Table of Contents
- Dell Latitude E5530 Owner's Manual
- Working on Your Computer
- Removing and Installing Components
- Recommended Tools
- Removing the SD Card
- Installing the SD Card
- Removing the Battery
- Installing the Battery
- Removing the Subscriber Identity Module (SIM) Card
- Installing the Subscriber Identity Module (SIM) Card
- Removing the Display Bezel
- Installing the Display Bezel
- Removing the Camera
- Installing the Camera
- Removing the Display Panel
- Installing the Display Panel
- Removing the Keyboard Trim
- Installing the Keyboard Trim
- Removing the Keyboard
- Installing the Keyboard
- Removing the Access Panel
- Installing the Access Panel
- Removing the Optical Drive
- Installing the Optical Drive
- Removing The Hard Drive
- Installing the Hard Drive
- Removing the WLAN Card
- Installing the WLAN Card
- Removing the Memory Module
- Installing the Memory Module
- Removing the Right Base Panel
- Installing the Right Base Panel
- Removing the Thermal Module
- Installing the Thermal Module
- Removing the Processor
- Installing the Processor
- Removing the Palmrest
- Installing the Palmrest
- Removing the ExpressCard Reader Cage
- Installing the ExpressCard Reader Cage
- Removing the Bluetooth Module
- Installing the Bluetooth module
- Removing the Audio Board
- Installing the Audio Board
- Removing the Display Assembly
- Installing the Display Assembly
- Removing the Right Support Frame
- Installing the Right Support Frame
- Removing the Modem Card
- Installing the Modem Card
- Removing the Left Support Frame
- Installing the Left Support Frame
- Removing the System Board
- Installing the System Board
- Removing the Coin-Cell Battery
- Installing the Coin-Cell Battery
- Removing the Input/Output (I/O) Board
- Installing the Input/Output (I/O) Board
- Removing the Power Connector
- Installing the Power Connector
- Removing the System Fan
- Installing the System Fan
- Removing the Network Connector
- Installing the Network Connector Jack
- Removing the Speakers
- Installing the Speakers
- Specifications
- Docking Port Information
- Additional Information
- System Setup
- Diagnostics
- Contacting Dell
DELL E5530 User Manual
Displayed below is the user manual for E5530 by DELL which is a product in the Notebooks category. This manual has pages.
Related Manuals
Dell Latitude E5530
Owner's Manual
Regulatory Model: P28G
Regulatory Type: P28G001
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use of your computer.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal injury, or death.
© 2013 Dell Inc. All Rights Reserved.
Trademarks used in this text: Dell™, the Dell logo, Dell Boomi™, Dell Precision™ , OptiPlex™, Latitude™, PowerEdge™,
PowerVault™, PowerConnect™, OpenManage™, EqualLogic™, Compellent™, KACE™, FlexAddress™, Force10™, Venue™
and Vostro™ are trademarks of Dell Inc. Intel®, Pentium®, Xeon®, Core® and Celeron® are registered trademarks of
Intel Corporation in the U.S. and other countries. AMD® is a registered trademark and AMD Opteron™, AMD Phenom™
and AMD Sempron™ are trademarks of Advanced Micro Devices, Inc. Microsoft®, Windows®, Windows Server®,
Internet Explorer®, MS-DOS®, Windows Vista® and Active Directory® are either trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries. Red Hat® and Red Hat® Enterprise Linux® are
registered trademarks of Red Hat, Inc. in the United States and/or other countries. Novell® and SUSE® are registered
trademarks of Novell Inc. in the United States and other countries. Oracle® is a registered trademark of Oracle
Corporation and/or its affiliates. Citrix®, Xen®, XenServer® and XenMotion® are either registered trademarks or
trademarks of Citrix Systems, Inc. in the United States and/or other countries. VMware®, vMotion®, vCenter®,
vCenter SRM™ and vSphere® are registered trademarks or trademarks of VMware, Inc. in the United States or other
countries. IBM® is a registered trademark of International Business Machines Corporation.
2013 – 12
Rev. A01
Contents
1 Working on Your Computer................................................................................... 7
Before Working Inside Your Computer................................................................................................ 7
Turning Off Your Computer..................................................................................................................9
After Working Inside Your Computer................................................................................................... 9
2 Removing and Installing Components.............................................................. 11
Recommended Tools.......................................................................................................................... 11
Removing the SD Card........................................................................................................................ 11
Installing the SD Card.......................................................................................................................... 11
Removing the Battery..........................................................................................................................12
Installing the Battery............................................................................................................................12
Removing the Subscriber Identity Module (SIM) Card....................................................................... 13
Installing the Subscriber Identity Module (SIM) Card......................................................................... 13
Removing the Display Bezel................................................................................................................13
Installing the Display Bezel..................................................................................................................14
Removing the Camera........................................................................................................................ 14
Installing the Camera...........................................................................................................................15
Removing the Display Panel................................................................................................................15
Installing the Display Panel..................................................................................................................17
Removing the Keyboard Trim............................................................................................................. 17
Installing the Keyboard Trim............................................................................................................... 19
Removing the Keyboard..................................................................................................................... 20
Installing the Keyboard....................................................................................................................... 22
Removing the Access Panel................................................................................................................23
Installing the Access Panel................................................................................................................. 24
Removing the Optical Drive............................................................................................................... 24
Installing the Optical Drive................................................................................................................. 26
Removing The Hard Drive...................................................................................................................26
Installing the Hard Drive..................................................................................................................... 28
Removing the WLAN Card..................................................................................................................28
Installing the WLAN Card....................................................................................................................29
Removing the Memory Module..........................................................................................................29
Installing the Memory Module............................................................................................................29
Removing the Right Base Panel..........................................................................................................29
Installing the Right Base Panel........................................................................................................... 30
Removing the Thermal Module..........................................................................................................30
Installing the Thermal Module............................................................................................................ 31
Removing the Processor.....................................................................................................................32
Installing the Processor.......................................................................................................................32
Removing the Palmrest.......................................................................................................................32
Installing the Palmrest.........................................................................................................................34
Removing the ExpressCard Reader Cage.......................................................................................... 35
Installing the ExpressCard Reader Cage............................................................................................ 35
Removing the Bluetooth Module....................................................................................................... 36
Installing the Bluetooth module.........................................................................................................36
Removing the Audio Board.................................................................................................................37
Installing the Audio Board...................................................................................................................37
Removing the Display Assembly.........................................................................................................38
Installing the Display Assembly.......................................................................................................... 40
Removing the Right Support Frame................................................................................................... 41
Installing the Right Support Frame..................................................................................................... 41
Removing the Modem Card............................................................................................................... 42
Installing the Modem Card................................................................................................................. 42
Removing the Left Support Frame..................................................................................................... 43
Installing the Left Support Frame....................................................................................................... 43
Removing the System Board.............................................................................................................. 44
Installing the System Board................................................................................................................ 47
Removing the Coin-Cell Battery........................................................................................................48
Installing the Coin-Cell Battery..........................................................................................................48
Removing the Input/Output (I/O) Board............................................................................................49
Installing the Input/Output (I/O) Board..............................................................................................50
Removing the Power Connector........................................................................................................51
Installing the Power Connector..........................................................................................................52
Removing the System Fan.................................................................................................................. 53
Installing the System Fan.................................................................................................................... 54
Removing the Network Connector....................................................................................................55
Installing the Network Connector Jack............................................................................................. 55
Removing the Speakers...................................................................................................................... 56
Installing the Speakers.........................................................................................................................57
3 Specifications.......................................................................................................... 59
Specifications...................................................................................................................................... 59
4 Docking Port Information....................................................................................65
5 Additional Information..........................................................................................67
6 System Setup........................................................................................................... 69
Overview .............................................................................................................................................69
Entering System Setup........................................................................................................................69
System Setup Options........................................................................................................................ 69
7 Diagnostics............................................................................................................... 79
Diagnostics.......................................................................................................................................... 79
8 Contacting Dell....................................................................................................... 81
6
1
Working on Your Computer
Before Working Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help to
ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes
that the following conditions exist:
• You have read the safety information that shipped with your computer.
