Table of Contents
- Dell Precision 5530 2-in-1 Service Manual
- Working on your computer
- Technology and components
- Removing and installing components
- Troubleshooting
- Getting help
DELL 5530 User Manual
Displayed below is the user manual for 5530 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Precision 5530 2-in-1
Service Manual
Regulatory Model: P73F
Regulatory Type: P73F001
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2018 Dell Inc. or its subsidiaries. All rights reserved. Dell, EMC, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks
may be trademarks of their respective owners.
2018 - 10
Rev. A01
Contents
1 Working on your computer............................................................................................................................. 5
Safety instructions.............................................................................................................................................................5
Turning o your computer — Windows 10.....................................................................................................................5
Before working inside your computer..............................................................................................................................5
After working inside your computer.................................................................................................................................6
2 Technology and components..........................................................................................................................7
HDMI 1.4.............................................................................................................................................................................. 7
HDMI 1.4 Features........................................................................................................................................................ 7
Advantages of HDMI....................................................................................................................................................7
USB features.......................................................................................................................................................................8
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB).............................................................................................................8
Speed.............................................................................................................................................................................8
Applications...................................................................................................................................................................9
Compatibility................................................................................................................................................................. 9
USB Type-C.......................................................................................................................................................................10
Alternate Mode........................................................................................................................................................... 10
USB Power Delivery................................................................................................................................................... 10
USB Type-C and USB 3.1........................................................................................................................................... 10
Thunderbolt over Type-C.......................................................................................................................................... 10
Thunderbolt 3 over Type-C........................................................................................................................................ 11
Key Features of Thunderbolt 3 over USB Type-C ..................................................................................................11
Thunderbolt Icons........................................................................................................................................................11
3 Removing and installing components............................................................................................................12
Recommended tools.........................................................................................................................................................12
Screw list........................................................................................................................................................................... 12
Base cover.........................................................................................................................................................................13
Removing the base cover..........................................................................................................................................13
Installing the base cover............................................................................................................................................ 16
Solid-state drive............................................................................................................................................................... 20
Removing the solid-state drive................................................................................................................................ 20
Installing the solid-state drive....................................................................................................................................21
I/O-board interposers......................................................................................................................................................22
Removing the IO board interposer...........................................................................................................................22
Installing the IO board interposer ............................................................................................................................ 23
Heat sink........................................................................................................................................................................... 25
Removing the heat sink.............................................................................................................................................25
Installing the heat sink............................................................................................................................................... 27
System fans...................................................................................................................................................................... 28
Removing the system fans....................................................................................................................................... 28
Installing the system fans..........................................................................................................................................29
Battery...............................................................................................................................................................................30
Contents 3
Lithium-ion battery precautions............................................................................................................................... 30
Removing the battery.................................................................................................................................................31
Installing the battery...................................................................................................................................................31
IO board.............................................................................................................................................................................32
Removing the IO board............................................................................................................................................. 32
Installing the IO board................................................................................................................................................34
Speakers............................................................................................................................................................................36
Removing the speakers.............................................................................................................................................36
Installing the speakers................................................................................................................................................37
Coin-cell battery...............................................................................................................................................................38
Removing the coin cell battery.................................................................................................................................38
Installing the coin cell battery...................................................................................................................................39
Power button with ngerprint reader............................................................................................................................39
Removing the power button with ngerprint reader.............................................................................................40
Installing the power button with ngerprint reader................................................................................................41
Display assembly............................................................................................................................................................... 41
Removing the display assembly................................................................................................................................42
Installing the display assembly..................................................................................................................................43
System board................................................................................................................................................................... 45
Removing the system board.....................................................................................................................................45
Installing the system board....................................................................................................................................... 47
Palm-rest and keyboard assembly................................................................................................................................. 49
Removing the palmrest and keyboard assembly....................................................................................................49
Installing the palm-rest and keyboard assembly.................................................................................................... 50
4 Troubleshooting........................................................................................................................................... 52
Enhanced Pre-Boot System Assessment — ePSA diagnostics................................................................................52
Running the ePSA Diagnostics.................................................................................................................................52
System diagnostic lights................................................................................................................................................. 52
Diagnostic error messages..............................................................................................................................................53
System error messages...................................................................................................................................................56
Real Time Clock reset......................................................................................................................................................57
Flashing the BIOS.............................................................................................................................................................57
Flashing the BIOS from the F12 One-Time boot menu............................................................................................... 58
Flashing BIOS (USB key)................................................................................................................................................ 60
Wi-Fi power cycle............................................................................................................................................................. 61
Flea power release............................................................................................................................................................61
5 Getting help.................................................................................................................................................62
Contacting Dell.................................................................................................................................................................62
4Contents
Working on your computer
Safety instructions
Use the following safety guidelines to protect your computer from potential damage and to ensure your personal safety. Unless otherwise
noted, each procedure included in this document assumes that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or, if purchased separately, installed by performing the removal procedure in reverse order.
WARNING: Disconnect all power sources before opening the computer cover or panels. After you nish working inside the
computer, replace all covers, panels, and screws before connecting to the power source.
WARNING: Before working inside your computer, read the safety information that shipped with your computer. For additional
safety best practices information, see the Regulatory Compliance Homepage
CAUTION: Many repairs may only be done by a certied service technician. You should only perform troubleshooting and simple
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team.
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its
edges or by its metal mounting bracket. Hold a component such as a processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable itself. Some cables have
connectors with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the
cable. As you pull connectors apart, keep them evenly aligned to avoid bending any connector pins. Also, before you connect a
cable, ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear dierently than shown in this document.
Turning o your computer — Windows 10
CAUTION: To avoid losing data, save and close all open les and exit all open programs before you turn o your computer or
remove the side cover.
1 Click or tap .
2 Click or tap and then click or tap Shut down.
NOTE: Ensure that the computer and all attached devices are turned o. If your computer and attached devices did not
automatically turn o when you shut down your operating system, press and hold the power button for about 6 seconds to
turn them o.
Before working inside your computer
To avoid damaging your computer, perform the following steps before you begin working inside the computer.
1 Ensure that you follow the Safety Instruction.
2 Ensure that your work surface is at and clean to prevent the computer cover from being scratched.
1
Working on your computer 5
3 Turn o your computer.
4 Disconnect all network cables from the computer.
CAUTION: To disconnect a network cable, rst unplug the cable from your computer and then unplug the cable from the
network device.
5 Disconnect your computer and all attached devices from their electrical outlets.
6 Press and hold the power button while the computer is unplugged to ground the system board.
NOTE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an
unpainted metal surface at the same time as touching a connector on the back of the computer.
After working inside your computer
After you complete any replacement procedure, ensure that you connect any external devices, cards, and cables before turning on your
computer.
