Table of Contents
EIZO RX660 User Manual
Displayed below is the user manual for RX660 by EIZO which is a product in the Computer Monitors category. This manual has pages.
Related Manuals
English
Instructions for Use
Color LCD monitor
Important
Please read this “Instructions for Use”, and “Installation Manual”
(separate volume) carefully to familiarize yourself with safe and
effective usage.
Please retain this manual for future reference.
• For monitor adjustment and settings, refer to the “Installation
Manual”.
• For the latest product information including the “Instructions for
Use”, refer to our web site :
http://www.eizoglobal.com
2
SAFETY SYMBOLS
This manual and this product use the safety symbols below. They denote critical information. Please read
them carefully.
WARNING
Failure to abide by the information in a
WARNING may result in serious injury
and can be life threatening.
CAUTION
Failure to abide by the information in a
CAUTION may result in moderate injury and/or
property or product damage.
Indicates a warning or caution. For example, indicates an “electrical shock” hazard.
Indicates a prohibited action. For example, means “Do not disassemble”.
Indicates a mandatory action. For example, means “Ground the unit”.
This product has been adjusted specically for use in the region to which it was originally shipped. If
operated outside this region, the product may not perform as stated in the specications.
No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by
any means, electronic, mechanical, or otherwise, without the prior written permission of EIZO Corporation.
EIZO Corporation is under no obligation to hold any submitted material or information condential unless
prior arrangements are made pursuant to EIZO Corporation’s receipt of said information. Although every
effort has been made to ensure that this manual provides up-to-date information, please note that EIZO
monitor specications are subject to change without notice.
3
PRECAUTIONS
English
PRECAUTIONS
IMPORTANT
• This product has been adjusted specically for use in the region to which it was originally shipped.
If the product is used outside the region, it may not operate as specied in the specications.
• To personal safety and proper maintenance, please read carefully this section and the caution
statements on the monitor.
Location of the Caution Statements
AVERTISSEMENT
WARNING
WARNUNG
Symbols on the unit
Symbol This symbol indicates
Main Power Switch: Press to turn the monitor’s main power off.
Main Power Switch: Press to turn the monitor’s main power on.
Power button: Press to turn the monitor’s power on or off.
Alternating current
Alerting electrical hazard
CAUTION: Refer to “SAFETY SYMBOLS” (page 2).
WEEE marking: Product must be disposed of separately; materials may
be recycled.
CE marking: EU conformity mark in accordance with the provisions of
Council Directive and/or Regulation (EU).
Manufacturer
Date of manufacture
4PRECAUTIONS
WARNING
If the unit begins to emit smoke, smells like something is burning, or makes strange noises, discon-
nect all power connections immediately and contact your EIZO representative for advice.
Attempting to use a malfunctioning unit may result in re, electric shock, or equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in re, electric shock, or burn.
Refer all servicing to qualied service personnel.
Do not attempt to service this product yourself as opening or removing covers may result in re, electric
shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet or spillage
into the cabinet may result in re, electric shock, or equipment damage. If an object or
liquid falls/spills into the cabinet, unplug the unit immediately. Have the unit checked by
a qualied service engineer before using it again.
Place the unit at a sturdy and stable place.
A unit placed on an inadequate surface may fall and result in injury or equipment damage. If the unit falls,
disconnect the power immediately and ask your local EIZO representative for advice. Do not continue using
a damaged unit. Using a damaged unit may result in re or electric shock.
Use the unit in an appropriate location.
Otherwise, re, electric shock, or equipment damage may result.
• Do not place outdoors.
• Do not place in any form of transportation (ships, aircraft, trains, automobiles, etc.).
• Do not place in dusty or humid environments.
• Do not place in locations where water may be splashed on the screen (bathrooms, kitchens,
etc.)
• Do not place in locations where steam comes in direct contact with the screen.
• Do not place near heat generating devices or humidiers.
• Do not place in locations where the product is subject to direct sunlight.
• Do not place in environments with inammable gas.
• Do not place in environments with corrosive gases (such as sulfur dioxide, hydrogen sulde,
nitrogen dioxide, chlorine, ammonia, and ozone)
• Do not place in environments with dust, components that accelerate corrosion in the
atmosphere (such as sodium chloride and sulfur), conductive metals, and so on
To avoid danger of suffocation, keep the plastic packing bags away from babies and children.
Use the enclosed power cord and connect to the standard power outlet in your country.
Be sure to use within the rated voltage of the power cord. Otherwise, re or electric shock may result.
Power supply: 100-240Vac 50/60Hz
To disconnect the power cord, grasp the plug rmly and pull.
Tugging on the cord may damage and result in re or electric shock.
The equipment must be connected to a grounded main outlet.
Failure to do so may result in re or electric shock.
Use the correct voltage.
• The unit is designed for use with a specic voltage only. Connection to another voltage than specied in this
“Instructions for Use” may cause re, electric shock, or equipment damage.
Power supply: 100-240Vac 50/60Hz
• Do not overload your power circuit, as this may result in re or electric shock.
5
PRECAUTIONS
English
WARNING
Handle the power cord with care.
• Do not place the cord underneath the unit or other heavy objects.
• Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Using of a damaged cord may result
in re or electric shock.
For electrical safety, do not connect or disconnect the power cord in the presence of patients.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the arm stand and install the unit
securely.
Otherwise, the unit may become detached, resulting in injury and/or equipment damage. Before installation,
make sure that desks, walls, or any other installation surface has adequate mechanical strength. If the unit
falls, please ask your local EIZO representative for advice. Do not continue using a damaged unit. Using
a damaged unit may result in re or electric shock. When reattaching the tilt stand, please use the same
screws and tighten them securely.
Do not touch a damaged LCD panel directly with bare hands.
Liquid crystal is poisonous. If any part of your skin comes in direct contact with the
panel, wash thoroughly. If liquid crystal enters your eyes or mouth, immediately ush
with large amounts of water and seek medical attention.
Fluorescent backlight lamps contain mercury (the products that have LED back-
light lamps contain no mercury), dispose according to local, state or federal
laws.
Exposure to elemental mercury can result in effects on the nervous system, including
tremors, memory loss, and headaches.
6PRECAUTIONS
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit with the power cord or cables
attached is dangerous and may result in injury.
Carry or place the unit according to the correct specied methods.
• When carrying, grasp and rmly hold the unit as shown in the illustration below.
• Monitors of size 30 inches and above are heavy. When unpacking and/or carrying the monitor, ensure at least two
people are utilized.
Dropping the unit may result in injury or equipment damage.
Do not block the ventilation slots on the cabinet.
• Do not place any objects on the ventilation slots.
• Do not install the unit in a place with poor ventilation or inadequate space.
• Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airow and may result in re, electric
shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This is to facilitate disconnecting the power in case of a problem.
Periodically clean the area around the power plug and the ventilation slot of the monitor.
Dust, water, or oil on the plug may result in re.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric shock.
