Dell Latitude 7370 Owner's Manual
Working on your computer
Removing and installing components
Technology and Components
System Setup
Diagnostics
- Enhanced Pre-Boot System Assessment (ePSA) diagnostics
- Device status lights
Technical specifications
Contacting Dell

DELL 13 User Manual

Displayed below is the user manual for 13 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

DELL 13 Manual

Dell Latitude 7370

Owner's Manual

Regulatory Model: P67G

Regulatory Type: P67G001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2016 - 03

Rev. A00

Contents

1 Working on your computer.................................................................................7

Safety instructions................................................................................................................................. 7

Before working inside your computer..................................................................................................8

Turning off your computer................................................................................................................... 8

After working inside your computer.....................................................................................................9

2 Removing and installing components............................................................10

Recommended tools...........................................................................................................................10

Installing the micro Subscriber Identification Module (SIM) card..................................................... 10

Removing the micro Subscriber Identification Module (SIM) card....................................................11

Removing the micro Secure Digital (SD) card.................................................................................... 11

Installing the micro Secure Digital (SD) card...................................................................................... 11

Removing the base cover....................................................................................................................11

Installing the base cover......................................................................................................................12

Removing the battery..........................................................................................................................12

Installing the battery............................................................................................................................13

Removing the coin cell battery...........................................................................................................14

Installing the coin cell battery.............................................................................................................15

Removing the smart card cage...........................................................................................................15

Installing the smart card cage.............................................................................................................15

Removing the speakers....................................................................................................................... 16

Installing the speakers......................................................................................................................... 16

Removing the WLAN card................................................................................................................... 17

Installing the WLAN card.....................................................................................................................18

Removing the WWAN card................................................................................................................. 19

Installing the WWAN card...................................................................................................................20

Removing the Solid State Drive (SSD)................................................................................................ 20

Installing the Solid State Drive(SSD)....................................................................................................21

Removing the display assembly..........................................................................................................22

Installing the display assembly........................................................................................................... 24

Removing the system board...............................................................................................................24

Installing the system board.................................................................................................................26

Removing the keyboard .....................................................................................................................26

Installing the keyboard........................................................................................................................28

Removing the palmrest ......................................................................................................................28

Installing the palmrest.........................................................................................................................29

3 Technology and Components......................................................................... 30

Power adapter.....................................................................................................................................30

Processors...........................................................................................................................................30

Identifying processors in Windows 10............................................................................................... 30

Identifying processors in Windows 8................................................................................................. 30

Verifying the processor usage in Task Manager.................................................................................31

Verifying the processor usage in Resource Monitor..........................................................................31

Chipsets............................................................................................................................................... 32

Downloading the chipset driver......................................................................................................... 32

Identifying the chipset in Device Manager on Windows 10.............................................................. 32

Identifying chipset in Device Manager on Windows 8...................................................................... 33

Graphic options...................................................................................................................................33

Downloading Drivers.......................................................................................................................... 34

Identifying the display adapter........................................................................................................... 34

Changing the screen resolution.........................................................................................................34

Rotating the display.............................................................................................................................35

Display options....................................................................................................................................35

Adjusting brightness in Windows 10...................................................................................................35

Adjusting brightness in Windows 8.................................................................................................... 35

Cleaning the display............................................................................................................................35

Using touch screen in Windows 10....................................................................................................36

Using touch screen in Windows 8......................................................................................................36

Connecting to external display devices............................................................................................. 36

Realtek ALC3266–CG Waves MaxxAudio Pro controller.................................................................. 37

Downloading the audio driver...................................................................................................... 37

Identifying the audio controller in Windows 10...........................................................................37

Identifying the audio controller in Windows 8.............................................................................37

Changing the audio settings.........................................................................................................38

WLAN cards......................................................................................................................................... 38

Secure Boot screen options......................................................................................................... 38

Hard drive options...............................................................................................................................39

Identifying the hard drive in Windows 10.....................................................................................39

Identifying the hard drive in Windows 8.......................................................................................39

Entering BIOS setup...................................................................................................................... 39

Camera features..................................................................................................................................39

Identifying the camera in Device Manager on Windows 10....................................................... 40

Identifying the camera in Device Manager on Windows 8......................................................... 40

Starting the camera.......................................................................................................................40

Starting the Camera App.............................................................................................................. 40

Memory features................................................................................................................................. 41

Verifying system memory in Windows 10....................................................................................42

Verifying system memory in Windows 8......................................................................................42

Verifying system memory in setup............................................................................................... 42

Testing memory using ePSA.........................................................................................................42

Intel chipset drivers.............................................................................................................................42

Intel HD Graphics drivers....................................................................................................................43

Realtek HD audio drivers.................................................................................................................... 43

4 System Setup.......................................................................................................44

Boot Sequence....................................................................................................................................44

Navigation keys................................................................................................................................... 44

System setup options..........................................................................................................................45

General screen options.......................................................................................................................45

System Configuration screen options................................................................................................46

Video screen options..........................................................................................................................48

Security screen options...................................................................................................................... 48

Secure Boot screen options............................................................................................................... 50

Intel Software Guard Extensions screen options............................................................................... 51

Performance screen options...............................................................................................................51

Power Management screen options.................................................................................................. 52

POST Behavior screen options...........................................................................................................53

Virtualization support screen options................................................................................................ 54

Wireless screen options...................................................................................................................... 55

Maintenance screen options.............................................................................................................. 55

System Log screen options................................................................................................................ 56

Updating the BIOS ..............................................................................................................................56

System and setup password............................................................................................................... 57

Assigning a system password and setup password......................................................................57

Deleting or changing an existing system and/or setup password.............................................. 58

5 Diagnostics.......................................................................................................... 59

Enhanced Pre-Boot System Assessment (ePSA) diagnostics............................................................59

Device status lights............................................................................................................................. 60

6 Technical specifications....................................................................................61

System specifications.......................................................................................................................... 61

Processor specifications..................................................................................................................... 61

Memory specifications........................................................................................................................ 61

Audio specifications............................................................................................................................62

Video specifications............................................................................................................................ 62

Camera specifications.........................................................................................................................62

Communication specifications...........................................................................................................62

Port and connector specifications..................................................................................................... 63

Display specifications..........................................................................................................................63

Keyboard specifications......................................................................................................................64

Touchpad specifications.....................................................................................................................64

Battery specifications..........................................................................................................................64

AC Adapter specifications...................................................................................................................65

Physical specifications........................................................................................................................ 66

Environmental specifications............................................................................................................. 66

7 Contacting Dell................................................................................................... 67

Working on your computer

Safety instructions

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

Before working inside your computer

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that you follow the Safety instructions.

