Dell EMC PowerEdge T340 Installation and Service Manual
About this document
Dell EMC PowerEdge T340 system overview
PowerEdge T340 initial system setup and configuration
PowerEdge T340 Pre-operating system management applications
Installing and removing system components
PowerEdge T340 jumpers and connectors
Technical specifications
System diagnostics and indicator codes
Getting help
Documentation resources

DELL T340 User Manual

Displayed below is the user manual for T340 by DELL which is a product in the Servers category. This manual has pages.

Related Manuals

DELL T340 Manual

Dell EMC PowerEdge T340

Installation and Service Manual

Regulatory Model: E60S

Regulatory Type: E60S001

June 2020

Rev. A06

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the

problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

subsidiaries. Other trademarks may be trademarks of their respective owners.

1 About this document.....................................................................................................................7

2 Dell EMC PowerEdge T340 system overview.................................................................................. 8

Front view of the system..................................................................................................................................................... 9

Rear view of the system...................................................................................................................................................... 11

Inside the system..................................................................................................................................................................12

Locating the information tag of your system................................................................................................................... 14

System information label.....................................................................................................................................................14

3 PowerEdge T340 initial system setup and configuration................................................................. 17

Setting up your system........................................................................................................................................................17

iDRAC configuration.............................................................................................................................................................17

Options to set up iDRAC IP address............................................................................................................................ 17

Log in to iDRAC.............................................................................................................................................................. 17

Options to install the operating system.............................................................................................................................18

Methods to download firmware and drivers...............................................................................................................18

Downloading drivers and firmware...............................................................................................................................19

4 PowerEdge T340 Pre-operating system management applications................................................. 20

Options to manage the pre-operating system applications...........................................................................................20

System Setup.......................................................................................................................................................................20

Viewing System Setup..................................................................................................................................................20

System Setup details..................................................................................................................................................... 21

System BIOS...................................................................................................................................................................21

iDRAC Settings utility.................................................................................................................................................... 37

Device Settings.............................................................................................................................................................. 37

Dell Lifecycle Controller...................................................................................................................................................... 37

Embedded system management................................................................................................................................. 37

Boot Manager...................................................................................................................................................................... 38

Viewing Boot Manager..................................................................................................................................................38

Boot Manager main menu............................................................................................................................................ 38

One-shot UEFI boot menu........................................................................................................................................... 38

System Utilities.............................................................................................................................................................. 38

PXE boot.............................................................................................................................................................................. 38

5 Installing and removing system components.................................................................................40

Safety instructions.............................................................................................................................................................. 40

Before working inside your system................................................................................................................................... 40

After working inside your system......................................................................................................................................40

Recommended tools........................................................................................................................................................... 40

Front bezel............................................................................................................................................................................ 41

Removing the front bezel..............................................................................................................................................41

Installing the front bezel................................................................................................................................................ 41

System feet..........................................................................................................................................................................42

Contents

Contents 3

Removing the system feet........................................................................................................................................... 42

Installing the system feet..............................................................................................................................................43

Caster wheels – optional....................................................................................................................................................44

Removing caster wheels...............................................................................................................................................44

Installing caster wheels.................................................................................................................................................45

System cover.......................................................................................................................................................................46

Removing the system cover........................................................................................................................................ 46

Installing the system cover........................................................................................................................................... 47

Air shroud............................................................................................................................................................................. 48

Removing the air shroud...............................................................................................................................................48

Installing the air shroud................................................................................................................................................. 49

Intrusion switch................................................................................................................................................................... 50

Removing the intrusion switch.................................................................................................................................... 50

Installing the intrusion switch........................................................................................................................................51

Drives.................................................................................................................................................................................... 52

Removing a drive blank.................................................................................................................................................52

Installing a drive blank................................................................................................................................................... 52

Removing a drive carrier...............................................................................................................................................53

Installing the drive carrier............................................................................................................................................. 54

Removing the drive from the drive carrier.................................................................................................................55

Installing the drive into the drive carrier..................................................................................................................... 56

Removing a 2.5-inch drive from the 3.5-inch drive adapter....................................................................................57

Installing a 2.5-inch drive into the 3.5-inch drive adapter........................................................................................58

Removing a 3.5-inch drive adapter from a 3.5-inch drive carrier........................................................................... 59

Installing a 3.5-inch adapter into a 3.5-inch drive carrier.........................................................................................60

Optical drive and tape drives.............................................................................................................................................. 61

Removing the optical or tape drive blank....................................................................................................................61

Installing the optical or tape drive blank..................................................................................................................... 62

Removing the optical drive...........................................................................................................................................62

Installing the optical drive............................................................................................................................................. 63

Removing the tape drive.............................................................................................................................................. 64

Installing the tape drive.................................................................................................................................................65

Drive backplane................................................................................................................................................................... 66

Drive backplane details................................................................................................................................................. 66

Removing the drive backplane ....................................................................................................................................67

Installing the drive backplane....................................................................................................................................... 68

Backplane cable routing......................................................................................................................................................69

Four-slot drive blank............................................................................................................................................................70

Removing a four-slot drive blank.................................................................................................................................70

Installing a four-slot drive blank.................................................................................................................................... 71

System memory...................................................................................................................................................................72

System memory guidelines........................................................................................................................................... 72

General memory module installation guidelines..........................................................................................................73

Removing a memory module........................................................................................................................................73

Installing a memory module.......................................................................................................................................... 74

Cooling fan............................................................................................................................................................................75

Removing the internal cooling fan............................................................................................................................... 75

Installing the internal cooling fan..................................................................................................................................76

Optional internal USB memory key....................................................................................................................................77

Replacing the optional internal USB memory key......................................................................................................77

4Contents

Expansion cards ..................................................................................................................................................................78

Expansion card guidelines.............................................................................................................................................78

Removing an expansion card........................................................................................................................................78

Installing an expansion card..........................................................................................................................................80

M.2 SSD module...................................................................................................................................................................81

Removing the M.2 SSD module................................................................................................................................... 81

Installing the M.2 SSD module..................................................................................................................................... 82

Optional IDSDM or vFlash module.................................................................................................................................... 83

Removing the optional IDSDM or vFlash card...........................................................................................................83

Installing optional IDSDM or vFlash card.................................................................................................................... 84

Removing the MicroSD card........................................................................................................................................84

Installing the MicroSD card.......................................................................................................................................... 85

Processor and heat sink..................................................................................................................................................... 86

Removing the heat sink................................................................................................................................................ 86

Removing the processor...............................................................................................................................................87

Installing the processor................................................................................................................................................. 88

Installing the heat sink...................................................................................................................................................89

Power supply unit................................................................................................................................................................90

Removing the power supply unit blank.......................................................................................................................90

Installing the power supply unit blank.......................................................................................................................... 91

Removing a redundant AC power supply unit............................................................................................................92

Installing a redundant AC power supply unit..............................................................................................................92

Removing a cabled power supply unit........................................................................................................................ 93

Installing a cabled power supply unit...........................................................................................................................94

Power interposer board......................................................................................................................................................95

Removing the power interposer board.......................................................................................................................95

Installing the power interposer board......................................................................................................................... 96

System battery ................................................................................................................................................................... 97

Replacing the system battery...................................................................................................................................... 97

System board.......................................................................................................................................................................98

Removing the system board........................................................................................................................................ 98

Installing the system board......................................................................................................................................... 100

Trusted Platform Module..................................................................................................................................................102

Upgrading the Trusted Platform Module..................................................................................................................102

Initializing TPM for BitLocker users...........................................................................................................................103

Initializing the TPM 1.2 for TXT users........................................................................................................................103

Initializing the TPM 2.0 for TXT users.......................................................................................................................103

Control panel...................................................................................................................................................................... 104

Removing the control panel assembly.......................................................................................................................104

Installing the control panel assembly......................................................................................................................... 104

6 PowerEdge T340 jumpers and connectors .................................................................................. 106

System board jumpers and connectors.......................................................................................................................... 106

System board jumper settings..........................................................................................................................................107

Disabling forgotten password...........................................................................................................................................107

7 Technical specifications.............................................................................................................109

Chassis dimensions............................................................................................................................................................109

System weight.................................................................................................................................................................... 110

Contents 5

Processor specifications....................................................................................................................................................110

Supported operating systems...........................................................................................................................................110

PSU specifications..............................................................................................................................................................110

Cooling fan specifications...................................................................................................................................................111

System battery specifications............................................................................................................................................111

Expansion card specifications............................................................................................................................................111

Memory specifications........................................................................................................................................................111

Storage controller specifications...................................................................................................................................... 112

Drive specifications.............................................................................................................................................................112

Drives..............................................................................................................................................................................112

Optical drives.................................................................................................................................................................112

Tape drives.................................................................................................................................................................... 112

Ports and connectors specifications................................................................................................................................112

USB ports specifications..............................................................................................................................................112

NIC ports specifications...............................................................................................................................................113

Serial connector specifications....................................................................................................................................113

VGA ports specification............................................................................................................................................... 113

IDSDM module...............................................................................................................................................................113

Video specifications............................................................................................................................................................113

Environmental specifications.............................................................................................................................................114

Standard operating temperature................................................................................................................................ 115

Expanded operating temperature...............................................................................................................................115

Particulate and gaseous contamination specifications............................................................................................ 116

8 System diagnostics and indicator codes ......................................................................................117

System health and system ID indicator codes................................................................................................................ 117

iDRAC Direct LED indicator codes....................................................................................................................................117

NIC indicator codes............................................................................................................................................................ 118

Non-redundant cabled power supply unit indicator codes............................................................................................118

Power supply unit indicator codes....................................................................................................................................119

Drive indicator codes.........................................................................................................................................................120

PowerEdge T340 system diagnostics..............................................................................................................................121

Dell Embedded System Diagnostics........................................................................................................................... 121

9 Getting help............................................................................................................................. 123

Recycling or End-of-Life service information.................................................................................................................123

Contacting Dell...................................................................................................................................................................123

Accessing system information by using QRL................................................................................................................. 123

Quick Resource Locator for Dell EMC PowerEdge T340 system......................................................................... 124

Receiving automated support with SupportAssist ....................................................................................................... 124

10 Documentation resources.........................................................................................................125

6Contents

About this document

This document provides an overview about the system, information about installing and replacing components, technical specifications,

diagnostic tools, and guidelines to be followed while installing certain components.

About this document 7

Dell EMC PowerEdge T340 system overview

The Dell EMC PowerEdge T340 system is a tower server that supports:

• One Intel Xeon, Core i3, Pentium, or Celeron processor

• Four DIMM slots

• Redundant and cabled AC power supply units

• Up to eight 3.5-inch or four 3.5-inch SAS, SATA drives, or SSDs.

For more information, see the Technical specifications section.

NOTE: All instances of SAS, SATA drives, and SSDs are referred to as drives in this document, unless specified

otherwise.

Topics:

•Front view of the system

•Rear view of the system

•Inside the system

•Locating the information tag of your system

•System information label

8 Dell EMC PowerEdge T340 system overview

Front view of the system

Figure 1. Front view of 8 x 3.5-inch drive system

1. Power button 2. Information tag

3. System health and system ID indicator 4. USB 3.0 port

5. iDRAC direct micro USB port 6. Optical drive (optional)

7. Drive (8)

Dell EMC PowerEdge T340 system overview 9

Figure 2. Front view of 4 x 3.5-inch drive system

1. Power button 2. Information tag

3. System health and system ID indicator 4. USB 3.0 port

5. iDRAC direct micro USB port 6. Optical drive (optional)

7. Drive (4) 8. Four-slot drive blank

For more information about the ports, see the Ports and connectors specifications section.

10 Dell EMC PowerEdge T340 system overview

Rear view of the system

Figure 3. Rear view of 8 x 3.5-inch drive system

1. Power supply unit (PSU 1) 2. Power supply unit (PSU 2)

3. USB 2.0 port (4) 4. System Identification button

5. USB 3.0 port (2) 6. iDRAC dedicated NIC port

7. VGA port 8. Serial port

9. NIC port (Gb1) 10. NIC port (Gb2)

11. PCIe expansion card slots (4)

Dell EMC PowerEdge T340 system overview 11

Figure 4. Rear view of 4 x 3.5-inch drive system

1. Cabled power supply unit (PSU) 2. USB 2.0 port (4)

3. System identification button 4. USB 3.0 port (2)

5. iDRAC dedicated NIC port 6. VGA port

7. Serial port 8. NIC port (Gb1)

9. NIC port (Gb2) 10. PCIe expansion card slots (4)

NOTE: For more information about the ports and connectors, see the Ports and connectors specifications section.

Inside the system

NOTE: Components that are hot swappable are marked orange and touch points on the components are marked blue.

12 Dell EMC PowerEdge T340 system overview

Figure 5. Inside the system with cabled power supply unit (PSU)

1. Optical drive or tape drive 2. Power supply unit (cabled)

3. PCIe Expansion card latch (4) 4. PCIe Expansion card slots (4)

5. Intrusion switch 6. Air shroud

7. Drive backplane

Figure 6. Inside the system with redundant power supply unit (PSU)

1. Optical drive or tape drive 2. Power interposer board

3. PCIe Expansion card latch (4) 4. PCIe Expansion card slots (4)

5. Intrusion switch 6. Fan

7. Memory module socket (4) 8. Processor and heat sink

9. System board 10. Drive backplane

Dell EMC PowerEdge T340 system overview 13

Locating the information tag of your system

Your system is identified by a unique Express Service Code and Service Tag number. You can view the Express Service Code and Service

Tag by pulling out the information tag located on the front of the system. Alternatively, the information may be on the Mini Enterprise

Service Tag (MEST) label on the chassis, on the rear of the system. This information is used by Dell to route support calls to the

appropriate personnel.

Figure 7. Locating Service Tag of your system

1. Information tag (top view) 2. Information tag (back view)

3. OpenManage Mobile (OMM) label 4. iDRAC MAC address and iDRAC secure password label

5. Service Tag, Express Service Code, QRL label

System information label

PowerEdge T340 – System information label

Figure 8. Mechanical overview

14 Dell EMC PowerEdge T340 system overview

Figure 9. Electrical overview

Figure 10. Icon legend

Figure 11. DVD and BOSS installation

Figure 12. CPU installation

Dell EMC PowerEdge T340 system overview 15

Figure 13. Heat sink installation

Figure 14. Internal cooling fan installation

Figure 15. Memory population

Figure 16. Quick resource locator

16 Dell EMC PowerEdge T340 system overview

PowerEdge T340 initial system setup and

configuration

Setting up your system

Perform the following steps to set up your system:

Steps

1. Unpack the system.

2. Connect the peripherals to the system.

3. Connect the system to its electrical outlet.

4. Power on the system by pressing the power button or by using iDRAC.

5. Power on the attached peripherals.

For more information about setting up your system, see the Getting Started Guide that shipped with your system.

iDRAC configuration

The Integrated Dell Remote Access Controller (iDRAC) is designed to make system administrators more productive and improve the

overall availability of Dell systems. iDRAC alerts administrators about system issues and enables them to perform remote system

management. This reduces the need for physical access to the system.

Options to set up iDRAC IP address

To enable communication between your system and iDRAC, you must first configure the network settings based on your network

infrastructure.

NOTE: For static IP configuration, you must request for it at the time of purchase.

This option is set to DHCP by Default. You can set up the IP address by using one of the following interfaces:

Interfaces Document/Section

iDRAC Settings

utility

Dell Integrated Dell Remote Access Controller User's Guide at www.dell.com/poweredgemanuals

Dell Deployment

Toolkit

Dell Deployment Toolkit User’s Guide at www.dell.com/openmanagemanuals > OpenManage Deployment Toolkit

Dell Lifecycle

Controller

Dell Lifecycle Controller User’s Guide at www.dell.com/poweredgemanuals

NOTE: To access iDRAC, ensure that you connect the ethernet cable to the iDRAC9 dedicated network port. You can

also access iDRAC through the shared LOM mode, if you have opted for a system that has the shared LOM mode

enabled.

You can log in to iDRAC as:

• iDRAC user

• Microsoft Active Directory user

• Lightweight Directory Access Protocol (LDAP) user

PowerEdge T340 initial system setup and configuration 17

If you have opted for secure default access to iDRAC, you must use the iDRAC secure default password available on the system

Information tag. If you have not opted for secure default access to iDRAC, then use the default user name and password –root and

calvin. You can also log in by using your Single Sign-On or Smart Card.

NOTE: You must have the iDRAC credentials to log in to iDRAC.

NOTE: Ensure that you change the default user name and password after setting up the iDRAC IP address.

For more information about logging in to the iDRAC and iDRAC licenses, see the latest Integrated Dell Remote Access Controller User's

Guide at www.dell.com/poweredgemanuals.

You can also access iDRAC by using RACADM. For more information, see the RACADM Command Line Interface Reference Guide at

www.dell.com/poweredgemanuals.