If you plan to leave the unit unused for an extended period of time, disconnect the power cord from
the wall socket after turning off the power switch for the safety and the power conservation.
This product is suitable for placing near patients, but not for direct contact with patients.
For users in the territory of the EEA and Switzerland:
Any serious incident that has occurred in relation to the device should be reported to the
Manufacturer and the Competent Authority of the Member State in which the user and/or patient is
established.
7
Notice for this monitor
English
Notice for this monitor
Intended use
This product is intended to be used in displaying and viewing digital images for review, analysis and
diagnosis by trained medical practitioners. It does not support the display of mammography images for
diagnosis.
Caution: Federal law (USA) restricts this device to sale by or on the order of a physician.
Attention
• This product should be set to horizontal view mode when used for the purposes mentioned above.
• This product may not be covered by warranty for uses other than those described in this manual.
• The specications noted in this manual are only applicable when the following are used:
- Power cords provided with the product
- Signal cables specied by us
• Only use optional products manufactured or specied by us with this product.
Precautions for Use
• Otherwise, parts (such as the LCD panel or the fan) may deteriorate in the long-term. Periodically check
that they are operating normally.
• When the screen image is changed after displaying the same image for extended periods of time, an
afterimage may appear. Use the screen saver or power save function to avoid displaying the same image
for extended periods of time.
• If the monitor displays continuously over a long period of time, dark smudges or burn-in may appear. To
maximize the life of the monitor, we recommend the monitor be turned off periodically.
• An afterimage may appear even after a short time period has elapsed depending on the displayed
image. If this occurs, changing the image or leaving the power off for a few hours may solve the problem.
• The backlight of the LCD panel has a xed lifetime. When the screen becomes dark or begins to icker,
please contact your local EIZO representative.
• The screen may have defective pixels or a small number of light dots on the screen. This is due to the
characteristics of the panel itself, and is not a malfunction of the product.
• Do not press on the panel or edge of the frame strongly, as this may result in display malfunctions, such
as interference patterns, etc. If pressure is continually applied to the panel, it may deteriorate or damage
your panel. (If the pressure marks remain on the panel, leave the monitor with a black or white screen.
The symptom may disappear.)
• Do not scratch or press on the panel with any sharp objects, as this may result in damage to the panel.
Do not attempt to brush with tissues as this may scratch the panel.
• Depending on the environment, the value measured by the built-in illuminance sensor may differ from
the value shown on a stand-alone illuminometer.
• When the monitor is cold and brought into a room or the room temperature goes up quickly, dew
condensation may occur on the interior and exterior surfaces of the monitor. In that case, do not turn the
monitor on. Instead wait until the dew condensation disappears, otherwise it may cause some damage
to the monitor.
8Notice for this monitor
To Use the Monitor for a Long Time
●Maintenance
• The display quality of monitors is affected by the quality level of input signals and the degradation of
the product. Perform visual checks and periodic constancy tests to comply with medical standards /
guidelines according to your application, and carry out calibration as necessary. Use of the RadiCS
monitor quality control software enables you to perform high-level quality control that meets medical
standards / guidelines.
• It takes about 15 minutes for the performance of electrical parts to stabilize. Please wait 15 minutes
or more after the monitor power has been turned on or the monitor has recovered from the power
saving mode, and then adjust the monitor.
• We recommend that monitors be set to the recommended level or lower to reduce changes in
luminosity caused by long-term use and maintain stable brightness.
• Perform correlation using RadiCS/RadiCS LE to adjust the measurement result of the Integrated
Front Sensor to the measurement result of the UX1 sensor for reference. Periodical correlation
enables the measurement accuracy of the Integrated Front Sensor equivalent to that of the UX1
sensor. For details, refer to RadiCS/RadiCS LE User’s Manual.
●Cleaning
Periodic cleaning is recommended to keep the monitor looking new and to prolong its operation
lifetime.
Gently wipe off any dirt on the cabinet or panel surface with a soft cloth soaked in a small amount of
water or one of the chemicals listed below.
Chemicals that may be used for cleaning
Material name Product name
Ethanol Ethanol
Isopropyl alcohol Isopropyl alcohol
Chlorhexidine Hibitane
Benzalkonium chloride Welpas
Alkyldiaminoethylglycine Tego 51
Glutaral Cidex Plus28
Attention
• Do not use chemicals on a frequent basis. Chemicals such as alcohol and antiseptic solution may cause
gloss variation, tarnishing, and fading of the cabinet or panel, and also quality deterioration of the image.
• Never use any thinner, benzene, wax, and abrasive cleaner, which may damage the cabinet or panel.
• Do not let chemicals come into direct contact with the monitor.
Note
• The optional ScreenCleaner is recommended for cleaning the cabinet and panel surface.
To use the monitor comfortably
• Staring at the monitor for a long time tires your eyes. Take a 10-minute rest every hour.
• Look at the screen from a proper distance and from a proper angle.
9
CONTENTS
English
CONTENTS
PRECAUTIONS ...................................................... 3
IMPORTANT .............................................................. 3
Notice for this monitor ......................................... 7
Intended use ............................................................. 7
Precautions for Use ................................................. 7
To Use the Monitor for a Long Time ....................... 8
●Maintenance .................................................... 8
●Cleaning .......................................................... 8
To use the monitor comfortably ............................. 8
CONTENTS ............................................................. 9
Chapter 1 Introduction ..................................... 10
1-1. Features ........................................................10
1-2. Package Contents ........................................12
●EIZO LCD Utility Disk .....................................12
1-3. Controls and Functions ..............................14
Chapter 2 Installation / Connection ................ 15
2-1. Before Installing the Product .....................15
●Installation Requirements ..............................15
2-2. Connecting Cables ......................................16
2-3. Turning On the Power ..................................19
2-4. Adjusting the Screen Height and Angle ....19
2-5. Installing the Cable Cover .......................... 20
Chapter 3 No-Picture Problem ........................ 21
Chapter 4 Specications ................................. 22
4-1. Specications List ...................................... 22
4-2. Compatible Resolutions ............................ 23
4-3. Optional Accessories ................................. 23
Appendix .............................................................. 24
Trademark ............................................................... 24
License / Copyright ................................................ 24
Medical Standard ................................................... 24
EMC Information .................................................... 25
FCC Declaration of Conformity ............................ 29
Declaration of compliance with India RoHS ....... 30
Recycling Information/
Informationen zum Thema Recycling/
Informations sur le recyclage/
Сведения по утилизации .................................... i
10 Chapter 1 Introduction
Chapter 1 Introduction
Thank you very much for choosing an EIZO color LCD monitor.
1-1. Features
●High degree of freedom of layout
This product has the PbyP (Picture by Picture) and PinP (Picture in Picture) functions that can display
up to three signals at the same time.
Single PinPPbyP PbyP + PinP
●Simple wiring
In addition to a DisplayPort input terminal, an output terminal is also provided.
• From the output terminal ( ), a signal can be output to a different monitor.