2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

3. Turn off your computer, see Turning off your computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all the network cables from the computer.

5. Disconnect your computer and all attached devices from the electrical outlets.

6. Press and hold the power button while the computer is unplugged to ground the system board.

7. Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

Turning off your computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Turning off your computer:

• In Windows 10 (using a touch enabled device or mouse):

1. Click or tap .

2. Click or tap and then click or touch Shut down.

• In Windows 8 (using a touch enabled device):

1. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.

2. Tap and then tap Shut down

• In Windows 8 (using a mouse):

1. Point to upper-right corner of the screen and click Settings.

2. Click and then click Shut down.

• In Windows 7:

1. Click Start.

2. Click Shut Down.

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After working inside your computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Replace the base cover.

5. Connect your computer and all attached devices to their electrical outlets.

6. Turn on your computer.

Removing and installing components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended tools

The procedures in this document require the following tools:

• Small flat blade screwdriver

• Phillips screwdriver

• Small plastic scribe

Installing the micro Subscriber Identification Module

(SIM) card

1. Follow the procedure in Before working inside your computer.

2. Insert a paperclip or a SIM card removal tool into the pinhole to remove the SIM card tray [1].

3. Place the micro SIM card on the SIM card tray [2].

4. Push the SIM card tray into the slot until it clicks into place.

Removing the micro Subscriber Identification Module

(SIM) card

CAUTION: Removing the micro SIM card when the computer is on may cause data loss or damage

the card. Ensure that your computer is turned off or the network connections are disabled.

1. Insert a paperclip or a SIM card removal tool into the pinhole on the SIM card tray.

2. Remove the micro SIM card from the SIM card tray.

3. Push the SIM card tray into the slot until it clicks into place.

Removing the micro Secure Digital (SD) card

1. Follow the procedure in Before working inside your computer.

2. Press in the micro SD card to release it from the computer. Slide the micro SD card out of the

computer.

Installing the micro Secure Digital (SD) card

1. Push in the micro SD card into its slot until it clicks into place.

2. Follow the procedure in After working inside your computer.

Removing the base cover

1. Follow the procedure in Before working inside your computer.

2. To remove the base cover:

a. Loosen the captive screws that secure the base cover to the computer [1].

b. Lift the base cover from the edge and remove it from the computer [2].

Installing the base cover

1. Align the tabs on the base cover with the slots on the computer.

2. Tighten the screws to secure the base cover to the computer.

3. Press the edges of the cover until it clicks into place.

4. Follow the procedure in After working inside your computer.

Removing the battery

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover.

3. Disconnect the battery cable from the connector on the system board [1].

4. To remove the battery:

a. Remove the screws that secure the battery to the computer [1].

b. Lift the battery away from the computer [2].

Installing the battery

1. Align the tabs on the battery with the slots on the palmrest.

2. Tighten the screws to secure the battery to the computer.

NOTE: The number of screws vary depending on the type of battery.

3. Connect the battery cable to the connector on the system board.

4. Install the base cover.

5. Follow the procedure in After working inside your computer.

Removing the coin cell battery

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

3. Disconnect the battery cable from the connector on the system board [1].

4. To remove the coin cell battery:

a. Disconnect the coin cell battery cable from the connector on the system board [1].

b. Lift the coin cell battery to release it from the adhesive and remove it from the system board [2].

Installing the coin cell battery

1. Place the coin cell battery into the slot on the system board.

2. Connect the coin cell battery cable to the connector on the system board.

3. Connect the battery cable to the connector on the system board.

4. Install the:

a. base cover

5. Follow the procedure in After working inside your computer.

Removing the smart card cage

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

b. battery

3. To remove the smart card cage:

a. Disconnect the smart card FFC cable [1,2].

b. Remove the screws that secure the smart card cage to the system board [3].

c. Lift the smart card cage from the system board [4].

Installing the smart card cage

1. Place the smart card cage on the system board.

2. Tighten the screw to secure the smart card cage to the computer.

3. Connect the smart card FFC cable to the system board.

4. Install the:

a. battery

b. base cover

5. Follow the procedure in After working inside your computer.

Removing the speakers

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

b. battery

3. To remove the speakers:

a. Disconnect the speaker cable [1].

b. Unroute the speaker cable [2].

c. Remove the speakers from the computer [3].

NOTE: Use a plastic scribe to detach the speakers from the adhesive pads.

Installing the speakers

1. Place the speakers to align with the alignment lines on the computer.

2. Route the speaker cable through the retention clips on the dock frame.

3. Connect the speaker cable to its connector on the system board.

4. Install the:

a. battery

b. base cover

5. Follow the procedure in After working inside your computer.

Removing the WLAN card

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

3. Disconnect the battery cable from the connector on the system board [1].

4. To remove the WLAN card:

a. Remove the screw that secures the metal bracket to the WLAN card [1].

b. Remove the metal bracket [2].

c. Disconnect the WLAN cables from the connectors on the WLAN card [3].

d. Remove the WLAN card from the computer [4].

Installing the WLAN card

1. Insert the WLAN card into the slot on the computer.

2. Route the WLAN cables through the routing channel.

3. Connect the WLAN cables to the connectors on the WLAN Card.

4. Place the metal bracket and tighten the screw to secure it to the computer.

5. Connect the battery cable to the connector on the system board.

6. Install the:

a. base cover

7. Follow the procedure in After working inside your system.

Removing the WWAN card

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

3. Disconnect the battery cable from the connector on the system board [1].

4. To remove the WWAN card:

a. Peel the aluminum foil until the folding line.

b. Remove the screw that secures the metal bracket to the WWAN card [1].

c. Remove the metal bracket [2].

d. Disconnect the WWAN cables from the connectors on the WWAN card [3].

e. Remove the WWAN card from the computer [4].

Installing the WWAN card

1. Peel the aluminum foil until the folding line.

2. Insert the WWAN card into the slot on the computer.

3. Route the WWAN cables through the routing channel.

4. Connect the WWAN cables to the connectors on the WWAN Card.

5. Place the metal bracket and tighten the screw to secure it to the computer.

6. Stick the aluminum foil on the bracket and WWAN card.

7. Connect the battery cable to the connector on the system board.

8. Install the:

a. base cover

9. Follow the procedure in After working inside your system.

Removing the Solid State Drive (SSD)

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

3. Disconnect the battery cable from the connector on the system board [1].

4. To remove the SSD:

a. Peel the aluminum foil until the folding line.

b. Remove the screw that secures the SSD to the computer [1].

c. Remove the SSD bracket [2].

d. Remove the copper thermal plate.

e. Remove the SSD from the computer [3].

