Table of Contents
DELL C6522QT User Manual
Displayed below is the user manual for C6522QT by DELL which is a product in the Interactive Whiteboards category. This manual has pages.
Related Manuals
Product Announcement:
This product is certificated to meet RoHS
Directive and Lead-Free produced definition.
Using approved critical components only is
recommended when the situation to replace
defective parts. Vender assumes no liability
express or implied, arising out of any unauthorized
modification of design or replacing non-RoHS
parts. Service providers assume all liability.
Qualified Repairability:
Proper service and repair is important to the safe,
reliable operation of all series products. The
service providers recommended by vender should
be aware of notices listed in this service manual in
order to minimize the risk of personal injury when
perform service procedures. Furthermore, the
possible existed improper repairing method may
damage equipment or products. It is recommended
that service engineers should have repairing
knowledge, experience, as well as appropriate
product training per new model before performing
the service procedures.
NOTICE:
! To avoid electrical shocks, the products should be
connected to an authorized power cord, and turn
off the master power switch each time before
removing the AC power cord.
! To prevent the product away from water or
expose in extremely high humility environment.
! To ensure the continued reliability of this
product, use only original manufacturer’s
specified parts.
! To ensure following safety repairing behavior, put
the replaced part on the components side of
PWBA, not solder side.
! To ensure using a proper screwdriver, follow the
torque and force listed in assembly and
disassembly procedures to unscrew screws.
! Using Lead-Free solder to well mounted the
parts.
! The fusion point of Lead-Free solder requested in
the degree of 220°C.
1. Important Safety Notice
2. Exploded view diagram with list of items
3. Wiring Connectivity Diagram
Panel
Driver board
20W speaker 20W speaker
RS232
USB type C with PD 90W
4. Disassembly and Assembly Procedures
4.1 Disassembly Procedures:
Necessary repair and test equipment:
1. Philips-head screwdriver
2. Hex-head screwdriver
3. Air gun and roller
Use a screwdriver to
handles.
Remove 57pcs screws for unlocking the rear cover
with the assembled unit.(
remove 8pcs screws for
releasing the (Torque:15±0.5kgf)
Torque: 3±0.3kgf)
S1
Remove the handles and rear cover, then use a
screwdriver to remove 7pcs screws for releasing the
PC box.(Torque: 4.5±0.3kgf)
S2
Tear off 1pcs conductive tape for releasing main
board, USB board and LVDS cable. Remove 2pcs
white mylar tapes.
Remove 5pcs white tapes, 2pcs big black wire locks,
2pcs small black wire locks and 6pcs white wire locks
for unfixing the cables as the picture below shown.
S3
S4
Disconnect all the cables as the picture below shown.
Use a screwdriver to remove 2pcs screws for
unlocking AC power outlet.(Torque: 4.5±0.5kgf)
S5
Use a screwdriver to remove 4pcs screws for
unlocking the two speakers. (Torque: 4.5kgf±0.5)
S6
Use a Hex-head screwdriver to remove 2pcs screws
for unlocking RS232 connectors. (Torque: 4.5kgf±0.5)
Use a screwdriver to remove 12pcs screws for
unlocking the USB board, IO holder and main board,
remove 17pcs screws for locking the power board,
driver board, touch board and T-Con board. (Torque:
4.5kgf±0.3) Disconnect all the FFC cables away from
the T-con board.
S7
14pcs screws
main board
1
2
3
5
7
6
8
4
6
9
9
10
8
10
11
22
12
13
14
20
21
IR cable
15
18 16 19
17
23
key cable
4. Disassembly and Assembly Procedures
Use a screwdriver to remove 30pcs screws
(left: 5pcs, right :5pcs, top: 10pcs, bottom: 10pcs)
for unlocking 4pcs strips, then tear off 4pcs shading
tape. (Torque: 4.5±0.5kgfkgf)
S11
S8
U
unlocking the key board and the holder with strip.
se a screwdriver to remove 2pcs screws for
(Torque: 2±0.3kgf)
Use a screwdriver to remove 27pcs screws for
unlocking the front bezels(top, left, right, bottom).