• In order to display images in PbyP, two signal cables usually need to be connected between the
PC and the monitor. On this model, you can connect it to the PC using one cable. You only need
to connect the supplied DisplayPort cable (PP028) between the output terminal ( ) and the input
terminal ( ).
11
Chapter 1 Introduction
English
●Space-saving design
The monitor has two USB upstream ports. You can operate two PCs using one set of USB devices
(mouse, keyboard, etc.) by switching between the PCs.
●Monitor operation from the mouse and keyboard
Using the RadiCS / RadiCS LE monitor quality control software, you can perform the following
monitor operations using the mouse and keyboard:
• Switching CAL Switch modes
• Switching input signals
• Displaying or hiding the PinP sub window (Hide-and-Seek)
• Switching PCs used to operate USB devices (Switch-and-Go)
Note
• The RadiCS / RadiCS LE software allows you to display or hide the PinP sub window and switch the PC
used to operate USB devices at the same time. For more information about the setup procedure, refer to
RadiCS / RadiCS LE User's Manual.
●Quality control
• This monitor has a built-in calibration sensor (Integrated Front Sensor). This sensor enables the
monitor to perform calibration (SelfCalibration) and Grayscale Check independently.
• Using RadiCS LE that is attached to the monitor, you can manage history related to the monitor,
and the SelfCalibration target and execution schedule.
• The RadiCS monitor quality control software enables you to perform quality control that meets
medical standards / guidelines.
12 Chapter 1 Introduction
1-2. Package Contents
Check that all of the following items are contained in the package. If any of these are missing or
damaged, contact your dealer or local EIZO representative listed on the attached sheet.
Note
• It is recommended that the box and packing materials be stored so that they can be used to move or transport
this product.
• Monitor
• Power cord
• Digital signal cable: PP300 x 2
DisplayPort - DisplayPort
• Digital signal cable: PP028 x 1
DisplayPort - DisplayPort
• Digital signal cable: DD300DL x 1
DVI - DVI (dual link)
• USB cable: UU300 x 2
• Cable cover (Left)
• Cable cover (Right)
• EIZO LCD Utility Disk (CD-ROM)
• Instructions for Use
●EIZO LCD Utility Disk
The CD-ROM contains the following items. Refer to "Readme.txt" on the disk for software startup
procedures or le reference procedures.
• Readme.txt le
• RadiCS LE monitor quality control software (for Windows)
• User’s Manual
Monitor Installation Manual
RadiCS LE User's Manual
• Outline dimensions
RadiCS LE
RadiCS LE enables you to perform the following quality control and monitor operations. For more
information about the software or setup procedures, refer to RadiCS LE User's Manual.
Quality control
• Executing calibration
• Displaying test results in a list and creating a test report
• Setting the SelfCalibration target and execution schedule
Monitor operations
• Switching CAL Switch modes
• Switching input signals
• Displaying or hiding the PinP sub window (Hide-and-Seek)
• Switching PCs used to operate USB devices (Switch-and-Go)
• Entering power saving mode (Backlight Saver)
Attention
• The specications of RadiCS LE are subject to change without notice. The latest version of RadiCS LE is
available for download from our web site: http://www.eizoglobal.com
13
Chapter 1 Introduction
English
To use RadiCS LE
For information on how to install and use RadiCS LE, refer to RadiCS LE User's Manual (on the
CD-ROM).
When using RadiCS LE, connect the monitor to your PC using the supplied USB cable. For more
information about how to connect the monitor, see “2-2. Connecting Cables” (page 16).
Note
• In an environment where it is difcult to connect the USB cable, enabling DDC communication allows you to
RadiCS LE without having to use the USB cable. For information on how to congure DDC communication,
refer to the Installation Manual (on the CD-ROM). In view of the response time and operation stability, USB
connection is recommended.
14 Chapter 1 Introduction
1-3. Controls and Functions
4
3
12
13
14
6 87
2
1
9 10 115
15
Approx. 30°
Setting menu*1
1. Integrated Front Sensor
(Movable)
This sensor is used to perform calibration and Grayscale Check.
2. Ambient Light Sensor This sensor measures environmental illumination. Environmental illuminance
measurement is performed using the RadiCS / RadiCS LE quality control software.
3. Presence Sensor This sensor detects movements made by a person in front of the monitor.
4. Operation switches Displays the operation guide. Set menus according to the operation guide.
5. switch Turns the power on or off.
The switch indicator is lit when you turn the power on. The indicator color differs
depending on the monitor's operation status.
Green: Monitor in operation, Orange: Power saving mode,
Off: Main power / power off
6. Main power switch Turns the main power on or off.
: Off, : On
7. Power connector Connects the power cord.
8. DVI-D connector Connect it to the PC. This corresponds to single screen display, display on the right
screen in PbyP mode, and display on the sub window in PinP mode.
9. DisplayPort input
connector
Connect it to the PC.
: This corresponds to single screen display or display on the left screen in PbyP
mode.
: This corresponds to display on the right screen in dual screen mode or display
on the sub window in PinP mode.
10. DisplayPort output
connector
To set up a daisy-chain connection, connect the cable to the input port of another
monitor.
When this connector is connected to , the signal input to can be displayed in
PbyP mode.
For more information, see “2-2. Connecting Cables” (page 16).
11. USB upstream port Connect this port to the PC when you use software that needs a USB connection or
connect a USB device (peripheral device that supports USB) to the USB downstream
port.
12. Stand The height and angle can be adjusted.
13. USB downstream port Connect it to a USB device. To set up a daisy-chain connection, connect the cable to
the USB upstream port of another monitor.
14. Security lock slot Complies with Kensington’s MicroSaver security system.
15. Cable holder Holds the monitor cables.
*1 For information on how to use, refer to the Installation Manual (on the CD-ROM).
15
Chapter 2 Installation / Connection
English
Chapter 2 Installation / Connection
2-1. Before Installing the Product
Carefully read “PRECAUTIONS” (page 3) and always follow the instructions.
If you place this product on a lacquer-coated desk, the color may adhere to the bottom of the stand due
to the composition of the rubber. Check the desk surface before use.
●Installation Requirements
When installing the monitor in a rack, ensure that there is adequate space around the sides, back and
top of the monitor.
Attention
• Position the monitor so that there is no light to interfere with the screen.
16 Chapter 2 Installation / Connection
2-2. Connecting Cables
Attention
• Check that the monitor and the PC are powered off.
• When replacing the current monitor with this monitor, refer to “4-2. Compatible Resolutions” (page 23) to
change the PC settings for resolution and vertical scan frequency to those that are available for this monitor,
before connecting the PC.
1. Connect signal cables.
Check the shapes of the connectors, and connect the cables. After connecting the DVI cable, tighten
the fasteners to secure the connector.
Single screen display
Signal cable:
DD300DL
Signal cable: PP300 or
Attention
• When using the monitor for single screen display via DisplayPort, connect the monitor to the input connector
.
• When the monitor is used for single screen display via DVI, the refresh rate (the frequency at which the
image on the screen is refreshed) will be reduced. When using the monitor for single screen display, it is
recommended that the monitor be connected to DisplayPort 1.
