Table of Contents
- Dell Latitude 3301 Service Manual
- Working on your computer
- Technology and components
- Removing and installing components
- Recommended tools
- Screw list
- Disassembly and reassembly
- Base cover
- Battery
- Coin-cell battery
- Solid-state drive
- Heat sink
- Fan
- Speakers
- WLAN card
- WWAN card
- Touchpad
- Power-adapter port
- Display assembly
- I/O board
- Power-button board
- Power button with fingerprint reader
- System board
- Display bezel
- Display panel
- Display hinges
- Camera
- Display back-cover
- Display cable
- Palm-rest and keyboard assembly
- Troubleshooting
- Getting help
DELL 3301 User Manual
Displayed below is the user manual for 3301 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Latitude 3301
Service Manual
Regulatory Model: P114G
Regulatory Type: P114G001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2019 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2019 - 05
Rev. A00
Contents
1 Working on your computer............................................................................................................................. 5
Safety instructions............................................................................................................................................................. 5
Turning o your computer — Windows 10.....................................................................................................................5
Before working inside your computer..............................................................................................................................6
After working inside your computer.................................................................................................................................6
2 Technology and components..........................................................................................................................7
LPDDR3...............................................................................................................................................................................7
Memory Errors..............................................................................................................................................................7
HDMI 1.4- HDMI 2.0........................................................................................................................................................... 7
HDMI 1.4- HDMI 2.0 Features.....................................................................................................................................7
Advantages of HDMI................................................................................................................................................... 8
USB features.......................................................................................................................................................................8
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)............................................................................................................. 8
Speed.............................................................................................................................................................................9
Applications...................................................................................................................................................................9
Compatibility................................................................................................................................................................10
Intel Optane memory........................................................................................................................................................10
Enabling Intel Optane memory..................................................................................................................................10
Disabling Intel Optane memory.................................................................................................................................. 11
3 Removing and installing components............................................................................................................12
Recommended tools.........................................................................................................................................................12
Screw list........................................................................................................................................................................... 12
Disassembly and reassembly........................................................................................................................................... 14
Base cover...................................................................................................................................................................14
Battery......................................................................................................................................................................... 16
Coin-cell battery..........................................................................................................................................................18
Solid-state drive......................................................................................................................................................... 20
Heat sink..................................................................................................................................................................... 23
Fan............................................................................................................................................................................... 25
Speakers......................................................................................................................................................................27
WLAN card................................................................................................................................................................. 29
WWAN card.................................................................................................................................................................31
Touchpad.....................................................................................................................................................................33
Power-adapter port................................................................................................................................................... 35
Display assembly.........................................................................................................................................................37
I/O board..................................................................................................................................................................... 41
Power-button board.................................................................................................................................................. 44
Power button with ngerprint reader......................................................................................................................45
System board..............................................................................................................................................................47
Display bezel............................................................................................................................................................... 50
Display panel...............................................................................................................................................................52
Contents 3
Display hinges............................................................................................................................................................. 57
Camera........................................................................................................................................................................58
Display back-cover.....................................................................................................................................................60
Display cable............................................................................................................................................................... 62
Palm-rest and keyboard assembly........................................................................................................................... 63
4 Troubleshooting........................................................................................................................................... 66
Enhanced Pre-Boot System Assessment (ePSA) diagnostics...................................................................................66
Running the ePSA diagnostics.................................................................................................................................66
System diagnostic lights................................................................................................................................................. 66
Flashing BIOS (USB key)................................................................................................................................................ 67
Flashing the BIOS............................................................................................................................................................ 68
Backup media and recovery options..............................................................................................................................68
WiFi power cycle..............................................................................................................................................................68
Flea power release........................................................................................................................................................... 68
5 Getting help.................................................................................................................................................69
Contacting Dell.................................................................................................................................................................69
4 Contents
Working on your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
CAUTION: System will shut down if side covers are removed while the system is running. The system will not power on if the side
cover is removed.
CAUTION: System will shut down if side covers are removed while the system is running. The system will not power on if the side
cover is removed.
CAUTION: System will shut down if side covers are removed while the system is running. The system will not power on if the side
cover is removed.
Turning o your computer — Windows 10
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer or
remove the side cover.
1 Click or tap .
2 Click or tap and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds
to turn them o.
1
Working on your computer 5
Before working inside your computer
NOTE: The images in this document may dier from your computer depending on the conguration you ordered.
After working inside your computer
CAUTION: Leaving stray or loose screws inside your computer may severely damage your computer.
1 Replace all screws and ensure that no stray screws remain inside your computer.
2 Connect any external devices, peripherals, or cables you removed before working on your computer.
3 Replace any media cards, discs, or any other parts that you removed before working on your computer.
4 Connect your computer and all attached devices to their electrical outlets.
5 Turn on your computer.
6 Working on your computer
Technology and components
NOTE: Instructions provided in this section are applicable on computers shipped with Windows 10 operating system. Windows 10
is factory-installed with this computer.
Topics:
• LPDDR3
• HDMI 1.4- HDMI 2.0
• USB features
• Intel Optane memory
LPDDR3
LPDDR3 (double data rate third generation low voltage) memory is a higher-speed successor to the DDR2 and DDR3 technologies and
allows up to 512 GB in capacity, compared to the DDR3's maximum of 128 GB per DIMM.