Installing the Solid State Drive(SSD)

1. Insert the SSD into the connector on the computer.

2. Install the thermal plate.

3. Install the metal bracket.

4. Tighten the screw to secure the SSD to the computer.

5. Stick the aluminum foil on the thermal plate.

6. Connect the battery cable to the connector on the system board.

7. Install the:

a. base cover

8. Follow the procedure in After working inside your computer.

Removing the display assembly

1. Follow the procedure in Before working inside your computer.

2. Remove the base cover

3. Disconnect the battery cable from the connector on the system board [1].

4. Remove the:

a. WLAN card

b. WWAN card

5. To remove the cables:

a. Disconnect the camera and tune cable [1, 2].

b. Peel the aluminum foil until the folding line.

c. Remove the screws that secure the metal plate and lift it away from the computer [3, 4].

d. Peel the adhesive to access the display cable and disconnect it from the connector [5].

e. Disconnect the touch-panel cable from the computer [6].

6. Lift to separate the palmrest assembly from the display assembly.

7. To remove the display assembly:

a. Remove the screws that secure the display assembly to the computer [1].

b. Slide the display assembly to release it from the computer [2].

Installing the display assembly

1. Connect the display cable to the connector and fix the adhesive tape.

2. Stick the aluminum foil on the thermal plate and display cable.

3. Connect the camera, touch-panel, and tune cable.

4. Align the display assembly with the screw holders on the computer.

5. Tighten the screws to secure the display assembly.

6. Install the:

a. WWAN card

b. WLAN card

7. Connect the battery cable to the connector on the system board.

8. Install the base cover.

9. Follow the procedure in After working inside your system.

Removing the system board

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

b. battery

c. SSD

d. WLAN card

e. WWAN card

f. coin cell

g. display

3. Disconnect the following cables from the system board:

a. speaker cable

b. touch pad cable

c. smart card cable

d. LED cable

e. array mic cable

f. finger print cable

g. WWAN AUX antenna cable

h. NFC cable

4. To remove the system board:

a. Remove the screws that secure the system board to the computer [1].

b. Remove the screws that secure the metal tab and remove it from the computer [2, 3].

5. Lift the system board from the computer.

Installing the system board

1. Align the system board with the screw holders on the computer.

2. Tighten the screws to secure the system board to the computer.

3. Tighten the screws to secure the metal tab over the USB type C port.

4. Connect the following cables to the connectors on the system board:

a. speaker cable

b. smart card cable

c. LED cable

d. array mic cable

e. touch pad cable

f. finger print cable

g. WWAN AUX antenna cable

h. NFC cable

5. Install the:

a. display

b. coin cell

c. WWAN card

d. WLAN card

e. SSD

f. battery

g. base cover

6. Follow the procedure in After working inside your computer.

Removing the keyboard

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

b. battery

c. SSD

d. WLAN card

e. WWAN card

f. coin-cell

g. display

h. system board

3. To remove the keyboard:

a. Disconnect the keyboard cables from the connectors on the system board [1, 2].

b. Remove the screws that secure the keyboard to the computer [3].

c. Lift the metal tab away from the computer [4].

4. To remove the keyboard:

a. Remove the screws that secure the keyboard to the computer [1].

b. Lift the keyboard from the computer [2].

Installing the keyboard

1. Align the keyboard with the screw holders on the computer.

2. Tighten the screws to secure the keyboard to the computer.

3. Tighten the screw that secures the metal tab on the system board.

4. Connect the keyboard cables to the connectors on the system board.

5. Install the:

a. system board

b. display

c. SSD

d. WWAN

e. WLAN

f. coin cell

g. battery

h. base cover

6. Follow the procedure in After working inside your system.

Removing the palmrest

1. Follow the procedure in Before working inside your computer.

2. Remove the:

a. base cover

b. battery

c. SSD

d. WWAN card

e. WLAN card

f. coin-cell

g. smart-card cage

h. speakers

i. display assembly

j. system board

k. keyboard

3. Remove the palmrest assembly away from the computer.

Installing the palmrest

1. Place the palmrest on the computer.

2. Install the:

a. keyboard

b. system board

c. display assembly

d. speakers

e. smart-card cage

f. coin cell

g. WLAN card

h. WWAN card

i. SSD

j. battery

k. base cover

3. Follow the procedure in After working inside your system.

Technology and Components

Power adapter

This laptop is offered with the 45 W power adapter. This adapter uses a USB C connector.

WARNING: When you disconnect the power adapter cable from the laptop, grasp the connector,

not the cable itself, and then pull firmly but gently to avoid damaging the cable.

WARNING: The power adapter works with electrical outlets worldwide. However, power

connectors and power strips vary among countries. Using an incompatible cable or improperly

connecting the cable to the power strip or electrical outlet may cause fire or equipment damage.

Processors

This laptop is shipped with the following processors:

• Intel Core M3-6Y30

• Intel Core M5-6Y57

• Intel Core M7-6Y75

NOTE: The clock speed and performance varies depending on the workload and other variables.

Identifying processors in Windows 10

1. Tap Search the Web and Windows.

2. Type Device Manager.

3. Tap Processor.

The basic information of the processor is displayed.

Identifying processors in Windows 8

1. Tap Search the Web and Windows.

2. Type Device Manager.

3. Tap Processor.

The basic information of the processor is displayed.

Verifying the processor usage in Task Manager

1. Press and hold the taskbar.

2. Select Start Task Manager.

The Windows Task Manager window is displayed.

3. Click the Performance tab in the Windows Task Manager window.

The processor performance details are displayed.

Verifying the processor usage in Resource Monitor

1. Press and hold the taskbar.

2. Select Start Task Manager.

The Windows Task Manager window is displayed.

3. Click the Performance tab in the Windows Task Manager window.

The processor performance details are displayed.

4. Click Open Resource Monitor.

Chipsets

All laptop communicate with the CPU through the chipset. This laptop is shipped with the Intel 100 Series

chipset.

Downloading the chipset driver

1. Turn on the laptop.

2. Go to www.dell.com/support.

3. Click Product Support, enter the Service Tag of your laptop, and then click Submit.

NOTE: If you do not have the Service Tag, use the autodetect feature or manually browse for

your laptop model.