Options to install the operating system

If the system is shipped without an operating system, install a supported operating system by using one of the following resources:

Table 1. Resources to install the operating system

Resources Location

iDRAC www.dell.com/idracmanuals

Lifecycle Controller www.dell.com/idracmanuals > Lifecycle Controller

OpenManage Deployment Toolkit www.dell.com/openmanagemanuals > OpenManage Deployment

Toolkit

Dell certified VMware ESXi www.dell.com/virtualizationsolutions

Installation and How-to videos for supported operating systems on

PowerEdge systems

Supported Operating Systems for Dell EMC PowerEdge systems

Methods to download firmware and drivers

You can download the firmware and drivers by using any of the following methods:

Table 2. Firmware and drivers

Methods Location

From the Dell EMC support site www.dell.com/support/home

Using Dell Remote Access Controller Lifecycle Controller (iDRAC

with LC)

www.dell.com/idracmanuals

Using Dell Repository Manager (DRM) www.dell.com/openmanagemanuals > Repository Manager

Using Dell OpenManage Essentials www.dell.com/openmanagemanuals > OpenManage Essentials

Using Dell OpenManage Enterprise www.dell.com/openmanagemanuals > OpenManage Enterprise

Using Dell Server Update Utility (SUU) www.dell.com/openmanagemanuals > Server Update Utility

Using Dell OpenManage Deployment Toolkit (DTK) www.dell.com/openmanagemanuals > OpenManage Deployment

Toolkit

Using iDRAC virtual media www.dell.com/idracmanuals

18 PowerEdge T340 initial system setup and configuration

Downloading drivers and firmware

Dell EMC recommends that you download and install the latest BIOS, drivers, and systems management firmware on your system.

Prerequisites

Ensure that you clear the web browser cache before downloading the drivers and firmware.

Steps

1. Go to www.dell.com/support/home.

2. In the Drivers & Downloads section, type the Service Tag of your system in the Enter a Service Tag or product ID box, and then

click Submit.

NOTE: If you do not have the Service Tag, select Detect Product to allow the system to automatically detect the

Service Tag, or click View products, and navigate to your product.

3. Click Drivers & Downloads.

The drivers that are applicable to your system are displayed.

4. Download the drivers to a USB drive, CD, or DVD.

PowerEdge T340 initial system setup and configuration 19

PowerEdge T340 Pre-operating system

management applications

You can manage basic settings and features of a system without booting to the operating system by using the system firmware.

Topics:

•Options to manage the pre-operating system applications

•System Setup

•Dell Lifecycle Controller

•Boot Manager

•PXE boot

Options to manage the pre-operating system

applications

Your system has the following options to manage the pre-operating system applications:

• System Setup

• Dell Lifecycle Controller

• Boot Manager

• Preboot Execution Environment (PXE)

System Setup

By using the System Setup screen, you can configure the BIOS settings, iDRAC settings, and device settings of your system.

NOTE: Help text for the selected field is displayed in the graphical browser by default. To view the help text in the text

browser, press F1.

You can access system setup by one of the following:

• Standard graphical browser—The browser is enabled by default.

• Text browser—The browser is enabled by using Console Redirection.

Viewing System Setup

To view the System Setup screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

20 PowerEdge T340 Pre-operating system management applications

System Setup details

The System Setup Main Menu screen details are explained as follows:

Option Description

System BIOS Enables you to configure BIOS settings.

iDRAC Settings Enables you to configure the iDRAC settings.

The iDRAC settings utility is an interface to set up and configure the iDRAC parameters by using UEFI (Unified

Extensible Firmware Interface). You can enable or disable various iDRAC parameters by using the iDRAC settings

utility. For more information about this utility, see Integrated Dell Remote Access Controller User’s Guide at

www.dell.com/poweredgemanuals.

Device Settings Enables you to configure device settings.

System BIOS

You can use the System BIOS screen to edit specific functions such as boot order, system password, setup password, set the SATA

mode, and enable or disable USB ports.

Viewing System BIOS

To view the System BIOS screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If the operating system begins to load before you press F2, wait for the system to finish booting, and then

restart the system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

System BIOS Settings details

About this task

The System BIOS Settings screen details are explained as follows:

Option Description

System

Information

Specifies information about the system such as the system model name, BIOS version, and Service Tag.

Memory Settings Specifies information and options related to the installed memory.

Processor

Settings

Specifies information and options related to the processor such as speed and cache size.

SATA Settings Specifies options to enable or disable the integrated SATA controller and ports.

Boot Settings Specifies options to specify the Boot mode (BIOS or UEFI). Enables you to modify UEFI and BIOS boot settings.

Network Settings Specifies options to manage the UEFI network settings and boot protocols.

Legacy network settings are managed from the Device Settings menu.

Integrated Devices Specifies options to manage integrated device controllers and ports, specifies related features and options.

Serial

Communication

Specifies options to manage the serial ports, its related features and options.

PowerEdge T340 Pre-operating system management applications 21

Option Description

System Profile

Settings

Specifies options to change the processor power management settings, memory frequency.

System Security Specifies options to configure the system security settings, such as system password, setup password, Trusted

Platform Module (TPM) security, and UEFI secure boot. It also manages the power button on the system.

Redundant OS

Control

Sets the redundant OS info for redundant OS control.

Miscellaneous

Settings

Specifies options to change the system date and time.

System Information

You can use the System Information screen to view system properties such as Service Tag, system model name, and BIOS version.

Viewing System Information

To view the System Information screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Information.

System Information details

About this task

The System Information screen details are explained as follows:

Option Description

System Model

Name

Specifies the system model name.

System BIOS

Version

Specifies the BIOS version installed on the system.

System

Management

Engine Version

Specifies the current version of the Management Engine firmware.

System Service

Tag

Specifies the system Service Tag.

System

Manufacturer

Specifies the name of the system manufacturer.

System

Manufacturer

Contact

Information

Specifies the contact information of the system manufacturer.

System CPLD

Version

Specifies the current version of the system complex programmable logic device (CPLD) firmware.

22 PowerEdge T340 Pre-operating system management applications

Option Description

UEFI Compliance

Version

Specifies the UEFI compliance level of the system firmware.

Memory Settings

You can use the Memory Settings screen to view all the memory settings and enable or disable specific memory functions, such as

system memory testing and node interleaving.

Viewing Memory Settings

To view the Memory Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If the operating system begins to load before you press F2, wait for the system to finish booting, and then

restart the system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Memory Settings.

Memory Settings details

About this task

The Memory Settings screen details are explained as follows:

Option Description

System Memory

Size

Specifies the memory size in the system.

System Memory

Type

Specifies the type of memory installed in the system.

System Memory

Speed

Specifies the system memory speed.

System Memory

Voltage

Specifies the system memory voltage.

Video Memory Specifies the amount of video memory.

System Memory

Testing

Specifies whether the system memory tests are run during system boot. Options are Enabled and Disabled. This

option is set to Disabled by default.

Memory Operating

Mode

Specifies the memory operating mode. This option is set to Optimizer Mode by default.

NOTE: The Memory Operating Mode option can have different default and available options based

on the memory configuration of your system.

Current State of

Memory Operating

Mode

Specifies the current state of the memory operating mode.

PowerEdge T340 Pre-operating system management applications 23

Processor Settings

You can use the Processor Settings screen to view the processor settings, and perform specific functions such as enabling virtualization

technology, hardware prefetcher, and logical processor idling.

Viewing Processor Settings

To view the Processor Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Processor Settings.

Processor Settings details

About this task

The Processor Settings screen details are explained as follows:

Option Description

Logical Processor Enables or disables the logical processors and displays the number of logical processors. If this option is set to

Enabled, the BIOS displays all the logical processors. If this option is set to Disabled, the BIOS displays only one

logical processor per core. This option is set to Enabled by default.

Virtualization

Technology

Enables or disables the virtualization technology for the processor. This option is set to Enabled by default.

Adjacent Cache

Line Prefetch

Optimizes the system for applications that need high utilization of sequential memory access. This option is set to

Enabled by default. You can disable this option for applications that need high utilization of random memory

access.

Hardware

Prefetcher

Enables or disables the hardware prefetcher. This option is set to Enabled by default.

Logical Processor

Idling

Enables you to improve the energy efficiency of a system. It uses the operating system core parking algorithm and

parks some of the logical processors in the system which in turn allows the corresponding processor cores to

transition into a lower power idle state. This option can only be enabled if the operating system supports it. It is set

to Disabled by default.

x2APIC Mode Enables or disables the x2APIC mode. This option is set to Disabled by default.

Number of Cores

per Processor

Controls the number of enabled cores in each processor. This option is set to All by default.

Processor Core

Speed

Specifies the maximum core frequency of the processor.

Processor 1 The following settings are displayed for each processor installed in the system:

Option Description

Family-Model-

Stepping

Specifies the family, model, and stepping of the processor as defined by Intel.

Brand Specifies the brand name.

Level 2 Cache Specifies the total L2 cache.

24 PowerEdge T340 Pre-operating system management applications

Option Description

Level 3 Cache Specifies the total L3 cache.

Number of Cores Specifies the number of cores per processor.

Microcode Specifies the microcode.

SATA Settings

You can use the SATA Settings screen to view the SATA settings of SATA devices and enable SATA on your system.

Viewing SATA Settings

To view the SATA Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click SATA Settings.

SATA Settings details

About this task

The SATA Settings screen details are explained as follows:

Option Description

Embedded SATA Enables the embedded SATA option to be set to Off, AHCI, or RAID modes. This option is set to AHCI Mode by

default.

Security Freeze

Lock

Sends Security Freeze Lock command to the embedded SATA drives during POST. This option is applicable only

for AHCI Mode. This option is set to Enabled by default.

Write Cache Enables or disables the command for the embedded SATA drives during POST. This option is set to Disabled by

default.

Port n Sets the drive type of the selected device.

For AHCI Mode or RAID Mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the drive. This field is undefined for removable media

devices such as optical drives.

PowerEdge T340 Pre-operating system management applications 25

Boot Settings

You can use the Boot Settings screen to set the boot mode to either BIOS or UEFI. It also enables you to specify the boot order.

•UEFI: The Unified Extensible Firmware Interface (UEFI) is a new interface between operating systems and platform firmware. The

interface consists of data tables with platform related information, boot and runtime service calls that are available to the operating

system and its loader. The following benefits are available when the Boot Mode is set to UEFI:

○Support for drive partitions larger than 2 TB.

○Enhanced security (e.g., UEFI Secure Boot).

○Faster boot time.

•BIOS: The BIOS Boot Mode is the legacy boot mode. It is maintained for backward compatibility.

Viewing Boot Settings

To view the Boot Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Boot Settings.

Boot Settings details

About this task

The Boot Settings screen details are explained as follows:

Option Description

Boot Mode Enables you to set the boot mode of the system.

CAUTION: Switching the boot mode may prevent the system from booting if the operating system

is not installed in the same boot mode.

If the operating system supports UEFI, you can set this option to UEFI. Setting this field to BIOS allows

compatibility with non-UEFI operating systems. This option is set to UEFI by default.

NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu.

Boot Sequence

Retry

Enables or disables the Boot Sequence Retry feature. If this option is set to Enabled and the system fails to

boot, the system re-attempts the boot sequence after 30 seconds. This option is set to Enabled by default.

Hard-Disk Failover Specifies the drive that is booted in the event of a drive failure. The devices are selected in the Hard-Disk Drive

Sequence on the Boot Option Setting menu. When this option is set to Disabled, only the first drive in the list

is attempted to boot. When this option is set to Enabled, all drives are attempted to boot in the order selected in

the Hard-Disk Drive Sequence. This option is not enabled for UEFI Boot Mode. This option is set to Disabled

by default.

Generic USB boot Enables or disables generic USB boot. This option is set to Disabled by default.

Hard-disk Drive

Placeholder

Enables or disables Hard-disk Drive Placeholder.

UEFI Boot

Settings

Enables or disables UEFI Boot options.

The Boot options include IPv4 PXE and IPv6 PXE. This option is set to IPv4 by default.

NOTE: This option is enabled only if the boot mode is UEFI.

26 PowerEdge T340 Pre-operating system management applications

Option Description

UEFI Boot

Sequence

Enables you to change the boot device order.

Boot Options

Enable/Disable

Enables you to select the enabled or disabled boot devices.

Network Settings

You can use the Network Settings screen to modify UEFI PXE, iSCSI, and HTTP boot settings. The network settings option is available

only in the UEFI mode.

NOTE: BIOS does not control network settings in the BIOS mode. For the BIOS boot mode, the optional Boot ROM of

the network controllers handles the network settings.

Viewing Network Settings

To view the Network Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Network Settings.

Network Settings screen details

The Network Settings screen details are explained as follows:

About this task

Option Description

PXE Device n (n =

1 to 4)

Enables or disables the device. When enabled, a UEFI PXE boot option is created for the device.

PXE Device n

Settings(n = 1 to

Enables you to control the configuration of the PXE device.

HTTP Device n (n

= 1 to 4)

Enables or disables the device. When enabled, a UEFI HTTP boot option is created for the device.

HTTP Device n

Settings (n = 1 to

Enables you to control the configuration of the HTTP device.

UEFI iSCSI

Settings

Enables you to control the configuration of the iSCSI device.

Table 3. UEFI iSCSI Settings screen details

Option Description

iSCSI Initiator Name Specifies the name of the iSCSI initiator in IQN

format.

iSCSI Device1 Enables or disables the iSCSI device. When enabled,

a UEFI boot option is created for the iSCSI device

automatically. This is set to Enabled by default.

PowerEdge T340 Pre-operating system management applications 27

Option Description

Table 3. UEFI iSCSI Settings screen details(continued)

Option Description

iSCSI Device1 Settings Enables you to control the configuration of the iSCSI

device.

Integrated Devices

You can use the Integrated Devices screen to view and configure the settings of all integrated devices including the video controller,

integrated RAID controller, and the USB ports.

Viewing Integrated Devices

To view the Integrated Devices screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Integrated Devices.

Integrated Devices details

About this task

The Integrated Devices screen details are explained as follows:

Option Description

User Accessible

USB Ports

Configures the user accessible USB ports. Selecting Only Back Ports On disables the front USB ports; selecting

All Ports Off disables all front and back USB ports;

The USB keyboard and mouse still function in certain USB ports during the boot process, depending on the

selection. After the boot process is complete, the USB ports will be enabled or disabled as per the setting.

NOTE: Selecting Only Back Ports On and All Ports Off disables the USB management port and also

restricts access to the iDRAC features.

Internal USB Port Enables or disables the internal USB port. This option is set to On or Off. This option is set to On by default.

iDRAC Direct USB

Port

The iDRAC Direct USB port is managed by iDRAC exclusively with no host visibility. This option is set to ON or

OFF. When set to OFF, iDRAC does not detect any USB devices installed in this managed port. This option is set

to On by default.

Embedded NIC1

and NIC2

NOTE: The Embedded NIC1 and NIC2 options are only available on systems that do not have

Integrated Network Card 1.

Enables or disables the Embedded NIC1 and NIC2 options. If set to Disabled, the NIC may still be available for

shared network access by the embedded management controller. The embedded NIC1 and NIC2 options are only

available on systems that do not have Network Daughter Cards (NDCs). The Embedded NIC1 and NIC2 option is

mutually exclusive with the Integrated Network Card 1 option. Configure the Embedded NIC1 and NIC2 option by

using the NIC management utilities of the system.

28 PowerEdge T340 Pre-operating system management applications

Option Description

I/OAT DMA

Engine

Enables or disables the I/O Acceleration Technology (I/OAT) option. I/OAT is a set of DMA features designed to

accelerate network traffic and lower CPU utilization. Enable only if the hardware and software support the

feature.

Embedded Video

Controller

Enables or disables the use of Embedded Video Controller as the primary display. When set to Enabled, the

Embedded Video Controller will be the primary display even if add-in graphic cards are installed. When set to

Disabled, an add-in graphics card will be used as the primary display. BIOS will output displays to both the primary

add-in video and the embedded video during POST and pre-boot environment. The embedded video will then be

disabled right before the operating system boots. This option is set to Enabled by default.

NOTE: When there are multiple add-in graphic cards installed in the system, the first card

discovered during PCI enumeration is selected as the primary video. You might have to re-arrange

the cards in the slots in order to control which card is the primary video.

Current State of

Embedded Video

Controller

Displays the current state of the embedded video controller. The Current State of Embedded Video

Controller option is a read-only field. If the Embedded Video Controller is the only display capability in the system

(that is, no add-in graphics card is installed), then the Embedded Video Controller is automatically used as the

primary display even if the Embedded Video Controller setting is set to Enabled.

OS Watchdog

Timer

If your system stops responding, this watchdog timer aids in the recovery of your operating system. When this

option is set to Enabled, the operating system initializes the timer. When this option is set to Disabled (the

default), the timer does not have any effect on the system.

Memory Mapped

I/O above 4 GB

Enables or disables the support for the PCIe devices that need large amounts of memory. Enable this option only

for 64-bit operating systems. This option is set to Enabled by default.

Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement feature controls the

configuration of the PCIe cards installed in the specified slot. Slots must be disabled only when the installed

peripheral card prevents booting into the operating system or causes delays in system startup. If the slot is

disabled, both the Option ROM and UEFI drivers are disabled. Only slots that are present on the system will be

available for control.

Table 4. Slot Disablement

Option Description

Slot 1 Enables or disables or only the boot driver is disabled

for the PCIe slot 1. This option is set to Enabled by

default.

