Eaton EATS16 User Manual

Displayed below is the user manual for EATS16 by Eaton which is a product in the Power Distribution Units (PDUs) category. This manual has pages.

Related Manuals

Eaton 9SX11KiPM Manual

Eaton 9SX8KiPM Manual

Eaton 9SXEBM240 Manual

Eaton 9PX11KPM Manual

Eaton 5E650iUSB Manual

Eaton 5E500i Manual

Eaton 5E650I Manual

Eaton 5E850iUSB Manual

ENGLISH

EATS16

EATS16N

Installation

and user manual

Service and support:

Call your local service representative

EATS16_EN

Page 2 EATS16_EN

SAVE THESE INSTRUCTIONS. This manual contains important instructions

that should be followed during installation and maintenance of the ATS.

The EATON ATS models that are covered in this manual are intended for installation

in an environment within 0°C to 40°C (32°F to 104°F) and free of conductive contaminant.

Certication standards

• Safety:IEC62310-1

• EMC:IEC62310-2

• Performance:IEC62310-3

• CEMark

• Additionalconformances:

- IEC60950-1

- CISPR22ClassB

Important safety notes

• Onlyqualiedpersonnelcanservicethisequipment.

• Followthefollowingprecautionswhenworkingonthisunit.

- Removewatches,rings,orothermetalobjects.

- Usetoolswithinsulatedhandles.

• Examinethepackingcontainer.Notifythecarrierimmediatelyifanydamageispresent.

• Donotdisassembletheunit.

• Do not operate the unit near water or in an area with excessive humidity.

• Keepliquidandforeignobjectsfromgettinginsidetheunit.

• Donotoperatetheunitclosetogasorre.

• Verifywhetherthebranchcircuitbreakerorfuseonservicefeediscorrect.

• Verify line voltage requirements and the supplied line voltage prior to installation.

• Thisunitissuppliedfrommultiplesources,disconnectallsourcesbeforeservicing.

Electrical warnings

• Checkthatpowercords,plugs,andoutletsareingoodcondition.

• RAL equipment:"EquipmentintendedforinstallationinRestrictedAccessLocation".

Warning

• Intendedtobeconnectedtocomputerload.

• Nottobeconnectedtoinductiveloadorwith>3:1crestfactorload.

SAFETY INSTRUCTIONS

Page 3

EATS16_EN

ENGLISH

Contents

1. Introduction ....................................................................................... 4

2. Presentation ...................................................................................... 4

2.1 Weights and dimensions ...............................................................................................4

2.2. Rear panel layout - EATS16 - EATS16N ..........................................................................4

2.3 Control panel ..................................................................................................................4

2.4 LCD description .............................................................................................................5

2.4.1 Power ow ..................................................................................................................... 5

2.4.2 Measures ....................................................................................................................... 6

2.5 ATS settings ...................................................................................................................6

2.6 Warning ..........................................................................................................................8

3. Installation for ATS ........................................................................... 9

3.1 Checking the accessory kit - EATS16 - EATS16N ...........................................................9

3.2 Storage ........................................................................................................................10

3.3 Installation for rack mounting (normal installation) ......................................................10

3.4 Installation for rack mounting (2 post installation) .......................................................10

3.5 Wall installation ............................................................................................................ 10

3.5 Instructions ................................................................................................................. 11

4. Power cables connection ............................................................... 12

4.1 Installation diagram ......................................................................................................12

4.2 Input/Output connection EATS16 - EATS16N...............................................................12

5. Communication .............................................................................. 13

5.1 Communication ports: EATS16N .................................................................................13

5.2 Eaton Intelligent Power Software suite .......................................................................14

6. Maintenance ................................................................................... 15

6.1 Troubleshooting ...........................................................................................................15

7. Specications .................................................................................. 16

Page 4 EATS16_EN

1. Introduction

TheEATONAutomaticTransferSwitch(ATS)isahighavailabilityswitchdesignedforprovidingredundant

powerforsensitiveequipment.Itispoweredbytwoindependentpowersourcesandautomaticallymakes

a rapid switch from one source to the other when the power supply used to power its connected load fails.

ThisATSisdesignedtobeefcientandreliable.