• A component can be replaced or--if purchased separately--installed by performing the removal
procedure in reverse order.
WARNING: Before working inside your computer, read the safety information that shipped with
your computer. For additional safety best practices information, see the Regulatory Compliance
Homepage at www.dell.com/regulatory_compliance
CAUTION: Many repairs may only be done by a certified service technician. You should only
perform troubleshooting and simple repairs as authorized in your product documentation, or as
directed by the online or telephone service and support team. Damage due to servicing that is
not authorized by Dell is not covered by your warranty. Read and follow the safety instructions
that came with the product.
CAUTION: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or
by periodically touching an unpainted metal surface, such as a connector on the back of the
computer.
CAUTION: Handle components and cards with care. Do not touch the components or contacts
on a card. Hold a card by its edges or by its metal mounting bracket. Hold a component such as a
processor by its edges, not by its pins.
CAUTION: When you disconnect a cable, pull on its connector or on its pull-tab, not on the cable
itself. Some cables have connectors with locking tabs; if you are disconnecting this type of cable,
press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable,
ensure that both connectors are correctly oriented and aligned.
NOTE: The color of your computer and certain components may appear differently than shown in
this document.
To avoid damaging your computer, perform the following steps before you begin working inside the
computer.
1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched.
2. Turn off your computer (see Turning Off Your Computer).
7
3. If the computer is connected to a docking device (docked) such as the optional Media Base or
Battery Slice, undock it.
CAUTION: To disconnect a network cable, first unplug the cable from your computer and
then unplug the cable from the network device.
4. Disconnect all network cables from the computer.
5. Disconnect your computer and all attached devices from their electrical outlets.
6. Close the display and turn the computer upside-down on a flat work surface.
NOTE: To avoid damaging the system board, you must remove the main battery before you
service the computer.
7. Remove the main battery.
8. Turn the computer top-side up.
9. Open the display.
10. Press the power button to ground the system board.
CAUTION: To guard against electrical shock, always unplug your computer from the
electrical outlet before opening the display.
CAUTION: Before touching anything inside your computer, ground yourself by touching an
unpainted metal surface, such as the metal at the back of the computer. While you work,
periodically touch an unpainted metal surface to dissipate static electricity, which could
harm internal components.
11. Remove any installed ExpressCards or Smart Cards from the appropriate slots.
8
Turning Off Your Computer
CAUTION: To avoid losing data, save and close all open files and exit all open programs before
you turn off your computer.
1. Shut down the operating system:
– In Windows 8:
* Using a touch-enabled device:
a. Swipe in from the right edge of the screen, opening the Charms menu and select
Settings.
b. Select the and then select Shut down
* Using a mouse:
a. Point to upper-right corner of the screen and click Settings.
b. Click the and select Shut down.
– In Windows 7:
1. Click Start .
2. Click Shut Down.
or
1. Click Start .
2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click
Shut Down..
2. Ensure that the computer and all attached devices are turned off. If your computer and attached
devices did not automatically turn off when you shut down your operating system, press and hold
the power button for about 4 seconds to turn them off.
After Working Inside Your Computer
After you complete any replacement procedure, ensure you connect any external devices, cards, and
cables before turning on your computer.
CAUTION: To avoid damage to the computer, use only the battery designed for this particular
Dell computer. Do not use batteries designed for other Dell computers.
1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any
cards, such as an ExpressCard.
2. Connect any telephone or network cables to your computer.
CAUTION: To connect a network cable, first plug the cable into the network device and then
plug it into the computer.
3. Replace the battery.
4. Connect your computer and all attached devices to their electrical outlets.
9
5. Turn on your computer.
10
2
Removing and Installing Components
This section provides detailed information on how to remove or install the components from your
computer.
Recommended Tools
The procedures in this document may require the following tools:
• Small flat-blade screwdriver
• #0 Phillips screwdriver
• #1 Phillips screwdriver
• Small plastic scribe
Removing the SD Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Press in on the SD card to release it from the computer.
3. Slide the SD card out of the computer.
Installing the SD Card
1. Push the SD card into the compartment until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
11
Removing the Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Slide the battery release latches into the unlock position.
3. Remove the battery from the computer.
Installing the Battery
1. Slide the battery into its slot until it clicks into place.
2. Follow the procedures in After Working Inside Your Computer.
12
Removing the Subscriber Identity Module (SIM) Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the battery.
3. Press and release the SIM card located on the battery wall.
4. Slide the SIM card from the computer.
Installing the Subscriber Identity Module (SIM) Card
1. Insert the subscriber identity module (SIM) card into the slot.
2. Install the battery.
3. Follow the procedures in After Working Inside Your Computer.
Removing the Display Bezel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the battery.
3. Pry up the bottom edge of the display bezel.
13
4. Work your way around the sides and top edge of the display bezel. .
5. Remove the display bezel from the computer .
Installing the Display Bezel
1. Place the display bezel onto the display assembly.
2. Starting from the top corner, press on the display bezel and work around the entire bezel until it
snaps onto the display assembly.