Slot 2 Enables or disables or only the boot driver is disabled

for the PCIe slot 2. This option is set to Enabled by

default.

Slot 3 Enables or disables or only the boot driver is disabled

for the PCIe slot 3. This option is set to Enabled by

default.

Slot 4 Enables or disables or only the boot driver is disabled

for the PCIe slot 4. This option is set to Enabled by

default.

Serial Communication

You can use the Serial Communication screen to view the properties of the serial communication port.

Viewing Serial Communication

To view the Serial Communication screen, perform the following steps:

Steps

1. Power on, or restart your system.

PowerEdge T340 Pre-operating system management applications 29

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Serial Communication.

Serial Communication details

About this task

The Serial Communication screen details are explained as follows:

Option Description

Serial

Communication

Selects serial communication devices (Serial Device 1 and Serial Device 2) in BIOS. BIOS console redirection can

also be enabled, and the port address can be specified. This option is set to Auto by default.

Serial Port

Address

Enables you to set the port address for serial devices. This field sets the serial port address to either COM1 or

COM2 (COM1=0x3F8, COM2=0x2F8). This option is set to Serial Device1=COM2 or Serial Device 2=COM1

by default.

NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature. To use console

redirection by SOL, configure the same port address for console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The

serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings

from within the BIOS setup utility may not always revert the serial MUX setting to the default

setting of Serial Device 1.

External Serial

Connector

Enables you to associate the External Serial Connector to Serial Device 1, Serial Device 2, or the Remote

Access Device by using this option. This option is set to Serial Device 1 by default.

NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use console redirection by

SOL, configure the same port address for console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The

serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings

from within the BIOS setup utility may not always revert this setting to the default setting of

Serial Device 1.

Failsafe Baud Rate Specifies the failsafe baud rate for console redirection. The BIOS attempts to determine the baud rate

automatically. This failsafe baud rate is used only if the attempt fails, and the value must not be changed. This

option is set to 115200 by default.

Remote Terminal

Type

Sets the remote console terminal type. This option is set to ANSIVT100/VT220 by default.

Redirection After

Boot

Enables or disables the BIOS console redirection when the operating system is loaded. This option is set to

Enabled by default.

System Profile Settings

You can use the System Profile Settings screen to enable specific system performance settings such as power management.

Viewing System Profile Settings

To view the System Profile Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

30 PowerEdge T340 Pre-operating system management applications

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Profile Settings.

System Profile Settings details

About this task

The System Profile Settings screen details are explained as follows:

Option Description

System Profile Sets the system profile. If you set the System Profile option to a mode other than Custom, the BIOS

automatically sets the rest of the options. You can only change the rest of the options if the mode is set to

Custom. This option is set to Performance Per Watt (OS) by default.

NOTE: All the parameters on the system profile setting screen are available only when the System

Profile option is set to Custom.

CPU Power

Management

Sets the CPU power management. This option is set to OS DBPM by default.

Memory

Frequency

Sets the speed of the system memory. You can select Maximum Performance, Maximum Reliability, or a

specific speed. This option is set to Maximum Performance by default.

Turbo Boost Enables or disables the processor to operate in the turbo boost mode. This option is set to Enabled by default.

C1E Enables or disables the processor to switch to a minimum performance state when it is idle. This option is set to

Enabled by default.

C States Enables or disables the processor to operate in all available power states. This option is set to Enabled by default.

Memory Refresh

Rate

Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.

Uncore Frequency Enables you to select the Processor Uncore Frequency option.

Dynamic mode enables the processor to optimize power resources across the cores and uncore during runtime.

The optimization of the uncore frequency to either save power or optimize performance is influenced by the

setting of the Energy Efficiency Policy option.

Number of Turbo

Boost Enabled

Cores for

Processor 1

NOTE: If there are two processors installed in the system, you will see an entry for Number of

Turbo Boost Enabled Cores for Processor 2.

Controls the number of turbo boost enabled cores for Processor 1. The maximum number of cores is enabled by

default.

Monitor/Mwait Enables the Monitor/Mwait instructions in the processor. This option is set to Enabled for all system profiles,

except Custom by default.

NOTE: This option can be disabled only if the C States option in the Custom mode is set to

disabled.

NOTE: When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting

does not impact the system power or performance.

PCI ASPM L1 Link

Power

Management

Enables or disables the PCI ASPM L1 Link Power Management. This option is set to Enabled by default.

PowerEdge T340 Pre-operating system management applications 31

System Security

You can use the System Security screen to perform specific functions such as setting the system password, setup password and

disabling the power button.

Viewing System Security

To view the System Security screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Security.

System Security Settings details

About this task

The System Security Settings screen details are explained as follows:

Option Description

CPU AES-NI Improves the speed of applications by performing encryption and decryption by using the Advanced Encryption

Standard Instruction Set (AES-NI). This option is set to Enabled by default.

System Password Sets the system password. This option is set to Enabled by default and is read-only if the password jumper is not

installed in the system.

Setup Password Sets the setup password. This option is read-only if the password jumper is not installed in the system.

Password Status Locks the system password. This option is set to Unlocked by default.

TPM Security NOTE: The TPM menu is available only when the TPM module is installed.

Enables you to control the reporting mode of the TPM. The TPM Security option is set to Off by default. You

can only modify the TPM Status, and TPM Activation fields if the TPM Status field is set to either On with Pre-

boot Measurements or On without Pre-boot Measurements.

TPM Information Changes the operational state of the TPM. This option is set to No Change by default.

TPM Status Specifies the TPM status.

TPM Command Controls the Trusted Platform Module (TPM). When set to None, no command is sent to the TPM. When set to

Activate, the TPM is enabled and activated. When set to Deactivate, the TPM is disabled and deactivated.

When set to Clear, all the contents of the TPM are cleared. This option is set to None by default.

CAUTION: Clearing the TPM results in the loss of all keys in the TPM. The loss of TPM keys may

affect booting to the operating system.

This field is read-only when TPM Security is set to Off. The action requires an additional reboot before it can

take effect.

Intel(R) TXT Enables or disables the Intel Trusted Execution Technology (TXT) option. To enable the Intel TXT option,

virtualization technology and TPM Security must be enabled with Pre-boot measurements. This option is set to

Off by default.

When TPM 2.0 is installed, TPM 2 Algorithm option is available. It enables you to select a hash algorithm from

those supported by the TPM (SHA1, SHA256). TPM 2 Algorithm option must be set to SHA256, to enable TXT.

Intel(R) SGX Enables or disables the Intel Software Guard Extension (SGX) option. This option is set to Software by default.

32 PowerEdge T340 Pre-operating system management applications

Option Description

NOTE: The SGX menu is available, only when the SGX supported processor is installed.

SGX Launch

Control Policy

Allows controlling the Launch Control Policy (LCP) of Software Guard Extensions (SGX) technology. This option

is set to Unlocked by default.

Power Button Enables or disables the power button on the front of the system. This option is set to Enabled by default.

AC Power

Recovery

Sets how the system behaves after AC power is restored to the system. This option is set to Last by default.

AC Power

Recovery Delay

Sets the time delay for the system to power up after AC power is restored to the system. This option is set to

Immediate by default.

User Defined

Delay (60 s to 240

Sets the User Defined Delay option when the User Defined option for AC Power Recovery Delay is selected.

UEFI Variable

Access

Provides varying degrees of securing UEFI variables. When set to Standard (the default), UEFI variables are

accessible in the operating system per the UEFI specification. When set to Controlled, selected UEFI variables

are protected in the environment and new UEFI boot entries are forced to be at the end of the current boot

order.

In-Band

Manageability

Interface

When set to Disabled, this setting will hide the Management Engine's (ME), HECI devices, and the system's IPMI

devices from the operating system. This prevents the operating system from changing the ME power capping

settings, and blocks access to all in-band management tools. All management should be managed through out-of-

band. This option is set to Enabled by default.

NOTE: BIOS update requires HECI devices to be operational and DUP updates require IPMI

interface to be operational. This setting needs to be set to Enabled to avoid updating errors.

Secure Boot Enables Secure Boot, where the BIOS authenticates each pre-boot image by using the certificates in the Secure

Boot Policy. Secure Boot is set to Disabled by default.

Secure Boot

Policy

When Secure Boot policy is set to Standard, the BIOS uses the system manufacturer’s key and certificates to

authenticate pre-boot images. When Secure Boot policy is set to Custom, the BIOS uses the user-defined key

and certificates. Secure Boot policy is set to Standard by default.

Secure Boot Mode Configures how the BIOS uses the Secure Boot Policy Objects (PK, KEK, db, dbx).

If the current mode is set to Deployed Mode, the available options are User Mode and Deployed Mode. If the

current mode is set to User Mode, the available options are User Mode, Audit Mode, and Deployed Mode.

Options Description

User Mode In User Mode, PK must be installed, and BIOS performs signature verification on

programmatic attempts to update policy objects.

The BIOS allows unauthenticated programmatic transitions between modes.

Audit Mode In Audit mode, PK is not present. The BIOS does not authenticate programmatic updates

to the policy objects, and transitions between modes.

Audit Mode is useful for programmatically determining a working set of policy objects.

BIOS performs signature verification on pre-boot images and logs results in the image

Execution Information Table, but executes the images whether they pass or fail

verification.

Deployed Mode Deployed Mode is the most secure mode. In Deployed Mode, PK must be installed and

the BIOS performs signature verification on programmatic attempts to update policy

objects.

Deployed Mode restricts the programmatic mode transitions.

Secure Boot

Policy Summary

Specifies the list of certificates and hashes that secure boot uses to authenticate images.

PowerEdge T340 Pre-operating system management applications 33

Option Description

Secure Boot

Custom Policy

Settings

Configures the Secure Boot Custom Policy. To enable this option, set the Secure Boot Policy to Custom option.

Creating a system and setup password

Prerequisites

Ensure that the password jumper is enabled. The password jumper enables or disables the system password and setup password features.

For more information, see the System board jumper settings section.

NOTE: If the password jumper setting is disabled, the existing system password and setup password are deleted and

you need not provide the system password to boot the system.

Steps

1. To enter System Setup, press F2 immediately after turning on or rebooting your system.

2. On the System Setup Main Menu screen, click System BIOS > System Security.

3. On the System Security screen, verify that Password Status is set to Unlocked.

4. In the System Password field, type your system password, and press Enter or Tab.

Use the following guidelines to assign the system password:

• A password can have up to 32 characters.

• The password can contain the numbers 0 through 9.

• Only the following special characters are allowed: space, (”), (+), (,), (-), (.), (/), (;), ([), (\), (]), (`).

A message prompts you to reenter the system password.

5. Reenter the system password, and click OK.

6. In the Setup Password field, type your setup password and press Enter or Tab.

A message prompts you to reenter the setup password.

7. Reenter the setup password, and click OK.

8. Press Esc to return to the System BIOS screen. Press Esc again.

A message prompts you to save the changes.

NOTE: Password protection does not take effect until the system reboots.

Using your system password to secure the system

About this task

If you have assigned a setup password, the system accepts your setup password as an alternate system password.

Steps

1. Power on or reboot your system.

2. Type the system password and press Enter.

Next steps

When Password Status is set to Locked, type the system password and press Enter when prompted at reboot.

NOTE: If an incorrect system password is typed, the system displays a message and prompts you to reenter your

password. You have three attempts to type the correct password. After the third unsuccessful attempt, the system

displays an error message that the system has stopped functioning and must be turned off. Even after you turn off and

restart the system, the error message is displayed until the correct password is entered.

34 PowerEdge T340 Pre-operating system management applications

Deleting or changing system and setup password

Prerequisites

NOTE: You cannot delete or change an existing system or setup password if the Password Status is set to Locked.

Steps

1. To enter System Setup, press F2 immediately after turning on or restarting your system.

2. On the System Setup Main Menu screen, click System BIOS > System Security.

3. On the System Security screen, ensure that Password Status is set to Unlocked.

4. In the System Password field, change or delete the existing system password, and then press Enter or Tab.

5. In the Setup Password field, alter or delete the existing setup password, and then press Enter or Tab.

NOTE: If you change the system password or setup password, a message prompts you to reenter the new password.

If you delete the system password or setup password, a message prompts you to confirm the deletion.

6. Press Esc to return to the System BIOS screen. Press Esc again, and a message prompts you to save the changes.

7. Select Setup Password, change, or delete the existing setup password and press Enter or Tab.

NOTE: If you change the system password or setup password, a message prompts you to reenter the new password.

If you delete the system password or setup password, a message prompts you to confirm the deletion.

Operating with setup password enabled

If Setup Password is set to Enabled, type the correct setup password before modifying the system setup options.

If you do not type the correct password in three attempts, the system displays the following message:

Invalid Password! Number of unsuccessful password attempts: <x> System Halted! Must power

down.

Password Invalid. Number of unsuccessful password attempts: <x> Maximum number of password

attempts exceeded.System halted.

Even after you turn off and restart the system, the error message is displayed until the correct password is typed. The following options

are exceptions:

• If System Password is not set to Enabled and is not locked through the Password Status option, you can assign a system

password. For more information, see the System Security Settings screen section.

• You cannot disable or change an existing system password.

NOTE: You can use the password status option with the setup password option to protect the system password from

unauthorized changes.

Redundant OS Control

In the Redundant OS Control screen you can set the redundant OS information. This enables you to set up a physical recovery disk on

the system.

Viewing Redundant OS Control

To view the Redundant OS Control screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

PowerEdge T340 Pre-operating system management applications 35

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Redundant OS Control.

Redundant OS Control screen details

The Redundant OS Control screen details are explained as follows:

About this task

Option Description

Redundant OS

Location

Enables you to select a backup disk from the following devices:

•None

•IDSDM

•SATA Ports in AHCI mode

•BOSS PCIe Cards (Internal M.2 Drives)

•Internal USB

NOTE: RAID configurations and NVMe cards not are included as BIOS does not have the ability to

distinguish between individual drives in those configurations.

Redundant OS

State NOTE: This option is disabled if Redundant OS Location is set to None.

When set to Visible, the backup disk is visible to the boot list and OS. When set to Hidden, the backup disk is

disabled and is not visible to the boot list and OS. This option is set to Visible by default.

NOTE: BIOS will disable the device in hardware, so it cannot be accessed by the OS.

Redundant OS

Boot

NOTE: This option is disabled if Redundant OS Location is set to None or if Redundant OS State is

set to Hidden.

When set to Enabled, BIOS boots to the device specified in Redundant OS Location. When set to Disabled,

BIOS preserves the current boot list settings. This option is set to Disabled by default.

Miscellaneous Settings

You can use the Miscellaneous Settings screen to perform specific functions such as updating the asset tag and changing the system

date and time.

Viewing Miscellaneous Settings

To view the Miscellaneous Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Miscellaneous Settings.

36 PowerEdge T340 Pre-operating system management applications

Miscellaneous Settings details

About this task

The Miscellaneous Settings screen details are explained as follows:

Option Description

System Time Enables you to set the time on the system.

System Date Enables you to set the date on the system.

Asset Tag Specifies the asset tag and enables you to modify it for security and tracking purposes.

Keyboard

NumLock

Enables you to set whether the system boots with the NumLock enabled or disabled. This option is set to On by

default.

NOTE: This option does not apply to 84-key keyboards.

F1/F2 Prompt on

Error

Enables or disables the F1/F2 prompt on error. This option is set to Enabled by default. The F1/F2 prompt also

includes keyboard errors.

Load Legacy Video

Option ROM

Enables you to determine whether the system BIOS loads the legacy video (INT 10H) option ROM from the video

controller. Selecting Enabled in the operating system does not support UEFI video output standards. This field is

available only for UEFI boot mode. You cannot set the option to Enabled if UEFI Secure Boot mode is enabled.

This option is set to Disabled by default.

Dell Wyse

P25/P45 BIOS

Access

Enables or disables the Dell Wyse P25/P45 BIOS Access. This option is set to Enabled by default.

Power Cycle

Request

Enables or disables the Power Cycle Request. This option is set to None by default.

iDRAC Settings utility

The iDRAC settings utility is an interface to set up and configure the iDRAC parameters by using UEFI. You can enable or disable various

iDRAC parameters by using the iDRAC settings utility.

NOTE: Accessing some of the features on the iDRAC settings utility needs the iDRAC Enterprise License upgrade.

For more information about using iDRAC, see Dell Integrated Dell Remote Access Controller User's Guide at www.dell.com/

poweredgemanuals.

Device Settings

Device Settings enables you to configure the below device parameters:

• Controller Configuration Utility

• Embedded NIC Port1-X Configuration

• NICs in slotX, Port1-X Configuration

• BOSS Card configuration

Dell Lifecycle Controller

Dell Lifecycle Controller (LC) provides advanced embedded systems management capabilities including system deployment, configuration,

update, maintenance, and diagnosis. LC is delivered as part of the iDRAC out-of-band solution and Dell system embedded Unified

Extensible Firmware Interface (UEFI) applications.

Embedded system management

The Dell Lifecycle Controller provides advanced embedded system management throughout the lifecycle of the system. The Dell Lifecycle

Controller can be started during the boot sequence and can function independently of the operating system.