UserscanknowEATONATS’spowerow,status,parametersfromtheLCDinterface.Besides,the

EATS16Nunithasanetworkinterfaceforuserstoreadandwriteparameters.Thenetworkinterfacecanbe

implementedviatheEthernetprotocolthroughanRJ45connector.

2. Presentation

2.1 Weights and dimensions

Rack installation

Description Weights

(kg / lb)

Dimensions H x W x D

(mm / inch)

EATS16 3.32/7.31 43 x 438 x 250/1.7x17.24x9.84

EATS16N 3.54/7.8 43 x 438 x 250/1.7x17.24x9.84

2.2. Rear panel layout - EATS16 - EATS16N

143 3 1 InputSource1:IECC20inlet

2 InputSource2:IECC20inlet

3 Output:8xC1310A

4 Output:1xC1916A

2.3 Control panel

TheATShasthreebuttonsonthecontrolpanelandaLCDdisplay.Itprovidesusefulinformationaboutthe

ATSitself,loadstatus,events,measurementsandsettings.

1 LCDpanel

2 Navigation:Scrolldownbutton

3 Navigation:Enterbutton

4 Navigation:Escapebutton

5 TransferTest:ScrolldownandEnter

buttonspressedfor5s

Page 5

EATS16_EN

ENGLISH

2.4 LCD description

1Power flow 3ATS Settings

2Measures/Infos 4Events

2.4.1 Power ow

S1isdefinedastheprioritysource(truebydefault)

S2isdefinedastheprioritysource(canbeset)

S1 not powered

S2 not powered

S1 powering the load

S2 powering the load

S1poweredbutnotpoweringtheload

S2poweredbutnotpoweringtheload

Transfer from S1 to S2

Transfer from S2 to S1

Transfer from S1 to S2 for Test

Transfer from S2 to S1 for Test

2. Presentation

Page 6 EATS16_EN

2. Presentation

2.4.2 Measures

Output current

(default display)

Output voltage

Input voltage : S1

(default display only when S1 voltage is out of tolerance)

Input frequency: S1

(default display only when S1 frequency is out of tolerance)

Input voltage : S2

(default display only when S2 voltage is out of tolerance)

Input frequency: S2

(default display only when S2 frequency is out of tolerance)

S1 and S2 phase shift

(availableonlywhenS1andS2arenotsynchronized)

2.5 ATS settings

OUTPUT: Sets voltage thresholds

200V-208V-220V-230 V (default)-240V

ALARM:Silentsalarm

ON:normalbeepinwarningorfaultmode,bydefault

OFF:silent.

SENSITIVITY (mainly for LIA UPS):Sets

Sensitivity mode for input mains detection.

Std:NormalSensitivity,bydefault

Lo:LowSensitivity,forcompatibilitywithdistorted

waveform.

P SOURCE:Setstheprioritysource Sc.1:PriorityonSource1,bydefault

Sc.2:PriorityonSource2

TRANSFER: Std:noadditionalbreakevenifS1andS2arenot

synchronized,bydefault

Gap:additionalbreakduringtransferifS1andS2are

notsynchronized.

Page 7

EATS16_EN

ENGLISH

2. Presentation

Press Enter to reach settings menu

To cancel the changes

To select value

OUTPUT

ALARM

SENSITIVITY

PRIORITY SOURCE

TRANSFER

Page 8EATS16_EN

2.6 Warning

ForFault,refertotroubleshootingsection6.1.

Event Example of displays Rootcause

Overload

Loadisovernominalrating

Removesomeoftheequipmentfrom

theATS.TheATScontinuestooperate,

butmayshutdowniftheloadincreases.

The alarm resets when the condition

becomesinactive.

Unsynchronizedsources OnesourceNandLarereversed

S1ansdS2arefedbydifferentphase

(L1/L2/L3)

S1 and S2 frequency are different

Source 1 or Source 2 power loss Oneofthesourceismissing,

The ATS power on the load with the

source that is present.

Source 1 or Source 2 voltage out

of tolerance

One of the source voltage is out of

tolerance.

The display shows the voltage measure

of the faulty source.

Source 1 or Source 2 frequency

out of tolerance

One of the source frequency is out of

tolerance.