LPDDR3 needs 20 percent less or just 1.35 volts, compared to DDR3 which requires 1.5 volts of electrical power to operate. LPDDR3 also
supports a new, deep power-down mode that allows the host device to go into standby without needing to refresh its memory. Deep
power-down mode is expected to reduce standby power consumption by 40 to 50 percent.
Memory Errors
Memory errors on the system display the new ON-FLASH-FLASH or ON-FLASH-ON failure code. If all memory fails, the LCD does not
turn on. Troubleshoot for possible memory failure by trying known good memory modules in the memory connectors on the bottom of the
system or under the keyboard, as in some portable systems.
NOTE: The LPDDR3 memory is imbedded in board and not a replaceable DIMM as shown and referred.
HDMI 1.4- HDMI 2.0
This topic explains the HDMI 1.4/2.0 and its features along with the advantages.
HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on
a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
HDMI 1.4- HDMI 2.0 Features
•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,
eliminating the need for a separate audio cable
2
Technology and components 7
•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems
used in many commercial movie theaters
•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of
the motoring environment while delivering true HD quality
Advantages of HDMI
• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-eective manner
• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral
devices like mice, keyboards, external drivers, and printers.
Let's take a quick look on the USB evolution referencing to the table below.
Table 1. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 2.0 480 Mbps High Speed 2000
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 3.1 Gen 2 10 Gbps Super Speed 2013
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
• Higher transfer rates (up to 5 Gbps)
• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
• New power management features
• Full-duplex data transfers and support for new transfer types
• Backward USB 2.0 compatibility
• New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
8Technology and components
Speed
Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs
of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel
count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps
theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB
3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this
speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
• USB 3.0/USB 3.1 Gen 1 Solid-state Drives
Technology and components 9
• USB 3.0/USB 3.1 Gen 1 RAIDs
• Optical Media Drives
• Multimedia Devices
• Networking
• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Windows 10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
Intel Optane memory
Intel Optane memory functions only as a storage accelerator. It neither replaces nor adds to the memory (RAM) installed on your computer.
NOTE: Intel Optane memory is supported on computers that meet the following requirements:
• 7th Generation or higher Intel Core i3/i5/i7 processor
• Windows 10 64-bit version 1607 or higher
• Intel Rapid Storage Technology driver version 15.9.1.1018 or higher
Table 2. Intel Optane memory specications
Feature Specications
Interface PCIe 3x2 NVMe 1.1
Connector M.2 card slot (2230/2280)
Congurations supported • 7th Generation or higher Intel Core i3/i5/i7 processor
• Windows 10 64-bit version 1607 or higher
• Intel Rapid Storage Technology driver version 15.9.1.1018 or
higher
Capacity 16 GB
Enabling Intel Optane memory
1 On the taskbar, click the search box, and type "Intel Rapid Storage Technology".
2 Click Intel Rapid Storage Technology.
3 On the Status tab, click Enable to enable the Intel Optane memory.
4 On the warning screen, select a compatible fast drive, and then click Yes to continue enabling Intel Optane memory.
5 Click Intel Optane memory > Reboot to enable the Intel Optane memory.
NOTE: Applications may take up to three subsequent launches after enablement to see the full performance benets.
10 Technology and components
Disabling Intel Optane memory
CAUTION: After disabling Intel Optane memory, do not uninstall the driver for Intel Rapid Storage Technology as it will result in a
blue screen error. The Intel Rapid Storage Technology user interface can be removed without uninstalling the driver.
NOTE: Disabling Intel Optane memory is required before removing the SATA storage device, accelerated by the Intel Optane
memory module, from the computer.
1 On the taskbar, click the search box, and then type "Intel Rapid Storage Technology".
2 Click Intel Rapid Storage Technology. The Intel Rapid Storage Technology window is displayed.
3 On the Intel Optane memory tab, click Disable to disable the Intel Optane memory.
4 Click Yes if you accept the warning.
The disabling progress is displayed.
5 Click Reboot to complete disabling Intel Optane memory and restart your computer.
Technology and components 11
Removing and installing components
Recommended tools
The procedures in this document require the following tools:
• Phillips #0 screwdriver
• Phillips #1 screwdriver
• Philips #2 screwdriver
• Plastic scribe
• T-30 torx screwdriver
NOTE: The #0 screw driver is for screws 0-1 and the #1 screw driver is for screws 2-4
Screw list
NOTE: When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and then
place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is restored when
the component is replaced.
NOTE: Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surface when replacing a
component.
3
12 Removing and installing components
NOTE: Screw color may vary with the conguration ordered.
Table 3. Screw list
Component Secured to Screw type Quantity Screw image
Base cover Palm rest and keyboard
assembly
M2x6
Captive screws
4
3
NOTE: Screw color
may vary depending
on the conguration
ordered.
Battery Palm rest and keyboard
assembly
M2x3 4
Battery Palm rest and keyboard
assembly
M1.6x4 1
Fan Palm rest and keyboard
assembly
M2x3 2
WLAN Card WLAN Card bracket M2x2.5 1
WWAN Card WWAN Card bracket M2x2.5 1
Touchpad Palm-rest keyboard
assembly.
