Table of Contents
- Before You Begin
- After Working Inside Your Computer
- Technical Overview
- Removing the Computer Cover
- Replacing the Computer Cover
- Removing the Memory Module(s)
- Replacing the Memory Module(s)
- Removing the Front Bezel
- Replacing the Front Bezel
- Removing the Graphics-Card Bracket (optional)
- Replacing the Graphics-Card Bracket (optional)
- Removing the Graphics Card
- Replacing the Graphics Card
- Removing the Wireless Mini-Card
- Replacing the Wireless Mini-Card
- Removing the mSATA Drive
- Replacing the mSATA Drive
- Removing the Primary Hard-Drive
- Replacing the Primary Hard-Drive
- Removing the Hard-Drive Cage
- Replacing the Hard-Drive Cage
- Removing the Secondary Hard-Drive (optional)
- Replacing the Secondary Hard-Drive (optional)
- Installing a third Hard-Drive (optional)
- Removing the Optical Drive
- Replacing the Optical Drive
- Removing the Top Cover
- Replacing the Top Cover
- Removing the Media-Card Reader
- Replacing the Media-Card Reader
- Removing the Top I/O Panel
- Replacing the Top I/O Panel
- Removing the Front USB Panel
- Replacing the Front USB Panel
- Removing the Power Button Module
- Replacing the Power Button Module
- Removing the Chassis Fan
- Replacing the Chassis Fan
- Removing the Processor Fan and Heat-Sink
- Replacing the Processor Fan and Heat-Sink
- Removing the Processor
- Replacing the Processor
- Removing the Coin-Cell Battery
- Replacing the Coin-Cell Battery
- Removing the Power-Supply Unit
- Replacing the Power-Supply Unit
- Removing the System Board
- Replacing the System Board
- System Setup
- Flashing the BIOS
- More Information
DELL 8700 User Manual
Displayed below is the user manual for 8700 by DELL which is a product in the PCs/Workstations category. This manual has pages.
Related Manuals
XPS 8700
Owner’s Manual
Computer model: XPS 8700
Regulatory model: D14M
Regulatory type: D14M001
OM_Book.book Page 1 Tuesday, April 30, 2013 6:07 PM
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better
use of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of
data if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
____________________
© 2013 Dell Inc.
Trademarks used in this text: Dell™, the DELL logo, and XPS™ are trademarks of Dell Inc.;
Microsoft® and Windows®
are registered trademarks of Microsoft Corporation in the United
States and/or other countries; Bluetooth® is a registered trademark owned by Bluetooth SIG,
Inc. and is used by Dell under license; Intel® and Intel SpeedStep® are registered trademarks
of Intel Corporation in the U.S. and/or other countries.
2013 - 04 Rev. A00
OM_Book.book Page 2 Tuesday, April 30, 2013 6:07 PM
Contents | 3
Contents
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Turn Off Your Computer and Connected Devices. . . . . 9
Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . 10
Recommended Tools. . . . . . . . . . . . . . . . . . . . . . . 10
After Working Inside Your Computer . . . . . . . . . . 11
Technical Overview . . . . . . . . . . . . . . . . . . . . . . . . 12
Inside View of Your Computer. . . . . . . . . . . . . . . . . 12
System-Board Components . . . . . . . . . . . . . . . . . . 13
Removing the Computer Cover . . . . . . . . . . . . . . 15
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Replacing the Computer Cover . . . . . . . . . . . . . . 16
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Removing the Memory Module(s). . . . . . . . . . . . . 17
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Replacing the Memory Module(s). . . . . . . . . . . . . 18
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Removing the Front Bezel . . . . . . . . . . . . . . . . . . . 21
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Replacing the Front Bezel . . . . . . . . . . . . . . . . . . . 23
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
OM_Book.book Page 3 Tuesday, April 30, 2013 6:07 PM
4 | Contents
Removing the Graphics-Card
Bracket (optional). . . . . . . . . . . . . . . . . . . . . . . . . . 24
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Replacing the Graphics-Card
Bracket (optional). . . . . . . . . . . . . . . . . . . . . . . . . . 25
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Removing the Graphics Card . . . . . . . . . . . . . . . . 26
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Replacing the Graphics Card . . . . . . . . . . . . . . . . 29
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Removing the Wireless Mini-Card . . . . . . . . . . . . 30
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Replacing the Wireless Mini-Card . . . . . . . . . . . . 32
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Removing the mSATA Drive. . . . . . . . . . . . . . . . . . 33
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Replacing the mSATA Drive . . . . . . . . . . . . . . . . . . 34
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Removing the Primary Hard-Drive . . . . . . . . . . . . 35
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
OM_Book.book Page 4 Tuesday, April 30, 2013 6:07 PM
Contents | 5
Replacing the Primary Hard-Drive . . . . . . . . . . . . 37
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Removing the Hard-Drive Cage . . . . . . . . . . . . . . 38
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Replacing the Hard-Drive Cage . . . . . . . . . . . . . . 39
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Removing the Secondary
Hard-Drive (optional) . . . . . . . . . . . . . . . . . . . . . . 40
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Replacing the Secondary
Hard-Drive (optional) . . . . . . . . . . . . . . . . . . . . . . 41
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installing a third Hard-Drive (optional) . . . . . . . . 42
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Removing the Optical Drive . . . . . . . . . . . . . . . . . 45
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Replacing the Optical Drive . . . . . . . . . . . . . . . . . 46
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Removing the Top Cover. . . . . . . . . . . . . . . . . . . . 47
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
OM_Book.book Page 5 Tuesday, April 30, 2013 6:07 PM
6 | Contents
Replacing the Top Cover . . . . . . . . . . . . . . . . . . . . 48
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Removing the Media-Card Reader . . . . . . . . . . . . 49
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Replacing the Media-Card Reader . . . . . . . . . . . . 50
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Removing the Top I/O Panel . . . . . . . . . . . . . . . . . 51
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Replacing the Top I/O Panel . . . . . . . . . . . . . . . . . 53
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Removing the Front USB Panel . . . . . . . . . . . . . . . 54
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Replacing the Front USB Panel . . . . . . . . . . . . . . . 56
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Removing the Power Button Module . . . . . . . . . . 57
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Replacing the Power Button Module . . . . . . . . . . 59
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Removing the Chassis Fan. . . . . . . . . . . . . . . . . . . 60
Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
OM_Book.book Page 6 Tuesday, April 30, 2013 6:07 PM
Contents | 7
Replacing the Chassis Fan. . . . . . . . . . . . . . . . . . . 61
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Removing the Processor Fan and Heat-Sink . . . . 62
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Replacing the Processor Fan and Heat-Sink . . . . 64
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Removing the Processor . . . . . . . . . . . . . . . . . . . . 65
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Replacing the Processor . . . . . . . . . . . . . . . . . . . . 67
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Removing the Coin-Cell Battery . . . . . . . . . . . . . 69
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Replacing the Coin-Cell Battery. . . . . . . . . . . . . . 70
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Removing the Power-Supply Unit . . . . . . . . . . . . 71
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Replacing the Power-Supply Unit . . . . . . . . . . . . 72
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Postrequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Removing the System Board. . . . . . . . . . . . . . . . . 73
Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
OM_Book.book Page 7 Tuesday, April 30, 2013 6:07 PM
8 | Contents
Replacing the System Board . . . . . . . . . . . . . . . . . 75
Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Postrequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Entering the Service Tag in system setup. . . . . . . . . . 75
System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Entering System Setup . . . . . . . . . . . . . . . . . . . . . . 76
Changing Boot Sequence. . . . . . . . . . . . . . . . . . . . 82
Clearing Forgotten Passwords. . . . . . . . . . . . . . . . . 83
Clearing CMOS Settings . . . . . . . . . . . . . . . . . . . . . 84
Flashing the BIOS . . . . . . . . . . . . . . . . . . . . . . . . . . 85
More Information. . . . . . . . . . . . . . . . . . . . . . . . . . 86
OM_Book.book Page 8 Tuesday, April 30, 2013 6:07 PM
Before You Begin | 9
Before You Begin
Turn Off Your Computer and Connected Devices
CAUTION: To avoid losing data, save and close all open files and exit all open
programs before you turn off your computer.