• When using the monitor for single screen display via DVI, you need to set "Input" in the Setting menu to
"DVI". For details, refer to the Installation Manual (on the CD-ROM).
17
Chapter 2 Installation / Connection
English
PbyP (dual-screen) display
Attention
• When using the monitor for PbyP display, you need to congure "Input" in the Setting menu to select a
combination of signals to be displayed. For details, refer to the Installation Manual (on the CD-ROM).
• When the monitor is used in PbyP mode to display images from two PCs, use of some quality control
features such as calibration may be restricted.
For DisplayPort 1 / DisplayPort 2 For DisplayPort 1 / DVI
Signal cable:
PP300
Signal cable: PP300
Signal cable:
DD300DL
Signal cable: PP300
Note
• When the supplied DisplayPort cable (PP028) is connected to and , the signal input to can be
displayed in PbyP mode. In this case, you need to set “Signal Format” - “DisplayPort 1” - “Version” in the
Setting menu to “1.2”, and “Daisy Chain” to “On”.
• Remove the cap before connecting the cable to and .
Signal cable: PP028Signal cable: PP300
18 Chapter 2 Installation / Connection
Setting up a daisy-chain connection to another monitor
The signal input to is output to another monitor.
Attention
• Visit the EIZO website for information about monitors and graphic boards that can be used for the daisy-
chain connection: http://www.eizoglobal.com
• When connecting the monitor in a daisy-chain conguration, you need to set “Signal Format” -
“DisplayPort 1” - “Version” in the Setting menu to “1.2”, and “Daisy Chain” to “On”.
• Remove the cap before connecting the signal cable.
Signal cable: PP300
Connecting to a Computer
Signal cable: PP300
2.
Plug the power cord into a power outlet and the power connector on the
monitor.
Insert the power cord fully into the monitor.
3.
When you use RadiCS / RadiCS LE or connect a USB device (peripheral device
that supports USB) to the monitor, connect the USB cable to the monitor's
USB upstream port and the PC.
Connecting to the Monitor Connecting to a Computer
Attention
• When connecting the monitor to a PC on which RadiCS / RadiCS LE has been installed, connect the cable
to .
• Remove the cap before using .
Note
• When the monitor is used in PbyP mode to display images from two PCs, use of some quality control
features such as calibration may be restricted.
19
Chapter 2 Installation / Connection
English
2-3. Turning On the Power
1. Touch to turn on the power to the monitor.
The power switch indicator of the monitor lights up green.
If the indicator does not light up, see “Chapter 3 No-Picture Problem” (page 21).
Note
• When the power of the monitor is not on, touching any button except causes to ash.
2.
Turn on the PC.
The screen image appears.
If an image does not appear, refer to “Chapter 3 No-Picture Problem” (page 21) for additional
advice.
Attention
• For the maximum power saving, it is recommended that the Power button be turned off. When not using
the monitor, you can turn off the main power supply or disconnect the power plug so that the power is cut
completely.
Note
• In order to maximize the monitor's lifespan by impeding brightness degradation and to reduce power
consumption, carry out the following:
- Use the power saving function of the PC or monitor.
- Turn off the monitor after using it.
2-4. Adjusting the Screen Height and Angle
Hold left and right edge of the monitor with both hands, and adjust the screen height, tilt and swivel of the
screen to the best condition for working.
Attention
• After the adjustment is nished, make sure that the cables are correctly connected.
20 Chapter 2 Installation / Connection
2-5. Installing the Cable Cover
1. Tidy the cables into the cable holder.
2.
Install the cable cover.
Example: Installing the Cable Cover (Right)
Note
• To remove the cable cover, pull it toward you.
21
Chapter 3 No-Picture Problem
English
Chapter 3 No-Picture Problem
Problem Possible cause and remedy
1. No picture
• Power switch indicator does not light up
• Check whether the power cord is connected properly.
• Turn the main power switch on.
• Touch .
• Turn off the main power, and then turn it on again.
• Power switch indicator lights up: Green • Increase "Brightness", "Contrast", or "Gain" in the Setting
menu. For details, refer to the Installation Manual (on the
CD-ROM).
• Turn off the main power, and then turn it on again.
• Power switch indicator lights up: Orange • Switch the input signal. For details, refer to the Installation
Manual (on the CD-ROM).
• Move the mouse or press any key on the keyboard.
• Check whether the PC is turned on.
• If the Presence Sensor is set to "On", the monitor may be in
power saving mode. Try moving closer to the monitor.
• Check whether the signal cable is connected properly. If
"DisplayPort 1" is selected for the input signal, connect it to
. is used for output when a daisy-chain connection is
set up.
• Turn off the main power, and then turn it on again.
• Power switch indicator blinks: Orange,
Green
• Connect via the signal cable specied by EIZO. Turn off the
main power, and then turn it on again.
• If the signal cable is connected to DisplayPort 1 ( ), try
switching the DisplayPort version. For details, refer to the
Installation Manual (on the CD-ROM).
2. The message below appears. This message appears when the signal is not input correctly
even though the monitor is functioning properly.
• This message appears when no signal is
input.
Example:
• The message shown left may appear, because some PCs do
not output the signal immediately after power-on.
• Check whether the PC is turned on.
• Check whether the signal cable is connected properly.
• Switch the input signal. For details, refer to the Installation
Manual (on the CD-ROM).
• If the signal cable is connected to DisplayPort 1 ( ), try
switching the DisplayPort version.
• Is the signal cable connected to to display a DisplayPort
signal on a single screen? The signal cannot be displayed if
the cable is connected to or .
• Turn off the main power, and then turn it on again.
• The message indicates that the input signal
is out of the specied frequency range.
Example:
• Check whether the PC is congured to meet the resolution
and vertical scan frequency requirements of the monitor (see
“4-2. Compatible Resolutions” (page 23)).
• Reboot the PC.
• Select an appropriate setting using the graphics board’s
utility. For more information, refer to the User’s Manual of the
graphics board.
22 Chapter 4 Specications
Chapter 4 Specications
4-1. Specications List
Type RX660:
RX660-AR:
Anti-Glare
Anti-Reection
LCD Panel Type Color (IPS)
Backlight LED
Size 76 cm (30.0 inch)
Resolution (H x V) 3280 × 2048
Display Size (H x V) 645.5 mm × 403.0 mm
Pixel Pitch 0.19 68 mm
Display Colors 10-bit (DisplayPort*1): 1073.74 million colors (Max.)
