Table of Contents
- Read this first
- Contents
- Figures
- Tables
- Safety and environmental notices
- Preface
- Chapter 1. Product description
- Front panel
- Cartridge magazine
- Rear panel
- Bar code reader
- SAS host interface
- Encryption
- Supported Internet Protocols
- Simple Network Management Protocol (SNMP) messaging
- Network Time Protocol
- Ultrium tape drives
- Media
- Logical Unit Number (LUN) scanning
- Location coordinates and element addresses
- Library specifications
- Product environment
- Supported device drivers
- Chapter 2. User interfaces
- Chapter 3. Installation and configuration
- Choosing a location
- Installing in a rack
- Removing the accessor locking screw
- Attaching the library to a server
- Configuring the library
- Populating the library with cartridges
- Verifying library and drive operation
- Taking the Library Online
- Registering for support notification
- Chapter 4. Operations
- Chapter 5. Media
- Chapter 6. Troubleshooting
- Chapter 7. Service procedures
- Chapter 8. Removal and replacement procedures
- Error codes
- TapeAlert flags
- Sense data
- Library Configuration Form
- Accessibility
- Glossary
- Index
DELL TL1000 User Manual
Displayed below is the user manual for TL1000 by DELL which is a product in the Backup Storage Devices category. This manual has pages.
Related Manuals
Dell PowerVault TL1000 Tape Autoloader
User's Guide
Dell PowerVault TL1000 Tape Autoloader
User's Guide
ii Dell PowerVault TL1000 Tape Autoloader: User's Guide
Information in this document is subject to change without notice.
© 2015 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell
Inc. is strictly forbidden. Trademarks used in this text: Dell, the DELL logo and
PowerVault are trademarks of Dell Inc.
Other trademarks and trade names might be used in this document to refer to
either the entities claiming the marks and names or their products. Dell Inc.
disclaims any proprietary interest in trademarks and trade names other than its
own.
Type: 3572 Model: S3H/S4H/S5H/S6H/S7H
Printed October 2015
iii
iv Dell PowerVault TL1000 Tape Autoloader: User's Guide
Read this first
Contacting Dell
For customers in the United States, call 800-WWW-DELL (800-999-3355).
Note: If you do not have an active Internet connection, you can find contact
information about your purchase invoice, packing slip, bill, or Dell product catalog.
Dell provides online and telephone-based support and service options. Service
availability varies by country and product, and some services might not be
available in your area. To contact Dell for sales, technical support, or customer
service issues follow the steps that are listed:
1. Visit www.Dell.com/support.
2. Verify your country or region in the Choose A Country/Region menu at the
bottom of the page.
3. Click Contact Us on the left side of the page.
4. Select the appropriate service or support link that is based on your need.
5. Choose the method of contacting Dell that is convenient for you.
v
vi Dell PowerVault TL1000 Tape Autoloader: User's Guide
Contents
iii
Read this first ............ v
Contacting Dell ............. v
Figures ............... ix
Tables ............... xi
Safety and environmental notices ... xiii
Safety notices ............. xiii
Laser safety and compliance ........ xiv
Performing the safety inspection procedure ... xiv
Rack safety .............. xv
Preface .............. xvii
Chapter 1. Product description ..... 1
Front panel ............... 2
Cartridge magazine ............ 4
Rear panel ............... 5
Bar code reader ............. 6
SAS host interface ............ 6
Encryption ............... 6
Supported Internet Protocols ......... 7
Simple Network Management Protocol (SNMP)
messaging ............... 7
Network Time Protocol ........... 7
Ultrium tape drives ............ 8
Media ................ 8
Logical Unit Number (LUN) scanning ...... 9
Location coordinates and element addresses .... 9
Library specifications ........... 10
Product environment ........... 11
Supported device drivers .......... 12
Chapter 2. User interfaces ...... 13
Operator Panel ............. 13
Web User Interface ............ 17
Chapter 3. Installation and
configuration ............ 21
Choosing a location ........... 21
Installing in a rack ............ 22
Removing the accessor locking screw...... 27
Attaching the library to a server ....... 28
Configuring the library .......... 30
Configuring your library with the Web User
Interface .............. 31
Configuring your library with the Operator Panel 47
Populating the library with cartridges ..... 50
Verifying library and drive operation ...... 51
Taking the Library Online ......... 52
Registering for support notification ...... 52
Chapter 4. Operations ........ 55
The Operator Panel............ 56
Monitoring the library .......... 57
Managing the library .......... 58
Configuring the library ......... 62
Servicing the library .......... 67
The Web User Interface .......... 69
Monitoring the library .......... 70
Managing the library .......... 73
Configuring the library ......... 76
Servicing the library .......... 89
Chapter 5. Media .......... 97
Data cartridges ............. 98
Cartridge compatibility ......... 99
Write once, read many (WORM) cartridges ... 100
WORM media ............ 100
Data security on WORM media ...... 100
WORM media errors .......... 100
Requirements for WORM capability ..... 100
Cleaning cartridge............ 101
Bar code labels ............. 101
Guidelines for the use of bar code labels ... 102
Write-Protect switch ........... 103
Cartridge care and handling ........ 103
Provide training ........... 104
Ensure proper packaging ........ 104
Provide proper acclimation and environmental
conditions ............. 104
Perform a thorough inspection ...... 105
Handle the cartridge carefully ....... 105
Examples of cartridge problems ...... 106
Environmental and shipping specifications for tape
cartridges .............. 106
Chapter 6. Troubleshooting ..... 109
How the library reports problems ...... 109
Library error message content ........ 110
Diagnosing a problem .......... 111
Isolating problems............ 114
Installation and configuration problems .... 116
Interpreting front panel LEDs ........ 116
Reseating cables ............ 118
Emailing logs ............. 118
Chapter 7. Service procedures .... 119
ITDT-SE ............... 119
Contacting Dell technical support....... 119
Chapter 8. Removal and replacement
procedures ............ 121
Required tools ............. 121
vii
Replacing a defective cartridge magazine .... 121
Unlocking the cartridge magazine manually ... 121
Error codes ............ 123
Library error codes ........... 123
Drive error codes ............ 133
Web User Interface error messages ...... 133
Trap definitions (types) .......... 136
TapeAlert flags........... 137
TapeAlert flags supported by the library .... 137
TapeAlert flags supported by the Ultrium tape
drive ................ 139
Sense data ............ 143
Sense Key definitions........... 143
Library sense data............ 143
Tape drive sense data .......... 145
Library Configuration Form ..... 153
Accessibility............ 157
Glossary ............. 159
Index ............... 179
viii Dell PowerVault TL1000 Tape Autoloader: User's Guide
Figures
1. TL1000 Tape Autoloader ........ 1
2. Front panel components......... 2
3. Cartridge Magazine .......... 4
4. Cartridge magazine (top view) ...... 4
5. Rear panel components ......... 5
6. Ultrium half-height tape drive ...... 8
7. Location coordinates ......... 10
8. Operator Panel components ....... 13
9. Library ready screen ......... 16
10. Password entry screen ......... 16
11. Screen elements ........... 17
12. Confirmation screen.......... 17
13. Java security warning message ...... 18
14. Login page............. 18
15. User account window ......... 19
16. Superuser account window ....... 19
17. Administrator account window ...... 20
18. Rack mount screw locations for front and rear
vertical rails ............ 23
19. Attaching the front brackets to the library
chassis .............. 24
20. Attaching the rear brackets to the rails ... 24
21. Creating the rail assemblies ....... 25
22. Installing the rail assemblies ....... 26
23. Securing the front of the library in the rack 26
24. Securing the rear of the library in the rack 27
25. The cables at the rear of the library .... 27
26. accessor locking screw ......... 28
27. Interface cable connection ........ 28
28. Java security warning message ...... 32
29. Web User Interface login screen ...... 33
30. System summary........... 33
31. Logical library mode settings ...... 34
32. Cartridge assignment settings ...... 35
33. Network settings........... 36
34. Date and time settings ......... 37
35. Application Managed Encryption ..... 38
36. Library Managed Encryption as a choice 39
37. Library Managed Encryption settings .... 39
38. Email notifications .......... 41
39. Trap notifications .......... 42
40. Trap list settings ........... 43
41. SNMPv3 user list settings ........ 43
42. User access settings .......... 44
43. Add User dialog box ......... 45
44. Password Rules screen ......... 46
45. Save configuration .......... 47
46. Cartridge release gate ......... 50
47. Cartridge orientation ......... 51
48. Operator Panel top menus ....... 57
49. Configuration settings ......... 57
50. Current information.......... 57
51. Firmware revision .......... 58
52. Unlock I/O station command ...... 58
53. I/O station unlocked ......... 58
54. Unlock magazine command ....... 59
55. Move cartridge command ........ 59
56. Unload command .......... 60
57. Clean Drive command ......... 60
58. Inventory command ......... 60
59. Online/Offline command ........ 61
60. Move to Ship Position command ..... 61
61. Reboot Drive command ........ 62
62. Reboot Library command ........ 62
63. Logout command .......... 62
64. Auto Cleaning settings ......... 62
65. Active slot count settings ........ 63
66. Library access mode settings ....... 63
67. Date and time settings ......... 64
68. Network settings........... 65
69. Operator Panel settings ........ 66
70. Configuring Web GUI settings ...... 66
71. Factory default settings ........ 67
72. Error status menu .......... 67
73. Run Library Verify command ...... 67
74. Drive diagnostic procedures ....... 68
75. Web User Interface menu ........ 69
76. System Summary screen ........ 70
77. Library Map screen .......... 71
78. Move Cartridges screen ........ 73
79. Unload Drive screen ......... 74
80. Clean Drive screen .......... 74
81. Library State screen .......... 74
82. Inventory screen ........... 75
83. Inventory progress bar ......... 75
84. Unlock magazine .......... 75
85. User Access screen .......... 76
86. Add User dialog box ......... 76
87. Password Rules screen ......... 78
88. Physical library settings screen ...... 79
89. Logical library settings screen ...... 79
90. Network settings screen ........ 81
91. Application Managed Encryption ..... 82
92. Library Managed Encryption as a choice 83
93. Library Managed Encryption settings .... 83
94. Date and time settings screen ...... 84
95. Email settings screen ......... 85
96. SNMP settings screen ......... 86
97. Save/Restore configuration with cookies 88
98. Save/Restore screen.......... 89
99. Operator interventions screen ...... 89
100. View Library Logs screen ........ 90
101. Traces screen ............ 91
102. Download Drive Logs screen....... 92
103. Download Library Logs screen ...... 92
104. Reset library and drive screen ...... 92
105. Firmware Update screen ........ 93
106. Usage Statistics screen ......... 94
107. The LTO Ultrium Data Cartridge ..... 97
108. Ultrium data and WORM tape cartridges 100
109. Sample bar code label on the LTO Ultrium 7
Tape Cartridge ........... 102
ix
Tables
1. Class I Laser Product ......... xiv
2. Data capacity and recording format ..... 2
3. Front panel component descriptions..... 2
4. Rear panel component descriptions ..... 5
5. Ultrium data and cleaning cartridge
compatibility with Ultrium tape drive .... 9
6. Physical specifications ......... 10
7. Electrical specifications......... 10
8. Environmental specifications ....... 10
9. Operational specifications ........ 11
10. Acoustical specifications ........ 11
11. Operator Panel component descriptions 13
12. Location criteria ........... 21
13. Default library configuration settings .... 30
14. Cartridge types and colors ....... 98
15. Cartridge Data Capacity and Recording
Formats .............. 98
16. Nominal cartridge life: Load/unload cycles 99
17. Ultrium data cartridge compatibility with
Ultrium tape drive .......... 99
18. Cartridges and VOLSERs compatible with the
Ultrium Tape Drives ......... 101
19. Location of the write-protect switch .... 103
20. Environment for operating, storing, and
shipping the LTO Ultrium Tape Cartridge .. 106
21. Front Panel LED indicators ....... 117
22. Library error codes ......... 123
23. Drive error codes .......... 133
24. Web user error messages........ 133
25. Trap list ............. 136
26. TapeAlert flags supported by the library 137
27. TapeAlert flags supported by the Ultrium
tape drive............. 139
28. Sense key definitions ......... 143
29. Library sense data .......... 143
30. Ultrium Tape drive sense data ...... 145
31. Ultrium Tape drive sense data - Bytes 12 and
13 ............... 146
xi
xii Dell PowerVault TL1000 Tape Autoloader: User's Guide
Safety and environmental notices
Safety notices and environmental notices for this product are shown and described.
Safety notices
Observe the safety notices when this product is used. These safety notices contain
danger and caution notices. These notices are sometimes accompanied by symbols
that represent the severity of the safety condition.
Most danger or caution notices contain a reference number (Dxxx or Cxxx).
The sections that follow define each type of safety notice and give examples.
Danger notice
A danger notice calls attention to a situation that is potentially lethal or extremely
hazardous to people. A lightning bolt symbol always accompanies a danger notice
to represent a dangerous electrical condition. A sample danger notice follows:
DANGER: An electrical outlet that is not correctly wired could place
hazardous voltage on metal parts of the system or the devices that
attach to the system. It is the responsibility of the customer to ensure
that the outlet is correctly wired and grounded to prevent an electrical
shock. (D004)
Caution notice
A caution notice calls attention to a situation that is potentially hazardous to
people because of some existing condition, or to a potentially dangerous situation
that might develop because of some unsafe practice. A caution notice can be
accompanied by one of several symbols:
If the symbol is... It means...
A hazardous electrical condition with less severity than
electrical danger.