(Torque: 3±0.3kgf)
S10
Disconnect the touch connective cable with the
monitor. Use a screwdriver to remove one screw for
locking the grounding wire of the import-export cable,
then disconnect the connective cable from the import
and export cable. (Torque: 3±0.3kgf)
S9
Tear off 8pcs conductive foams on the specific
position of the COF of the SB, then tear off all the
tape and foams, and release the O/C SB away from
the back bracket.
Use a screwdriver to remove 17pcs(11+6) screws
for unlocking the ED holder with
the assembled unit. Tear off 2pcs L/B shading tapes
and 3pcs rubbers.
(Torque:6±0.3kgf)
Remove all the bezel and strips and put them on a
protective cushion. Open the IR board cover, then
use a screwdriver to remove 2pcs screws for
unlocking the IR board and holder with front bezel,
then use a screwdriver to remove 2pcs screws for
unlocking the light pipe with front bezel.
(Torque: 3±0.3kgf)
Use a screwdriver to remove 6pcs screws for
unlocking the two bracket with the bottom ED holder.
(Torque: 3±0.3kgf)
S12
S13
S14
S15
4. Disassembly and Assembly Procedures
Tear off 2pcs shading mylar tape for releasing the
wire hole of the lighter bar. Turn over the panel
module with the bracket for screen faced up. Use a
thin film(such as Prism film) to disassemble the O/C
with glass carefully, then remove the O/C with glass
and put then on a protective cushion.
S16
Use a tripper to lift up the unit, then use a
screwdriver to remove 14pcs screws for unlocking
the ED unit , then use the tripper to put down the
unit. (Torque: 3.5±0.3kgf)
Use a ED holder fixture to fix the ED holders, then
tear off all the tapes and rubbers, then lift up the ED
holder unit for removing the ED unit, and then put
the unit on a protective cushion.
S19
Tear off 8pcs acetate tapes and 2pcs shading foam,
then use a screwdriver to remove 18pcs screws for
unlocking the bottom-middle bezel.
(Torque: 3±0.3kgf)
S20
S21
4. Disassembly and Assembly Procedures
Remove 1pcs DEBF film, 1pcs Diffuser film, 1pcs
LGP, 1pcs Reflector film away from the back
bracket.
S22
Use a screwdriver to remove10pcs screws for
unlocking the two VESA brackets with back
bracket.(Torque: 5±0.5kgf)
Tear off the tape, then disconnect the L/B cable from
the connector, then tear off the L/B from the L/B
heat sink. Use a screwdriver to remove 16pcs
screws for unlocking the L/B heat sink with the back
bracket. (Torque: 5±0.5kgf)
S23
S24
4. Disassembly and Assembly Procedures
Put 1pcs back bracket on the working table, then
take 2pcs VESA brackets to assemble with the back
bracket. Use a screwdriver to tighten 10pcs screws
for locking the two VESA brackets with back bracket.
(Torque: 5±0.3kgf)
Preparation: Take 2pcs light bar and 2pcs double-
faced tape, 1pcs L/B heat sink . Paste 1pcs double-
faced tape on the back of the light bar as the picture
below shown.
4.2 Assembly Procedures:
S1
S2
Assemble
Make sure the gap between light and Reflector
>1.2mm.
1pcs reflector film into the back bracket.
Assemble the L/B heat sink with back bracket.
Use a screwdriver to tighten 16pcs screws for
locking the L/B heat sink with the back bracket.
(Torque: 5±0.5kgf)
S3
S5
Tear off the front film of the LGP, then place 1pcs
Diffuser film on the back bracket, then place 1pcs
DEBF film on the back bracket, and then power on
to check and make sure no particles on the films.
Tear off the papers of double-faced tapes on the L/B,
then paste 2pcs L/B from left to right(1~2) on the
hooks of the L/B heat sink, then use a laminating
fixture to fix the light bar with the heat sink. Connect
2pcs L/B cables to the connectors, then fix the L/B
cables with 2pcs tapes on the back bracket.
S4
S6
Use a sucking tool to suck 1pcs LGP, then tear off
the back protective film of the LGP. Assemble the
LGP with the Reflector and back bracket, then power
on and make sure there is no particles on the film.
S7
4. Disassembly and Assembly Procedures
Paste 2pcs shading foams on the lest and right of
the unit. Take 1pcs bottom-middle bezel to assemble
with the unit, then use a screwdriver to lock bottom-
middle bezel with 18pcs screws. Paste 8pcs Acetate
tape on bottom-middle bezel.(Torque: 3.5±0.3kgf)
Place the Top, left, right and bottom assembled ED
holder units to form a square and then connect them
with the FFC cables, then fix the ED unit with a fixture.