8-bit (DisplayPort*1 / DVI): 16.77 million colors
Viewing Angles
(H / V, typical)
176˚ / 176˚
Recommended
Brightness
500 cd/m2
Response Time (typical) 25 ms (black -> white -> black)
Video Signals Input Terminals DisplayPort × 2, DVI-D (dual link) × 1
Output Terminal DisplayPort × 1
Horizontal scanning
frequency
31 kHz - 127 kHz
Vertical scan frequency DisplayPort: 29 Hz - 61 Hz (720×400 : 69 Hz - 71 Hz)
DVI: 22 Hz - 61 Hz (720×400 : 69 Hz - 71 Hz)
Frame Synchronization
mode
29.5 Hz - 30.5 Hz, 59 Hz - 61 Hz
Dot clock DisplayPort : 25.0 MHz - 440 MHz (Single screen display)
25.0 MHz - 240 MHz (PbyP / PinP)
DVI : 25.0 MHz - 240 MHz
USB Port Upstream port × 2, downstream port × 3
Standard USB Specication Revision 2.0
Power Input 100 - 240 VAC ±10 %, 50 / 60 Hz 1.95 A - 0.85 A
Maximum Power
Consumption
190 W or less
Power Save Mode 1.6 W or less*2
Standby Mode 1.6 W or less*3
Physical
Specications
Dimensions ( W × H × D ) 682.5 mm × 490.5 mm - 590.5 mm × 225.0 mm (Tilt: 0˚)
682.5 mm × 533.0 mm - 633.0 mm × 296.0 mm (Tilt: 30˚)
Dimensions ( W × H × D )
(Without Stand)
682.5 mm × 441.0 mm × 88.0 mm
Net Weight Approx. 14.2 kg
Net Weight
(Without Stand)
Approx. 10.1 kg
Height Adjustment Range 100 mm (Tilt: 0˚)
Tilt Up 30˚, down 5˚
Swivel 70˚
Operating
Environmental
Requirements
Temperature 0 ˚C - 35 ˚C (32 ˚F - 95 ˚F)
Humidity 20 % - 80 % R.H. (no condensation)
Air Pressure 540 hPa - 1060 hPa
23
Chapter 4 Specications
English
Transportation
/ Storage
Environmental
Requirements
Temperature -20 ˚C - 60 ˚C (-4 ˚F - 140 ˚F)
Humidity 10 % - 90 % R.H. (no condensation)
Air Pressure 200 hPa - 1060 hPa
*1 The colors of DisplayPort signals displayed on the monitor may differ depending on the monitor settings. For
details of display colors and settings, see “4-2. Compatible Resolutions” (page 23).
*2 When DisplayPort 1 input is used, the USB upstream port is not connected, “Input”: “Single DisplayPort 1”,
“Power Save”: “High”, “DDC”: “Off”, “DP Power Save”: “On”, “DisplayPort 1” - “Version”: “1.1”,
“Daisy Chain”: “OFF”, no external load is connected
*3 When the USB upstream port is not connected, “DP Power Save”: “On”, “DisplayPort 1” - “Version”: “1.1,
“DDC”: “Off”, “Daisy Chain”: “OFF”, no external load is connected
4-2. Compatible Resolutions
The monitor supports the following resolutions. For information about the compatible resolutions of the
PinP sub window, refer to the Installation Manual.
√: Supported
Resolution
(H x V)
Vertical
frequency
(Hz)
DisplayPort DVI
Single screen
display Dual screen
display
(PbyP)*3
Single screen
display
Dual screen
display (PbyP)
Ver. 1.2*1 Ver. 1.1*2
720 × 400 70 √ √ √ √ √
640 × 480 60 √ √ √ √ √
800 × 600 60 √ √ √ √ √
1024 × 768 60 √ √ √ √ √
1280 × 1024 60 √ √ √ √ √
1600 × 1200 60 √ √ √ √ √
1640 × 2048 30 - - √-√
1640 × 2048 60 - - √*4 -√*4
3280 × 2048 23 - - - √-
3280 × 2048 30 -√*4 -√*4 -
3280 × 2048 60 √*4 - - - -
*1 When "Daisy Chain" is set to "Off": 10-bit input, when "Daisy Chain" is set to "On": 8-bit input
*2 10 bit input
*3 Dual screen display using "DisplayPort 1 / DisplayPort 2": 10-bit input, dual screen display using "DisplayPort
1 / DVI": 8-bit input
*4 Recommended resolution
4-3. Optional Accessories
The following accessories are available separately.
For the latest information about the optional accessories and information about the latest compatible
graphics board, refer to our web site. http://www.eizoglobal.com
Calibration Kit EIZO "RadiCS UX1" Ver. 4.5.4 or later
EIZO "RadiCS Version Up Kit" Ver. 4.5.4 or later
Network QC Management Software EIZO "RadiNET Pro" Ver. 4.5.4 or later
EIZO "RadiNET Pro Lite" Ver. 4.5.4 or later
Cleaning Kit EIZO "ScreenCleaner"
Comfort Light for Reading Rooms EIZO "RadiLight"
24 Appendix
Appendix
Trademark
The terms HDMI and HDMI High-Denition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing, LLC in the United States and other countries.
The DisplayPort Compliance Logo and VESA are registered trademarks of the Video Electronics
Standards Association.
The SuperSpeed USB Trident Logo is a registered trademark of USB Implementers
Forum, Inc.
Kensington and Microsaver are registered trademarks of ACCO Brands Corporation.
Thunderbolt is a trademark of Intel Corporation in the United States and/or other countries.
Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United
States and other countries.
Adobe is a registered trademark of Adobe Systems Incorporated in the United States and other
countries.
Apple, Mac OS, Macintosh and ColorSync are registered trademarks of Apple Inc.
EIZO, the EIZO Logo, ColorEdge, DuraVision, FlexScan, FORIS, RadiCS, RadiForce, RadiNET, Raptor
and ScreenManager are registered trademarks of EIZO Corporation in Japan and other countries.
ColorEdge Tablet Controller, ColorNavigator, CuratOR, EcoView NET, EIZO EasyPIX, EIZO Monitor
Congurator, EIZO ScreenSlicer, G-Ignition, i Sound, Quick Color Match, Re/Vue, Screen Administrator
and UniColor Pro are trademarks of EIZO Corporation.
All other company and product names are trademarks or registered trademarks of their respective
owners.
License / Copyright
A round gothic bold bit map font designed by Ricoh is used for the characters displayed on this product.
Medical Standard
• It shall be assured that the nal system is in compliance to IEC60601-1-1 requirement.
• Power supplied equipment can emit electromagnetic waves, that could inuence, limit or result in
malfunction of the monitor. Install the equipment in a controlled environment, where such effects
are avoided.
Classication of Equipment
- Type of protection against electric shock : Class I
- EMC class: EN60601-1-2:2015 Group 1 Class B
- Classication of medical device (EU): Class I
- Mode of operation : Continuous
- IP Class : IPX0
25
Appendix
English
EMC Information
The RadiForce series has a performance that appropriately displays images.
Environments of Intended Use
The RadiForce series is intended to be used in Professional healthcare facility environments such as
clinics and hospitals.
The following environments are not suitable for the RadiForce series to be used:
• Home healthcare environments
• In the vicinity of high-frequency surgical equipments such as electrosurgical knives
• In the vicinity of short-wave therapy equipments
• RF shielded room of the medical equipment systems for MRI
• In shielded location Special environments
• Installed in vehicles including ambulances.
