DELL E3470 User Manual

Displayed below is the user manual for E3470 by DELL which is a product in the Notebooks category. This manual has pages.

Related Manuals

Origin Storage DELL-BDRW-SATA Manual

DELL R820 Manual

DELL P2414H Manual

DELL 1815dn Manual

DELL R7610 Manual

DELL E7240 Manual

DELL 3440 Manual

Dell Latitude 3470

Owner's Manual

Regulatory Model: P63G

Regulatory Type: P63G001

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you

how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

intellectual property laws. Dell™ and the Dell logo are trademarks of Dell Inc. in the United States and/or other

jurisdictions. All other marks and names mentioned herein may be trademarks of their respective companies.

2016 - 01

Rev. A00

Contents

1 Working on your computer.................................................................................6

Safety instructions................................................................................................................................. 6

Before working inside your computer..................................................................................................7

Turning off your computer................................................................................................................... 7

After working inside your computer.....................................................................................................8

2 Removing and installing components..............................................................9

Recommended tools.............................................................................................................................9

Removing the battery............................................................................................................................9

Installing the battery..............................................................................................................................9

Removing the base cover................................................................................................................... 10

Installing the base cover..................................................................................................................... 10

Removing the keyboard......................................................................................................................10

Installing the keyboard.........................................................................................................................11

Removing the hard drive assembly..................................................................................................... 11

Installing the hard drive assembly.......................................................................................................12

Removing the hard drive bracket........................................................................................................12

Installing the hard drive bracket..........................................................................................................12

Removing the WLAN card................................................................................................................... 13

Installing the WLAN card..................................................................................................................... 13

Removing the memory module..........................................................................................................13

Installing the memory module............................................................................................................14

Removing the palmrest....................................................................................................................... 14

Installing the palmrest......................................................................................................................... 15

Removing the coin cell battery...........................................................................................................15

Installing the coin cell battery.............................................................................................................16

Removing the USB board....................................................................................................................16

Installing the USB board...................................................................................................................... 17

Removing the VGA board....................................................................................................................17

Installing the VGA board......................................................................................................................17

Removing the speakers.......................................................................................................................18

Installing the speakers.........................................................................................................................18

Removing the system fan....................................................................................................................19

Installing the system fan......................................................................................................................19

Removing the display cable................................................................................................................20

Installing the display cable..................................................................................................................20

Removing the power connector port................................................................................................ 20

Installing the power connector port...................................................................................................21

Removing the system board............................................................................................................... 21

Installing the system board.................................................................................................................22

Removing the heat sink.......................................................................................................................22

Installing the heat sink.........................................................................................................................23

Removing the display assembly......................................................................................................... 24

Installing the display assembly........................................................................................................... 24

Removing the display bezel................................................................................................................25

Installing the display bezel..................................................................................................................26

Removing the camera.........................................................................................................................26

Installing the camera...........................................................................................................................27

Removing the display panel................................................................................................................27

Installing the display panel..................................................................................................................28

3 System Setup....................................................................................................... 29

Boot Sequence....................................................................................................................................29

Navigation keys................................................................................................................................... 29

System Setup overview.......................................................................................................................30

Accessing System Setup..................................................................................................................... 30

General screen options....................................................................................................................... 31

System Configuration screen options................................................................................................ 31

Video screen options.......................................................................................................................... 33

Security screen options.......................................................................................................................33

Secure Boot screen options............................................................................................................... 35

Performance screen options.............................................................................................................. 36

Power Management screen options.................................................................................................. 36

POST Behavior screen options...........................................................................................................38

Virtualization support screen options................................................................................................ 39

Wireless screen options......................................................................................................................39

Maintenance screen options.............................................................................................................. 39

System Log screen options................................................................................................................ 40

Updating the BIOS ............................................................................................................................. 40

System and setup password...............................................................................................................40

Assigning a system password and setup password......................................................................41

Deleting or changing an existing system and/or setup password.............................................. 41

4 Diagnostics.......................................................................................................... 43

Enhanced Pre-Boot System Assessment (ePSA) diagnostics............................................................43

Device status lights............................................................................................................................. 44

Battery status lights.............................................................................................................................44

5 Technical specifications....................................................................................45

System specifications..........................................................................................................................45

Processor specifications..................................................................................................................... 45

Memory specifications........................................................................................................................45

Audio specifications............................................................................................................................46

Video specifications............................................................................................................................46

Camera specifications........................................................................................................................ 46

Communication specifications.......................................................................................................... 46

Port and connector specifications..................................................................................................... 47

Display specifications..........................................................................................................................47

Keyboard specifications......................................................................................................................48

Touchpad specifications.....................................................................................................................48

Battery specifications..........................................................................................................................48

AC Adapter specifications...................................................................................................................49

Physical specifications........................................................................................................................ 49

Environmental specifications............................................................................................................. 50

6 Contacting Dell................................................................................................... 51

Working on your computer

Safety instructions

Use the following safety guidelines to help protect your computer from potential damage and to help to

ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes

that the following conditions exist:

• You have read the safety information that shipped with your computer.

• A component can be replaced or--if purchased separately--installed by performing the removal

procedure in reverse order.

WARNING: Disconnect all power sources before opening the computer cover or panels. After you

finish working inside the computer, replace all covers, panels, and screws before connecting to

the power source.

WARNING: Before working inside your computer, read the safety information that shipped with

your computer. For additional safety best practices information, see the Regulatory Compliance

Homepage at www.dell.com/regulatory_compliance

CAUTION: Many repairs may only be done by a certified service technician. You should only

perform troubleshooting and simple repairs as authorized in your product documentation, or as

directed by the online or telephone service and support team. Damage due to servicing that is

not authorized by Dell is not covered by your warranty. Read and follow the safety instructions

that came with the product.

CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or

by periodically touching an unpainted metal surface, such as a connector on the back of the

computer.

CAUTION: Handle components and cards with care. Do not touch the components or contacts

on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a

processor by its edges, not by its pins.

CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable

itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,

press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep

them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,

ensure that both connectors are correctly oriented and aligned.