1Save and close all open files and exit all open programs.
2Move your mouse pointer to the upper-right or lower-right corner of the screen to
open the Charms sidebar, and then click Settings→ Power→ Shut down.
NOTE: If you are using a different operating system, see the documentation
of your operating system for shut-down instructions.
3Disconnect your computer and all attached devices from their electrical outlets.
4Disconnect all telephone cables, network cables, and attached devices from
your computer.
5Press and hold the power button for 5 seconds after the computer is unplugged to
ground the system board.
OM_Book.book Page 9 Tuesday, April 30, 2013 6:07 PM
10 | Before You Begin
Safety Instructions
Use the following safety guidelines to protect your computer from potential damage and
ensure your personal safety.
WARNING: Before working inside your computer, read the safety information
that shipped with your computer. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
WARNING: Disconnect all power sources before opening the computer cover or
panels. After you finish working inside the computer, replace all covers, panels,
and screws before connecting to the power source.
CAUTION: To avoid damaging the computer, ensure that the work surface is flat
and clean.
CAUTION: To avoid damaging the components and cards, handle them by their
edges and avoid touching pins and contacts.
CAUTION: Only a certified service technician is authorized to remove the
computer cover and access any of the components inside the computer.
See the safety instructions for complete information about safety precautions,
working inside your computer, and protecting against electrostatic discharge.
CAUTION: Before touching anything inside your computer, ground yourself by
touching an unpainted metal surface, such as the metal at the back of the
computer. While you work, periodically touch an unpainted metal surface to
dissipate static electricity, which could harm internal components.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab,
not on the cable itself. Some cables have connectors with locking tabs or
thumb-screws that you must disengage before disconnecting the cable.
When disconnecting cables, keep them evenly aligned to avoid bending any
connector pins. When connecting cables, ensure that the connectors and ports
are correctly oriented and aligned.
CAUTION: To disconnect a network cable, first unplug the cable from your
computer and then unplug the cable from the network device.
CAUTION: Press and eject any installed card from the media-card reader.
Recommended Tools
The procedures in this document may require the following tools:
•Phillips screwdriver
•Plastic scribe
OM_Book.book Page 10 Tuesday, April 30, 2013 6:07 PM
After Working Inside Your Computer | 11
After Working Inside Your Computer
After you complete the replacement procedures, ensure the following:
•Replace all screws and ensure that no stray screws remain inside your computer.
•Place the computer in an upright position.
•Connect any external devices, cables, cards, and any other part(s) you removed
before working on your computer.
•Connect your computer and all attached devices to their electrical outlets.
CAUTION: Before turning on your computer, replace all screws and ensure
that no stray screws remain inside the computer. Failure to do so may damage
your computer.
OM_Book.book Page 11 Tuesday, April 30, 2013 6:07 PM
12 | Technical Overview
Technical Overview
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Inside View of Your Computer
1 front bezel 2 primary hard-drive
3 secondary hard-drive 4 graphics-card bracket (optional)
5 graphics card 6 card retention bracket
7 power supply 8 optical drive
7
5
8
4
1
23
6
OM_Book.book Page 12 Tuesday, April 30, 2013 6:07 PM
Technical Overview | 13
System-Board Components
1 chassis fan connector
(SYS_FAN 1)
2 power connector (PWRCONN1)
3 processor socket 4 processor fan connector
(CPU_FAN)
5 memory module connector
(DIMM3)
6 memory module connector
(DIMM1)
7 memory module connector
(DIMM4)
8 memory module connector
(DIMM2)
9 main power connector
(PWR1)
10 CMOS reset jumper (RTCRST)
123455 678
9
10
11
13
14
15
16
17
18
19
20
2122
23
24
25
26
27
29
28
12
OM_Book.book Page 13 Tuesday, April 30, 2013 6:07 PM
14 | Technical Overview
11 mSATA slot (MSATA1) 12 SATA 3.0 (6 Gb/s) drive connector
(SATA 2)
13 SATA 3.0 (6 Gb/s) drive connector
(SATA 4)
14 SATA 3.0 (6 Gb/s) drive connector
(SATA 3)
15 front panel USB connector
(F_USB3)
16 front panel USB connector
(F_USB2)
17 SATA 3.0 (6 Gb/s) drive connector
(SATA 1)
18 power button connector
(F_PANEL)
19 front panel USB connector
(F_USB1)
20 password reset jumper
(PSWD)
21 SATA 3.0 (6 Gb/s) drive connector
(SATA 0)
22 front panel USB connector
(F_USB4)
23 front panel audio connector
(F_AUDIO1)
24 PCI-Express x1 card slot
(PCI-EX1_4)
25 PCI-Express x1 card slot
(PCI-EX1_2)
26 PCI-Express x1 card slot
(PCI-EX1_1)
27 PCI-Express x16 card slot
(PCI-EX16_1)
28 Mini-Card slot
(PCIE_MINICARD)
29 battery socket (BATTERY)
OM_Book.book Page 14 Tuesday, April 30, 2013 6:07 PM
Removing the Computer Cover | 15
Removing the Computer Cover
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1 Lay the computer on its side with the computer cover facing up.
2Remove the thumbscrew that secures the computer cover to the chassis, using a
screw driver, if necessary.
3Release the computer cover by sliding it away from the front of the computer.
4Lift the cover away from the computer and set it aside in a secure location.
1 thumbscrew 2 computer cover
1
2
OM_Book.book Page 15 Tuesday, April 30, 2013 6:07 PM
16 | Replacing the Computer Cover
Replacing the Computer Cover
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Connect all the cables and fold the cables out of the way.
2Ensure that no tools or extra parts are left inside the computer.