• Other special environments
WARNING
The RadiForce series requires special precautions regarding EMC and need to be installed. You
need to carefully read EMC Information and the "PRECAUTIONS" section in this document, and
observe the following instructions when installing and operating the product.
Be sure to use the cables attached to the product, or cables specied by EIZO.
Use of cables other than those specied or provided by EIZO of this equipment could result in
increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and
improper operation.
Cable length: 3 m max.
The RadiForce series should not be used adjacent to or stacked with other equipment. If adjacent
or stacked use is necessary, the equipment or system should be observed to verify normal
operation in the conguration in which it will be used.
When using a portable RF communication equipment, keep it 30 cm (12 inches) or more away from any part,
including cables, of the RadiForce series. Otherwise, degradation of the performance of this equipment
could result.
Anyone who connects additional equipment to the signal input part or signal output parts,
conguring a medical system, is responsible that the system complies with the requirements of
IEC/EN60601-1-2.
Technical Descriptions
Electromagnetic emissions
The RadiForce series is intended for use in the electromagnetic environment specied below.
The customer or the user of the RadiForce series should assure that it is used in such an environment.
Emission test Compliance Electromagnetic environment - Guidance
RF emissions
CISPR11 / EN55011
Group 1 The RadiForce series uses RF energy only for its internal function.
Therefore, its RF emission are very low and are not likely to cause any interference in
nearby electronic equipment.
RF emissions
CISPR11 / EN55011
Class B The RadiForce series is suitable for use in all establishments, including domestic
establishments and those directly connected to the public low-voltage power supply
network that supplies buildings used for domestic purposes.
Harmonic emissions
IEC / EN61000-3-2
Class D
Voltage uctuations /
icker emissions
IEC / EN61000-3-3
Complies
26 Appendix
Electromagnetic immunity
The RadiForce series has been tested at the following compliance levels according to the testing requirements for profes-
sional healthcare facility environments dened in IEC / EN60601-1-2.
Customers and users of the RadiForce series must ensure that the RadiForce series is used in the following environments:
Immunity test
Test level for professional
healthcare facility
environments
Compliance level Electromagnetic environment - Guidance
Electrostatic dis-
charge (ESD)
IEC / EN61000-4-2
±8 kV contact discharge
±15 kV air discharge
±8 kV contact discharge
±15 kV air discharge
Floors should be wood, concrete or ceramic tile.
If oors are covered with synthetic material, the
relative humidity should be at least 30%.
Electrical fast tran-
sients / bursts
IEC / EN61000-4-4
±2 kV power lines
±1 kV input / output lines
±2 kV power lines
±1 kV input / output lines
Mains power quality should be that of a typical
commercial or hospital environment.
Surges
IEC / EN61000-4-5
±1 kV line to line
±2 kV line to ground
±1 kV line to line
±2 kV line to ground
Mains power quality should be that of a typical
commercial or hospital environment.
Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC / EN61000-4-11
0 % UT (100 % dip in UT)
0.5 cycles and 1 cycle
70 % UT (30 % dip in UT)
25 cycles
0 % UT (100 % dip in UT)
5 sec
0 % UT (100 % dip in UT)
0.5 cycles and 1 cycle
70 % UT (30 % dip in UT)
25 cycles
0 % UT (100 % dip in UT)
5 sec
Mains power quality should be that of a typi-
cal commercial or hospital environment. If the
user of the RadiForce series requires continued
operation during power mains interruptions, it
is recommended that the RadiForce series be
powered from an uninterruptible power supply or
a battery.
Power frequency
magnetic elds
IEC / EN61000-4-8
30 A/m
(50 / 60 Hz)
30 A/m
Power frequency magnetic elds should be at levels
characteristic of a typical location in a typical commercial
or hospital environment.
The product should be kept at least 15 cm away from
the source of power frequency magnetic elds during
use.
27
Appendix
English
Electromagnetic immunity
The RadiForce series has been tested at the following compliance levels according to the testing requirements for profes-
sional healthcare facility environments dened in IEC / EN60601-1-2.
Customers and users of the RadiForce series must ensure that the RadiForce series is used in the following environments:
Immunity test
Test level for professional
healthcare facility
environments
Compliance level Electromagnetic environment - Guidance
Portable and mobile RF
communications equipment
should be used no closer to
any part of the RadiForce
series, including cables,
than the recommended
separation distance cal-
culated from the equation
applicable to the frequency
of the transmitter.
Recommended separation
distance
Conducted distur-
bances induced by
RF elds
IEC / EN61000-4-6
3 Vrms
150 kHz - 80 MHz
3 Vrms d = 1.2√P
6 Vrms
ISM bands between
150 kHz and 80 MHz
6 Vrms
Radiated RF elds
IEC / EN61000-4-3
3 V/m
80 MHz - 2.7 GHz
3 V/m d = 1.2√P, 80 MHz - 800 MHz
d = 2.3√P, 800 MHz - 2.7 GHz
Where “P” is the maximum output power rating of
the transmitter in watts (W) according to the trans-
mitter manufacturer and “d” is the recommended
separation distance in meters (m).
Field strengths from xed RF transmitters, as
determined by an electromagnetic site surveya),
should be less than the compliance level in each
frequency rangeb).
Interference may occur in the vicinity of equip-
ment marked with the following symbol.
Note 1 UT is the a.c. mains voltage prior to application of the test level.
Note 2 At 80 MHz and 800 MHz, the higher frequency range applies.
Note 3 Guidelines regarding conducted disturbances induced by RF elds or radiated RF elds may not apply in all situa-
tions. Electromagnetic propagation is affected by absorption and reection from structures, objects and people.
Note 4 The ISM bands between 150 kHz and 80 MHz are 6.765 MHz to 6.795 MHz, 13.553 MHz to 13.567 MHz, 26.957
MHz to 27.283 MHz, and 40.66 MHz to 40.70 MHz.
a) Field strengths from xed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile ra-
dios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To as-
sess the electromagnetic environment due to xed RF transmitters, an electromagnetic site survey should be considered.
If the measured eld strength in the location in which the RadiForce series is used exceeds the applicable RF compliance
level above, the RadiForce series should be observed to verify normal operation. If abnormal performance is observed,
additional measures may be necessary, such as reorienting or relocating the RadiForce series.
b) Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.
28 Appendix
Recommended separation distances between portable or mobile RF communication equipment
and the RadiForce Series
The RadiForce series is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled.
The customer or the user of the RadiForce series can help prevent electromagnetic interference by maintaining a minimum
distance between portable and mobile RF communications equipment (transmitters) and the RadiForce series.
