Edbak TWB1 User Manual
Displayed below is the user manual for TWB1 by Edbak which is a product in the TV Mounts category. This manual has pages.
Related Manuals
4. Security screw
When the screen is hanging securely on the back plate,
tighten solidly two security screws situated in bottom
part of front panels using Philips screw driver.
5. Maintenance
Before maintenance of wall mount it is necessary to turn off and unplug plasma/LCD/LED screen.
Every 6 months run periodical check the condition of screw joints and in case there
Wipe the screen up with dry cloth. If the wall mount is very dirty, it is necessary to remove the dirt first with
neutral cleaner diluted with water, and than wipe the mount up with dry cloth. You can not use such cleaners
like solvent, furniture wax as it may cause peeling off of the powdercoated metal parts.
EDBAK Sp. z o.o.
Piotrowice 186
23-107 Strzyżewice, PL
+48 81 562 81 19
www.edbak.com info@edbak.com
Rev.date: 14-02-2013 12:02
instruction_manual_TWB1[EN]_v.3.1.doc
TWB1
Universal fixed wall mount for
Plasma/LCD/LED 60”-65”
Installation manual
SAFETY WARNING!
Remarks regarding safety and installation
INSTRUCTIONS MUST BE ALWAYS FOLLOWED PRECISELY
1. Before installation read carefully this installation manual and instruction manual of your
plasma/LCD/LED screen for proper installation.
2. Installation of this unit should be carried out by at least two qualified technicians.
3. This unit is not adapted to direct installation on the ceiling surface. Mounting to the ceiling is only
possible with CM1 adapter.
4. EDBAK is not liable for any damage or injury caused by mishandling or improper installation.
5. Maximum capacity load: 80 kg
6. Mounting interface: min. 100x100mm, max 850x460mm
Universal Fixed Wall Mount TWB1
List of components:
1. Back plate – 1 pcs
2. Front plate – 2 pcs..
3. Fixings and spacers - 1 bag
4. Instruction manual – 1 pcs.
Tools required for installation (not
included):
- Allen key nr 3,4,5, 6 – 1 pcs
- Philips PH2 screwdriver – 1 pcs
1
2
1. Mounting back plate on the wall surface
Mounting of the back plate to the wall
should be carried out on in desired
position after prior checking of wall type
and structure and according to building
craft. If you have any doubt please
consult a qualified builder or contractor. It
is not allowed to mount a screen on the
wall which structure is not durable
enough to hold the specified capacity
load.
Mount back plate horizontally to the wall surface
using screws/bolts (not supplied) suitable to the type and
structure of wall.
2. Mounting front plates to the back of plasma / LCD screen
Place plasma/LCD screen face down on soft cloth (to prevent damage) on a flat and stable surface.
Please compile all parts necessary for mounting:
front plate – 2 pcs
screw – 4 pcs.
washer – 4 pcs.
spacer – min. 4 pcs.
In the enclosed bag there are different screws, washers and spacers fitting different types and makes of
plasma/LCD/LED screens. Only ONE set of screws, washers and spacers will be necessary for mounting front
plates to the back of plasma/LCD/LED screen.
Compile set of screws, washers and spacers in the following manner:
-select suitable height of spacers, in order to keep a couple millimeters distance between the back of the
plasma/LCD/LED screen and front panels
-select suitable screws (length and thread), so that after assembling spacers, front panels and washers
together the depth mounting pole back of the plasma/LCD/LED screen is adequate to the length of the
screw thread. Screw can not be too long, because while screwing in it may cause damage to your
screen.
Position front panels as centrally on the back of the screen
Tighten previously selected screws using Allen key.
3. Mounting screen on the back plate
Please be careful while engaging plasma with the
wall!!
Raise the screen in vertical position (at least two people)
with front plates already assembled to the back of the
screen and hang it on the back plate mounted on the wall
surface, so that hooks hang on the edge of the back plate
(please see the drawing).
Make sure that the hooks are hooked on the edge of the back plate.
Top
Bottom
Top of the screen
Bottom of the
screen
Screw
Washer
Front plate
Spacer
Mounting
hole
Center holes
Screen
Allen Key