Connect the FFC cable of ED board to the connectors
of the touch board, then connect the power cable and
signal cable to the touch board, then run the special
program and input SN for testing, it stand ok when you
see Pass on the screen.
Disconnect the bottom ED holder away from the left
and right ED holders, then replace the bottom ED
holder with a fixture Jip as the picture below shown.
S8
Take 1pcs bottom-ED-holder and 2pcs small
brackets, then use a screwdriver to tighten 6pcs
screws for locking the two bracket with the bottom
ED holder for later assembling.(Torque: 3±0.3kgf)
S9
Assemble the ED holders unit with the assembled
back bracket, then push the whole unit into a tripper,
then paste 2pcs rubbers on the top side as the
picture below shown.
S10
S11
S12
Note: LS: the board is for Top ED holder; SS: the hold is for left and right ED holder.
S13
Take 1pcs ED Holder, 1pcs ED board, then insert 1st
1pcs ED board into the ED holder as the picture 1.
Connect 2nd ED board with 1st ED board as picture
2. Insert the ED boards into the ED holder as picture
3. Use 1pc Import and export cable to connect right
ED holder and bottom holder as picture 4. Insert 4pcs
ED boards into top ED holder, Insert 2pcs ED boards
into either ED holders(left and right). Use 3pcs cables
to connect ED boards of the top, right, bottom and left
ED holders as picture 5. Paste 3pcs conductive tape
to fix the cables on holders and 8pcs rubbers on the
back of the ED boards.(picture 6~7)
4. Disassembly and Assembly Procedures
Use a sucking tool to suck 1pcs glass and set it on a
jip, then check the glass carefully and make sure no
particles on the glass.
S16
Use a sucking tool to suck the glass and then
assemble the glass with the O/C module, then tear off
all release papers around edges of the O/C module.,
and then press the glass with a roll for two parts firmly
attachment.
S17
Use a sucking tool to suck 1pcs O/C module and
place it on a protective cushion, then supply power
and signal to the O/C module for functionality check,
then disconnect the cables. Paste 4pcs release
tapes around edge of screen of the O/C module,
then tear off the protective film of the O/C module.
S15
Operate the tripper to overturn the unit, then use a
screwdriver to lock 14pcs screws for locking the ED
unit with the back bracket, then turn over the unit for
later assembling.(Torque: 3.5±0.3kgf)
S14
Use a roller to clean the film as the direction of the
arrow. Use a sucking tool to move the O/C with glass
module to assemble with the back bracket. Tear off
the releaser papers of left, right and top ED holders,
and then use a roller to press the O/C with glass
module with the back bracket firmly attached.
S18
4. Disassembly and Assembly Procedures
S21
Use textured tape to fix the SB of the O/C, then turn
over the unit to let the back bracket faced up.
S19
Tear off the textured tape of SB of O/C. Paste 1pcs
long double-faced foam bottom side of the back
bracket. Tear off the release tapes and paste the SB
on the back bracket, then paste 8pcs conductive
foams on COF of SB.
S20
S22
Take 1pcs top front bezel, 1pcs left front bezel, 1pcs
right front bezel, 1pcs bottom front bezel, 4pcs filter
films, 4pcs filter foams(long 2pcs and short 2pcs),
4pcs reflector (long 2pcs and short 2pcs). Paste the
filter foam on the filter film. Paste the reflector and
assembled filter films on the bezel as the picture
below shown.
filter film
Paste 3pcs rubbers on the specific positions of the
back bracket as the picture below shown. Paste
2pcs shading mylar tape to cover the L/B wire holes
as the picture below shown. Assemble 1pcs ED
holder with the assembled unit, and then use a
screwdriver to tighten 20pcs screws for locking the
ED holder with the assembled unit .
(Torque: 6±0.3kgf)
Connect the connective cable with the
export cable. Use a screwdriver to tighten 1pcs screw
for locking the grounding wire of the import-export
cable. Assemble 1pcs touch connective cable with the
monitor.
import and
(Torque: 3±0.3kgf)
S23
4. Disassembly and Assembly Procedures
Paste 1pcs shading foam on the strip of bottom side,
then assemble 1pcs key board holder with the strip as
the picture below shown. Connect 1pcs key cable to
the key board, then locate the key board into the
holder and use a screwdriver to tighten 2pcs screws
for locking the board and the holder with strip.