3Align the tabs at the bottom of the computer cover with the slots located along the
edge of the chassis.
4Press the computer cover down and slide it towards the front of the computer.
5Replace the thumbscrew that secures the computer cover to the chassis.
6Place the computer in an upright position.
Postrequisites
Follow the instructions in "After Working Inside Your Computer" on page 11.
OM_Book.book Page 16 Tuesday, April 30, 2013 6:07 PM
Removing the Memory Module(s) | 17
Removing the Memory Module(s)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the graphics card. See "Removing the Graphics Card" on page 26.
Procedure
WARNING: The memory module(s) may become hot during normal operation.
Allow the memory module(s) to cool before touching them.
1Press out the securing clip at each end of the memory-module connector.
NOTE: If the memory module is difficult to remove, gently ease the memory
module back and forth to remove it from the connector.
2Grasp the memory module and pull it upward.
1 memory-module connector 2 memory module
3 securing clips (2)
1
2
3
OM_Book.book Page 17 Tuesday, April 30, 2013 6:07 PM
18 | Replacing the Memory Module(s)
Replacing the Memory Module(s)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
CAUTION: If the memory module is not installed correctly, your computer may
not boot.
CAUTION: If you remove the original memory module(s) from your computer
during a memory upgrade, keep them separate from any new module(s) that you
may have, even if you purchased the new module(s) from Dell. If possible, do not
pair an original memory module with a new memory module. Otherwise, your
computer may not start properly.
The recommended memory configurations are:
matched memory modules installed in DIMM connectors 1 and 2 and another
matched memory modules installed in DIMM connectors 3 and 4.
OM_Book.book Page 18 Tuesday, April 30, 2013 6:07 PM
Replacing the Memory Module(s) | 19
1Press out the securing clip at each end of the memory-module connector.
2Align the notch on the bottom of the memory module with the tab on the
memory-module connector.
1 cutouts (2) 2 memory-module connector
3tab 4notch
5memory module
1
2
3
4
5
OM_Book.book Page 19 Tuesday, April 30, 2013 6:07 PM
20 | Replacing the Memory Module(s)
3Insert the memory module into the memory-module connector until the memory
module snaps into position.
If you insert the memory module correctly, the securing clips snap into the cutouts
at each end of the memory module.
Postrequisites
1Replace the graphics card. See "Replacing the Graphics Card" on page 29.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
1 securing clip (snapped in position) 2 memory-module connector
3memory module
1
2
3
OM_Book.book Page 20 Tuesday, April 30, 2013 6:07 PM
Removing the Front Bezel | 21
Removing the Front Bezel
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
OM_Book.book Page 21 Tuesday, April 30, 2013 6:07 PM
22 | Removing the Front Bezel
Procedure
1Place the computer in an upright position.
2Grasp and release the front bezel tabs sequentially, one at a time by moving them
outward from the front panel.
3Rotate and pull the front bezel away from the front of the computer to release the
front bezel clamps from the front panel slots.
1 front bezel 2 front bezel tabs (4)
3 front bezel clamps (3) 4 front panel slots (3)
5 front panel
1
2
3
4
5
OM_Book.book Page 22 Tuesday, April 30, 2013 6:07 PM
Replacing the Front Bezel | 23
Replacing the Front Bezel
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align and insert the front bezel clamps into the front panel slots.
2Rotate the front bezel towards the computer until the front bezel tabs snap into
place.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 23 Tuesday, April 30, 2013 6:07 PM
24 | Removing the Graphics-Card Bracket (optional)
Removing the Graphics-Card Bracket (optional)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Remove the screws that secure the graphics-card bracket to the chassis.
2Lift the graphics-card bracket off the chassis.
3Set the graphics-card bracket aside in a secure location.
1 screws (2) 2 graphics-card bracket
1
2
OM_Book.book Page 24 Tuesday, April 30, 2013 6:07 PM
Replacing the Graphics-Card Bracket (optional) | 25
Replacing the Graphics-Card Bracket (optional)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the screw holes on the graphics-card bracket with the screw holes on the
chassis.
2Replace the screws that secure the graphics-card bracket to the chassis..
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 25 Tuesday, April 30, 2013 6:07 PM
26 | Removing the Graphics Card
Removing the Graphics Card
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
The system board of your computer is equipped with one PCI-Express x16
connector to install graphics card. To locate the PCI-Express x16 connector on
the system board, see "System-Board Components" on page 13.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the graphics-card bracket, if applicable. See "Removing the Graphics-Card
Bracket (optional)" on page 24.
OM_Book.book Page 26 Tuesday, April 30, 2013 6:07 PM
Removing the Graphics Card | 27
Procedure
1Remove the screw that secures the card-retention bracket to the chassis.
2Lift the card-retention bracket and set it aside in a secure location.
NOTE: Your graphics card may have power-cable connectors.
3Press the releasing clips on the power-cable connectors and disconnect the power
cable from the graphics card, if applicable.
4Locate the graphics card (PCI-Express x16 card) on the system board.
See "System-Board Components" on page 13.
NOTE: The appearence of the securing tab may be different on your
computer.
1power cable 2screw
3 card-retention bracket
3
2
1
OM_Book.book Page 27 Tuesday, April 30, 2013 6:07 PM
28 | Removing the Graphics Card
5Press and hold the securing tab on the card connector, grasp the card by its top
corners, and then ease the card out of the card connector.
1 securing tab 2 graphics card
1
2
OM_Book.book Page 28 Tuesday, April 30, 2013 6:07 PM
Replacing the Graphics Card | 29
Replacing the Graphics Card
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the graphics card with the PCI-Express x16 card connector on the system
board.
2Place the card in the connector and press down firmly. Ensure that the card is firmly
seated in the slot.
3Connect the power cable to the graphics card, if applicable.
4Replace the card-retention bracket, ensuring that:
•The guide clamp is aligned with the guide notch.
•The top of all cards and filler brackets are flush with the alignment bar.
•The notch on top of the card or filler bracket fits around the alignment guide.
5Replace the screw that secures the card-retention bracket.
Postrequisites
1Replace the graphics-card bracket, if applicable. See "Replacing the Graphics-Card
Bracket (optional)" on page 25.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 29 Tuesday, April 30, 2013 6:07 PM
30 | Removing the Wireless Mini-Card
Removing the Wireless Mini-Card
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Disconnect the antenna cables from the wireless mini-card.
2Remove the screws that secure the wireless mini-card to the system board.
1 screws (2) 2 antenna cables (2)
1
2
OM_Book.book Page 30 Tuesday, April 30, 2013 6:07 PM
Removing the Wireless Mini-Card | 31
3Slide and remove the wireless mini-card out of the wireless mini-card connector.
1 wireless mini-card connector 2 wireless mini-card
OM_Book.book Page 31 Tuesday, April 30, 2013 6:07 PM
32 | Replacing the Wireless Mini-Card
Replacing the Wireless Mini-Card
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
CAUTION: To avoid damage to the wireless mini-card, ensure that no cables are
placed under the wireless mini-card.