NOTE: The color of your computer and certain components may appear differently than shown in

this document.

Before working inside your computer

To avoid damaging your computer, perform the following steps before you begin working inside the

computer.

1. Ensure that you follow the Safety instructions.

2. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.

3. Turn off your computer, see Turning off your computer.

CAUTION: To disconnect a network cable, first unplug the cable from your computer and

then unplug the cable from the network device.

4. Disconnect all the network cables from the computer.

5. Disconnect your computer and all attached devices from the electrical outlets.

6. Press and hold the power button while the computer is unplugged to ground the system board.

7. Remove the cover.

CAUTION: Before touching anything inside your computer, ground yourself by touching an

unpainted metal surface, such as the metal at the back of the computer. While you work,

periodically touch an unpainted metal surface to dissipate static electricity, which could

harm internal components.

Turning off your computer

CAUTION: To avoid losing data, save and close all open files and exit all open programs before

you turn off your computer.

1. Turning off your computer:

• In Windows 10 (using a touch enabled device or mouse):

1. Click or tap .

2. Click or tap and then click or touch Shut down.

• In Windows 8 (using a touch enabled device):

1. Swipe in from the right edge of the screen, opening the Charms menu and select Settings.

2. Tap and then tap Shut down

• In Windows 8 (using a mouse):

1. Point to upper-right corner of the screen and click Settings.

2. Click and then click Shut down.

• In Windows 7:

1. Click Start.

2. Click Shut Down.

2. Ensure that the computer and all attached devices are turned off. If your computer and attached

devices did not automatically turn off when you shut down your operating system, press and hold

the power button for about 6 seconds to turn them off.

After working inside your computer

After you complete any replacement procedure, ensure you connect any external devices, cards, and

cables before turning on your computer.

CAUTION: To avoid damage to the computer, use only the battery designed for this particular

Dell computer. Do not use batteries designed for other Dell computers.

1. Connect any external devices, such as a port replicator or media base, and replace any cards, such as

an ExpressCard.

2. Connect any telephone or network cables to your computer.

CAUTION: To connect a network cable, first plug the cable into the network device and then

plug it into the computer.

3. Replace the battery.

4. Replace the base cover.

5. Connect your computer and all attached devices to their electrical outlets.

6. Turn on your computer.

Removing and installing components

This section provides detailed information on how to remove or install the components from your

computer.

Recommended tools

The procedures in this document require the following tools:

• Small flat blade screwdriver

• Phillips #0 screwdriver

• Phillips #1 screwdriver

• Small plastic scribe

Removing the battery

1. Follow the procedure in Before Working Inside Your Computer.

2. To remove the battery:

a. Slide the battery latch to release the battery [1].

b. Pull and lift the battery to remove it from the computer [2].

Installing the battery

1. Insert the battery into the slot until it clicks in place.

2. Follow the procedure in After Working Inside Your computer.

Removing the base cover

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the battery.

3. To remove the base cover:

a. Loosen the captive screws that secure the base cover to the computer [1].

b. Using a plastic scribe, pry the base cover and remove it from the computer [2].

Installing the base cover

1. Replace the base cover on the computer until it clicks in place.

2. Tighten the captive screws to secure the base cover to the computer.

3. Install the battery.

4. Follow the procedure in After Working Inside Your computer.

Removing the keyboard

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the battery.

3. Flip the computer and open the display to access the keyboard.

4. To remove the keyboard:

a. Using a plastic scribe, release the keyboard from the edges [1] and lift the keyboard from the

computer [2].

b. Release the latch and disconnect the keyboard cables from the connectors on the system board

[3, 4].

Installing the keyboard

1. Connect the keyboard cables to the connectors on the system board.

2. Place the keyboard on the computer and press along all the sides until it clicks in place.

3. Install the battery.

4. Follow the procedure in After Working Inside Your computer.

Removing the hard drive assembly

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

3. To remove the hard drive assembly:

a. Remove the screws that secure the hard drive assembly to the computer [1].

b. Disconnect the hard drive assembly cable from the connector on the system board [2].

c. Lift and remove the hard drive assembly from the computer [3].

Installing the hard drive assembly

1. Replace the hard drive assembly into the slot on the computer.

2. Connect the hard drive assembly cable to the connector on the system board.

3. Tighten the screws to secure the hard drive assembly to the computer.

4. Install the:

a. battery

b. base cover

5. Follow the procedure in After Working Inside Your computer.

Removing the hard drive bracket

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

3. To remove the hard drive bracket:

a. Remove the screws to release the hard drive bracket from the hard drive assembly [1].

b. Remove the hard drive from the hard drive bracket [2].

c. Disconnect the hard drive cable from the hard drive [3].

Installing the hard drive bracket

1. Connect the hard drive cable to the connector on the hard drive.

2. Place the hard drive brackets on the hard drive to align the screw holders on both sides of the hard

drive.

3. Tighten the screws to secure the hard drive bracket to the hard drive.

4. Install the:

a. hard drive assembly

b. base cover

c. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the WLAN card

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

3. To remove the WLAN card:

a. Loosen the captive screw [1] to remove the metal tab from the WLAN card [2].

b. Disconnect the WLAN cables from the WLAN card [3].

c. Using a plastic scribe, release the WLAN card from the computer [4].

d. Disconnect the WLAN card from the connector to remove it [5].

Installing the WLAN card

1. Connect the WLAN card to the connector on the system board.

2. Connect the WLAN antenna cables to the connectors on the WLAN card.

3. Place the metal tab to align it with the screw holder on the WLAN card to secure the WLAN cables.

4. Tighten the captive screw to secure the WLAN card to the computer.

5. Install:

a. base cover

b. battery

6. Follow the procedure in After Working Inside Your computer.

Removing the memory module

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

3. To remove the memory module:

a. Release the retention clips away from the memory module until the memory module pops up [1].

b. Disconnect the memory module from the connector to remove it from the computer [2].

Installing the memory module

1. Insert the memory module into the connector and press until the memory module clicks into the

place.