M1.6x2 5
M.2 2230/2280 Solid
State Drive
Palm rest and keyboard
assembly
M2x2.5 1
Heat sink System board Captive screws 7
Hinges Palm rest and keyboard
assembly
M2.5x3.5 2
Hinge brackets Display back-cover and
antenna assembly
M2.5x3.5 1
Hinge brackets Display back-cover and
antenna assembly
M2x2 2
I/O board Palm rest and keyboard
assembly
M2.5x3.5 2
I/O board Palm rest and keyboard
assembly
M2x3 1
USB Type-C port bracket System board M2.5x3.5 1
Power-adapter port Palm rest and keyboard
assembly
M2x3 1
Power-button board Palm rest and keyboard
assembly
M2x2 1
Power button with
ngerprint reader
(optional)
Palm rest and keyboard
assembly
M2x2 1
System board Palm rest and keyboard
assembly
M2x4 2
Wireless-card bracket System board M2x3 1 Removing and installing components 13
Disassembly and reassembly
Base cover
Removing the base cover
1 Follow the procedure in Before working inside your computer.
The following image indicates the location of the base cover and provides a visual representation of the removal procedure.
1 Loosen the three captive screws on the base cover.
2 Remove the four screws (M2x6) that secure the base cover to the palm-rest and keyboard assembly.
3 Pry the base cover starting from the top-left corner of the palm-rest and keyboard assembly.
4 Lift the base cover o the palm-rest and keyboard assembly.
Installing the base cover
If you are replacing a component, remove the existing component before performing the installation procedure.
14 Removing and installing components
The following image indicates the location of the base cover and provides a visual representation of the installation procedure.
1 Place the computer with the hinges facing towards you.
2 Align the base cover on the palm-rest and keyboard assembly, and snap the base cover into place.
3 Replace the four screws (M2x6) that secure the base cover to the palm-rest and keyboard assembly.
4 Tighten the three captive screws that secure the base cover to the palm-rest and keyboard assembly.
1 Follow the procedure in After working inside your computer.
Removing and installing components 15
Battery
Lithium-ion battery precautions
CAUTION:
• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting the AC adapter
from the system to allow the battery to drain.
• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
• Ensure any screws during the servicing of this product are not lost or misplaced, to prevent accidental puncture or damage to the
battery and other system components.
• If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a Lithium-ion
battery can be dangerous. In such an instance, contact for assistance and further instructions.
• If the battery gets stuck inside your computer as a result of swelling, do not try to release it as puncturing, bending, or crushing a
lithium-ion battery can be dangerous. In such an instance, contact Dell technical support for assistance. See https://www.dell.com/
support.
• Always purchase genuine batteries from https://www.dell.com or authorized Dell partners and resellers.
Removing the battery
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
The following image indicates the location of the battery and provides a visual representation of the removal procedure.
16 Removing and installing components
1 Disconnect the battery cable from the system board.
2 Remove the four screws (M2x2) that secure the battery to the palm-rest and keyboard assembly.
3 Remove the screw (M1.6x4) that secures the battery to the system board and palm-rest and keyboard assembly.
4 Lift the battery o the palm-rest and keyboard assembly.
Installing the battery
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of the battery and provides a visual representation of the installation procedure.
Removing and installing components 17
1 Connect the battery cable to the system board.
2 Replace the four screws (M2x2) that secure the battery to the palm-rest and keyboard assembly.
3 Replace the screw (M1.6x4) that secures the battery to the system board and palm-rest and keyboard assembly.
1 Install the base cover.
2 Follow the procedure in After working inside your computer.
Coin-cell battery
Removing the coin-cell battery
1 Follow the procedure in Before working inside your computer.
CAUTION: Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended that
you note the BIOS setup program’s settings before removing the coin-cell battery.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of the coin-cell battery and provides a visual representation of the removal procedure.
18 Removing and installing components
1 Disconnect the coin-cell battery cable from the system board.
2 Remove the coin-cell battery cable from the routing guide.
3 Peel the coin-cell battery o the palm-rest and keyboard assembly.
Installing the coin-cell battery
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of the coin-cell battery and provides a visual representation of the installation procedure.
1 Adhere the coin-cell battery to the slot on the palm-rest and keyboard assembly.
2 Route the coin-cell battery cable through the routing guide.
Removing and installing components 19
3 Connect the coin-cell battery cable to the system board.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Solid-state drive
Removing the M.2 2280 solid-state drive
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.
1 Remove the screw (M2x2.5) that secures the solid-state drive to the system board.
2 Slide and remove the solid-state drive o the solid-state drive slot on the system board.
Installing the M.2 2280 solid-state drive
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure.
20 Removing and installing components
1 Align the notch on the solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive
slot on the system board.
2 Replace the screw (M2x2.5) that secures the solid-state drive to the system board.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Removing the M.2 2230 solid-state drive
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of the solid-state drive and provides a visual representation of the removal procedure.
Removing and installing components 21
1 Remove the screw (M2x2.5) that secures the solid-state drive bracket to the system board.
2 Slide and remove the solid-state drive bracket o the solid-state drive on the system board.
3 Slide and remove the solid-state drive o the solid-state drive slot on the system board.
Installing the M.2 2230 solid-state drive
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure.
22 Removing and installing components
1 Align the notch on the solid-state drive with the tab on the solid-state drive slot and slide the solid-state drive into the solid-state drive
slot on the system board.