Immunity to proximity elds from following RF wireless communication equipments has been conrmed:
Test fre-
quency
(MHz)
Bandwidth a)
(MHz)
Service a) Modulation b) Maximum
power
(W)
Minimum
separation
distance
(m)
IEC / EN60601
test level (V/m)
Compliance
level
(V/m)
385 380 - 390 TETRA 400
Pulse modulation b)
18 Hz
1.8 0.3 27 27
450 430 - 470 GMRS 460,
FRS 460
FM
±5 kHz deviation
1 kHz sine
2 0.3 28 28
710 704 - 787 LTE Band 13, 17
Pulse modulation b)
217 Hz
0.2 0.3 9 9
745
780
810 800 - 960 GSM 800 / 900,
TETRA 800,
iDEN 820
CDMA 850,
LTE Band 5
Pulse modulation b)
18 Hz
2 0.3 28 28
870
930
1720 1700 - 1990 GSM 1800;
CDMA 1900;
GSM 1900;
DECT;
LTE Band 1, 3, 4,
25;
UMTS
Pulse modulation b)
217 Hz
2 0.3 28 28
1845
1970
2450 2400 - 2570 Bluetooth,
WLAN,
802.11 b/g/n,
RFID 2450,
LTE Band 7
Pulse modulation b)
217 Hz
2 0.3 28 28
5240 5100 - 5800 WLAN 802.11 a/n
Pulse modulation b)
217 Hz
0.2 0.3 9 9
5500
5785
a) For some services, only the uplink frequencies are included.
b) carrier are modulated using a 50 % duty cycle square wave signal.
The RadiForce series is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. For other por-
table and mobile RF communication equipments (transmitters), minimum distance between portable and mobile RF communications equipment
(transmitters) and the RadiForce series as recommended below, according to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter
(W)
Separation distance according to frequency of transmitter
(m)
150 kHz to 80 MHz
d = 1.2√P 80 MHz to 800 MHz
d = 1.2√P 800 MHz to 2.7 GHz
d = 2.3√P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
11.2 1.2 2.3
10 3.8 3.8 7. 3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance “d” in meters (m)
can be estimated using the equation applicable to the frequency of the transmitter, where “P” is the maximum output power
rating of the transmitter in watts (W) according to the transmitter manufacturer.
Note 1 At 80 MHz and 800 MHz, the separation distance for a higher frequency range applies.
Note 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reection from structures, objects and people.
Cable Length
Signal cable: PP300 3 m
Signal cable: PP028 0.28 m
Signal cable: DD300DL 3 m
USB cable: UU300 3 m
Power cord (with earth) 3 m
29
Appendix
English
FCC Declaration of Conformity
For U.S.A., Canada Only
FCC Declaration of Conformity
We, the Responsible Party EIZO Inc.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product Trade name: EIZO
Model: RadiForce RX660
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modi cations not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Note
Use the attached speci ed cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
30 Appendix
Declaration of compliance with India RoHS
We, EIZO Corporation, hereby declare and guarantee that this product has been designed and
manufactured in compliance with the E-Waste management rule 2016 which prohibit the inclusion of the
following substances except for the exemptions listed in schedule II.
- Lead, Mercury, Hexavalent Chromium, Polybrominated Biphenyls or Polybrominated Diphenyl Ethers
exceeding a concentration of 0.1% by weight in homogeneous materials
- Cadmium exceeding a concentration of 0.01% by weight in homogeneous materials
For information on proper disposal and recycling of the product, please refer to the following website.
eizo.co.in/e-waste.php
i
Recycling Information/Informationen zum Thema Recycling/
Informations sur le recyclage/Сведения по утилизации
Recycling Information
This product, when disposed of, is supposed to be collected and recycled according to your country’s
legislation to reduce environmental burden. When you dispose of this product, please contact a distributor or
an af liate in your country.
The contact addressees are listed on the EIZO website below.
http://www.eizoglobal.com
For recycling information for customers in Switzerland, please refer to the following website.
http://www.swico.ch
Informationen zum Thema Recycling
Dieses Produkt muss gemäß den Vorschriften Ihres Landes zur Entlastung der Umwelt recyclet werden.
Wenden Sie sich bei der Entsorgung dieses Produkts an einen Verteiler oder eine Tochtergesellschaft in
Ihrem Land.
Die Adressen zur Kontaktaufnahme sind auf der unten angegebenen Website von EIZO aufgeführt.
http://www.eizoglobal.com
Kunden in der Schweiz entnehmen Informationen zum Recycling der folgenden Website:
http://www.swico.ch
Informations sur le recyclage
Ce produit doit être jeté aux points de collecte prévus à cet effet et recyclé conformément à la législation de
votre pays, a n de réduire l’impact sur l’environnement. Lorsque vous jetez ce produit, veuillez contacter un
distributeur ou une société af liée de votre pays.
Les adresses des distributeurs sont répertoriées sur le site Web EIZO ci-dessous.
http://www.eizoglobal.com
Pour les clients en Suisse, veuillez consulter le site Web suivant afin d’obtenir des informations sur le
recyclage.
http://www.swico.ch
Información sobre reciclaje
Este producto debe desecharse y reciclarse según la legislación del país para reducir el impacto
medioambiental. Cuando desee deshacerse de este producto, póngase en contacto con un distribuidor o
una lial de su país.
Encontrará las direcciones de contacto en el sitio web de EIZO que se indica a continuación.
http://www.eizoglobal.com
Informazioni sul riciclaggio
Per lo smaltimento e il riciclaggio del presente prodotto, attenersi alle normative vigenti nel proprio paese per
ridurre l’impatto ambientale. Per lo smaltimento, rivolgersi ad un distributore o un af liato presenti nel proprio
paese.
Gli indirizzi sono elencati nel sito Web EIZO riportato di seguito.
http://www.eizoglobal.com
Per informazioni sul riciclaggio per i clienti in Svizzera, consultare il sito Web riportato di seguito.
http://www.swico.ch
Återvinningsinformation
När denna produkt kasseras ska den hanteras och återvinnas enligt landets föreskrifter för att reducera
miljöpåverkan. När du kasserar produkten ska du kontakta en distributör eller representant i ditt land.
Kontaktadresserna listas på EIZO-webbplatsen nedan.
http://www.eizoglobal.com
English РусскийFrançaisDeutsch
ii
Πληροφορίες ανακύκλωσης
Το προϊόν αυτό, όταν απορρίπτεται, πρέπει να συλλέγεται και να ανακυκλώνεται σύμφωνα με τη νομοθεσία
της χώρας σας έτσι ώστε να μην επιβαρύνει το περιβάλλον. Για να απορρίψετε το προϊόν, επικοινωνήστε με
έναν αντιπρόσωπο ή μια θυγατρική εταιρεία στη χώρα σας.
Οι διευθύνσεις επικοινωνίας αναγράφονται στην τοποθεσία web της EIZO παρακάτω.
http://www.eizoglobal.com
Сведения по утилизации
По истечении срока службы данного продукта его следует принести на сборный пункт и
утилизировать в соответствии с действующими предписаниями в вашей стране, чтобы уменьшить
вредное воздействие на окружающую среду. Прежде чем выбросить данный продукт, обратитесь к
дистрибьютору или в местное представительство компании в вашей стране.