2. Install the:

a. base cover

b. battery

3. Follow the procedure in After Working Inside Your computer.

Removing the palmrest

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

3. Remove the screws that secure the palmrest to the computer.

4. To remove the palmrest:

a. Release the latch and disconnect the power button, finger print reader, touchpad, and LED cables

from the connectors on the system board [1, 2].

b. Remove the screws that secure the palmrest to the computer [3].

c. Using a plastic scribe, release the palmrest from the edges and remove it from the computer [4].

Installing the palmrest

1. Place the palmrest on the computer and press along all the sides until it clicks in place.

2. Connect the power button, finger print reader, touchpad, and LED cables to the connectors on the

system board.

3. Flip the computer and tighten the screws to secure the palmrest to the computer.

4. Install the:

a. keyboard

b. hard drive assembly

c. base cover

d. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the coin cell battery

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

f. system board

3. To remove the coin cell battery:

a. Disconnect the coin cell battery cable from the connector on the system board.

b. Lift and remove the coin cell battery from the adhesive on the system board.

Installing the coin cell battery

1. Replace the coin cell battery in the slot on the system board.

2. Connect the coin cell battery to the connector on the system board.

3. Install the:

a. system board

b. palmrest

c. keyboard

d. hard drive assembly

e. base cover

f. battery

4. Follow the procedure in After Working Inside Your computer.

Removing the USB board

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

3. To remove the USB board:

a. Lift the latch and disconnect the USB board cable from the connector on the USB board [1, 2].

b. Remove the screw that secures the USB board to the computer [3].

c. Lift and remove the USB board from the computer [4].

Installing the USB board

1. Place the USB board into the slot on the computer.

2. Tighten the screw to secure the USB board to the computer.

3. Connect the USB board cable to the connector on the USB board.

4. Install the:

a. palmrest

b. keyboard

c. hard drive assembly

d. base cover

e. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the VGA board

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

3. To remove the VGA board:

a. Peel the adhesive tape to access the VGA board cable [1].

b. Lift the latch and disconnect the VGA board cable from the connector on the VGA board [2, 3].

c. Remove the screw that secures the VGA board to the computer.

d. Lift and remove the VGA board from the computer [4].

Installing the VGA board

1. Place the VGA board into the slot on the computer.

2. Tighten the screw to secure the VGA board to the computer.

3. Connect the VGA board cable to the connector on the VGA board.

4. Fix the adhesive tape to secure the VGA board cable.

5. Install the:

a. palmrest

b. keyboard

c. hard drive assembly

d. base cover

e. battery

6. Follow the procedure in After Working Inside Your computer.

Removing the speakers

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

3. To remove the speakers:

a. Disconnect the speaker cable from the connector on the system board [1].

b. Lift and remove the left speaker from the computer [2].

c. Release the speaker cable from the routing channels.

d. Lift and remove the right speaker from the computer [2].

Installing the speakers

1. Place the speakers on both slots on the computer.

2. Route the speaker cable to align it through the routing channels.

3. Connect the speaker cable to the connector on the system board.

4. Install the:

a. palmrest

b. keyboard

c. hard drive assembly

d. base cover

e. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the system fan

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

3. To remove the system fan:

a. Disconnect the system fan cable from the connector on the system board [1].

b. Remove the screws that secure the system fan to the computer [2].

c. Lift and remove the system fan from the computer [3].

Installing the system fan

1. Place the system fan into the slot on the computer.

2. Tighten the screws to secure the system fan to the computer.

3. Connect the system fan cable to the connector on the system board.

4. Install the:

a. palmrest

b. keyboard

c. hard drive assembly

d. base cover

e. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the display cable

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

3. To remove the display cable:

a. Remove the screw to release the metal tab that secures the display cable [1].

b. Lift the metal tab to access the display cable [2].

c. Peel the adhesive tape that secures the display cable [3].

d. Disconnect the display cable from the connector on the system board [4].

Installing the display cable

1. Connect the display cable to the connector on the system board.

2. Affix the adhesive tape to secure the display cable.

3. Place the metal tab on the display cable.

4. Tighten the screw to secure the metal tab.

5. Install the:

a. palmrest

b. keyboard

c. hard drive assembly

d. base cover

e. battery

6. Follow the procedure in After Working Inside Your computer.

Removing the power connector port

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. keyboard

e. palmrest

f. display cable

3. To remove the power connector port:

a. Disconnect the power connector port cable from the connector on the system board [1].

b. Release the power connector port cable from the placeholders.

c. Remove the screw that secures that power connector port to the computer [2].

d. Lift and remove the power connector port from the computer [3].

Installing the power connector port

1. Insert the power connector port into the slot on the computer.

2. Route the power connector port cable through the routing channels.

3. Connect the power connector port cable to the connector on the system board.

4. Tighten the screw to secure the power connector port to the computer.

5. Install the:

a. display cable

b. palmrest

c. keyboard

d. hard drive assembly

e. base cover

f. battery

6. Follow the procedure in After Working Inside Your computer.

Removing the system board

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. WLAN card

e. memory

f. keyboard

g. palmrest

h. display cable

i. system fan

3. To remove the system board:

a. Disconnect all the cables from the connectors on the system board.

b. Remove the screw that secures the system board to the computer [1].

c. Lift and remove the system board from the computer [2].

Installing the system board

1. Place the system board into the slot on the computer.

2. Connect all the cables to the connectors on the system board

3. Tighten the screw to secure the system board to the computer.

4. Install the:

a. system fan

b. display cable

c. palmrest

d. keyboard

e. memory

f. WLAN card

g. hard drive assembly

h. base cover

i. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the heat sink

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. WLAN card

e. memory

f. keyboard

g. palmrest

h. display cable

i. system fan

j. system board

3. To remove the heat sink:

a. Remove the screws that secure the heat sink to the system board [1, 2, 3].

b. Lift and remove the heat sink from the computer [4].