A hazardous condition that is not represented by other
safety symbols.
This product contains a Class II laser. Do not stare into the
beam. (C029) Laser symbols are always accompanied by the
classification of the laser as defined by the U. S.
Department of Health and Human Services (for example,
Class I, Class II).
A hazardous condition due to mechanical movement in or
around the product.
xiii
If the symbol is... It means...
This part or unit is heavy but has a weight smaller than 18
kg (39.7 lb). Use care when lifting, removing, or installing
this part or unit. (C008)
A hazardous condition due to the unit's susceptibility to
electrostatic discharge.
Laser safety and compliance
Table 1. Class I Laser Product
The library might contain a laser assembly that complies with the performance
standards set by the US Food and Drug Administration for a Class I laser
product. Class I laser products do not emit hazardous laser radiation. The
library has the necessary protective housing and scanning safeguards to ensure
that laser radiation is inaccessible during operation or is within Class I limits.
External safety agencies have reviewed the library and have obtained approvals
to the latest standards as they apply.
Performing the safety inspection procedure
Before you service the unit, complete the following safety inspection procedure.
1. Stop all activity between the host and the library’s tape drive.
2. Turn off the power to the library by switching the Power button on the rear of
the tape library to the Off position.
3. Disconnect the tape drive’s SAS cable.
4. Unplug the library’s power cord from the electrical outlet and the library’s
power supply unit.
5. Check the library’s power cords for damage, such as a pinched, cut, or frayed
cord.
6. Check the tape drive’s SAS cable for damage.
7. Check the cover of the library for sharp edges, damage, or alterations that
expose its internal parts.
8. Check the cover of the library for proper fit. It should be in place and secure.
9. Check the product label at the rear of the library to make sure that it matches
the voltage at your outlet.
xiv Dell PowerVault TL1000 Tape Autoloader: User's Guide
Rack safety
The following general safety information must be used for all rack mounted
devices.
DANGER
vAlways lower the leveling pads on the rack cabinet.
vAlways install stabilizer brackets on the rack cabinet.
vTo avoid hazardous conditions because of uneven mechanical loading,
always install the heaviest devices in the bottom of the rack cabinet.
Always install servers and optional devices, starting from the bottom
of the rack cabinet.
vRack mounted devices are not to be used as a shelf or workspace. Do
not place any object on top of rack mounted devices.
vEach rack cabinet might have more than one power cord. Be sure to
disconnect all power cords in the rack cabinet before you service any
device in the rack cabinet.
vConnect all devices that are installed in a rack cabinet to power
devices installed in the same rack cabinet. Do not plug a power cord
from a device that is installed in one rack cabinet into a power device
that is installed in a different rack cabinet.
vAn electrical outlet that is not correctly wired might place hazardous
voltage on the metal parts of the system or the devices that attach to
the system. It is the responsibility of the customer to ensure that the
outlet is correctly wired and grounded to prevent an electrical shock.
CAUTION:
vDo not install a unit in a rack where the internal rack ambient
temperatures might exceed the manufacturer's recommended ambient
temperature for all your rack mounted devices.
vDo not install a unit in a rack where the air flow is compromised.
Ensure that air flow is not blocked or reduced on any side, front, or
back of a unit that is used for air flow through the unit.
vConsideration must be given to the connection of the equipment to
the supply circuit so that overloading of the circuits does not
compromise the supply wiring or overcurrent protection. To provide
the correct power connection to a rack, refer to the rating labels on the
equipment in the rack to determine the total power requirement of the
supply circuit.
v(For sliding drawers) Do not pull out or install any drawer or feature
if the rack stabilizer brackets are not attached to the rack. Do not pull
out more than one drawer at a time. The rack might become unstable
if you pull out more than one drawer at a time.
v(For fixed drawers) This drawer is a fixed drawer and must not be
moved for servicing unless specified by the manufacturer. Attempting
to move the drawer partially or out of the rack might cause the rack
to become unstable or cause the drawer to fall out of the rack.
(R001)
Safety and environmental notices xv
CAUTION:
Removing components from the upper positions in the rack cabinet
improves rack stability during relocation. Follow these general
guidelines whenever you relocate a populated rack cabinet within a
room or building:
vReduce the weight of the rack cabinet by removing equipment,
starting at the top of the rack cabinet. When possible, restore the rack
cabinet to the configuration of the rack cabinet as you received it. If
this configuration is not known, you must do the following:
– Remove all devices in the 32U position and above.
– Ensure that the heaviest devices are installed in the bottom of the
rack cabinet.
– Ensure that there are no empty U-levels between devices that are
installed in the rack cabinet below the 32U level.
vIf the rack cabinet you are relocating is part of a suite of rack cabinets,
detach the rack cabinet from the suite.
vInspect the route that you plan to take to eliminate potential hazards.
vVerify that the route that you choose can support the weight of the
loaded rack cabinet. Refer to the documentation that comes with your
rack cabinet for the weight of a loaded rack cabinet.
vVerify that all door openings are at least 760 x 2032 mm (30 x 80 in.).
vEnsure that all devices, shelves, drawers, doors, and cables are secure.
vEnsure that the four leveling pads are raised to their highest position.
vEnsure that there is no stabilizer bracket that is installed on the rack
cabinet during movement.
vDo not use a ramp that is inclined at more than 10 degrees.
vWhen the rack cabinet is in the new location:
– Lower the four leveling pads.
– Install stabilizer brackets on the rack cabinet.
– If you removed any devices from the rack cabinet, repopulate the
rack cabinet from the lowest position to the highest position.
vIf a long-distance relocation is required, restore the rack cabinet to the
configuration of the rack cabinet as you received it. Pack the rack
cabinet in the original packaging material, or equivalent. Also, lower
the leveling pads to raise the casters off the pallet and bolt the rack
cabinet to the pallet.
(R002)
xvi Dell PowerVault TL1000 Tape Autoloader: User's Guide
Preface
This manual contains information and instructions necessary for the setup,
operation, and servicing of the Dell™PowerVault™TL1000 Tape Library.
xvii
xviii Dell PowerVault TL1000 Tape Autoloader: User's Guide
Chapter 1. Product description
“Front panel” on page 2
“Cartridge magazine” on page 4
“Rear panel” on page 5
“Bar code reader” on page 6
“SAS host interface” on page 6
“Encryption” on page 6
“Supported Internet Protocols” on page 7
“Simple Network Management Protocol (SNMP) messaging” on page 7
“Network Time Protocol” on page 7
“Ultrium tape drives” on page 8
“Media” on page 8
“Logical Unit Number (LUN) scanning” on page 9
“Location coordinates and element addresses” on page 9
“Library specifications” on page 10
“Product environment” on page 11
“Supported device drivers” on page 12
The Dell™PowerVault™TL1000 Tape Autoloader provides compact, high-capacity,
low-cost solutions for simple, unattended data backup. The library has a compact
1U form factor with easy access to tape cartridges with a removable magazine. The
TL1000 Tape Autoloader is an external stand-alone or rack-mountable unit that
incorporates an Ultrium 7 Half-Height Tape Drive (Model S7H), Ultrium 6
Half-Height Tape Drive (Model S6H), Ultrium 5 Half-Height Tape Drive (Model
S5H), or Ultrium 4 Half-Height Tape Drive (Model S4H). It is equipped with a SAS
(Serial Attached SCSI) host adapter attachment that has a data transfer rate of up
to 6.0 Gbps.
The TL1000 Tape Autoloader has a 10-position removable cartridge magazine,
providing a maximum of 9 data cartridge positions, or a maximum of 8 data
cartridge positions with a configurable 1-slot I/O station. One position is reserved
as the tape drive exchange position and can be accessed by the library only. Tape
cartridges that are supported in the TL1000 Tape Autoloader include the 6000 GB
native physical capacity LTO Ultrium Tape Cartridge (Ultrium 7), 2500 GB native
physical capacity LTO Ultrium Tape Cartridge (Ultrium 6), 1500 GB native physical
capacity LTO Ultrium Tape Cartridge (Ultrium 5), 800 GB native physical capacity
LTO Ultrium Tape Cartridge (Ultrium 4), 400 GB Tape Cartridge (Ultrium 3), 200
a29z0176
Figure 1. TL1000 Tape Autoloader
1
GB Tape Cartridge (Ultrium 2), and WORM (Ultrium 7, Ultrium 6, Ultrium 5,
Ultrium 4). The library data storage capacity can be further increased by using
hardware compression.
Table 2. Data capacity and recording format
Type Native Data Capacity Recording Format
Ultrium 7 6000 GB (15000 GB at 2.5:1
compression)
Reads and writes data on
3584 tracks, 32 tracks at a
time.
Ultrium 6 2500 GB (6250 GB at 2.5:1
compression)
Reads and writes data on
2176 tracks, 16 tracks at a
time.
Ultrium 5 1500 GB (3000 GB at 2:1
compression)
Reads and writes data on
1280 tracks, 16 tracks at a
time.
Ultrium 4 800 GB (1600 GB at 2:1
compression)
Reads and writes data on 896
tracks, 16 tracks at a time.
Ultrium 3 400 GB (800 GB at 2:1
compression)
Reads and writes data on 704
tracks, 16 tracks at a time.
Ultrium 2 200 GB (400 GB at 2:1
compression)
Reads and writes data on 512
tracks, 8 tracks at a time.
Ultrium 1 100 GB (200 GB at 2:1
compression)
Reads and writes data on 384
tracks, 8 tracks at a time.
Front panel
2
Table 3. Front panel component descriptions
Number Component Description
▌1▐Operator Panel The Operator Panel features a monochrome
16-character LCD graphic display that is on the
front of the library. Library operations and
service functions are completed from this screen.
The Web User Interface offers some of the same
functionality as the Operator Panel with a web
browser for remote access to the library. For
information about the Operator Panel and the
Web User Interface, see Chapter 2, “User
interfaces,” on page 13.
▌2▐Control keys The control keys are located to the right of the
Operator Panel LCD display on the front of the
library.
PowerVault TL1000
UNLOCK
I/O STATION
a29z0175
12
34
5
5
Figure 2. Front panel components
2Dell PowerVault TL1000 Tape Autoloader: User's Guide
Table 3. Front panel component descriptions (continued)
Number Component Description
▌3▐Cartridge magazine The tape library has a single cartridge magazine
that can hold up to 9 data cartridges, or 8 data
cartridges with a 1-slot I/O station. See Figure 3
on page 4.
Column 5/Tier 1 in the cartridge magazine can
be configured as a 1-slot I/O station. Column
5/Tier 2 in the cartridge magazine is reserved
for the exchange position and can be accessed by
the library only. The I/O station is used to
import and export cartridges without
interrupting normal library operation. Beginning
with Column 4, a minimum of one column can
be reserved for cleaning cartridges. Cleaning
cartridges are used to clean the tape drive heads.
For configuration details, see Chapter 3,
“Installation and configuration,” on page 21.
▌4▐Cartridge magazine
release
Emergency cartridge magazine lock release.
When the I/O station is locked, insert a large,
straightened paper clip twice or hold the paper
clip in place while the cartridge magazine slides
past the I/O station lock.
▌5▐Air vents These vents draw cooler air into the library
enclosure and allow warm air to escape which
helps keep the library at a normal operating
temperature.
Chapter 1. Product description 3
Cartridge magazine
▌1▐Cartridge locations as they appear
in the Library Map.
Note: These labels are for reference
only and do not display on the
magazine.
▌2▐Cartridge magazine
▌3▐Magazine handle
Figure 4 shows the cartridge location label 1 and ruler 2 that appears on the
cartridge magazine. The ruler provides an indication of the distance, when the
magazine is opened or withdrawn, to the end of the magazine before it clears the
front edge of the library. To prevent dropping the magazine, support both ends of
the magazine before it clears the front edge of the library.
a29z0025
Column 5
Tier 2 Column 4
Tier 2 Column 3
Tier 2 Column 2
Tier 2 Column 1
Tier 2
Column 5
Tier 1 Column 4
Tier 1 Column 3
Tier 1 Column 2
Tier 1 Column 1
Tier 1
2
3
1
Figure 3. Cartridge Magazine
a29z0057
21
Figure 4. Cartridge magazine (top view)
4Dell PowerVault TL1000 Tape Autoloader: User's Guide
Rear panel
Table 4. Rear panel component descriptions
Number Component Description
▌1▐Power connector The library connects to a 110/220 volt ac power
supply.
▌2▐Power switch The library is powered ON when the power supply
switch on the rear panel is ON (|). The library has no
independent power switch on the front panel.
▌3▐SAS host interface
connector
Serial-attached SCSI host interface cable connection.
The Ultrium 4, 5, 6, and 7 SAS drives use the
SFF-8088 connection at the drive end and SFF-8088 or
SFF-8470 at the host adapter end.
▌4▐Ethernet port This port is used to connect the library to a network.
▌5▐Accessor locking screw The accessor locking screw is used to lock the
accessor in place during transportation.
Important: Remove the accessor locking screw before
the library is powered ON.
▌6▐Air vent These vents allow air to escape from the power
supply and tape drive sled.
45 1 2 6
3
a29z0003
Figure 5. Rear panel components
Chapter 1. Product description 5
Bar code reader
The bar code reader is a part of the library accessor. The bar code reader reads
each cartridge bar code label that identifies the types of cartridge magazines and
tape drive that is installed in the library. It also provides inventory feedback to the
host application, Operator Panel, and Web User Interface. The library stores the
customized inventory data in memory. Library firmware supports a 6 or
8-character volume serial number (VOLSER) on the bar code label on the tape
cartridge.