3. Install the battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Camera
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) display bezel
3. Perform the following steps:
a) Remove the screw that secures the camera and microphone module.
b) Disconnect the camera cable.
c) Lift and remove the camera and microphone module.
14
Installing the Camera
1. Place the camera and microphone module on its place.
2. Connect the camera cable.
3. Tighten the screw to secure the camera and microphone module.
4. Install:
a) display bezel
b) battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Display Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) display bezel
3. Remove the screws that secure the display panel.
15
4. Flip the display panel over.
5. Lift the Mylar tape and disconnect the LVDS cable from the back of the display panel.
16
6. Remove the display panel from the display assembly.
Installing the Display Panel
1. Install the screws that secure the display brackets to the display panel.
2. Attach the display panel to the display assembly.
3. Align the display panel in its original position in the computer.
4. Connect the low-voltage differential signaling (LVDS) cable to the display panel and attach the tape.
5. Flip the display panel over and install the screws that secure the display panel.
6. Install:
a) display bezel
b) battery
7. Follow the procedures in After Working Inside Your Computer.
Removing the Keyboard Trim
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the battery.
17
3. Remove the screws at the back of the computer.
4. Pry up the keyboard trim starting from the bottom edge.
5. Work your way around the sides and the top edge of the keyboard trim.
18
6. Lift upwards and remove the keyboard trim from the computer.
Installing the Keyboard Trim
1. Align the keyboard trim to its place.
2. Press along the sides of the keyboard trim until it snaps in place.
3. Install the battery.
4. Follow the procedures in After Working Inside Your Computer.
19
Removing the Keyboard
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) keyboard trim
3. Remove the screw at the back of the computer.
4. Lift the clip to release the keyboard trim from the computer .
20
5. Remove the keyboard trim from the computer .
6. Remove the screws that secure the keyboard in place.
21
7. Flip the keyboard over.
8. Peel off the adhesive tape securing the keyboard flat flex cable to the back of the keyboard.
9. Disconnect the keyboard flat flex cable.
10. Peel away the keyboard flat flex cable from the keyboard and remove it from the computer.
Installing the Keyboard
1. Attach the keyboard flat flex cable to the keyboard.
2. Affix the adhesive tape securing the keyboard flat flex cable to the keyboard.
3. Slide the keyboard into its compartment until all the metal tabs fit into their positions.
4. Fasten the keyboard cable clip.
5. Press down on the keyboard to the left and right side ensuring that all the snaps are fully engaged
with the computer.
6. Install the screws that secure the keyboard to the palm rest.
22
7. Install the screw at the back of the computer.
8. Install :
a) keyboard trim
b) battery
9. Follow the procedures in After Working Inside Your Computer.
Removing the Access Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove the battery.
3. Remove the screws that secure the access panel.
4. Slide and then lift the access panel upwards and remove it from the computer.
23
Installing the Access Panel
1. Slide the access panel into its slot until it clicks into place.
2. Install the screws that secure the access panel to the computer.
3. Install the battery.
4. Follow the procedures in After Working Inside Your Computer.
Removing the Optical Drive
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) access panel
3. Remove the screw that secures the optical drive.
24
4. Push the screw tab away from the computer to release the optical drive from the drive bay.
5. Remove the optical drive from the computer.
6. Remove the screws that secure the optical drive bracket.
7. Remove the optical drive bracket.
8. Disengage the optical drive bezel tabs to separate the optical drive bezel from the optical drive.
9. Remove the optical drive bezel.
25
Installing the Optical Drive
1. Engage the optical drive bezel tabs to attach the optical drive bezel to the optical drive.
2. Install the optical drive bracket.
3. Install the screws that secure the optical drive bracket.
4. Insert the optical drive into the computer.
5. Install the screw that secures the optical drive in place.
6. Install :
a) access panel
b) battery
7. Follow the procedures in After Working Inside Your Computer.
Removing The Hard Drive
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) access panel
3. Remove the screws that secure the hard drive bracket in place.
26
4. Use the tab to pull the hard drive bracket and release the hard drive from its connector.
5. Remove the hard drive from the computer.
27
6. Remove the screws that secure the hard drive bracket.
7. Remove the hard drive bracket from the hard drive.
Installing the Hard Drive
1. Engage the hard drive bracket to the hard drive.
2. Install the screws that secure the hard drive bracket.
3. Install the hard drive into the computer.
4. Install the screw that secures the hard drive bracket in place.
5. Install:
a) base panel
b) battery
6. Follow the procedures in After Working Inside Your Computer.
Removing the WLAN Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) base cover
3. Perform the following steps:
a) Disconnect the antennae cables from the WLAN card.
b) Remove the screw that secures the WLAN card to the computer.
c) Remove the WLAN card from its slot on the system board.
28
Installing the WLAN Card
1. Insert the WLAN card into its connector on the system board.
2. Connect the antenna cables to the respective connectors marked on the WLAN card.
3. Tighten the screw to secure the WLAN card to the computer.
4. Install:
a) base cover
b) battery
5. Follow the procedures in After Working Inside Your Computer.
Removing the Memory Module
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) base cover
3. Pry the retention clips away from the memory module until it pops up.
4. Lift up the memory module and remove it from the computer.
Installing the Memory Module
1. Insert the memory into the memory socket.
2. Press the clips to secure the memory module to the system board.
3. Install:
a) base cover
b) battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the Right Base Panel
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) battery
b) access panel
29
3. Remove the screws that secure the right base panel in place.
4. Remove the right base panel from the computer.
Installing the Right Base Panel
1. Place the right base panel in its location at the bottom of the computer.
2. Install the screws that secure the right base panel to the bottom of the computer.
3. Install :
a) access panel
b) battery
4. Follow the procedures in After Working Inside Your Computer.
Removing the Thermal Module
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) right base panel
30
3. Remove the screws that secure the thermal module in place.
4. Lift up the thermal module and remove it from the computer.
Installing the Thermal Module
1. Place the thermal module in its compartment.
2. Install the screws that secure the thermal module to the computer.
3. Install :
a) right base panel
b) access panel
c) battery
d) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
31
Removing the Processor
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) right base panel
e) thermal module
3. Rotate the processor cam lock in a counter clockwise direction to the unlock position. Lift up the
processor and remove it from the computer.