Installing the heat sink

1. Place the heat sink to align with the screw holders on the system board.

2. Tighten the screws to secure the heat sink to the system board.

3. Install the:

a. system board

b. system fan

c. display cable

d. palmrest

e. keyboard

f. memory

g. WLAN card

h. hard drive assembly

i. base cover

j. battery

4. Follow the procedure in After Working Inside Your computer.

Removing the display assembly

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. WLAN card

e. memory

f. keyboard

g. palmrest

h. display cable

i. power connector port

j. system fan

k. system board

3. To remove the display assembly:

a. Remove the rubber on both sides of the computer [1].

b. Remove the screws that secure the display assembly to the chassis [2].

c. Lift and remove the display assembly from the chassis [3].

Installing the display assembly

1. Place the display assembly to align with the screw holders on the chassis.

2. Place the rubber on both sides of the computer.

3. Tighten the screws to secure the display assembly to the chassis.

4. Install the:

a. system board

b. system fan

c. display cable

d. power connector port

e. palmrest

f. keyboard

g. memory

h. WLAN card

i. hard drive assembly

j. base cover

k. battery

5. Follow the procedure in After Working Inside Your computer.

Removing the display bezel

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. WLAN card

e. memory

f. keyboard

g. palmrest

h. display cable

i. system fan

j. system board

k. power connector port

l. display assembly

3. To remove the display bezel:

a. Using a plastic scribe, release the display bezel from the bottom of the display assembly [1].

b. Release the display bezel from its edges and remove the display bezel from the display assembly

[2, 3, 4].

Installing the display bezel

1. Place the display bezel on the computer and press along all the sides until it clicks in place.

2. Install the:

a. display assembly

b. power connector port

c. system board

d. system fan

e. display cable

f. palmrest

g. keyboard

h. memory

i. WLAN card

j. hard drive assembly

k. base cover

l. battery

3. Follow the procedure in After Working Inside Your computer.

Removing the camera

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. WLAN card

e. memory

f. keyboard

g. palmrest

h. display cable

i. system fan

j. system board

k. power connector port

l. display assembly

m. display bezel

3. To remove the camera:

a. Disconnect the camera cable from the connector on the display assembly [1].

b. Lift and remove the camera from the display assembly [2].

Installing the camera

1. Insert the camera into the slot on the display assembly.

2. Connect the camera cable to the connector on the display assembly.

3. Install the:

a. display bezel

b. display assembly

c. power connector port

d. system board

e. system fan

f. display cable

g. palmrest

h. keyboard

i. memory

j. WLAN card

k. hard drive assembly

l. base cover

m. battery

4. Follow the procedure in After Working Inside Your computer.

Removing the display panel

1. Follow the procedure in Before Working Inside Your Computer.

2. Remove the:

a. battery

b. base cover

c. hard drive assembly

d. WLAN card

e. memory

f. keyboard

g. palmrest

h. display cable

i. system fan

j. system board

k. power connector port

l. display assembly

m. display bezel

3. To remove the display panel:

a. Remove the screws that secure the display panel to the display assembly [1].

b. Remove the display panel from the display assembly [2].

c. Peel the adhesive tape [3] and disconnect the LVDS cable from the connector on the display

panel [4].

Installing the display panel

1. Connect the LVDS cable to the connector on the display panel.

2. Affix the adhesive tape to secure the LVDS cable.

3. Place the display panel aligning with the screw holders on the display assembly.

4. Tighten the screw to secure the display panel to the display assembly.

5. Install the:

a. display bezel

b. display assembly

c. power connector port

d. system board

e. system fan

f. display cable

g. palmrest

h. keyboard

i. memory

j. WLAN card

k. hard drive assembly

l. base cover

m. battery

6. Follow the procedure in After Working Inside Your computer.

System Setup

System Setup enables you to manage your computer hardware and specify BIOS level options. From the

System Setup, you can:

• Change the NVRAM settings after you add or remove hardware

• View the system hardware configuration

• Enable or disable integrated devices

• Set performance and power management thresholds

• Manage your computer security

Boot Sequence

Boot Sequence allows you to bypass the System Setup‐defined boot device order and boot directly to a

specific device (for example: optical drive or hard drive). During the Power-on Self Test (POST), when the

Dell logo appears, you can:

• Access System Setup by pressing F2 key

• Bring up the one-time boot menu by pressing F12 key

The one-time boot menu displays the devices that you can boot from including the diagnostic option.

The boot menu options are:

• Removable Drive (if available)

• STXXXX Drive

NOTE: XXX denotes the SATA drive number.

• Optical Drive

• Diagnostics

NOTE: Choosing Diagnostics, will display the ePSA diagnostics screen.

The boot sequence screen also displays the option to access the System Setup screen.

Navigation keys

The following table displays the system setup navigation keys.

NOTE: For most of the System Setup options, changes that you make are recorded but do not take

effect until you restart the system.

Table 1. Navigation keys

Keys Navigation

Up arrow Moves to the previous field.

Down arrow Moves to the next field.

Enter Allows you to select a value in the selected field (if applicable) or follow the link in

the field.

Spacebar Expands or collapses a drop‐down list, if applicable.

Tab Moves to the next focus area.

NOTE: For the standard graphics browser only.

Esc Moves to the previous page till you view the main screen. Pressing Esc in the main

screen displays a message that prompts you to save any unsaved changes and

restarts the system.

F1 Displays the System Setup help file.

System Setup overview

System Setup allows you to:

• Change the system configuration information after you add, change, or remove any hardware in your

computer.

• Set or change a user-selectable option such as the user password.

• Read the current amount of memory or set the type of hard drive installed.

Before you use System Setup, it is recommended that you write down the System Setup screen

information for future reference.

CAUTION: Unless you are an expert computer user, do not change the settings for this program.

Certain changes can cause your computer to work incorrectly.

Accessing System Setup

1. Turn on (or restart) your computer.

2. After the white Dell logo appears, press F2 immediately.

The System Setup page is displayed.

NOTE: If you wait too long and the operating system logo appears, wait until you see the

desktop. Then, shut down or restart your computer and try again.

NOTE: After the Dell logo appears, you can also press F12 and then select BIOS setup.