SAS host interface
The Ultrium 4, Ultrium 5, Ultrium 6, and Ultrium 7 Half-Height Tape Drives
support the Serial Attached SCSI (SAS) interface. The SFF-8088 SAS connector on
the Ultrium 4, Ultrium 5, Ultrium 6, and Ultrium 7 is compatible with SAS-1 or
SAS-2 cables.
A drive with a SAS (Serial Attached SCSI) interface is linked directly to controllers.
SAS is a performance improvement over traditional SCSI. SAS enables multiple
devices (up to 128) of different sizes and types to connect simultaneously with
thinner and longer cables. Its full-duplex signal transmission supports 6.0 Gb/s
(S4H, S5H, S6H, and S7H). In addition, the TL1000 Tape Autoloader is
hot-plugged, if necessary. SAS drives can auto-negotiate speed.
Encryption
The LTO Ultrium 7, Ultrium 6, Ultrium 5, and Ultrium 4 Tape Drives support host
Application Managed Encryption (AME) with T10 encryption methods, for SAS
drives. Library Managed Encryption (LME) is supported on LTO Ultrium 7 and
Ultrium 6 drives only. Data encryption is supported by LTO Ultrium 7, Ultrium 6,
Ultrium 5, and Ultrium 4 Data Cartridges only.
Important: Contact your Dell technical sales representative about the availability
of Library Managed Encryption (LME).
Note: Application Managed Encryption (AME) does not require a key. Library
Managed Encryption (LME) is available only by purchasing a library with the
Library Managed Encryption enabled at point of sale.
Note: When available, library managed encryption will only be offered for
purchase at point of sale on LTO-6 and LTO-7 TL1000 tape libraries. Library
Managed Encryption will not be offered as an upgrade on existing TL1000 tape
libraries.
The encryption enabled drive contains the necessary hardware and firmware to
encrypt and decrypt host tape application data. Encryption policy and encryption
keys are provided by the host application or host server. A drive digital certificate
is installed at manufacturing time. Each drive receives a unique serial number and
certificate. The T10 application validates each drive instance by checking the
drive’s digital certificate.
The encryption-capable library firmware allows the user to select None or
Application Managed encryption from the Web User Interface. If the library was
purchased with the Library Managed Encryption feature, Library Managed
Encryption can also be selected. The factory default is None.
6Dell PowerVault TL1000 Tape Autoloader: User's Guide
Supported Internet Protocols
The TL1000 Tape Autoloader supports the Internet protocols:
vIPv4
vIPv6
To learn more about IPv4, visit http://www.iana.org/. To learn more about IPv6,
visit http://www.ipv6.org/..
Simple Network Management Protocol (SNMP) messaging
Occasionally, the library might encounter a situation that you want to know about,
such as an open magazine or a fault that causes the library to stop. The library
provides a standard TCP/IP protocol called Simple Network Management Protocol
(SNMP) to send alerts about conditions (such as need for operator intervention)
over a TCP/IP LAN network to an SNMP monitoring station. These alerts are
called SNMP traps. With the information supplied in each SNMP trap, the
monitoring station (together with customer-supplied software) can alert operations
personnel of possible problems or operator interventions that occur.
SNMP traps
SNMP Traps are alerts or status messages that can be collected, monitored, and
used to proactively manage attached libraries with SNMP protocol with the SNMP
monitoring stations. In summary, each trap provides the following information:
vProduct Identification such as product name, description, manufacturer, model
number, firmware level, and the URL that the trap is designated for.
vProduct Status such as the severity of the trap, status (current and previous) and
the time the trap occurred.
vLibrary State (physical device status) such as identification and status of devices
that is monitored. It would include enclosure, power supply, controller,
magazine status, drive count, cartridge slot count, and I/O station count. Also
included would be certain library statistics, and where appropriate, the fault FSC
(fault symptom code) including the severity and description of that fault.
vDrive Status such as the identification of each drive in the library, firmware
level, serial number, and other address and status information.
vTrap Definitions such as library status change, open magazine, I/O accessed,
hard fault information, requests to clean the drive, excessive retries, and
returning to normal operations.
vSNMP MIBs: The library's Management Information Base (MIB) contains units
of information that specifically describe an aspect of the system, such as the
system name, hardware number, or communications configuration. When with
SNMP to monitor your TL1000 Tape Autoloader, make sure that the TL1000 MIB
file is loaded on your SNMP monitoring station. SNMP traps are sent to the
SNMP monitoring stations that are defined for your library (see “Configuring
SNMP trap notifications” on page 86).
Network Time Protocol
NTP is an Internet standard protocol that assures accurate synchronization of
computer clock times in a network of computers. Running as a continuous
background client program on a computer, NTP sends periodic time requests to a
server, obtaining server time stamps, and with them to adjust the client’s clock.
Chapter 1. Product description 7
Ultrium tape drives
The TL1000 Tape Autoloader supports the Ultrium 4 (S4H), Ultrium 5 (S5H),
Ultrium 6 (S6H) , and Ultrium 7 (S7H) half-height tape drives.
The Ultrium 4, Ultrium 5, Ultrium 6, and Ultrium 7 half-height tape drives support
the Serial Attached SCSI (SAS) interface. They have one Mini-SAS (SFF-8088)
connector.
Speed matching
To improve system performance, the Ultrium 4, Ultrium 5, Ultrium 6, and Ultrium
7 Tape Drives use a technique that is called speed matching to dynamically adjust
its native (uncompressed) data rate to the slower data rate of the attached server.
Channel calibration
The channel calibration feature of the Ultrium 4, Ultrium 5, Ultrium 6, and Ultrium
7 Tape Drives customizes each read/write data channel for optimum performance.
The customization enables compensation for variations in the recording channel
transfer function, media characteristics, and read/write head characteristics.
Power management
The Ultrium 4, Ultrium 5, Ultrium 6, and Ultrium 7 Tape Drives feature a power
management function. This function controls the drive’s electronics so that part of
the electronics completely turns OFF when circuit functions are not needed for the
drive’s operation.
Media
The TL1000 Tape Autoloader uses Ultrium tape cartridges that provide up to
6000-GB native capacity (up to 15000 GB with 2.5:1 hardware data compression)
for Ultrium 7 tape drives, 2500-GB native capacity (up to 6250 GB with 2.5:1
hardware data compression) for Ultrium 6 tape drives, 1500-GB native capacity (up
to 3000 GB with 2:1 hardware data compression) for Ultrium 5 tape drives, and
800-GB native capacity (up to 1600 GB with 2:1 hardware data compression) for
Ultrium 4 tape drives.
a80hh015
Figure 6. Ultrium half-height tape drive
8Dell PowerVault TL1000 Tape Autoloader: User's Guide
Table 5. Ultrium data and cleaning cartridge compatibility with Ultrium tape drive
Tape
Drive
LTO Ultrium Data Cartridges
6000 GB
Ultrium 7
2500 GB
Ultrium 6
1500 GB
Ultrium 5
800 GB
Ultrium 4
400 GB
Ultrium 3
200 GB
Ultrium 2
100 GB
Ultrium 1
Ultrium
7
Read/
Write
Read/
Write
Read only
Ultrium
6
Read/
Write
Read/
Write
Read only
Ultrium
5
Read/
Write
Read/
Write
Read only
Ultrium
4
Read/
Write
Read/
Write
Read only
Ultrium
3
Read/
Write
Read/
Write
Read only
Ultrium
2
Read/
Write
Read/
Write
Ultrium
1
Read/
Write
Note: The TL1000 Tape Autoloader supports the Ultrium 4 (S4H), Ultrium 5 (S5H),
Ultrium 6 (S6H), and Ultrium 7 (S7H) Tape Drives only.
For more information about media compatibility, see Chapter 5, “Media,” on page
97.
Logical Unit Number (LUN) scanning
The TL1000 Tape Autoloader uses a single SCSI ID and dual LUNs to control the
tape drive (LUN 0) and library accessor (LUN 1). The library requires a Host Bus
adapter (HBA) that supports LUN scanning. If it is not enabled, your host system
cannot scan beyond LUN 0 and fails to detect the library. It sees only the tape
drive.
Important: Some HBAs, such as RAID controllers, do not support LUN scanning.
Location coordinates and element addresses
The TL1000 Tape Autoloader incorporates patented high-density (HD) slot
technology, which allows multiple cartridges to be stored in a tiered architecture.
The depth of a cartridge location in a high-density slot is known as a tier.
High-density slots are designed to contain multiple cartridges in Tiers 1 and 2.
Note: Each column has a spring-loaded mechanism that pushes a tape cartridge
into Tier 1 when it is the only cartridge in that column. A single cartridge in a
column takes on the Tier 2 element address even though it is physically in Tier 1.
Chapter 1. Product description 9
A storage element address is assigned to each cartridge at the time the cartridge is
inserted. Storage element addresses range from 4097 to 4105 (0x1001 to 0x1009)
when the I/O station is not enabled, and from 4097 to 4104 (0x1001 to 0x1008)
when the I/O station is enabled.
Library specifications
Table 6. Physical specifications
Parameter Measurement
Front panel width (chassis/bezel) 445 mm (17.52 in.)/483 mm (19.02 in.)
Depth 850 mm (33.46 in.)
Height 44 mm (1.73 in.)
Weight (library only) 13 kg (28.66 lbs)
Table 7. Electrical specifications
Parameter Measurement
Voltage 100 - 240 Vac. (4.0 to 1.5 A)
Frequency 50 - 60 Hz
Power consumption 110 W
For more information about installation specifications, see Chapter 3, “Installation
and configuration,” on page 21.
Table 8. Environmental specifications
Parameter Operating (see Note) Storage Shipping
Temperature 10 - 38 °C (50 - 100
°F) 1 - 60 °C (34 - 140 °F) -40 to 60 °C (-40 to
140 °F)
Temperature
variation
10 °C/hour
(maximum)
10 °C/hour
(maximum)
10 °C/hour
(maximum)
Relative humidity 20 - 80% 10 - 90% 10 - 90%
Wet bulb temperature 26 °C (78.8 °F)
maximum
29 °C (84 °F)
maximum
29 °C (84 °F)
maximum
Front Rear
Reservedslot
Column4
Tier2
Column3
Tier2
Column2
Tier2
Column1
Tier2
Column5
Tier1
Column4
Tier1
Column3
Tier1
Column2
Tier1
Column1
Tier1
Drive
Accessor
Column5
Tier2
Figure 7. Location coordinates
10 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Table 8. Environmental specifications (continued)
Parameter Operating (see Note) Storage Shipping
Altitude (meters) 0 - 2,500 0 - 2,500 0 - 2,500
Note: The operating environment of the library must not conflict with the media storage
requirements. The library can operate at elevated temperatures for an extended period.
However, the temperature might shorten the useful life of media that is stored in the
library. If media is stored in the library for more than 10 hours, the storage temperature
requirements for media are met. It is assumed that media stored in the library is
approximately 2 degrees above ambient temperature when the library is powered ON.
Table 9. Operational specifications
Parameter Model S7H Model S6H Model S5H Model S4H
Maximum
storage capacity
54 TB (135 TB
with 2.5:1
compression)
22.5 TB (56.2 TB
with 2.5:1
compression)
13.5 TB (27 TB
with 2:1
compression)
7.2 TB (14.4 TB
with 2:1
compression)
Maximum
number of data
cartridges
9 (including an optional I/O Station)
Drive types Ultrium 7 Half
Height
Ultrium 6 Half
Height
Ultrium 5 Half
Height
Ultrium 4 Half
Height
Sustained native
data transfer rate
300 MB/s (750
MB/s with 2.5:1
compression)
160 MB/s (400
MB/s with 2.5:1
compression)
140 MB/s (280
MB/s with 2:1
compression)
120 MB/s (240
MB/s with 2:1
compression)
Interface 6 Gb/s SAS 3 Gb/s SAS
Note: The Ultrium 4 Half-Height tape drive in S4H libraries that are manufactured after
March 2011 support 6.0 Gb/s and a sustained native data rate of 120 Gb/s.
Table 10. Acoustical specifications
Parameter Measurement
Idling acoustical noise sound power level
LwAD in Bels (1 Bel = 10 dB)
6.6
Maximum acoustical noise sound power
level LwAD in Bels (1 Bel = 10 dB)
6.8
Product environment
The TL1000 Tape Autoloader is designed to operate in a general business
environment.
The library meets the acoustical requirements for general business area category
2D. Category 2D states that the library can be installed a minimum of 4 m (13 ft.)
from a permanent work station.
To allow for service access, install the library a minimum of 0.9 m (3 ft.) from all
obstacles.
The library is a precision computer peripheral device. To ensure maximum
longevity of your library, locate the library away from dust, dirt, and airborne
particulates, as follows:
Chapter 1. Product description 11
vKeep the library away from high-traffic areas, especially if the floor is carpeted.
Carpeting harbors dust and walking on the carpet can cause the carpet fibers
and the dust to become airborne.
vKeep the library out of printer and copier rooms because of toner and paper
dust. Additionally, do not store paper supplies next to the library.
vKeep the library away from moving air caused by doorways, open windows,
fans, and air conditioners.
Ensure that the machine covers are always kept closed to minimize any
contamination from airborne particles.
Supported device drivers
Device drivers enable the drive to interact with various servers. For applications
that use device drivers, see the application’s documentation to determine which
drivers to use.
Note: If you do not have Internet access and you need information about device
drivers, contact your sales representative.