1Align the notch on the wireless mini-card with the tab on the wireless
mini-card connector.
2Insert the wireless mini-card at a 45-degree angle into the wireless
mini-card connector.
3Press the outer end of the wireless mini-card down and replace the screws
that secure the wireless mini-card to the system board.
4Connect the antenna cables to the wireless mini-card.
The following table provides the wireless-antenna cable color schemes for
the wireless mini-cards supported by your computer.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
Connectors on the mini-card Wireless-antenna cable color schemes
WLAN + Bluetooth (two cables)
Main WLAN + Bluetooth (white triangle)
Auxiliary WLAN + Bluetooth (black triangle)
white
black
OM_Book.book Page 32 Tuesday, April 30, 2013 6:07 PM
Removing the mSATA Drive | 33
Removing the mSATA Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Remove the screws that secure the mSATA drive to the system board.
2Lift the mSATA drive away from the system-board connector.
1 screws (2) 2 mSATA drive
3 mSATA-drive connector
123
OM_Book.book Page 33 Tuesday, April 30, 2013 6:07 PM
34 | Replacing the mSATA Drive
Replacing the mSATA Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the notch on the mSATA drive with the tab on the
system-board connector.
2Insert the mSATA drive at a 45-degree angle into the
system-board connector.
3Press the other end of the mSATA drive down and replace the screws that secure
the mSATA drive to the systemboard.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 34 Tuesday, April 30, 2013 6:07 PM
Removing the Primary Hard-Drive | 35
Removing the Primary Hard-Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
WARNING: If you remove the hard drive from the computer when the drive is
hot, do not touch the metal housing of the hard drive.
CAUTION: To avoid data loss, do not remove the hard drive while the computer is
on or in Sleep state.
CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
OM_Book.book Page 35 Tuesday, April 30, 2013 6:07 PM
36 | Removing the Primary Hard-Drive
Procedure
1Disconnect the power and data cables from the primary hard-drive.
2Remove the screws that secure the hard drive to the chassis.
3Slide the hard drive out towards the back of the computer.
1 power cable 2 data cable
3 primary hard-drive 4 screws (4)
1
2
3
4
OM_Book.book Page 36 Tuesday, April 30, 2013 6:07 PM
Replacing the Primary Hard-Drive | 37
Replacing the Primary Hard-Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Slide the primary hard-drive into the hard-drive cage.
2Align the screw holes on the primary hard-drive with the screw holes on the chassis.
3Replace the screws that secure the primary hard-drive to the chassis.
4Connect the power and data cables to the primary hard-drive.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 37 Tuesday, April 30, 2013 6:07 PM
38 | Removing the Hard-Drive Cage
Removing the Hard-Drive Cage
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the primary hard-drive. See "Removing the Primary Hard-Drive" on
page 35.
Procedure
1If applicable, disconnect the power and data cables from the secondary hard-drive.
2Remove the screws that secure the hard-drive cage to the chassis.
3Slide and lift the hard-drive cage away from the chassis.
1 screws (3) 2 hard-drive cage
3 power cable 4 data cable
3
4
12
OM_Book.book Page 38 Tuesday, April 30, 2013 6:07 PM
Replacing the Hard-Drive Cage | 39
Replacing the Hard-Drive Cage
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the screw holes on the hard-drive cage with the screw holes on the chassis.
2Replace the screws that secure the hard-drive cage to the chassis.
3If applicable, connect the power and data cables to the secondary hard-drive.
Postrequisites
1Replace the primary hard-drive. See "Replacing the Primary Hard-Drive" on page 37.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 39 Tuesday, April 30, 2013 6:07 PM
40 | Removing the Secondary Hard-Drive (optional)
Removing the Secondary Hard-Drive (optional)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
WARNING: If you remove the hard drive from the computer when the drive is
hot, do not touch the metal housing of the hard drive.
CAUTION: To avoid data loss, do not remove the hard drive while the computer is
on or in Sleep state.
CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the primary hard-drive. See "Removing the Primary Hard-Drive" on
page 35.
3Remove the hard-drive cage. See "Removing the Hard-Drive Cage" on page 38.
Procedure
1Remove the screws that secure the secondary hard-drive to the hard-drive cage.
2Slide the secondary hard-drive out from the hard-drive cage.
1 secondary hard-drive 2 screws (4)
3 hard-drive cage
123
OM_Book.book Page 40 Tuesday, April 30, 2013 6:07 PM
Replacing the Secondary Hard-Drive (optional) | 41
Replacing the Secondary Hard-Drive (optional)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Slide the secondary hard-drive into the hard-drive cage.
2Replace the screws that secure the secondary hard-drive to the hard-drive cage.
Postrequisites
1Replace the hard-drive cage. See "Replacing the Hard-Drive Cage" on page 39.
2Replace the primary hard-drive. See "Replacing the Primary Hard-Drive" on page 37.
3Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 41 Tuesday, April 30, 2013 6:07 PM
42 | Installing a third Hard-Drive (optional)
Installing a third Hard-Drive (optional)
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
CAUTION: Hard drives are fragile. Exercise care when handling the hard drive.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
Procedure
1Insert a screw driver and twist it to remove the break-away metal plate.
2Pull the break-away metal plate away from the chassis.
1 break-away metal plate
1
OM_Book.book Page 42 Tuesday, April 30, 2013 6:07 PM
Installing a third Hard-Drive (optional) | 43
3Gently slide the third hard-drive into the hard-drive bay through the front of the
computer.
1 third hard-drive
1
OM_Book.book Page 43 Tuesday, April 30, 2013 6:07 PM
44 | Installing a third Hard-Drive (optional)
4Replace the screws that secure the third hard-drive to the chassis.
5Connect the power and data cables to the third hard-drive.
Postrequisites
1Replace the front bezel. See "Replacing the Front Bezel" on page 23.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
1 power cable 2 data cable
3screws (2)
1
2
3
OM_Book.book Page 44 Tuesday, April 30, 2013 6:07 PM
Removing the Optical Drive | 45
Removing the Optical Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
Procedure
1Disconnect the power and data cables from the optical drive.
2Remove the screws that secure the optical drive to the chassis.
3Push and slide the optical drive out through the front of the computer.
NOTE: Repeat steps 1 to 3 to remove secondary optical-drive, if applicable.
4Set aside the optical drive in a secure location.
1 power cable 2 data cable
3 screws (2) 4 optical drive
1
2
3
4
OM_Book.book Page 45 Tuesday, April 30, 2013 6:07 PM
46 | Replacing the Optical Drive
Replacing the Optical Drive
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Gently slide the optical drive into the optical-drive bay through the front of the
computer.
2Align the screw holes on the optical drive with the screw holes on the chassis.
3Replace the screws that secure the optical drive to the chassis.
4Connect the power and data cables to the optical drive.