4. Click Drivers and Downloads.

5. Select the operating system installed on your laptop.

6. Scroll down the page, expand Chipset, and select your chipset driver.

7. Click Download File to download the latest version of the chipset driver for your laptop.

8. After the download is complete, navigate to the folder where you saved the driver file.

9. Double-click the chipset driver file icon and follow the instructions on the screen.

Identifying the chipset in Device Manager on Windows 10

1. Click All Settings on the Windows 10 Charms Bar.

2. From the Control Panel, select Device Manager.

3. Expand System Devices and search for the chipset.

Identifying chipset in Device Manager on Windows 8

1. Click Settings on the Windows 8.1 Charms Bar.

2. From the Control Panel, select Device Manager.

3. Expand System Devices and search for the chipset.

Graphic options

This laptop is shipped with the Intel HD Graphics 515 graphics chipset.

Downloading Drivers

1. Turn on the laptop.

2. Go to www.dell.com/support.

3. Click Product Support, enter the Service Tag of your laptop, and then clickSubmit.

NOTE: If you do not have the Service Tag, use the auto detect feature or manually browse for

your laptop model.

4. Click Drivers and Downloads.

5. Select the operating system installed on your laptop.

6. Scroll down the page and select the graphic driver to install.

7. Click Download File to download the graphic driver for your laptop.

8. After the download is complete, navigate to the folder where you saved the graphic driver file.

9. Double-click the graphic driver file icon and follow the instructions on the screen.

Identifying the display adapter

1. Start the Search Charm and select Settings.

2. Type Device Manager in the search box and tap Device Manager from the left pane.

3. Expand Display adapters.

The display adapters are displayed.

Changing the screen resolution

1. Press and hold the desktop screen and select Display Settings.

2. Tap or click Advanced display settings.

3. Select the required resolution from the drop-down list and tap Apply.

Rotating the display

1. Press and hold on the desktop screen.

A sub menu is displayed.

2. Select Graphic Options → Rotation and choose on of the following:

• Rotate to Normal

• Rotate to 90 Degrees

• Rotate to 180 Degrees

• Rotate to 270 Degrees

NOTE: The Display can also be rotated using the following key combinations:

• Ctrl + Alt + Up arrow key (Rotate to normal)

• Right arrow key (Rotate 90 degrees)

• Down arrow key (Rotate 180 degrees)

• Left arrow key (Rotate 270 degrees)

Display options

This laptop has 11.57– inch FHD with 1920 x 1080 resolution (maximum) and QHD with 3200 x 1800

resolution (maximum).

Adjusting brightness in Windows 10

To enable or disable automatic screen brightness adjustment:

1. Swipe-in from the right edge of the display to access the Action Center.

2. Tap or click All Settings → System → Display.

3. Use the Adjust my screen brightness automatically slider to enable or disable automatic-brightness

adjustment.

NOTE: You can also use the Brightness level slider to adjust the brightness manually.

Adjusting brightness in Windows 8

To enable or disable automatic screen brightness adjustment:

1. Swipe-in from the right edge of the display to access the Charms menu.

2. Tap or click Settings → Change PC Settings → PC and devices→ Power and sleep.

3. Use the Adjust my screen brightness automatically slider to enable or disable automatic-brightness

adjustment.

Cleaning the display

1. Check for any smudges or areas that has to be cleaned.

2. Use a microfiber cloth to remove any obvious dust and gently brush off any dirt particles.

3. Proper cleaning kits should be used to clean and keep your display in a crisp clear pristine condition.

NOTE: Never spray any cleaning solutions directly on the screen; spray it to the cleaning cloth.

4. Gently wipe the screen in a circular motion. Do not press hard on the cloth.

NOTE: Do not press hard or touch the screen with your fingers or you may leave oily prints and

smears.

NOTE: Do not leave any liquid on the screen.

5. Remove all excess moisture as it may damage your screen.

6. Let the display dry thoroughly before you turn it on.

7. For stains that are hard to remove, repeat this procedure till the display is clean.

Using touch screen in Windows 10

Follow these steps to enable or disable the touch screen:

1. Go to the Charms Bar and tap All Settings .

2. Tap Control Panel.

3. Tap Pen and Input Devices in the Control Panel.

4. Tap the Touch tab.

5. Select Use your finger as an input device to enable the touch screen. Clear the box to disable the

touch screen.

Using touch screen in Windows 8

Follow these steps to enable or disable the touch screen:

1. Go to the Charms Bar and tap Settings .

2. Tap Control Panel.

3. Tap Pen and Input Devices in the Control Panel.

4. Tap the Touch tab.

5. Select Use your finger as an input device to enable the touch screen. Clear the box to disable the

touch screen.

Connecting to external display devices

Follow these steps to connect your laptop to an external display device:

1. Ensure that the projector is turned on and plug the projector cable into a video port on your laptop.

2. Press the Windows logo+P key.

3. Select one of the following modes:

• PC screen only

• Duplicate

• Extend

• Second Screen only

NOTE: For more information, see the document that shipped with your display device.

Realtek ALC3266–CG Waves MaxxAudio Pro controller

This laptop ships with integrated Realtek ALC3266–CG Waves MaxxAudio Pro controller. It is a High

Definition audio codec designed for Windows desktop and laptops.

Downloading the audio driver

1. Turn on the laptop.

2. Go to www.dell.com/support.

3. Click Product Support, enter the Service Tag of your laptop and click Submit.

NOTE: If you do not have the Service Tag, use the autodetect feature or manually browse for

your laptop model.

4. Click Drivers and Downloads.

5. Select the operating system installed on your laptop.

6. Scroll down the page and expand Audio.

7. Select the audio driver.

8. Click Download File to download the latest version of the audio driver for your laptop.

9. After the download is complete, navigate to the folder where you saved the audio driver file.

10. Double-click the audio driver file icon and follow the instructions on the screen.

Identifying the audio controller in Windows 10

1. Start the Search Charm and select All Settings .

2. Type Device Manager in the search box and select Device Manager from the left pane.

3. Expand Sound, video and game controllers.

The audio controller is displayed.

Table 1. Identifying the audio controller in Windows 10

Before installation After installation

Identifying the audio controller in Windows 8

1. Start the Search Charm and select Settings .

2. Type Device Manager in the search box and select Device Manager from the left pane.

3. Expand Sound, video and game controllers.

The audio controller is displayed.

Table 2. Identifying the audio controller in Windows 8

Before installation After installation

Changing the audio settings

1. Start the Search Charm and type Dell Audio in the search box.

2. Start the Dell Audio utility from the left pane.

WLAN cards

This laptop supports the Intel Dual Band Wireless AC 8260 WLAN card.