12 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Chapter 2. User interfaces
“Operator Panel”
“Web User Interface” on page 17
The library has a local interface, the Operator Panel, and a remote Web User
Interface (UI).
The Operator Panel is on the front of the library and allows users to work locally
on the library. The Web User Interface allows users and administrators to view and
perform some library functions from remote sites.
The Web User Interface is implemented as a Java™Applet that runs in a web
browser from any PC on the network. The Java Applet requires that Java 1.5.0 or
higher is installed on your host computer for full functionality, and is best viewed
with Internet Explorer 6.0 or higher. Internet Explorer 7.0 or higher is required for
IPv6.
Operator Panel
The Operator Panel is on the front bezel of the library. The Operator Panel displays
library information and menu commands that are used to run library management
functions in response to the control keys on the right of the LCD display.
Table 11. Operator Panel component descriptions
Number Component Description
▌1▐LCD display 16-character LCD graphic display
▌2▐Up key (∆) Button that is used to navigate upward (↑) through the menu
items
▌3▐Down key (∇) Button that is used to navigate downward (↓) through the
menu items
a29z0177
24
6789
135
Figure 8. Operator Panel components
13
Table 11. Operator Panel component descriptions (continued)
Number Component Description
▌4▐Cancel key Button that is used to cancel a user action and return to the
last menu item
▌5▐Enter key Button that is used to display a submenu or to select a user
action
▌6▐Ready/Activity
LED
Green LED lit when the unit is powered ON. The LED
flashes when there is any library activity or the library is
offline.
▌7▐Clean Drive
LED
Amber LED lit when the drive needs cleaning. The LED
turns OFF after the drive is cleaned successfully.
▌8▐Attention LED Amber LED lit when a cartridge is incompatible with the
drive, marginal, or invalid. The LED turns OFF when the
media is removed from the drive. The LED might also be lit
when there is a power supply problem.
▌9▐Error LED Amber LED lit when there is an unrecoverable library or
drive failure. The corresponding error message displays on
the LCD display.
The Operator Panel operates in two basic modes:
vUser Interaction mode - Mode that is employed when a user is pushing keys on
the Operator Panel.
vSystem Driven mode - Normal mode of operation where the Operator Panel
displays status in response to commands issued from the drive's internal
interface.
When an Operator Panel key is pressed and released, the Operator Panel
automatically changes to User Interaction mode. User Interaction mode continues
until 3 minutes after a user stops pushing keys, or the requested accessor action
stops, whichever is longer. Then, the Operator Panel returns to System Driven
mode.
If necessary, the Operator Panel automatically changes to System Driven mode.
When this change occurs, the library remembers what the user was doing before
the display mode changed.
Any operational conflict between commands that are received over the host
interface or the Web User Interface and those commands that are entered by way
of the Operator Panel are avoided with a reservation mechanism on a first-come,
first-served basis. Operator Panel commands are canceled by an Operator Panel
logout or timeout.
Library firmware does not allow a user to select an impossible request. Those
situations include, but are not limited to -
vMoving a cartridge from any source to a position occupied by another cartridge
vMoving a cartridge from an empty cartridge position
vLoading a cartridge from any source to a full drive
vUnloading a cartridge from an empty drive
Any error that is detected by the library or drive controller and not recoverable
through predetermined firmware algorithms is considered unrecoverable. When an
error occurs, an error code is displayed on the Operator Panel display and the
14 Dell PowerVault TL1000 Tape Autoloader: User's Guide
error LED is ON. The error code remains on the Operator Panel until a key is
pressed, which causes the Operator Panel to return to the Home Screen. Numeric
error codes are used for unrecoverable errors. Otherwise, text status messages are
displayed.
When the library powers ON or resets, it goes through several internally controlled
initialization processes, called the Power-On-Self-Test (POST).
Front panel LEDs
All LEDs are updated during power ON and reset sequences. At power ON or
software reset, all LEDs turn ON as soon as POST allows. When initialization
starts, all LEDs turn OFF and the Ready/Activity LED flashes at a rate of
approximately 2 seconds per cycle. When the mechanical initialization is complete,
the Ready/Activity LED stops flashing and turns ON.
If a library failure occurs, the Ready/Activity LED turns OFF and the Error LED
turns ON. The Operator Panel also displays an appropriate error code to help
identify the failure.
The following are more operational details of LEDs:
vThe Ready/Activity LED (▌6▐in Figure 8 on page 13) turns ON any time the
unit is powered ON and functional. The Ready/Activity LED flashes whenever
there is library. This LED also flashes when the library is offline.
vThe Clean Drive LED (▌7▐in Figure 8 on page 13) turns ON when a “cleaning
required” command is issued by the drive. The LED turns OFF after a successful
drive cleaning operation.
vThe Attention LED (▌8▐in Figure 8 on page 13) turns ON to indicate that a
piece of media is bad/marginal, or invalid. The LED turns OFF when all
marginal and invalid cartridges are exported from the library. The Attention LED
also turns ON if Autoclean is enabled and no cleaning cartridge is in a cleaning
position.
vThe Error LED (▌9▐in Figure 8 on page 13) turns ON when there is an
unrecoverable drive or library failure. An error message is displayed on the
screen and the LED remains ON until the error state is resolved.
For information, see “Interpreting front panel LEDs” on page 116.
Input modes
There are several ways to enter values in the different menu items. These values
are selectable predefined values, toggle values (for example, ON/OFF) and
numerical values like network addresses.
Selecting predefined values
1. To set the predefined values, press the Enter key to select the menu item.
2. With the Plus and Minus keys, select one of the various predefined values for
that item.
3. As soon as the Operator Panel display shows the correct value, press the Enter
key to apply the value.
Toggling values
Toggle values are used to switch between two different states like ON and OFF.
Chapter 2. User interfaces 15
1. After you navigate to the menu item, press the Enter key to select the menu
item.
2. With the Plus and Minus keys, select one of the various predefined states for
that item.
3. Press the Enter key to apply the new state.
Entering numerical values
Numerical values are needed for network addresses, password entries, and other
configuration entries.
1. After you navigate to the menu item, the current value is displayed and the
cursor highlights the first digit of the value that can be changed.
2. For each digit to be changed in the value:
a. Use the Plus and Minus keys to increment or decrement the digit.
b. Press the Enter key to highlight the next editable digit.
3. Press the Enter key at the last digit to apply the complete entry. Press the
Cancel key to cancel the whole edit process and maintain the original value.
Logging in
At power ON or software reset, the library ready screen displays when POST
initialization completes successfully.
To log in to the Operator Panel, press the Enter key. The password entry screen
displays.
Press the UP and DOWN arrow keys to change the current digit. Press the Enter
key to advance to the next digit. The default password is 0000. When you are
logged in, you can change the password with the Change Login Password
command. See “Configuring Operator Panel settings” on page 66.
a29z0028
Figure 9. Library ready screen
a29z0029
Figure 10. Password entry screen
16 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Screen elements
The Operator Panel displays a single menu item (▌1▐in Figure 11) on each screen.
The existence of other menu items above and below the currently displayed item is
indicated by the arrows (▌2▐in Figure 11) on the right side of the screen.
In the Configuration menu, the current configuration setting is indicated by an
asterisk (▌3▐in Figure 11) on the right side of the screen. For example, in Figure 11,
the I/O station is enabled. When a configuration setting is changed, the
confirmation screen in Figure 12 displays. Press the Enter key to confirm, or Cancel
to return to the previous screen.
Web User Interface
The Web User Interface Java Applet requires Java 1.5.0 or higher be installed on
your host computer for full function, and is best viewed with Internet Explorer 6.0
or higher. Internet Explorer 7.0 or higher is required for IPv6. If your computer
does not have Java installed or you must upgrade your installation, download the
latest version of the Java Runtime Environment (JRE) for your platform from
http://www.java.com/. Follow the instructions that are provided to enable and
configure the Java Runtime Environment for your browser.
The Web User Interface can also be used to update the library and drive firmware,
and to download error logs, drive memory dumps, and other library data.
Before the TL1000 Tape Autoloader can be managed over a network with the Web
User Interface, set up the initial network configuration of the library with the
Operator Panel. For information, see “Configuring network settings” on page 47.
Logging in
To log in to the Web User Interface from Internet Explorer, you must enter the IP
address of the library. The IP address can be obtained with the View Settings
command from the Operator Panel. For example, http://192.168.1.1.
When the applet starts, the following warning message displays. This message is
normal and does not indicate a problem.
2
1
a29z0030
3
Figure 11. Screen elements
a29z0032
Figure 12. Confirmation screen
Chapter 2. User interfaces 17
After the Web User Interface is started, the login window is displayed.
The factory default account login and password for an Administrator account is
vAccount: admin
vPassword: secure
The account name and password are case-sensitive. After your account name and
password are entered, use your mouse to click Login or press the Enter key.
For information about account privileges, see “User privileges” on page 20.
Common header elements
All Web User Interface windows (except for the Login screen) contain the
following common elements in the header
vHelp - Click to read context-sensitive help for the associated page.
a29z0194
Figure 13. Java security warning message
a29z0195
Figure 14. Login page
18 Dell PowerVault TL1000 Tape Autoloader: User's Guide
vLogoff - Click to log out of the Web User Interface.
Menus available from the Web User Interface
Figure 15 shows the Web User Interface window for a User account, Figure 16
shows the window for a Superuser account, and Figure 17 on page 20 shows the
window for an Administrator account.
a29z0196
Figure 15. User account window
a29z0197
Figure 16. Superuser account window
Chapter 2. User interfaces 19
For a complete description of all Web User Interface menu options, see Chapter 4,
“Operations,” on page 55.
User privileges
User privilege levels are manually assigned to user accounts created within the
library. Controlling access to screens and operations within the library preserves
the integrity of the library and the data that is stored within the library.
There are three types of user privileges in the library.
vUsers are allowed to monitor the library, but not complete actions that affect the
physical library.
vSuperusers are allowed to operate the physical and logical library, but not
complete actions that affect the library configuration.
vAdministrator users are allowed access to the entire physical library and logical
library, including configuration. Only one administrator user must be assigned
the login name admin.
User privileges include
vMultiple users can be logged in at one time on the Web User Interface.
vAny user can be logged in to only one interface at a time.
a29z0198
Figure 17. Administrator account window
20 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Chapter 3. Installation and configuration
“Choosing a location”
“Installing in a rack” on page 22
“Removing the accessor locking screw” on page 27
“Attaching the library to a server” on page 28
“Configuring your library with the
Web User Interface” on page 31
“Logging in to the Web User Interface” on page 32
“Checking firmware level” on page 33
“Configuring library settings” on page 34
“Configuring network settings” on page 36
“Configuring date and time settings” on page 37
“Configuring encryption settings” on page 38
“Configuring email notifications” on page 41
“Configuring trap notifications” on page 42
“Managing user access” on page 44
“Saving the library configuration” on page 47
“Configuring your library with the
Operator Panel” on page 47
“Logging in to the Operator Panel” on page 47
“Configuring network settings” on page 47
“Configuring library settings” on page 49
“Populating the library with cartridges” on page 50
“Verifying library and drive operation” on page 51
“Taking the Library Online” on page 52
“Registering for support notification” on page 52
To install and configure a TL1000 Tape Autoloader, complete these procedures in
the order they are presented.
Choosing a location
Table 12. Location criteria
Criteria Definition
Room temperature 16 - 32 °C (60 - 90 °F)
Voltage 100 - 240 Vac. (4.0 to 1.5 A)
Note: The power switch is on the rear of the
library and must be easily accessible.
Frequency 50 - 60 Hz
Relative humidity 20 - 80% non-condensing
Air quality The library must be placed in an area with
minimal sources of particulate
contamination. Avoid areas near frequently
used doors and walkways, stacks of supplies
that collect dust, printers, and smoke-filled
rooms. Excessive dust and debris can
damage cartridges and the tape drive.
21
Table 12. Location criteria (continued)
Criteria Definition
Clearance vBack: Minimum of 15 cm (6 in.)
vFront: Minimum of 30 cm (12 in.)
vSides: Minimum of 5 cm (2 in.)
Rack requirements Standard EIA 19-inch rack: 1U space
Installing in a rack
The TL1000 Tape Autoloader can be easily installed into a standard 19-inch rack
system. A standard 19-inch rack system contains multiple mounting locations that
are called EIA units as defined by the Electronics Industries Association. Each EIA
unit contains three square or round holes that are used to mount rack designed
equipment. The library requires 1 EIA unit (1U) of rack space. Each unit is
separated by a small space.
When you decide on a location in your rack for the library, consider that the
Operator Panel has a small LCD screen. The library must be positioned to allow
for easy viewing. The rear of the library must be free from any obstructions to
allow easy access to the power switch and other rear panel components.
Note: Before you begin the rack installation of the library, read the safety
information in “Rack safety” on page xv. Also, verify that no desktop feet are
attached to the bottom of the library.
To install the library in a rack:
1. Verify that your rack kit includes all the necessary contents.
2. Determine the location in your rack for your library to be installed. With a
pencil, mark the location on the front vertical rails and rear vertical rails
(Figure 18 on page 23) in your rack.
22 Dell PowerVault TL1000 Tape Autoloader: User's Guide
3. Place the screws ▌11▐into the left and right brackets.
4. Attach the left ▌3▐and right ▌4▐(Figure 19 on page 24) front brackets to the
front of the library chassis with 2 flat-head screws ▌8▐on each side. Use the
top two screw holes on each side. The flange of each bracket with the inserted
screws (▌11▐) fits into the cutout on each side of the bezel.
a29z0015
Figure 18. Rack mount screw locations for front and rear vertical rails
Chapter 3. Installation and configuration 23
5. Attach the left ▌1▐and right ▌2▐rear brackets to the left ▌5▐and right ▌6▐
front rails with 2 round-head screws ▌10▐on each side (Figure 20).