Installing the Processor
1. Place the processor in its socket on the computer.
2. Rotate the processor cam lock in a clockwise direction to secure the processor.
3. Install:
a) thermal module
b) access panel
c) right base panel
d) battery
e) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
Removing the Palmrest
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) right base panel
h) hard drive
32
3. Remove the screws that secure the bottom of the computer.
4. Disconnect the :
a) LED board flat flex cable
b) media button flat flex cable
c) touchpad flat flex cable
d) fingerprint scanner flat flex cable
e) power button flat flex cable
33
5. Remove the screws that secure the palmrest on the computer.
6. Lift up the right edge of palmrest assembly.
7. Release the tabs on the left edge of the palmrest assembly and remove the palmrest from the
computer.
Installing the Palmrest
1. Align the palmrest assembly to its original position in the computer and snap it into place.
2. Connect the following cables to the system board:
a) power button flat flex cable.
b) fingerprint scanner flat flex cable
c) touchpad flat flex cable
d) media button flat flex cable
e) LED board flat flex cable
3. Install the screws on the palmrest.
34
4. Install the screws at the bottom of the computer.
5. Install :
a) right base panel
b) optical drive
c) keyboard
d) keyboard trim
e) access panel
f) battery
g) SD memory card
6. Follow the procedures in After Working Inside Your Computer.
Removing the ExpressCard Reader Cage
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) right base panel
h) palmrest
3. Remove the screws that secure the ExpressCard reader cage in place.
4. Remove the ExpressCard reader cage from the computer.
Installing the ExpressCard Reader Cage
1. Align the ExpressCard reader cage to its original position in the computer and snap it into place.
2. Install the screws that secure the ExpressCard reader cage.
3. Install:
a) palmrest
b) right base panel
c) optical drive
d) keyboard
e) keyboard trim
f) access panel
g) battery
h) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
35
Removing the Bluetooth Module
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) right base panel
h) palm rest
3. Disconnect the Bluetooth cable from the system board and remove the screw that secures the
Bluetooth module in place.
4. Remove the Bluetooth module from the computer.
5. Disconnect the Bluetooth cable from the Bluetooth module.
Installing the Bluetooth module
1. Connect the Bluetooth cable to the Bluetooth module.
2. Place the Bluetooth module into its compartment on the computer.
3. Install the screw that secures the Bluetooth module.
4. Connect the Bluetooth cable to the system board.
5. Install :
a) palm rest
b) right base panel
c) optical drive
d) keyboard
e) keyboard trim
f) access panel
g) battery
h) SD memory card
6. Follow the procedures in After Working Inside Your Computer.
36
Removing the Audio Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) right base panel
h) palmrest
i) bluetooth module
3. Disconnect the audio board flat flex cable from the system board and remove the screw that secures
the audio board in place.
4. Remove the audio board from the computer.
Installing the Audio Board
1. Place the audio board in the computer.
2. Tighten the screw to secure the audio board to the computer.
3. Connect the audio board cable to the system board.
4. Install:
a) Bluetooth module
b) palmrest
c) right base panel
d) optical drive
e) keyboard
f) keyboard trim
g) access panel
h) battery
i) SD memory card
5. Follow the procedures in After Working Inside Your Computer.
37
Removing the Display Assembly
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) right base panel
i) palmrest
3. Disconnect and remove any antennas from the routing channels.
38
4. Disconnect the low-voltage differential signaling (LVDS) cable.
5. Pull the antennas through the opening to the top of the computer.
6. Lift up the connector indicated on the system board.
39
7. Remove the screws that secure the display assembly in place.
8. Remove the display assembly from the computer.
Installing the Display Assembly
1. Install the screws that secure the display assembly in place.
2. Insert the low-voltage differential signaling (LVDS) cable and wireless antenna cables through the
holes on the chassis.
3. Route the LVDS cable along its compartment and connect the connector to the system board.
4. Connect the antenna cables to their connectors.
5. Install :
a) palmrest
b) right access panel
c) optical drive
d) keyboard
e) keyboard trim
f) access panel
g) battery
h) SD memory card
6. Follow the procedures in After Working Inside Your Computer.
40
Removing the Right Support Frame
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) optical drive
f) hard drive
g) right base panel
h) palmrest
i) display assembly
3. Remove the screws that secure the right support frame to the computer.
4. Lift the right support frame away from the computer.
Installing the Right Support Frame
1. Place the right support frame on the computer.
2. Tighten the screws to secure the right support frame to the computer.
3. Install:
a) display assembly
b) palmrest
c) right base panel
d) hard drive
e) optical drive
f) keyboard
g) keyboard trim
h) access panel
i) battery
j) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
41
Removing the Modem Card
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) right base panel
i) palmrest
j) display assembly
k) right support frame
3. Remove the screw that secures the modem card to the computer.
4. Lift the modem card to disengage from the connector on the back of the card.
5. Disconnect the network connector cable from the modem card.
6. Lift the modem card from the computer.
Installing the Modem Card
1. Place the modem card on the Input/Output (I/O) board in the computer.
2. Connect the network connector cable to the modem card.
3. Engage the modem card to the connector located at the back of the computer.
4. Tighten the screw to secure the modem card to the computer.
5. Install:
a) right support frame
b) display assembly
c) palmrest
d) right base panel
e) hard drive
f) optical drive
g) keyboard
h) keyboard trim
i) access panel
j) battery
k) SD memory card
42
6. Follow the procedures in After Working Inside Your Computer.
Removing the Left Support Frame
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) right base panel
i) palmrest
j) display assembly
3. Remove the screws that secure the left support frame to the computer.
4. Lift the left support frame away from the computer.
Installing the Left Support Frame
1. Place the left support frame on the computer.
2. Tighten the screws to secure the left support frame to the computer.
43
3. Install:
a) display assembly
b) palmrest
c) right base panel
d) hard drive
e) optical drive
f) keyboard
g) keyboard trim
h) access panel
i) battery
j) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
Removing the System Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) WLAN card