2 Slide the solid-state bracket on to the solid-state drive on the system board.
3 Replace the screw (M2x2.5) that secures the solid-state drive to the system board.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Heat sink
Removing the heat sink
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of the heat sink and provides a visual representation of the removal procedure.
Removing and installing components 23
1 Peel the tape that secures the heat sink to the system board.
2 In the reverse sequential order (7>6>5>4>3>2>1), loosen the seven captive screws that secure the heat sink to the system board.
3 Lift the heat sink o the system board.
Installing the heat sink
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of the base cover and provides a visual representation of the installation procedure.
24 Removing and installing components
1 Align and place the screw holes on the heat sink with the screw holes on the system board.
2 In sequential order (as indicated on the heat sink), tighten the seven captive screws that secure the heat sink to the system board.
3 Adhere the tape that secures the heat sink to the system board.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Fan
Removing the fan
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of fan and provides a visual representation of the removal procedure.
Removing and installing components 25
1 Disconnect the I/O-board cable from the system board and I/O board.
NOTE: This step is only applicable for computers shipped with a WWAN conguration.
2 Remove the two (M2x3) screws that secure the fan to the system board.
3 Lift the fan slightly o the palm-rest and keyboard assembly.
4 Disconnect the fan cable from the system board and completely lift the fan o the palm-rest and keyboard assembly.
Installing the fan
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of fan and provides a visual representation of the installation procedure.
26 Removing and installing components
1 Connect the fan cable to the system board.
2 Align the screw holes on the fan with the screw holes on the palm-rest and keyboard assembly.
3 Replace the two (M2x3) screws that secure the fan to the palm-rest and keyboard assembly.
4 Connect the I/O-board cable to the system board and I/O board.
NOTE: This step is only applicable for computers shipped with a WWAN conguration.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Speakers
Removing the speakers
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
Removing and installing components 27
3 Remove the battery.
The following image indicates the location of speakers and provides a visual representation of the removal procedure.
1 Open the latch and disconnect the touchpad cable from the system board.
2 Disconnect the speaker cable from the system board.
3 Peel the tapes that secure the speaker cable to the palm-rest and keyboard assembly.
4 Note the routing of the speaker cable and remove the speaker cable from the routing guides on the palm-rest and keyboard assembly.
NOTE: Note the position of the rubber grommets before lifting the speakers.
5 Lift the speakers, along with the cable, o the palm-rest and keyboard assembly.
Installing the speakers
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of speakers and provides a visual representation of the installation procedure.
28 Removing and installing components
1 Using the alignment posts and rubber grommets, place the speakers in the slots on the palm-rest and keyboard assembly.
2 Route the speaker cable through the routing guides on the palm-rest and keyboard assembly.
3 Adhere the tapes that secure the speaker cable to the palm-rest and keyboard assembly.
4 Connect the speaker cable to the system board.
5 Connect the touchpad cable to the system board and close the latch to secure the cable.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
WLAN card
Removing the WLAN card
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
Removing and installing components 29
3 Remove the battery.
The following image indicates the location of WLAN card and provides a visual representation of the removal procedure.
1 Remove the screw (M2x2.5) that secures the WLAN-card bracket to the WLAN card and lift the WLAN-card bracket o the WLAN
card.
2 Disconnect the antenna cables from the WLAN card.
3 Slide and remove the WLAN card from the WLAN-card slot.
Installing the WLAN card
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of WLAN card and provides a visual representation of the installation procedure.
30 Removing and installing components
1 Connect the antenna cables to the WLAN card.
2 Align the notch on the WLAN card with the tab on the WLAN card slot and insert the WLAN card at an angle into the WLAN card slot.
3 Align and place the WLAN card bracket on the WLAN card.
4 Replace the screw (M2x2.5) to secure the WLAN card bracket to the WLAN card.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
WWAN card
Removing the WWAN card
NOTE: This procedure is only applicable for computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of WWAN card and provides a visual representation of the removal procedure.
Removing and installing components 31
1 Remove the screw (M2x2.5) that secures the WWAN card bracket to the WWAN card.
2 Note the alignment of the WWAN-card bracket before lifting it o the WWAN card.
3 Disconnect the antenna cables from the WWAN card.
4 Slide and remove the WWAN card from the WWAN card slot.
Installing the WWAN card
NOTE: This procedure is only applicable for computers shipped with a WWAN conguration.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of WWAN card and provides a visual representation of the installation procedure.
32 Removing and installing components
1 Align the notch on the WWAN card with the tab on the WWAN-card slot and insert the WWAN card at an angle into the WWAN-card
slot.
2 Connect the antenna cables to the WWAN card and align the WWAN-card bracket on the WWAN card.
3 Replace the screw (M2x2.5) that secures the WWAN bracket to the WWAN card.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Touchpad
Removing the touchpad
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of touchpad and provides a visual representation of the removal procedure.
Removing and installing components 33
1 Peel the tapes that secure the touchpad to the palm-rest and keyboard assembly.
2 Open the latch and disconnect the touchpad cable from the system board.
3 Remove the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.
4 Lift the touchpad bracket o the palm-rest and keyboard assembly.
5 Remove the two (M1.6x2) screws that secure the touchpad to the palm-rest and keyboard assembly.
6 Lift the touchpad, along with the cable, o the palm-rest and keyboard assembly.
Installing the touchpad
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of touchpad and provides a visual representation of the installation procedure.