The display shows the frequency

measure of the faulty source.

Source 1 and Source 2 quality The sources are outside ranges so that

it generates too many transfers within a

short period of time.

The alarm resets when the condition

becomesinactive.

2. Presentation

Page 9

EATS16_EN

ENGLISH

3. Installation for ATS

3.1 Checking the accessory kit - EATS16 - EATS16N

• VerifythatthefollowingadditionalitemsareincludedwiththeATS:

EATS16

1 Usermanual

2 Quickstartguide

3 Safety manual printed

4 2xInputcables:C19-C20

5 2xInputcablelockers

6 Plasticstripsforoutputlocking

7 RS232cable

8 Accessoriesforrackinstallation

EATS16N

1 Usermanual

2 Quickstartguide

3 Safety manual printed

4 2xInputcables:C19-C20

5 2xInputcablelockers

6 Plasticstripsforoutputlocking

7 RS232cable

8 DB9/RJ45serialcableforNMCcard

9 Accessoriesforrackinstallation

Page 10 EATS16_EN

3. Installation for ATS

3.2 Storage

• PleasestoretheATSinitsoriginalpackageandinadryplace.

Keepthestoragetemperaturebetween-13to131°F(-25°Cand+55°C).

3.3 Installation for rack mounting (normal installation)

Followsteps1to3formodulemountingontherails.

Accessories for rack installation

• 1xEar(Left)

• 1xEar(Right)

• 4xM4x6atscrewforear

• 4xM6x10cagenutclipforrack4

• 4xM6x12atscrewforrack

• 4xM6washerconicalplateforrack

3.4 Installation for rack mounting (2 post installation)

Followsteps1to3formodulemountingontherails.

Accessories for rack installation

• 1xEar(Left)

• 1xEar(Right)

• 4xM4x6atscrewforear

• 4xM6x10cagenutclipforrack4

• 4xM6x12atscrewforrack

• 4xM6washerconicalplateforrack

Page 11

EATS16_EN

ENGLISH

3.5 Wall installation

Follow steps 1 to 2 for module mounting on the wall.

3.6 Instructions

1.ElevatedOperatingAmbient-Ifinstalledinaclosedormulti-unitrackassembly,theoperatingambient

temperatureoftherackenvironmentmaybegreaterthanroomambient.Therefore,consideration

shouldbegiventoinstallingtheequipmentinanenvironmentcompatiblewiththemaximumambient

temperature(Tmax)speciedbythemanufacturer.

2. ReducedAirFlow-Installationoftheequipmentinarackshouldbesuchthattheamountofairow

required for safe operation of the equipment is not compromised.

3. MechanicalLoading-Mountingoftheequipmentintherackshouldbesuchthatahazardousconditionis

not achieved due to uneven mechanical loading.

4. CircuitOverloading-Considerationshouldbegiventotheconnectionoftheequipmenttothesupply

circuit and the effect that overloading of the circuits might have on overcurrent protection and supply

wiring.Appropriateconsiderationofequipmentnameplateratingsshouldbeusedwhenaddressingthis

concern.

5.ReliableEarthing-Reliablegroundingofrack-mountedequipmentshouldbemaintained.Particular

attentionshouldbegiventosupplyconnectionsotherthandirectconnectionstothebranchcircuit(e.g.

use of power strips).

3. Installation for ATS

Page 12 EATS16_EN

4.1 Installation diagram

ATS

Input

ATS

Input

UPS

Input

UPS

Input

UPS

Output

ATS

Output

to the sensitive equiment

UPS

Output

UPS 1

ATS

UPS 2

4.2 Input/Output connection EATS16 - EATS16N

Inputs connections

from UPSs outputs

Ouput connection to equipment

1.ConnectinputpowercablestoUPSsoutputandtoATSinputs(S1isthedefaultprioritysource).

2. Connect ATS output to the equipment.

4. Power cables connection

Page 13

EATS16_EN

ENGLISH

5. Communication

5.1 Communication ports: EATS16N

• RS232 communication port

• Characteristics of the optocouplers communication port

Whenasignalisactivated,thecontactisclosedbetweenthecommon(Pin4)andthepinofthe

correspondingsignalforn.ocontact,andviceversaforn.ccontact.