i) right base panel
j) thermal module
k) palmrest
l) ExpressCard reader cage
m) display assembly
n) left support frame
o) thermal fan cable
44
3. Disconnect:
a) thermal fan cable
b) DC-in cable
c) Bluetooth cable
4. Disconnect the speaker cable and the audio board flex cable from the system board.
45
5. Remove the screws that secure the system board.
6. Lift the right edge of the system board assembly and raise it to a 45–degree angle.
46
7. Release the system board from the port connectors on the left and remove the system board.
Installing the System Board
1. Align the system board into its original position on the computer.
2. Replace and tighten the screws to secure the system board to the computer.
3. Route and connect the following cables the system board:
a) audio board flat flex cable
b) Bluetooth cable
c) speaker cable
d) DC-in cable
e) thermal fan cable
4. Install :
a) left support frame
b) display assembly
c) ExpressCard reader cage
d) palm rest
e) thermal module
f) right base panel
g) hard drive
h) optical drive
i) keyboard
j) keyboard trim
k) access panel
l) battery
m) SD memory card
5. Follow the procedures in After Working Inside Your Computer.
47
Removing the Coin-Cell Battery
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) ExpressCard
c) battery
d) access panel
e) keyboard trim
f) optical drive
g) hard drive
h) WLAN card
i) right base panel
j) thermal module
k) palmrest
l) ExpressCard reader cage
m) display assembly
n) left support frame
o) system board
3. Disconnect the coin-cell battery from the system board.
4. Pry the coin-cell battery from the adhesive and remove it.
Installing the Coin-Cell Battery
1. Place the coin-cell battery on the system board with adhesive side downwards.
2. Connect the coin-cell battery cable to the system board.
48
3. Install:
a) system board
b) left support frame
c) display assembly
d) ExpressCard reader cage
e) palmrest
f) thermal module
g) right base panel
h) WLAN card
i) hard drive
j) optical drive
k) keyboard
l) keyboard trim
m) access panel
n) battery
o) ExpressCard
p) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
Removing the Input/Output (I/O) Board
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) WLAN card
i) right base panel
j) thermal module
k) palmrest
l) ExpressCard reader cage
m) display assembly
n) right support frame
o) left support frame
p) system board
3. Remove the screws that secure the Input/Output (I/O) board in the computer.
49
4. Lift the Input/Output (IO) board out of the computer.
Installing the Input/Output (I/O) Board
1. Place the Input/Output (I/O) board in the computer.
2. Tighten the screw to secure the Input/Output (I/O) board to the computer.
3. Install:
a) system board
b) left support frame
c) right support frame
d) display assembly
e) ExpressCard reader cage
f) palmrest
g) thermal module
h) right base panel
i) WLAN card
j) hard drive
k) optical drive
l) keyboard
m) keyboard trim
n) access panel
o) battery
p) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
50
Removing the Power Connector
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) WLAN card
i) right base panel
j) thermal module
k) palmrest
l) ExpressCard reader cage
m) display assembly
n) left support bracket
o) system board
3. Remove the power connector cable from the routing channels.
51
4. Remove the power connector.
Installing the Power Connector
1. Install the power connector in the computer.
2. Thread the power connector cable in the routing channel.
3. Install:
a) system board
b) left support bracket
c) display assembly
d) ExpressCard reader cage
e) palmrest
f) thermal module
g) right base panel
h) WLAN card
i) hard drive
j) optical drive
k) keyboard
l) keyboard trim
m) access panel
n) battery
o) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
52
Removing the System Fan
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) WLAN card
i) right base panel
j) thermal module
k) palmrest
l) ExpressCard reader cage
m) display assembly
n) right support frame
o) left support frame
p) modem card
q) network connector
r) system board
s) power connector
3. Remove the system fan cable from the routing channel.
53
4. Remove the screw that secures the system fan and lift it to remove from the computer.
Installing the System Fan
1. Place the system fan in the computer.
2. Tighten the screws to secure the fan to the computer.
3. Install:
a) power connector
b) system board
c) network connector
d) modem card
e) left support frame
f) right support frame
g) display assembly
h) ExpressCard reader cage
i) palmrest
j) thermal module
k) right base panel
l) WLAN card
m) hard drive
n) optical drive
o) keyboard
p) keyboard trim
q) access panel
r) battery
s) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
54
Removing the Network Connector
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) right base panel
i) palmrest
j) display assembly
k) right support frame
l) left support frame
m) modem card
3. Remove the network connector cables from the routing channels.
4. Remove the network connector jack.
Installing the Network Connector Jack
1. Install the network connector jack in the computer.
2. Thread the network connector cable in the routing channel.
55
3. Install:
a) modem card
b) left support frame
c) right support frame
d) display assembly
e) palmrest
f) right base panel
g) hard drive
h) optical drive
i) keyboard
j) keyboard trim
k) access panel
l) battery
m) SD memory card
4. Follow the procedures in After Working Inside Your Computer.
Removing the Speakers
1. Follow the procedures in Before Working Inside Your Computer.
2. Remove:
a) SD memory card
b) battery
c) access panel
d) keyboard trim
e) keyboard
f) optical drive
g) hard drive
h) WLAN card
i) right base panel
j) thermal module
k) palmrest
l) ExpressCard reader cage
m) Bluetooth module
n) audio board
o) display assembly
p) left support frame
q) system board
56
3. Remove the screws that secure the speakers.
4. Remove the speaker cables from the routing channels.
5. Lift the speaker out from the computer.
Installing the Speakers
1. Place the speakers in the computer.
2. Tighten the screws to secure the speakers to the computer.
3. Connect the speaker cables and secure it in the routing channels.
57
4. Install:
a) system board
b) left support frame
c) display assembly
d) audio board
e) Bluetooth module
f) ExpressCard reader cage
g) palmrest
h) thermal module
i) right base panel
j) WLAN card
k) hard drive
l) optical drive
m) keyboard
n) keyboard trim
o) access panel
p) battery
q) SD memory card
5. Follow the procedures in After Working Inside Your Computer.
58
3
Specifications
Specifications
NOTE: Offerings may vary by region. For more information regarding the configuration of your
computer, click Start (Start icon) → Help and Support, and then select the option to view
information about your computer.
