure the following

2. Click VPN to add a VPN network connection. You must import a file from the stored location to configure the VPN settings.

NOTE: The settings are same as configuring the IPv4 settings tab described in this section.

4. Click Team to add and configure the team network connection for your thin client.

a) Click the Team tab, and configure the following options:

1. Interface name—Type the name of your network interface.

and select the type of connection you want to create. The available options are Ethernet, Bond, Bridge, Team, and VLAN.

text box or import a configuration file.

b) To configure the General tab, IPv4 Settings tab, and IPv6 Settings tab for team connection, see the configuration details for

among devices.

5. Enable STP — Select this check box to enable the Spanning Tree Protocol (STP) for your connection.

6. Priority — Enter the priority value.

7. Forward delay — Enter the forward delay duration in seconds.

8. Hello time — Enter the hello time duration in seconds.

9. Max age — Enter the value for the maximum age.

b) To configure the General tab, IPv4 Settings tab, and IPv6 Settings tab for Bridge connection, see the configuration details for

6. Flags—Select the Reorder headers, Generic VLAN Registration Protocol (GVRP), Loose binding, and Multiple VLAN

7. Click Save to save your settings.

Configuring peripherals settings on Wyse

On the System Settings page, click the Peripherals icon. The following tabs are displayed on the left pane of the System Settings page.

The Keyboard setting page enables you to set the Keyboard preferences and make the Keyboard layout.

3. Move the slider to the left to decrease the repeat rate of the pointer or move the slider to the right to increase the repeat rate of the

4. In the keyboard layout box, select the layout you want to use and click Add to include the preferred layout in the currently added

layouts list.

5. Select the preferred keyboard layout from the currently added layouts list, and click Set as Default Layout button to set the default

6. Click Save to save your changes.

By default, the Mouse screen is available in both User mode and Admin mode. Any changes made through the Mouse preferences screen

is saved and continued for the built-in thinuser.

mouse pointer.

4. Click Save to save your changes.

By default, the Printers screen is available only in Admin mode. On the Printer setting page, click the printer icon to start the gnome-

control-center printer.

Figure 11. Printer Settings

Figure 12. Add New Printer

1. Click the printer icon.

The gnome-control-center printer dialog box is displayed.

2. Click Add New Printer button to include the new printer in the printers list available on the left pane.

By default, the Sound screen is available in both User mode and Admin mode. Any changes made through Sound screen is saved and

retained for the built-in thinuser.

Figure 13. Sound Settings

a) Move the Output volume slider to adjust the output or speaker volume. Click the Output volume button to enable or disable the

output volume.

b) Select the device for sound output from the listed output devices. The default audio output is the Analog Output.

c) Based on the channels available for the selected output device and profile, you can adjust the Balance and Fade values by moving

Balance and Fade sliders respectively.

d) Select the audio profile from the drop-down list.

e) Click the Test Speakers option. A dialog box is displayed. You can perform the speaker testing by playing sample wave files.

Wyse 3040 thin client running Wyse ThinLinux

On your initial configuration, Dell recommends that you connect by using a wired connection by plugging in the network connected

Ethernet cable to your thin client.

After you turn on your thin client, you are automatically logged in to the thinuser account. By default, the password of the thinuser

account is set to thinuser.

NOTE: In cases where a GDM login is needed (for example, AD/Domain login, the PNAgent login, and so on), the

autologin option can be turned off through the GUI or by using the INI.

Admin mode enables you to perform system administration tasks such as adding or removing connections and setting up specific device

settings. To enter into the Admin mode, click the Switch to Admin button from Setting application screen to admin mode and then enter

the default root password in the Password Needed window. The default root password is admin.

The Citrix Connections page enables you to create and manage the Citrix connections both locally and globally.

Figure 15. Citrix connection settings

To configure the local Citrix settings:

Table 7. Brand / Sub-brand / Model number / Chassis description / Series level / Category type

Audio universal jack 1x Audio universal jack

Table 11. I/O (rear)

USB 2.0 2x USB 2.0 (stacked)

Display Port 2x DP

Physical security (Right side) 1x Kensington Lock Slot

Network 1x UTP, RJ-45

48 System specifications

New Chassis New Dell Wyse ID

Height (Z) mm 27.94

Power input voltage range 3 A, 5 Vdc. Complies with L.P.S.