Secure Boot screen options

Option Description

Secure Boot

Enable

This option enables or disables the Secure Boot feature.

• Disabled

• Enabled

Default setting: Enabled.

Expert Key

Management

Allows you to manipulate the security key databases only if the system is in Custom

Mode. The Enable Custom Mode option is disabled by default. The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx

appear. The options are:

•Save to File—Saves the key to a user-selected file

•Replace from File—Replaces the current key with a key from a user-selected

file

•Append from File—Adds a key to the current database from a user-selected file

•Delete—Deletes the selected key

•Reset All Keys—Resets to default setting

•Delete All Keys—Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will be erased

and the keys will restore to default settings.

Hard drive options

This laptop supports M.2 SATA drive and M.2 NVMe drive.

Identifying the hard drive in Windows 10

1. Tap or click All Settings on the Windows 10 Charms Bar.

2. Tap or click Control Panel, select Device Manager , and expand Disk drives.

The hard drive is listed under Disk drives.

Identifying the hard drive in Windows 8

1. Tap or click Settings on the Windows 8 Charms Bar.

2. Tap or click Control Panel, select Device Manager, and expand Disk drives.

The hard drive is listed under Disk drives.

Entering BIOS setup

1. Turn on or restart your laptop.

2. When the Dell logo appears, perform one of the following actions to enter the BIOS setup program:

• With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot

selection menu, tap F12.

• Without keyboard — When the F12 boot selection menu is displayed, press the Volume Down

button to enter BIOS setup. To enter the Boot selection menu, press the Volume Up button.

Hard drive is listed under the System Information under the General group.

Camera features

This laptop comes with front-facing camera with the image resolution of 1280 x 720 (maximum).

NOTE: The camera is located at the bottom left corner of the LCD.

Identifying the camera in Device Manager on Windows 10

1. In the Search box, type device manager, and tap to start it.

2. Under Device Manager, expand Imaging devices.

Identifying the camera in Device Manager on Windows 8

1. Start the Charms Bar from the desktop interface.

2. Select Control Panel.

3. Select Device Manager and expand Imaging devices.

Starting the camera

To start the camera, open an application that uses the camera. For instance, if you tap the Dell webcam

central software or the Skype software that is shipped with the laptop, the camera turns on. Similarly, if

you are chatting on the internet and the application requests to access the webcam, the webcam turns

on.

Starting the Camera App

1. Tap or click the Windows button and select All apps.

2. Select Camera from the apps list.

3. If the Camera App is not available in the apps list, search for it.

Memory features

In this laptop, the memory (RAM) is a part of the system board. This laptop supports 4–16 GB LPDDR3

memory, up to 1600 MHz.

NOTE: Since memory is part of the system board, it cannot be upgraded as a separate module. If

the technical support determines that the memory is the cause of an issue, replace the system

board.

Verifying system memory in Windows 10

1. Tap the Windows button and select All Settings → System .

2. Under System, tap About.

Verifying system memory in Windows 8

1. From your desktop, start the Charms Bar.

2. Select Control Panel and then select System.

Verifying system memory in setup

1. Turn on or restart your laptop.

2. Perform one of the following actions after the Dell logo is displayed:

• With keyboard — Tap F2 until the Entering BIOS setup message appears. To enter the Boot

selection menu, tap F12.

• Without keyboard — When the F12 boot selection menu is displayed, press the Volume Down

button to enter BIOS setup. To enter the Boot selection menu, press the Volume Up button.

3. On the left pane, select Settings → General → System Information,

The memory information is displayed on the right pane.

Testing memory using ePSA

1. Turn on or restart your laptop.

2. Perform one of the following actions after the Dell logo is displayed:

• With keyboard — Press F2.

• Without keyboard — Press and hold the Volume Up button when the Dell logo is displayed on the

screen. When the F12 boot selection menu is displayed, select Diagnostics from the boot menu,

and press Enter.

The PreBoot System Assessment (PSA) starts on your laptop.

NOTE: If you wait too long and the operating system logo appears, continue to wait until you

see the desktop. Turn off the laptop and try again.

Intel chipset drivers

Verify if the Intel chipset drivers are already installed in the laptop.

Table 3. Intel chipset drivers

Before installation After installation

Intel HD Graphics drivers

Verify if the Intel HD Graphics drivers are already installed in the laptop.

Table 4. Intel HD Graphics drivers

Before installation After installation

Realtek HD audio drivers

Verify if the Realtek audio drivers are already installed in the laptop.

Table 5. Realtek HD audio drivers

Before installation After installation

System Setup

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing F2 key

• Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation keys

The following table displays the system setup navigation keys.

NOTE: For most of the System Setup options, changes that you make are recorded but do not take

effect until you restart the system.

Table 6. Navigation keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

Tab Moves to the next focus area.

Keys Navigation

NOTE: For the standard graphics browser only.

Esc Moves to the previous page till you view the main screen. Pressing Esc in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

F1 Displays the System Setup help file.

System setup options

NOTE: Depending on the computer and its installed devices, the items listed in this section may or

may not appear.

General screen options

This section lists the primary hardware features of your computer.

Option Description

System

Information

This section lists the primary hardware features of your computer.

• System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership

Tag, Ownership Date, Manufacture Date, and the Express Service Code.

• Memory Information: Displays Memory Installed, Memory Available, Memory

Speed, Memory Channels Mode, Memory technology

• Processor Information: Displays Processor Type, Core Count, Processor ID,

Current Clock Speed, Minimum Clock Speed, Maximum Clock Speed,

Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-bit technology.

• Device Information: SATA-0, M.2 PCIe SSD-0, Video Controller, Video BIOS

Version, Video Memory, Panel Type, Native Resolution, Audio Controller, WiFi

Device, WiGig Device, Cellular Device, Bluetooth Device.

Battery

Information

Displays the battery status and the type of AC adapter connected to the computer.

Boot Sequence Allows you to change the order in which the computer attempts to find an

operating system.

• Windows Boot Manager or UEFI

• Legacy or UEFI

Boot Options This option allows you the legacy option ROMs to load. By default, the Enable UEFI

Network Stack is disabled.

Date/Time Allows you to change the date and time.

System Configuration screen options

Option Description

SATA Operation Allows you to configure the internal SATA hard-drive controller. The options are:

• Disabled

• AHCI

• RAID On: This option is enabled by default.