Table 1. System Information
Feature Specification
Chipset Intel HM77/QM77 Express Chipset
DRAM bus width 64-bit
Flash EPROM SPI 32 Mbits
PCIe Gen1 bus 100 MHz
External Bus Frequency DMI (5GT/s)
Table 2. Processor
Feature Specification
Types • Intel Celeron
• Intel Core i3 series
• Intel Core i5 series
• Intel Core i7 series
L3 cache up to 8MB
Table 3. Memory
Feature Specification
Memory connector two SoDIMM slots
Memory capacity 2 GB, 4 GB, or 8 GB
Memory type DDR3 SDRAM 1600
Minimum memory 2 GB
Maximum memory 8 GB
59
Table 4. Audio
Feature Specification
Type four-channel high definition audio
Controller IDT92HD93
Stereo conversion 24-bit (analog-to-digital and digital-to-analog)
Interface:
Internal high definition audio
External microphone-in/stereo headphones/external speakers
connector
Speakers two
Internal speaker amplifier 1W (RMS) per channel
Volume controls keyboard function keys, program menus
Table 5. Video
Feature Specification
Type integrated on system board
Controller Intel HD Graphics
Table 6. Communications
Feature Specification
Network adapter 10/100/1000 Mb/s Ethernet (RJ-45)
Wireless internal wireless local area network (WLAN) and wireless
wide area network (WWAN)
Table 7. Ports and Connectors
Feature Specification
Audio (optional) one microphone/stereo headphone/speakers connector
Video • one 15-pin VGA connector
• 19-pin HDMI connector
Network adapter one RJ-45 connector
USB 2.0 • two 4-pin USB 2.0-compliant connector
USB 3.0 • one USB 3.0-compliant connector
• oOne eSATA/USB 3.0-compliant connector
Memory card reader one 8-in-1 memory card reader
Docking port one
60
Feature Specification
Subscriber Identity Module (SIM) port one
Table 8. Display
Feature Specification
Type
Latitude E5430 • HD(1366x768), WLED
• HD+(1600 x 900)
Latitude E5530 • HD(1366x768), WLED
• FHD (1920 x 1080)
Size
Latitude E5430 14.0"
Latitude E5530 15.6"
Dimensions:
Latitude E5430:
Height 192.5 mm (7.57 inches)
Width 324 mm (12.75 inches)
Diagonal 355.60 mm (14.00 inches)
Active ares (X/Y) 309.40 mm x 173.95 mm
Maximum resolution • 1366 x 768 pixels
• 1600 x 900 pixels
Maximum Brightness 200 nits
Latitude E5530:
Height 210 mm (8.26 inches)
Width 360 mm (14.17 inches)
Diagonal 394.24 mm (15.60 inches)
Active area (X/Y) 344.23 mm x 193.54 mm
Maximum resolution • 1366 x 768 pixels
• 1920 x 1080 pixels
Maximum Brightness 220 nits for HD, 300 nits for FHD
Operating angle 0° (closed) to 135°
Refresh rate 60 Hz
Minimum Viewing angles:
61
Feature Specification
Horizontal • +/- 40° for HD
• +/- 60° for FHD
Vertical • +10°/-30° for HD
• +/-50° for FHD
Pixel pitch:
Latitude E5430 0.2265 mm x 0.2265 mm
Latitude E5530 • 0.2520 mm x 0.2520 mm for HD
• 0.1790 x 0.1790 for FHD
Table 9. Keyboard
Feature Specifcation
Number of keys United States: 86 keys, United Kingdom: 87 keys, Brazil:
87 keys, and Japan: 90 keys
Layout QWERTY/AZERTY/Kanji
Table 10. Touchpad
Feature Specification
Active Area:
X-axis 80.00 mm
Y-axis 45.00 mm
Table 11. Battery
Feature Specification
Type 4, 6 or 9-cell "smart" lithium ion
Dimensions:
Height
4-, 6-, and 9-cell 20.00 mm (0.79 inch)
Width
4- and 6-cell 208.00 mm (8.18 inches)
9-cell 214.00 mm (8.43 inches)
Depth
4- and 6-cell 48.08 mm (1.89 inches)
9-cell 71.79 mm (2.83 inches)
Weight
62
Feature Specification
4-cell 240.00 g (0.53 lb)
6-cell 344.73 g (0.76 lb)
9-cell 508.20 g (1.12 lb)
Voltage
4-cell 14.8 VDC
6- and 9-cell 11.1 VDC
Temperature range:
Operating 0 °C to 50 °C (32 °F to 122 °F)
Non-Operating –40 °C to 85 °C (–40 °F to 185 °F)
NOTE: The battery pack is capable of safely
withstanding the above storage temperatures
with 100% charge.
NOTE: The battery pack is also capable of
withstanding storage temperatures from –20
°C to +60 °C with no degradation in its
performance.
Coin-cell battery 3 V CR2032 lithium coin cell
Table 12. AC Adapter
Feature Latitude E5430 Latitude E5530
Type 65 W 90 W adapter
Input voltage 100 VAC to 240 VAC 100 VAC to 240 VAC
Input current (maximum) 1.7 A 1.5 A
Input frequency 50 Hz to 60 Hz 50 Hz to 60 Hz
Output power 65 W 90 W
Output current 3.34 A (continuous) 4.62 A (continuous)
Rated output voltage 19.5 +/– 1.0 VDC 19.5 +/– 1.0 VDC
Temperature range:
Operating 0 °C to 40 °C (32 °F to 104 °F) 0 °C to 40 °C (32 °F to 104 °F)
Non-Operating –40 °C to 70 °C (–40 °F to 158 °F) –40 °C to 70 °C (–40 °F to 158 °F)
Table 13. Physical
Physical Latitude E5430 Latitude E5530
Height 29.9 mm to 32.5 mm (1.17 inches to
1.27 inches)
30.20 mm to 33.2 mm (1.18 inches
to 1.30 inches)
Width 350.00 mm (13.70 inches) 388.00 mm (15.27 inches)
63
Physical Latitude E5430 Latitude E5530
Depth 240.00 mm (9.44 inches) 251.00 mm (9.88 inches)
Weight 2.04 kg (4.50 lb) 2.38 kg (5.25 lb)
Table 14. Environmental
Feature Specification
Temperature:
Operating 0 °C to 35 °C (32 °F to 95 °F)
Storage –40 °C to 65 °C (–40 °F to 149 °F)
Relative humidity (maximum):
Operating 10 % to 90 % (non condensing)
Storage 5 % to 95 % (non condensing)
Altitude (maximum):
Operating –15.24 m to 3048 m (–50 ft to 10,000 ft)
Non-Operating –15.24 m to 10,668 m (–50 ft to 35,000 ft)
Airborne contaminant level G1 as defined by ISA-71.04–1985
64
4
Docking Port Information
The docking port is used for connecting the laptop to a docking station (optional).
1. SIM card slot
2. Docking Port
65
66
5
Additional Information
This section provides information for the additional features that are part of your computer.
67
68
6
System Setup
Overview
System Setup allows you to:
• change the system configuration information after you add, change, or remove any hardware in your
computer.
• set or change a user-selectable option such as the user password.
• read the current amount of memory or set the type of hard drive installed.
CAUTION: Unless you are an expert computer user, do not change the settings for this program.
Certain changes can cause your computer to work incorrectly.
Entering System Setup
1. Turn on (or restart) your computer.
2. When the blue DELL logo is displayed, you must watch for the F2 prompt to appear.
3. Once the F2 prompt appears, press <F2> immediately.
NOTE: The F2 prompt indicates that the keyboard has initialized. This prompt can appear very
quickly, so you must watch for it to display, and then press <F2> . If you press <F2> before you
are prompted, this keystroke will be lost.