1 Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, rst plug the cable into the network device and then plug it into the
computer.
2 Connect your computer and all attached devices to their electrical outlets.
3 Turn on your computer.
4 If required, verify that the computer works correctly by running ePSA diagnostics.
6Working on your computer
Technology and components
NOTE: Instructions provided in this section are applicable on computers shipped with Windows 10 operating system. Windows 10
is factory-installed with this computer.
Topics:
• HDMI 1.4
• USB features
• USB Type-C
HDMI 1.4
This topic explains the HDMI 1.4 and its features along with the advantages.
HDMI (High-Denition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable
reduction and content protection provisions. HDMI supports standard, enhanced, or high-denition video, plus multichannel digital audio on
a single cable.
NOTE: The HDMI 1.4 will provide 5.1 channel audio support.
HDMI 1.4 Features
•HDMI Ethernet Channel - Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled
devices without a separate Ethernet cable
•Audio Return Channel - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio system,
eliminating the need for a separate audio cable
•3D - Denes input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications
•Content Type - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings
based on content type
•Additional Color Spaces - Adds support for additional color models used in digital photography and computer graphics
•4K Support - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema systems
used in many commercial movie theaters
•HDMI Micro Connector - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p
•Automotive Connection System - New cables and connectors for automotive video systems, designed to meet the unique demands of
the motoring environment while delivering true HD quality
Advantages of HDMI
• Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.
• Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a
simple, cost-eective manner
• Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound
• HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables
currently used in A/V systems
2
Technology and components 7
• HDMI supports communication between the video source (such as a DVD player) and the DTV, enabling new functionality
USB features
Universal Serial Bus, or USB, was introduced in 1996. It dramatically simplied the connection between host computers and peripheral
devices like mice, keyboards, external drivers, and printers.
Let's take a quick look on the USB evolution referencing to the table below.
Table 1. USB evolution
Type Data Transfer Rate Category Introduction Year
USB 2.0 480 Mbps High Speed 2000
USB 3.0/USB 3.1 Gen 1 5 Gbps Super Speed 2010
USB 3.1 Gen 2 10 Gbps Super Speed 2013
USB 3.0/USB 3.1 Gen 1 (SuperSpeed USB)
For years, the USB 2.0 has been rmly entrenched as the de facto interface standard in the PC world with about 6 billion devices sold, and
yet the need for more speed grows by ever faster computing hardware and ever greater bandwidth demands. The USB 3.0/USB 3.1 Gen 1
nally has the answer to the consumers' demands with a theoretically 10 times faster than its predecessor. In a nutshell, USB 3.1 Gen 1
features are as follows:
• Higher transfer rates (up to 5 Gbps)
• Increased maximum bus power and increased device current draw to better accommodate power-hungry devices
• New power management features
• Full-duplex data transfers and support for new transfer types
• Backward USB 2.0 compatibility
• New connectors and cable
The topics below cover some of the most commonly asked questions regarding USB 3.0/USB 3.1 Gen 1.
Speed
Currently, there are 3 speed modes dened by the latest USB 3.0/USB 3.1 Gen 1 specication. They are Super-Speed, Hi-Speed and Full-
Speed. The new SuperSpeed mode has a transfer rate of 4.8Gbps. While the specication retains Hi-Speed, and Full-Speed USB mode,
commonly known as USB 2.0 and 1.1 respectively, the slower modes still operate at 480Mbps and 12Mbps respectively and are kept to
maintain backward compatibility.
USB 3.0/USB 3.1 Gen 1 achieves the much higher performance by the technical changes below:
• An additional physical bus that is added in parallel with the existing USB 2.0 bus (refer to the picture below).
• USB 2.0 previously had four wires (power, ground, and a pair for dierential data); USB 3.0/USB 3.1 Gen 1 adds four more for two pairs
of dierential signals (receive and transmit) for a combined total of eight connections in the connectors and cabling.
• USB 3.0/USB 3.1 Gen 1 utilizes the bidirectional data interface, rather than USB 2.0's half-duplex arrangement. This gives a 10-fold
increase in theoretical bandwidth.
8Technology and components
With today's ever increasing demands placed on data transfers with high-denition video content, terabyte storage devices, high megapixel
count digital cameras etc., USB 2.0 may not be fast enough. Furthermore, no USB 2.0 connection could ever come close to the 480Mbps
theoretical maximum throughput, making data transfer at around 320Mbps (40MB/s) — the actual real-world maximum. Similarly, USB
3.0/USB 3.1 Gen 1 connections will never achieve 4.8Gbps. We will likely see a real-world maximum rate of 400MB/s with overheads. At this
speed, USB 3.0/USB 3.1 Gen 1 is a 10x improvement over USB 2.0.
Applications
USB 3.0/USB 3.1 Gen 1 opens up the laneways and provides more headroom for devices to deliver a better overall experience. Where USB
video was barely tolerable previously (both from a maximum resolution, latency, and video compression perspective), it's easy to imagine
that with 5-10 times the bandwidth available, USB video solutions should work that much better. Single-link DVI requires almost 2Gbps
throughput. Where 480Mbps was limiting, 5Gbps is more than promising. With its promised 4.8Gbps speed, the standard will nd its way
into some products that previously weren't USB territory, like external RAID storage systems.
Listed below are some of the available SuperSpeed USB 3.0/USB 3.1 Gen 1 products:
• External Desktop USB 3.0/USB 3.1 Gen 1 Hard Drives
• Portable USB 3.0/USB 3.1 Gen 1 Hard Drives
• USB 3.0/USB 3.1 Gen 1 Drive Docks & Adapters
• USB 3.0/USB 3.1 Gen 1 Flash Drives & Readers
• USB 3.0/USB 3.1 Gen 1 Solid-state Drives
• USB 3.0/USB 3.1 Gen 1 RAIDs
• Optical Media Drives
• Multimedia Devices
• Networking
• USB 3.0/USB 3.1 Gen 1 Adapter Cards & Hubs
Compatibility
The good news is that USB 3.0/USB 3.1 Gen 1 has been carefully planned from the start to peacefully co-exist with USB 2.0. First of all,
while USB 3.0/USB 3.1 Gen 1 species new physical connections and thus new cables to take advantage of the higher speed capability of
the new protocol, the connector itself remains the same rectangular shape with the four USB 2.0 contacts in the exact same location as
before. Five new connections to carry receive and transmitted data independently are present on USB 3.0/USB 3.1 Gen 1 cables and only
come into contact when connected to a proper SuperSpeed USB connection.
Technology and components 9
Windows 10 will be bringing native support for USB 3.1 Gen 1 controllers. This is in contrast to previous versions of Windows, which
continue to require separate drivers for USB 3.0/USB 3.1 Gen 1 controllers.