Important: Do NOT tighten these screws completely.
6. Slide in the rear rails ▌7▐from back to front, to create the rail assemblies.
Ensure that the screw holes face outwards (Figure 21 on page 25).
a29z0185
3
8
4
8
11
Figure 19. Attaching the front brackets to the library chassis
a29z0019
56
10
12
12
Figure 20. Attaching the rear brackets to the rails
24 Dell PowerVault TL1000 Tape Autoloader: User's Guide
7. Install the rail assemblies into the rack (Figure 22 on page 26). Ensure the 3
holes in the front of the unit align with the 1U space marked on the vertical
rails in Step 2. Secure the rails to the rack with 4 flat-head screws ▌9▐on each
side of the rack. Use the top and bottom screw locations on the front and rear
of the rack rail (Figure 18 on page 23)).
a29z0018
7
Figure 21. Creating the rail assemblies
Chapter 3. Installation and configuration 25
8. Slide the library chassis into the rack. The heads of the large screws ▌11▐
appear through the oval openings on each side of the bezel. Use a Phillips
screwdriver to attach these screws to the rack (Figure 23).
a29z0020
9
9
Figure 22. Installing the rail assemblies
a29z0186
Figure 23. Securing the front of the library in the rack
26 Dell PowerVault TL1000 Tape Autoloader: User's Guide
9. Secure the rear of the library to the rack with a round-head screw ▌10▐on
each rear bracket (Figure 24). Tighten the other rear bracket screws to secure
the library to the rack.
10. Run the SAS cable, power cable, and Ethernet cable through the
hook-and-loop fastener strap ▌12▐. Leave enough slack to reach the
corresponding connectors, then tighten the strap (Figure 25).
Note: For information about converting and relocating the library, see
Chapter 8, “Removal and replacement procedures,” on page 121.
Removing the accessor locking screw
Important: The accessor locking screw prevents the library accessor from moving
during shipment and must be removed before the library is powered ON.
Remove the accessor locking screw, located on the rear panel of the library (▌1▐in
Figure 26 on page 28).
a29z0022
1010
Figure 24. Securing the rear of the library in the rack
a29z0023
12
Figure 25. The cables at the rear of the library
Chapter 3. Installation and configuration 27
Attaching the library to a server
The drive is attached to a server with the Serial Attached SCSI (SAS) interface. The
Web User Interface accesses the library with an ethernet interface.
Connecting the Host Interface cables
To connect the host interface cable to the library:
Note: It is recommended that you shut down and turn OFF the associated server
before you connect the SAS interface cable. Turn ON the associated server after the
SAS interface cable is connected to the library and server, the library is powered
ON, and the library completed the initialization.
1. Attach an ethernet cable to the ethernet port (▌1▐in Figure 27)
Note: On rack mount installations, run the cable through the hook-and-loop
fastener strap on the right rear bracket.
a29z0102
1
Figure 26. accessor locking screw
a29z0100
1 2 3
Figure 27. Interface cable connection
28 Dell PowerVault TL1000 Tape Autoloader: User's Guide
2. Attach the host end of the SAS cable to the drive’s SAS connector (▌2▐in
Figure 27 on page 28). See “SAS host interface” on page 6 for information about
the type of SAS connector that is required for attachment to the drive.
Note: On rack mount installations, run the cable through the hook-and-loop
fastener strap on the right rear bracket.
3. Attach the other end of the host SAS interface cable to the host or to an
interposer if required.
4.
vMethod 1: Plug the ethernet cable into your server or PC to access the Web
User Interface directly. This method modifies your server or PC network
settings to match the library default settings. You can also use the library
Operator Panel to change the library network settings to match the server or
PC network settings before you use the Web User Interface to access the
library. If the ethernet connection is directly attached to a server or a PC, a
crossover ethernet cable might be required.
vMethod 2: Plug the ethernet cable into an ethernet switch or router to access
the Web User Interface on a LAN (local area network). The library network
settings must be entered with the Operator Panel before the Web User
Interface is used to access the library.
Connecting the power cord
Important: This product can ONLY be used with an approved power cord for your
specific geographic region. Use of an unapproved power cord might result in
vNot meeting individual country-specific safety requirements
vOverheating with potential personal injury or property damage
vA fracture that results in internal contacts that are exposed, which might subject
the user to a shock hazard
To connect a power cord:
1. Plug one end of the power cord or rack PDU power cord into the power
connector (▌3▐in Figure 27 on page 28) on the rear panel of the library.
Note: On rack mount installations, run the rack PDU power cord through the
hook-and-loop fastener strap on the right rear bracket, and tighten the strap.
The rack PDU power cord is a special power cord that plugs into a rack power
strip.
2. Plug the other end of the power cord into the nearest properly grounded
power outlet. On rack mount installations, plug the other end of the rack PDU
power cord into the nearest rack PDU.
3. Power ON the library by toggling the power switch on the power supply to the
ON (|) position.
4. Wait for the library to initialize.
During initialization, the library completes a Power ON Self Test (POST) to
ensure that the library hardware is functional. The library also tests
communications with the tape drive over the internal bus.
Note: If the Operator Panel does not initialize, check all cable connections, and
ensure that the cartridge magazine is closed and in the locked position. Ensure that
the power supply switch is in the ON position. If the Operator Panel still does not
initialize, see Chapter 6, “Troubleshooting,” on page 109.
Chapter 3. Installation and configuration 29
Important: To disconnect all power from the library, turn the power switch to the
OFF position, then remove the power cord from the outlet. The power switch
removes power from portions of the library and the drive, but the power supply
still has ac power at its input.
Note: When the library is power-cycled, wait 10 seconds after the power is OFF
before the library is powered ON again.
Configuring the library
The library can be configured with the Web User Interface or the Operator Panel.
The preferred method for configuring your library is by using the Web User
Interface. See “Configuring your library with the Operator Panel” on page 47 and
“Configuring your library with the Web User Interface” on page 31.
For complete detailed information about all of the functions available on the
library with the Operator Panel and the Web User Interface, see Chapter 4,
“Operations,” on page 55.
The default library configuration settings are listed in Table 13.
Table 13. Default library configuration settings
Configuration Item Default Setting
NETWORK
Ethernet link speed Auto
SSL security Disabled
IPv4 settings Enabled
DHCP (Dynamic Host Configuration
Protocol)
Enabled
Static IP address Disabled
IPv4 address 0.0.0.0
Subnet mask 255.255.255.0
Gateway 0.0.0.0
IPv6 settings Disabled
DHCP (Dynamic Host Configuration
Protocol)
Enabled
Stateless auto-configuration Enabled
Static IP address Disabled
IPv6 address 0:0:0:0:0:0:0:0
Prefix length 64
Gateway 0:0:0:0:0:0:0:0
DNS setting Disabled
DNS IP address 0.0.0.0
PHYSICAL
Library name (Blank)
Auto Cleaning Disabled
Bar code label length 8 characters
LOGICAL
30 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Table 13. Default library configuration settings (continued)
Configuration Item Default Setting
Library mode Random
Loop Enabled
Auto Load Enabled
Active slots 9 + 0
ENCRYPTION
Encryption method None
DATE and TIME
NTP server Disabled
NTP server address 0.0.0.0
Time zone (GMT) +00:00
Date (MM/DD/YYYY) 01/08/2008
Auto adjustment by PC Every 1 minute
NOTIFICATIONS
SMTP (mail) settings
Mail server address 0.0.0.0
Mail event Error events enabled
SNMP (trap) settings
Community Public
Trap event Error events enabled
SNMPv3 engine ID (Set by library firmware)
Static library network settings must be entered with the Operator Panel before the
library can be accessed remotely with the Web User Interface. If your system is
serviced by a Dynamic Host Configuration Protocol (DHCP) server, the network
parameters are automatically set. Once remote access is established, you can
complete the configuration of your library remotely.
If you choose to use the Operator Panel to configure your library, go to
“Configuring your library with the Operator Panel” on page 47.
Configuring your library with the Web User Interface
If you choose to use the Web User Interface to configure your library, first enter
your library network settings with the Operator Panel (see “Configuring network
settings” on page 65).
To configure your library with the Web User Interface:
1. Install Java 1.5.0 or higher on your host computer. Download the latest
version of the Java Runtime Environment (JRE) for your platform from
http://www.java.com/.
2. “Logging in to the Web User Interface” on page 32
3. “Checking firmware level” on page 33
4. “Configuring library settings” on page 34
5. “Configuring network settings” on page 36
6. “Configuring date and time settings” on page 37
Chapter 3. Installation and configuration 31
7. “Configuring encryption settings” on page 38
8. “Configuring email notifications” on page 41
9. “Configuring trap notifications” on page 42
10. “Managing user access” on page 44
11. “Saving the library configuration” on page 47
Logging in to the Web User Interface
To log in to the Web User Interface:
1. If necessary, obtain the IP address of the library on the Operator Panel.
a. From the top menu of the Operator Panel, press the Minus key to select
View Current Information, and press Enter.
b. Press the Minus key until the IP Address setting is displayed and make a
note of the IP address.
c. Press the Cancel key repeatedly to log out of the Operator Panel.
2. Open Internet Explorer on your server or PC to access the Web User Interface.
3. In the browser address field, enter your library's IP address URL to start the
Web User Interface applet in the browser window. For example,
http://192.168.1.1
When the applet launches, the warning message in Figure 28 displays. This
message is normal and does not indicate a problem.
4. Click Run.
5. On the Web User Interface login screen, enter the administrator login account
name and default password.
vAccount: admin
vPassword: secure
a29z0194
Figure 28. Java security warning message
32 Dell PowerVault TL1000 Tape Autoloader: User's Guide
6. Click Login.
Checking firmware level
Check the current level of library firmware that is displayed in the System
Summary. If an updated level of firmware is available, download and update the
library firmware before normal operation starts. See “Updating library and drive
firmware” on page 93.
a29z0099
Figure 29. Web User Interface login screen
a29z0193
Figure 30. System summary
Chapter 3. Installation and configuration 33
Configuring library settings
Logical library settings
To configure the library access mode settings for the logical library:
1. Expand Configure Library, if necessary, and click Logical in the left navigation
pane of the Web User Interface.
2. Select the Library Mode.
vRandom - In random mode, the library allows the server's (host's)
application software to select any data cartridge in any order.
vSequential - In sequential mode, the library's firmware predefines the
selection of the cartridges. After initialization, the firmware causes the library
to select the first available cartridge found (counting from the lowest
Column/Tier position through the highest cartridge position in your library)
for loading into the drive. See “Location coordinates and element addresses”
on page 9.
–Loop - Sequential mode with loop mode ON loads the cartridge in the
lowest Column/Tier cartridge position after the cartridge in the highest
Column/Tier cartridge position is filled with data and sent back to its
home position. This mode allows endless backup operations without user
interaction.
–Autoload - Sequential mode with autoload mode ON loads the first
available cartridge (the lowest Column/Tier cartridge position that
contains a cartridge) automatically if the library powers ON, or resets,
with an empty drive. If the library powers ON with a cartridge already in
the drive, sequential mode starts from the home position of that cartridge,
unless the host issues a rewind and unload command to the drive. In
which case the next cartridge in sequence will be loaded into the drive.
To start sequential mode if autoload is OFF, use the Move Cartridge
command to load the first cartridge into the drive. The sequence starts from
the home position of that cartridge. Cartridges need not to be in contiguous
slots.
To stop sequential mode, use the Move Cartridge command to unload the
drive. This command cancels sequential mode; the next sequential cartridge
is NOT loaded.
To restart sequential mode, use the Move Cartridge command again to load a
cartridge; the loading sequence resumes from the home position of that
cartridge.
vNumber of active slots - Select the number of active slots you would like to
assign in your library. Selecting the number of active slots defines the
number of storage slots, number of cleaning/inactive slots, whether the I/O
Station is enabled/disabled, and whether auto cleaning is allowed. The first
digit configures the number of active storage positions (4, 6, 8, or 9). The
a29z0124
Figure 31. Logical library mode settings
34 Dell PowerVault TL1000 Tape Autoloader: User's Guide
second digit configures Column 5, Tier 1 of the magazine as an I/O Station
(0 when disabled, and 1 when enabled). The Auto Cleaning function can be
enabled only if there is at least one inactive position in the magazine. If Auto
Cleaning is enabled, the inactive positions become cleaning cartridge
positions.
3. Click Submit to enable the settings.
Physical library settings
To configure the library cartridge assignment settings, complete the following
procedure:
1. Expand Configure Library, if necessary, and click Physical in the left
navigation pane of the Web User Interface.
2. Select the Library settings.
vLibrary name - Enter a name for your library.
vAuto Cleaning - Automatically cleans the drive when the drive requests that
cleaning and a cleaning cartridge is present in the library. Auto cleaning can
be enabled only when there is at least one inactive position in the magazine
in the library.
Note: It is recommended that the Auto Clean function is enabled on the
library. With the Auto Clean function enabled, drive cleaning occurs
automatically. The only time Auto Cleaning must be disabled is when your
Backup Application requires that it has control.
vBar code label length - Use to choose the number of characters in the
cartridge bar code that is reported to the host computer.
