Edbak VWFX95-L User Manual
Displayed below is the user manual for VWFX95-L by Edbak which is a product in the Video Wall Display Mounts category. This manual has pages.
Related Manuals
Installation Manual
VWFX95-L
90-95” Video Wall Mount, Landscape
ver.1.1 0814
130kg
ver.1.1 0814 p.1
max load
capacity:
ver.1.1 0814 p.2
2 3
1
TABLE OF CONTENTS: TOOLS REQUIRED
FOR INSTALLATION:
(NOT INCLUDED)
1. Safety instructions
2. Table of contents
3. Tools required for installation
4. Parts list
5. Installation to Brick or Concrete Wall
6. Installation to Wood Stud Wall
7. Multiple Display Assembly - use of optional
spacers.
8. Attaching front plates to Display
9. Attaching Display to frame
10. Display Adjustment
• ServiceAccess
• VerticalandHorizontalAdjustment
• DisplayMicroadjustment
11. Cable management
• SpiritLevel
• Studnder
• Drill
• Drillbit
• Pencil
• Phillipsscrewdriver
• Wrench
1. SAFETY INSTRUCTIONS:
Warning:
Please read this manual carefully prior to any installation to ensure proper assembly. The
assembly should be carried out in accordance with this manual by at least two persons with
sufficient qualifications and experience in assembly. EDBAK Company shall not be liable for any
material or property damage or bodily injury resulting from improper assembly. Therefore, you
should always follow the instructions:
- the accompanying elements are intended for mounting on walls of solid wood, brick or concrete
with the use of appropriate screws that are included into the product. In the case of any other
type of walls, please consult a person with sufficient qualifications in construction;
- during the assembly, please follow the instructions carefully. Otherwise it may result in product
damage or even personal injury;
- before the assembly you must ensure that under the surface of the wall where the mount is to
be fixed there are no power cables, water or sewage pipes or gas installations;
- make sure that the supporting surface will safely support the combined load of all attached
hardware and components.
- this product is intended for indoor use only;
- this product was designed, to be installed also in p blic areas.
- do not install the product if it is damaged;
- while fixing the screen on the mount, please ensure that the screws are of correct length and
diameter. In order to ensure the correct length and diameter, you may use the accompanying
plastic pads. Use of improper screws may result in permanent product damage. Extra caution
should be given with movable elements in order to prevent crushing or injury to your hands or
fingers. This manual indicates such elements so please note them carefully.
The terms of the product guarantee are set forth in the guarantee card.
Keep these instruction.
AØ5 x4
BØ8 x4
x4
D x4
EM4x20 x4
FM5x20 x4
GM6x20 x4
HM8x20 x4
IM5x16 x2
J10x80 x6
x1
Lx5
MM6x80 x6
x1
4 PART LIST:
ver.1.1 0814 p.3
Part list
ScrewsandAllenkeys(included)
Allen Key
Frame
2x mounting adapters
5 INSTALLATION TO BRICK OR CONCRETE WALL
J
x4
J
J
ATTENTION!
ATTENTION!
MAKE SURE, THAT THE FRAME IS IN „0”
POSITION”
ver.1.1 0814 p.4
• Fortheinstallationtwopeoplearerequired.
• LocatersttheMountonthewall-makesurethatthemountislevel.
• Markfourmountingholes.MakesurethattheMountislevel.Theframemustbe
xedwithminimumoffourscrews.
• Insertanchorsintheholes
• PlaceMountassemblyoveranchorsandsecurewithfourscrews
6 INSTALLATION TO WOOD STUD WALL
M
M
x4
ver.1.1 0814 p.5
• Fortheinstallationtwopeoplearerequired.
• Useanedge-to-edgestudnder.Drawaverticallinedownthestudcenter.
• LocatersttheMount-makesurethatthemountislevel.
• Markfourmountingholes.MakesurethattheMountislevel.Theframemustbe
xedwithaminimumoffourscrews.
• Drillfourholes.
• Insertanchorsintheholes.
• PlaceMountassemblyoveranchorsandsecurewithfourscrews.
ATTENTION!
ATTENTION!
MAKESURE,THATTHEFRAMEISIN„0”POSITION”
DIS P L AY H E I G H T
A= DIS P AL Y H E I G H T
DIS P L AY WIDTH
A= D IS P L AY WID T H
7 MULTIPLE DISPLAY ASSEMBLY - WITHOUT SPACERS
ver.1.1 0814 p.6
8
ver.1.1 0814 p.7
• InstallrstMountonthewall-seestep5or6dependingonwallstructure
• Additionalframescanbeinstalledusingoptionalspacers(notincluded)
• Designateahorizontalandaverticallineonthewall.Lineswillhelpinmounting
additional Mounts.
• Slidespacersintotabopeningofmountedwallplate.
• Followmaininstructionsforcorrectinstallationofadditionalwallplates
MULTIPLE DISPLAYS ASSEMBLY- USE OF OPTIONAL SPACERS
ATTENTION!
HORIZONTALORIENTATION VERTICALORIENTATION
9
A
A x4; B x4
Ø5 Ø8
E x4; F x4
G x4; H x4 M4x20 M5x20 M6x20 M8x20
ver.1.1 0814 p.8
ATTACHING FRONT PLATES TO THE DISPLAY
• Placedisplayfacedownonasoftsurface.
• Selectscrewdiameterandlengthwithmountingholesondisplay.Ifitisnecessary,
usespacersincludedwithscrewsset.
• Pulluprearpartofthemountingarms.
• Makesurethediamondmarkingsonthefrontplatesarelocatedinthecenterof
the display.
• Usechosenscrews(andspacersifitisnecessary)toconnectthefrontplatesto
the display.
10
ver.1.1 0814 p.9
ATTACHING DISPLAY TO FRAME
• AttachDisplaywiththefrontplatestotheframe-twopeoplearerequired.
• Placedisplayindesiredpositionontheframe.
• Secureeachfrontplateusingthescrew,whichislocatedatthebottomof
mounting arms.
ATTENTION!
SECURE ADAPTERS USING TWO SCREWS.
11
ver.1.1 0814 p.10
DISPLAY ADJUSTMENT
1
2
3
4
HorizontalAdjustment
Tilting Adjustment
Display Micro adjustment
VerticalAdjustment
1.1.HORIZONTALADJUSTMENT
2. TILTING ADJUSTMENT
ver.1.1 0814 p.11
3. DISPLAY MICRO ADJUSTMENT 4.VERTICALADJUSTMENT
A
L
12 CABLE MANAGEMENT
ver.1.1 0814 p.12
• Cableties“L”xedtothecablemanagementslots,situatedonthebottomsections
of the frame, can be used to secure display cables.
Contact Details
Edbak Ltd.
Piotrowice186
23-107Strzyżewice
Poland
Tel. +48 81 562 81 19
Fax +48 81 562 82 90