Postrequisites
1Replace the front bezel. See "Replacing the Front Bezel" on page 23.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 46 Tuesday, April 30, 2013 6:07 PM
Removing the Top Cover | 47
Removing the Top Cover
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
Procedure
1Slide and lift the top cover away from top panel.
2Set the top cover aside in a secure location.
1top cover
1
OM_Book.book Page 47 Tuesday, April 30, 2013 6:07 PM
48 | Replacing the Top Cover
Replacing the Top Cover
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the tabs on the top cover with the slots on the top panel.
2Press and slide the top cover towards the back of the computer, until it clicks into
place.
Postrequisites
1Replace the front bezel. See "Replacing the Front Bezel" on page 23.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 48 Tuesday, April 30, 2013 6:07 PM
Removing the Media-Card Reader | 49
Removing the Media-Card Reader
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
3Remove the top cover. See "Removing the Top Cover" on page 47.
Procedure
1Remove the screws that secure the media-card reader to the front panel. The
screws are located below the media-card reader.
2Disconnect the media-card reader cable from the media-card reader.
3Slide and lift the media-card reader to remove it from the top panel.
1 media-card reader cable 2 media-card reader
3 screws (2) 4 front panel
1
2
3
4
OM_Book.book Page 49 Tuesday, April 30, 2013 6:07 PM
50 | Replacing the Media-Card Reader
Replacing the Media-Card Reader
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Gently slide the media-card reader guides into the slots in the top panel
2Replace the screws that secure the media-card reader to the front panel
3Connect the media-card reader cable to the media-card reader.
Postrequisites
1Replace the top cover. See "Replacing the Top Cover" on page 48.
2Replace the front bezel. See "Replacing the Front Bezel" on page 23.
3Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 50 Tuesday, April 30, 2013 6:07 PM
Removing the Top I/O Panel | 51
Removing the Top I/O Panel
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
3Remove the top cover. See "Removing the Top Cover" on page 47.
Procedure
1Disconnect the top I/O panel cables from the system board connectors, F_USB3
and F_AUDIO1. See "System-Board Components" on page 13.
2Remove the screws that secure the top I/O panel to the top panel.
3Slide and lift the top I/O panel from the top panel.
OM_Book.book Page 51 Tuesday, April 30, 2013 6:07 PM
52 | Removing the Top I/O Panel
1 top I/O panel 2 top panel
3 screws (2) 4 USB cable connector (F_USB3)
5 Audio cable connector (F_AUDIO1)
1
3
2
4
5
OM_Book.book Page 52 Tuesday, April 30, 2013 6:07 PM
Replacing the Top I/O Panel | 53
Replacing the Top I/O Panel
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the screw holes on the top I/O panel with the screw holes on the top panel.
2Replace the screws that secure the top I/O panel to the top panel.
3Connect the top I/O panel cables to the system board connectors, F_USB3 and
F_AUDIO1. See "System-Board Components" on page 13.
Postrequisites
1Replace the top cover. See "Replacing the Top Cover" on page 48.
2Replace the front bezel. See "Replacing the Front Bezel" on page 23.
3Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 53 Tuesday, April 30, 2013 6:07 PM
54 | Removing the Front USB Panel
Removing the Front USB Panel
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
Procedure
CAUTION: When sliding the front USB panel out of the computer, be extremely
careful. Carelessness may result in damage to the cable connectors and the cable
routing clips.
NOTE: Note the routing of all cables as you remove them so that you can re-route
them correctly after you replace the front USB panel.
1Disconnect the front USB panel cables from the system board connector F_USB2.
See "System-Board Components" on page 13.
2Remove the screw that secures the front USB panel to the front panel.
3Slide the front USB panel down and pull it away.
OM_Book.book Page 54 Tuesday, April 30, 2013 6:07 PM
Removing the Front USB Panel | 55
1 front USB panel 2 screw
3 USB panel cables
1
2
3
OM_Book.book Page 55 Tuesday, April 30, 2013 6:07 PM
56 | Replacing the Front USB Panel
Replacing the Front USB Panel
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align and slide the front USB panel clamps into the front USB panel clamp slot.
2Replace the screw that secures the front USB panel to the front panel.
3Connect the front USB panel cables to the system board connector F_USB2. See
"System-Board Components" on page 13.
Postrequisites
1Replace the front bezel. See "Replacing the Front Bezel" on page 23.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 56 Tuesday, April 30, 2013 6:07 PM
Removing the Power Button Module | 57
Removing the Power Button Module
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the front bezel. See "Removing the Front Bezel" on page 21.
3Remove the top cover. See "Removing the Top Cover" on page 47.
Procedure
1Disconnect the power button module cable from the system board connector
F_PANEL. See "System-Board Components" on page 13.
2Press the tabs on the power button module and lift the power button module to
release it from the top panel.
OM_Book.book Page 57 Tuesday, April 30, 2013 6:07 PM
58 | Removing the Power Button Module
1 power button module cable 2 power button module tabs (4)
3 power button module
123
OM_Book.book Page 58 Tuesday, April 30, 2013 6:07 PM
Replacing the Power Button Module | 59
Replacing the Power Button Module
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align and push the power button module tabs into the slots on the top panel.
2Connect the power button module cable from the system board connector
F_PANEL. See "System-Board Components" on page 13.
Postrequisites
1Replace the top cover. See "Replacing the Top Cover" on page 48.
2Replace the front bezel. See "Replacing the Front Bezel" on page 23.
3Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 59 Tuesday, April 30, 2013 6:07 PM
60 | Removing the Chassis Fan
Removing the Chassis Fan
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Disconnect the chassis fan cable from the system board connector SYS_FAN1. See
"System-Board Components" on page 13.
2Remove the screws that secure the chassis fan to the chassis.
3Slide and lift the chassis fan away from the computer.
1 chassis fan cable 2 screws (4)
3 chassis fan
1
2
3
OM_Book.book Page 60 Tuesday, April 30, 2013 6:07 PM
Replacing the Chassis Fan | 61
Replacing the Chassis Fan
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Align the screw holes on the chassis fan with the screw holes on the chassis.
2Replace the screws that secure the chassis fan to the chassis.
3Connect the chassis fan cable to the system board connector SYS_FAN1. See
"System-Board Components" on page 13.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 61 Tuesday, April 30, 2013 6:07 PM
62 | Removing the Processor Fan and Heat-Sink
Removing the Processor Fan and Heat-Sink
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
WARNING: The heat sink may be hot during normal operation. Provide sufficient
time for the heat-sink to cool before you touch it.
CAUTION: To ensure maximum cooling for the processor, do not touch the heat
transfer areas on the processor fan and heat-sink assembly. The oils in your skin
can reduce the heat transfer capability of the thermal grease.
CAUTION: The processor fan and heat-sink assembly is a single unit. Do not try to
remove the fan separately.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Disconnect the processor fan cable from the system board connector CPU_FAN.
See "System-Board Components" on page 13.