3. Click Submit to enable the settings.
a29z0123
Figure 32. Cartridge assignment settings
Chapter 3. Installation and configuration 35
Configuring network settings
Once the network settings are entered on the Operator Panel, the current network
configuration of the library can be modified with the Web User Interface. The
changes that are made to the network settings do not take effect until after the
library is rebooted.
To modify the network settings:
1. Expand Configure Library, if necessary, and click Network in the left
navigation pane of the Web User Interface.
2. Select the Ethernet Link speed (duplex mode).
3. Select the TCP/IP settings. To enable dual IPv4/IPv6 protocol, select both Use
IPv4 and Use IPv6 and enter parameters for both.
vSecurity - Select Enable SSL for Web to provide secure communications
between the web browser and the tape library.
vIPv4 setting - Select Use IPv4 to enable the IPv4 Internet Protocol. Select the
corresponding button to obtain an IP address automatically (DHCP) or use
static IP address settings. When with DHCP, use the Operator Panel to
determine the library's assigned IP address. See “Configuring network
settings” on page 65. Enter the following parameters if with static IP address
settings.
–IPv4 address - Sets the TCP/IPv4 address of the library on the network.
–Subnet mask - Defines and limits users within a local network.
–Gateway - Allows access outside the local network.
vIPv6 setting - Select Use IPv6 to enable the IPv6 Internet Protocol. Select the
corresponding button to obtain an IP address automatically (DHCP), to
obtain an IP address with stateless auto configuration, or use static IP
address settings. Enter the following parameter if with static IP address
settings.
–IPv6 address - Sets the TCP/IPv6 address of the library on the network.
a29z0125
Figure 33. Network settings
36 Dell PowerVault TL1000 Tape Autoloader: User's Guide
–Prefix length - Decimal value that indicates the number of contiguous,
high-order bits comprising the network portion of the address.
–Gateway - Allows access outside the local network.
vDNS setting - Select Use DNS to use a domain name server. The DNS
server, if entered, allows the encryption, date and time, and notifications IP
addresses to be specified with host names instead of numerical IP addresses.
–DNS IP address - Sets the IP address of the DNS server.
4. Click Submit to enable the settings.
Configuring date and time settings
Configure the date and time settings with one of three methods: automatically with
a remote NTP time server on the network, automatically with the clock on your
host computer, or manually.
Note: Selecting Refresh refreshes the date and time.
Note: If you choose to manually set your date and time, you must reset the date
and time after the library is power-cycled and after a library reset.
Note: When the library is power-cycled, wait 10 seconds after the power is OFF
before the library is powered ON again.
Once the network settings are entered on the Operator Panel, the current date and
time can be modified with the Web User Interface.
The TL1000 Tape Autoloader communicates with an NTP server with the following
conditions:
vClient/server basis operation
vUDP (User Datagram Protocol) to access the NTP server
vDoes not use authentication keys
vLibrary polling is every 12 hours
To modify the date and time settings:
1. Expand Configure Library, if necessary, and click Date and Time in the left
navigation pane of the Web User Interface.
2. Select the Date and Time settings.
vNTP Server - Enables time and date control with a time server on the
network.
a29z0170
Figure 34. Date and time settings
Chapter 3. Installation and configuration 37
–NTP server address - Enter the IP address of the time server. IPv4 and
IPv6 addresses are supported, depending on the TCP/IP settings. Host
names can be entered instead of numerical IP addresses if Use DNS is
selected in the Network settings.
–Time zone - Enter the time zone relative to Greenwich Mean Time (GMT).
vIf the time server is disabled, enter the local time and date manually.
–Date - Enter the date with the MM/DD/YYYY format.
–Time - Enter the time with the HH:MM:SS format.
vAuto Adjustment by PC - Select a time interval and click Start to
synchronize the library with the clock on your host computer at regular
intervals. The Web User Interface Java Applet must be running continuously
to use this function.
3. Click Submit to update the settings.
Configuring encryption settings
Two types of encryption can be configured for your library. The default is None.
The two types are
vApplication Managed Encryption - For encryption in operating environments
that run an application capable of generating and managing encryption policies
and keys.
vLibrary Managed Encryption - For encryption by the TL1000 Tape Autoloader
tape drive.
If you did not purchase the feature for Library Managed encryption, you can
configure your library for Application Managed encryption. If you select
application-managed encryption, no further configuration steps are necessary. Click
Submit to enable the setting.
Important: Contact your Dell technical sales representative about the availability
of Library Managed Encryption (LME).
Note: Library Managed Encryption (LME) is available only by purchasing a library
with the Library Managed Encryption Feature installed. When available, library
a29z0210
Figure 35. Application Managed Encryption
38 Dell PowerVault TL1000 Tape Autoloader: User's Guide
managed encryption will only be offered for purchase at point of sale on LTO-6
and LTO-7 TL1000 tape libraries. Library managed encryption will not be offered
as an upgrade on existing TL1000 tape libraries.
To modify the encryption settings:
1. Expand Configure Library, if necessary, and click Encryption in the left
navigation pane of the Web User Interface.
2. In the Encryption method: drop-down menu, choose Library Managed
Encryption (if the library is purchased with the Library Managed Encryption
feature) to enable encryption in your library. Application Managed Encryption
is also a choice. No further configuration steps are necessary for Application
Managed Encryption.
3. Select the Encryption policy settings (library-managed encryption only).
a29z0199
Figure 36. Library Managed Encryption as a choice
a29z0212
Figure 37. Library Managed Encryption settings
Chapter 3. Installation and configuration 39
vEncrypt All - All tape cartridges that are loaded into the tape drive are
encrypted.
vInternal Label - Selective Encryption - This option is used only for
Symantec's Veritas NetBackup.
vInternal Label - Encrypt All - This option is used only for Symantec's Veritas
NetBackup.
4. Select the Security settings (library-managed encryption only).
vEnable SSL for EKM - Select to enable secure communications between the
tape library and the EKM server.
5. Select the Primary EKM Server Settings (library-managed encryption only) -
The address of the primary encryption key manager on a server. IPv4 and IPv6
addresses are supported. Host names can be entered instead of numerical IP
addresses if the DNS server is specified.
vAddress - The IP address of the primary encryption key manager.
vTCP port number - The port number of the primary encryption key manager
for TCP. The default port number is 3801.
vSSL port number - The port number of the primary encryption key manager
for SSL. The default port number is 443.
6. Select the Secondary EKM Server Settings (library-managed encryption only) -
The address of the secondary encryption key manager on a server. IPv4 and
IPv6 addresses are supported. Host names can be entered instead of numerical
IP addresses if the DNS server is specified.
vAddress - The IP address of the secondary encryption key manager.
vTCP port number - The port number of the secondary encryption key
manager for TCP. The default port number is 3801.
vSSL port number - The port number of the secondary encryption key
manager for SSL. The default port number is 443.
7. Click Submit to enable the settings.
40 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Configuring email notifications
Note: This procedure is optional.
To set up email notifications of library events:
1. Expand Configure Library, if necessary, and click Notifications in the left
navigation pane of the Web User Interface.
2. Click the SMTP (Mail) Settings tab.
3. Configure the SMTP server and header settings.
vSMTP server address - SMTP mail server address. IPv4 and IPv6 addresses
are supported. Host names can be entered instead of numerical IP addresses
if the DNS server is specified in the Network settings.
vSender address - Mail header information.
vSubject - Mail header information.
4. Enter the email addresses to be notified when an event takes place in the Mail
To fields.
5. Select the event level to report in the Mail Event field.
6. Click Test to send a test email message to the enabled addresses.
7. Click Submit to enable the settings.
a29z0127
Figure 38. Email notifications
Chapter 3. Installation and configuration 41
Configuring trap notifications
Note: This procedure is optional. SNMP notifications are not enabled unless there
is a check mark in the SNMP Enabled check box. To disable SNMP notifications,
clear the SNMP Enable check box and click Submit.
The traps that are supported by the TL1000 Tape Autoloader are listed in “Trap
definitions (types)” on page 136.
To set up trap notifications for an SNMP server:
1. Expand Configure Library, if necessary, and click Notifications in the left
navigation pane of the Web User Interface.
2. Click the SNMP Settings tab.
3. Click to place a check mark in the SNMP Enabled check box.
4. Configure the SNMP server and header settings.
vCommunity - SNMP community name to which the library belongs.
vName - Unique SNMP name for the system.
vLocation - Physical location of the system.
vContact - Contact person's name.
vSNMPv3 engine ID - A read-only attribute that identifies the SNMPv3
engine.
5. Enter the trap IP addresses of the SNMP monitoring stations to be notified
when an event takes place and the security settings in the Trap List menu.
a29z0128
Figure 39. Trap notifications
42 Dell PowerVault TL1000 Tape Autoloader: User's Guide
vValidity - Enable/Disable setting.
vTrap version - v1, v2c, or v3. For v2c and v3, the Inform check box
determines whether an SNMP INFORM request is sent instead of a trap
event.
vIP address - IPv4 and IPv6 addresses are supported. Host names can be
entered instead of numerical IP addresses if the DNS server is specified.
vCommunity (v1 or v2c) - SNMP community name.
vUser name (v3 only) - SNMPv3 unique user name.
vAuthentication (v3 only) - Authentication algorithm, MD5, or SHA. When an
algorithm is specified, an authentication password and confirmation of the
password are required.
vPrivacy (v3 only) - Privacy service encryption and decryption algorithm, DES
or AES. When an algorithm is specified, a privacy password and
confirmation of the password are required.
6. Enter the SNMPv3 users who are allowed to access the tape library in the
SNMPv3 User List menu.
vValidity - Enable/Disable setting.
vUser name - SNMPv3 unique user name.
vAuthentication - Authentication algorithm, MD5, or SHA. When an
algorithm is specified, an authentication password and confirmation of the
password are required.
a29z0140
Figure 40. Trap list settings
a29z0141
Figure 41. SNMPv3 user list settings
Chapter 3. Installation and configuration 43
vPrivacy - Privacy service encryption and decryption algorithm, DES or AES.
When an algorithm is specified, a privacy password and confirmation of the
password are required.
7. Select the event level to report in the Trap event field.
8. Click Test to send a test trap notification to the enabled IP addresses.
9. Click Submit to enable the settings.
Managing user access
Note: This procedure is optional.
Add, modify, or remove users with the following information:
vSelect action
–Add - To add new users.
- Enter the user name and password into the dialog box and assign the
user's role.
a29z0122
Figure 42. User access settings
44 Dell PowerVault TL1000 Tape Autoloader: User's Guide
- Click Submit to save the new user, Cancel to remove the user, or Clear to
remove the information and start over.
–Modify - To change the selected user’s access role or password.
–Remove - To delete the selected user from the system.
vUser Name - The user name of a registered user.
vRole - The user access level for the registered user.
–Users are allowed to monitor the library, but not complete actions that affect
the physical library.
–Superusers are allowed to operate the physical and logical library, but not
complete actions that affect the library configuration.
–Administrator users are allowed access to the entire physical library and
logical library, including configuration. Only one administrator user must be
assigned the login name admin.
vPassword indicates the status of the user's password.
–Expired: The maximum password age was exceeded. The password is now
invalid.
–Unchangeable: The minimum password age was not exceeded. You cannot
change the password.
–Available: The password is available to be changed.
–Locked: The maximum number of failed login attempts for the account was
exceeded. An administrator must unlock the account.
An administrator can add/modify/remove extra administrator, superuser, and user
accounts, and change passwords. User accounts are restricted to specific areas of
the library. For more information, see Chapter 2, “User interfaces,” on page 13.
A User account can be modified by an administrator to provide a user with
superuser or administrator access permissions to the library functions.
Enter all user IDs and passwords on the Library Configuration form in “Library
Configuration Form” on page 153.
Click Submit to transfer the settings to the library. A dialog message is displayed
when the settings are updated successfully.
Click Refresh to read the current settings from the library.
a29z0139
Figure 43. Add User dialog box
Chapter 3. Installation and configuration 45
Configuring Password Rules Settings
The Password Rules tab displays the rules for user passwords.
vMinimum number of characters - Choose the minimum password length. The
factory default value is 8. The maximum password length is 16.
vMinimum number of upper case alphabetic characters (A-Z) - Choose the
minimum number of uppercase alphabetic characters. The factory default value
is 1.
vMinimum number of lower case alphabetic characters (a-z) - Choose the
minimum number of lowercase alphabetic characters. The factory default value
is 1.
vMinimum number of numeric characters (0-9) - Choose the minimum number
of numeric characters. The factory default value is 1.
vMinimum number of special characters (!@#$%^&*()_+={}|[]\;':"<>?,./) -
Choose the minimum number of special characters. The factory default value is
0.
vMaximum number of identical consecutive characters - Choose the maximum
number of identical consecutive characters. The factory default value is 2. There
is no limitation if 0 is selected.
vMaximum number of failed logins before password is locked - Choose the
maximum number of failed logins before the password is locked. The factory
default value is 5. Possible range for this configuration option is 0 - 10. There is
no limitation if 0 is selected.
vMaximum number of days before password must be changed - Choose the
maximum number of days before the password must be changed. There is no
limitation if 0 is selected.
vMinimum number of days before password can be changed - Choose the
minimum number of days before the password can be changed. A password can
be changed immediately if 0 is selected.
a29z0205
Figure 44. Password Rules screen
46 Dell PowerVault TL1000 Tape Autoloader: User's Guide
vNumber of password changes before an old password can be used again -
Choose the number of password changes that are required before a password
can be used again. A password can be reused immediately if 0 is selected.
Click Submit to save all the information.
Click Refresh to display the current password settings.
Saving the library configuration
Note: This procedure is recommended.