Контактные адреса можно найти на веб-узле EIZO.
http://www.eizoglobal.com
Informatie over recycling
Wanneer u dit product wilt weggooien, moet het uit milieu-overwegingen worden verzameld en gerecycled
volgens de betreffende wetgeving van uw land. Wanneer u dit product wilt weggooien, moet u contact
opnemen met een distributeur of een partner in uw land.
De contactadressen worden vermeld op de volgende EIZO-website.
http://www.eizoglobal.com
Informação sobre reciclagem
Este produto, quando o deitar fora, deve ser recolhido e reciclado de acordo com a legislação do seu país
para reduzir a poluição. Quando deitar fora este produto, contacte um distribuidor ou uma lial no seu país.
Os endereços de contacto estão listados no website do EIZO, abaixo.
http://www.eizoglobal.com
Oplysninger om genbrug
Dette produkt forventes ved bortskaffelse at blive indsamlet og genbrugt i overensstemmelse med
lovgivningen i dit land for at reducere belastningen af miljøet. Når du bortskaffer denne produkt, skal du
kontakte en distributør eller et tilknyttet selskab i dit land.
Adresserne på kontaktpersonerne er angivet på EIZO’s websted nedenfor.
http://www.eizoglobal.com
Kierrätystä koskevia tietoja
Tuote tulee hävittää kierrättämällä maan lainsäädännön mukaisesti ympäristön kuormittumisen
vähentämiseksi. Kun hävität tuotteen, ota yhteyttä jälleenmyyjään tai tytäryhtiöön maassasi.
Yhteystiedot löytyvät EIZOn Internet-sivustolta.
http://www.eizoglobal.com
Wykorzystanie surowców wtórnych
Ten produkt po zużyciu powinien być zbierany i przetwarzany zgodnie z krajowymi przepisami dotyczącymi
ochrony środowiska. Wyrzucając ten produkt, należy skontaktować się z lokalnym dystrybutorem lub
partnerem. Adresy kontaktowe można znaleźć we wskazanej poniżej witrynie internetowej rmy EIZO.
http://www.eizoglobal.com
iii
Informace o recyklaci
Při likvidaci produktu musí být produkt vyzvednut a recyklován podle zákonů příslušné země, aby
nedocházelo k zatěžování životního prostředí. Zbavujete-li se produktu, kontaktujte distributora nebo
pobočku ve své zemi.
Kontaktní adresy jsou uvedeny na následující webové stránce společnosti EIZO.
http://www.eizoglobal.com
Ringlussevõtu alane teave
Keskkonnakoormuse vähendamiseks tuleks kasutatud tooted kokku koguda ja võtta ringlusse vastavalt teie
riigi seadustele. Kui kõrvaldate käesoleva toote, võtke palun ühendust turustaja või liaaliga oma riigis.
Kontaktisikud on toodud EIZO veebilehel järgmisel aadressil:
http://www.eizoglobal.com
Újrahasznosítási információ
Jelen terméket, amikor eldobjuk, az illető ország törvényei alapján kell összegyűjteni és újrahasznosítani,
hogy csökkentsük a környezet terhelését. Amikor ezt a terméket eldobja, kérjük lépjen kapcsolatba egy
országon belüli forgalmazóval vagy társvállalkozással.
A kapcsolat címei az EIZO alábbi weboldalán találhatók felsorolva:
http://www.eizoglobal.com
Podatki o recikliranju
Ob koncu uporabe odslužen izdelek izročite na zbirno mesto za recikliranje v skladu z okoljevarstveno
zakonodajo vaše države. Prosimo, da se pri odstranjevanju izdelka obrnete na lokalnega distributerja ali
podružnico.
Kontaktni naslovi so objavljeni na spodaj navedenih spletnih straneh EIZO:
http://www.eizoglobal.com
Informácie o recyklácii
Pri likvidácii musí byť tento výrobok recyklovaný v súlade s legislatívou vašej krajiny, aby sa znížilo zaťaženie
životného prostredia. Keď sa chcete zbaviť tohto výrobku, kontaktujte prosím distribútora alebo pobočku vo
vašej krajine.
Zoznam kontaktných adries je uvedený na nasledovnej webovej stránke rmy EIZO:
http://www.eizoglobal.com
Pārstrādes informācija
Utilizējot šo produktu, tā savākšana un pārstrāde veicama atbilstoši jūsu valsts likumdošanas prasībām
attiecībā uz slodzes uz vidi samazināšanu. Lai veiktu šī produkta utilizāciju, sazinieties ar izplatītāju vai
pārstāvniecību jūsu valstī.
Kontaktadreses ir norādītas zemāk minētajā EIZO tīmekļa vietnē.
http://www.eizoglobal.com
Informacija apie grąžinamąjį perdirbimą
Šalinant (išmetant) šiuos gaminius juos reikia surinkti ir perdirbti grąžinamuoju būdu pagal jūsų šalies teisės
aktus, siekiant sumažinti aplinkos teršimą. Kai reikia išmesti šį gaminį, kreipkitės į jūsų šalyje veikiančią
gaminių pardavimo atstovybę arba jos lialą.
Kontaktiniai adresatai nurodyti EIZO interneto svetainėje.
http://www.eizoglobal.com
English РусскийFrançaisDeutsch
iv
Информация относно рециклиране
При изхвърлянето на този продукт се предлага събирането и рециклирането му съобразно законите на
вашата страна за да се намали замърсяването на околната среда. Когато искате да се освободите от
този продукт, моля свържете се с търговския му представител или със съответните органи отговарящи
за това във вашата страна.
Данните за връзка с нас са описани на следния Интернет сайт на EIZO:
http://www.eizoglobal.com
Informaţie referitoare la reciclare
Acest produs, când debarasat, trebuie colectat şi reciclat conform legislaţiei ţării rspective ca să reducem
sarcina mediului. Când se debarasează de acest produs, vă rugăm să contactaţi un distribuitor sau un a liat
al ţării respective.
Adresele de contact le găsiţi pe pagina de web al EIZO:
http://www.eizoglobal.com
http://www.eizoglobal.com
Geri Dönüşüm Bilgisi
Bu ürünün, atılacağı zaman, ülkenizin çevre kirliliğinin azaltılması konusundaki mevzuatına göre toplanması
ve yeniden değerlendirilmesi gerekmektedir. Ürünü atacağınız zaman lütfen ülkenizdeki bir distribütör veya
ilgili kuruluşla temasa geçiniz.
İrtibat adresleri aşağıdaki EIZO web sitesinde verilmiştir.
http://www.eizoglobal.com
Copyright © 2016-2019 EIZO Corporation. All rights reserved.4th Edition - October 15th, 2019 Printed in Japan.
00N0L988D1
IFU-RX660-6
http://www.eizoglobal.com
Carl-Benz-Straße 3, 76761 Rülzheim, Germany
中国苏州市苏州工业园区展业路 8号中新科技工业坊 5B
153 Shimokashiwano, Hakusan, Ishikawa 924-8566 Japan