Drives Allows you to configure the SATA drives on board. All drives are enabled by default.

The options are:

• SATA-1

• M.2 PCI-e SSD-0

SMART Reporting This field controls whether hard drive errors for integrated drives are reported

during system startup. This technology is part of the SMART (Self Monitoring

Analysis and Reporting Technology) specification. This option is disabled by default.

• Enable SMART Reporting

USB/Thunderbolt

Configuration This is an optional feature.

This field configures the integrated USB controller. If Boot Support is enabled, the

system is allowed to boot any type of USB Mass Storage Devices (HDD, memory

key, floppy).

If USB port is enabled, device attached to this port is enabled and available for OS.

If USB port is disabled, the OS cannot see any device attached to this port.

The options are:

• Enable USB Boot Support (by default enable)

• Enable External USB Port (by default enable)

• Enable Thunderbolt Port (by default enable).

• Enable Thunderbolt Boot Support. This is an optional feature.

• Always Allows Dell Docks. This is an optional feature.

• Enables Thunderbolt (and PCIe behind TBT) Pre-boot

NOTE: USB keyboard and mouse always work in the BIOS setup irrespective of

these settings.

USB PowerShare This field configures the USB PowerShare feature behavior. This option allows you

to charge external devices using the stored system battery power through the USB

PowerShare port. By default, the Enable USB PowerShare is disabled.

Audio This field enables or disables the integrated audio controller. By default, the Enable

Audio option is selected. The options are:

Option Description

• Enable Microphone (by default enabled)

• Enable Internal Speaker (by default enabled)

Keyboard

Illumination

This field lets you choose the operating mode of the keyboard illumination feature.

The keyboard brightness level can be set from 0% to 100%. The options are:

• Disabled

• Dim

• Bright (enabled by default)

Keyboard

Backlight Timeout

on AC

This feature defines the time-out value for the keyboard backlight when an AC

adapter is plugged into the system. The main keyboard illumination feature is not

affected. Keyboard Illumination will continue to support the various illumination

levels. This field has an effect when the backlight is enabled. Options are:

• 5 seconds

• 10 seconds — this option is selected by default

• 15 seconds

• 30 seconds

• 1 minute

• 5 minute

• 15 minute

• never

Keyboard

Backlight Time-

out on Battery

The Keyboard Backlight Time-out dims out with Battery option. The main keyboard

illumination feature is not affected. Keyboard Illumination will continue to support

the various illumination levels. This field has an effect when the backlight is

enabled. Options are:

• 5 seconds

• 10 seconds — this option is selected by default

• 15 seconds

• 30 seconds

• 1 minute

• 5 minute

• 15 minute

• never

Touchscreen This field controls whether the touchscreen is enabled or disabled. By default, the

option is enabled.

Unobtrusive Mode This option, when enabled, pressing Fn+F7 turns off all light and sound emissions

in the system. To resume normal operation, press Fn+F7 again. This option is

disabled by default.

Miscellaneous

Devices

Allows you to enable or disable various on board devices:

• Enable Camera —enabled by default

Option Description

• Enable Secure Digital(SD) Card

• Secure Digital(SD) Card read only mode

Video screen options

Option Description

LCD Brightness Allows you to set the display brightness depending up on the power source (On

Battery and On AC).

NOTE: The video setting will be visible only when a video card is installed into the system.

Security screen options

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin) password.

NOTE: You must set the admin password before you set the system or hard

drive password. Deleting the admin password automatically deletes the system

password and the hard drive password.

NOTE: Successful password changes take effect immediately.

Default setting: Not set

System Password Allows you to set, change, or delete the system password.

NOTE: Successful password changes take effect immediately.

Default setting: Not set

Mini Card SSD-0

Password

Allows you to set, change or delete the password on the mini card Solid State Drive

(SSD).

NOTE: Successful password changes take effect immediately.

Default setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

NOTE: If Strong Password is enabled, Admin and System passwords must

contain at least one uppercase character, one lowercase character and be at

least 8 characters long.

Password

Configuration

Allows you to determine the minimum and maximum length of Administrator and

System passwords.

Option Description

Password Bypass Allows you to enable or disable the permission to bypass the System and the

Internal HDD password, when they are set. The options are:

• Disabled

• Reboot bypass

Default setting: Disabled

Password Change Allows you to enable the disable permission to the System and Hard Drive

passwords when the admin password is set.

Default setting: Allow Non-Admin Password Changes is selected.

Non-Admin Setup

Changes

Allows you to determine whether changes to the setup options are allowed when

an Administrator Password is set. If disabled the setup options are locked by the

admin password.

UEFI Capsule

Firmware Updates

Allows to control whether this system allows BIOS updates via UEFI capsule update

packages.

Default setting: Enable UEFI Capsule Firmware Updates is selected.

TPM 1.2/2.0

Security

Allows you to enable the Trusted Platform Module (TPM) during POST. The options

are:

• TPM On (enabled by default)

• Clear

• PPI Bypass for Enabled Commands

• PPI Bypass for Disabled Commands

• Activate

• Deactivate

NOTE: To upgrade or downgrade TPM1.2/2.0, download the TPM wrapper

tool (software).

Computrace Allows you to activate or disable the optional Computrace software The options

are:

• Deactivate

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate or disable

the feature and no further changes will be allowed

Default setting: Deactivate

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Enable CPU XD Support (default)

Option Description

OROM Keyboard

Access

Allows you to set an option to enter the Option ROM Configuration screens using

hotkeys during boot. The options are:

• Enabled

• One Time Enable

• Disabled

Default setting: Enabled

Admin Setup

Lockout

Allows you to prevent users from entering Setup when an Administrator password

is set.

Default Setting: Disabled

Secure Boot screen options

Option Description

Secure Boot

Enable

This option enables or disables the Secure Boot feature.

• Disabled

• Enabled

Default setting: Enabled.

Expert Key

Management

Allows you to manipulate the security key databases only if the system is in Custom

Mode. The Enable Custom Mode option is disabled by default. The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx

appear. The options are:

•Save to File—Saves the key to a user-selected file

•Replace from File—Replaces the current key with a key from a user-selected

file

•Append from File—Adds a key to the current database from a user-selected file

•Delete—Deletes the selected key

•Reset All Keys—Resets to default setting

•Delete All Keys—Deletes all the keys

NOTE: If you disable the Custom Mode, all the changes made will be erased

and the keys will restore to default settings.