(Torque: 2±0.3kgf)
Assemble 4pcs front bezels(top, left, right, bottom) with
the assembled unit, then use a screwdriver to tighten
29pcs screws for locking the front bezels with the
assembled unit. (Torque: 3±0.3kgf)
S27
S25
Prepare all the cables, all boards, and all the bezel
and strips, then place all the cables, boards and
bezel on a working tables as the picture below
Left-front bezel
Right-front bezel
Top-front bezel
Bottom-front bezel
top strip
ED unit holder
boards
boards
bottom strip
left strip
right strip
S24
S26
Paste 1pcs foam on the bottom side of the front bezel.
Take 1pcs light pipe, and then use a screwdriver to
lock 2pcs screws for locking the light pipe with front
bezel. Paste 1pcs acetate tape on the bezel, then
assemble 1pcs IR board with IR holder, then use a
screwdriver to lock 2pcs screws for locking the IR
holder with front bezel, then assemble 1pcs IR board
cover to bottom-side of the bezel.(Torque: 3±0.3kgf)
filter film
reflector
foam
acetate tape
left and right bezel
top and bottom bezel
4. Disassembly and Assembly Procedures
Assemble 1pcs power board , 1pcs driver
board , 1pcs 1pcs T-
Con board with back bracket. Take 2pcs FFC
cables to connect the T-con board with SB of
O/C.
(FIG.1)
(FIG.2) (FIG.3)
(FIG.4)
(FIG.6~13)
(Torque: 4.5kgf±0.3)
touch board and
Use a screwdriver to lock 14pcs
screws for locking power board, driver board, touch
board and T-con board.
S29
S30
Take a pair of speakers to assemble with the back
bracket, then use a screwdriver to lock 4pcs screws for
locking speakers with the unit. (Torque: 6kgf±0.5)
main board
S31
S32
Take 1pcs cable to connect driver board with power
board . Take 1pcs cable to
connect the power board with USB board
Take 1pcs cable
Take 1pcs cable to connect the power
board with the USB board Take 1pcs
connective cable to connect USB board with main
board . Take 1pcs IF to Usb FFC to connect
the main board with the Usb board . Connect
the speakers’ cable to the connector of main
board . Connect the touch cable to the
connector of touch board . Connect the L/B
cable to the connector of the driver board .
Take 1pcs AC power outlet and cable to assemble
with the back bracket, then use a screwdriver to lock
2pcs screws for locking the AC outlet and grounding
wire, then plug the other end of cable to the power
board. Take 1pcs cable (
connect touch board with main board
, take 1pcs cable( connect
touch board with USB board . Take 1pcs
LVDS cable to connect main board with T-con
board
(FIG.1~2)
(FIG. 3~4)
(FIG.7~8)
(FIG.9)
(FIG.10)
(FIG.11)
(FIG.12)
(FIG.13)
(FIG.14)
(FIG.15~17)
(FIG.18~19)
(FIG.20~21).
(FIG.22)
(FIG.23)
(2 connectors)
(3 connectors)
(FIG.5~6)
(2 connectors)
(Torque:4.5kgf±0.5) 3
connectors)
2 connectors)
.
to connect the power
board with main board and USB board .
.
Connect 1pcs IR cable to connect
the main board. Connect the function key
cable to the connector of the main board.
Paste 4pcs shading tape. Assemble 4pcs strips(top,
left, right, bottom) with the assembled unit. Use a
screwdriver to tighten 31pcs (left: 5pcs, right :5pcs, top:
10pcs, bottom: 11pcs) screws for locking the 4pcs strip
with the assembled unit.(Torque: 4.5±0.5kgf)
S28
Use a screwdriver to lock 4pcs screws to the back
bracket, then
for locking 1pcs main board with the screws, and then
assemble 1pcs USB board and 1pcs IO holder with
the main board, then lock 4pcs screws for locking the
USB board, lock 2pcs hex screws for locking the
RS232 connector.
use a screwdriver to lock 4pcs screws
(Torque:4.5kgf±0.5)
1
2
3
5
7
6
8
4
6
9
9
10
8
10
11
22 12
13
14
21
IR cable
15
18 16 19
17
23
key cable
20
4. Disassembly and Assembly Procedures
Paste 1pcs conductive tape to cover main board and
USB board. Paste 2pcs white mylar tape on the
specific position as the picture below shown.