PowerEdge T340 Pre-operating system management applications 37

NOTE: Certain platform configurations may not support the full set of features provided by the Dell Lifecycle Controller.

For more information about setting up the Dell Lifecycle Controller, configuring hardware and firmware, and deploying the operating

system, see the Dell Lifecycle Controller documentation at www.dell.com/poweredgemanuals.

Boot Manager

The Boot Manager screen enables you to select boot options and diagnostic utilities.

Viewing Boot Manager

About this task

To enter Boot Manager:

Steps

1. Power on, or restart your system.

2. Press F11 when you see the following message:

F11 = Boot Manager

If your operating system begins to load before you press F11, allow the system to complete the booting, and then restart your system

and try again.

Boot Manager main menu

Menu item Description

Continue Normal

Boot

The system attempts to boot to devices starting with the first item in the boot order. If the boot attempt fails, the

system continues with the next item in the boot order until the boot is successful or no more boot options are

found.

One-shot Boot

Enables you to access boot menu, where you can select a one-time boot device to boot from.

Launch System

Setup

Enables you to access System Setup.

Launch Lifecycle

Controller

Exits the Boot Manager and invokes the Dell Lifecycle Controller program.

System Utilities Enables you to launch System Utilities menu such as System Diagnostics and UEFI shell.

One-shot UEFI boot menu

One-shot UEFI boot menu enables you to select a boot device to boot from.

System Utilities

System Utilities contains the following utilities that can be launched:

• Launch Diagnostics

• BIOS Update File Explorer

• Reboot System

PXE boot

You can use the Preboot Execution Environment (PXE) option to boot and configure the networked systems, remotely.

38 PowerEdge T340 Pre-operating system management applications

To access the PXE boot option, boot the system and then press F12 during POST instead of using standard Boot Sequence from BIOS

Setup. It does not pull any menu or allows managing of network devices.

PowerEdge T340 Pre-operating system management applications 39

Installing and removing system components

Safety instructions

NOTE: Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the system

by yourself.

WARNING: Opening or removing the system cover while the system is powered on may expose you to a risk of electric

shock.

CAUTION: Do not operate the system without the cover for a duration exceeding five minutes. Operating the system

without the system cover can result in component damage.

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

simple repairs as authorized in your product documentation, or as directed by the online or telephone service and

support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow

the safety instructions that are shipped with your product.

CAUTION: To ensure proper operation and cooling, all bays in the system and system fans must be always populated

with a component or a blank.

NOTE: It is recommended that you always use an antistatic mat and antistatic strap while working on components inside

the system.

Before working inside your system

Prerequisites

Follow the safety guidelines listed in Safety instructions.

Steps

1. Power off the system and all attached peripherals.

2. Disconnect the system from the electrical outlet, and disconnect the peripherals.

3. Remove the system cover.

After working inside your system

Prerequisites

Follow the safety guidelines listed in Safety instructions on page 40.

Steps

1. Install the system cover.

2. Place the system upright on a flat, stable surface.

3. Reconnect the peripherals and connect the system to the electrical outlet.

4. Power on the attached peripherals and then power on the system.

Recommended tools

You need the following tools to perform the removal and installation procedures:

40 Installing and removing system components

• Key to the bezel lock

The key is required only if your system includes a bezel.

• Phillips #1 screwdriver

• Phillips #2 screwdriver

• 5mm hex nut screwdriver

• Plastic scribe

• Wrist grounding strap connected to the ground

• ESD mat

Front bezel

Removing the front bezel

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Keep the bezel key handy.

Steps

1. Unlock the bezel.

2. Press the blue release latch at the top of the bezel to release the bezel from the system.

3. Unhook the bezel tabs from the slots at the bottom, and lift the bezel.

Figure 17. Removing the front bezel

Next steps

1. Replace the front bezel.

Installing the front bezel

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

Installing and removing system components 41

2. Locate and remove the bezel key.

NOTE: The bezel key is part of the bezel package.

Steps

1. Align and insert the bezel tabs into the slots in the system.

2. Press the release latch, and push the bezel toward the system until the bezel locks into place.

3. Lock the bezel.

Figure 18. Installing the front bezel

System feet

Removing the system feet

Prerequisites

NOTE: It is recommended that you remove the system feet only when you are replacing the system feet with the wheel

assembly.

1. Follow the safety guidelines listed in Safety instructions..

2. Place the system on its side on a flat, stable surface.

3. Rotate the system feet inward.

Steps

1. Using the Phillips #2 screwdriver, remove the screw that secures the foot to the base of the system.

2. Repeat the preceding step to remove the remaining system feet.

42 Installing and removing system components

Figure 19. Removing the system feet

Next steps

1. Replace the system feet or install the caster wheels.

Installing the system feet

Prerequisites

CAUTION: Install the feet on a stand-alone tower system to provide stability to the system. An unstable system might

tip over and cause injury to the user or damage to the system.

1. Follow the safety guidelines listed in Safety instructions.

2. Place the system on its side on a flat, stable surface.

Steps

1. Align the three tabs on the system foot with the three slots on the base of the system.

2. Using the Phillips #2 screwdriver, secure the screw that secures the foot to the base of the system.

3. Repeat the above steps to install the remaining system feet.

Installing and removing system components 43

Figure 20. Installing the system feet

Next steps

1. Place the system upright on a flat, stable surface, and rotate the system feet outward.

2. Follow the procedure listed in After working inside your system.

Caster wheels – optional

Removing caster wheels

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Place the system on its side on a flat, stable surface.

Steps

1. Using the Phillips #2 screwdriver, loosen the captive screw that secures the front wheel unit to the base of the system.

2. Push the front wheel unit toward the rear of the system to release the retention hooks, and pull out the front wheel unit.

3. Loosen the screw that secures the back wheel unit to the base of the system.

4. Push the rear wheel unit toward the front of the system to release the retention hooks, and pull out the rear wheel unit.

44 Installing and removing system components

Next steps

1. Replace the caster wheels or replace the system feet, as applicable.

Installing caster wheels

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Place the system on its side on a flat, stable surface.

3. If installed, remove the system feet.

Steps

1. Align the two retention hooks on the rear wheel unit with the two slots on the base of the system, and insert the hooks into the slots.

2. Push the rear wheel unit toward the back of the system and using a Phillips #2 screwdriver secure the unit in place using a single

screw.

3. Align the two retention hooks on the front wheel unit with the two slots on the base of the system, and insert the hooks into the slots.

4. Push the front wheel unit toward the front of the system and using a Phillips #2 screwdriver secure the unit in place using a single

screw.

Installing and removing system components 45

Figure 21. Installing caster wheels

Next steps

1. Follow the procedure listed in After working inside your system.

System cover

Removing the system cover

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Power off the system and all attached peripherals.

3. Disconnect the system from the electrical outlet and disconnect the peripherals.

4. Place the system on a flat, stable surface.

5. Remove the front bezel.

Steps

1. Use a 1/4-inch flat head or a Phillips #2 screwdriver to turn the cover release latch counterclockwise to the unlock position.

2. Press the cover release latch, and remove the system cover.

46 Installing and removing system components

Figure 22. Removing the system cover

Installing the system cover

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Remove the front bezel.

3. Power off the system and all attached peripherals.

4. Disconnect the system from the electrical outlet and disconnect the peripherals.

5. Ensure that all internal cables are connected and placed out of the way and no tools or extra parts are left inside the system.

Steps

1. Align the tabs on the system cover with the slots on the system.

2. Press the cover release latch, and push the cover toward the system until the latch locks into place.

3. Using a 1/4-inch flat head or a Phillips #2 screwdriver, rotate the cover release latch lock clockwise to the locked position.

Installing and removing system components 47

Figure 23. Installing the system cover

Next steps

1. Place the system upright on its feet on a flat, stable surface.

2. Install the front bezel.

3. Reconnect the peripherals, and connect the system to the electrical outlet.

4. Power on the system and all attached peripherals.

Air shroud

Removing the air shroud

Prerequisites

CAUTION: Never operate your system with the air shroud removed. The system may get overheated quickly, resulting in

shutdown of the system and loss of data.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the system cover.

Steps

Holding the blue touch points, lift the air shroud out of the system.

48 Installing and removing system components

Figure 24. Removing the air shroud

Next steps

1. Replace the air shroud.

Installing the air shroud

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. If applicable, route the cables inside the system along the system wall and secure the cables by using the cable-securing bracket.

Steps

1. Align the tabs on the air shroud with the slots on the system.

2. Lower the air shroud into the system until it is firmly seated.

Installing and removing system components 49

Figure 25. Installing the air shroud

Next steps

1. Install the system cover.

2. Follow the procedure listed in Before working inside your system.

Intrusion switch

Removing the intrusion switch

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Keep the plastic scribe ready.

Steps

1. Disconnect the intrusion switch cable connector from the system board.

NOTE: Observe the routing of the cable as you remove it from the system. Route the cable properly when you

replace it to prevent the cable from being pinched or crimped.

2. Using the plastic scribe, slide the intrusion switch out of the intrusion switch slot.

50 Installing and removing system components

Figure 26. Removing the intrusion switch

Next steps

1. Replace the intrusion switch.

Installing the intrusion switch

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Align and slide the intrusion switch into the slot in the system.

2. Connect the intrusion switch cable connector to the intrusion switch connector on the system board.

Figure 27. Installing the intrusion switch

Installing and removing system components 51

Next steps

1. Install the air shroud.

2. Follow the procedure that is listed in After working inside your system.

Drives

Removing a drive blank

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

CAUTION: To maintain proper system cooling, drive blanks must be installed in all empty drive slots.

CAUTION: Mixing drive blanks from previous generations of PowerEdge servers is not supported.

Steps

Press the release tab, and slide the drive blank out.

Figure 28. Removing a drive blank

NOTE: The procedure to remove a 2.5-inch or a 3.5-inch drive blank is the same.

Next steps

1. Replace the drive or a drive blank.

Installing a drive blank

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure in Before working inside your system.

3. Remove the front bezel.

CAUTION: To maintain proper system cooling, drive blanks must be installed in all empty drive slots.

CAUTION: Mixing drive blanks from previous generations of PowerEdge servers is not supported.

52 Installing and removing system components

Steps

Slide the drive blank into the drive slot until the release tab clicks into place.

Figure 29. Installing a drive blank

Next steps

1. Replace the front bezel.

2. Follow the procedure listed in After working inside your system.

Removing a drive carrier

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Remove the front bezel.

3. Using the management software, prepare the drive for removal.

If the drive is online, the green activity or fault indicator flashes while the drive is turning off. When the drive indicators are off, the

drive is ready for removal. For more information, see the storage controller documentation.

CAUTION: Before attempting to remove or install a drive while the system is running, see the documentation for the

storage controller card to ensure that the host adapter is configured correctly to support drive removal and

insertion.

CAUTION: To prevent data loss, ensure that your operating system supports drive installation. See the

documentation supplied with your operating system.

Steps

1. Press the release button to open the drive carrier release handle.

2. Holding the handle, slide the drive carrier out of the drive slot.

NOTE: If you are not replacing the drive immediately, install a drive blank in the empty drive slot to maintain proper

system cooling.

Installing and removing system components 53

Figure 30. Removing a drive carrier

Next steps

Replace the drive or a drive blank.

Installing the drive carrier

Prerequisites

CAUTION: Before removing or installing a drive while the system is running, see the documentation for the storage

controller card to ensure that the host adapter is configured correctly to support drive removal and insertion.

CAUTION: Combining SAS and SATA drives in the same RAID volume is not supported.

CAUTION: When installing a drive, ensure that the adjacent drives are fully installed. Inserting a drive carrier and

attempting to lock its handle next to a partially installed carrier can damage the partially installed carrier's shield spring

and make it unusable.

NOTE: Ensure that the drive carrier's release handle is in the open position before inserting the carrier into the slot.

CAUTION: To prevent data loss, ensure that your operating system supports hot-swap drive installation. See the

documentation supplied with your operating system.

CAUTION: When a replacement hot swappable drive is installed and the system is powered on, the drive automatically

begins to rebuild. Ensure that the replacement drive is blank or contains data that you wish to overwrite. Any data on

the replacement drive is immediately lost after the drive is installed.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

4. If installed, remove a drive blank.

Steps

1. Press the release button on the front of the drive carrier to open the release handle.

2. Insert the drive carrier into the drive slot and push until the drive connects with the backplane.

3. Close the drive carrier release handle to lock the drive in place.

54 Installing and removing system components

NOTE: The procedure to install a 2.5-inch or a 3.5-inch drive are the same.

Figure 31. Installing a drive carrier

Next steps

1. Install the front bezel.

2. Follow the procedure listed in After working inside your system.

Removing the drive from the drive carrier

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

CAUTION: Mixing drive carriers from previous generations of PowerEdge servers is not supported.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

4. Remove the drive carrier.

Steps

1. Using a Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier.

2. Lift the drive out of the drive carrier.

Installing and removing system components 55

Figure 32. Removing the drive from the drive carrier

Next steps

1. Replace the drive into the drive carrier.

Installing the drive into the drive carrier

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

4. Remove the drive carrier.

CAUTION: Mixing drive carriers from other generations of PowerEdge servers is not supported.

Steps

1. Insert the drive into the drive carrier with the connector end of the drive towards the back of the carrier.

2. Align the screw holes on the drive with the screws holes on the drive carrier. When aligned correctly, the back of the drive is flush with

the back of the drive carrier.

3. Using a Phillips #1 screwdriver, replace the screws to secure the drive to the drive carrier.

NOTE: When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-pounds.

NOTE: Use the screws shipped with the drive carrier to secure the drive to the drive carrier.

56 Installing and removing system components

Figure 33. Installing a drive into the drive carrier

Next steps

1. Replace the drive carrier.

2. Install the front bezel.

3. Follow the procedure listed in After working inside your system.

Removing a 2.5-inch drive from the 3.5-inch drive adapter

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove 3.5-inch drive adapter from the 3.5-inch drive carrier.

NOTE: A 2.5 inch hot swappable drive is installed in a 3.5-inch drive adapter, which is then installed in the 3.5-inch hot

swappable drive carrier.

Steps

1. Using a Phillips #1 screwdriver, remove the screws from the side of the 3.5-inch drive adapter.

2. Remove the drive from the 3.5-inch drive adapter.

Installing and removing system components 57

Figure 34. Removing a 2.5-inch drive from the 3.5-inch drive adapter

Next steps

Replace a 2.5-inch drive into the 3.5-inch drive adapter.

Installing a 2.5-inch drive into the 3.5-inch drive adapter

Prerequisites

Follow the safety guidelines listed in Safety instructions.

Steps

1. Align the screw holes on the 2.5-inch drive with the screw holes on the 3.5-inch drive adapter.

2. Using a Phillips #1 screwdriver, install the screws to secure the drive to the 3.5-inch drive adapter.

58 Installing and removing system components

Figure 35. Installing a 2.5-inch drive into the 3.5-inch drive adapter

Next steps

1. Replace a 3.5-inch adapter into the 3.5-inch drive carrier.

2. Follow the procedure listed in After working inside your system.

Removing a 3.5-inch drive adapter from a 3.5-inch drive

carrier

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the 3.5-inch drive carrier from the system.

Steps

1. Remove the screws from the rails on the drive carrier.

2. Lift the 3.5 inch drive adapter out of the drive carrier.

Installing and removing system components 59

Figure 36. Removing a 3.5-inch drive adapter from a 3.5-inch drive carrier

Next steps

Replace a 3.5-inch adapter into a 3.5-inch drive carrier.

Installing a 3.5-inch adapter into a 3.5-inch drive carrier

Prerequisites

Follow the safety guidelines listed in Safety instructions.

Steps

1. Insert the 3.5 inch drive adapter into the drive carrier with the connector end of the drive toward the back of the drive carrier.

2. Align the screw holes on the drive with the holes on the drive carrier.

3. Install the screws to secure the drive to the drive carrier.

Figure 37. Installing a 3.5-inch drive adapter into the 3.5-inch drive carrier

60 Installing and removing system components

Next steps

1. Replace a 3.5-inch drive carrier into the system.

2. Follow the procedure listed in After working inside your system.

Optical drive and tape drives

Removing the optical or tape drive blank

Prerequisites

NOTE: The procedure to remove the optical drive blank is identical to removing a tape drive blank.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

Steps

1. Slide the release latch downwards to remove the drive blank.

2. Push the drive blank to slide it out of the drive bay.

Figure 38. Removing the optical drive or tape drive blank

NOTE: Blanks must be installed on empty optical drive or tape drive slots to maintain FCC certification of the

system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the

system. Perform the same steps to install blanks.

Next steps

Replace the optical drive blank, or an optical drive, or a tape drive.

Installing and removing system components 61

Installing the optical or tape drive blank

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Remove the front bezel.

Steps

1. Align the guide on the drive blank with the slot on drive bay.

2. Slide the drive into the slot until the latch snaps into place.

Figure 39. Installing the optical or tape drive blank

Next steps

1. Install the front bezel.

2. Follow the procedure listed in After working inside your system.

Removing the optical drive

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

Steps

1. Disconnect the power and data cable connectors from the connectors on the optical drive.

NOTE: Observe the routing of the power and data cable inside the chassis as you remove them from the system

board and the drive. You must route these cables properly when you replace them to prevent them from being

pinched or crimped.