USB Type-C
USB Type-C is a new, tiny physical connector. The connector itself can support various exciting new USB standards like USB 3.1 and USB
power delivery (USB PD).
Alternate Mode
USB Type-C is a new connector standard that is very small. It is about a third the size of an old USB Type-A plug. This is a single connector
standard that every device should be able to use. USB Type-C ports can support a variety of dierent protocols using “alternate modes,”
which allows you to have adapters that can output HDMI, VGA, DisplayPort, or other types of connections from that single USB port
USB Power Delivery
The USB PD specication is also closely intertwined with USB Type-C. Currently, smartphones, tablets, and other mobile devices often use
a USB connection to charge. A USB 2.0 connection provides up to 2.5 watts of power — that'll charge your phone, but that's about it. A
laptop might require up to 60 watts, for example. The USB Power Delivery specication ups this power delivery to 100 watts. It's bi-
directional, so a device can either send or receive power. And this power can be transferred at the same time the device is transmitting
data across the connection.
This could spell the end of all those proprietary laptop charging cables, with everything charging via a standard USB connection. You could
charge your laptop from one of those portable battery packs you charge your smartphones and other portable devices from today. You
could plug your laptop into an external display connected to a power cable, and that external display would charge your laptop as you used
it as an external display — all via the one little USB Type-C connection. To use this, the device and the cable have to support USB Power
Delivery. Just having a USB Type-C connection doesn't necessarily mean they do.
USB Type-C and USB 3.1
USB 3.1 is a new USB standard. USB 3's theoretical bandwidth is 5 Gbps, while USB 3.1's is 10 Gbps. That's double the bandwidth, as fast
as a rst-generation Thunderbolt connector. USB Type-C isn't the same thing as USB 3.1. USB Type-C is just a connector shape, and the
underlying technology could just be USB 2 or USB 3.0. In fact, Nokia's N1 Android tablet uses a USB Type-C connector, but underneath it's
all USB 2.0 — not even USB 3.0. However, these technologies are closely related.
Thunderbolt over Type-C
Thunderbolt is a hardware interface that combines data, video, audio, and power in a single connection. Thunderbolt combines PCI Express
(PCIe) and DisplayPort (DP) into one serial signal, and additionally provides DC power, all in one cable. Thunderbolt 1 and Thunderbolt 2 use
the same connector as miniDP (DisplayPort) to connect to peripherals, while Thunderbolt 3 uses a USB Type-C connector.
10 Technology and components
Figure 1. Thunderbolt 1 and Thunderbolt 3
1 Thunderbolt 1 and Thunderbolt 2 (using a miniDP connector)
2 Thunderbolt 3 (using a USB Type-C connector)
Thunderbolt 3 over Type-C
Thunderbolt 3 brings Thunderbolt to USB Type-C at speeds up to 40 Gbps, creating one compact port that does it all - delivering the
fastest, most versatile connection to any dock, display or data device like an external hard drive. Thunderbolt 3 uses a USB Type-C
connector/port to connect to supported peripherals.
1 Thunderbolt 3 uses USB Type-C connector and cables - It is compact and reversible
2 Thunderbolt 3 supports speed up to 40 Gbps
3 DisplayPort 1.2 – compatible with existing DisplayPort monitors, devices and cables
4 USB Power Delivery - Up to 130W on supported computers
Key Features of Thunderbolt 3 over USB Type-C
1 Thunderbolt, USB, DisplayPort and power on USB Type-C on a single cable (features vary between dierent products)
2 USB Type-C connector and cables which are compact and reversible
3 Supports Thunderbolt Networking (*varies between dierent products)
4 Supports up to 4K displays
5 Up to 40 Gbps
NOTE: Data transfer speed may vary between dierent devices.
Thunderbolt Icons
Figure 2. Thunderbolt Iconography Variations
Technology and components 11
Removing and installing components
Recommended tools
The procedures in this document may require the following tools:
• Phillips #00 and #01 screwdriver
• Torx #5 (T5) screwdriver
• Plastic scribe
Screw list
The following table provides the list of screws that are used for securing dierent components.
Table 2. Screw list
Component Secured to Screw type Quantity Screw image
Base cover Palm-rest and keyboard
assembly
Torx head M2x3 8
Battery Palm-rest and keyboard
assembly
M2x5 8
Display assembly Palm-rest and keyboard
assembly
M2.5x4 6
Display-cable bracket System board M1.6x1.8 2
Fans Palm-rest and keyboard
assembly
M2x3 4
Fingerprint-reader Palm-rest and keyboard
assembly
M1.6x1.8 1
Heat sink System board M2x3 5
I/O board Palm-rest and keyboard
assembly
M2x3 1
I/O-board interposer Palm-rest and keyboard
assembly
M1.6x5.5 4
Power button Palm-rest and keyboard
assembly
M2x1.7 1
Speakers Palm-rest and keyboard
assembly
M2x1.7 2
3
12 Removing and installing components
Component Secured to Screw type Quantity Screw image
Solid-state drive System board M2x3 1
System board Palm-rest and keyboard
assembly
M2x3 2
USB Type-C bracket I/O board M2x4 3
Type-C USB bracket System board M2x4 3
Wireless-antenna
bracket
System board M2x4 2
Base cover
Removing the base cover
1 Follow the procedure in Before working inside your computer
2 To remove the base cover:
a Remove the eight torx head screws (M2x3) that secure the base cover to the palm-rest and keyboard assembly.
Removing and installing components 13
b Using a plastic scribe, pry the base cover from the right corner of the palm-rest and keyboard assembly.
NOTE: Do not begin to pry the base cover from top edge (next to hinges), as this may break the plastic clips and lead
to cosmetic damage.
c Pry the base cover starting from the right side of palm-rest and keyboard assembly.
d Pry the base cover from the bottom left corner of the palm-rest and keyboard assembly.
e Pry the base cover from the left side of the palm-rest and keyboard assembly.
f Move the base cover from left to right and lift the base cover from the palm-rest and keyboard assembly.
14 Removing and installing components
gTurn-o the battery switch.
Removing and installing components 15
NOTE: Turn-o the battery switch before you proceed to remove any other component from your computer.
Installing the base cover
1 Turn-on the battery switch, it was turned o earlier.
16 Removing and installing components
2 Align the screw holes on the base cover with the screw holes on the palm-rest and keyboard assembly.
Removing and installing components 17
[
3 Snap the base cover into the tabs on the palm-rest and keyboard assembly [1, 2].
18 Removing and installing components
4 Replace the eight torx head screws (M2x3) that secure the base cover to the palm-rest and keyboard assembly.
Removing and installing components 19
5 Follow the procedure in After working inside your computer
Solid-state drive
Removing the solid-state drive
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 To remove the solid-state drive (SSD):
a Peel and remove the thermal pad from the solid-state drive.