General screen options

This section lists the primary hardware features of your computer.

Option Description

System

Information • System Information: Displays BIOS Version, Service Tag, Asset Tag, Ownership

Tag, Ownership Date, Manufacture Date, and the Express Service Code.

• Memory Information: Displays Memory Installed, Memory Available, Memory

Speed, Memory Channels Mode, Memory Technology, DIMM A Size, DIMM B

Size.

• Processor Information: Displays Processor Type, Core Count, Processor ID,

Current Clock Speed, Minimum Clock Speed, Maximum Clock Speed,

Processor L2 Cache, Processor L3 Cache, HT Capable, and 64-Bit technology.

• Device Information: Displays Primary Hard Drive, SATA-0, M.2PCIe SSD-0, Dock

eSATA Device, LOM MAC Address, Video Controller, Video BIOS Version, Video

Memory, Panel Type, Native Resolution, Audio Controller, WiFi Device, WiGig

Device, Cellular Device, Bluetooth Device.

Battery

Information

Displays the battery status and the type of AC adapter connected to the computer.

Boot Sequence Boot Sequence Allows you to change the order in which the computer

attempts to find an operating system. The options are:

• Windows Boot Manager

• UEFI: Hard drive details

Boot List Options Allows you to change the boot list option:

• Legacy

• UEFI (enabled by default)

Advanced Boot

Options

This option allows you the legacy option ROMs to load. By default, the Enable

Legacy Option ROMs is disabled.

Date/Time Allows you to change the date and time.

System Configuration screen options

Option Description

Integrated NIC Allows you to configure the integrated network controller. The options are:

• Disabled

• Enabled

• Enabled w/PXE: This option is enabled by default.

SATA Operation Allows you to configure the internal SATA hard-drive controller. The options are:

Option Description

• Disabled

• AHCI

:This option is enabled by default.

Drives Allows you to configure the SATA drives on board. All drives are enabled by default.

The options are:

• SATA-0

SMART Reporting This field controls whether hard drive errors for integrated drives are reported

during system startup. This technology is part of the SMART (Self Monitoring

Analysis and Reporting Technology) specification. This option is disabled by default.

• Enable SMART Reporting

USB Configuration This field configures the integrated USB controller. If Boot Support is enabled, the

system is allowed to boot any type of USB Mass Storage Devices (HDD, memory

key, floppy).

If USB port is enabled, device attached to this port is enabled and available for OS.

If USB port is disabled, the OS cannot see any device attached to this port.

The options are:

• Enable USB Boot Support (by default enable)

• Enable External USB Port (by default enable)

Audio This field enables or disables the integrated audio controller. By default, the Enable

Audio option is selected. The options are:

• Enable Microphone (by default enable)

• Enable Internal Speaker (by default enable)

Keyboard

Illumination

This field lets you choose the operating mode of the keyboard illumination feature.

The keyboard brightness level can be set from 0% to 100%. The options are:

• Disabled

• Dim

• Bright (enabled by default)

Keyboard

Backlight with AC

The Keyboard Backlight with AC option does not affect the main keyboard

illumination feature. Keyboard Illumination will continue to support the various

illumination levels. This field has an effect when the backlight is enabled.

Unobtrusive Mode This option, when enabled, pressing Fn+F7 turns off all light and sound emissions

in the system. To resume normal operation, press Fn+F7 again. This option is

disabled by default.

Option Description

Miscellaneous

Devices

Allows you to enable or disable the following devices:

• Enable Microphone

• Enable Camera

• Enable Hard Drive Free Fall Protection

• Enable Media Card

• Disable Media Card

NOTE: All devices are enabled by default.

Video screen options

Option Description

LCD Brightness Allows you to set the display brightness depending up on the power source (On

Battery and On AC).

Switchable

Graphics

Allows you to enable or disable the switchable graphics technologies, such as

NVIDIA, Optimus, and AMD PowerExpress\X99.

NOTE: The video setting will be visible only when a video card is installed into the system.

Security screen options

Option Description

Admin Password Allows you to set, change, or delete the administrator (admin) password.

NOTE: You must set the admin password before you set the system or hard

drive password. Deleting the admin password automatically deletes the system

password and the hard drive password.

NOTE: Successful password changes take effect immediately.

Default setting: Not set

System Password Allows you to set, change or delete the system password.

NOTE: Successful password changes take effect immediately.

Default setting: Not set

Internal HDD-0

Password

Allows you to set, change or delete the system’s internal hard disk’s password.

Default setting: Not set

Strong Password Allows you to enforce the option to always set strong passwords.

Default Setting: Enable Strong Password is not selected.

Option Description

NOTE: If Strong Password is enabled, Admin and System passwords must

contain at least one uppercase character, one lowercase character and be at

least 8 characters long.

Password

Configuration

Allows you to determine the minimum and maximum length of Administrator and

System passwords.

Password Bypass Allows you to enable or disable the permission to bypass the System and the

Internal HDD password, when they are set. The options are:

• Disabled

• Reboot bypass

Default setting: Disabled

Password Change Allows you to enable the disable permission to the System and Hard Drive

passwords when the admin password is set.

Default setting: Allow Non-Admin Password Changes is selected.

Non-Admin Setup

Changes

Allows you to determine whether changes to the setup options are allowed when

an Administrator Password is set. If disabled the setup options are locked by the

admin password.

TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST. The options

are:

• TPM Security

• Clear

• TPM ACPI Support

• TPM PPI Provision Override

• TPM PPI Deprovision Override

• Deactivate

• Activate

NOTE: The TPM version 1.2 is supported for all Windows operating system.

NOTE: The TPM version 1.2 is for only for Windows 7/8.1 operating system.

The TPM version 1.2/2.0 is for Windows 10 operating system. You can

upgrade/downgrade for Windows 10 operating system.

CAUTION: For the TPM upgrade/downgrade process, it is recommended to

complete the process in an AC power with AC adapter plugged into the

computer. The upgrade/downgrade process without the AC adapter

plugged in might damage the computer or hard disk.