2. To remove the drive, slide the release latch downwards to release the drive.

3. Slide the drive out of the drive bay.

4. If you are not immediately replacing the tape drive, install the blank.

62 Installing and removing system components

NOTE: Blanks must be installed on empty optical drive or tape drive slots to maintain FCC certification of the

system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the

system. Perform the same steps to install blanks.

Figure 40. Removing the optical drive

Next steps

1. Replace the optical drive.

2. Follow the procedure listed in After working inside your system.

Installing the optical drive

Prerequisites

1. Ensure that you follow the procedure listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

4. If applicable, remove the optical drive blank.

NOTE: The procedure to remove the optical drive blank and the optical drive is similar.

Steps

1. Align the slide the optical drive into the slot until the latch clicks into place.

2. Connect the power and data cable connectors to the connectors on the optical drive.

3. Connect the power and data cable connectors to the backplane and the system board.

NOTE: Route the cables properly to prevent them from being pinched or crimped.

Installing and removing system components 63

Figure 41. Installing the optical drive

Next steps

1. Install the front bezel.

2. Follow the procedure listed in After working inside your system.

Removing the tape drive

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

Steps

1. Disconnect the power and data cable connectors from the connectors on the tape drive.

NOTE: Observe the routing of the power and data cable connectors inside the chassis as you remove them from the

system board and the drive. You must route these cables properly when you replace them to prevent them from

being pinched or crimped.

2. Using the Phillips #2 screwdriver, remove the screw that secures the tape drive.

3. Push the release latch to release the drive.

4. Slide the drive out of the drive bay.

5. If you are not immediately replacing the tape drive, install the blank.

NOTE: Blanks must be installed on empty tape drive slots to maintain FCC certification of the system. The brackets

also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. Perform the same

steps to install blanks.

64 Installing and removing system components

Figure 42. Removing the tape drive

Next steps

1. Replace the tape drive.

2. Follow the procedure listed in After working inside your system.

Installing the tape drive

Prerequisites

1. Ensure that you follow the procedure listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

4. If applicable, remove the tape drive blank.

NOTE: The procedure to remove the tape drive blank and the tape drive is similar.

Steps

1. Align and slide the tape drive into the tape drive bay until it clicks into place.

2. Using the Phillips #2 screwdriver, secure the tape drive to the drive bay.

3. Connect the power and data cable connectors to the connectors on the tape drive.

4. Connect the power and data cable connectors to the backplane and the system board.

NOTE: Route the cables properly to prevent them from being pinched or crimped.

Installing and removing system components 65

Figure 43. Installing the tape drive

Next steps

1. Install the front bezel.

2. Follow the procedure listed in After working inside your system.

Drive backplane

Drive backplane details

Your system supports the following backplane configuration:

• x8 SAS/SATA backplane for 3.5-inch drives

NOTE: The x8 backplane also supports up to eight 2.5-inch (SAS, SATA, or SSD) hot swappable drives that can be

installed in 3.5-inch drive adapters, which can be installed in the 3.5-inch drive carriers.

66 Installing and removing system components

Figure 44. x8 SAS/SATA backplane for 3.5-inch drives

1. ODD power connector (P1)

2. Backplane P4 power connector (BP_PWR)

3. Backplane sideband signal connector (BP_SIG)

4. Mini SAS SAS_A0

5. Mini SAS SAS_B0

Removing the drive backplane

Prerequisites

CAUTION: Note the number of each drive and temporarily label them before you remove the drive so that you can

replace them in the same location.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel.

4. Remove all the drives.

CAUTION: To prevent damage to the drives and backplane, remove the drives from the system before removing the

backplane.

5. Remove the air shroud.

Steps

1. Disconnect the data, signal, and power cables from the backplane.

2. Pull the release pin to disengage the backplane from the system.

3. Lift the backplane out of the system.

Installing and removing system components 67

Figure 45. Removing the drive backplane

Next steps

1. Replace a drive backplane.

2. Follow the procedure listed in After working inside your system.

Installing the drive backplane

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the front bezel..

4. Remove the air shroud.

5. Remove all the drives.

Steps

1. Align the slots on the backplane with the hooks on the system.

2. Lower the drive backplane into the system until the release pin locks in place, securing the drive backplane to the system.

3. Connect the data, signal, and power cables to the backplane.

68 Installing and removing system components

Figure 46. Installing the drive backplane

Next steps

1. Install the air shroud.

2. Install the drives.

3. Install the front bezel.

4. Follow the procedure listed in After working inside your system.

Backplane cable routing

Figure 47. Cable routing - 8 x 3.5-inch, SATA drive backplane

Installing and removing system components 69

Figure 48. Cable routing - 8 x 3.5-inch SAS/SATA drive backplane with PERC card

Four-slot drive blank

Systems with x8 drive backplanes configured for software RAID support only four drives. The remaining drive slots are pre-installed with

the four-slot drive blank, and cannot be upgraded for additional storage.

Removing a four-slot drive blank

Prerequisites

CAUTION: To maintain proper system cooling, all empty drive slots must have drive blanks installed.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

CAUTION: To prevent damage to the drives and backplane, you must remove the drives from the system before

removing the backplane.

CAUTION: Note the slot number of each drive and temporarily label the slots before removing the drives so that you

can replace them in the same locations.

3. Remove the air shroud.

4. Remove all the drives.

5. Remove the drive backplane.

Steps

1. Using a screwdriver, push the release tabs on the corners of the blank from inside the system, to unlock the four-slot hard drive blank

from the chassis.

2. From the front of the system, pull the four-slot hard drive blank at the corners until it is free of the hard drive slot.

70 Installing and removing system components

Figure 49. Removing a four-slot drive blank

Next steps

1. Replace a four-slot drive blank.

Installing a four-slot drive blank

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Locate the drive slots numbered from four to seven.

2. Insert the four-slot drive blank into the drive slot, and push it until the release tabs click into place.

Figure 50. Installing a four-slot drive blank

Installing and removing system components 71

Next steps

1. Install the drive backplane.

2. Install the drives.

3. Install the air shroud.

4. Follow the procedure listed in After working inside your system.

System memory

System memory guidelines

The system supports DDR4 unbuffered DIMMs (UDIMMs). System memory holds the instructions that are executed by the processor.

Your system contains 4 memory sockets. Two memory channels are allocated to the processor.

Memory channels are organized as follows:

Figure 51. System memory view

Table 5. Memory channels

Processor Channel 0 Channel 1

Processor 1 Slots A1, A3 Slots A2, A4

The following table shows the memory populations and operating frequencies for the supported configurations:

72 Installing and removing system components

Table 6. Memory population

DIMM Type DIMMs Populated/

Channel Voltage Operating Frequency (in

MT/s)

Maximum DIMM Rank/

Channel

UDIMM 1 1.2 V 2133, 2400, 2666 Dual rank or single rank

2 2133, 2400, 2666 Dual rank or single rank

General memory module installation guidelines

To ensure optimal performance of your system, observe the following general guidelines when configuring your system memory. If your

system's memory configurations fail to observe these guidelines, your system might not boot, stop responding during memory

configuration, or operate with reduced memory.

The memory bus may operate at frequency can be 2666 MT/s, 2400 MT/s, or 2133 MT/s depending on the following factors:

• System profile selected (for example, Performance Optimized, or Custom [can be run at high speed or lower])

• Maximum supported DIMM speed of the processors.

• Maximum supported speed of the DIMMs

NOTE: MT/s indicates DIMM speed in MegaTransfers per second.

The system supports Flexible Memory Configuration, enabling the system to be configured and run in any valid chipset architectural

configuration. The following are the recommended guidelines for installing memory modules:

• All DIMMs must be DDR4.

• A maximum of two different ranked DIMMs can be populated in a channel regardless of rank count.

• If memory modules with different speeds are installed, they will operate at the speed of the slowest installed memory module(s).

• Populate memory module sockets only if a processor is installed.

○For single-processor systems, sockets A1 to A4 are available.

○In Optimizer Mode, the DRAM controllers operate independently in the 64-bit mode and provide optimized memory performance.

Table 7. Memory population rules

Processor Configuration Memory population Memory population information

Single processor Optimizer (Independent channel)

population order

1, 2, 3, 4 Odd amount of DIMMs per

processor allowed.

• Populate all the sockets with white release tabs first, followed by the black release tabs.

• When mixing memory modules with different capacities, populate the sockets with memory modules with the highest capacity first.

For example, if you want to mix 8 GB and 16 GB memory modules, populate 16 GB memory modules in the sockets with white release

tabs and 8 GB memory modules in the sockets with black release tabs.

• Memory modules of different capacities can be mixed provided other memory population rules are followed.

For example, 8 GB and 16 GB memory modules can be mixed.

• Mixing of more than two memory module capacities in a system is not supported.

• Unbalanced memory configurations will result in a performance loss so always populate memory channels identically with identical

DIMMs for best performance.

• To ensure proper system cooling, memory module blanks must be installed in memory sockets that are not occupied.

Removing a memory module

Prerequisites

WARNING: Allow the memory modules to cool after you power off the system. Handle the memory modules by the

edges and avoid touching the components or metallic contacts on the memory module.

CAUTION: To ensure proper system cooling, when processor 1 and processor 2 are installed, memory module blanks

must be installed in memory sockets that are not occupied. Remove memory module blanks only if you intend to install

memory modules in those sockets.

1. Follow the safety guidelines listed in Safety instructions.

Installing and removing system components 73

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

Steps

1. Locate the appropriate memory module socket.

CAUTION: Handle each memory module only by the edges, ensuring not to touch the middle of the memory module

or metallic contacts.

2. Push the ejectors outward on both ends of the memory module socket to release the memory module from the socket.

3. Lift and remove the memory module from the system.

Figure 52. Removing a memory module

NOTE: If you are removing the memory module permanently, install a memory module blank. The procedure to install

a memory module blank is similar to that of the memory module.

Next steps

1. Replace the memory module.

Installing a memory module

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Install the air shroud.

Steps

1. Locate the appropriate memory module socket.

CAUTION: Handle each memory module only by the edges, ensuring not to touch the middle of the memory module

or metallic contacts.

CAUTION: To prevent damage to the memory module or the memory module socket during installation, do not bend

or flex the memory module. You must insert both ends of the memory module simultaneously.

2. Open the ejectors on the memory module socket outward to allow the memory module to be inserted into the socket.

3. Align the edge connector of the memory module with the alignment key of the memory module socket, and insert the memory module

in the socket.

CAUTION: Do not apply pressure at the center of the memory module. Apply pressure at both ends of the memory

module evenly.

74 Installing and removing system components

NOTE: The memory module socket has an alignment key that enables you to install the memory module in the socket

in only one orientation.

4. Press the memory module with your thumbs until the ejectors firmly click into place.

Figure 53. Installing a memory module

Next steps

1. Install the air shroud.

2. Follow the procedure listed in After working inside your system.

3. Verify if the memory module has been installed properly, by pressing F2 and navigating to System Setup Main Menu > System BIOS >

Memory Settings . In the Memory Settings screen, the System Memory Size must reflect the updated capacity of the installed

memory. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is

firmly seated in the memory module socket. Run the system memory test in system diagnostics.

Cooling fan

Removing the internal cooling fan

Prerequisites

CAUTION: Never operate your system cover with the internal fan removed. The system can overheat and result in

shutdown of the system and loss of data.

CAUTION: Do not operate the system with the system cover removed for more than 5 minutes.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

Steps

1. Press the release tabs on the fan cable connector and disconnect it from the connector on the system board.

2. Holding the fan, press the release tab, and slide the fan out in the direction of the arrow marked on the fan.

Installing and removing system components 75

Figure 54. Removing the internal cooling fan

CAUTION: Do not remove or install the fan by holding the fan blades.

Next steps

1. Replace the internal fan.

Installing the internal cooling fan

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud

Steps

1. Align the four tabs on the fan with the four slots on the system wall.

2. Press and slide the fan into the slots until the release tab locks into place.

3. Connect the fan power cable connector to the connector on the system board.

76 Installing and removing system components

Figure 55. Installing the internal cooling fan

Next steps

1. Install the air shroud.

2. Follow the procedure listed in After working inside your system.

Optional internal USB memory key

NOTE: To locate the internal USB port on the system board, see the System board jumpers and connectors section.

Replacing the optional internal USB memory key

Prerequisites

CAUTION: To avoid interference with other components in the server, the maximum permissible dimensions of the USB

memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height.

1. Follow the safety guidelines listed in the Safety instructions.

2. Follow the procedure listed in the Before working inside your system.

3. Remove the air shroud.

Steps

1. Locate the USB port or USB memory key on the system board.

To locate the USB port, see the System board jumpers and connectors section.

2. If installed, remove the USB memory key from the USB port.

3. Insert the replacement USB memory key into the USB port.

Next steps

1. Follow the procedure that is listed in After working inside your system.

2. While booting, press F2 to enter System Setup and verify that the system detects the USB memory key.

Installing and removing system components 77

Expansion cards

NOTE: A System Event Log (SEL) event is logged if an expansion card riser is not supported or missing. It does not

prevent your system from turning on. However, if a F1/F2 pause occurs with an error message, see

Troubleshooting

expansion cards

section in the

Dell EMC PowerEdge Servers Troubleshooting Guide

at www.dell.com/

poweredgemanuals.

Expansion card guidelines

The following table describes the installation order for installing expansion cards to ensure proper cooling and mechanical fit. The

expansion cards with the highest priority must be installed first by using the slot priority indicated.

NOTE: The expansion card slots are not hot-swappable.

Table 8. Expansion card slots supported on the system board

PCIe slot Processor Connection PCIe slot height PCIe slot length Slot width

Slot 1 (Gen3) Processor Full Height Half Length x8 link in x8 slot

Slot 2 (Gen3) Processor Full Height Half Length x8 link in x16 slot

Slot 3 (Gen3) Platform Controller Hub Full Height Half Length x1

Slot 4 (Gen3) Platform Controller Hub Full Height Half Length x4 link in x8 slot

Table 9. Expansion card installation order

Card

Priority

Category Card Type Form Factor Slot Priority Maximum

Allowed

1 Internal Adapter PowerEdge RAID Controller (PERC)

H730P+

Full Height 1,2 1

2 Internal Adapter PowerEdge RAID Controller (PERC)

H330+

Full Height 1,2 1

4 Internal Adapter HBA330 Full Height 1,2 1

6 External Adapter 12 GB SAS HBA Full Height 1,2 2

7 NIC 10 G NICs Dual Port (Intel) Full Height 1,2 2

8 NIC 10 GBT NICs (Intel) Full Height 1,2 2

9 HBA FC8 HBAs Full Height 1,2 2

10 Internal storage BOSS Full Height 1,2,4 1

11 Internal storage BOSS2 Full height 1,2,4 1

12 NIC 1 Gb NICs Quad Port (Broadcom) Full Height 1,2,4 3

13 NIC 1 Gb NICs Quad Port (Intel) Full Height 1,2,4 3

14 NIC 1 Gb NICs Dual Port (Broadcom) Full Height 1,2,3,4 4

15 NIC 1 Gb NICs Quad Port (Intel) Full Height 1,2,4 3

Removing an expansion card

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

78 Installing and removing system components

4. Disconnect any cables connected to the expansion card.

Steps

1. If installed, disconnect the data cables from the PERC card.

2. Press the expansion card retention latch and push the latch downwards to open it.

Figure 56. Removing an expansion card

Figure 57. Removing the filler bracket

3. Hold the expansion card by its edges, and pull the card up to remove it from the expansion card connector and the system.

4. Install the filler bracket by performing the following steps:

a. Align the expansion card filler bracket with the slot on the system.

b. Push the expansion card filler bracket downwards until firmly seated.

c. Close the blue expansion card retention latch by pushing the latch up until the latch snaps into place.

NOTE: Filler brackets must be installed in empty expansion-card slots to maintain FCC certification of the system.

The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system.

Installing and removing system components 79

Next steps

1. Replace an expansion card.

2. Install the air shroud.

Installing an expansion card

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Open the expansion card retention latch.

2. Remove the existing expansion card or filler bracket from the slot.

NOTE: Store this bracket for future use. Filler brackets must be installed in empty expansion-card slots to maintain

FCC certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and

airflow inside the system.

3. Holding the card by its edges, align the card with the expansion card connector on the system board.

4. Insert the card firmly into the expansion card connector until the card is firmly seated.

5. Close the expansion card retention latch by pushing the latch down until the latch snaps into place.

Figure 58. Installing an expansion card

80 Installing and removing system components

Figure 59. Installing the filler bracket

6. Connect the data cables to the expansion card.

Next steps

1. Install the air shroud.

2. Connect the cables to the expansion card.

3. Follow the procedure listed in After working inside your system.

M.2 SSD module

Removing the M.2 SSD module

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

4. Remove the BOSS card.

NOTE: The procedure to remove the BOSS card is similar to removing an expansion card.