20 Removing and installing components
b Remove the screw (M2x3) that secures the solid-state drive to the system board [1].
c Lift the solid-state drive at an angle, then slide and remove the solid-state drive from the solid-state drive slot [2].
Installing the solid-state drive
1 Align the notch on the solid-state drive with the tab on the solid-state drive slot [1].
2 At an angle, slide the solid-state drive into the solid-state drive slot [2].
3 Replace the screw (M2x3) that secures the solid-state drive to the system board [3].
Removing and installing components 21
4 Ax the thermal pad on the solid-state drive.
5 Install the base cover.
6 Follow the procedure in After working inside your computer.
I/O-board interposers
Removing the IO board interposer
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 To remove the IO board interposer:
22 Removing and installing components
a Remove the four screws (M1.6x5.5) that secure the I/O-board cable to the system board [1].
b Peel and remove the I/O-board cable from the fans [2].
c Remove the two I/O-board interposers from the system board [3].
NOTE: Remove the I/O-board interposers immediately after removing the I/O-board cable to prevent the interposers
from falling out of your computer. The pins on the interposer boards are very fragile. Avoid contact with the pins or
bottom of the boards, instead handle the boards by lifting and holding from the edges or side. After removing the
interposer boards from the system, place them on an ESD mat in a location where contact and movement can be
avoided. DO NOT push or apply pressure to the pins on the interposer boards and DO NOT use any motion that may
scratch the pins, such as rotating/turning the boards while they are in contact with any surface.
Installing the IO board interposer
1 Using the alignment posts, place the two I/O-board interposers on the system board.
Removing and installing components 23
2 Align the screw holes on the I/O-board cable with the screw holes on the I/O-board interposers and adhere the I/O-board cable to
the fans [1].
NOTE: When installing the I/O board cable, align and connect the I/O board end to the I/O board side and the system board
end to the system board side.
CAUTION: Wrong alignment of the cable might cause damage to the connectors.
3 Replace the four screws (M1.6x5.5) that secure the I/O-board cable to the system board [2].
24 Removing and installing components
4 Install the base cover.
5 Follow the procedure in After working inside your computer.
Heat sink
Removing the heat sink
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 To remove the heat sink:
a Peel the tape that secures the heat-sink shield to the system board [1].
NOTE: The tape on the heat-sink shield is necessary to reduce the noise for the system. The tape can be reused and
has to be adhered when the heat-sink shield is installed.
b Using a plastic scribe, release the heat-sink shield from the slots on the system board [2].
c Lift the heat-sink shield o the system board [3].
Removing and installing components 25
d In reverse sequential order (as indicated on the heat sink), remove the four screws (M2x3) that secure the heat sink to the
system board [4].
e Remove the screw (M2x3) that secures the heat sink to the palm-rest and keyboard assembly [5].
f Lift the heat sink o the system board [6].
26 Removing and installing components
Installing the heat sink
1 Place the heat sink on the system board and align the screw holes on the heat sink with the screw holes on the system board [1].
2 In sequential order (as indicated on the heat sink), replace the ve screws (M2x3) that secure the heat sink to the system board [2].
3 Replace the screw (M2x3) that secures the heat sink to the palm-rest and keyboard assembly [3].
4 Place the heat-sink shield on the slots on the system board [1] and press down the heat-sink shield to snap it into place [2].
5 Ax the tape that secures the heat-sink shield to the system board [3].
Removing and installing components 27
6 Install the base cover.
7 Follow the procedure in After working inside your computer.
System fans
Removing the system fans
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 To remove the system fans:
a Remove the coin-cell battery cable from the routing guides on the system fans [1].
b Disconnect the system fan cable from the system board [2].
c Remove the four screws (M2x3) that secure the system fans to the palm-rest and keyboard assembly [3].
d Lift the system fans along with their cable, o the system board [4].
28 Removing and installing components
Installing the system fans
1 Align the screw holes on the system fans with the screw holes on the palm-rest and keyboard assembly [1].
2 Replace the four screws (M2x3) that secure the system fans to the palm-rest and keyboard assembly [2].
3 Connect the system fan cable to the system board [3].
4 Route the coin-cell battery cable through the routing guides on the system fans [4].
Removing and installing components 29
5 Install the I/O-board interposers.
6 Install the base cover.
7 Follow the procedure in After working inside your computer.
Battery
Lithium-ion battery precautions
CAUTION:
• Exercise caution when handling Lithium-ion batteries.
• Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting the AC adapter
from the system to allow the battery to drain.
• Do not crush, drop, mutilate, or penetrate the battery with foreign objects.
• Do not expose the battery to high temperatures, or disassemble battery packs and cells.
• Do not apply pressure to the surface of the battery.
• Do not bend the battery.
• Do not use tools of any kind to pry on or against the battery.
• If a battery gets stuck in a device as a result of swelling, do not try to free it as puncturing, bending, or crushing a Lithium-ion
battery can be dangerous. In such an instance, the entire system should be replaced. Contact https://www.dell.com/support for
assistance and further instructions.
• Always purchase genuine batteries from https://www.dell.com or authorized Dell partners and re-sellers.
30 Removing and installing components
Removing the battery
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 To remove the battery:
a Using a plastic scribe, push the tab and disconnect the battery cable from the system board [1].
b Remove the eight screws (M2x5) that secure the battery to the palm-rest and keyboard assembly [2].
c Lift the battery o the palm-rest and keyboard assembly [3].
5 Turn the computer over, open the display, and press the power button for about 5 seconds to ground the computer.
Installing the battery
1 Place the battery on the palm-rest and keyboard assembly and align the screw holes on the battery with the screw holes on the palm-
rest and keyboard assembly [1].
2 Replace the eight screws (M2x5) that secure the battery to the palm-rest and keyboard assembly [2].
3 Connect the battery cable to the system board [3].
Removing and installing components 31
4 Install the I/O-board interposers.
5 install the base cover.
6 Follow the procedure in After working inside your computer.
IO board
Removing the IO board
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 Remove the battery.
5 To remove the I/O board:
a Remove the two screws (M2x4) that secure the wireless-antenna bracket to the I/O board [1].
b Using a plastic scribe, disconnect the antenna cables from the I/O board [2].
c Remove the three screws (M2x4) that secure the Type-C USB bracket to the I/O board [3].
d Using a plastic scribe, disconnect the speaker cable from the I/O board [4].
e Disconnect the LED and microphone cable from the I/O board [5].
32 Removing and installing components
f Remove the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly [1].
g Lift the I/O board o the palm-rest and keyboard assembly [2].
Removing and installing components 33
Installing the IO board
1 Using the alignment posts, align the screw hole on the I/O board with the screw hole on the palm-rest and keyboard assembly [1].