2Using a flat-blade screwdriver loosen the four captive screws that secure the
processor fan and heat-sink assembly to the system board.
3Lift the processor fan and heat-sink assembly out of the computer.
OM_Book.book Page 62 Tuesday, April 30, 2013 6:07 PM
Removing the Processor Fan and Heat-Sink | 63
1 processor fan cable 2 processor fan and heat-sink assembly
3 captive screws (4)
123
OM_Book.book Page 63 Tuesday, April 30, 2013 6:07 PM
64 | Replacing the Processor Fan and Heat-Sink
Replacing the Processor Fan and Heat-Sink
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Clean the thermal grease from the bottom of the heat-sink.
2Apply new thermal grease to the top of the processor, if applicable.
3Place the processor fan and heat-sink assembly over the processor.
4Align the captive screws on the processor fan and heat-sink assembly with the
screw holes on the system board.
5Tighten the captive screws that secure the processor fan and heat-sink assembly to
the system board
6Connect the processor fan cable to the system board connector CPU_FAN. See
"System-Board Components" on page 13.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 64 Tuesday, April 30, 2013 6:07 PM
Removing the Processor | 65
Removing the Processor
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
CAUTION: Processors are fragile. Handle the processor only by the edges and do
not touch the metal pins.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
WARNING: Despite having a plastic shield, the processor fan and heat-sink
assembly may be very hot during normal operation. Ensure that it has had
sufficient time to cool before you touch it.
NOTE: Unless a new processor fan and heat-sink assembly is required for the
new processor, reuse the original processor fan and heat-sink assembly when
you replace the processor.
2Remove the processor fan and heat-sink. See "Removing the Processor Fan and
Heat-Sink" on page 62.
Procedure
1Press the release-lever down and then pull it outwards to release it from the
securing tab.
2Extend the release-lever completely to open the processor cover.
OM_Book.book Page 65 Tuesday, April 30, 2013 6:07 PM
66 | Removing the Processor
3Gently lift the processor and remove it from the processor socket.
1 release lever 2 securing tab
3 processor cover 4 socket
5 processor
14
3
2
5
OM_Book.book Page 66 Tuesday, April 30, 2013 6:07 PM
Replacing the Processor | 67
Replacing the Processor
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
NOTE: The original thermal grease can be reused if the original processor and
processor heat-sink are reinstalled together. If either the processor or the
processor heat-sink is replaced, use the thermal grease provided in the kit to ensure
that thermal conductivity is achieved. Ensure that the release lever on the processor
socket is fully extended in the open position.
OM_Book.book Page 67 Tuesday, April 30, 2013 6:07 PM
68 | Replacing the Processor
Procedure
1Ensure that the release lever on the processor socket is fully extended in the open
position.
CAUTION: You must position the processor correctly in the processor socket to
avoid permanent damage to the processor.
2Align the notches on the processor with the tabs on the processor socket.
3Align the pin-1 corner on the processor with the pin-1 corner on the
processor socket, and then place the processor in the processor socket.
CAUTION: Ensure that the processor-cover notch is positioned underneath the
alignment post.
4When the processor is fully seated in the socket, close the processor cover.
5Pivot the release-lever down and place it under the tab on the processor cover.
Postrequisites
1Replace the processor fan and heat-sink. See "Replacing the Processor Fan and
Heat-Sink" on page 64.
2Replace the computer cover. See "Replacing the Computer Cover" on page 16.
1 processor pin-1 indicator 2 processor
3 alignment tabs (2) 4 alignment post
5 processor-cover notch 6 processor cover
7release lever
1
2
345
67
OM_Book.book Page 68 Tuesday, April 30, 2013 6:07 PM
Removing the Coin-Cell Battery | 69
Removing the Coin-Cell Battery
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
CAUTION: Removing the coin-cell battery resets the BIOS settings to default.
It is recommended that you note the BIOS settings before removing the coin-cell
battery.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Locate the battery socket on the system board. See "System-Board Components"
on page 13.
2Press the securing clip away from the coin-cell battery until the coin-cell battery
pops out.
3Lift the coin-cell battery out of its socket.
1 coin-cell battery 2 securing clip
12
OM_Book.book Page 69 Tuesday, April 30, 2013 6:07 PM
70 | Replacing the Coin-Cell Battery
Replacing the Coin-Cell Battery
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
WARNING: The battery may explode if installed incorrectly. Replace the battery
only with the same or equivalent type. Discard used batteries according to the
manufacturer’s instructions.
Procedure
Insert a new coin-cell battery (CR2032) into the battery socket with the positive side
facing up, and press the battery into place.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 70 Tuesday, April 30, 2013 6:07 PM
Removing the Power-Supply Unit | 71
Removing the Power-Supply Unit
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
Remove the computer cover. See "Removing the Computer Cover" on page 15.
Procedure
1Disconnect the DC power cables from the system board and the drives. See
"System-Board Components" on page 13.
2Remove the screws that secure the power-supply unit to the chassis.
3Press the power-supply clamps to release the power-supply unit from the chassis.
4Slide and lift the power-supply unit away from the chassis
1 screws (4) 2 power supply
3 power-supply clamps (2)
1
2
3
OM_Book.book Page 71 Tuesday, April 30, 2013 6:07 PM
72 | Replacing the Power-Supply Unit
Replacing the Power-Supply Unit
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Slide the power supply towards the back of the chassis.
2Align the screw holes on the power-supply unit with the screw holes on the chassis.
3Replace the screws that secure the power-supply unit to the chassis.
4Connect the DC power cables to the system board and the drives. See
"System-Board Components" on page 13.
Postrequisites
Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 72 Tuesday, April 30, 2013 6:07 PM
Removing the System Board | 73
Removing the System Board
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Prerequisites
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Remove the wireless mini-card, if applicable. See "Removing the Wireless
Mini-Card" on page 30.
3Remove the memory module(s). See "Removing the Memory Module(s)" on
page 17.
4Remove the graphics card. See "Removing the Graphics Card" on page 26.
5Remove the processor fan and heat-sink assembly. See "Removing the Processor
Fan and Heat-Sink" on page 62.
6Remove the processor. See "Removing the Processor" on page 65.
OM_Book.book Page 73 Tuesday, April 30, 2013 6:07 PM
74 | Removing the System Board
Procedure
NOTE: Your computer’s service tag is stored in the system board. You must enter
the service tag in the BIOS after you replace the system board.
NOTE: Before disconnecting the cables from the system board, note the location
of the connectors, so that you can reconnect them correctly after you replace the
system board.
1Disconnect all the cables connected to the system board.
2Make note of the cable routing and remove the cables from the routing guides.
3Remove the screws that secure the system board to the chassis.
4Lift the system board up and out of the chassis.
1 screws (5) 2 system board
12
OM_Book.book Page 74 Tuesday, April 30, 2013 6:07 PM
Replacing the System Board | 75
Replacing the System Board
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
Procedure
1Gently place the system board into the chassis and slide it towards the back of the
computer.