6789

common

2345

Pin assignment Description Contact type Open State Close State

Pin 1 Summary alarm signal n.o Normal Alarm occurred

Pin 2 RX - - -

Pin3 TX - - -

Pin 4 Common - - -

Pin 5 GND - - -

Pin 6 Source 1 OK n.c Source 1 is failure Source1isok

Pin 7 Source 2 OK n.c Source 2 is failure Source2isok

Pin8 Loadonsource1 n.c Source1nottakeload Source1takesload

Pin9 Loadonsource2 n.c Source2nottakeload Source2takesload

  n.o:normallyopened

  n.c:normallyclosed

1.ConnecttheRS232 2

communicationcableto

the serial on the computer.

2. Connect the other end of the

communicationcable 2 to the

RS232 1 communication port

on the ATS.

The ATS can now communicate

with EATON power management

software.

Contact characteristics (optocoupler)

• Voltage:48VDCmax

• Current:25mAmax

• Power:1.2 W

Page 14 EATS16_EN

• Connectivity Cards: EATS16N

ConnectivitycardsallowtheATStocommunicateinavarietyofnetworkingenvironmentsandwith

different types of devices. The Network-MS cardhasSNMPandHTTPcapabilitiesaswellasmonitoring

throughaWebbrowserinterface;connectstoEthernetnetwork.Inaddition,anEnvironmentalMonitoring

Probecanbeattachedtoobtainhumidity,temperature,smokealarm,andsecurityinformation.

Network-MS card

ETHERNET

100M 10 M UPS data Reset

Setting/Sensor

5.2 Eaton Intelligent Power Software suite

EatonSoftwaresuiteprovidesup-to-dategraphicsofATSpowerandsystemdataandpowerow.

Italsogivesyouacompleterecordofcriticalpowerevents,anditnotiesyouofimportantATSorpower

information.

5. Communication

Page 15

EATS16_EN

ENGLISH

6. Maintenance

6.1 Troubleshooting

Operation status Possible cause Action

Overload Power requirement exceeds the

ATS capacity (greater than 105 % of

nominal).

Removesomeoftheequipment

from the ATS.The ATS continues

tooperate,butmayshutdown

if the load increases.The alarm

resetswhentheconditionbecomes

inactive.

Short-circuitfault Ashort-circuitoccurred. Checkdeviceconnectionor

integrity.

Iferrorpersists,notethealarm

message and the ATS serial

number,andthencontactyour

service representative.

Internalrelayfault Internalrelayfault,notethatthe

load is no powered. Note the alarm message and the

ATSserialnumber,andthencontact

your service representative.

Source 1 or Source 2 power

supply fault

Internalpowersupplyofoneofthe

sourceisfaulty;theothersourceis

powering the load.

Note the alarm message and the

ATSserialnumber,andthencontact

your service representative.

EEPROMfault EEPROMfault,notethattheloadis

still powered. Note the alarm message and the

ATSserialnumber,andthencontact

your service representative.

Page 16 EATS16_EN

7. Specifications

Table 1. Model list

Model Operating voltage Current rating Operating frequency

EATS16 200/208/220/230/240 Vac 1ɸ16A 50/60Hz

EATS16N

Table 2. Weights and dimensions

Model Dimensions H x W x D (mm/inch) Weight (kg/lb)

EATS16 43 x 438 x 250 /1.7x17.24x9.84 3.32 /7.31

EATS16N 43 x 438 x 250 /1.7x17.24x9.84 3.54 /7.8

Table 3. Electrical input connections

Model Input connection

EATS16-EATS16N IECC20inlet(2xInputcables:C19-C20provided)

Table 4. Electrical output connections

Model Output connection

EATS16-EATS16N 1xC19

8xC13

Table 5. Environmental and safety

Operating temperature 0°Cto40°C(32°Fto104°F)

Storage temperature -25°Cto55°C/-13°Fto131°F

Relative humidity Storage:0-90%

Operating:20-85%

Operating altitude 2000m meters (6252 ft)

Audible noise 25dBAmax(withoutbuzzer)