2 Replace the screw (M2x3) that secures the I/O board to the palm-rest and keyboard assembly [2].
34 Removing and installing components
3 Connect the antenna cables to the I/O board [1].
4 Place the wireless-antenna bracket on the I/O board and replace the two screws (M2x4) that secure the wireless-antenna bracket to
the I/O board [2].
5 Place the Type-C USB bracket on the I/O board and replace the three screws (M2x4) that secure the Type-C USB bracket to the I/O
board [3].
6 Connect the speaker cable to the I/O board [4].
7 Connect the LED and microphone cable to the I/O board [5].
Removing and installing components 35
8 Install the battery.
9 Install the I/O-board interposers.
10 install the base cover.
11 Follow the procedure in After working inside your computer.
Speakers
Removing the speakers
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 Remove the battery.
5 To remove the speakers:
a Disconnect the speaker cable from the I/O board [1].
b Remove the two screws (M2x1.7) that secure the left and right speakers to the palm-rest and keyboard assembly [2].
c Unroute the speaker-cable and remove the cable from the routing guides on the palm-rest and keyboard assembly [3].
36 Removing and installing components
d Lift the left and right speakers, along with their cables, o the palm-rest and keyboard assembly [4].
Installing the speakers
1 Using the alignment posts, place the left and right speaker on the palm-rest and keyboard assembly [1].
2 Using the routing guides, route the speaker cable on the palm-rest and keyboard assembly [2].
3 Replace the two screws (M2x1.7) that secure the left and right speakers to the palm-rest and keyboard assembly [3].
4 Connect the speaker cable to the I/O board [4].
Removing and installing components 37
5 Install the battery.
6 Install the I/O-board interposers.
7 install the base cover.
8 Follow the procedure in After working inside your computer.
Coin-cell battery
Removing the coin cell battery
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 Remove the battery.
5 To remove the coin cell battery:
a Disconnect the coin-cell battery cable from the system board and release the coin-cell battery cable from the routing guides on
the fan [1].
b Note the location of the coin-cell battery and pry it o the system board [2].
38 Removing and installing components
Installing the coin cell battery
1 Ax the coin-cell battery to the system board [1].
2 Using the routing guides, route the coin-cell battery cable on the system fans [2].
3 Connect the coin-cell battery cable to the system board [3].
4 Install the battery.
5 Install the I/O-board interposers.
6 install the base cover.
7 Follow the procedure in After working inside your computer.
Power button with ngerprint reader
Removing and installing components 39
Removing the power button with ngerprint reader
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 Remove the battery.
5 Remove the I/O board.
6 To remove the power button with ngerprint (optional):
NOTE: Step 1, 2, and 4 are applicable only for the computers that are shipped with ngerprint
reader.
a Open the latch and disconnect the ngerprint-reader cable from the system board and peel the ngerprint-reader cable from
the palm-rest and keyboard assembly [1].
b Unroute the ngerprint reader cable [2].
c Peel the tape that secures the power button cable to the palm-rest and keyboard assembly [3].
d Remove the screw (M1.6x1.8) that secures the ngerprint-reader to the palm-rest and keyboard assembly [4].
e Remove the screw (M2x1.7) that secures the power button to the palm-rest and keyboard assembly [5].
f Peel and lift the power button and ngerprint reader (optional), along with its cable, o the palm-rest and keyboard assembly
[6].
40 Removing and installing components
Installing the power button with ngerprint reader
NOTE: Step 3, 4, and 5 are applicable only for the computers that are shipped with ngerprint reader.
1 Place the power button and ngerprint reader (optional) into its slot on the palm-rest and keyboard assembly [1].
2 Replace the screw (M2x1.7) that secures the power button to the palm-rest and keyboard assembly [2].
3 Replace the screw (M1.6x1.8) that secures the ngerprint-reader to the palm-rest and keyboard assembly [3].
4 Ax the tape that secures the power button cable to the palm-rest and keyboard assembly [4].
5 Route the ngerprint-reader cable to the palm-rest and keyboard assembly [5].
6 Connect the ngerprint-reader cable to the system board and close the latch [6].
7 Install the I/O board.
8 Install the battery.
9 Install the I/O-board interposers.
10 install the base cover.
11 Follow the procedure in After working inside your computer.
Display assembly
Removing and installing components 41
Removing the display assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the I/O-board interposers.
4 Remove the heat sink.
5 To remove the display assembly:
a Open the latch and disconnect the camera cable from the system board [1].
b Peel the camera cable from the palm-rest and keyboard assembly [2].
c Peel the tape that secures the display-cable bracket to the system board [3].
d Remove the two screws (M1.6x1.8) that secure the display-cable bracket to the system board and lift the bracket o the system
board [4].
e Using the pull tab, disconnect the display cable from the system board [5].
f Remove the two screws (M2x4) that secure the wireless-antenna bracket to the I/O board and lift the bracket o the I/O board
[6].
g Disconnect the antenna cables from the I/O board [7].
h Open the computer at a 180-degree angle and place it on a at and clean surface with the display screen facing down.
42 Removing and installing components
i Remove the six screws (M2.5x4) that secure the display assembly to the palm-rest and keyboard assembly [1].
j Lift the display assembly from the palm-rest assembly [2].
Installing the display assembly
1 With the display screen facing down, align the screw holes on the display assembly with the screw holes on the palm-rest and
keyboard assembly [1].
2 Replace the six screws (M2.5x4) that secure the display assembly to the palm-rest and keyboard assembly [2].
Removing and installing components 43
3 Close the display.
4 Connect the antenna cables to the I/O board [1].
5 Align the screw holes on the wireless-antenna bracket with the screw holes on the I/O board and replace the two screws (M2x4) that
secure the bracket to the I/O board [2].
6 Connect the display cable to the system board and close the latch [3].
7 Align the screw holes on the display-cable bracket with the screw holes on the system board and replace the two screws (M1.6x1.8)
that secure the bracket to the system board [4].
8 Ax the tape that secures the display-cable bracket to the system board [5].
9 Ax the camera cable to the palm-rest and keyboard assembly [6].
10 Connect the camera cable to the system board and close the latch [7].
44 Removing and installing components
11 Install the heat sink.
12 Install the I/O-board interposers.
13 install the base cover.
14 Follow the procedure in After working inside your computer.
System board
Removing the system board
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the solid state drive.
4 Remove the I/O-board interposers.
5 Remove the battery.
6 Remove the heat sink.
7 Remove the system fans.
Removing and installing components 45
8 To remove the system board:
a Open the latch and disconnect the camera cable from the system board [1].
b Peel the tape that secures the display-cable bracket to the system board [2].
c Remove the two screws (M1.6x1.8) that secure the display-cable bracket to the system board and lift the bracket o the system
board [3].
d Using the pull tab, disconnect the display cable from the system board [4].
e Open the latch and disconnect the keyboard-back light cable from the system board [5].
f Open the latch and disconnect the ngerprint-reader cable from the system board [6].