NOTE: It is recommended to use the Dell AC adapter that is shipped with the

computer.

Computrace Allows you to activate or disable the optional Computrace software The options

are:

Option Description

• Deactivate

• Disable

• Activate

NOTE: The Activate and Disable options will permanently activate or disable

the feature and no further changes will be allowed

Default setting: Deactivate

CPU XD Support Allows you to enable the Execute Disable mode of the processor.

Enable CPU XD Support (default)

Admin Setup

Lockout

Allows you to prevent users from entering the setup when an Administrator

password is set.

Default Setting: Enable Admin Setup Lockout is not selected.

Secure Boot screen options

Option Description

Secure Boot

Enable

This option enables or disables the Secure Boot feature.

• Disabled

• Enabled

Default setting: Enabled.

Expert Key

Management

Allows you to manipulate the security key databases only if the system is in Custom

Mode. The Enable Custom Mode option is disabled by default. The options are:

• PK

• KEK

• db

• dbx

If you enable the Custom Mode, the relevant options for PK, KEK, db, and dbx

appear. The options are:

•Save to File—Saves the key to a user-selected file

•Replace from File—Replaces the current key with a key from a user-selected

file

•Append from File—Adds a key to the current database from a user-selected file

•Delete—Deletes the selected key

•Reset All Keys—Resets to default setting

•Delete All Keys—Deletes all the keys

Option Description

NOTE: If you disable the Custom Mode, all the changes made will be erased

and the keys will restore to default settings.

Performance screen options

Option Description

Multi Core

Support

This field specifies whether the process has one or all cores enabled. The

performance of some applications improves with the additional cores. This option

is enabled by default. Allows you to enable or disable multi-core support for the

processor. The installed processor supports two cores. If you enable Multi Core

Support, two cores are enabled. If you disable Multi Core Support, one core is

enabled.

• Enable Multi Core Support

Default setting: The option is enabled.

Intel SpeedStep Allows you to enable or disable the Intel SpeedStep feature.

• Enable Intel SpeedStep

Default setting: The option is enabled.

C-States Control Allows you to enable or disable the additional processor sleep states.

• C states

Default setting: The option is enabled.

Hyper-Thread

Control

Allows you to enable or disable the Hyper-Threading in the processor.

• Disabled

• Enabled

Default setting: Enabled.

Power Management screen options

Option Description

AC Behavior Allows you to enable or disable the computer from turning on automatically when

an AC adapter is connected.

Default setting: Wake on AC is not selected.

Auto On Time Allows you to set the time at which the computer must turn on automatically. The

options are:

Option Description

• Disabled

• Every Day

• Weekdays

• Select Days

Default setting: Disabled

USB Wake

Support

Allows you to enable USB devices to wake the system from Standby.

NOTE: This feature is only functional when the AC power adapter is

connected. If the AC power adapter is removed during Standby, the system

setup removes power from all the USB ports to conserve battery power.

• Enable USB Wake Support

Default setting: The option is disabled.

Wireless Radio

Control

Allows you to enable or disable the feature that automatically switches from wired

or wireless networks without depending on the physical connection.

• Control WLAN Radio

Default setting: The option is disabled.

Wake on LAN/

WLAN

Allows you to enable or disable the feature that powers on the computer from the

Off state when triggered by a LAN signal.

• Disabled

• LAN Only

• WLAN Only

• LAN or WLAN

Default setting: Disabled

Block Sleep This option lets you block entering to sleep (S3 state) in operating system

environment.

Block Sleep (S3 state)

Default setting: This option is disabled

Advanced Battery

Charge

Configuration

This option enables you to maximize the battery health. By enabling this option,

your system uses the standard charging algorithm and other techniques, during the

non-work hours to improve the battery health.

Disabled

Default setting: Disabled

Option Description

Primary Battery

Charge

Configuration

Allows you to select the charging mode for the battery. The options are:

• Adaptive

• Standard — Fully charges your battery at a standard rate.

• ExpressCharge — The battery charges over a shorter period of time using Dell’s

fast charging technology. This option is enabled by default.

• Primarily AC use

• Custom

If Custom Charge is selected, you can also configure Custom Charge Start and

Custom Charge Stop.

NOTE: All charging mode may not be available for all the batteries. To enable

this option, disable the Advanced Battery Charge Configuration option.

POST Behavior screen options

Option Description

Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning messages when

you use certain power adapters.

Default setting: Enable Adapter Warnings

Fn Key Emulation Allows you to set the option where the Scroll Lock key is used to simulate the Fn

key feature.

Enable Fn Key Emulation (default)

Fn Lock Options Allows you to let hot key combinations Fn + Esc toggle the primary behavior of F1–

F12, between their standard and secondary functions. If you disable this option, you

cannot toggle dynamically the primary behavior of these keys. The available

options are:

• Fn Lock. This option is selected by default.

• Lock Mode Disable/Standard

• Lock Mode Enable/Secondary

Fastboot Allows you to speed up the boot process by bypassing some of the compatibility

steps. The options are:

• Minimal

• Thorough (default)

• Auto

Extended BIOS

POST Time

Allows you to create an additional preboot delay. The options are:

• 0 seconds. This option is enabled by default.

• 5 seconds

Option Description

• 10 seconds

Virtualization support screen options

Option Description

Virtualization Allows you to enable or disable the Intel Virtualization Technology.

Enable Intel Virtualization Technology (default).

VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the additional

hardware capabilities provided by Intel® Virtualization technology for direct I/O.

Enable VT for Direct I/O - enabled by default.

Wireless screen options

Option Description

Wireless Switch Allows to set the wireless devices that can be controlled by the wireless switch. The

options are:

• WWAN

• GPS (on WWAN Module)

• WLAN/WiGig

• Bluetooth

All the options are enabled by default.

NOTE: For WLAN and WiGig enable or disable controls are tied together and

they cannot be enabled or disabled independently.

Wireless Device

Enable

Allows you to enable or disable the internal wireless devices.

• WLAN

• Bluetooth

All the options are enabled by default.