Take 1pcs rear cover, assemble the rear cover with
the assembled unit, then use a screwdriver to lock
the rear cover with 60pcs screws.
Assemble 4pcs handles with the rear cover, then
lock the handles with 16pcs screws.
(Torque: 3±0.3kgf)
(Torque:15±0.5kgf)
Use a texture to paste 1psc cable lock on the
specific position of the rear cover.
Use a clean cloth to wipe the screen of the monitor,
then check the monitor following the inspection spec,
and wipe the screen with a clean cloth again after
checking.
S37
S36
S34
Place 1pcs PC box to the specific positions of the
whole unit, then use a screwdriver to lock 7pcs screws
for fixing the PC box. (Torque: 4.5±0.3kgf)
S35
Paste 1pcs LCM SN label on the back bracket as the
picture below shown. Use 2pcs big black, 2pcs small
black and 7pcs white wire locks to fix the cables and
then paste them on the back bracket. Paste 5pcs
white tapes to fix the cables as the picture below
shown.
S33
5. Trouble Shooting Instructions
Self-Test
Your display provides a self-test feature that allows you to check whether your display
is functioning properly. If your display and computer are properly connected but the
display screen remains dark, run the display self-test by performing the following steps:
1. Turn o both your computer and the display.
2.
Unplug the video cable from the back of the computer. To ensure proper Self-Test
operation, remove all digital and the analog cables from the back of computer.
3. Turn on the display.
The floating dialog box should appear on-screen (against a black background), if the
display cannot sense a video signal and is working correctly. While in self-test mode,
the power LED remains white. Also, depending upon the selected input, one of the
dialogs shown below will continuously scroll through the screen.
Dell 65 Monitor
No HDMI 1 Cable
The display will go into Standby Mode in 4 minutes.
www.dell.com/C6522QT
C6522QT
or
Dell 65 Monitor
No HDMI 2 Cable
The display will go into Standby Mode in 4 minutes.
www.dell.com/C6522QT
C6522QT
or
Dell 65 Monitor
No HDMI 3 Cable
The display will go into Standby Mode in 4 minutes.
www.dell.com/C6522QT
C6522QT
or
Dell 65 Monitor
No DP Cable
www.dell.com/C6522QT
C6522QT
The display will go into Standby Mode in 4 minutes.
5. Trouble Shooting Instructions
or
Dell 65 Monitor
No USB Type-C Cable
www.dell.com/C6522QT
C6522QT
The display will go into Standby Mode in 4 minutes.
4. This box also appears during normal system operation, if the video cable becomes
disconnected or damaged.
5. Turn o your display and reconnect the video cable; then turn on both your
computer and the display.
If your display screen remains blank after you use the previous procedure, check your
video controller and computer, because your display is functioning properly.
Built-in diagnostics
Your display has a built-in diagnostic tool that helps you determine if the screen
abnormality you are experiencing is an inherent problem with your display, or with your
computer and video card.
1 2 3 4 5 6 7
To run the built-in diagnostics:
1. Make sure that the screen is clean (no dust particles on the surface of the
screen).
2. Touch and hold for 5 seconds in lock Select Option. Touch the self-inspection
icon A gray screen appears.
3. Carefully inspect the screen for abnormalities.
4. Touch the front panel. The color of the screen changes to red.
5. Inspect the display for any abnormalities.
6. Repeat steps 4 and 5 to inspect the display in green, blue, black, white, and text
screens.
The test is complete when the text screen appears. To exit, touch panel again.
If you do not detect any screen abnormalities upon using the built-in diagnostic tool,
the display is functioning properly. Check the video card and computer.
5. Trouble Shooting Instructions
Common problems
The following table contains general information about common display problems you
might encounter and the possible solutions:
Common
Symptoms
What You
Experience
Possible Solutions
No Video/
Power LED off
No picture • Ensure that the video cable connecting the
display and the computer is properly connected
and secure.
• Verify that the power outlet is functioning
properly using any other electrical equipment.