NOTE: Removing the coin-cell battery resets the BIOS setup program's settings to default. It is recommended that
you note the BIOS setup program's settings before removing the coin-cell battery.
g Disconnect the coin-cell battery cable from the system board [7].
h Remove the three screws (M2x4) that secure the Type-C USB bracket to system board and lift the bracket o the system
board [1].
i Remove the two screws (M2x3) that secure the system board to the palm-rest and keyboard assembly [2].
j Lift the system board o the palm-rest assembly [3].
46 Removing and installing components
Installing the system board
1 Using the alignment posts, place the system board on the palm-rest and keyboard assembly and align the screw holes on the system
board with the screw holes on the palm-rest assembly [1].
2 Replace the two screws (M2x3) that secure the system board to the palm-rest and keyboard assembly [2].
3 Align the screw holes on the Type-C USB bracket with the screw holes on the system board and replace the three screws (M2x4)
that secure the Type-C USB bracket to system board [3].
Removing and installing components 47
4 Connect the coin-cell battery cable to the system board [1].
5 Connect the ngerprint-reader cable to the system board and close the latch [2].
6 Connect the keyboard-back light cable to the system board and close the latch [3].
7 Connect the display cable to the system board [4].
8 Place the display-cable bracket on the system board and replace the two screws (M1.6x1.8) that secure the bracket to the system
board [5].
9 Ax the tape that secures the display-cable bracket to the system board [6].
10 Connect the camera cable to the system board and close the latch [7].
48 Removing and installing components
11 Install the system fans.
12 Install the heat sink.
13 Install the battery.
14 Install the I/O-board interposers.
15 Install the solid state drive.
16 install the base cover.
17 Follow the procedure in After working inside your computer.
Palm-rest and keyboard assembly
Removing the palmrest and keyboard assembly
1 Follow the procedure in Before working inside your computer.
2 Remove the base cover.
3 Remove the solid state drive.
4 Remove the I/O-board interposers.
Removing and installing components 49
5 Remove the battery.
6 Remove the heat sink.
7 Remove the system fans.
8 Remove the speakers.
9 Remove the coin cell battery.
10 Remove the display assembly.
11 Remove the I/O board.
12 Remove the power button with ngerprint reader.
13 Remove the system board.
14 The component you are left with is the palmrest and the keyboard assembly.
Installing the palm-rest and keyboard assembly
1 Place the palm-rest and keyboard assembly face down on a clean and at surface.
50 Removing and installing components
2 Install the system board.
3 Install the power button with ngerprint reader.
4 Install the I/O board.
5 Install the display assembly.
6 Install the coin cell battery.
7 install the speakers.
8 Install the system fans.
9 Install the heat sink.
10 Install the battery.
11 Install the I/O-board interposers.
12 Install the solid state drive.
13 install the base cover.
14 Follow the procedure in After working inside your computer.
Removing and installing components 51
Troubleshooting
Enhanced Pre-Boot System Assessment — ePSA
diagnostics
The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware. The ePSA is embedded with the
BIOS and is launched by the BIOS internally. The embedded system diagnostics provides a set of options for particular devices or device
groups allowing you to:
• Run tests automatically or in an interactive mode
• Repeat tests
• Display or save test results
• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)
• View status messages that inform you if tests are completed successfully
• View error messages that inform you of problems encountered during testing
NOTE: Some tests for specic devices require user interaction. Always ensure that you are present at the computer terminal
when the diagnostic tests are performed.
Running the ePSA Diagnostics
Invoke diagnostics boot by either of the methods that are suggested below:
1 Power on the computer.
2 As the computer boots, press the F12 key when the Dell logo is displayed.
3 In the boot menu screen, use Up/Down arrow key to select the Diagnostics option and then press Enter.
NOTE: The Enhanced Pre-boot System Assessment window displays, listing all devices detected in the computer. The
diagnostics starts running the tests on all the detected devices.
4 Press the arrow in the lower-right corner to go to the page listing.
The detected items are listed and tested.
5 To run a diagnostic test on a specic device, press Esc and click Yes to stop the diagnostic test.
6 Select the device from the left pane and click Run Tests.
7 If there are any issues, error codes are displayed.
Note the error code and contact Dell.
or
8 Shut down the computer.
9 Press and hold the Fn key, while pressing the power button, and then release both.
10 Repeat steps 3–7 above.
System diagnostic lights
Power and battery-status light
Indicates the power and battery-charge status.
Solid white—Power adapter is connected and the battery has more than 5 percent charge.
4
52 Troubleshooting
Solid amber—Computer is running on battery and the battery has less than 5 percent charge.
O
• Power adapter is connected and the battery is fully charged.
• Computer is running on battery and the battery has more than 5 percent charge.
• Computer is in sleep state, hibernation, or turned o.
The power and battery-status light blinks amber along with beep codes indicating failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by
a pause. This 2,3 pattern continues until the computer is turned o indicating no memory or RAM is detected.
The following table shows dierent power and battery-status light patterns and associated problems.
Table 3. Diagnostics
Light pattern Problem description
2,1 CPU failure
2,2 System board: BIOS and ROM failure
2,3 No memory or RAM detected
2,4 Memory or RAM failure
2,5 Invalid memory installed
2,6 System board or chipset error
2,7 LCD failure
3,1 CMOS battery failure
3,2 PCI or video card or chip failure
3,3 Recovery image not found
3,4 Recovery image found but invalid
Camera status light: Indicates whether the camera is in use.
• Solid white—Camera is in use.
•O—Camera is not in use.
Caps Lock status light: Indicates whether Caps Lock is enabled or disabled.
• Solid white—Caps Lock enabled.
•O—Caps Lock disabled.
Diagnostic error messages
Table 4. Diagnostic error messages
Error messages Description
AUXILIARY DEVICE FAILURE The touchpad or external mouse may be faulty. For an external
mouse, check the cable connection. Enable the Pointing Device
option in the System Setup program.
BAD COMMAND OR FILE NAME Ensure that you have spelled the command correctly, put spaces in
the proper place, and used the correct path name.
Troubleshooting 53
Error messages Description
CACHE DISABLED DUE TO FAILURE The primary cache internal to the microprocessor has failed.
Contact Dell
CD DRIVE CONTROLLER FAILURE The optical drive does not respond to commands from the
computer.
DATA ERROR The hard drive cannot read the data.
DECREASING AVAILABLE MEMORY One or more memory modules may be faulty or improperly seated.
Reinstall the memory modules or, if necessary, replace them.