34 Removing and installing components
1 Align and place the touchpad into the slot on the palm-rest and keyboard assembly.
2 Replace the two (M1.6x2) screws that secure the touchpad to the palm-rest and keyboard assembly.
3 Align and place the touchpad bracket into the slot on the palm-rest and keyboard assembly.
4 Replace the three (M1.6x2) screws that secure the touchpad bracket to the palm-rest and keyboard assembly.
5 Slide the touchpad cable into its connector on the system board and close the latch to secure the cable.
6 Adhere the tape that secures the touchpad to the palm-rest and keyboard assembly.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Power-adapter port
Removing and installing components 35
Removing the power-adapter port
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of power-adapter port and provides a visual representation of the removal procedure.
1 Remove the screw (M2.5x3.5) that secures the display-cable bracket to the system board.
2 Remove the screw (M2x4) that secures the right display hinge to the system board.
3 Open the display hinges at an angle of 90 degrees.
4 Disconnect the power-adapter port cable from the system board.
5 Remove the screw (M2x3) that secures the power-adapter port to the palm-rest and keyboard assembly.
6 Lift the power-adapter port, along with its cable, o the palm-rest and keyboard assembly.
Installing the power-adapter port
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of power-adapter port and provides a visual representation of the installation procedure.
36 Removing and installing components
1 Connect the power-adapter port cable to the system board.
2 Replace the screw (M2x3) that secures the power-adapter port to the palm-rest and keyboard assembly.
3 Align and place the display-cable bracket on the system board.
4 Replace the screw (M2.5x3.5) that secure the display-cable bracket to the system board.
5 Using the alignment posts, close the display hinges.
6 Replace the screw (M2x4) that secure the right display hinge to the system board.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
Display assembly
Removing the display assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
The following image indicates the location of display assembly and provides a visual representation of the removal procedure.
Removing and installing components 37
38 Removing and installing components
1 Remove the screw (M2.5x3.5) that secures the display-cable bracket to the system board.
2 Lift the display-cable bracket o the system board.
3 Using the pull tab, disconnect the display cable from the system board.
4 Remove the two screws (M2.5x3.5) that secure the left display hinge to the I/O board and palm-rest and keyboard assembly.
5 Remove the screw (M2x4) that secures the right display hinge to the system board.
6 Open the display hinges at an angle of 90 degrees.
7 Remove the palm-rest and keyboard assembly o the display assembly.
Removing and installing components 39
Installing the display assembly
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of display assembly and provides a visual representation of the installation procedure.
40 Removing and installing components
1 Align and place the palm-rest and keyboard assembly on the display assembly.
2 Using the alignment posts, close the display hinges.
3 Replace the two screws (M2.5x3.5) that secures the left display hinge to the I/O board and palm-rest and keyboard assembly.
4 Replace the screw (M2x4) that secures the right display hinge to the system board.
5 Connect the display cable on to the connector on the system board
6 Align and place the display-cable bracket on the display cable.
7 Replace the screw (M2x4) that secures the display-cable bracket to the system board.
1 Install the battery.
2 Install the base cover.
3 Follow the procedure in After working inside your computer.
I/O board
Removing and installing components 41
Removing the I/O board
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the fan.
The following image indicates the location of I/O board and provides a visual representation of the removal procedure.
1 Remove the two screws (M2.5x3.5) that secure the left display hinge to the I/O board and palm-rest and keyboard assembly.
2 Open the display hinges at an angle of 90 degrees.
3 Peel the tape that secures the I/O-board cable to the I/O board.
4 Open the latch and disconnect the I/O-board cable from the I/O board.
5 Remove the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.
6 Lift the I/O board o the palm-rest and keyboard assembly.
42 Removing and installing components
Installing the I/O board
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of I/O board and provides a visual representation of the installation procedure.
1 Align and place the I/O board on the palm-rest and keyboard assembly.
2 Replace the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly.
3 Connect the I/O-board cable to the I/O board and close the latch to secure the cable.
4 Adhere the tape that secures the I/O board to the I/O board.
5 Using the alignment posts, close the display hinges.
6 Replace the two screws (M2.5x3.5) that secure the left display hinge to the I/O board and palm-rest and keyboard assembly.
1 Install the fan.
2 Install the battery.
3 Install the base cover.
Removing and installing components 43
4 Follow the procedure in After working inside your computer.
Power-button board
Removing the power-button board
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the fan.
6 Remove the I/O board.
The following image indicates the location of power button and provides a visual representation of the removal procedure.
1 Remove the screw (M1.6x2) that secures the power-button bracket to the palm-rest and keyboard assembly.
2 Remove the screw (M1.6x2) that secures the power-button board to the palm-rest and keyboard assembly and lift the power-button
board o the palm-rest and keyboard assembly.
Installing the power-button board
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of power-button board and provides a visual representation of the installation procedure.