Each time that you change the configuration of your library, save the configuration.
This function also maintains several library configuration profiles that can be
restored to the library when wanted with the Web User Interface.
To save library configuration:
1. Expand Configure Library, if necessary, and click Save/Restore in the left
navigation pane of the Web User Interface.
2. Click Save to create a configuration file of your library on your computer.
Configuring your library with the Operator Panel
To configure your library with the Operator Panel, complete the following
procedures:
1. “Logging in to the Operator Panel”
2. “Configuring network settings”
3. “Configuring library settings” on page 49
Logging in to the Operator Panel
In many environments, the default network settings might be sufficient to access
your tape library on a network. To change the default network settings with the
Operator Panel, complete the following procedure:
1. When the library is initialized, press Enter to move to the Password screen.
2. Enter 0000, the default password. The top menu screen displays.
3. When finished with the Operator Panel, press Cancel to return to the top menu
screen.
4. When finished, press the Minus key to select Logout, and press Enter.
Configuring network settings
In many environments, the default network settings might be sufficient to access
your tape library on a network. To change the default network settings with the
Operator Panel, complete the following procedure:
1. From the top menu screen, press the Minus key to select Configuration, and
press Enter.
2. Link speed (Default: Auto Negotiation)
a. Select Configure Network Settings > Configure Link Speed.
a29z0129
Figure 45. Save configuration
Chapter 3. Installation and configuration 47
b. Select the required speed and press Enter.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
The speed must be set to Set Auto Negotiation for gigabit Ethernet
networks.
d. Press Cancel to backtrack through the menu hierarchy.
3. DHCP IPv4 (Default: Enabled)
a. Select Configure Network Settings > Configure DHCP > Configure
DHCPIPv4.
b. Select Enable DHCP IPv4 and press Enter to enable, or press Down and
select Disable DHCP IPv4 to disable.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
4. DHCP IPv6 (Default: Disabled)
a. Select Configure Network Settings > Configure DHCP > Configure
DHCPIPv6.
b. Select Enable DHCP IPv6 and press Enter to enable, or press Down and
select Disable DHCP IPv6 to disable.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
5. IPv4/IPv6 Address (Default: 0.0.0.0). If DHCP is disabled, set the IP address
manually.
a. Select Configure Network Settings > Change IP Address.
b. Select Set IP Address IPv4 to enter the IPv4 address of the tape library.
Set IP Address IPv6 to enter the IPv6 IP address (split over 4 screens).
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
6. IPv4 Subnet Mask (Default: 255.255.255.0). If DHCP IPv4 is disabled, set the
IPv4 subnet mask manually.
a. Select Configure Network Settings > Change Subnet Mask > Set Subnet
Mask.
b. Enter the IPv4 subnet mask.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
7. IPv6 Prefix Length (Default: 64). If DHCP IPv6 is disabled, set the IPv6 prefix
length manually.
a. Select Configure Network Settings > Change Subnet Mask > Set Prefix
Length.
b. Enter the IPv4 prefix length.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
8. IPv4/IPv6 Gateway (Default: 0.0.0.0). If DHCP is disabled, set the IP address
manually.
a. Select Configure Network Settings > Change Gateway.
b. Select Set Gateway Address IPv4 to enter the IPv4 gateway address or Set
Gateway Address IPv6 to enter the IPv6 gateway address (split over 4
screens).
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
48 Dell PowerVault TL1000 Tape Autoloader: User's Guide
9. Press Cancel to return to the Network Settings menu.
10. Press Cancel to return to the Configuration menu.
11. Press Cancel to return to the top menu screen.
Configuring library settings
To configure the library settings, complete the following procedure:
1. From the top menu screen, press the Minus key to select Configuration, and
press Enter.
2. Select Configure Library, and press Enter.
3. I/O Station (Default: Disabled)
a. Select Configure Library > Configure I/O Station.
b. Select Enable I/O Station to enable the 1-slot I/O station or Disable I/O
Station to disable.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
4. Active Slots (Default: All)
a. Select Configure Library > Set Active Slots Count.
b. Select the number of active slots you would like to assign for the logical
library.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
5. Library Mode (Default: Random)
a. Select Configure Library > Configure Library Mode.
b. Select Set Random Mode or Configure Sequential Mode, and press Enter.
Random - In random mode, the library allows the server's (host's)
application software to select any data cartridge in any order.
Sequential - In sequential mode, the library's firmware predefines the
selection of the cartridges. After initialization, the firmware causes the
library to select the first available cartridge found (counting from the lowest
Column/Tier position through the highest cartridge position in your library)
for loading into the drive.
vLoop - Sequential mode with loop mode ON loads the cartridge in the
lowest Column/Tier cartridge position after the cartridge in the highest
Column/Tier cartridge position is filled with data and sent back to its
home position. This procedure allows endless backup operations without
user interaction.
vAutoload - Sequential mode with autoload mode ON loads the first
available cartridge (the lowest Column/Tier cartridge position that
contains a cartridge) automatically if the library powers ON, or resets,
with an empty drive. If the library powers ON with a cartridge already in
the drive, sequential mode starts from the home position of that
cartridge, unless the host issues a rewind and unload command to the
drive. In which case the next cartridge in sequence is loaded into the
drive.
To start sequential mode if autoload is OFF, use the Move Cartridge
command to load the first cartridge into the drive. The sequence starts from
the home position of that cartridge. Cartridges need not to be in contiguous
slots.
To stop sequential mode, use the Move Cartridge command to unload the
drive. This command cancels sequential mode; the next sequential cartridge
is NOT loaded.
Chapter 3. Installation and configuration 49
To restart sequential mode, use the Move Cartridge command again to load
a cartridge; the loading sequence resumes from the home position of that
cartridge.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
6. Date/Time - Enter the local time and date manually if you do not plan to use a
network-based time server.
a. Select Configure Library > Configure Date/Time.
b. Select Set Date or Set Time, and press Enter.
vDate - Enter the date with the MM/DD/YYYY format.
vTime - Enter the time with the HH:MM:SS format.
c. Press Cancel to backtrack through the menu hierarchy.
7. Auto Cleaning (Default: Disabled)
a. Select Cofiguration > Configure Auto Cleaning.
b. Select Enable Auto Cleaning or Disable Auto Cleaning, and press Enter.
The Auto Cleaning function is enabled only if there is at least one inactive
position in the magazine in the library.
c. Press Enter again to apply the setting, or Cancel to reject the setting.
d. Press Cancel to backtrack through the menu hierarchy.
Populating the library with cartridges
The magazine is opened with the Operator Panel.
To populate the library with data and cleaning cartridges, complete the following
procedure:
1. From the top menu screen on the Operator Panel, press the Minus key to select
Unlock Magazine, and press Enter, or from Web User Interface: Manage
Library > Unlock Magazine.
2. Insert cartridges in the magazine.
Note: A blue release gate (▌1▐in Figure 46) in the upper left corner of each
column in the cartridge magazine prevents each cartridge from falling out of
the front of the magazine. When manually releasing the gate with one hand,
position your other hand in front of the column opening to protect cartridges
that are ejected by the internal column spring.
Note: Column 5 Tier 2 is reserved as the exchange position. This position is
accessible by the library only. A locking mechanism prevents insertion of a
cartridge into the reserved slot.
a29z0101
1
Figure 46. Cartridge release gate
50 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Each cartridge must be inserted with the indicator arrow on the leading edge of
the upper surface of the cartridge pointing towards the cartridge magazine (see
Figure 47).
Note: Do not rely on the bar code label orientation, if attached, to provide an
indication of the correct cartridge orientation. The bar code label is right side
up if attached correctly.
The Auto Cleaning function can be enabled only if the number of active slots is
less than the maximum available slots. The active slots are always enabled
starting with the lowest numerical cartridge position number in the magazine.
This position is at the drive end of the cartridge magazine. Place cleaning
cartridges in inactive cartridge positions for use by the auto cleaning function.
Do not store data or cleaning cartridges in the I/O Station (Column 5, Tier 1) if
the I/O station is enabled.
3. Put the magazine back into the library and wait for the library inventory to
complete. Then, you can proceed to the next step.
4. Press Cancel to return to the top-level menu.
Verifying library and drive operation
To verify the library is operating correctly:
1. From the top menu screen on the Operator Panel, press the Minus key to select
Service, and press Enter.
2. Press the Minus key to select Diagnostics, and press Enter.
3. Select Run Library Verify, and press Enter. Follow the on-screen instructions.
If there is a cartridge in a drive, the library moves the cartridge to its home
position, or to the I/O station if the home position is not known.
4. When prompted, insert a customer supplied scratch cartridge into the I/O
station.
When the scratch cartridge is loaded, the bar code reader reads the bar code
label on the cartridge and stores it for later comparison. The cartridge is then
a29z0056
LTO123L4
Figure 47. Cartridge orientation
Chapter 3. Installation and configuration 51
moved to the tape drive, where the drive runs its own write/read/verify test.
When the test is done, the library tells the drive to eject the cartridge, and then
the cartridge is moved back to the I/O station. The bar code is read again and
compared with the value stored earlier.
5. When prompted, remove the cartridge from the I/O station.
The result of the test is reported on the Operator Panel.
If an error occurs, note the error code number and see “Error codes” on page
123.
6. Press Cancel to return to the top-level menu.
Taking the Library Online
When your library is configured, you are ready to save the library configuration
and take the library online.
Note: The tape drive is always online, regardless of whether the library is online
or offline.
To take the library online with the Operator Panel:
1. From the top menu screen, press the Minus key to select Commands, and press
Enter.
2. Select Change Library State, and press Enter.
3. Select Set Library Online, and press Enter.
4. Press Cancel repeatedly to return to the top-level menu.
5. Press the Minus key to select Logout, and press Enter.
To take the library online with the Web User Interface:
1. Save the library configuration.
a. Expand Configure Library, if necessary, and click Save/Restore in the left
navigation pane of the Web User Interface.
b. Click Save, and then enter a file name and select a location to save the
configuration file.
2. Verify the library state.
a. Click Library State in the left navigation pane of the Web User Interface.
b. If the library is offline, click Bring Online.
c. Click Yes to confirm when prompted.
A message dialog displays when the operation is completed.
3. Click Logoff in the upper right corner of the window.
Registering for support notification
Support notification registration provides email notification when new firmware
levels are updated and are available for download and installation.
Enter your user name and password on the “Library Configuration Form” on page
153.
Note: Library firmware and tape drive firmware are verified and released together.
When the latest firmware is updated, verify that all installed components such as
52 Dell PowerVault TL1000 Tape Autoloader: User's Guide
the tape drive and library are at the latest levels noted on the Support website.
Mixing different levels of library and tape drive firmware is not supported and
might cause unpredictable results.
Dell suggests that you update library and drive firmware when new levels become
available. For instructions on updating library and drive firmware, see “Updating
library and drive firmware” on page 93.
Now you are ready to use your library.
Chapter 3. Installation and configuration 53
54 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Chapter 4. Operations
“The Operator Panel” on
page 56
Monitoring the Library “Configuration settings” on page 57
“Current information” on page 57
“Firmware revision” on page 58
Managing the Library “Unlocking the I/O station” on page 58
“Unlocking the cartridge magazine” on page 59
“Moving cartridges” on page 59
“Unloading the drive” on page 60
“Cleaning the drive manually” on page 60
“Conducting a library inventory” on page 60
“Taking the library online and offline” on page 61
“Powering down the library” on page 61
“Shipping the library” on page 61
“Rebooting the drive” on page 62
“Rebooting the library” on page 62
“Logging out of the library” on page 62
Configuring the Library “Configuring auto cleaning” on page 62
“Configuring the number of active slots” on page 63
“Configuring the library access mode” on page 63
“Configuring date and time settings” on page 64
“Configuring network settings” on page 65
“Configuring Operator Panel settings” on page 66
“Configuring Web GUI Settings” on page 66
“Setting the library to factory defaults” on page 67
Servicing the Library “Checking the library error status” on page 67
“Running library verify diagnostic procedures” on
page 67
“Running drive diagnostic procedures” on page 68
55
“The Web User
Interface” on
page 69
Monitoring the Library “The system summary” on page 70
“The library map” on page 71
Managing the Library “Moving cartridges” on page 73
“Unloading the drive” on page 74
“Cleaning the drive manually” on page 74
“Taking the library online and offline” on page
74
“Conducting a library inventory” on page 75
“Unlocking the cartridge magazine” on page 75
Configuring the Library “Managing user access” on page 76
“Configuring physical library settings” on page
79
“Configuring logical library settings” on page
79
“Configuring network settings” on page 81
“Configuring encryption settings” on page 82
“Configuring date and time settings” on page
84
“Configuring email notifications” on page 85
“Configuring SNMP trap notifications” on page
86
“Saving and restoring configuration settings”
on page 88
“Operator
interventions” on page
89
“Library logs” on page
90
“Trace data” on page 91
“Downloading drive
logs” on page 92
“Downloading library
logs” on page 92
“Resetting the library
and drives” on page 92
“Updating library and
drive firmware” on
page 93
“Accessor statistics” on
page 94
The Operator Panel
Figure 48 on page 57 shows the top-level menu tree structure of the Operator Panel
on the front of the TL1000 Tape Autoloader. For details on how to select
commands and options, see the description in “Operator Panel” on page 13.
56 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Monitoring the library
Configuration settings
Use Configuration > View Settings to display a list of the library configuration
settings.