4. If you wait too long and the operating system logo appears, continue to wait until you see the
Microsoft Windows desktop. Then, shut down your computer and try again.
System Setup Options
NOTE: Depending on the computer and its installed devices, the items listed in this section may or
may not appear.
Table 15. General
Option Description
System Information This section lists the primary hardware features of your computer.
• System Information: Displays BIOS Version, Service Tag, Asset Tag,
Ownership Tag, Ownership Date, Manufacture Date, and the Express
Service Code.
• Memory Information: Displays Memory Installed, Memory Available,
Memory Speed, Memory Channels Mode, Memory Technology,
DIMM ASize, DIMM B Size,
• Processor Information: Displays Processor Type, Core Count,
Processor ID, Current Clock Speed, Minimum Clock Speed,
Maximum Clock Speed, Processor L2 Cache, Processor L3 Cache, HT
Capable, and 64-Bit Technology.
69
Option Description
• Device Information: Displays Primary Hard Drive, Fixed bay Device,
System eSATA Device, Dock eSATA Device, LOM MAC Address, Video
Controller, Video BIOS Version, Video Memory, Panel Type, Native
Resolution, Audio Controller, Modem Controller, Wi-Fi Device,
Cellular Device, Bluetooth Device.
Battery Information Displays the battery status and the type of AC adapter connected to the
computer
Boot Sequence Allows you to change the order in which the computer attempts to find
an operating system.
• Diskette Drive
• Internal HDD
• USB Storage Device
• CD/DVD/CD-RW Drive
• Onboard NIC
Boot List Option Allows you to change the boot list option.
• Legacy
• UEFI
Date/Time Allows you to change the date and time.
Table 16. System Configuration
Option Description
Integrated NIC Allows you to configure the integrated network controller. The options
are:
• Disabled
• Enabled
• Enabled w/PXE: This option is enabled by default.
System Management Allows you to control the system management mechanism. The options
are:
• Disabled : This option is enabled by default
• ASF 2.0
• Alert only
NOTE: This item is for non-Vpro system only.
Parallel Port Allows you to configure the parallel port on the docking station. The
options are:
• Disabled
• AT: This option is enabled by default.
• PS2
• ECP
70
Option Description
Serial Port Allows you to configure the integrated serial port. The options are:
• Disabled
• COM1: This option is enabled by default.
• COM2
• COM3
• COM4
SATA Operation Allows you to configure the internal SATA hard-drive controller. The
options are:
• Disabled
• ATA
• AHCI
• RAID On: This option is enabled by default.
Drives Allows you to configure the SATA drives on board. All drives are enabled
by default. The options are:
• SATA-0
• SATA-1
• SATA-4
• SATA-5
SMART Reporting This field controls whether hard drive errors for integrated drives are
reported during system startup. This technology is part of the SMART
(Self Monitoring Analysis and Reporting Technology) specification. This
option is disabled by default.
• Enable SMART Reporting
USB Controller This field configures the integrated USB controller. If Boot Support is
enabled, the system is allowed to boot any type of USB Mass Storage
Devices (HDD, memory key, floppy).
If USB port is enabled, device attached to this port is enabled and
available for OS.
If USB port is disabled, the OS cannot see any device attached to this
port.
• Enable Boot Support
• Enable External USB Port
NOTE: USB keyboard and mouse always work in the BIOS setup
irrespective of these settings.
Keyboard Illumination This field lets you choose the operating mode of the keyboard
illumination feature.
The keyboard brightness level can be set from 25% to 100%
• Disabled: This option is enabled by default.
• Level is 25%
71
Option Description
• Level is 50%
• Level is 75%
• Level is 100%
Miscellaneous Devices Allows you to enable or disable the following devices:
• Enable Internal Modem
• Enable Microphone
• Enable eSATA Ports
• Enable Hard Drive Free Fall Protection
• Enable Fixed Bay
• Enable Express card
• Enable Camera
NOTE: All devices are enabled by default.
You can also enable or disable Media Card.
Table 17. Video
Option Description
LCD Brightness Allows you to set the display brightness depending up on the power
source (On Battery and On AC).
NOTE: The Video setting will only be visible when a video card is installed into the system.
Table 18. Security
Option Description
Admin Password Allows you to set, change, or delete the administrator (admin) password.
NOTE: You must set the admin password before you set the system
or hard drive password. Deleting the admin password automatically
deletes the system password and the hard drive password.
NOTE: Successful password changes take effect immediately.
Default Setting: Not set
System Password Allows you to set, change or delete the system password.
NOTE: Successful password changes take effect immediately.
Default Setting: Not set
Internal HDD-0 Password Allows you to set or change the system's internal hard-disk drive.
NOTE: Successful password changes take effect immediately.
Default Setting: Not set
Strong Password Allows you to enforce the option to always set strong passwords.
Default Setting: Enable Strong Password is not selected.
72
Option Description
NOTE: If Strong Password is enabled, Admin and System passwords
must contain at least one uppercase character, one lowercase
character and be at least 8 characters long.
Password Configuration Allows you to determine the minimum and maximum length of
Administrator and System passwords.
Password Bypass Allows you to enable or disable the permission to bypass the System and
the Internal HDD password, when they are set. The options are:
• Disabled
• Reboot bypass
Default Setting: Disabled
Password Change Allows you to enable the disable permission to the System and Hard
Drive passwords when the admin password is set.
Default Setting: Allow Non-Admin Password Changes is selected
Non-Admin Setup Changes Allows you to determine whether changes to the setup options are
allowed when an Administrator Password is set. If disabled the setup
options are locked by the admin password.
TPM Security Allows you to enable the Trusted Platform Module (TPM) during POST.
Default Setting: The option is disabled.
Computrace Allows you to activate or disable the optional Computrace software The
options are:
• Deactivate
• Disable
• Activate
NOTE: The Activate and Disable options will permanently activate or
disable the feature and no further changes will be allowed
Default Setting: Deactivate
CPU XD Support Allows you to enable the Execute Disable mode of the processor.
Default Setting: Enable CPU XD Support
OROM Keyboard Access Allows you to set an option to enter the Option ROM Configuration
screens using hotkeys during boot. The options are:
• Enable
• One Time Enable
• Disable
Default Setting: Enable
Admin Setup Lockout Allows you to prevent users from entering Setup when an Administrator
password is set.
Default Setting: Enable Admin Setup Lockout is not selected.