2Replace the screws that secure the system board to the chassis.
3Route and connect the cables that you disconnected from the system board.
NOTE: For information on system board connectors, See "System-Board
Components" on page 13.
Postrequisites
1Replace the processor. See "Replacing the Processor" on page 67.
2Replace the processor fan and heat-sink assembly. See "Replacing the Processor
Fan and Heat-Sink" on page 64.
3Replace the graphics card. See "Replacing the Graphics Card" on page 29.
4Replace the memory module(s). See "Replacing the Memory Module(s)" on page 18.
5Replace the wireless mini-card, if applicable. See "Replacing the Wireless
Mini-Card" on page 32.
6Replace the computer cover. See "Replacing the Computer Cover" on page 16.
Entering the Service Tag in system setup
1Turn on the computer.
2Press <F2> during POST to enter the system setup program.
3Navigate to the Main tab and enter the Service Tag in the Service Tag Input field. See
"System Setup" on page 76.
OM_Book.book Page 75 Tuesday, April 30, 2013 6:07 PM
76 | System Setup
System Setup
Overview
Use system setup to:
•Get information about the hardware installed in your computer, such as the
amount of RAM, the size of the hard drive, and so on
•Change the system configuration information
•Set or change a user-selectable option, such as the user password, type of
hard drive installed, enabling or disabling base devices, and so on
CAUTION: Unless you are an expert computer user, do not change the settings in
the system setup program. Certain changes can make your computer work
incorrectly.
NOTE: Before you change system setup, it is recommended that you write down
the system setup screen information for future reference.
Entering System Setup
1Turn on (or restart) your computer.
2During POST, when the DELL logo is displayed, watch for the F2 prompt to appear
and then press <F2> immediately.
NOTE: The F2 prompt indicates that the keyboard has initialized. This prompt
can appear very quickly, so you must watch for it, and then press <F2>. If you
press <F2> before the F2 prompt, this keystroke is lost. If you wait too long and
the operating system logo appears, continue to wait until you see the
operating system’s desktop. Then, turn off your computer and try again.
OM_Book.book Page 76 Tuesday, April 30, 2013 6:07 PM
System Setup | 77
System Setup Screens
The system setup screen displays current or changeable configuration information for
your computer. Information on the screen is divided into three areas: the setup item,
active help screen, and key functions.
System Setup Options
NOTE: Depending on your computer and installed devices, the items listed in this
section may appear, or may not appear exactly as listed.
Setup Item — This field appears on the left
side of the system setup window. This field
is a scrollable list containing features that
define the configuration of your computer,
including installed hardware, power
conservation, and security features.
Scroll up and down the list with the up- and
down-arrow keys. As an option is
highlighted, the Help Screen displays more
information about that option and available
settings.
Help Screen — This field appears on the
right side of the system setup window
and contains information about each
option listed in the Setup Item. In this
field you can view information about
your computer and make changes to
your current settings.
Press the up- and down-arrow keys to
highlight an option. Press <Enter> to
make that selection active and return to
the Setup Item.
NOTE: Not all settings listed in the
Setup Item are changeable.
Key Functions — This field appears below the Help Screen and lists keys and their
functions within the active system setup field.
Main→ System Information
BIOS Revision Display the BIOS revision.
BIOS Build Date Displays the BIOS release date.
System Name Displays the system name.
System Time (hh:mm:ss) Displays the current date.
System Date (mm:dd:yy) Displays the current time.
Service Tag Displays the Service Tag of your computer.
Service Tag Input Allows you to enter the Service Tag of your computer
only if the Service Tag is not present.
Asset Tag Displays the Asset Tag of the computer.
OM_Book.book Page 77 Tuesday, April 30, 2013 6:07 PM
78 | System Setup
Main→ Processor Information
Processor Type Displays the processor type.
Processor ID Displays the processor identification code.
Processor Core Count Displays the number of processor cores in your
computer.
Processor L1 Cache Displays the processor’s total L1 cache size.
Processor L2 Cache Displays the processor’s total L2 cache size.
Processor L3 Cache Displays the processor’s total L3 cache size.
Main→ Memory Information
Memory Installed Displays the total memory (RAM) installed in
your computer.
Memory Available Displays the amount of memory (RAM) available on
your computer.
Memory Running Speed Displays the running speed of the memory (RAM) in
your computer.
Memory Technology Displays the type of memory (RAM) technology used
in your computer.
Main→ SATA Information
SATA 0
Device Type Displays the type of device connected.
Device ID Displays the device identification code.
Device Size Displays the size of the SATA device present in
your computer.
SATA 1
Device Type Displays the type of device connected.
Device ID Displays the device identification code.
Device Size Displays the size of the SATA device present in
your computer.
SATA 2
Device Type Displays the type of device connected.
Device ID Displays the device identification code.
Device Size Displays the size of the SATA device present in
your computer.
OM_Book.book Page 78 Tuesday, April 30, 2013 6:07 PM
System Setup | 79
SATA 3
Device Type Displays the type of device connected.
Device ID Displays the device identification code.
Device Size Displays the size of the SATA device present in
your computer.
mSATA Device
Device Type Displays the type of device connected.
Device ID Displays the device identification code.
Device Size Displays the size of the mSATA device present in
your computer.
Advanced→ Processor Configuration
Intel(R) Hyper-Threading
Technology
If enabled, each physical processor core appears as
two logical processor cores.
Intel(R) SpeedStep
Technology
If enabled, the processor clock speed and core
voltage are adjusted dynamically based on the
processor load.
Intel(R) Virtualization
Technology
If enabled, a Virtual Machine Monitor (VMM) can
access your computer.
CPU XD Support If enabled, allows your computer to use Executive
Display (XD) to hinder software that exploits buffer
overflows.
NOTE: Windows 8 enables this feature even if this
feature is set to disabled.
Limit CPUID Value If enabled, limits the maximum value the processor
CPUID function supports.
Multi Core Support If enabled, allows your computer to use all cores
available in the processor.
Intel(R) Turbo Boost
Technology
If enabled, allows your computer to use turbo boost
when required.
Advanced→ USB Configuration
Front USB Ports Allows you to enable or disable the USB ports at the
front of your computer.
Rear USB Ports Allows you to enable or disable the USB ports at the
back of your computer.
Top USB Ports Allows you to enable or disable the USB ports at the
top of your computer.
OM_Book.book Page 79 Tuesday, April 30, 2013 6:07 PM
80 | System Setup
Advanced→ Onboard Device Configuration
Onboard Audio Controller Allows you to enable or disable the onboard
audio controller.
SATA Mode Allows you to configure the integrated hard drive
controller to ATA or AHCI.
Onboard LAN Controller Allows you to enable or disable the onboard
LAN controller.
Onboard LAN Boot ROM Allows you to enable or disable the ROM of the
onboard LAN controller.
Boot→ Boot Settings Configuration
Numlock Key Select power-on state for numlock.