• Ensure that the power button is depressed
fully.
• Ensure that the correct input source is selected
in the Input Source menu.
No Video/
Power LED on
No picture or no
brightness
• Increase brightness & contrast controls via
OSD.
• Perform display self-test feature check.
• Check for bent or broken pins in the video
cable connector.
• Run the built-in diagnostics.
• Ensure that the correct input source is selected
in the Input Source menu.
Poor Focus Picture is
fuzzy, blurry, or
ghosting
• Eliminate video extension cables.
• Reset the display to factory settings.
• Change the video resolution to the correct
aspect ratio.
Shaky/Jittery
Video
Wavy picture or
fine movement
• Reset the display to factory settings.
• Check environmental factors.
• Relocate the display and test in another room.
Missing Pixels LCD screen has
spots
• Cycle power on-o.
• Pixel that is permanently o is a natural defect
that can occur in LCD technology.
• For more information on Dell Display Quality
and Pixel Policy, see Dell Support site at:
http://www.dell.com/support/monitors.
Stuck-on Pixels LCD screen has
bright spots
• Cycle power On-O.
• Pixel that is permanently o is a natural defect
that can occur in LCD technology.
• For more information on Dell Display Quality
and PixelPolicy, see Dell Support site at:
http://www.dell.com/support/monitors.
Brightness
Problems
Picture too dim
or too bright
• Reset the display to factory settings.
• Adjust brightness & contrast controls via OSD.
5. Trouble Shooting Instructions
Common
Symptoms
What You
Experience
Possible Solutions
Audio problem No Audio • Check PC setting if the playback is correctly
selected.
• Checking other video cables.
• Ensure that the Speaker is enabled via OSD
Geometric
Distortion
Screen not
centered
correctly
• Reset the display to factory settings.
Synchronization
Problems
Screen is
scrambled or
appears torn
• Reset the display to factory settings.
• Perform display self-test feature check to
determine if the scrambled screen appears in
self-test mode.
• Check for bent or broken pins in the video
cable connector.
• Restart the computer in safe mode.
Safety Related
Issues
Visible signs of
smoke or sparks
• Do not perform any troubleshooting steps.
• Contact Dell immediately.
Intermittent
Problems
Display
malfunctions on
& off
• Ensure that the video cable connecting the
display to the computer is connected properly
and is secure.
• Reset the display to factory settings.
• Perform display self-test feature check to
determine if the intermittent problem occurs in
self-test mode.
Missing Color Picture missing
color
• Perform display self-test.
• Ensure that the video cable connecting the
display to the computer is connected properly
and is secure.
• Check for bent or broken pins in the video
cable connector.
Wrong Color Picture color
not good
• Change the settings of the Preset Modes
in the Color menu OSD depending on the
application.
• Adjust R/G/B value under Custom. Color in
Color menu OSD.
• Change the Input Color Format to PC RGB or
YCbCr in the Color menu OSD.
• Run the built-in diagnostics.
Image retention
from a static
image left on
the display for
a long period of
time
Faint shadow
from the static
image displayed
appears on the
screen
• Set the screen to turn o after a few minutes
of screen idle time. These can be adjusted in
Windows Power Options or Mac Energy Saver
setting.
• Alternatively, use a dynamically changing
screensaver.
Touchscreen
non-responsive
Display cannot
wake on touch
• Ensure Wake On Touch is enabled via OSD.
Wake On Touch is default o.
5. Trouble Shooting Instructions
Product specific problems
Specific
Symptoms
What You
Experience
Possible Solutions
Screen image is
too small
Image is
centered on
screen, but
does not fill
entire viewing
area
• Check the Aspect Ratio setting in the Display
menu OSD.
• Reset the display to factory settings.
Cannot adjust
the display with
touch OSD
OSD does not
appear on the
screen
• Turn o the display, unplug the display power
cable, plug it back, and then turn on the display.
• Check whether the OSD menu is locked. If yes,
touch icon for 4 seconds to unlock .
No Input Signal
when user
controls are
pressed
No picture, the
LED light is
white
• Check the signal source. Ensure the computer
is not in the power saving mode by moving the
mouse or pressing any key on the keyboard.
• Check whether the signal cable is plugged in
properly. Re-plug the signal cable if necessary.
• Reset the computer or video player.