73
Table 19. Performance
Option Description
Multi Core Support This field specifies whether the process will have one or all cores
enabled. The performance of some applications will improve with the
additional cores. This option is enabled by default.Allows you to enable
or disable multi-core support for the processor. The options are:
• All
• 1
• 2
Default Setting: All
Intel® SpeedStep™Allows you to enable or disable the Intel SpeedStep feature.
Default Setting: Enable Intel SpeedStep
C States Control Allows you to enable or disable the additional processor sleep states.
Default Setting: The option C statesis enabled.
Intel® TurboBoost™Allows you to enable or disable the Intel TurboBoost mode of the
processor.
Default Setting: Enable Intel TurboBoost
Hyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.
Default Setting: Enabled
Table 20. Power Management
Option Description
AC Behavior Allows you to enable or disable the computer from turning on
automatically when an AC adapter is connected.
Default Setting: Wake on AC is not selected.
Auto On Time Allows you to set the time at which the computer must turn on
automatically. The options are:
• Disabled
• Every Day
• Weekdays
• Select Days
Default Setting: Disabled
USB Wake Support Allows you to enable USB devices to wake the system from Standby.
NOTE: This feature is only functional when the AC power adapter is
connected. If the AC power adapter is removed during Standby, the
system setup will remove power from all of the USB ports to
conserve battery power.
• Enable USB Wake Support
• Default Setting: Enable USB Wake Support is not selected
74
Option Description
Wireless Radio Control Allows you to enable or disable the feature that automatically switches
from wired or wireless networks without depending on the physical
connection.
• Control WLAN Radio
• Control WWAN Radio
• Default Setting: Control WLAN radio or Control WWAN radio is not
selected
Wake on LAN/WLAN Allows you to enable or disable the feature that powers on the computer
from the Off state when triggered by a LAN signal.
• Disabled: This option is enabled by default
• LAN Only
• WLAN Only
• LAN or WLAN
Block Sleep This option lets you block entering to sleep (S3 state) in Operating
System environment.
Block Sleep (S3 state) - This option is disabled by default. POST
Primary Battery
Configuration
Allows you to select the charging mode for the battery. The options are:
• Standard Charge
• Express Charge
• Predominately AC use
• Auto Charge: This option is enabled by default.
• Custom Charge
If Custom Charge is selected, you can also configure Custom Charge
Start and Custom Charge Stop.
NOTE: All charging modes may not be available for all the batteries.
Battery Slice Configuration Allows you to select the type of charge for the battery. The options are:
• Standard Charge
• Express Charge : This option is enabled by default.
NOTE: Express charge may not be available for all the batteries.
Table 21. POST Behavior
Option Description
Adapter Warnings Allows you to enable or disable the system setup (BIOS) warning
messages when you use certain power adapters.
Default Setting: Enable Adapter Warnings
Keypad Allows you to choose one of two methods to enable the keypad that is
embedded in the internal keyboard.
• Fn Key Only: This option is enabled by default.
75
Option Description
• By Numlock
Mouse/Touchpad Allows you to define how the system handles mouse and touch pad
input. The options are:
• Serial Mouse
• PS2 Mouse
• Toushpad/PS-2 Mouse: This option is enabled by default.
Numlock Enable Allows you to enable the Numlock option when the computer boots.
Default Setting: Enable Network
Fn Key Emulation Allows you to set the option where the <Scroll Lock> key is used to
simulate the <Fn> key feature.
Default Setting: Enable Fn Key Emulation
POST HotKeys Allows you enable the sign-on screen message display indicating the
keystroke sequence to access the System Setup option menu.
Default Setting: Enable F12 Boot Option Menu
Table 22. Virtualization Support
Option Description
Virtualization Allows you to enable or disable the Intel Virtualization Technology.
Default Setting: Enable Intel Virtualization Technology
VT for Direct I/O Enables or disables the Virtual Machine Monitor (VMM) from utilizing the
additional hardware capabilities provided by Intel® Virtualization
technology for direct I/O.
Enable VT for Direct I/O — This option is enabled by default.
Trusted Execution This option specifies whether a Measured Virtual Machine Monitor
(MVMM) can utilize the additional hardware capabilities provided by Intel
Trusted Execution Technology. The TPM virtualization Technology, and
Virtualization technology for direct I/O must be enabled to use this
feature.
Trusted Execution — disabled by default.
Table 23. Wireless
Option Description
Wireless Switch Allows to set the wireless devices that can be controlled by the wireless
switch. The options are:
• WWAN
• WLAN
• Bluetooth
All the options are enabled by default.
Wireless Device Enable Allows you to enable or disable the internal wireless devices.
76
Option Description
• WWAN
• WLAN
• Bluetooth
All the options are enabled by default.
Table 24. Maintenance
Option Description
Service Tag Displays the Service Tag of your computer.
Asset Tag Allows you to create a system asset tag if an asset tag is not already set.
This option is not set by default.
Table 25. System Logs
Option Description
BIOS Events Allows you to view and clear the System Setup (BIOS) POST events.
77
78
7
Diagnostics
If you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for
technical assistance. The purpose of running diagnostics is to test your computer's hardware without
requiring additional equipment or risking data loss. If you are unable to fix the problem yourself, service
and support personnel can use the diagnostics results to help you solve the problem.
Diagnostics
Table 26. Device Status Lights
Turns on when you turn on the computer and
blinks when the computer is in a power
management mode.
Turns on when the computer reads or writes data.
Turns on steadily or blinks to indicate battery
charge status.
Turns on when wireless networking is enabled.
If the computer is connected to an electrical outlet, the battery light operates as follows:
Table 27. Battery Status Lights
Alternately blinking amber light and blue light An unauthenticated or unsupported non-Dell AC
adapter is attached to your laptop.
Alternately blinking amber light with steady blue
light
Temporary battery failure with AC adapter present.
Constantly blinking amber light Fatal battery failure with AC adapter present.
Light off Battery in full charge mode with AC adapter
present.
Solid white light on Battery in charge mode with AC adapter present.
The lights located above the keyboard indicate the following:
79
Table 28. Keyboard Status Lights
Turns on when the numeric keypad is enabled.
Turns on when the Caps Lock function is enabled.
Turns on when the Scroll Lock function is enabled.
80
8
Contacting Dell
NOTE: If you do not have an active Internet connection, you can find contact information on your
purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides several online and telephone-based support and service options. Availability varies by
country and product, and some services may not be available in your area. To contact Dell for sales,
technical support, or customer service issues:
1. Visit dell.com/support
2. Select your support category.
3. Verify your country or region in the Choose a Country/Region drop-down menu at the top of page.
4. Select the appropriate service or support link based on your need.
81