Steps

1. Using the Phillips #1 screwdriver, remove the screws securing the M.2 SSD module to the BOSS card.

2. Pull the M.2 SSD module to disconnect from the BOSS card connector.

Installing and removing system components 81

Figure 60. Removing the M.2 SSD module

Next steps

Replace the M.2 SSD module.

Installing the M.2 SSD module

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

4. Remove the BOSS card.

NOTE: The procedure to remove the BOSS card is similar to the removing an expansion card.

Steps

1. Align the M.2 SSD module at an angle with the BOSS card connector.

2. Insert the M.2 SSD module until it is firmly seated in the BOSS card connector.

3. Using the Phillips #1 screwdriver, secure the M.2 SSD module on the BOSS card with the screw.

82 Installing and removing system components

Figure 61. Installing the M.2 SSD module

Next steps

1. Install the BOSS card.

NOTE: The procedure to install the BOSS card is similar to removing an expansion card.

2. Install the air shroud.

3. Follow the procedure listed in the After working inside your system.

Optional IDSDM or vFlash module

The IDSDM or vFlash module combines the IDSDM and/or vFlash features into a single module.

NOTE: The write-protect switch is on the IDSDM or vFlash module.

Removing the optional IDSDM or vFlash card

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

4. If you are replacing the IDSDM/vFlash card, remove the MicroSD cards.

NOTE: Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards

into the corresponding slots.

Steps

Holding the pull tab, lift the IDSDM/vFlash card out of the system.

Next steps

NOTE: If you are replacing the IDSDM or vFlash module, remove the MicroSD cards.

1. Replace the IDSDM/vFlash module.

Installing and removing system components 83

Installing optional IDSDM or vFlash card

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions.

2. Follow the procedure listed in the Before working inside your system.

3. Remove the air shroud.

Steps

1. Locate the IDSDM/vFlash connector on the system board. To locate IDSDM/vFlash connector, see System board jumpers and

connectors section.

2. Align the IDSDM/vFlash card with the connector on the system board.

3. Push the IDSDM/vFlash card until it is firmly seated on the system board.

Figure 62. Installing optional IDSDM or vFlash card

Next steps

1. Install the MicroSD cards.

NOTE: Reinstall the MicroSD cards into the same slots that are based on the labels you had marked on the cards

during removal.

2. Install the air shroud.

3. Follow the procedure that is listed in After working inside your system.

Removing the MicroSD card

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions.

2. Follow the procedure listed in the Before working inside your system.

3. Remove the air shroud.

4. Remove the IDSDM or vFlash module.

Steps

1. Locate the MicroSD card slot on the vFlash/IDSDM module, and press the card to partially release it from the slot. To locate IDSDM/

vFlash module, see the System board jumpers and connectors section.

2. Hold the MicroSD card and remove it from the slot.

84 Installing and removing system components

NOTE: Temporarily label each MicroSD card with its corresponding slot number after removal.

Figure 63. Removing the MicroSD card

Next steps

1. Replace the MicroSD cards.

Installing the MicroSD card

Prerequisites

1. Follow the safety guidelines listed in the Safety instructions.

2. Follow the procedure listed in the Before working inside your system.

3. Remove the air shroud.

4. Remove the IDSDM or vFlash module.

NOTE: To use a MicroSD card with your system, ensure that the Internal SD Card Port is enabled in System Setup.

NOTE: If reinstalling, ensure that you install the MicroSD cards into the same slots based on the labels you had marked

on the cards during removal.

Steps

1. Locate the MicroSD card connector on the IDSDM/vFlash module. Orient the MicroSD card appropriately and insert the contact-pin

end of the card into the slot. To locate IDSDM/vFlash, see the System board jumpers and connectors section.

NOTE: The slot is keyed to ensure correct insertion of the card.

2. Press the card into the card slot to lock it into place.

Installing and removing system components 85

Figure 64. Installing the MicroSD card

Next steps

1. Install the IDSDM or vFlash module.

2. Follow the procedure listed in the After working inside your system.

Processor and heat sink

Removing the heat sink

Prerequisites

WARNING: The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to

cool before removing it.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud

Steps

1. Using a Phillips #2 screwdriver, loosen the screws on the heat sink in the order below:

a. Loosen the first screw three turns.

b. Loosen the second screw completely.

c. Return to the first screw and loosen it completely.

2. Repeat the procedure for the remaining screws.

3. Lift the heat sink from the system.

86 Installing and removing system components

Figure 65. Removing the heat sink

Next steps

1. If you are removing a faulty heat sink, Replace the heat sink. Else, remove the processor.

2. Follow the procedure listed in After working inside your system.

Removing the processor

Prerequisites

WARNING: The heat sink may be hot to touch for some time after the system has been powered down. Allow the heat

sink to cool before removing it.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the air shroud.

4. Remove the heat sink.

Steps

1. Release the socket lever by pushing the lever down and out from under the tab on the processor shield.

2. Lift the lever until the processor shield is fully open.

3. Lift the processor from the socket.

Installing and removing system components 87

Figure 66. Removing the processer

CAUTION: Do not touch the processor socket pins, they are fragile and can be permanently damaged. Be careful not

to bend the pins in the processor socket when removing the processor out of the socket.

Next steps

1. Replace the processor into the processor and heat sink.

2. Follow the procedure listed in After working inside your system.

Installing the processor

Prerequisites

Follow the safety guidelines listed in Safety instructions.

Steps

1. Align the pin1-indicator of the processor with the triangle on the system board.

CAUTION: Do not use force to seat the processor. When the processor is positioned correctly, it engages easily into

the socket.

2. Place the processor in the socket.

3. Close the processor shield by sliding it under the retention screw on the system board.

4. Lower the lever and push it under the tab to lock the processor shield.

Figure 67. Installing the processor

Next steps

1. Replace the heat sink.

2. Replace the air shroud.

3. Follow the procedure listed in After working inside your system.

88 Installing and removing system components

Installing the heat sink

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Install the processor.

Steps

1. If you are using an existing heat sink, remove the thermal grease from the heat sink by using a clean lint-free cloth.

2. Use the thermal grease syringe included with your processor kit to apply the grease in a thin spiral on the top of the processor as

shown in the following figure.

Figure 68. Applying thermal grease on top of the processor

CAUTION: Applying too much thermal grease can result in excess grease coming in contact with and contaminating

the processor socket.

NOTE: The thermal grease syringe is intended for one-time use only. Dispose of the syringe after you use it.

3. Align the screws on the heat sink with the standoffs on the system board.

CAUTION: When installing the heat sink, ensure that the airflow arrow is pointed towards the rear of the system.

4. Use a Phillips #2 screwdriver to tighten the screws to secure the heat sink to the system board.

a. Tighten the first screw three turns.

b. Tighten the screw diagonally opposite to the screw you tightened.

c. Return to the first screw and tighten it completely.

5. Repeat the procedure for the remaining screws.

Installing and removing system components 89

Figure 69. Installing the heat sink

Next steps

1. Replace the air shroud.

2. Follow the procedure listed in After working inside your system.

3. While booting, press F2 to enter System Setup and verify that the processor information matches the new system configuration.

4. Run the system diagnostics to verify that the new processor operates correctly.

Power supply unit

NOTE: For more information, see the Technical specifications section.

Removing the power supply unit blank

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

Steps

Remove the PSU blank in the bay by pulling the blank outward.

CAUTION: To ensure proper system cooling, the PSU blank must be installed in the second PSU bay in a non-redundant

configuration. Remove the PSU blank only if you are installing a second PSU.

90 Installing and removing system components

Figure 70. Removing the power supply unit blank

Next steps

Install the PSU or PSU blank.

Installing the power supply unit blank

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

NOTE: Install the power supply unit (PSU) blank only in the second PSU bay.

2. Remove the PSU.

Steps

Align the PSU blank with the PSU slot and push it into the PSU slot until it clicks into place.

Figure 71. Installing the power supply unit blank

Installing and removing system components 91

Removing a redundant AC power supply unit

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Disconnect the power cable from the power outlet and from the PSU you want to remove, then remove the cable from the strap on

the PSU handle.

Steps

Press the orange release latch and slide the PSU out of the system using the PSU handle.

Figure 72. Removing a redundant power supply unit

Next steps

Install the PSU or PSU blank.

Installing a redundant AC power supply unit

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. For systems that support redundant PSU, ensure that both the PSUs are of the same type and have the same maximum output

power.

NOTE: The maximum output power (shown in watts) is listed on the PSU label.

3. Remove the PSU blank.

Steps

Slide the PSU into the system until the PSU is fully seated.

92 Installing and removing system components

Figure 73. Installing a redundant power supply unit

Next steps

1. Connect the power cable to the PSU, and plug the cable into a power outlet.

CAUTION: When connecting the power cable to the PSU, secure the cable to the PSU with the strap.

NOTE: When installing, hot swapping, or hot adding a new PSU, wait for 15 seconds for the system to recognize the

PSU and determine its status. The PSU redundancy may not occur until discovery is complete. The PSU status

indicator turns green to indicate that the PSU is functioning properly.

Removing a cabled power supply unit

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Disconnect all the power cables of the PSU from the system board and the drive backplane.

2. Remove the screw securing the PSU to the system and slide the PSU out of the PSU bay in the chassis.

Installing and removing system components 93

Figure 74. Removing a cabled power supply unit

Next steps

1. Replace a cabled PSU.

Installing a cabled power supply unit

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Unpack the replacement power supply unit (PSU).

Steps

1. Slide the PSU into the PSU bay in the chassis until the PSU is fully seated.

2. Tighten the screw to secure the PSU to the system.

3. Connect all the power cables from the PSU to the system board and the drive backplane.

94 Installing and removing system components

Figure 75. Installing a cabled power supply unit

Next steps

1. Follow the procedure listed in After working inside your system.

Power interposer board

Removing the power interposer board

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the power supply units (PSUs).

CAUTION: To prevent damage to the power interposer board, you must remove the power supply units or PSU blank

from the system before removing the power interposer board (PIB).

Steps

1. Disconnect all cables connected from the power interposer board (PIB) to the system board, and remove the cables from the cable

retention brackets.

NOTE: Observe the routing of the cable as you remove it from the system. Route the cable properly when you

replace it to prevent the cable from being pinched or crimped.

2. Pressing the release latch on the PIB, lift the PIB to release it from the hooks on the PSU cage.

3. Lift the board and slide it out at an angle to disengage the guide pins on the board.

Installing and removing system components 95

Figure 76. Removing the power interposer board

Next steps

1. Replace the power interposer board (PIB).

Installing the power interposer board

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the power supply units.

4. Remove the air shroud.

Steps

1. Align the slots on the power interposer board (PIB) with the hooks on the power supply unit (PSU) cage and slide the PIB until it snaps

into place.

2. Route the P3 power cable through the securing clip on the system board and connect the power cable to the drive backplane.

Figure 77. Installing the power interposer board

Next steps

1. Install the air shroud

2. Replace the PSUs.

3. Follow the procedure that is listed in After working inside your system.

96 Installing and removing system components

System battery

Replacing the system battery

Prerequisites

NOTE: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same

or equivalent type that the manufacturer recommends. Discard used batteries according to the manufacturer's

instructions. See the safety instructions that came with your system for more information.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Locate the system battery on the system.

2. To remove the battery:

a. Push the battery toward the positive side of the battery until the battery disengages from the connector.

b. Lift the battery away from the system.

Figure 78. Removing the system battery

3. To install a new system battery:

a. Hold the battery with the + sign facing the positive side of the battery connector.

NOTE: Ensure that you do not push the battery clip more than 3.2 millimeters or you might risk damaging the

part.

b. Insert the battery down into the connector until the battery snaps into place.

Installing and removing system components 97

Figure 79. Installing the system battery

Next steps

1. Follow the procedure listed in After working inside your system.

2. Enter the System Setup to confirm that the battery is operating properly.

3. Enter the correct time and date in the System Setup's Time and Date fields.

4. Exit the System Setup.

5. To test the newly installed battery, remove the system from the enclosure, for at least an hour.

6. Reinstall the system into the enclosure, after an hour.

7. Enter the System Setup and if the time and date are still incorrect, see Getting help.

System board

Removing the system board

Prerequisites

CAUTION: If you are using the Trusted Platform Module (TPM) with an encryption key, you may be prompted to create

a recovery key during program or System Setup. Be sure to create and safely store this recovery key. If you replace this

system board, you must supply the recovery key when you restart your system or program before you can access the

encrypted data on your hard drives.

CAUTION: Do not attempt to remove the TPM plug-in module from the system board. Once the TPM plug-in module is

installed, it is cryptographically bound to that specific system board. Any attempt to remove an installed TPM plug-in

module breaks the cryptographic binding, and it cannot be reinstalled or installed on another system board.

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

3. Remove the following:

a. Air shroud

b. Internal cooling fan

c. Expansion cards, if installed

d. vFlash/IDSDM module

e. Internal USB key, if installed

f. Processors and heat sink

98 Installing and removing system components

CAUTION: To prevent damage to the processor pins when replacing a faulty system board, ensure that you cover

the processor socket with the processor protective cap.

g. Memory modules

Steps

1. Disconnect all cables from the system board.

CAUTION: Take care not to damage the system identification button while removing the system board from the

system.

CAUTION: Do not lift the system board by holding a memory module, processor, or other components.

2. Using a Phillips #2 screwdriver, remove the screws that secure the system board to the system.

Figure 80. Removing the screws from the system board

3. Holding the post, incline the system board at an angle, and lift the system board out of the system.

Figure 81. Removing the system board

Installing and removing system components 99

Next steps

1. Replace or install the system board.

Installing the system board

Prerequisites

Follow the safety guidelines listed in Safety instructions.

Steps

1. Unpack the new system board assembly.

CAUTION: Do not lift the system board by holding a memory module, processor, or other components.

CAUTION: Take care not to damage the system identification button while placing the system board into the system.

2. Holding the post, incline the system board, and lower the system board into the system.

3. Holding the system board holder, push the system board toward the back of the system such that the ports on the system board align

with the corresponding slots on the system.

4. Using the Phillips #2 screwdriver, secure the system board to the system with screws.

Figure 82. Installing the system board

100 Installing and removing system components

Next steps

1. Replace the following:

a. Trusted Platform Module (TPM)

NOTE: The TPM plug-in module is attached to the system board and cannot be removed. A replacement TPM

plug-in module is provided for all system board replacements, where a TPM plug-in module was installed.

b. Memory modules

c. Processors and heat sink

d. Internal USB key, if installed

e. vFlash/IDSDM module

f. Expansion cards, if installed

g. Internal cooling fan

h. Air shroud

2. Reconnect all cables to the system board.

NOTE: Ensure that the cables inside the system are routed along the chassis wall and secured by using the cable

securing bracket.

3. Follow the procedure that is listed in Safety instructions.

4. Ensure that you:

a. Use the Easy Restore feature to restore the Service Tag. For more information, see the Restoring the system using Easy Restore

section.

b. If the Service Tag is not backed up in the backup flash device, enter the Service Tag manually. For more information, see the

Manually update the Service Tag section.

c. Update the BIOS and iDRAC versions.

d. Reenable the Trusted Platform Module (TPM). For more information, see the Upgrading the Trusted Platform Module section.

5. Import your new or existing iDRAC Enterprise license.

For more information, see iDRAC User's Guide, at www.dell.com/poweredgemanuals

Restoring the system using Easy Restore

The easy restore feature enables you to restore your service tag, license, UEFI configuration, and the system configuration data after

replacing the system board. All data is backed up in a backup flash device automatically. If BIOS detects a new system board, and the

service tag in the backup flash device, BIOS prompts the user to restore the backup information.

About this task

Below is a list of options available:

• Restore the service tag, license, and diagnostics information, press Y

• Navigate to the Lifecycle Controller based restore options, press N.

• Restore data from a previously created Hardware Server Profile, press F10

NOTE: When the restore process is complete, BIOS prompts to restore the system configuration data.

• To restore the system configuration data, press Y

• To use the default configuration settings, press N

NOTE: After the restore process is complete, system reboots.

Manually update the Service Tag

After replacing a system board, if Easy Restore fails, follow this process to manually enter the Service Tag, using System Setup.

About this task

If you know the system service tag, use the System Setup menu to enter the service tag.

Steps

1. Power on the system.

2. To enter the System Setup, press F2.

3. Click Service Tag Settings.

4. Enter the service tag.

Installing and removing system components 101

NOTE: You can enter the service tag only when the Service Tag field is empty. Ensure that you enter the correct

service tag. Once the service tag is entered, it cannot be updated or changed.

5. Click OK.

Trusted Platform Module

Upgrading the Trusted Platform Module

Prerequisites

NOTE:

• Ensure that your operating system supports the version of the TPM module being installed.

• Ensure that you download and install the latest BIOS firmware on your system.

• Ensure that the BIOS is configured to enable UEFI boot mode.

About this task

CAUTION: Once the TPM plug-in module is installed, it is cryptographically bound to that specific system board. Any

attempt to remove an installed TPM plug-in module breaks the cryptographic binding, the removed TPM cannot be

reinstalled or installed on another system board.