The picture
does not fill the
entire screen
The picture
cannot fill the
height or width
of the screen
• Due to dierent video formats (aspect ratio) of
DVDs, the display may display in full screen.
• Run the built-in diagnostics.
No image
when using
USB Type-C
connection
to computer,
laptop, and so
on
Black screen • Verify if the USB Type-C interface of the
device can support DP alternate mode.
• Verify if the device required more than 90 W
power charging.
• USB Type-C interface of device cannot support
DP alternate mode.
• Set Windows to Projection mode.
• Ensure that the USB Type-C cable is not
damaged.
No charging
when using
USB Type-C
connection
to computer,
laptop, and so
on
No charging • Verify if the device can support one of 5 V/9
V/15 V/20 V charging proles.
• Verify if the Notebook requires a >90 W power
adaptor.
• If the Notebook requires a >90 W power
adaptor, it may not charge with the USB
Type-C connection.
• Ensure that you use only Dell approved adapter
or the adapter that comes with the product.
• Ensure that the USB Type-C cable is not
damaged.
5. Trouble Shooting Instructions
Specific
Symptoms
What You
Experience
Possible Solutions
Intermittent
charging
when using
USB Type-C
connection to
computer,
laptop, and so
on
Intermittent
charging
• Check if the maximum power consumption of
device is over 90 W.
• Ensure that you use only Dell approved adapter
or the adapter that comes with the product.
• Ensure that the USB Type-C cable is not
damaged.
Touchscreen problems
Specific
Symptoms
What You
Experience
Possible Solutions
Touch report
error
Touch function
miss alignment
or no touch
function
• Use the Dell provided USB cable to connect
your computer.
• Make sure the power cable has a ground pin.
• Unplug and replug the power cable to allow
initialization of the touch module.
• Make sure computer supports USB 2.0 or later.
• If the display cannot be detected by the
computer, power o/on the monitor or unplug
and replug the USB cable.
Touchscreen
non-responsive
in standby
mode
Cannot wake
up display and
computer by
using touch in
standby mode
• Access Device Manager, expand HID Interface
Device under Human Device.
• Right click HID- compliant device, click
Properties and select the check-box to allow
the device to wake the computer.
• Check Display OSD ‘Wake on touch’ setting is
enabled.
5. Trouble Shooting Instructions
Universal Serial Bus (USB) specific problems
Specific
Symptoms
What You
Experience
Possible Solutions
USB interface is
not working
USB peripherals
are not working
• Check that your display is turned ON.
• Reconnect the upstream cable to your
computer.
• Reconnect the USB peripherals (downstream
connector).
• Switch o and then turn on the display again.
• Reboot the computer.
• Some USB devices like external portable HDD
require higher electric current; connect the
device directly to the computer system.
SuperSpeed
USB 3.1
interface is
slow.
SuperSpeed
USB 3.1
peripherals
working slowly
or not working
at all
• Check that your computer is USB 3.1-capable.
• Some computers have USB 3.1, USB 3.0, USB
2.0, and USB 1.1 ports. Ensure that the correct
USB port is used.
• Reconnect the upstream cable to your
computer.
• Reconnect the USB peripherals (downstream
connector).
• Reboot the computer.
Wireless USB
peripherals stop
working when a
USB 3.1 device
is plugged in
Wireless USB
peripherals
responding
slowly or only
working as
the distance
between itself
and its receiver
decreases
• Increase the distance between the USB 3.1
peripherals and the wireless USB receiver.
• Position your wireless USB receiver as close as
possible to the wireless USB peripherals.
• Use a USB-extender cable to position the
wireless USB receiver as far away as possible
from the USB 3.1 port.
USB is not
working
No USB
functionalities
• Refer to input source and USB pairing table.
5. Trouble Shooting Instructions
Ethernet problems
Specific
Symptoms
What You
Experience
Possible Solutions
Ethernet not
working
Dell Web
Management
for Displays
Webpage
control is not
working
• Ensure that the Network cable connecting the
Display is properly secured.
• Touch the icon 5 on the screen for 4 seconds
to turn on , A network icon appears and is
shown on the center for 4 seconds .
• Touch the icon 5 on the front panel for 4
seconds to turn o, A network icon appears
and is shown on the center for 4 seconds.
1 2 3 4 5 6 7