DISK C: FAILED INITIALIZATION The hard drive failed initialization. Run the hard drive tests in Dell
Diagnostics.
DRIVE NOT READY The operation requires a hard drive in the bay before it can
continue. Install a hard drive in the hard drive bay.
ERROR READING PCMCIA CARD The computer cannot identify the ExpressCard. Reinsert the card
or try another card.
EXTENDED MEMORY SIZE HAS CHANGED The amount of memory recorded in non-volatile memory (NVRAM)
does not match the memory module installed in the computer.
Restart the computer. If the error appears again, Contact Dell
THE FILE BEING COPIED IS TOO LARGE FOR THE
DESTINATION DRIVE
The le that you are trying to copy is too large to t on the disk, or
the disk is full. Try copying the le to a dierent disk or use a larger
capacity disk.
A FILENAME CANNOT CONTAIN ANY OF THE FOLLOWING
CHARACTERS: \ / : * ? " < > | -
Do not use these characters in lenames.
GATE A20 FAILURE A memory module may be loose. Reinstall the memory module or, if
necessary, replace it.
GENERAL FAILURE The operating system is unable to carry out the command. The
message is usually followed by specic information. For example,
Printer out of paper. Take the appropriate
action.
HARD-DISK DRIVE CONFIGURATION ERROR The computer cannot identify the drive type. Shut down the
computer, remove the hard drive, and boot the computer from an
optical drive. Then, shut down the computer, reinstall the hard
drive, and restart the computer. Run the Hard Disk Drive tests in
Dell Diagnostics.
HARD-DISK DRIVE CONTROLLER FAILURE 0 The hard drive does not respond to commands from the computer.
Shut down the computer, remove the hard drive, and boot the
computer from an optical drive. Then, shut down the computer,
reinstall the hard drive, and restart the computer. If the problem
persists, try another drive. Run the Hard Disk Drive tests in Dell
Diagnostics.
HARD-DISK DRIVE FAILURE The hard drive does not respond to commands from the computer.
Shut down the computer, remove the hard drive, and boot the
computer from an optical drive. Then, shut down the computer,
reinstall the hard drive, and restart the computer. If the problem
persists, try another drive. Run the Hard Disk Drive tests in Dell
Diagnostics.
HARD-DISK DRIVE READ FAILURE The hard drive may be defective. Shut down the computer, remove
the hard drive, and boot the computer from an optical. Then, shut
down the computer, reinstall the hard drive, and restart the
54 Troubleshooting
Error messages Description
computer. If the problem persists, try another drive. Run the Hard
Disk Drive tests in Dell Diagnostics.
INSERT BOOTABLE MEDIA The operating system is trying to boot to non-bootable media, such
as an optical drive. Insert bootable media.
INVALID CONFIGURATION INFORMATION-PLEASE RUN
SYSTEM SETUP PROGRAM
The system conguration information does not match the hardware
conguration. The message is most likely to occur after a memory
module is installed. Correct the appropriate options in the system
setup program.
KEYBOARD CLOCK LINE FAILURE For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
KEYBOARD CONTROLLER FAILURE For external keyboards, check the cable connection. Restart the
computer, and avoid touching the keyboard or the mouse during the
boot routine. Run the Keyboard Controller test in Dell Diagnostics.
KEYBOARD DATA LINE FAILURE For external keyboards, check the cable connection. Run the
Keyboard Controller test in Dell Diagnostics.
KEYBOARD STUCK KEY FAILURE For external keyboards or keypads, check the cable connection.
Restart the computer, and avoid touching the keyboard or keys
during the boot routine. Run the Stuck Key test in Dell
Diagnostics.
LICENSED CONTENT IS NOT ACCESSIBLE IN
MEDIADIRECT
Dell MediaDirect cannot verify the Digital Rights Management
(DRM) restrictions on the le, so the le cannot be played.
MEMORY ADDRESS LINE FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
MEMORY ALLOCATION ERROR The software you are attempting to run is conicting with the
operating system, another program, or a utility. Shut down the
computer, wait for 30 seconds, and then restart it. Run the program
again. If the error message still appears, see the software
documentation.
MEMORY DOUBLE WORD LOGIC FAILURE AT ADDRESS,
READ VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
MEMORY ODD/EVEN LOGIC FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
MEMORY WRITE/READ FAILURE AT ADDRESS, READ
VALUE EXPECTING VALUE
A memory module may be faulty or improperly seated. Reinstall the
memory module or, if necessary, replace it.
NO BOOT DEVICE AVAILABLE The computer cannot nd the hard drive. If the hard drive is your
boot device, ensure that the drive is installed, properly seated, and
partitioned as a boot device.
NO BOOT SECTOR ON HARD DRIVE The operating system may be corrupted, Contact Dell.
NO TIMER TICK INTERRUPT A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
NOT ENOUGH MEMORY OR RESOURCES. EXIT SOME
PROGRAMS AND TRY AGAIN
You have too many programs open. Close all windows and open the
program that you want to use.
OPERATING SYSTEM NOT FOUND Reinstall the operating system. If the problem persists, Contact
Dell.
OPTIONAL ROM BAD CHECKSUM The optional ROM has failed. Contact Dell.
Troubleshooting 55
Error messages Description
SECTOR NOT FOUND The operating system cannot locate a sector on the hard drive. You
may have a defective sector or corrupted File Allocation Table (FAT)
on the hard drive. Run the Windows error-checking utility to check
the le structure on the hard drive. See Windows Help and
Support for instructions (click Start > Help and Support). If a large
number of sectors are defective, back up the data (if possible), and
then format the hard drive.
SEEK ERROR The operating system cannot nd a specic track on the hard drive.
SHUTDOWN FAILURE A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics. If the message reappears,
Contact Dell.
TIME-OF-DAY CLOCK LOST POWER System conguration settings are corrupted. Connect your
computer to an electrical outlet to charge the battery. If the
problem persists, try to restore the data by entering the System
Setup program, then immediately exit the program. If the message
reappears, Contact Dell.
TIME-OF-DAY CLOCK STOPPED The reserve battery that supports the system conguration settings
may require recharging. Connect your computer to an electrical
outlet to charge the battery. If the problem persists, Contact Dell.
TIME-OF-DAY NOT SET-PLEASE RUN THE SYSTEM SETUP
PROGRAM
The time or date stored in the system setup program does not
match the system clock. Correct the settings for the Date and
Time options.
TIMER CHIP COUNTER 2 FAILED A chip on the system board may be malfunctioning. Run the
System Set tests in Dell Diagnostics.
UNEXPECTED INTERRUPT IN PROTECTED MODE The keyboard controller may be malfunctioning, or a memory
module may be loose. Run the System Memory tests and the
Keyboard Controller test in Dell Diagnostics or Contact Dell.