Removing the TPM

Steps

1. Locate the TPM connector on the system board.

2. Press to hold the module down and remove the screw using the security Torx 8-bit shipped with the TPM module.

3. Slide the TPM module out from its connector.

4. Push the plastic rivet away from the TPM connector and rotate it 90° counterclockwise to release it from the system board.

5. Pull the plastic rivet out of its slot on the system board.

Installing the TPM

Steps

1. To install the TPM, align the edge connectors on the TPM with the slot on the TPM connector.

2. Insert the TPM into the TPM connector such that the plastic rivet aligns with the slot on the system board.

3. Press the plastic rivet until the rivet snaps into place.

4. Replace the screw that secures the TPM to the system board.

Figure 83. Installing the TPM

102 Installing and removing system components

Next steps

1. Replace the system board.

2. Follow the procedure listed in After working inside your system.

3. To verify if the memory module has been installed properly, press F2 and navigate to System Setup Main Menu > System BIOS >

Memory Settings. In the Memory Settings screen, the System Memory Size must reflect the updated capacity of the installed

memory.

4. If the value is incorrect, one or more of the memory modules may not be installed properly. Ensure that the memory module is firmly

seated in the memory module socket.

5. Run the system memory test in system diagnostics.

Initializing TPM for BitLocker users

Steps

1. Initialize the TPM.

For more information, see initializing the TPM for Intel TXT users.

2. The TPM Status changes to Enabled, Activated.

Initializing the TPM 1.2 for TXT users

Steps

1. While booting your system, press F2 to enter System Setup.

2. On the System Setup Main Menu screen, click System BIOS > System Security Settings.

3. From the TPM Security option, select On with Preboot Measurements.

4. From the TPM Command option, select Activate.

5. Save the settings.

6. Restart your system.

7. Enter System Setup again.

8. On the System Setup Main Menu screen, click System BIOS > System Security Settings.

9. From the Intel TXT option, select On.

Initializing the TPM 2.0 for TXT users

Steps

1. While booting your system, press F2 to enter System Setup.

2. On the System Setup Main Menu screen, click System BIOS > System Security Settings.

3. From the TPM Security option, select On.

4. Save the settings.

5. Restart your system.

6. Enter System Setup again.

7. On the System Setup Main Menu screen, click System BIOS > System Security Settings.

8. Select the TPM Advanced Settings option.

9. From the TPM2 Algorithm Selection option, select SHA256, then go back to System Security Settings screen.

10. On the System Security Settings screen, from the Intel TXT option, select On.

11. Save the settings.

12. Restart your system.

Installing and removing system components 103

Control panel

Removing the control panel assembly

Prerequisites

1. Follow the safety guidelines listed in Safety instructions.

2. Follow the procedure listed in Before working inside your system.

Steps

1. Using the Phillips #2 screwdriver, remove the screw that secures control panel to the system.

2. Disconnect the control panel cable and the control panel USB cable from the system board.

CAUTION: Do not use excessive force when removing the control panel cables as it can damage the connectors.

3. Slide the control panel out of the system.

4. To remove the information tag, perform the following steps:

a. Locate and press the tabs on the information tag.

b. Push the information tag out of the slot to remove it from the control panel.

Figure 84. Removing the control panel assembly

NOTE: Retain the information tag to replace it in the new control panel.

Next steps

1. Replace the control panel assembly.

Installing the control panel assembly

Prerequisites

Follow the safety guidelines listed in Safety instructions.

Steps

1. Replace the blank information tag in the new control panel with the information tag retained from the old control panel.

104 Installing and removing system components

2. To install the information tag, push the information tag into the control-panel slot.

3. Connect the control panel cable and the control panel USB cable to the control panel assembly.

4. Align and insert the control panel into the control panel slot in the system.

5. Secure the control panel to the system by using the screw.

6. Connect the control panel cable and the control panel USB cable to the system board.

Figure 85. Installing the control panel assembly

Next steps

1. Follow the procedure listed in After working inside your system.

Installing and removing system components 105

PowerEdge T340 jumpers and connectors

This topic provides specific information about the jumpers. It also provides some basic information about jumpers and switches and

describes the connectors on the various boards in the system. Jumpers on the system board help to disable the system and setup

passwords. You must know the connectors on the system board to install components and cables correctly.

Topics:

•System board jumpers and connectors

•System board jumper settings

•Disabling forgotten password

System board jumpers and connectors

Figure 86. T340 system board jumpers and connectors

106 PowerEdge T340 jumpers and connectors

Table 10. System board connectors

Item Connector Description

1 FP_USB Front panel USB connector

2 PIB_CONN Power interposer board signal connector

3 BP_SIG Backplane signal connector

4 Slot 1 PCIE_G3_X8 CPU PCIe card connector 1

5 Slot 2 PCIE_G3_X8 CPU PCIe card connector 2

6 Slot 3 PCIE_G3_X1 PCH PCIe card connector 3

7 LEDs (7) System board diagnostic LED indicators

8 INT_USB_3.0 Internal USB

9 Slot 4 PCIE_G3_X4 PCH PCIe card connector 4

10 T_INTRUSION Intrusion switch connector

11 SYS_FAN Fan

12 P2 CPU power connector P2

13 A1, A2, A3, A4 Memory module sockets

14 P1 System power P1

15 SATA 0-3 Mini SAS connector

16 SATA_ODD/SSD Optical disk drive connector

17 PWR_EVNT Power event

18 J_SATA_2 SATA connector 2

19 CPU Processor

20 NVRAM_CLR NVRAM password Jumper

21 TPM Trusted Platform Module connector

22 PWRD_EN Reset BIOS password jumper

23 IDSDM+ vFlash IDSDM+VFlash connector

24 Coin cell battery Coin cell battery

25 CTRL_PNL Control panel

System board jumper settings

For information on resetting the password jumper to disable a password, see the Disabling a forgotten password section.

Disabling forgotten password

The software security features of the system include a system password and a setup password. The password jumper enables or disables

password features and clears any password(s) currently in use.

Prerequisites

CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and

simple repairs as authorized in your product documentation, or as directed by the online or telephone service and

support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow

the safety instructions that are shipped with your product.

PowerEdge T340 jumpers and connectors 107

Steps

1. Power off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

2. Remove the system cover.

3. Move the jumper on the system board jumper from pins 2 and 4 to pins 4 and 6.

4. Install the system cover.

The existing passwords are not disabled (erased) until the system boots with the jumper on pins 4 and 6. However, before you assign

a new system and/or setup password, you must move the jumper back to pins 2 and 4.

NOTE: If you assign a new system and/or setup password with the jumper on pins 4 and 6, the system disables the

new password(s) the next time it boots.

5. Reconnect the system to its electrical outlet and power on the system, including any attached peripherals.

6. Power off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

7. Remove the system cover.

8. Move the jumper on the system board jumper from pins 4 and 6 to pins 2 and 4.

9. Install the system cover.

10. Reconnect the system to its electrical outlet and power on the system, including any attached peripherals.

11. Assign a new system and/or setup password.

108 PowerEdge T340 jumpers and connectors

Technical specifications

The technical and environmental specifications of your system are outlined in this section.

Topics:

•Chassis dimensions

•System weight

•Processor specifications

•Supported operating systems

•PSU specifications

•Cooling fan specifications

•System battery specifications

•Expansion card specifications

•Memory specifications

•Storage controller specifications

•Drive specifications

•Ports and connectors specifications

•Video specifications

•Environmental specifications

Chassis dimensions

Figure 87. Chassis dimensions

Technical specifications 109

Table 11. Dell EMC PowerEdge T340 chassis dimensions

Xa Xb Ya Yb Yc Za Zb Zc

218 mm (8.58

inches)

307.9 mm

(12.12 inches)

430.3 mm

(16.94 inches)

443.3 mm

(17.45 inches)

471.3 mm

(18.56 inches) With bezel: 14.1

mm (0.56

inches)

545.4 mm

(21.47 inches)

589.1 mm

(23.19 inches)

System weight

Table 12. Dell EMC PowerEdge T340 system chassis weight

System configuration Maximum weight (with all drives/SSDs)

8 x 3.5-inch drives 26 Kg (57.32 lb)

Processor specifications

Table 13. Dell EMC PowerEdge T340 processor specifications

Supported processor Number of processors supported

Intel Xeon processor E-2200 product family

Intel Core i3 9100 processor

Intel Pentium G5420 processor

Intel Celeron G4930 processor

Intel Xeon processor E-2100 product family

Intel Core i3 8100 processor

Intel Pentium G5500 processor

Intel Celeron G4900 processor

One

Supported operating systems

The Dell EMC PowerEdge T340 supports the following operating systems:

• Canonical Ubuntu LTS

• Citrix Hypervisor

• Microsoft Windows Server

• Red Hat Enterprise Linux

• SUSE Linux Enterprise Server

• VMware ESXi

NOTE: For more information, go to www.dell.com/ossupport.

PSU specifications

The Dell EMC PowerEdge T340 system supports up to two AC power supply units (PSUs).

110 Technical specifications

Table 14. Dell EMC PowerEdge T340 PSU specifications

PSU Class Heat

dissipation

(maximum)

Frequency Voltage AC DC Current

High line

(100–240

Low line

(100–120

495 W AC Platinum 1908 BTU/hr 50/60 Hz 100–240 V

AC,

autoranging

495 W NA N/A 6.5 A–3 A

350 W AC Bronze 1455 BTU/hr 50/60 Hz 100–240 V

AC,

autoranging

350 W NA N/A 5.5 A–3 A

Cooling fan specifications

The Dell EMC PowerEdge T340 system supports one system cooling fan.

NOTE: When selecting or upgrading the system configuration, to ensure optimum power utilization, verify the system

power consumption with the Dell Energy Smart Solution Advisor available at Dell.com/ESSA.

System battery specifications

The Dell EMC PowerEdge T340 system supports CR 2032 3.0-V lithium coin cell system battery.

Expansion card specifications

The Dell EMC PowerEdge T340 system supports up to four PCI express (PCIe) Generation 3.

Table 15. Expansion card slots supported on the system board

PCIe slot Processor Connection PCIe slot height PCIe slot length Slot width

Slot 1 (Gen3) Processor Full Height Half Length x8 link in x8 slot

Slot 2 (Gen3) Processor Full Height Half Length x8 link in x16 slot

Slot 3 (Gen3) Platform Controller Hub Full Height Half Length x1

Slot 4 (Gen3) Platform Controller Hub Full Height Half Length x4 link in x8 slot

NOTE: The expansion cards are not hot swappable.

Memory specifications

The Dell EMC PowerEdge T340 system supports the following memory specifications for optimized operation:

Table 16. Memory specifications

DIMM type DIMM rank DIMM capacity Minimum RAM Maximum RAM

UDIMM

Single rank 8 GB 8 GB 32 GB

16 GB 16 GB 64 GB

Dual rank 8 GB 8 GB 32 GB

16 GB 16 GB 64 GB

Technical specifications 111

Table 16. Memory specifications

Memory module sockets Speed

Four 288-pin 2666 MT/s

2400 MT/s

2133 MT/s

Storage controller specifications

The Dell EMC PowerEdge T340 system supports the following controller cards:

Table 17. Dell EMC PowerEdge T340 system controller cards

Internal controllers External controllers

• PERC H730P

• PERC H330

• S140

• HBA330

• 12Gbps SAS Ext. HBA

Drive specifications

Drives

The Dell EMC PowerEdge T340 system supports:

• 4 x 3.5-inch SAS, SATA drives, 2.5-inch hotplug drives

• 8 x 3.5-inch SAS, SATA drives, 2.5-inch hotplug drives

NOTE: 2.5-inch drives in 3.5-inch carriers are supported for SAS, and SATA SSD drives.

Optical drives

The Dell EMC PowerEdge T340 system supports the following optical drives.

Table 18. Supported optical drive type

Supported drive type Supported number of drives

Dedicated SATA DVD-ROM drive or DVD +/-RW drive One

Tape drives

The Dell EMC PowerEdge T340 system supports up to two dedicated 5.25-inch tape drives.

Ports and connectors specifications

USB ports specifications

Table 19. Dell EMC PowerEdge T340 system USB port specifications

Front panel Back panel Internal USB

• One USB 3.0-compliant port • Two USB 3.0-compliant ports • One internal USB 3.0-compliant port

112 Technical specifications

Table 19. Dell EMC PowerEdge T340 system USB port specifications

Front panel Back panel Internal USB

• One iDRAC USB MGMT port (USB

2.0)

NOTE: The micro USB 2.0

compliant port can only be

used as an iDRAC Direct or a

management port.

• Four USB 2.0-compliant ports

NIC ports specifications

The Dell EMC PowerEdge T340 system supports up to two 10/100/1000 Mbps Network Interface Controller (NIC) ports that are located

on the back panel.

Serial connector specifications

The Dell EMC PowerEdge T340 system supports one serial connector on the back panel, which is a 9-pin connector, Data Terminal

Equipment (DTE), 16550-compliant.

VGA ports specification

The Dell EMC PowerEdge T340 system supports one 15-pin VGA port, on the back of the system.

IDSDM module

The Dell EMC PowerEdge T340 system supports optional Internal Dual SD module (IDSDM) module.

The module supports three microSD cards; two cards for IDSDM and one card for vFlash. In 14th generation of PowerEdge servers, the

IDSDM or vFlash module is combined into a single card module, and is available in the following configurations:

• vFlash or

• vFlash and IDSDM

Table 20. Supported microSD card storage capacity

IDSDM card vFlash card

• 16 GB

• 32 GB

• 64 GB

• 16 GB

NOTE: There are two dip switches on the IDSDM or vFlash module for write-protection.

NOTE: One IDSDM card slot is dedicated for redundancy.

NOTE: Use Dell EMC branded microSD cards that are associated with the IDSDM or vFlash configured systems.

Video specifications

The Dell EMC PowerEdge T340 system supports Matrox G200eR2 graphics card with 16 MB capacity.

Table 21. Supported video resolution options

Resolution Refresh rate Color depth (bits)

640x480 60, 70 8, 16, 24

Technical specifications 113

Table 21. Supported video resolution options(continued)

Resolution Refresh rate Color depth (bits)

800x600 60, 75, 85 8, 16, 24

1024x768 60, 75, 85 8, 16, 24

1152x864 60, 75, 85 8, 16, 24

1280x1024 60, 75 8, 16, 24

Environmental specifications

NOTE: For additional information about environmental certifications, refer to the

Product Environmental Datasheet

located with the Manuals & Documents on www.dell.com/support/home.

Table 22. Temperature specifications

Temperature Specifications

Storage -40–65°C (-40–149°F)

Continuous operation (for altitude less than 950 m

or 3117 ft)

10–35°C (50–95°F) with no direct sunlight on the equipment

Fresh air For information about fresh air, see the Expanded operating temperature section.

Maximum temperature gradient (operating and

storage)

20°C/h (68°F/h)

Table 23. Relative humidity specifications

Relative humidity Specifications

Storage 5% to 95% RH with 33°C (91°F) maximum dew point.

Atmosphere must be noncondensing at all times.

Operating 10% to 80% RH with 29°C (84.2°F) maximum dew point.

Table 24. Maximum vibration specifications

Maximum vibration Specifications

Operating 0.26 Grms at 5 Hz to 350 Hz (all operation orientations)

Storage 1.88 Grms at 10 Hz to 500 Hz for 15 minutes (all six sides tested)

Table 25. Maximum shock pulse specifications

Maximum shock pulse Specifications

Operating Six consecutively executed shock pulses in the positive and negative x, y, and z

axis of 6 G for up to 11 ms.

Storage Six consecutively executed shock pulses in the positive and negative x, y, and z

axis (one pulse on each side of the system) of 71 G for up to 2 ms.

Table 26. Maximum altitude specifications

Maximum altitude Specifications

Operating 3048 m (10,000 ft)

Storage 12,000 m (39,370 ft)

114 Technical specifications

Table 27. Operating temperature derating specifications

Operating temperature derating Specifications

Up to 35°C (95°F) Maximum temperature is reduced by 1°C/300 m (1°F/547 ft), above 950 m

(3,117 ft).

35–40°C (95–104°F) Maximum temperature is reduced by 1°C/175 m (1°F/319 ft), above 950 m

(3,117 ft).

40–45°C (104–113°F) Maximum temperature is reduced by 1°C/125 m (1°F/228 ft), above 950 m

(3,117 ft).

Standard operating temperature

Table 28. Standard operating temperature specifications

Standard operating temperature Specifications

Continuous operation (for altitude less than 950 m or 3117

ft)

10–35°C (50–95°F) with no direct sunlight on the equipment.

Expanded operating temperature

Table 29. Expanded operating temperature specifications

Expanded operating temperature Specifications

Continuous operation 5°C–40°C at 5% to 85% RH with 29°C dew point.

NOTE: Outside the standard operating temperature

(10°C–35°C), the system can operate continuously in

temperatures as low as 5°C and as high as 40°C.

For temperatures 35°C– 40°C, derate maximum allowable

temperature by 1°C per 175 m (1°F per 319 ft) above 950 m

(3,1171 ft).

≤ 1% of annual operating hours -5°C–45°C at 5% to 90% RH with 29°C dew point.