44 Removing and installing components
1 Align the screw hole on the power-button board with the screw hole on the palm-rest and keyboard assembly.
2 Replace the screw (M1.6x2) that secures the power-button board to the palm-rest and keyboard assembly.
3 Align the screw hole on the power-button bracket with the screw hole on the palm-rest and keyboard assembly.
4 Replace the screw (M1.6x2) that secures the power-button bracket to the palm-rest and keyboard assembly.
1 Install the I/O board.
2 Install the fan.
3 Install the WLAN card.
4 Install the battery.
5 Install the base cover.
6 Follow the procedure in After working inside your computer.
Power button with ngerprint reader
Removing the power button with ngerprint reader
NOTE: This procedure is only applicable for computers shipped with a ngerprint reader.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the fan.
6 Remove the I/O board.
The following image indicates the location of power button with ngerprint reader and provides a visual representation of the removal
procedure.
Removing and installing components 45
1 Remove the screw (M1.6x2) that secures the power-button bracket to the palm-rest and keyboard assembly.
2 Remove the screw (M1.6x2) that secures the power button with ngerprint reader to the palm-rest and keyboard assembly.
3 Open the latch and disconnect the ngerprint-reader cable from the ngerprint-reader board.
4 Lift the power button with ngerprint-reader, along with the power-button cable, o the palm-rest and keyboard assembly.
Installing the power button with ngerprint reader
NOTE: This procedure is only applicable for computers shipped with a ngerprint reader.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of power button with ngerprint reader and provides a visual representation of the installation
procedure.
46 Removing and installing components
1 Align and place the power button with ngerprint reader on the palm-rest and keyboard assembly.
2 Replace the screw (M1.6x2) that secure the power button with ngerprint reader to the palm-rest and keyboard assembly.
3 Connect the ngerprint-reader cable to the ngerprint-reader board and close the latch to secure the cable.
4 Align and place the power-button bracket on the palm-rest and keyboard assembly.
5 Replace the screw (M1.6x2) that secure the power-button bracket to the palm-rest and keyboard assembly.
1 Install the I/O board.
2 Install the fan.
3 Install the WLAN card.
4 Install the battery.
5 Install the base cover.
6 Follow the procedure in After working inside your computer.
System board
Removing the system board
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the M.2 2280 solid-state drive or M,2 2230 solid-state drive, whichever applicable.
5 Remove the WLAN card.
6 Remove the fan.
7 Remove the heat sink.
The following image indicates the location of system board and provides a visual representation of the removal procedure.
Removing and installing components 47
1 Remove the screw (M2x4) screw that secures the right display hinge to the system board.
2 Remove the screw (M2x4) that secures the display-cable bracket to the system board.
3 Remove the screw (M2.5x3.5) screw that secures the USB Type-C port bracket to the system board.
4 Peel the tape that secures the I/O-board cable to the system board.
5 Open the latch and disconnect the I/O-board cable from the system board.
6 Disconnect the speaker cable from the system board.
7 Open the latch and disconnect the ngerprint-reader cable from the system board.
8 Open the latch and disconnect the touchpad cable from the system board.
9 Open the latch and disconnect the keyboard cable from the system board.
10 Open the latch and disconnect the keyboard backlit cable from the system board.
11 Disconnect the coin-cell battery cable from the system board.
12 Disconnect the power-adapter port cable from the system board.
13 Using the pull tab, disconnect the display cable from the system board.
14 Gently release the ports on the system board from the slots on the palm-rest and keyboard assembly and lift the system board o the
palm-rest and keyboard assembly.
48 Removing and installing components
Installing the system board
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of system board and provides a visual representation of the installation procedure.
1 Slide the ports on the system board into the slots on the palm-rest and keyboard assembly and align the screw holes on the system
board with the screw holes on the palm-rest and keyboard assembly.
2 Connect the display cable on to the connector on the system board6
3 Connect the power-adapter port cable to the system board.
4 Connect the coin-cell battery cable to the system board.
5 Connect the keyboard backlit cable to the system board and close the latch to secure the cable.
6 Connect the keyboard cable to the system board and close the latch to secure the cable.
7 Connect the touchpad cable to the system board and close the latch to secure the cable.
8 Connect the ngerprint-reader cable to the system board and close the latch to secure the cable.
9 Connect the speaker cable to the system board.
Removing and installing components 49
10 Connect the I/O-board cable to the system board and close the latch to secure the cable.
11 Adhere the tape that secures the I/O-board cable to the system board.
12 Replace the screw (M2x4) screw that secures the right display hinge to the system board.
13 Replace the screw (M2x4) that secures the display-cable bracket to the system board.
14 Replace the screw (M2.5x3.5) screw that secures the USB Type-C port bracket to the system board.
1 Install the power-adapter port.
2 Install the display assembly.
3 Install the heat sink.
4 Install the fan.
5 Install the WLAN card.
6 Install the M.2 2280 solid-state drive or M.2 2230 solid-state drive, whichever applicable.
7 Install the battery.
8 Install the base cover.
9 Follow the procedure in After working inside your computer.
Display bezel
Removing the display bezel
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the display assembly.
The following image indicates the location of display bezel and provides a visual representation of the removal procedure.
50 Removing and installing components
1 Carefully pry the edges of the display bezel o the display back-cover and antenna assembly.
2 Remove the display bezel o the display back-cover and antenna assembly.
Installing the display bezel
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of display bezel and provides a visual representation of the installation procedure.
Removing and installing components 51
Align the display bezel with the display back-cover and antenna assembly, and gently snap the display bezel into place.
1 Install the display assembly.
2 Install the WLAN card.
3 Install the battery.
4 Install the base cover.
5 Follow the procedure in After working inside your computer.
Display panel
Removing the display panel
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the display assembly.