X:\ IS NOT ACCESSIBLE. THE DEVICE IS NOT READY Insert a disk into the drive and try again.
System error messages
Table 5. System error messages
System message Description
Alert! Previous attempts at booting this system
have failed at checkpoint [nnnn]. For help in
resolving this problem, please note this
checkpoint and contact Dell Technical Support
The computer failed to complete the boot routine three consecutive
times for the same error.
CMOS checksum error RTC is reset, BIOS Setup default has been loaded.
CPU fan failure CPU fan has failed.
System fan failure System fan has failed.
Hard-disk drive failure Possible hard disk drive failure during POST.
Keyboard failure Keyboard failure or loose cable. If reseating the cable does not solve
the problem, replace the keyboard.
No boot device available No bootable partition on hard disk drive, the hard disk drive cable is
loose, or no bootable device exists.
56 Troubleshooting
System message Description
• If the hard drive is your boot device, ensure that the cables are
connected and that the drive is installed properly and
partitioned as a boot device.
• Enter system setup and ensure that the boot sequence
information is correct.
No timer tick interrupt A chip on the system board might be malfunctioning or
motherboard failure.
NOTICE - Hard Drive SELF MONITORING SYSTEM has
reported that a parameter has exceeded its
normal operating range. Dell recommends that
you back up your data regularly. A parameter
out of range may or may not indicate a
potential hard drive problem
S.M.A.R.T error, possible hard disk drive failure.
Real Time Clock reset
The Real Time Clock (RTC) reset function allows you to recover your Dell system from No POST/No Boot/No Power situations. To initiate
the RTC reset on the system make sure system is in a power-o state and is connected to power source . Press and hold the power button
for 25 seconds and then release the power button. Go to how to reset real time clock.
NOTE: If AC power is disconnected from the system during the process or the power button is held longer than 40 seconds, the
RTC reset process is aborted.
The RTC reset will reset the BIOS to Defaults, un-provision Intel vPro and reset the system date and time. The following items are
unaected by the RTC reset:
• Service Tag
• Asset Tag
• Ownership Tag
• Admin Password
• System Password
• HDD Password
• TPM on and Active
• Key Databases
• System Logs
The following items may or may not reset based on your custom BIOS setting selections:
• The Boot List
• Enable Legacy OROMs
• Secure Boot Enable
• Allow BIOS Downgrade
Flashing the BIOS
You may need to ash (update) the BIOS when an update is available or when you replace the system board.
Follow these steps to ash the BIOS:
1 Turn on your computer.
2 Go to www.dell.com/support.
3 Click Product support, enter the Service Tag of your computer, and then click Submit.
NOTE: If you do not have the Service Tag, use the auto-detect feature or manually browse for your computer model.
Troubleshooting 57
4 Click Drivers & downloads > Find it myself.
5 Select the operating system installed on your computer.
6 Scroll down the page and expand BIOS.
7 Click Download to download the latest version of the BIOS for your computer.
8 After the download is complete, navigate to the folder where you saved the BIOS update le.
9 Double-click the BIOS update le icon and follow the instructions on the screen.
Flashing the BIOS from the F12 One-Time boot menu
Updating your system BIOS using a BIOS update .exe le copied to a FAT32 USB key and booting from the F12 one time boot menu.
BIOS Update
You can run the BIOS update le from Windows using a bootable USB key or you can also update the BIOS from the F12 One-Time boot
menu on the system.
Most Dell systems built after 2012 have this capability and you can conrm by booting your system to the F12 One-Time Boot Menu to see
if BIOS FLASH UPDATE is listed as a boot option for your system. If the option is listed, then the BIOS supports this BIOS update option.
NOTE: Only systems with BIOS Flash Update option in the F12 One-Time Boot Menu can use this function.
Updating from the One-Time Boot Menu
To update your BIOS from the F12 One-Time boot menu, you will need:
• USB key formatted to the FAT32 le system (key does not have to be bootable)
• BIOS executable le that you downloaded from the Dell Support website and copied to the root of the USB key
• AC power adapter connected to the system
• Functional system battery to ash the BIOS
Perform the following steps to execute the BIOS update ash process from the F12 menu:
CAUTION: Do not power o the system during the BIOS update process. Powering o the system could make the system fail to
boot.
1 From a power o state, insert the USB key where you copied the ash into a USB port of the system .
2 Power on the system and press the F12 key to access the One-Time Boot Menu, Highlight BIOS Update using the mouse or arrow
keys then press Enter.
58 Troubleshooting
3 The Bios ash menu will open then click the Flash from le.
4 Select external USB device
5 Once the le is selected, Double click the ash target le, then press submit .
Troubleshooting 59
6 Click the Update BIOS then system will reboot to ash the BIOS.
7 Once complete, the system will reboot and the BIOS update process is completed.
Flashing BIOS (USB key)
1 Follow the procedure from step 1 to step 7 in "Flashing the BIOS" to download the latest BIOS setup program le.
2 Create a bootable USB drive. For more information see the knowledge base article SLN143196 at www.dell.com/support.
3 Copy the BIOS setup program le to the bootable USB drive.
4 Connect the bootable USB drive to the computer that needs the BIOS update.
5 Restart the computer and press F12 when the Dell logo is displayed on the screen.
6 Boot to the USB drive from the One Time Boot Menu.
7 Type the BIOS setup program lename and press Enter.
8 The BIOS Update Utility appears. Follow the instructions on the screen to complete the BIOS update.
60 Troubleshooting
Wi-Fi power cycle
If your computer is unable to access the internet due to Wi-Fi connectivity issues a Wi-Fi power cycle procedure may be performed. The
following procedure provides the instructions on how to conduct a Wi-Fi power cycle:
NOTE: Some ISPs (Internet Service Providers) provide a modem/router combo device.
1 Turn o your computer.
2 Turn o the modem.
3 Turn o the wireless router.
4 Wait for 30 seconds.
5 Turn on the wireless router.
6 Turn on the modem.
7 Turn on your computer.
Flea power release
Flea power is the residual static electricity that remains on the computer even after it has been powered o and the battery has been
removed. The following procedure provides the instructions on how to conduct ea power release:
1 Turn o your computer.
2 Remove the base cover.
3 Press and hold the power button for 15 seconds to drain the ea power.
4 Replace the base cover.
5 Turn on your computer.
Troubleshooting 61
Getting help
Contacting Dell
NOTE: If you do not have an active Internet connection, you can nd contact information on your purchase invoice, packing slip,
bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by country and product, and some services
may not be available in your area. To contact Dell for sales, technical support, or customer service issues:
1 Go to Dell.com/support.
2 Select your support category.
3 Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
4 Select the appropriate service or support link based on your need.
5
62 Getting help