NOTE: Outside the standard operating temperature

(10°C–35°C), the system can operate down to -5°C or

up to 45°C for a maximum of 1% of its annual operating

hours.

For temperatures 40°C– 45°C, derate maximum allowable

temperature by 1°C per 125 m (1°F per 228 ft) above 950 m (3.117

ft).

NOTE: When operating in the expanded temperature range, the performance of the system may be impacted.

NOTE: When operating in the expanded temperature range, ambient temperature warnings may be reported on the

System Event Log.

Expanded operating temperature restrictions

• Do not perform a cold startup of the system below 5°C.

• The operating temperature specified is for a maximum altitude of 950 m for Fresh Air cooling.

• Two redundant power supply units are required.

• Cooling redundancy is not supported due to single fan only in system.

• Support up to 80 W processor.

• One system fan is required.

• Non-Dell qualified peripheral cards and/or peripheral cards greater than 25 W are not supported.

• GPU is not supported.

Technical specifications 115

• Tape backup unit is supported.

Particulate and gaseous contamination specifications

The following table defines the limitations that help avoid any damages to the IT equipment and/or, or both failure from particulate and

gaseous contamination. If the levels of particulate or gaseous pollution exceed the specified limitations and results in equipment damage or

failure, you must rectify the environmental conditions. Remediation of environmental conditions is the responsibility of the customer.

Table 30. Particulate contamination specifications

Particulate contamination Specifications

Air filtration Data center air filtration as defined by ISO Class 8 per ISO 14644-1

with a 95% upper confidence limit.

NOTE: This condition applies to data center

environments only. Air filtration requirements do not

apply to IT equipment designed to be used outside a

data center, in environments such as an office or factory

floor.

NOTE: Air entering the data center must have MERV11

or MERV13 filtration.

Conductive dust Air must be free of conductive dust, zinc whiskers, or other

conductive particles.

NOTE: This condition applies to data center and non-

data center environments.

Corrosive dust • Air must be free of corrosive dust.

• Residual dust present in the air must have a deliquescent point

less than 60% relative humidity.

NOTE: This condition applies to data center and non-

data center environments.

Table 31. Gaseous contamination specifications

Gaseous contamination Specifications

Copper Coupon Corrosion <300 Å/month per Class G1 as defined by ANSI/ISA71.04-1985.

Silver Coupon Corrosion <200 Å/month as defined by AHSRAE TC9.9.

NOTE: Maximum corrosive contaminant levels measured at ≤50% relative humidity.

116 Technical specifications

System diagnostics and indicator codes

The diagnostic indicators on the system front panel display system status during system startup.

Topics:

•System health and system ID indicator codes

•iDRAC Direct LED indicator codes

•NIC indicator codes

•Non-redundant cabled power supply unit indicator codes

•Power supply unit indicator codes

•Drive indicator codes

•PowerEdge T340 system diagnostics

System health and system ID indicator codes

The system health and system ID indicator is located on the front panel of your system.

Figure 88. System health and system ID indicator

Table 32. System health and system ID indicator codes

System health and system ID

indicator code

Condition

Solid blue Indicates that the system is turned on, system is healthy, and system ID mode is not active.

Press the system health and system ID button to switch to system ID mode.

Blinking blue Indicates that the system ID mode is active. Press the system health and system ID button to

switch to system health mode.

Solid amber Indicates that the system is in fail-safe mode. If the problem persists, see the Getting help

section.

Blinking amber Indicates that the system is experiencing a fault. Check the System Event Log for specific

error messages. For information about the event and error messages generated by the

system firmware and agents that monitor system components, see the Error Code Lookup

page at qrl.dell.com

iDRAC Direct LED indicator codes

The iDRAC Direct LED indicator lights up to indicate that the port is connected and is being used as a part of the iDRAC subsystem.

You can configure iDRAC Direct by using a USB to micro USB (type AB) cable, which you can connect to your laptop or tablet. The

following table describes iDRAC Direct activity when the iDRAC Direct port is active:

Table 33. iDRAC Direct LED indicator codes

iDRAC Direct LED

indicator code

Condition

Solid green for two seconds Indicates that the laptop or tablet is connected.

Flashing green (on for two

seconds and off for two

seconds)

Indicates that the laptop or tablet connected is recognized.

System diagnostics and indicator codes 117

Table 33. iDRAC Direct LED indicator codes(continued)

iDRAC Direct LED

indicator code

Condition

Powers off Indicates that the laptop or tablet is unplugged.

NIC indicator codes

Each NIC on the back of the system has indicators that provide information about the activity and link status. The activity LED indicator

indicates if data is flowing through the NIC, and the link LED indicator indicates the speed of the connected network.

Figure 89. NIC indicator codes

1. Link LED indicator

2. Activity LED indicator

Table 34. NIC indicator codes

Status Condition

Link and activity indicators are off. The NIC is not connected to the network.

Link indicator is green, and activity indicator is blinking

green.

The NIC is connected to a valid network at its maximum port speed, and

data is being sent or received.

Link indicator is amber, and activity indicator is blinking

green.

The NIC is connected to a valid network at less than its maximum port

speed, and data is being sent or received.

Link indicator is green, and activity indicator is off. The NIC is connected to a valid network at its maximum port speed, and

data is not being sent or received.

Link indicator is amber, and activity indicator is off. The NIC is connected to a valid network at less than its maximum port

speed, and data is not being sent or received.

Link indicator is blinking green, and activity is off. NIC identify is enabled through the NIC configuration utility.

Non-redundant cabled power supply unit indicator

codes

Press the self-diagnostic button to perform a quick health check on the non-redundant cabled power supply unit (PSU) of the system.

118 System diagnostics and indicator codes

Figure 90. Non-redundant cabled AC PSU status indicator and self-diagnostic button

1. Self-diagnostic button

2. AC PSU status indicator

Table 35. Non-redundant AC PSU status indicator

Power Indicator Pattern Condition

Not lit Power is not connected or PSU is faulty.

Green A valid power source is connected to the PSU and the PSU is operational.

Power supply unit indicator codes

AC power supply units (PSUs) have an illuminated translucent handle that serves as an indicator. The indicator shows whether power is

present or if a power fault has occurred.

Figure 91. AC PSU status indicator

1. AC PSU status indicator/handle

Table 36. AC PSU status indicator codes

Power indicator codes Condition

Green A valid power source is connected to the PSU and the PSU is operational.

Blinking amber Indicates a problem with the PSU.

Not illuminated Power is not connected to the PSU.

Blinking green When the firmware of the PSU is being updated, the PSU handle blinks green.

CAUTION: Do not disconnect the power cord or unplug the PSU when updating firmware. If

firmware update is interrupted, the PSUs do not function.

Blinking green and turns off When hot-plugging a PSU, the PSU handle blinks green five times at a rate of 4 Hz and turns off. This

indicates a PSU mismatch with respect to efficiency, feature set, health status, or supported voltage.

CAUTION: If two PSUs are installed, both the PSUs must have the same type of label; for

example, Extended Power Performance (EPP) label. Mixing PSUs from previous generations

System diagnostics and indicator codes 119

Table 36. AC PSU status indicator codes(continued)

Power indicator codes Condition

of PowerEdge servers is not supported, even if the PSUs have the same power rating. This

results in a PSU mismatch condition or failure to power on the system.

CAUTION: When correcting a PSU mismatch, replace only the PSU with the blinking

indicator. Swapping the PSU to make a matched pair can result in an error condition and

unexpected system shutdown. To change from a high output configuration to a low output

configuration or vice versa, you must power off the system.

CAUTION: AC PSUs support both 240 V and 120 V input voltages with the exception of

Titanium PSUs, which support only 240 V. When two identical PSUs receive different input

voltages, they can output different wattages, and trigger a mismatch.

CAUTION: If two PSUs are used, they must be of the same type and have the same

maximum output power.

Drive indicator codes

The LEDs on the drive carrier indicates the state of each drive. Each drive carrier in your system has two LEDs: an activity LED (green)

and a status LED (bicolor, green/amber). The activity LED flashes whenever the drive is accessed.

Figure 92. Drive indicators on the drive and the mid drive tray backplane

1. Drive activity LED indicator

2. Drive status LED indicator

3. Drive Capacity Label

NOTE: If the drive is in the Advanced Host Controller Interface (AHCI) mode, the status LED indicator does not turn on.

Table 37. Drive indicator codes

Drive status indicator code Condition

Flashes green twice per second Identifying drive or preparing for removal.

Off Drive ready for removal.

NOTE: The drive status indicator remains off until all drives

are initialized after the system is turned on. Drives are not

ready for removal during this time.

Flashes green, amber, and then turns off Predicted drive failure.

120 System diagnostics and indicator codes

Table 37. Drive indicator codes(continued)

Drive status indicator code Condition

Flashes amber four times per second Drive failed.

Flashes green slowly Drive rebuilding.

Solid green Drive online.

Flashes green for three seconds, amber for three seconds,

and then turns off after six seconds

Rebuild stopped.

PowerEdge T340 system diagnostics

If you experience a problem with your system, run the system diagnostics before contacting Dell for technical assistance. The purpose of

running system diagnostics is to test your system hardware without using additional equipment or risking data loss. If you are unable to fix

the problem yourself, service and support personnel can use the diagnostics results to help you solve the problem.

Dell Embedded System Diagnostics

NOTE: The Dell Embedded System Diagnostics is also known as Enhanced Pre-boot System Assessment (ePSA)

diagnostics.

The Embedded System Diagnostics provides a set of options for particular device groups or devices allowing you to:

• Run tests automatically or in an interactive mode

• Repeat tests

• Display or save test results

• Run thorough tests to introduce additional test options to provide extra information about the failed device(s)

• View status messages that inform you if tests are completed successfully

• View error messages that inform you of problems encountered during testing

Running the Embedded System Diagnostics from Boot Manager

Run the Embedded System Diagnostics (ePSA) if your system does not boot.

Steps

1. When the system is booting, press F11.

2. Use the up arrow and down arrow keys to select System Utilities > Launch Diagnostics.

3. Alternatively, when the system is booting, press F10, select Hardware Diagnostics > Run Hardware Diagnostics.

The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics starts

executing the tests on all the detected devices.

Results

Running the Embedded System Diagnostics from the Dell Lifecycle

Controller

Steps

1. As the system boots, press F10.

2. Select Hardware Diagnostics → Run Hardware Diagnostics.

The ePSA Pre-boot System Assessment window is displayed, listing all devices detected in the system. The diagnostics starts

executing the tests on all the detected devices.

System diagnostics and indicator codes 121

System diagnostic controls

Menu Description

Configuration Displays the configuration and status information of all detected devices.

Results Displays the results of all tests that are run.

System health Provides the current overview of the system performance.

Event log Displays a time-stamped log of the results of all tests run on the system. This is displayed if at least one event

description is recorded.

122 System diagnostics and indicator codes

Getting help

Topics:

•Recycling or End-of-Life service information

•Contacting Dell

•Accessing system information by using QRL

•Receiving automated support with SupportAssist

Recycling or End-of-Life service information

Take back and recycling services are offered for this product in certain countries. If you want to dispose of system components, visit

www.dell.com/recyclingworldwide and select the relevant country.

Contacting Dell

Dell provides several online and telephone based support and service options. If you do not have an active internet connection, you can

find contact information about your purchase invoice, packing slip, bill, or Dell product catalog. Availability varies by country and product,

and some services may not be available in your area. To contact Dell for sales, technical assistance, or customer service issues:

Steps

1. Go to www.dell.com/support/home

2. Select your country from the drop-down menu on the lower right corner of the page.

3. For customized support:

a. Enter your system Service Tag in the Enter your Service Tag field.

b. Click Submit.

The support page that lists the various support categories is displayed.

4. For general support:

a. Select your product category.

b. Select your product segment.

c. Select your product.

The support page that lists the various support categories is displayed.

5. For contact details of Dell Global Technical Support:

a. Click Global Technical Support

b. The Contact Technical Support page is displayed with details to call, chat, or e-mail the Dell Global Technical Support team.

Accessing system information by using QRL

You can use the Quick Resource Locator (QRL) located on the information tag in the front of the T340, to access the information about

the Dell EMC PowerEdge T340.

Prerequisites

Ensure that your smartphone or tablet has the QR code scanner installed.

The QRL includes the following information about your system:

• How-to videos

• Reference materials, including the Installtion and Service Manual, and mechanical overview

• Your system service tag to quickly access your specific hardware configuration and warranty information

• A direct link to Dell to contact technical assistance and sales teams

Getting help 123

Steps

1. Go to www.dell.com/qrl and navigate to your specific product or

2. Use your smartphone or tablet to scan the model-specific Quick Resource (QR) code on your system or in the Quick Resource

Locator section.

Quick Resource Locator for Dell EMC PowerEdge T340

system

Figure 93. Quick Resource Locator for Dell EMC PowerEdge T340 system

Receiving automated support with SupportAssist

Dell EMC SupportAssist is an optional Dell EMC Services offering that automates technical support for your Dell EMC server, storage, and

networking devices. By installing and setting up a SupportAssist application in your IT environment, you can receive the following benefits:

•Automated issue detection — SupportAssist monitors your Dell EMC devices and automatically detects hardware issues, both

proactively and predictively.

•Automated case creation — When an issue is detected, SupportAssist automatically opens a support case with Dell EMC Technical

Support.

•Automated diagnostic collection — SupportAssist automatically collects system state information from your devices and uploads it

securely to Dell EMC. This information is used by Dell EMC Technical Support to troubleshoot the issue.

•Proactive contact — A Dell EMC Technical Support agent contacts you about the support case and helps you resolve the issue.

The available benefits vary depending on the Dell EMC Service entitlement purchased for your device. For more information about

SupportAssist, go to www.dell.com/supportassist.

124 Getting help

Documentation resources

This section provides information about the documentation resources for your system.

To view the document that is listed in the documentation resources table:

• From the Dell EMC support site:

1. Click the documentation link that is provided in the Location column in the table.

2. Click the required product or product version.

NOTE: To locate the product name and model, see the front of your system.

3. On the Product Support page, click Manuals & documents.

• Using search engines:

○Type the name and version of the document in the search box.

Table 38. Additional documentation resources for your system

Task Document Location

Setting up your system For more information about installing and securing

the system into a rack, see the Rail Installation

Guide included with your rack solution.

For information about setting up your system, see

the Getting Started Guide document that is

shipped with your system.

www.dell.com/poweredgemanuals

Configuring your system For information about the iDRAC features,

configuring and logging in to iDRAC, and managing

your system remotely, see the Integrated Dell

Remote Access Controller User's Guide.

For information about understanding Remote

Access Controller Admin (RACADM)

subcommands and supported RACADM

interfaces, see the RACADM CLI Guide for iDRAC.

For information about Redfish and its protocol,

supported schema, and Redfish Eventing are

implemented in iDRAC, see the Redfish API Guide.

For information about iDRAC property database

group and object descriptions, see the Attribute

Registry Guide.

www.dell.com/poweredgemanuals

For information about earlier versions of the

iDRAC documents, see the iDRAC documentation.

To identify the version of iDRAC available on your

system, on the iDRAC web interface, click ? >

About.

www.dell.com/idracmanuals

For information about installing the operating

system, see the operating system documentation.

www.dell.com/operatingsystemmanuals

For information about updating drivers and

firmware, see the Methods to download firmware

and drivers section in this document.

www.dell.com/support/drivers

Managing your system For information about systems management

software offered by Dell, see the Dell

www.dell.com/poweredgemanuals

Documentation resources 125

Table 38. Additional documentation resources for your system(continued)

Task Document Location

OpenManage Systems Management Overview

Guide.

For information about setting up, using, and

troubleshooting OpenManage, see the Dell

OpenManage Server Administrator User’s Guide.

www.dell.com/openmanagemanuals >

OpenManage Server Administrator

For information about installing, using, and

troubleshooting Dell OpenManage Essentials, see

the Dell OpenManage Essentials User’s Guide.

www.dell.com/openmanagemanuals >

OpenManage Essentials

For information about installing, using, and

troubleshooting Dell OpenManage Enterprise, see

the Dell OpenManage Enterprise User’s Guide.

www.dell.com/openmanagemanuals >

OpenManage Enterprise

For information about installing and using Dell

SupportAssist, see the Dell EMC SupportAssist

Enterprise User’s Guide.

www.dell.com/serviceabilitytools

For information about partner programs enterprise

systems management, see the OpenManage

Connections Enterprise Systems Management

documents.

www.dell.com/openmanagemanuals

Working with the Dell

PowerEdge RAID controllers

For information about understanding the features

of the Dell PowerEdge RAID controllers (PERC),

Software RAID controllers, or BOSS card and

deploying the cards, see the Storage controller

documentation.

www.dell.com/storagecontrollermanuals

Understanding event and error

messages

For information about the event and error

messages that are generated by the system

firmware and agents that monitor system

components, see the Error Code Lookup.

www.dell.com/qrl

Troubleshooting your system For information about identifying and

troubleshooting the PowerEdge server issues, see

the Server Troubleshooting Guide.

www.dell.com/poweredgemanuals

126 Documentation resources

Table of Contents

DELL T340 User Manual

Related Manuals