6 Remove the display bezel.
The following image indicates the location of display panel and provides a visual representation of the removal procedure.
52 Removing and installing components
Removing and installing components 53
1 Using a plastic scribe, slide out the pull tab of the SR tape from both sides of the display panel.
2 Pull out a small section of the SR tape.
3 Roll the SR tape around the plastic scribe.
NOTE: To avoid severing/breaking the SR tape, pull out only a small section of the SR tape and then roll the SR tape
around the scribe.
4 Lift the display panel o the display back-cover.
5 Peel the tape that secures the display cable to the display back-cover.
6 Open the latch and disconnect the display cable from the display back-cover.
54 Removing and installing components
Installing the display panel
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of display panel and provides a visual representation of the installation procedure.
Removing and installing components 55
1 Peel o the transparent protective lms from the SR tapes.
2 Align and adhere both the SR tapes to the plastic edge of the display back-cover.
3 Peel o the blue protective lms from the SR tapes.
4 Starting from the top, align and place the display panel on the display back-cover.
5 Remove the release paper from the pressure lm.
6 Adhere the pressure lm on the display panel.
7 Using the at end of the plastic scribe or handle of the screwdriver, press and roll over the pressure lms until they turn pink.
8 Peel o the pressure lm from the display panel.
9 Place the display bezel on the display back-cover and snap it into place.
1 Install the display bezel.
56 Removing and installing components
2 Install the display assembly.
3 Install the WLAN card.
4 Install the battery.
5 Install the base cover.
6 Follow the procedure in After working inside your computer.
Display hinges
Removing the display hinges
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the display assembly.
6 Remove the display bezel.
The following image indicates the location of display hinges and provides a visual representation of the removal procedure.
1 Remove the four (M2.5x2.5) screws that secure the display hinges to the display back-cover.
2 Remove the two (M2x2) screws that secure the display hinges to the display back-cover.
3 Lift the display hinges o the display back-cover.
Installing the display hinges
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
Removing and installing components 57
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of display hinges and provides a visual representation of the installation procedure.
1 Align the screw holes on the hinges with the screw holes on the display back-cover.
2 Replace the two (M2x2) screws that secure the display hinges to the display back-cover.
3 Replace the four (M2.5x2.5) screws to secure the display hinges to the display back-cover.
1 Install the display bezel.
2 Install the display assembly.
3 Install the WLAN card.
4 Install the battery.
5 Install the base cover.
6 Follow the procedure in After working inside your computer.
Camera
Removing the camera
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the display assembly.
6 Remove the display bezel.
7 Remove the display panel.
58 Removing and installing components
The following image indicates the location of camera and provides a visual representation of the removal procedure.
1 Peel the tape that secures the camera to the display back-cover
2 Using a plastic scribe, pry the camera from the alignment post on the display back-cover.
3 Turn over the camera and disconnect the camera cable o the camera.
4 Peel the tape o the camera and lift the camera o the display back-cover.
Installing the camera
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of camera and provides a visual representation of the installation procedure.
Removing and installing components 59
1 Adhere the camera to the display cable (tape) and connect the camera cable to the camera and turn it over.
2 Using the alignment post, turn the camera over and adhere to the display back-cover.
3 Adhere the tape that secures the camera to the display back-cover.
1 Install the display panel.
2 Install the display bezel.
3 Install the display assembly.
4 Install the WLAN card.
5 Install the battery.
6 Install the base cover.
7 Follow the procedure in After working inside your computer.
Display back-cover
Removing the display back-cover
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
5 Remove the display assembly.
6 Remove the display bezel.
7 Remove the display hinges.
8 Remove thedisplay panel.
9 Remove the display cable.
10 Remove the camera.
60 Removing and installing components
The following image indicates the display back-cover and provides a visual representation of the removal procedure.
After performing all the prerequisites, we are left with the display back-cover.
NOTE: Antenna cables are a part of the palm-rest and keyboard assembly for computers shipping with WLAN
congurations.
Installing the display back-cover
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the display back-cover and provides a visual representation of the installation procedure.
Place the display back-cover on a at surface.
NOTE: Antenna cables are a part of the palm-rest and keyboard assembly for computers shipping with WLAN
congurations.
1 Install the camera.
2 Install the display cable.
Removing and installing components 61
3 Install the display panel.
4 Install the display hinges.
5 Install the display bezel.
6 Install the display assembly.
7 Install the WLAN card.
8 Install the battery.
9 Install the base cover.
10 Follow the procedure in After working inside your computer.
Display cable
Removing the display cable
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the display assembly.
5 Remove the display panel.
6 Remove the display bezel.
The following image indicates the location of display cable and provides a visual representation of the removal procedure.
1 Peel o the tape securing the display cable to the back-cover.
2 Peel the display cable o the display back-cover.
62 Removing and installing components
Installing the display cable
NOTE: This procedure is not applicable to computers shipped with a WWAN conguration.
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the location of display cable and provides a visual representation of the installation procedure.
1 Adhere the tape securing the display cable to the back-cover.
2 Adhere the display cable to the display back-cover.
1 Install the display bezel.
2 Install the display panel.
3 Install the display assembly.
4 Install the battery.
5 Install the base cover.
6 Follow the procedure in After working inside your computer.
Palm-rest and keyboard assembly
Removing the palm-rest and keyboard assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the battery.
