DELL E2722HS User Manual
Displayed below is the user manual for E2722HS by DELL which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
27" LED Monitor Dell E2722HS
Service
Service
Service
Simplified
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all DELL Company Equipment. The service
procedures recommended by DELL and described in this service manual are effective methods of performing
service operations. Some of these service operations require the use of tools specially designed for the purpose.
The special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read
in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. DELL could not possibly know, evaluate and advise the service trade of all conceivable ways
in which service might be done or of the possible hazardous consequences of each way. Consequently, DELL has
not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is
not recommended by DELL must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, DELL Company will be referred to as DELL.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create
shock, fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from DELL.
DELL assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION
OF THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth
may damage the panel.)
1. Exploded view diagram with list of items
2. Wiring connectivity diagram
3. Tools Required
List the type and size of the tools that would typically can be used to disassemble the product to a point
where components and materials requiring selective treatment can be removed.
Tool Description:
‐ Screwdriver (Phillip-head, Hexagonal head)
‐ Penknife
3.1Disassembly Procedures
Tools: 2 Power screwdrivers (φ=5mm, L=60mm); 1 small cross screwdriver; turnbuckle driver;
Setting: Power screwdriver torque A=6 kgF.Cm
Step
Figure
TOOl
Remark
Remove the
Base ass’y.
Unscrew the screw
loosely by hand and
pull out the stand.
Note:
Put the monitor on a
flat, soft and clean
surface.
.
Unscrew the 4
screws by the
Philips-head
Screwdriver and
insert the scraper
into the button site
to open the rear
cover
Remove the
Rear cover
Disconnect
speaker cables
Remove the
mainframe
Remove all the
aluminum foil and
the cable
connectors and
Unscrew the two
screws on the two
sites of mainframe
remove the mylar on
the powerboard
Remove the
mainboard
and power
board
Unscrew the screws
on the boards
Unscrew the two
Hexagonal screws
Mainboard
and
powerboard
3.2 Assembly Procedures:
panel
Assemble
the boards
screw the screws on
the mainboard and
powerboard
Assemble
the maylar
4. Trouble shooting instructions
Assemble
the rear
cover
screw the six screws
by the Philips-head
Screwdriver
Assemble
the stand
ass’y
Tighten the screw
on the stand ass’y