Intel Software Guard Extensions screen options

Option Description

Intel SGX Enable This field specifies you to provide a secured environment for running code/storing

sensitive information in the context of the main OS. The options are:

• Disabled

• Enabled

Default setting: Disabled

Enclave Memory

Size

This option sets SGX Enclave Reserve Memory Size. The options are:

• 32 MB

• 64 MB

• 128 MB

Performance screen options

Option Description

Multi Core

Support

This field specifies whether the process has one or all cores enabled. The

performance of some applications improves with the additional cores. This option

is enabled by default. Allows you to enable or disable multi-core support for the

processor. The installed processor supports twofour cores. If you enable Multi Core

Support, twofour cores are enabled. If you disable Multi Core Support, one core is

enabled.

• Enable Multi Core Support

Default setting: The option is enabled.

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.

• Enable Intel SpeedStep

Default setting: The option is enabled.

C-States Control Allows you to enable or disable the additional processor sleep states.

• C states

Default setting: The option is enabled.

Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.

• Enable Intel TurboBoost

Option Description

Default setting: The option is enabled.

Hyper-Thread

Control

Allows you to enable or disable the Hyper-Threading in the processor.

• Disabled

• Enabled

Default setting: Enabled.

DDR Frequency This option changes DDR frequency to 1600 or 1866 MHz. By default, 1600 is

selected.

Power Management screen options

Option Description

AC Behavior Allows you to enable or disable the computer from turning on automatically when

an AC adapter is connected.

Default setting: Wake on AC is not selected.

Auto On Time Allows you to set the time at which the computer must turn on automatically. The

options are:

• Disabled

• Every Day

• Weekdays

• Select Days

Default setting: Disabled

USB Wake

Support

Allows you to enable USB devices to wake the system from Standby.

NOTE: This feature is only functional when the AC power adapter is

connected. If the AC power adapter is removed during Standby, the system

setup removes power from all the USB ports to conserve battery power.

• Enable USB Wake Support

• Wake on Trinity Dock - The option is selected by default.

Wake on LAN/

WLAN

Allows you to enable or disable the feature that powers on the computer from the

Off state when triggered by a LAN signal.

• Disabled

• WLAN Only

Default setting: Disabled

Option Description

Peak Shift This option enables you to minimize the AC power consumption during the peak

power times of day. After you enable this option, your system runs only in battery

even if the AC is attached.

• Enable Peak Shift

Default setting: Disabled

Advanced Battery

Charge

Configuration

This option enables you to maximize the battery health. By enabling this option,

your system uses the standard charging algorithm and other techniques, during the

non-work hours to improve the battery health.

• Enabled Advanced Battery Charge Mode

Default setting: Disabled

Primary Battery

Charge

Configuration

Allows you to select the charging mode for the battery. The options are:

• Adaptive

• Standard — Fully charges your battery at a standard rate.

• ExpressCharge — The battery charges over a shorter period of time using Dell’s

fast charging technology. This option is enabled by default.

• Primarily AC use

• Custom

If Custom Charge is selected, you can also configure Custom Charge Start and

Custom Charge Stop.

NOTE: All charging mode may not be available for all the batteries. To enable

this option, disable the Advanced Battery Charge Configuration option.

POST Behavior screen options

Option Description

Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when

you use certain power adapters.

Default setting: Enable Adapter Warnings

Keypad

(Embedded)

Allows you to choose one of two methods to enable the keypad that is embedded

in the internal keyboard.

• Fn Key Only: This option is enabled by default.

• By Numlock

NOTE: When setup is running, this option has no effect. Setup works in Fn Key

Only mode.

Numlock Enable Allows you to enable the Numlock option when the computer boots.

Option Description

Enable Network. This option is enabled by default.

Fn Key Emulation Allows you to set the option where the Scroll Lock key is used to simulate the Fn

key feature.

Enable Fn Key Emulation (default)

Fn Lock Options Allows you to let hot key combinations Fn + Esc toggle the primary behavior of F1–

F12, between their standard and secondary functions. If you disable this option, you

cannot toggle dynamically the primary behavior of these keys. The available

options are:

• Fn Lock. This option is selected by default.

• Lock Mode Disable/Standard

• Lock Mode Enable/Secondary

MEBx Hotkey Allows you to specify whether the MEBx Hotkey function should enable, during the

system boot.

Default Setting: Enable MEBx Hotkey

Fastboot Allows you to speed up the boot process by bypassing some of the compatibility

steps. The options are:

• Minimal

• Thorough (default)

• Auto

Extended BIOS

POST Time

Allows you to create an additional preboot delay. The options are:

• 0 seconds. This option is enabled by default.

• 5 seconds

• 10 seconds

Virtualization support screen options

Option Description

Virtualization Allows you to enable or disable the Intel Virtualization Technology.

Enable Intel Virtualization Technology (default).

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional

hardware capabilities provided by Intel® Virtualization technology for direct I/O.

Enable VT for Direct I/O - enabled by default.

Trusted Execution This option specifies whether a Measured Virtual Machine Monitor (MVMM) can

utilize the additional hardware capabilities provided by Intel Trusted Execution

Option Description

Technology. The TPM Virtualization Technology, and Virtualization technology for

direct I/O must be enabled to use this feature.

Trusted Execution - disabled by default.

Wireless screen options

Option Description

Wireless Switch Allows to set the wireless devices that can be controlled by the wireless switch. The

options are:

• WWAN

• GPS (on WWAN Module)

• WLAN/WiGig

• Bluetooth

All the options are enabled by default.

NOTE: For WLAN and WiGig enable or disable controls are tied together and

they cannot be enabled or disabled independently.

Wireless Device

Enable

Allows you to enable or disable the internal wireless devices.

• WWAN/GPS

• WLAN/WiGig

• Bluetooth

All the options are enabled by default.

Maintenance screen options

Option Description

Service Tag Displays the Service Tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option

is not set by default.

BIOS Downgrade This controls flashing of the system firmware to previous revisions.

Data Wipe This field allows users to erase the data securely from all internal storage devices.

The following is the device affected:

• Internal M.2 SDD

BIOS Recovery This field allows you to recover from certain corrupted BIOS conditions from a

recover file on the user primary hard drive or an external USB key.

Option Description

• BIOS Recovery from Hard Drive (enabled by default)

System Log screen options

Option Description

BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.

Thermal Events Allows you to view and clear the System Setup (Thermal) events.

Power Events Allows you to view and clear the System Setup (Power) events.

Updating the BIOS

It is recommended to update your BIOS (System Setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Restart the computer.

2. Go to Dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below window,

click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If

you want to update the BIOS from 1.0 to 7.0, then install version 4.0 first and then install version 7.0.