4 Remove the WLAN card.
Removing and installing components 63
5 Remove the speakers.
6 Remove the system board.
7 Remove the display assembly.
8 Remove the power button with ngerprint reader or power-button board, whichever applicable.
9 Remove the power-adapter port.
10 Remove the touchpad.
The following image indicates the palm-rest and keyboard assembly and provides a visual representation of the removal procedure.
After performing the steps in the pre-requisites, we are left with the palm-rest and keyboard assembly.
NOTE: Antenna cables are a part of the display back-cover for computers shipping with WWAN conguration.
NOTE: System board can be removed with heatsink attached.
Installing the palm-rest and keyboard assembly
If you are replacing a component, remove the existing component before performing the installation procedure.
The following image indicates the palm-rest and keyboard assembly and provides a visual representation of the installation procedure.
64 Removing and installing components
Place the palm-rest and keyboard assembly on a at surface.
NOTE: Antenna cables are a part of the display back-cover for computers shipping with WWAN conguration.
1 Install the touchpad.
2 Install the power-adapter port.
3 Install the power button with ngerprint reader or power-button board, whichever applicable.
4 Install the display assembly.
5 Install the system board.
6 Install the speakers.
7 Install the WLAN card.
8 Install the battery.
9 Install the base cover.
10 Follow the procedure in After working inside your computer.
Removing and installing components 65
Troubleshooting
Enhanced Pre-Boot System Assessment (ePSA)
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal
when the diagnostic tests are performed.
For more information, see Dell EPSA Diagnostic 3.0.
Running the ePSA diagnostics
1 Turn on your computer.
2 As the computer boots, press the F12 key as the Dell logo appears.
3 On the boot menu screen, select the Diagnostics option.
4 Click the arrow at the bottom left corner.
Diagnostics front page is displayed.
5 Click the arrow in the lower-right corner to go to the page listing.
The items detected are listed.
6 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.
7 Select the device from the left pane and click Run Tests.
8 If there are any issues, error codes are displayed.
Note the error code and validation number and contact Dell.
System diagnostic lights
Battery-status light
Indicates the power and battery-charge status.
Solid white — Power adapter is connected and the battery has more than 5 percent charge.
Amber — Computer is running on battery and the battery has less than 5 percent charge.
O
4
66 Troubleshooting
• Power adapter is connected and the battery is fully charged.
• Computer is running on battery and the battery has more than 5 percent charge.
• Computer is in sleep state, hibernation, or turned o.
The power and battery-status light blinks amber along with beep codes indicating failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by
a pause. This 2,3 pattern continues until the computer is turned o indicating no memory or RAM is detected.
The following table shows dierent power and battery-status light patterns and associated problems.
Table 4. LED codes
Diagnostic light codes Problem description
2,1 Processor failure
2,2 System board: BIOS or ROM (Read-Only Memory) failure
2,3 No memory or RAM (Random-Access Memory) detected
2,4 Memory or RAM (Random-Access Memory) failure
2,5 Invalid memory installed
2,6 System-board or chipset error
2,7 Display failure
3,1 Coin-cell battery failure
3,2 PCI, video card/chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
3,5 Power-rail failure
3,6 System BIOS Flash incomplete
3,7 Management Engine (ME) error
Camera status light: Indicates whether the camera is in use.
• Solid white — Camera is in use.
•O — Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
• Solid white — Caps Lock enabled.
•O — Caps Lock disabled.
Flashing BIOS (USB key)
1 Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program le.
2 Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.
3 Copy the BIOS setup program le to the bootable USB drive.
4 Connect the bootable USB drive to the computer that needs the BIOS update.
5 Restart the computer and press F12 when the Dell logo is displayed on the screen.
6 Boot to the USB drive from the One Time Boot Menu.
7 Type the BIOS setup program lename and press Enter.
8 The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.
Troubleshooting 67
Flashing the BIOS
You may need to ash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to ash the BIOS:
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
4 Click Drivers & downloads > Find it myself.
5 Select the operating system installed on your computer.
6 Scroll down the page and expand BIOS.
7 Click Download to download the latest version of the BIOS for your computer.
8 After the download is complete, navigate to the folder where you saved the BIOS update le.
9 Double-click the BIOS update le icon and follow the instructions on the screen.
Backup media and recovery options
Dell proposes multiple options for recovering Windows operating system on your Dell PC. For more information. see Dell Windows Backup
Media and Recovery Options.
WiFi power cycle
If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be performed. The
following procedure provides the instructions on how to conduct a WiFi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
1 Turn o your computer.
2 Turn o the modem.
3 Turn o the wireless router.
4 Wait for 30 seconds.
5 Turn on the wireless router.
6 Turn on the modem.
7 Turn on your computer.
Flea power release
Flea power is the residual static electricity that remains on the computer even after it has been powered o and the battery has been
removed. The following procedure provides the instructions on how to conduct ea power release:
1 Turn o your computer.
2 Disconnect the power adapter from your computer.
3 Press and hold the power button for 15 seconds to drain the ea power.
4 Connect the power adapter to your computer.
5 Turn on your computer.
68 Troubleshooting
Getting help
Contacting Dell
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
5
Getting help 69