Maintenance screen options

Option Description

Service Tag Displays the Service Tag of your computer.

Asset Tag Allows you to create a system asset tag if an asset tag is not already set. This option

is not set by default.

Option Description

BIOS Downgrade This controls flashing of the system firmware to previous revisions.

System Log screen options

Option Description

BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.

Updating the BIOS

It is recommended to update your BIOS (System Setup), on replacing the system board or if an update is

available. For laptops, ensure that your computer battery is fully charged and connected to a power

outlet

1. Restart the computer.

2. Go to Dell.com/support.

3. Enter the Service Tag or Express Service Code and click Submit.

NOTE: To locate the Service Tag, click Where is my Service Tag?

NOTE: If you cannot find your Service Tag, click Detect My Product. Proceed with the

instructions on screen.

4. If you are unable to locate or find the Service Tag, click the Product Category of your computer.

5. Choose the Product Type from the list.

6. Select your computer model and the Product Support page of your computer appears.

7. Click Get drivers and click View All Drivers.

The Drivers and Downloads page opens.

8. On the Drivers and Downloads screen, under the Operating System drop-down list, select BIOS.

9. Identify the latest BIOS file and click Download File.

You can also analyze which drivers need an update. To do this for your product, click Analyze

System for Updates and follow the instructions on the screen.

10. Select your preferred download method in the Please select your download method below window,

click Download File.

The File Download window appears.

11. Click Save to save the file on your computer.

12. Click Run to install the updated BIOS settings on your computer.

Follow the instructions on the screen.

NOTE: It is recommended not to update the BIOS version for more than 3 revisions. For example: If

you want to update the BIOS from 1.0 to 7.0, then install version 4.0 first and then install version 7.0.

System and setup password

You can create a system password and a setup password to secure your computer.

Password type Description

System password Password that you must enter to log on to your system.

Setup password Password that you must enter to access and make changes to the BIOS settings of

your computer.

CAUTION: The password features provide a basic level of security for the data on your computer.

CAUTION: Anyone can access the data stored on your computer if it is not locked and left

unattended.

NOTE: Your computer is shipped with the system and setup password feature disabled.

Assigning a system password and setup password

You can assign a new System Password and/or Setup Password or change an existing System Password

and/or Setup Password only when Password Status is Unlocked. If the Password Status is Locked, you

cannot change the System Password.

NOTE: If the password jumper is disabled, the existing System Password and Setup Password are

deleted and you need not provide the system password to log on to the computer.

To enter the system setup, press F2 immediately after a power-on or re-boot.

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen appears.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password , enter your system password, and press Enter or Tab.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only lower case letters are valid, upper case letters are not allowed.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

Re-enter the system password when prompted.

4. Type the system password that you entered earlier and click OK.

5. Select Setup Password, type your system password and press Enter or Tab.

A message prompts you to re-type the setup password.

6. Type the setup password that you entered earlier and click OK.

7. Press Esc and a message prompts you to save the changes.

8. Press Y to save the changes.

The computer reboots.

Deleting or changing an existing system and/or setup password

Ensure that the Password Status is Unlocked (in the System Setup) before attempting to delete or change

the existing System and/or Setup password. You cannot delete or change an existing System or Setup

password, if the Password Status is Locked.

To enter the System Setup, press F2 immediately after a power-on or reboot.

1. In the System BIOS or System Setup screen, select System Security and press Enter.

The System Security screen is displayed.

2. In the System Security screen, verify that Password Status is Unlocked.

3. Select System Password, alter or delete the existing system password and press Enter or Tab.

4. Select Setup Password, alter or delete the existing setup password and press Enter or Tab.

NOTE: If you change the System and/or Setup password, re-enter the new password when

promoted. If you delete the System and/or Setup password, confirm the deletion when

promoted.

5. Press Esc and a message prompts you to save the changes.

6. Press Y to save the changes and exit from System Setup.

The computer reboots.

Diagnostics

If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for

technical assistance. The purpose of running diagnostics is to test your computer's hardware without

requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service

and support personnel can use the diagnostics results to help you solve the problem.

Enhanced Pre-Boot System Assessment (ePSA)

diagnostics

The ePSA diagnostics (also known as system diagnostics) performs a complete check of your hardware.

The ePSA is embedded with the BIOS and is launched by the BIOS internally. The embedded system

diagnostics provides a set of options for particular devices or device groups allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed

device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

CAUTION: Use the system diagnostics to test only your computer. Using this program with other

computers may cause invalid results or error messages.

NOTE: Some tests for specific devices require user interaction. Always ensure that you are present

at the computer terminal when the diagnostic tests are performed.

1. Power-on the computer.

2. As the computer boots, press the F12 key as the Dell logo appears.

3. On the boot menu screen, select the Diagnostics option.

The Enhanced Pre-boot System Assessment window is displayed, listing all devices detected in the

computer. The diagnostics starts running the tests on all the detected devices.

4. To run a diagnostic test on a specific device, press Esc and click Yes to stop the diagnostic test.

5. Select the device from the left pane and click Run Tests.

6. If there are any issues, error codes are displayed.

Note the error code and contact Dell.

Device status lights

Table 2. Device status lights

Icon Description

Turns on when you turn on the computer and blinks when the computer is in a power

management mode.

Turns on steadily or blinks to indicate battery charge status.

Battery status lights

If the computer is connected to an electrical outlet, the battery light operates as follows:

Alternately blinking

amber light and

white light

An unauthenticated or unsupported non-Dell AC adapter is attached to your

laptop.

Alternately blinking

amber light with

steady white light

Temporary battery failure with AC adapter present.

Constantly blinking

amber light

Fatal battery failure with AC adapter present.

Light off Battery in full charge mode with AC adapter present.

White light on Battery in charge mode with AC adapter present.

Technical specifications

NOTE: Offerings may vary by region. For more information regarding the configuration of your

computer in:

• Windows 10, click or tap Start → Settings → System → About.

• Windows 8.1 and Windows 8, click or tap Start → PC Settings → PC and devices → PC

Info.