System and setup password

You can create a system password and a setup password to secure your computer.

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a system password and setup password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are

deleted and you need not provide the system password to log on to the computer.

To enter the system setup, press F2 immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press Enter or Tab.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press Enter or Tab.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press Esc and a message prompts you to save the changes.

8. Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system and/or setup password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press F2 immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer reboots.

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for

technical assistance. The purpose of running diagnostics is to test your computer's hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Enhanced Pre-Boot System Assessment (ePSA)

diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Device status lights

Table 7. Device status lights

Icon Name Description

Power

status

light

Turns on when you turn on the computer and blinks when the computer is in a

power management mode.

This can be useful as a diagnostic tool when there's a possible failure to the system.

NOTE: The position of the power status light may vary depending on the system.

Technical specifications

NOTE: Offerings may vary by region. For more information regarding the configuration of your

computer in:

• Windows 10, click or tap Start → Settings → System → About.

• Windows 8.1 and Windows 8, click or tap Start → PC Settings → PC and devices → PC

Info.

• Windows 7, click Start , right-click My Computer, and then select Properties.

System specifications

Feature Specification

Chipset Skylake

DRAM bus width 64-bit

Flash EPROM SPI 128 Mbits

PCIe bus 100 MHz

External Bus

Frequency

DMI 3.0 (8GT/s)

Processor specifications

Feature Specification

Types Intel Core m3 / m5 / m7

Intel Smart Cache 3 MB and 4 MB

Memory specifications

Feature Specification

Memory type LPDDR3

Minimum memory 4 GB

Maximum memory 16 GB

Audio specifications

Feature Specification

Types Four-channel high-definition audio

Controller Realtek ALC3246

Stereo conversion 24-bit (analog-to-digital and digital-to-analog)

Internal interface High-definition audio

External interface Microphone-in, stereo headphones, and headset combo connector

Speakers Two

Internal speaker

amplifier

2 W (RMS) per channel

Volume controls Hot keys

Video specifications

Feature Specification

Type Integrated on system board

UMA controller Intel HD Graphics 515

External display

support

One micro-HDMI

Camera specifications

Feature Specification

HD Panel

Resolution

1280 x 720 pixels (Non Touch)

Video Resolution

(maximum)

1280 x 720 pixels

Diagonal viewing

angle

74°

Communication specifications

Features Specification

Wireless Internal wireless local area network (WLAN) and wireless wide area network

(WWAN)

Features Specification

• Bluetooth 4.1 LE

Port and connector specifications

Feature Specification

Audio One microphone/stereo headphone/speakers connector

Video Micro HDMI

USB • one USB3.0 with PowerShare

• two type C ports with thunderbolt 3 support

Memory card

reader (Micro SD)

One

Micro Subscriber

Identity Module

(uSIM) card

One

Smart Card Optional

RFID Optional

Finger print reader Optional

Display specifications

Feature Specification

FHD anti-glare:

Height 293.76 mm (11.57 inches)

Width 165.24 mm (6.51 inches)

Diagonal 337.82 (13.3 inches)

Maximum

resolution

1920 x 1080

Refresh rate 60 Hz

Maximum viewing

angles (horizontal)

+/-80°

Maximum viewing

angles (vertical)

+/-80°

Pixel pitch 0.153 mm

QHD anti-glare:

Height 293.76 mm (11.57 inches)

Feature Specification

Width 165.24 mm (6.51 inches)

Diagonal 337.82 (13.3 inches)

Maximum

resolution

3200 x 1800

Refresh rate 60 Hz

Maximum viewing

angles (horizontal)

+/-80°

Maximum viewing

angles (vertical)

+/-80°

Pixel pitch 0.092 mm

Keyboard specifications

Feature Specification

Number of keys • United States: 82 keys

• United Kingdom: 83 keys

• Brazil: 84 keys

• Japan: 86 keys

Touchpad specifications

Feature Specification

Active Area:

X-axis 99.50 mm

Y-axis 51.00 mm53.00 mm

Battery specifications

Feature Specification

Type • 34 WHr (4 cell) Entry

• 43 WHr (4 cell) Upsell

34 WHr (4 cell)

Entry:

Length 267 mm (10.5 inches)

Height 4.35 mm (0.17 inch)

Feature Specification

Width 58.5 mm (2.3 inches)

Weight 165.0 g (0.43 lb)

Voltage 7.6 VDC

43 WHr (4 cell)

Upsell:

Length 267 mm (10.5 inches)

Height 6.25 mm (0.24 inch)

Width 58.5 mm (2.3 inches)

Weight 200 g (0.66 lb)

Voltage 7.6 VDC

Temperature

range:

Operating • Charge: 0°C to 50°C (32°F to 122°F)

• Discharge: 0°C to 70°C (32°F to 158°F)

Non-operating - 20°C to 65°C (- 4°F to 149°F)

Coin cell battery 3 V CR2032 lithium coin cell

AC Adapter specifications

Feature Specification

Type 45 W (Type C)

Input voltage 100 VAC to 240 VAC

Input current

(maximum)

1.3A

Input frequency 50 Hz to 60 Hz

Output power 45 W

Output current 2.25 A

Rated output

voltage

20 VDC

Weight 0.17 kg (.37 lb)

Dimensions 0.87 x 2.17 x 3.42

Temperature range

(Operating)

0°C to 40°C (32°F to 104°F)

Feature Specification

Temperature range

(Non-Operating)

–40°C to 70°C (–40°F to 158°F)

Physical specifications

Feature Specification

Front height 9.86 mm (0.39 inches)

Back height 14.32 mm (0.56 inches)

Width 304.8 mm (12 inches)

Depth 210.5 mm (8.29 inches)

Minimum Weight

(Non-touch with

34Whr battery)

1.12 kg (2.48 lb)

Environmental specifications

Temperature Specifications

Operating 0 °C to 60 °C (32 °F to 140 °F)

Storage –51 °C to 71 °C (–59 °F to 159 °F)

Relative

humidity

(maximum)

Specifications

Operating 10 % to 90 % (non condensing)

Storage 5 % to 95 % (non condensing)

Altitude

(maximum) Specifications

Operating –15.2 m to 3048 m (–50 to 10,000 ft)

0° to 35°C

Non-operating –15.24 m to 10,668 m (–50 ft to 35,000 ft)

Airborne

contaminant level

G2 or lower as defined by ISA S71.04–1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Go to Dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the

page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL 13 User Manual

Related Manuals