Power input voltage range 2 A, 12 Vdc. Complies with L.P.S

Table 14. BIOS

Standard BIOS, UEFI as implemented using AMI Dell BIOS Y

Support Wake-On-LAN Y

Table 15. Operating system

OS and system software Launch at RTS

• ThinLinux 1.0.4 (post RTS)

System specifications 49

• Intel Turbo Boost

The Intel Cherry Trail SOC has inbuilt thermal control that prevents overheating of the thin client. When the temperature of the SOC

crosses a preset value (PL1), the CPU speed drops to a lower speed to cool down the SOC and prevent overheating. The PL1 value is set

in the BIOS.

Intel Turbo Boost allows the processor cores to work more than the rated operating frequency. Intel Turbo Boost is activated when the

operating system requires a frequency higher than the rated frequency of the processor. The performance and frequency of Intel Turbo

Boost Technology depends on the following factors:

• Type of workload

• Number of active cores

• Estimated current consumption

by the Intel Turbo Boost that can be enabled or disabled in the BIOS settings. When enabled, the dynamic overclocking occurs in the

operating system. When disabled, the dynamic overclocking does not occur.

The BIOS on Wyse 3040 thin client has PL1 set to 2.2 W and the SOC thermal sensor triggers a CPU throttle when the temperature of

the SOC exceeds 83º C. This indicates that when the GPU/CPU combined workload exceeds 2.2 W or temperature exceeds 83º C, the

SOC starts throttling the CPU speed to 480 Mhz. After throttling if the temperature drops, the CPU goes back to the normal speed of

1.44 GHz.

When the Intel Turbo Boost is enabled, the BIOS could increase the speed of the CPU cores to a higher speed temporarily depending on

the operating system workload. The thermal limits of the SOC are increased. When this happens, the CPU speed drops to 480 Mhz to

protect the SOC from overheating. This throttling happens as soon as the thermal limit is reached.

When the Intel Turbo Boost is not enabled, there is no over clocking of the CPU. When the operating system is under normal workloads,

50 Thermal management on Wyse 3040 thin client

This section describes how to enter the BIOS settings/System Setup and configure the BIOS options of your thin client.

Accessing thin client BIOS settings

This section describes about the Wyse 3040 thin client UEFI BIOS settings. While starting a thin client, a Dell logo is displayed for a short

1. During the start-up, press the F2 key. and the default password is Fireport

2. The BIOS setting is protected by a password. When promoted, enter the password Fireport.

To access the boot menu, during the start-up, press the F12 key. Use the boot selection menu to select or view the boot sequence order

as follows:

• Boot from UEFI: Hard Drive, Partition 2 (for ThinLinux clients), Partition 4 (for ThinOS clients)—Boots from the internal eMMC

• Boot from IP4 Realtek PCIe GBE Family Controller—Boots from the network through PXE.

• Boot from IP6 Realtek PCIe GBE Family Controller—Boots from the network through PXE

• Boot from USB—Boots the USB storage from any of the USB ports. This option is displayed if bootable USB devices are plugged in.

System Setup overview

System Setup allows you to:

• Change the system configuration information after you add, change, or remove any hardware in your thin client.

CAUTION: Unless you are an expert thin client user, do not change the settings for this program. Certain changes can

• Access System Setup by pressing F2 key

• Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option. The boot menu options are:

• UEFI Boot

• UEFI: Hard drive details

• IP4 Realtek PCIe GBE Family Controller

• IP6 Realtek PCIe GBE Family Controller

• Other options

• BIOS Setup

• BIOS Flash Update

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Selects a value in the selected field (if applicable) or follow the link in the field.

Spacebar Expands or collapses a drop-down list, if applicable.

Tab Moves to the next focus area.

Esc Moves to the previous page until you view the main screen. Pressing Esc in the main screen displays a message

General screen options

This section lists the primary hardware features of your computer.

Boot Sequence Boot Sequence Allows you to change the order in which the computer attempts to find an operating

52 BIOS overview

System Configuration screen options

UEFI Network

Integrated NIC Allows you to configure the integrated network controller. The options are:

NOTE: If Strong Password is enabled, Admin and System passwords must contain at least one

54 BIOS overview

Performance screen options

POST Behavior screen options

Fastboot Allows you to speed up the boot process by bypassing some of the compatibility steps. The options are:

Extended BIOS

POST Time

Virtualization support screen options

Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option is not set by default.

BIOS Downgrade This controls flashing of the system firmware to previous revisions.

Data Wipe Select the Wipe on Next Boot check box if you want to erase the data from all internal storage devices on next

56 BIOS overview

Updating the BIOS

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

Follow the instructions on the screen.

NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If you want to update

the BIOS from 1.0 to 7.0, then install version 4.0 first and then install version 7.0.