The settings that are displayed include:
vLibrary settings
– I/O station (On/Off)
– Auto cleaning (On/Off)
– Number of cleaning slots when Auto cleaning is enabled
– Operator Panel back light setting
vNetwork settings
– Link speed
– IP address protocol
– IPv4 settings (IP address, subnet mask address, gateway address, DHCP)
– IPv6 settings (IP address, gateway address, prefix length, DHCP, stateless
Auto configuration)
vDrive settings
– Model number
Current information
Use View Current Information to display the network settings information.
Top Level Commands Service
Configuration
Unlock I/O Station*
Unlock Magazine
Commands
Configuration
View Current Information
Service
Logout
* If enabled.
Move Cartridge
Unload
Clean Drive
Inventory
Move to Ship Position
Reboot Drive
Reboot Library
Change Library State
Configure Library
Configure Auto Cleaning
Configure Network Settings
Configure Op Panel Settings
View Settings
Set Default
View Error Status
Diagnostics
View Firmware Revision
Telnet Service Port*
* For use by technical
support personnel only.
a29z0064
Figure 48. Operator Panel top menus
Configuration
ViewSettings
Figure 49. Configuration settings
ViewCurrentInformation
Figure 50. Current information
Chapter 4. Operations 57
The settings that are displayed include:
vNetwork settings
– Worldwide node name
– IP address protocol stack
– IP address
Firmware revision
Select Service > View Firmware Revision to display the current version of the
library firmware.
Managing the library
Unlocking the I/O station
Select Unlock I/O Station to unlock the I/O station. This menu option is available
only when the I/O station is enabled in the library configuration settings.
After the I/O station is closed, wait for the library to complete its inventory before
you proceed with normal library operations.
Service
ViewFirmwareRevision
Figure 51. Firmware revision
UnlockI/OStation
Figure 52. Unlock I/O station command
a29z0024
Figure 53. I/O station unlocked
58 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Note: A blue release gate in the upper left corner of each column in the cartridge
magazine prevents each cartridge from falling out of the front of the magazine.
When manually releasing the gate with one hand, position your other hand in
front of the column opening to protect cartridges that are ejected by the internal
column spring.
Unlocking the cartridge magazine
Select Unlock Magazine to unlock and remove the cartridge magazine.
When the cartridge magazine is unlocked, it can be removed from the library to
insert or remove data and cleaning cartridges. When the cartridge magazine is
fully inserted, the magazine locks into place.
After the magazine is closed, wait for the library to complete its inventory before
you proceed with normal library operations.
Note: A blue release gate in the upper left corner of each column in the cartridge
magazine prevents each cartridge from falling out of the front of the magazine.
When manually releasing the gate with one hand, position your other hand in
front of the column opening to protect cartridges that are ejected by the internal
column spring.
Moving cartridges
Select Commands > Move Cartridge to move data cartridges and cleaning
cartridges between the I/O station, storage positions, and tape drive.
Specify the following parameters:
vSource Slot - Specify a source that contains a cartridge.
vDestination Slot - Specify the destination.
Press the Enter key to move the cartridge from the source to the destination.
Note: Cartridges cannot be moved to the accessor with this command, but can be
moved from the accessor if, for example, the library was powered OFF with a tape
still held in the Picker.
UnlockMagazine
Figure 54. Unlock magazine command
Commands
MoveCartridge
SourceSlot
DestinationSlot
Figure 55. Move cartridge command
Chapter 4. Operations 59
Unloading the drive
Select Commands > Unload to unload the cartridge from the tape head
mechanism.
Unload when library is in Random mode: The cartridge in the drive is unloaded
from the tape head mechanism, but is still retained inside the tape drive housing.
The Move Cartridge command moves the cartridge from the drive to another
location. Moving a tape cartridge from a drive to another location both unloads
and moves the cartridge in a single action.
Unload when library is in Sequential mode: The cartridge in the drive is unloaded
from the tape head mechanism, and returned to the cartridge home position.
Press the Enter key to unload the cartridge from the tape head mechanism.
Cleaning the drive manually
Select Commands > Clean Drive to clean the tape drive manually with a cleaning
cartridge in either a cartridge storage position or the I/O station.
Press the Enter key to move the cleaning cartridge to the drive and start drive
head cleaning. The cleaning cartridge is returned to its home position when drive
cleaning is finished.
Conducting a library inventory
Select Commands > Inventory to force the library to run an inventory of the
cartridge magazine, accessor, and tape drive to refresh the library map. An
inventory is conducted automatically when power is first turned ON or when the
cartridge magazine is removed and reinserted.
Press the Enter key to conduct the inventory.
Commands
Unload
Figure 56. Unload command
Commands
CleanDrive
Figure 57. Clean Drive command
Commands
Inventory
Figure 58. Inventory command
60 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Taking the library online and offline
Select Commands > Change Library State to take the library online or offline.
It is sometimes necessary to take the library offline before servicing functions for
the library are done. Once these operations are finished, it is necessary to bring the
library online.
Note: The tape drive is always online, even when the library is offline.
Powering down the library
Before powering OFF the library, ensure that the library is in an idle state with no
mechanical movement of the accessor, and all data operations (for example, backup
operations, accessing of log files) are complete. Then, power OFF the library with
the power switch on the rear panel of the library.
Important: If you switch the library power OFF while the library is being
accessed, loss of data might occur.
Note: When power cycling the library, wait 10 seconds after the power is OFF
before the library is powered ON again.
Shipping the library
Select Commands > Move to Ship Position when the library is prepared to move
to a new location. The accessor must be placed in a parked position within the
library housing. Move to Ship Position finishes all active commands that are
received from the host application, does not process any new commands, and
moves the accessor to the parked position before the power is turned OFF.
1. When Unlock Magazine is displayed, press the Enter key to unlock the
cartridge magazine. The magazine unlocks and the display prompts the
removal of the magazine.
2. Remove all cartridges from the magazine and reinsert the magazine into the
slide mechanism. The library completes an inventory to verify no cartridges are
in the magazine.
3. If the magazine is empty, the library moves the accessor to the ship position.
The library can be powered down. If the magazine is NOT empty, the library
prompts to remove cartridges. After all cartridges are removed and the
magazine is replaced, start the ship position process again.
Commands
ChangeLibraryState
SetLibraryOnline
SetLibraryOffline
Figure 59. Online/Offline command
Commands
MovetoShipPosition
Figure 60. Move to Ship Position command
Chapter 4. Operations 61
Rebooting the drive
Select Commands > Reboot Drive to force the drive to reboot. You also specify
whether the library will come online or offline after it finishes rebooting.
Press the Enter key to reboot the drive.
Rebooting the library
Select Commands > Reboot Library to force the library to reboot. You also specify
whether the library will come online or offline after it finishes rebooting.
Press the Enter key to reboot the library.
Logging out of the library
Select Logout to log out of the library. The login screen is displayed for the next
user.
Configuring the library
Configuring auto cleaning
Select Configuration > Configure Auto Cleaning to enable or disable automatic
head cleaning of the tape drive in the library.
Note: It is recommended that the Auto Clean function is enabled on the library.
With the Auto Clean function enabled, drive cleaning occurs automatically. The
only time Auto Cleaning is disabled is when your Backup Application requires that
it has control.
Commands
RebootDrive
Figure 61. Reboot Drive command
Commands
RebootLibrary
Figure 62. Reboot Library command
Logout
Figure 63. Logout command
Configuration
Configure AutoCleaning
Enable AutoCleaning
Disable AutoCleaning
Figure 64. Auto Cleaning settings
62 Dell PowerVault TL1000 Tape Autoloader: User's Guide
The drive can also be cleaned manually. For details, see “Cleaning the drive
manually” on page 60.
Configuring the number of active slots
Select Configuration > Configure Library > Set Active Slots Count to set the
number of active data cartridge positions within the logical library.
Configure the number of active slots with the following setting:
vActive Slots - The maximum number of active slots that can be set is dependent
upon the I/O station configuration and auto cleaning setting.
The active cartridge slots always begin with the cartridge position with the lowest
cartridge address within the logical library.
Configuring the library access mode
Select Configuration > Configure Library > Configure Library Mode to set the
logical library access mode.
Configure the library access mode with the following settings:
vRandom Mode - In random mode, the library allows the server's (host's)
application software to select any data cartridge in any order.
vSequential Mode - In sequential mode, the library's firmware predefines the
selection of the cartridges. After initialization, the firmware causes the library to
select the first available cartridge found (counting from the lowest Column/Tier
position through the highest cartridge position in your library) for loading into
the drive.
Configuration
ConfigureLibrary
Set ActiveSlotsCount
ActiveSlots
Figure 65. Active slot count settings
Configuration
ConfigureLibrary
ConfigureLibraryMode
SetRandomMode
SetSequentialMode
ConfigureLoopMode
EnableLoopMode
DisableLoopMode
Configure AutoloadMode
Enable AutoloadMode
Disable AutoloadMode
Figure 66. Library access mode settings
Chapter 4. Operations 63
–Loop - Sequential mode with loop mode ON loads the cartridge in the lowest
Column/Tier cartridge position after the cartridge in the highest Column/Tier
cartridge position is filled with data and sent back to its home position. This
mode allows endless backup operations without user interaction.
–Autoload - Sequential mode with autoload mode ON loads the first available
cartridge (the lowest Column/Tier cartridge position that contains a cartridge)
automatically if the library powers ON, or resets, with an empty drive. If the
library powers ON with a cartridge already in the drive, sequential mode will
start from the home position of that cartridge, unless the host issues a rewind
and unload command to the drive, in which case the next cartridge in
sequence will be loaded into the drive.
To start sequential mode if autoload is OFF, use the Move Cartridge command to
load the first cartridge into the drive. The sequence starts from the home
position of that cartridge. Cartridges do not need to be in contiguous slots.
To stop sequential mode, use the Move Cartridge command to unload the drive.
This mode cancels sequential mode; the next sequential cartridge is NOT loaded.
To restart sequential mode, use the Move Cartridge command again to load a
cartridge; the loading sequence resumes from the home position of that
cartridge.
Configuring date and time settings
Select Configuration > Configure Library > Configure Date/Time to set the date
and time on your library manually after a power disruption and when daylight
saving time starts and ends. The date is set in MM/DD/YYYY format, and the
time is set in 24-hour HH:MM:SS format.
The current date and time is also controlled automatically with a network-based
Network Time Protocol (NTP) server. For more information, see “Configuring
network settings” on page 65.
Configuration
ConfigureLibrary
ConfigureDate/Time
SetDate
Set Time
Figure 67. Date and time settings
64 Dell PowerVault TL1000 Tape Autoloader: User's Guide
Configuring network settings
Select Configuration > Configure Network Settings to set the network settings for
the library.
Note: The Internet Protocol (IPv4, IPv6, or dual IPv4/IPv6) selection is used for
the TL1000 Tape Autoloader IP address, subnet mask, gateway address, time server
address, mail server address, SNMP trap address, and EKM server addresses.
Configure the network with the following settings:
vLink Speed - Ethernet duplex mode (Auto, 10Base-T Full, 10Base-T Half,
100Base-TX Full, 100Base-TX Half).
vDHCP - (Dynamic Host Configuration Protocol) Enable DHCP to have the
library server or router negotiate the connection with the library.
–IPv4 - Select to enable DHCP with the IPv4 protocol.
–IPv6 - Select to enable DHCP with the IPv6 protocol
vIP Address - If DHCP is disabled, set the IP address of the library manually.
Configuration
ConfigureNetworkSettings
ConfigureLinkSpeed
Set AutoNegotiation
Set10Base-T Full
Set10Base-T Half
Set100Base-T Full
Set100Base-T Half
ConfigureDHCP
ConfigureDHCP IPv4
EnableDHCP IPv4
DisableDHCP IPv4
ConfigureDHCP Ipv6
EnableDHCP IPv6
DisableDHCP Ipv6
SetIP AddressIpv4
ChangeIP Address
SetIP AddressIpv6
InputIP Address
InputIP Addressx4
ChangeSubnetMask
SetSubnetMask
SetPrefixLength
InputSubnetMask
InputPrefix
ChangeGateway
SetGateway AddressIpv4
SetGateway AddressIpv6
InputGateway
InputGatewayx4
Figure 68. Network settings
Chapter 4. Operations 65
–IPv4 - Select to enter the library IP address with the IPv4 protocol.
–IPv6 - Select to enter four library IP addresses with the IPv6 protocol.
vSubnet Mask - If DHCP is disabled, set the IP address of the subnet mask.
–Subnet Mask - Select to enter the subnet mask address with the IPv4
protocol.
–Prefix Length - Select to enter the prefix length for the IPv6 protocol.
vGateway - If DHCP is disabled, set the IP address of the gateway.
–IPv4 - Select to enter the gateway IP address with the IPv4 protocol.
–IPv6 - Select to enter four gateway IP addresses with the IPv6 protocol.
Configuring Operator Panel settings
Select Configuration > Configure Op Panel Settings to set the preferences when
with the Operator Panel.
Configure the Operator Panel with the following settings:
vBack light - Select to enable the LCD back light when with the Operator Panel.
–Input Count - If the auto back light is enabled, specify the time duration
before the back light turns OFF. The setting uses a four-digit timer in minutes.
vLogin Password - Select to change the Operator Panel four-character login
password. The new password must be reentered for confirmation before the
password is changed (default: 0000).
Configuring Web GUI Settings
Use Configuration > Configure Web GUI Settings > Unlock a User Account to
unlock a User Account.
Configuration
ConfigureOpPanelSettings
ConfigureLCDBackLight
Enable AutoBackLight
InputCount(min)
Disable AutoBackLight
ChangeLoginPassword