Keyboard Errors Displays keyboard-related errors during boot.
USB Boot Support Allows you to enable or disable booting from
USB mass-storage devices.
Boot Mode Allows you to select the type of boot.
Secure Boot Control Allows you to enable or disable the secure
boot control.
NOTE: To enable this feature, the computer must be
in the UEFI boot mode and the Load Legacy OPROM
must be set to never.
Secure Boot Mode Allows you to select custom (clear secure boot
database) or standard (fixed secure boot policy)
secure boot mode.
Boot→ Clear Secure Boot Database
Manage All Keys (PK, KEK,
db, dbx)
Displays the keys in the database.
Delete All Keys Allows you to delete all the keys.
Reset All Keys Allows you to reset all the keys.
Load Legacy OPROM Allows you to load the legacy OPROM when in the
UEFI boot mode.
1st Boot Displays the first boot device.
2nd Boot Displays the second boot device.
3rd Boot Displays the third boot device.
4th Boot Displays the fourth boot device.
5th Boot Displays the fifth boot device.
OM_Book.book Page 80 Tuesday, April 30, 2013 6:07 PM
System Setup | 81
Power
Wake Up by Integrated
LAN/WLAN
If enabled, will wake the system using a
network message.
AC Recovery Allows you to select the action the computer takes
when power is restored.
DeepSx Power Policies Allows you to configure the DeepSx mode.
Auto Power On Allows the computer to start up automatically at a
pre-configured time.
Auto Power On Mode Allows you to set the auto power-on mode.
Auto Power On Date Allows you to set the auto power-on date.
Auto Power On Time Allows you to set the auto power-on time.
Intel Smart Connect
Technology
Allows you to disable or enable the Intel Smart
Connect Technology.
Security
Unlock Setup If the supervisor password is set, enter the password
to display the setup options.
Supervisor Password Displays the status of the supervisor password.
User Password Displays the status of the user password.
Set Supervisor Password Allows you to set a supervisor password.
User Access Level Allows you to set the user-access level.
Set User Password Allows you to set a user password.
Password Check Allows you to configure when the computer
prompts for passwords. (When entering system
setup or at every boot.)
Security→ TPM Security
TPM Security Support Allows you to enable or disable the TPM (Trusted
Platform Module) security.
TPM Status Allows you to activate or deactivate the TPM security
support.
Clear TPM If enabled, clears the TPM module settings.
TPM ACPI Support Allows you to enable or disable the
TPM ACPI support.
TPM PPI Provision
Override
Allows you to enable or disable TPM PPI
provision override.
OM_Book.book Page 81 Tuesday, April 30, 2013 6:07 PM
82 | System Setup
Changing Boot Sequence
Changing Boot Sequence for the Current Boot
You can use this feature to change the current boot sequence, for example, to boot from
the optical drive to run Dell Diagnostics from the Drivers and Utilities disc.
The previous boot sequence is restored at the next boot.
1If you are booting from a USB device, connect the USB device to a USB port.
2Turn on (or restart) your computer.
3When F2 Setup, F12 Boot Options appears in the lower-right corner of the
screen, press <F12>.
NOTE: If you wait too long and the operating system logo appears, continue to
wait until you see the operating system’s desktop. Then shut down your
computer and try again.
The Boot Device Menu appears, listing all available boot devices.
4On the Boot Device Menu choose the device you want to boot from.
For example, if you are booting to a USB memory key, highlight
USB Storage Device and press <Enter>.
Changing Boot Sequence for Future Boots
1Enter system setup. See "Entering System Setup" on page 76.
2Use the arrow keys to highlight the Boot menu option and press <Enter> to access
the menu.
NOTE: Write down your current boot sequence in case you want to restore it.
3Press the up- and down-arrow keys to move through the list of devices.
4Press plus (+) or minus (–) to change the boot priority of the device.
TPM PPI Deprovision
Override
Allows you to enable or disable TPM PPI
deprovision override.
Exit
Save Changes and Reset Allows you to save the changes.
Discard Changes and Reset Allows you to discard the changes.
Load Default Allows you to load the default BIOS settings.
OM_Book.book Page 82 Tuesday, April 30, 2013 6:07 PM
System Setup | 83
Clearing Forgotten Passwords
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Locate the password jumper (PSWD) on the system board. See "System-Board
Components" on page 13.
3Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2.
4Wait for approximately five seconds to clear the password setting.
5Remove the 2-pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3.
6Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 83 Tuesday, April 30, 2013 6:07 PM
84 | System Setup
Clearing CMOS Settings
WARNING: Before working inside your computer, read the safety information
that shipped with your computer and follow the steps in "Before You Begin" on
page 9. After working inside your computer, follow the instructions in "After
Working Inside Your Computer" on page 11. For additional safety best practices
information, see the Regulatory Compliance Homepage at
dell.com/regulatory_compliance.
1Remove the computer cover. See "Removing the Computer Cover" on page 15.
2Locate the CMOS jumper (RTCRST) on the system board. See "System-Board
Components" on page 13.
3Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2.
4Wait for approximately five seconds to clear the CMOS setting.
5Remove the 2-pin jumper plug from pins 1 and 2 and replace it on pins 2 and 3.
6Replace the computer cover. See "Replacing the Computer Cover" on page 16.
OM_Book.book Page 84 Tuesday, April 30, 2013 6:07 PM
Flashing the BIOS | 85
Flashing the BIOS
The BIOS may require flashing when an update is available or when replacing the
system board. To flash the BIOS:
1Turn on the computer.
2Go to dell.com/support.
3If you have your computer's Service Tag, type your computer's Service Tag and
click Submit.
If you do not have your computer's Service Tag, click Detect Service Tag to allow
automatic detection of your computer's Service Tag.
NOTE: If the Service Tag cannot be detected automatically, select your
product under the product categories.
4Click Drivers & Downloads.
5In the Operating System drop-down, select the operating system installed on
your computer.
6Click BIOS.
7Click Download File next to the latest version of the BIOS for your computer.
8On the next page, select Single-file download and click Continue.
9Save the file and once the download is complete, navigate to the folder where you
saved the BIOS update file.
10 Double-click the BIOS update file icon and follow the instructions on the screen.
OM_Book.book Page 85 Tuesday, April 30, 2013 6:07 PM
86 | More Information
More Information
To learn about Windows 8:
1Turn on the computer.
2Go to dell.com/support.
3Type Windows 8 in the search box and click Search.
4Click the links to learn about the Windows 8 features.
To learn about your computer features:
1Follow the instructions from step 1 to step 3 in "Flashing the BIOS" on page 85.
2Click Manuals & Documentation tab.
3View or Download the following documents to learn about your
computer features:
•Quick Start Guide: provides information about setting up your computer.
•Specifications: provides information about your computer specifications.
•Me and My Dell: provides information about your computer features.
OM_Book.book Page 86 Tuesday, April 30, 2013 6:07 PM