• Windows 7, click Start , right-click My Computer, and then select Properties.

System specifications

Feature Specification

DRAM bus width 64 bits

Flash EPROM 16 MB

Processor specifications

Feature Specification

Type 6th Generation Intel i3, i5 and i7

L1 cache 64 KB

L2 cache 256 KB

L3 cache Up to 4 MB

Memory specifications

Feature Specification

Memory

connector

two internally accessible DDR3L connectors

Memory capacity 4 GB and 8 GB

Memory type 1600 MHz (dual channel DDR3L configuration)

Minimum memory 4 GB

Feature Specification

Maximum memory 16 GB (8x2) GB

Audio specifications

Feature Specification

Types 4 channel high definition audio

Controller Realtek ALC3246

Stereo conversion 24-bit (analog-to-digital and digital-to-analog)

Interface Intel HDA bus

Speakers 2 W x 2 W

Volume controls Program menu and keyboard media-control keys

Video specifications

Feature Specification

Video Type Integrated on system board/discrete

UMA controller Intel HD 520 Graphics 6th Generation Core i3, i5, and i7

Discrete controller GT920M

Data bus 64 bits

Camera specifications

Feature Specification

Camera resolution 0.92 megapixels

Video resolution 1280x720 at 30 fps (maximum)

Diagonal viewing

angle

74°

NOTE: The RBG + IR camera is for Windows Hello application only and other

applications cannot use it.

Communication specifications

Features Specification

Network adapter 10/100/1000 Mbps Ethernet LAN on Motherboard (LOM)

Wireless Wi-Fi 802.11 b/g/n and 802.11a/b/g/n/ac

Port and connector specifications

Feature Specification

Audio one headphone/microphone combo port (headset)

Video • one 15-pin VGA port

• one 19-pin HDMI port

Network adapter one RJ-45 port

USB • two USB 3.0 ports (left one with window debug)

• one USB 2.0 port

NOTE: The powered USB 3.0 connector also supports Microsoft Kernel

Debugging. The ports are identified in the documentation shipped with your

computer.

Media card reader SD card

Memory card

reader

one (SD, SDHC, SDXC)

Fingerprint reader one (optional)

Display specifications

Feature Specification

Type 14.0 inches HD WLED

Height 205.60 mm

Width 320.90 mm

Diagonal 14.0 inches

Active area (X/Y) 309.40 mm x 173.95 mm (12.18 inches x 6.85 inches)

Maximum

resolution

1920 x 1080 pixels (FHD)1920 x 1080 pixels (FHD)

Typical brightness 200 nits

Operating angle 0° (closed) to Min 135°

Refresh rate 60 Hz

Minimum viewing

angle horizontal

40°/40°

Minimum viewing

angle vertical

10°/30°

Feature Specification

Pixel pitch 0.265 mm x 0.265 mm

External display VGA

Keyboard specifications

Feature Specification

Number of keys US 80, Brazil 82, UK 81, and Japan 84

Touchpad specifications

Feature Specification

Active Area:

X-axis 104.00 mm (4.09 inches)

Y-axis 64.00 mm (2.52 inches)

Battery specifications

Feature Specification

Type • 4-cell smart lithium ion (40 W)

• 6-cell smart lithium ion (65 W)

Height • 4-cell — 7.8 mm

• 6-cell — 7.8 mm

Width • 4-cell — 124.7 mm

• 6-cell — 124.7 mm

Depth • 4-cell — 208.25 mm

• 6-cell — 208.25 mm

Weight • 4-cell — 283 g

• 6-cell — 350 g

Voltage • 4-cell — 7.4 VDC

• 6-cell — 11.1 VDC

Feature Specification

Life span 300 discharge/charge cycles

Temperature

range:

Operating 0 °C to 50 °C (32 °F to 122 °F)

Non-operating –20 °C to 65 °C (–4 °F to 149 °F)

Coin cell battery 3 V CR2032 lithium coin cell

AC Adapter specifications

Feature Specification

Type 65 W and 90 W

Input voltage 100 V AC to 240 V AC

Input current

(maximum)

1.50 A/ 1.60 A/ 1.70 A/ 2.50 A

Input frequency 50 Hz to 60 Hz

Output current 3.34 A/ 4.62 A

Rated output

voltage

19.5 V DC

Temperature range

(Operating)

0°C to 40°C (32°F to 104°F)

Temperature range

(Non-Operating)

–40°C to 70°C (–40°F to 158°F)

Physical specifications

Feature Specification

Height (non-

touch)

23.15 mm (0.91 inches)

Height (touch) 23.15 mm (0.91 inches)

Width (non-touch) 243.30 mm (9.58 inches)

Width (touch) 243.30 mm (9.58 inches)

Depth (non-touch) 342 mm (13.46 inches)

Depth (touch) 342 mm (13.46 inches)

Minimum weight

(non-touch)

1.81 kg (4.00 lbs)

Feature Specification

Minimum weight

(touch)

1.81 kg (4.00 lbs)

Environmental specifications

Temperature Specifications

Operating 0°C to 35°C (32°F to 95°F)

Storage –40°C to 65°C (–40°F to 149°F)

Relative

humidity

(maximum)

Specifications

Operating 10 % to 90 % (non condensing)

Storage 10 % to 95 % (non condensing)

Altitude

(maximum) Specifications

Operating –15.2 m to 3048 m (–50 ft to 10,000 ft)

Non-operating –15.2 m to 10,668 m (–50 ft to 35,000 ft)

Airborne

contaminant level

G1 as defined by ISA-S71.04–1985

Contacting Dell

NOTE: If you do not have an active Internet connection, you can find contact information on your

purchase invoice, packing slip, bill, or Dell product catalog.

Dell provides several online and telephone-based support and service options. Availability varies by

country and product, and some services may not be available in your area. To contact Dell for sales,

technical support, or customer service issues:

1. Go to Dell.com/support.

2. Select your support category.

3. Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the

page.

4. Select the appropriate service or support link based on your need.

Table of Contents

DELL E3470 User Manual

Related Manuals